Installation Instructions

ZodiaWC Pan, Cistern & Semi Pedestal

521491, 187929, 187930,521494 & 521493

Please note: Images shown are for illustrationpurposes only.

25

2

Contents

Important: the plugs included in this pack are for solid walls only. If the semi pedestal is to be mounted on a partition or stud wall, specialised fixings should be purchased separately.

Caution: Take great care when drilling floors or walls to avoid wires and pipes which may run beneath.Exercise great care when using power tools near water. The use of a residual current device (RCD) or cordless drill is recommended. Always double-check the position and your measurements before drilling holes. Protective eyewear should be used when drilling.

Keep children away from the work area and remember that all small parts, plastic bags and tools should also be kept out of reach of children.

Fixing tip: A piece of insulating tape or a couple of layers of masking tape applied before marking out the fixing holes will help stop the drill from wandering on tiled surfaces.

Fitting InstructionsZodia WC Pan to Floor & Semi Pedestal

Floor/Wall Brackets

S/SteelScrew

NylonBushes

Washer

WallPlug

ChromeCaps

Hex HeadScrew

Method of fixing pan:

hex head screw

chrome caps

pan/semi-ped

floor/wall

washer

bracket

Tighten fixing bracketDrill dia 10mm, approx 40mm fromthe edge of the pan/pedestal.Minimum drill hole depth 60mm

Floor/Wall

Put on the new WC Pan/Pedestal Tighten the screws Put on the chrome caps

Item Description Qty

1

2

3

4

5

6

7

2

2

2

2

2

2

2

Floor/Wall Bracket

Wall Plugs S10 x 50

Hex Head Screw 6 x 60

Washer

S/Steel Screw 5 x 60

Nylon Bushes

Chrome Caps

3

Installation

B7048 / 09.09

PLEASE READ THESE INSTRUCTIONS PRIOR TO INSTALLATION.

These instructions must be carried out in order.

1) Using the checklist underneath, ensure all parts are accounted for and not damaged. Under no circumstances should this product be installed if any of the parts are damaged or missing. If there are any installation issues please contact your local branch.

2) Ensure the gasket is a tight fit on the flush valve thread. Place cistern on the WC so the bolts go through the 2 small holes, add the washers as below and tighten the hex nuts. Please use the spanner if needed. Do not overtighten.

Fitting InstructionsZodia Cistern to WC

Drawing for illustrationpurposes only

1

2

3

4

5

6

4

Item Description Qty

1

2

3

4

5

6

2

2

2

4

2

1

S.Steel Bolt

Rubber Cone Washer

Rubber Washer

Steel Washer

Steel Hex Nut

EPDM Gasket

Installing the Push Button

Take off nut

Install push button with tank cover.

Half flush blue control (semi circle)

Full flush white control (full circle)

Nut

Nut

Enlarge01

01

Rod

Full flush push button

Half flush push button

Left Right

Adjust push button clockwise or anti-clockwise to ensure that the half flush rod is aligned with the blue flush valve control and the full flush rod is aligned with the white flush valve control.

Loosen the fixing nut and rotate rod clockwise or anti-clockwise until the rod end makes contact with the push control then re-tighten the fixing nut (if required cut the upper ends of rods using pliers).

1 2

3

4

Adjusting the Flush to 4/2.6L

Half flush move to mark 2.5(6/4L setting is mark 1)

Full flush move to mark 11 (to the top)(6/4L setting is mark 2)

Fix water cup on mark 1(6/4L setting is mark 2)

Pull the cylinder to the 17th block(count from bottom), 2 blocks above mark 10(6/4L setting is mark 11)

FLUSH VALVE

Please note, factory setting of the cistern inlets is 6/4L flush. The instructions below are showing how to achieve ECO flush of 4/2.6L.

INLET VALVE

Customer Support:We have taken great care to ensure that this product reaches you in perfect condition. However, should any parts be damaged or missing please contact your local branch. This does not affect your statutory rights. In addition if you require replacement parts, your local branch will be only to happy to assist.

JB69087 10/12

Installation Instructions

ZodiaWC Pan, Cistern & Semi Pedestal

521491, 187929, 187930,521494 & 521493

Please note: Images shown are for illustrationpurposes only.

25

2

Contents

Important: the plugs included in this pack are for solid walls only. If the semi pedestal is to be mounted on a partition or stud wall, specialised fixings should be purchased separately.

Caution: Take great care when drilling floors or walls to avoid wires and pipes which may run beneath.Exercise great care when using power tools near water. The use of a residual current device (RCD) or cordless drill is recommended. Always double-check the position and your measurements before drilling holes. Protective eyewear should be used when drilling.

Keep children away from the work area and remember that all small parts, plastic bags and tools should also be kept out of reach of children.

Fixing tip: A piece of insulating tape or a couple of layers of masking tape applied before marking out the fixing holes will help stop the drill from wandering on tiled surfaces.

Fitting InstructionsZodia WC Pan to Floor & Semi Pedestal

Floor/Wall Brackets

S/SteelScrew

NylonBushes

Washer

WallPlug

ChromeCaps

Hex HeadScrew

Method of fixing pan:

hex head screw

chrome caps

pan/semi-ped

floor/wall

washer

bracket

Tighten fixing bracketDrill dia 10mm, approx 40mm fromthe edge of the pan/pedestal.Minimum drill hole depth 60mm

Floor/Wall

Put on the new WC Pan/Pedestal Tighten the screws Put on the chrome caps

Item Description Qty

1

2

3

4

5

6

7

2

2

2

2

2

2

2

Floor/Wall Bracket

Wall Plugs S10 x 50

Hex Head Screw 6 x 60

Washer

S/Steel Screw 5 x 60

Nylon Bushes

Chrome Caps

3

Installation

B7048 / 09.09

PLEASE READ THESE INSTRUCTIONS PRIOR TO INSTALLATION.

These instructions must be carried out in order.

1) Using the checklist underneath, ensure all parts are accounted for and not damaged. Under no circumstances should this product be installed if any of the parts are damaged or missing. If there are any installation issues please contact your local branch.

2) Ensure the gasket is a tight fit on the flush valve thread. Place cistern on the WC so the bolts go through the 2 small holes, add the washers as below and tighten the hex nuts. Please use the spanner if needed. Do not overtighten.

Fitting InstructionsZodia Cistern to WC

Drawing for illustrationpurposes only

1

2

3

4

5

6

4

Item Description Qty

1

2

3

4

5

6

2

2

2

4

2

1

S.Steel Bolt

Rubber Cone Washer

Rubber Washer

Steel Washer

Steel Hex Nut

EPDM Gasket

Installing the Push Button

Take off nut

Install push button with tank cover.

Half flush blue control (semi circle)

Full flush white control (full circle)

Nut

Nut

Enlarge01

01

Rod

Full flush push button

Half flush push button

Left Right

Adjust push button clockwise or anti-clockwise to ensure that the half flush rod is aligned with the blue flush valve control and the full flush rod is aligned with the white flush valve control.

Loosen the fixing nut and rotate rod clockwise or anti-clockwise until the rod end makes contact with the push control then re-tighten the fixing nut (if required cut the upper ends of rods using pliers).

1 2

3

4

Adjusting the Flush to 4/2.6L

Half flush move to mark 2.5(6/4L setting is mark 1)

Full flush move to mark 11 (to the top)(6/4L setting is mark 2)

Fix water cup on mark 1(6/4L setting is mark 2)

Pull the cylinder to the 17th block(count from bottom), 2 blocks above mark 10(6/4L setting is mark 11)

FLUSH VALVE

Please note, factory setting of the cistern inlets is 6/4L flush. The instructions below are showing how to achieve ECO flush of 4/2.6L.

INLET VALVE

Customer Support:We have taken great care to ensure that this product reaches you in perfect condition. However, should any parts be damaged or missing please contact your local branch. This does not affect your statutory rights. In addition if you require replacement parts, your local branch will be only to happy to assist.

JB69087 10/12

4

6

9 10 11

4.Before attaching the seat, move mounting bases so posts align with holes in the back of the seat. Once aligned, carefully lower the seat (holes) onto the mounting post.

11.To remove the seat, press the quick-release button (should hear a "click") and open seat to vertical position, then lift the seat straight up with one hand.

9.When mounting the seat make sure the posts align with holes in the back of seat. And carefully lower seat back into place("click" will heard).Note: Do not push hard or force seat onto posts. (If difficult, re-check alignment.)

* Please keep the products you buy to avoid improper storage (such as loss of accessories, etc.) affect the use of various functions of seat & cover.

88324

Attention: Be careful the damage of toilet seat.Don’t stand on the toilet seat,overloading may leadto toilet seat crushing or hinges broken.

Installation Instruction

Maintenances and Cautions

Instructions for the user

Do not force closure of the seat or lid, allow mechanism to close naturally.

Installation Instruction

Regular maintenance

Please clean the toilet seat with mild cleanser (such as soapwater) and warm water,then dry it with clean soft cloth.

Please immediately wipe dry any foam on the surface of plastictoilet seat or electroplating cover.

Please do not put heavy thingson the seat cover or suddenlysit forcefully on the seat,whichmay lead to the toilet seat crack.

Please do not expose the toiletseat directly to the sunlight foralong time.Avoid any stronglights and high temperature.

Please do not clean the toiletseat with strong chemicalcleanser or stiff brush.

Please do not close the seat orcover forcibly,which may lead tosoft close function lose efficacy,affect your normal using.

Don’t clean the toilet seat with abrasive powder.

Avoid using any disinfector,detergent or any other sprayingcleanser

Keep the toilet seat away from chemicals and cosmetics inbathroom.

Don’t use the high-concentration detergent to clean,which mayscratch the surface of the toilet seat and make the toilet seat tarnish.

Detergent

Cautions