WARNING! - Lone Wolf Portable Treestands · 2008. 5. 7. · LONE WOLF PORTABLE TREESTANDS PO Box 62...

WARNING!• Make sure you have read and understand all instructions.• Practice first at ground level.• Always wear TMA approved fall arrest system when using

any treestand.• Do not use while intoxicated or when taking medications that

cause drowsiness.• Do not attach to rotten, loose bark or dead trees, metal or

utility poles.• Avoid use during wet or icy conditions, or during lightning storms.• Haul gun or bow up from ground after climbing tree.• Platform is designed to hold one person only.• Do not jump on platform or seat, nor should you stand on seat.• Do not attempt to alter product in any way.• Maximum load is 350 pounds, except where noted.• Failure to follow these instructions could cause serious injury or death.

WARNING!You must read and understand all of the following instructionsbefore first use. If you do not, it could result in serious injury upto and including death. Any questions please call 309-691-9653.

ALWAYS WEAR A TMA APPROVED FALL ARRESTSYSTEM WHEN USING ANY TREESTAND

If you do not understand any of these instructions, please call Customer Service (309-691-9653) or

visit our web site (www.lonewolfstands.com)

LONE WOLF PORTABLE TREESTANDSPO Box 62

Edwards, IL 61528Phone: (309) 691-9653 • Fax: (309) 693-9410

www.lonewolfstands.com

PRODUCT LINEINSTRUCTIONS

MANUAL

1

WARNING!• Make sure you have read and understand all instructions.• Practice first at ground level.• Always wear TMA approved fall arrest system when using

any treestand.• Do not use while intoxicated or when taking medications that

cause drowsiness.• Do not attach to rotten, loose bark or dead trees, metal or

utility poles.• Avoid use during wet or icy conditions, or during lightning storms.• Haul gun or bow up from ground after climbing tree.• Platform is designed to hold one person only.• Do not jump on platform or seat, nor should you stand on seat.• Do not attempt to alter product in any way.• Maximum load is 350 pounds, except where noted.• Failure to follow these instructions could cause serious injury or death.

WARNING!You must read and understand all of the following instructionsbefore first use. If you do not, it could result in serious injury upto and including death. Any questions please call 309-691-9653.




2

TABLE OF CONTENTSLONE WOLF FALL ARREST SYSTEM . . . . . . . . . . . 4

LINEMAN’S ROPE . . . . . . . . . . . . . . . . . . . . . . . . . . 7TREE ATTACHMENT ROPE ASSEMBLY . . . . . . 9

LONE WOLF CLIMBING STICKS . . . . . . . . . . . . . . 12LONE WOLF CLIMBING STICKSLONE WOLF MINI STICKSPRO SERIES CLIMBING STICKS

LONE WOLF HANG ON STANDS . . . . . . . . . . . . . 15ASSAULT™ HANG ON, ALPHA™ HANG ON,ELITE™ HANG ON, PRO SERIES HANG ON

LONE WOLF ASSASSIN™ . . . . . . . . . . . . . . . . . . . . . 21

LONE WOLF CLIMBING STANDS . . . . . . . . . . . . . 27ALPHA™ HAND CLIMBERALPHA™ SIT & CLIMB

LONE WOLF ALPHA™ LADDER STAND . . . . . . . 44

LONE WOLF TREE SEAT . . . . . . . . . . . . . . . . . . . . . . 53

LONE WOLF CAMERA ARM . . . . . . . . . . . . . . . . . . 55

LONE WOLF BACK PACK STRAPSATTACHMENT INSTRUCTIONS

ALPHA™ HANG ON: . . . . . . . . . . . . . . . . . . . . . . . 56ASSAULT™ HANG ON: . . . . . . . . . . . . . . . . . . . . . 57PADDED STRAPS: . . . . . . . . . . . . . . . . . . . . . . . . . 58

LONE WOLF CLIMBING STICKS ATTACHMENTTO STAND FOR BACK PACKING . . . . . . . . . . . . . 59

Copyright © 2008 Lone Wolf Portable Treestands 04/08-15M

3

• Make sure all nuts and bolts are secure before each use.• Replace any worn or damaged parts with components from Lone Wolf.• All bolts for this product are Grade 8.

POLYURETHANE TRACTION BELTAPPLICABLE TO: Alpha™ Sit & Climb and Alpha™ Hand Climber

1.) With a permanent marker write date of 1st use on each belt.2.) Inspect belt before each use3.) Replace every 5 years or when you observe any of the following:

a.) belt has external cracks or tears visibleb.) any internal cables are brokenc.) any teeth are offset from normal pitch or are torn or cut

Shown is the proper use of the traction belt for the Lone Wolf Climbers (dia 1). Thepolyurethane belts are designed to be usedon the Lone Wolf products only. Always useyour traction in the position that it is shown india 1. Never use the belt in this position (dia. 2).Use in this position can cause damage to thetraction belt. WARNING: Point of arrow marksthe end of the belt (dia. 2a). No part of thearrow should be showing after the cams areengaged (dia. 1a). Any failure to follow theinstructions may cause belt to disengage and cam to open.

General Maintenance

POLYESTER WEB BELTSAPPLICABLE TO: Alpha™ Ladder Stand, Climbing Sticks, Elite™ Hang on, Alpha™ Hang On,

Assault™ Hang On, and Assassin™ Platform, Pro Series Hang On & Climbing Sticks

1.) Inspect belts before each use2.) Replace every 5 years or every year if left out yearly3.) Replace belts if you observe any of the following:

a.) cut or worn webbingb.) buckles are bent or cam release is bindingc.) stitching is loose, cut, or becoming unraveled

4.) With a permanent marker write the date of the 1st use on each belt

CORRECT INCORRECT

CORRECT INCORRECT

(dia. 1) (dia. 2)

(dia. 1a) (dia. 2a)

4

Lone Wolf Fall Arrest System

WARNING!• Make sure you have read and understand all instructions.• Practice first at ground level.• Always wear TMA approved fall arrest system when using any treestand.• Do not use while intoxicated or when taking medications that cause drowsiness.• Do not attach to rotten, loose bark or dead trees, metal or utility poles.• Avoid use during wet or icy conditions, or during lightning storms.• Haul gun or bow up from ground after climbing tree.• Platform is designed to hold one person only.• Do not jump on platform or seat, nor should you stand on seat.• Do not attempt to alter product in any way.• Maximum load is 350 pounds, except where noted.• Failure to follow these instructions could cause serious injury or death.

GENERAL MAINTENANCE• Inspect before each use.• Replace every 5 years.• Replace after arresting a fall, or earlier if belts or ropes are cut or worn.




5




Lone Wolf Fall Arrest System

Step 1: Place harness over your shoulders.

Step 2: Take your waist belt threading itthrough the buckle making sure that it issnug against your waist.

Step 3: Take your leg strap from the front to the back making sure to make adjust-ments so that the buckle is even with your waist belt. You will then take your hookunderneath your waist belt bringing it down securely against the waist strap.

continued

6




Lone Wolf Fall Arrest Systemcontinued

Step 4: Repeat the same process on the other side adjusting the tension makingsure the hook is even with your waist belt coming up underneath and hooking downon your waist belt. This should allow your tether to be clear and free in the back.

7




Fall Arrest System’s Lineman’s Rope


GENERAL MAINTENANCE• Inspect before each use.• Replace every 5 years or earlier if belts or ropes are cut or worn.

8




Step 1: Place rope tether’s large loopunder the waist belt as shown.

Step 2: Thread the remainder of therope and carabineer through the largeloop and pull tight.

Step 3: Wrap the rope and carabineer around the tree.

Step 4: Hook the carabineer through the waist belt slidingthe Prusik knot for adjusting the length of the rope.

Fall Arrest System’s Lineman’s Rope

continued

9




Fall Arrest System TreeAttachment Rope Assembly


GENERAL MAINTENANCE• Inspect before each use.• Replace every 5 years.• Replace after arresting a fall, or earlier if belts or ropes are cut or worn.

10




There is a large and small loop on the rope assembly. Always make sure that thesmall loop is always attached to the carabineer.


continued

Step 1: Wrap the rope around the tree and then thread the carabineer and the Prusikknot through the large loop making sure you go through the large loop two times.

11





continued

Step 2: Pull the rope assembly tightagainst the tree as shown.

Step 3: Slide the Prusik knot up againstthe tree tightly.

Step 4: Attach the tether from the harness onto the carabineer.

Step 5: Slide the rope assembly toabove your head.

12




Lone Wolf Climbing Sticks( Applicable to all Lone Wolf Climbing Sticks and Pro Series Climbing Sticks)


GENERAL MAINTENANCE• Make sure all nuts and bolts are secure before each use.• Replace any worn or damaged parts with components from Lone Wolf.• All bolts for this product are Grade 8.

POLYESTER WEB BELT• Replace every 5 years or every 2 years if left out yearly.• Inspect belts before each use.• Replace belts when you observe any of the following:

a.) Cut or worn webbing.b.) Buckles are bent or cam release is binding.c.) Stitching is loose, cut or becoming unraveled.d.) With permanent markers write date of first use on each belt.

13





continued

14




Step 1: Place the Climbing Stick v-bracket against the center of the tree. Wrap thebelt around the tree and then place the open loop over the versa button. You thenpull the belt tight.


continued

Step 2: While holding the top 2 stepswith both hands, pull down until theclimbing stick is firmly attached to thetree.

Step 3: Slide the rope assembly up thetree before you proceed to install yournext stick.

Step 4: Continue this process until you are at your desired hunting height.

15




Lone Wolf Hang On Stands(Assault™ Hang On, Alpha™ Hang On, Elite™ Hang On, Pro Series Hang On)





16




Step 1: While holding the stand in an open position, center the offset bracketagainst the tree. With the buckle in hand, wrap the belt around the tree and placethe loop over the top versa button and pull the belt tight.

SYSTEM 1: Offset Bracket(NOT to be used with EZ Hang Hook System)


continued

ASSAULT™ HANG ON (HOSAT) ALPHA™ HANG-ON (HOSSH) ELITE™ HANG ON (EHOS)

17




Step 3: Lower the platform. Your additional strap can be added at this time.

Step 2: Lift the platform up and pull the belt tight again to take up any additionalslack in the belt. Pushing down on the rear of the seat at this time will help to ensurea solid set.

SYSTEM 1: Offset Bracket continued

(NOT to be used with EZ Hang Hook System)


continued

18




SYSTEM 2: EZ Hang Hook(NOT to be used with Offset Bracket)

Step 1: Fasten the belt hook assembly to the tree. Pull the belt tight.

Step 4: Hold the seat and the tree withyour hands. Your treestand should bepositioned so that you are steppingdownward from your climbing sticks into the center of the platform.

SYSTEM 1: Offset Bracket continued

(NOT to be used with EZ Hang Hook System)


continued

19




SYSTEM 2: EZ Hang Hook continued

(NOT to be used with Offset Bracket)


continued

Step 4: Hold the seat and tree withyour hands while stepping downwardinto the center of the platform. PLEASENOTE: Your treestand should always bepositioned so that you are always steppingdownward from your climbing sticks intothe center of your platform.

Step 2: Hang the stand onto the hook.Please NOTE: make sure to visuallycheck that the hook is in the receiver.

Step 3: Wrap the main belt around thetree. Place the sewn loop over the topversa button and pull tight. You must usethe belt on the top versa button whenusing the easy hang hook. Center theplatform against the tree and lower theplatform.

20




SYSTEM 3: Platform LevelerShown is the platform leveling device. Inorder to level your platform, loosen bothknobs. Next, place the bar in the selectedslot for a level platform. Once that positionis selected, re-tighten the knobs.

SYSTEM 3: Seat LevelerThe seat leveler can be adjusted byslightly screwing the leveling bolt in orout for your desired position.


continued

21




Lone Wolf Assassin™





22




Lone Wolf Assassin™continued

Step 1: Step into harness as shown. Step 2: Pull the harness up to your waist.

Assassin™ Harness

LONE WOLF ASSASSIN™

23





Step 3: Take the top straps up and overfrom the back over your shoulders.

Step 4: Take the waist belt through theopen loops at the end of the upperstraps.

Step 5:Thread the waist strap throughthe buckle on the other side of the waistbelt. Once the belt is threaded, take theexcess back over the buckle and throughthe first side of the buckle pulling tightly.The excess strap can be placed throughthe open loops for convenience.

Step 6: Take your leg strap from theback side underneath to the front of you.

Assassin™ Harness: continued

24





Assassin™ Harness: continued

Assassin™ Tree Strap

Step 1: Place the strap around the tree.

Step 2: Take the end of the strap andthread it through the cinch buckle goingfrom the bottom to the top and over theslide bringing it down through the end ofthe buckle.

Now you are ready to apply the tree strap.

Step 7: Thread the strap through themetal D-rings and pull tight.

Step 8: Repeat this for the oppositeleg, again, coming from the back to thefront threading through the D-ring loopspulling tightly.

25





Assassin™ Tree Strap: continued

Assassin™ Platform

Step 1: Hold the platform against thetree with the platform in an upright posi-tion. Center the offset bracket againstthe tree.

Step 2: With the buckle in hand, wrapthe belt around the tree and place thebelt loop over the versa button and pullthe belt tight.

Step 3: Pull the strap tightly against the tree.

Step 4: Thread the end of the treestrap through the slide on the back side of the strap.

26





Assassin™ Platform: continued

Step 5: Now that you are on your platformat your desired height, the tree strap shouldbe placed in a position somewhere betweenyour midsection and your chest.

Step 3: Push down on the front of theplatform. Wedge the platform tightlyagainst the tree.

Step 4: To level the platform, turn theleveling bolt at the base of the Assassin™

post to adjust the platform angle.

27




Lone Wolf Climbing Stands(Applicable to the Alpha™ Hand Climber and Alpha™ Sit and Climb.

Includes: Back Packing straps, Seat Cushion, Bungee Cord, Stabilizer Straps and 6-Pt Fall Arrest System.)



POLYURETHANE TRACTION BELT• Replace every 5 years.• Inspect belts before each use.• Replace belts when you observe any of the following:

a.) Belt has external cracks or tears visible.b.) Any internal cables are broken.c.) Any teeth are offset from normal pitch, or are torn or cut.d.) With permanent markers write date of first use on each belt.

28




continued

ALPHA™ HAND CLIMBER (HCCSH) ALPHA™ SIT & CLIMB (SACCSH)

Lone Wolf Climbing StandsPOLYURETHANE TRACTION BELT continued

1.) With a permanent marker write date of 1st use on each belt.2.) Inspect belt before each use3.) Replace every 5 years or when you observe any of the following:

a.) belt has external cracks or tears visibleb.) any internal cables are brokenc.) any teeth are offset from normal pitch or are torn or cut

Shown is the proper use of the traction belt for the Lone Wolf Climbers (dia 1). Thepolyurethane belts are designed to be usedon the Lone Wolf products only. Always useyour traction in the position that it is shown india 1. Never use the belt in this position (dia. 2).Use in this position can cause damage to thetraction belt. WARNING: Point of arrow marksthe end of the belt (dia. 2a). No part of thearrow should be showing after the cams areengaged (dia. 1a). Any failure to follow theinstructions may cause belt to disengage and cam to open.

CORRECT INCORRECT

CORRECT INCORRECT

(dia. 1) (dia. 2)

(dia. 1a) (dia. 2a)

29




Step 3: Pull the cord to the end of the slot.

Cam Tethers

Step 1: Run the tether through the holein the end of the cam.

Step 2: Tie the ends together.

continuedLone Wolf Climbing Stands

30




Stabilizer Strap Installation—Climber SeatAlpha™ Hand Climber and Alpha™ Sit and Climb.

Step 1: For the HAND CLIMBER TOPSECTION take the short end of the sta-bilizer straps and take it over the castingin the front corner of the seat through thesewn loop.

Step 2: Pull tight.

Step 1: For the SIT AND CLIMB TOPSECTION, wrap the short end of thestrap under the angled support arm atthe location shown. Make sure the sewnloop is to the outside.

Step 2: Thread the buckle in throughthe sewn loop and cinch it up tight.Rotate the stabilizer buckle so it pointsdownward.


31




Step 1: To install the straps on theSTAND BASE thread the long end of thestrap long end of the strap along theedge frame of the casting just in front ofthe brush pocket towards the rear.

Step 2: Run the sewn loop through andpull tight.

Stabilizer Strap Installation—Climber BaseApplicable to Alpha™ Hand Climber and Alpha™ Sit and Climb.


32




Step 2: Then, push the hinge forwardto the end of the slot.

First, install the climber base. Step 1: Loosen the torque knobs andpull the hinge washer inward.

Step 3: Re-tighten the knobs.

Lone Wolf Climber PLATFORM InstallationApplicable to Alpha™ Hand Climber and Alpha™ Sit and Climb.


33




Step 6: Place around the tree. Adjustthe stand platform slightly higher on thefront end.

Step 5: Pull the belt from the tube.

Step 7: Insert the belt back into thetube. NOTE: WARNING- point of arrowmarks the end of the belt. No part of thearrow should be showing after the camsare engaged. Failure to follow theseinstructions could cause belt to disengageand cam to open. Now re-attach thecams firmly.

Step 4: Unlatch the cam.


Lone Wolf Climber PLATFORM Installation continued

Applicable to Alpha™ Hand Climber and Alpha™ Sit and Climb.

34




Lone Wolf Climber TOP SECTION InstallationApplicable to Alpha™ Hand Climber and Alpha™ Sit and Climb.

Step 1A: For the HAND CLIMBER flipthe tubes over so they rest on the side ofthe seat casting.

Step 1B: For the SIT AND CLIMB,loosen the torque knobs.

Step 2: Pull the hinge washer inward. Step 3: Push the hinge forward to theend of the slot.


35




Step 4: Retighten the knobs. Now, youare ready to put your top section ontothe tree.

Step 5: Unlatch the cam and pull thebelt from the tube.

Step 6: Place the belt around the tree and insert into the tube. NOTE: WARNING- Point of arrow marks the end of the belt. No part of the arrowshould be showing after the cams are engaged. Failure to follow the instructionsmay cause belt to disengage and cam to open.

Lone Wolf Climber TOP SECTION Installation continued



36




Step 7: Now re-attach your cam firmly. Step 8: Connect your stabilizer straps.WARNING- the stabilizer straps must beconnected before leaving the ground andmust always remain connected while thetreestand is in use.

Lone Wolf Climber TOP SECTION Installation continued



37




Climbing Instructions – Alpha™ Hand Climber

Step 1: Harness to tree. Step 2: Support your weight onto theclimbing aid.

Step 3: Place your feet under thehinges and the bar as shown. Applyslight pressure to the hinge with theinside of the foot.

Step 4: Bend at the knees to disengage stand.


Step 5: Keeping one foot under thehinge bar, step back onto the center ofthe stand with the other to secure it inplace.

Step 6: Slide the harness rope up thetree to the appropriate height.

38




Step 5: Keeping one foot under thehinge bar, step back onto the center ofthe stand with the other to secure it inplace.

Step 6: Slide the harness rope up thetree to the appropriate height.

Step 7: Disengage the climbing aid,raise, and repeat the process.

Step 8: When you reach your desiredheight or when the platform becomeslevel, adjust your harness rope height to it is tight while in a sitting position.Now while in a sitting position pull yourstabilizing straps tight.

Climbing Instructions – Alpha™ Hand Climber continued


39







Climbing Instructions – Alpha™ Sit & Climb

Step 1: Step into center of from. Attachharness rope to tree and lift into postionto climb.

Step 2: Distribute your weight ontoclimbing aid. Place feet under hinge andbar as shown. NOTE: Flip foam seat padover one time, this will hold the seat inupright position.

Step 3: Apply slight pressure to hingewith inside of foot. Bend at knees to disengage stand.

Step 4: Pull stand up with legs. Re-engage stand by shifting weight to heels.Slide harness rope up tree to appropriateheight. Stand up and repeat process.


40




Step 1: Fold the stand and seat downflat placing the two bolt heads into thestabilizer channel as shown.

Step 2: Lay the top section of the HandClimber on top of the platform.

Step 3: Install the bungee cord and stabilizer straps as shown.

Alpha™ Hand Climber Back Packing Instructions


41




Step 4: Criss cross stab straps. Step 5: This is the proper position forthe Hand Climber to be back packed.

Alpha™ Hand Climber Back Packing Instructions continued


42




Step 1: The traction belts should beretracted into the tubes as far as possi-ble with the cams in the locked position.

Step 2: Fold the top and bottom flatand place the top upside down.

Step 3: Place the Sit and Climb barbetween the teeth and traction belt.

Step 4: Lay the bar on 2 points of theteeth.

Alpha™ Sit and Climb Back Packing Instructions


43




Step 8: This is the proper position forback packing the Sit and Climb.

Step 5: Install the bungee cord andstabilizer straps as shown.

Step 7: Criss-cross and connect thestabilizer straps. Pull them tight.

Alpha™ Sit and Climb Back Packing Instructions continued


44

Lone Wolf Alpha™ Ladder Stand








45




Lone Wolf Alpha™ Ladder Standcontinued

LONE WOLF LADDER STAND (ALS16)

Step 1: Attach the offset bracket to theseat post as shown. The offset bracketshould be on the opposite side of theversa button.

Step 2: Tighten the offset bracket so itis secure against the seat post.

46





Step 3: Take your 6 ft. strap and secureone loop off to the clevis pin. Do thiswhile holding the foot leveler in place.

Step 4: Take the strap around the treeattaching the other loop to the oppositeclevis pin and foot leveler.

Step 5: Take the slack out of the strapto secure the base of the ladder forpulling apart the ladder sections.

Step 6: Firmly grab the platform andpull the ladder sections apart to yourdesired height.

47





Step 7: Lock the extended ladder sec-tion in place by inserting 2 clevis pinsper section in the appropriate markedholes. Run the clevis pins from theinside of the ladder rail to the outside.Lock the clevis pins in place.

Step 8: After the ladder sections havebeen pulled apart and secured in placewith the clevis pins, remove the strapfrom the feet levelers and secure the clevis pins back in place.

Step 9: Next, you will install the plat-form support bars. Lift the rear of theplatform up to a level position.

Step 10: Platform support bars shouldbe positioned along the inside of theplatform and ladder rails. Secure themwith the tightening knob.

48





Step 11: Again, the ladder supportbars should be from the inside of the rail placing the clevis pin inside out and locking the pin in place.

Step 12: Repeat the process with theopposite platform support bar.

Step 13: Again, place the support baron the inside of the ladder rail in theappropriately marked hole. Insert the clevis pin from the inside out locking the pin in place.

Step 14: Next, feed the looped end ofthe 16 ft. stabilizer strap through theplatform as shown. Take the otherlooped end, along with the buckle,through the loop. Pull and secure to the platform.

49





Step 15: Then, repeat this process onthe opposite side of the platform. Pulland secure the loop to the platform.

Step 16: With the base of the ladder orthe bottom rung against the base of thetree.

Step 17: Lift the ladder platform tochest height.

Step 18: Press upward over head.

50





Step 19: Walk the ladder up toward the treereaching hand over hand against the rungsuntil the platform connects with the tree.

Step 20: Walk the bottom of the ladderout away from the tree until the ladder isin a free standing position.

Step 21: Installation of the 6 ft stabilizerstraps. Criss-cross the stabilizer strapsaround the back of the tree making surethe straps cross at the highest point pos-sible. Secure them off to the versa but-tons on the ladder sections. Tighten themdown taking the tension out of the straps.

Step 22: When installed properly, theyshould be crossed in the back of the treeas shown.

51





Step 23: Install the black ladder support strap by attaching it to one versa button on one side of the ladderrail, around the tree, securing it off to theopposite versa button on the oppositeside, pulling, and securing the ladder to the tree. Please NOTE: the black 11 ft ladder support strap should be used on the highest versa button that can bereached from the ground or from the firstladder rung.

Step 24: Install the ladder wedge bar.The clamp end of the ladder wedge barshould be placed over the first or secondrung and secured with the clevis pinform the underside of the rung.

Step 25: Remove the clevis pin fromthe adjustment slide in the wedge bar.

Step 26: Slide the bar to a length thatcauses the v-bracket to be in a slightlyhigher position than the clamp end.Then, reinsert the clevis pin to lock thewedge bar at that length.

52





Step 27: Slowly and slightly pull upand out away from the tree on the bottom rung.

Step 28: Before installing your last 2stabilizer straps and before climbing ontothe platform, you must install your treeattachment rope and then your tether to your carabineer.

Step 29: Now you’re ready to installyour last two stabilizing straps. Wrap thebelt around the tree and place the loopover the top versa button. Pull the belttightly.

Step 30: Lastly, install second stabilizerstrap at this time.

53




Lone Wolf Tree Seat





54




THIS IS FOR GROUND USE ONLY. It is not a treestand, nor is it to be used in conjunction with one.

Lone Wolf Tree Seatcontinued

Step 1: Place against the tree and takethe strap around the tree. Place the loopover the versa button and secure it tightly.

Step 2: The leveler bolt under the seatcan be adjusted to your desired position.

55




Lone Wolf Camera Arm

WARNING!Failure to follow these instructions could result in serious injury, death or damage tocamera equipment.

• Do not use camera arm to assist you in entering or exiting you stand.• Do not lean on or against camera arm.• Do not use arm to support your weight.

Using in above fashion could cause arm to become disengaged from tree, resultingin loss of balance or falling out of tree.

• NOTE: Arm is designed for cameras UP TO 6 lbs.

Step 1: Place the camera arm againstthe tree at your desired height. Wrap thebelt around the tree placing the loopover the versa button and pulling tightly.

Step 2: Turn the knob in to tighten thebolt. This will level the arm.

56




This will allow you to properly install theback pack straps to the Alpha™ platform.If you will NOTE there are four smoothribs on the casting of the Alpha™ hangon. This is where you will attach theback pack straps.

Lone Wolf Back Pack StrapsAttachment Instructions

Step 1: Take your back pack strapsand find the fist smooth rib.

Step 2: Go over the top of the bar andkeep the stitching face up.

Step 3: Take the tail of the webbingand run it through and back down againthrough the buckle.

Alpha™ Hang On

57





continued

Alpha™ Hang On: continued

Assault™ Hang On

The Assault™ Hang On uses the sameapplication as the Alpha™ Hang On. Justkeep in mind where the straps will beplaced on the platform.

Step 4: Take the three bar buckle (which is provided) andfeed it through the opposite of the webbing. Keep in mind,you should have 2 bars visible. Find the other smooth rib onthe platform. Go over the top of that rib and back throughone bar of the buckle and then back through the second barof the buckle. This will allow adjustment on both the top andthe bottom. Repeat on the other side.

58




The third application is our accessory padded back pack straps.


continued

Padded Straps

Step 1: Find the smooth rib on thecasting.

Step 2: Go under the rib and throughthe three bar buckle and through theother side.

Step 3: On the bottom, place over the bar, back up to the buckle and through thelower bar of the buckle. Then, go through the top bar of the buckle and cinch tightly.

59




Lone Wolf Climbing SticksAttachment to Stand

for Back Packing( Attaching the Climbing Sticks to the Alpha™ Hang On)

Step 1: To start with, you have twoversa buttons with straps. Start with thelower strap and actually run it around thebase of the stand two times. Run yourloop back over the versa button. Loweryour stand and cinch it tightly.

Step 2: NOTE: There are two foot padsmolded into the platform. Make surethese foot pads are clear from thestraps. We’re going to attach the v-bracket from the sticks there at a later time.

Step 3: Take the Lone Wolf ClimbingStick (keep in mind that on every set ofsticks you will see some webbing with abuckle- always make sure this stick is onthe bottom of your stack).

Step 4: Take the gray webbing andwrap it around the base of the stick.

60






continued

Step 7: Line the allen head up with thathole. You should get a nice, snug fit.

Step 8: Then, take the black webbingon the bottom stick and wrap it aroundthe other two sticks, buckle it, and cinchit tightly.

Step 5: Run the loop back up to theversa button and cinch it tightly. This willkeep everything neat and compact.

Step 6: Take the remaining two sticks(NOTE- the hole on the back of everystick- the hole will line up with the allenhead found on the versa button).

61






continued

Step 9: Then place the top v-bracket in the two impressions on the seat pad. Thetwo foot pads that were mentioned earlier will accommodate the bottom v-bracket.With slight pressure, the two v-brackets should stay in place.

Step 10: Take your second versa buttonand figure eight it around the stand downthe bottom of the base and over the top.

Step 11: Loop the loop over the adjust-ment knob and cinch tightly.

62

For written and video instructionsplease visit www.lonewolfstands.com

See the latest from Lone Wolfat www.lonewolfstands.com

The Wolf Pack™ Lone Wolf Quiver andQuiver Stand Mount

Wolf Jaws™ “Combo” Silent Tote™

Date post:	01-Oct-2020
Category:	Documents
Upload:	others
View:	0 times
Download:	0 times

WARNING! - Lone Wolf Portable Treestands · 2008. 5. 7. · LONE WOLF PORTABLE TREESTANDS PO Box 62...

Documents