document.xls 文档密级:
04/17/2023 华为机密,未经许可不得扩散 第1页,共66页
1
2
3
Item
document.xls 文档密级:
04/17/2023 华为机密,未经许可不得扩散 第2页,共66页
Draft was completed.
Description
1、Note:.sheet E/// Whether TMA used or not, PCPICHPower and MaxTxPower use the same function.2、Line 38~39 and 54~55,Mapping with E///, TimeToTrig2D/TimeToTrig2F use Min(timeToTrigger2dEcno,timeToTrigger2dRscp)and Min(timeToTrigger2fEcno,timeToTrigger2fRscp)
1、Line 277~288 HSPA parameters added;2、Line 5: column W/AC HopiIdentifier monified to HopgIdentifier。3、Line 57~Line 68 "WCEL > the RtFmcsIdentifier value > the FMCS value > the GSMcauseCPICHEcNo valueIf the NSN value is 0, use the value -24. " is modified to "WCEL > the RtFmcsIdentifier value > the FMCG value > the GSMcauseCPICHEcNo valueIf the NSN value is 0, use the value -24. "4、Line 84: column Q,W,AC,AI modified to "Use the XXX Value".
document.xls 文档密级:
04/17/2023 华为机密,未经许可不得扩散 第3页,共66页
V1.00 Huang Xiangrong 2011.07.30
v1.01 Huang Xiangrong 2011.08.12
v1.02
Huang Xiangrong
2011.10.25
Version Author Date Remarks
document.xls 文档密级:
04/17/2023 华为机密,未经许可不得扩散 第4页,共66页
URFSTG00571 - Huawei WCDMA BSC6900V900R013 Vs Ericsson W10/NSN RU10/NSN RU20/AL UA5.1
1
2
3
For parameters for which this document does not provide mapping analysis, see the Baseline Parameter Values. Using other vendors' parameters values may not optimize Huawei network settings because Huawei algorithms are different from other vendors' algorithms. For values of Compressed Mode Start Threshold for Inter-Frequency, Compressed Mode End Threshold for Inter-Frequency, Compressed Mode Start Threshold for Inter-RAT, Compressed Mode End Threshold for Inter-RAT, and HCS, see the Guide to UMTS Swapping. For values for parameters realted to the multi-carrier policy, see the UMTS R12 Multi-Frequency Band and Multi-Carrier Performance Solution.
Notes about mapping:
Algorithm-related parameters for which this document does not provide mapping analysis, refer to Huawei baseline values.
Some of other vendors' values can be used directly while some values must be multiplied, divided, added, or subtracted before they can be used.
For values for network-related parameters for which this document has provided mapping analysis, refer to the actual values in the live network. For example, for the values for PCPICH Transmit Power and Max Transmit Power of Cell, check whether the (top of cabinet)TOC power or antenna power is used. Huawei uses the TOC power and therefore other vendors' values can be used they also use the TOC power. If other vendors do not use the TOC power, add the feeder loss.
Notes about priority definition:
document.xls 文档密级:
04/17/2023 华为机密,未经许可不得扩散 第5页,共66页
Principle:1. The parameters related to cell reselction initiated by UEs in idle mode, idle mode-related timers, connected mode-related timers, power control, soft handovers, inter-frequency handovers, inter-RAT handovers, and state transition have a high mapping priority. Therefore, Huawei personnel must focus on these parameters during parameter mapping.2. Compared with the Huawei inter-RAT handover mechanism, the NSN inter-RAT handover mechanism triggers more inter-RAT handovers. For details, see the following description. Therefore, Huawei personnel must inform custoers that the number of inter-RAT handovers may decrease after swapping. If customers request that the Huawei inter-RAT handover mechanism opearte in the same way as the NSN inter-RAT handover mechanism, Huawei personnel can raise the 2D or 2F threshold by 1 to 2 dB.The Ericsson inter-RAT handover mechanism is triggered by events while the Huawei inter-RAT handover mechanism is triggered by periodical measurement results. In this case, the Ericsson inter-RAT handover mechanism triggers less inter-RAT handovers than the Huanwei inter-RAT handover mechanism. This leads to decreased CS traffic in 3G cells and the increased number of inter-RAT handovers after swapping. If customers request that the Huawei inter-RAT handover mechanism opearte in the same way as the Ericsson inter-RAT handover mechanism, Huawei personnel can lower the 2D or 2F threshold by 1 to 2 dB.
To find appropriate values for PCPICH Transmit Power and Max Transmit Power of Cell, first check whether some TMAs are used. To do this, check the value for ulGain. If the value is 0, no TMAs are used. Otherwise, some TMAs may be in useIf some TMAs are used, use the following formula to calculate values for the preceding two parameters:MaxTxPower (HUAWEI) = maximumTransmissionPower + dlAttenuation(ExternalTma) + dlAttenuation(AntFeederCable) (Ericsson) PCPICHPower (HUAWEI) = primaryCpichPower + dlAttenuation(ExternalTma) + dlAttenuation(AntFeederCable) (Ericsson)If no TMAs are used, use Ericsson vlaues since Ericsson also uses the TOC power.Notes:The ulGain parameter is a NodeB-level parameter and thefore dump documents can be obtained only on a PLMN basis. After this, all RNC and NodeB parameters can be obtained.The following figure shows a base station where a TMA is used:
document.xls 文档密级:
04/17/2023 华为机密,未经许可不得扩散 第6页,共66页
Ericsson calculates the maximum transmit power of a radio link in the following way:For the RL Max DL TX power parameter, calculate the value for different sevices based on the following scripts and figure:Radio Connection Type Maximum DL Radio Link Rate MaxPower PS384/HS 3700 0 SRB 13.6 14800 0 AMR 12.2 15900 0 CS64 67700 32 PS64/64 70900 34 MultiRAB (CS64 + PS8/8) 76100 37 PS64/384 406900 48Note that parameter values in the preceding scripts are just examples, and therefore onsite personnel must check which values are used in Ericsson scripts and then calculate the value for RL Max DL TX power for different services.For example, the maximum downlink radio link rate is 67700 for the CS64 service. In addition, InterRate is set to 77600, interPwrMax is set to 38, MinimunRate is set to 15900, and minPwrMax is set to 0. Then, according to the following formula, the RL Max DL TX power parameter for this services must be set to 31.9:RL Max DL TX power = (interPwrMax-minPwrMax)/(InterRate - MinimunRate)x(Maximum DL Radio Link Rate - MinimunRate)
The NSN inter-RAT handover measurement mechanism operates in the following way:During the inter-RAT handover measurement procedure, the RNC determines whether to enable UEs to stop being in compressed mode after event 1E is reported based on the values for ISHOCancellation, ISHOClcauseCPICHEcNo, ISHOClcauseCPICHrscp, and MaxNumISHOClPerAS.For example, the RNC enables a UE to stop being in compressed mode after event 1E is reported when the following three conditions are met:1. MaxNumISHOClPerAS is set to 1 or a smaller value.2. ISHOCancellation is set to Enabled.3. ISHOClcauseCPICHEcNo is set to Enabled or ISHOClcauseCPICHrscp is set to Enabled.However, the Huawei algorithm neables a UE to stop being in compressed mode after event 2F is reported. Compared with the Huawei inter-RAT handover measurement mechanism, the NSN inter-RAT handover measurement mechanism triggers more inter-RAT handovers.
document.xls 文档密级:
04/17/2023 华为机密,未经许可不得扩散 第7页,共66页
Cancellation of inter-system handover because of event 1EThe RNC stops inter-system measurements when event 1E occurs for at least one cellof the active set. Event 1E can be configured for the following measurements on thePrimary CPICH:• CPICH RSCP: received signal code power (RSCP)• CPICH Ec/No: received energy per chip divided by the power density in the band,that is CPICH RSCP/UTRA Carrier RSSIThe parameters ISHOClcauseCPICHEcNo and/or ISHOClcauseCPICHrscp indicatewhether inter-system measurement cancellation in the UE is enabled or not for situationswhen a primary CPICH (active set cell) increases beyond the absolute threshold(Event 1E).
Inter-System handover cancellation because of measurement event 1E can be performedonly when all of the following conditions are met:• The Inter-System Handover Cancellation feature is enabled by theISHOCancellation parameter.
• The ISHOClcauseCPICHEcNo or ISHOClcauseCPICHrscp parameter has beenset to ‘enabled’ for one or more cells in the active set.
• The number of inter-system cancellations that have been performed for the correspondingUE with the current active set is less than the value specified for theMaxNumISHOClPerAS parameter.
• Inter-System measurements were started in the UE because of event 1F (for CPICHEc/No or CPICH RSCP) triggered measurement report.• Event 1E triggered measurement report was received during inter-system measurementphase.
document.xls 文档密级:
04/17/2023 华为机密,未经许可不得扩散 第8页,共66页
URFSTG00571 - Huawei WCDMA BSC6900V900R013 Vs Ericsson W10/NSN RU10/NSN RU20/AL UA5.1
For parameters for which this document does not provide mapping analysis, see the Baseline Parameter Values. Using other vendors' parameters values may not optimize Huawei network settings because Huawei algorithms are different from other vendors' algorithms. For values of Compressed Mode Start Threshold for Inter-Frequency, Compressed Mode End Threshold for Inter-Frequency, Compressed Mode Start Threshold for Inter-RAT, Compressed Mode End Threshold for Inter-RAT, and HCS, see the Guide to UMTS Swapping. For values for parameters realted to the multi-
UMTS R12 Multi-Frequency Band and Multi-Carrier Performance Solution.
Algorithm-related parameters for which this document does not provide mapping analysis, refer to
Some of other vendors' values can be used directly while some values must be multiplied, divided, added, or subtracted before they can be used.
For values for network-related parameters for which this document has provided mapping analysis, refer to the actual values in the live network. For example, for the values for PCPICH Transmit Power and Max Transmit Power of Cell, check whether the (top of cabinet)TOC power or antenna power is used. Huawei uses the TOC power and therefore other vendors' values can be used they also use the TOC power. If other vendors do not use the TOC power, add the
document.xls 文档密级:
04/17/2023 华为机密,未经许可不得扩散 第9页,共66页
1. The parameters related to cell reselction initiated by UEs in idle mode, idle mode-related timers, connected mode-related timers, power control, soft handovers, inter-frequency handovers, inter-RAT handovers, and state transition have a high mapping priority. Therefore, Huawei
2. Compared with the Huawei inter-RAT handover mechanism, the NSN inter-RAT handover mechanism triggers more inter-RAT handovers. For details, see the following description. Therefore, Huawei personnel must inform custoers that the number of inter-RAT handovers may decrease after swapping. If customers request that the Huawei inter-RAT handover mechanism opearte in the same way as the NSN inter-RAT handover mechanism, Huawei personnel can raise the 2D or 2F threshold by 1 to 2 dB.The Ericsson inter-RAT handover mechanism is triggered by events while the Huawei inter-RAT handover mechanism is triggered by periodical measurement results. In this case, the Ericsson inter-RAT handover mechanism triggers less inter-RAT handovers than the Huanwei inter-RAT handover mechanism. This leads to decreased CS traffic in 3G cells and the increased number of inter-RAT handovers after swapping. If customers request that the Huawei inter-RAT handover mechanism opearte in the same way as the Ericsson inter-RAT handover mechanism,
Max Transmit Power of Cell, first check whether some TMAs are used. To do . If the value is 0, no TMAs are used. Otherwise, some TMAs may be in use
If some TMAs are used, use the following formula to calculate values for the preceding two parameters:MaxTxPower (HUAWEI) = maximumTransmissionPower + dlAttenuation(ExternalTma) + dlAttenuation(AntFeederCable) (Ericsson) PCPICHPower (HUAWEI) = primaryCpichPower + dlAttenuation(ExternalTma) + dlAttenuation(AntFeederCable) (Ericsson)If no TMAs are used, use Ericsson vlaues since Ericsson also uses the TOC power.
The ulGain parameter is a NodeB-level parameter and thefore dump documents can be obtained only on a PLMN basis. After this, all RNC and
document.xls 文档密级:
04/17/2023 华为机密,未经许可不得扩散 第10页,共66页
Ericsson calculates the maximum transmit power of a radio link in the following way: parameter, calculate the value for different sevices based on the following scripts and figure:
Radio Connection Type Maximum DL Radio Link Rate MaxPower
Note that parameter values in the preceding scripts are just examples, and therefore onsite personnel must check which values are used in for different services.
For example, the maximum downlink radio link rate is 67700 for the CS64 service. In addition, InterRate is set to 77600, interPwrMax is set to . Then, according to the following formula, the RL Max DL TX power parameter
RL Max DL TX power = (interPwrMax-minPwrMax)/(InterRate - MinimunRate)x(Maximum DL Radio Link Rate - MinimunRate)
The NSN inter-RAT handover measurement mechanism operates in the following way:During the inter-RAT handover measurement procedure, the RNC determines whether to enable UEs to stop being in compressed mode after
ISHOClcauseCPICHEcNo, ISHOClcauseCPICHrscp, and
For example, the RNC enables a UE to stop being in compressed mode after event 1E is reported when the following three conditions are met:
is set to Enabled.However, the Huawei algorithm neables a UE to stop being in compressed mode after event 2F is reported. Compared with the Huawei inter-RAT handover measurement mechanism, the NSN inter-RAT handover measurement mechanism triggers more inter-RAT handovers.
document.xls 文档密级:
04/17/2023 华为机密,未经许可不得扩散 第11页,共66页
The RNC stops inter-system measurements when event 1E occurs for at least one cellof the active set. Event 1E can be configured for the following measurements on the
CPICH Ec/No: received energy per chip divided by the power density in the band,
The parameters ISHOClcauseCPICHEcNo and/or ISHOClcauseCPICHrscp indicatewhether inter-system measurement cancellation in the UE is enabled or not for situationswhen a primary CPICH (active set cell) increases beyond the absolute threshold
Inter-System handover cancellation because of measurement event 1E can be performed
The ISHOClcauseCPICHEcNo or ISHOClcauseCPICHrscp parameter has been
The number of inter-system cancellations that have been performed for the corresponding
Inter-System measurements were started in the UE because of event 1F (for CPICH
Event 1E triggered measurement report was received during inter-system measurement
document.xls 文档密级:
04/17/2023 华为机密,未经许可不得扩散 第12页,共66页
NE Parameter Type
RNC CELL Inter RNC Cell Update
RNC CELL
RNC CELL
RNC CELL
RNC CELL
RNC CELL
RNC CELL
RNC CELL
RNC CELL
RNC CELL Access Class Restriction
RNC CELL Access Class Restriction
RNC CELL Access Class Restriction
RNC CELL Access Class Restriction
RNC CELL Access Class Restriction
RNC CELL Access Class Restriction
RNC CELL Access Class Restriction
RNC CELL Access Class Restriction
RNC CELL Access Class Restriction
RNC CELL Access Class Restriction
RNC CELL Access Class Restriction
RNC CELL Access Class Restriction
RNC CELL Access Class Restriction
RNC CELL Access Class Restriction
RNC CELL Access Class Restriction
RNC CELL Access Class Restriction
RNC CELL Access Class Restriction
Cell-Level or RNC-Level
Intra RNC Cell UpdateInter RNC Cell UpdateOpen Loop Power ControlOpen Loop Power ControlPhysical Channel ManagementPhysical Channel ManagementPhysical Channel ManagementIntra Node B Softer HandoverOpen Loop Power Control
document.xls 文档密级:
04/17/2023 华为机密,未经许可不得扩散 第13页,共66页
RNC CELL Access Class Restriction
RNC CELL Access Class Restriction
RNC CELL Access Class Restriction
RNC CELL
RNC CELL HSDPA Power Control
RNC CELL
RNC CELL
RNC CELL
RNC CELL
RNC CELL
RNC CELL
RNC CELL
RNC CELL
RNC CELL
RNC CELL
RNC CELL
RNC CELL
RNC CELL
RNC CELL
RNC CELL
RNC CELL
RNC CELL
RNC CELL
RNC CELL
RNC CELL
RNC CELL
RNC CELL
RNC CELL
Admission ControlLoad Measurement
Inter Frequency Hard Handover Based on CoverageInter Frequency Hard Handover Based on CoverageInter Frequency Hard Handover Based on CoverageInter Frequency Hard Handover Based on CoverageInter Frequency Hard Handover Based on CoverageInter Frequency Hard Handover Based on CoverageInter Frequency Hard Handover Based on CoverageInter Frequency Hard Handover Based on CoverageInter Frequency Hard Handover Based on CoverageInter Frequency Hard Handover Based on CoverageInter Frequency Hard Handover Based on CoverageInter Frequency Hard Handover Based on CoverageInter Frequency Hard Handover Based on CoverageInter Frequency Hard Handover Based on CoverageInter Frequency Hard Handover Based on CoverageInter Frequency Hard Handover Based on CoverageInter Frequency Hard Handover Based on CoverageInter-RAT Handover Based on CoverageInter-RAT Handover Based on CoverageInter-RAT Handover Based on CoverageInter-RAT Handover Based on CoverageInter-RAT Handover Based on Coverage
Inter-RAT Handover Based on Coverage
document.xls 文档密级:
04/17/2023 华为机密,未经许可不得扩散 第14页,共66页
RNC CELL
RNC CELL
RNC CELL
RNC CELL
RNC CELL
RNC CELL
RNC CELL
RNC CELL
RNC CELL
RNC CELL
RNC CELL
RNC CELL
RNC CELL
RNC CELL
RNC CELL
RNC CELL
RNC CELL
RNC CELL
RNC CELL
RNC CELL
RNC CELL None
RNC CELL None
RNC CELL
RNC CELL
RNC CELL
Inter-RAT Handover Based on Coverage
Inter-RAT Handover Based on Coverage
Inter-RAT Handover Based on Coverage
Inter-RAT Handover Based on Coverage
Inter-RAT Handover Based on Coverage
Inter-RAT Handover Based on Coverage
Inter-RAT Handover Based on CoverageInter-RAT Handover Based on Coverage
Inter-RAT Handover Based on CoverageInter-RAT Handover Based on CoverageInter-RAT Handover Based on CoverageInter-RAT Handover Based on CoverageInter-RAT Handover Based on CoverageInter-RAT Handover Based on CoverageIntra Node B Softer HandoverIntra Node B Softer HandoverIntra Node B Softer HandoverIntra Node B Softer HandoverIntra Node B Softer HandoverIntra Node B Softer Handover
Intra Node B Softer HandoverIntra Node B Softer HandoverIntra Node B Softer Handover
document.xls 文档密级:
04/17/2023 华为机密,未经许可不得扩散 第15页,共66页
RNC CELL
RNC CELL
RNC CELL
RNC CELL
RNC CELL
RNC CELL
RNC CELL
RNC CELL
RNC CELL
RNC CELL
RNC CELL
RNC CELL
RNC CELL
RNC CELL
RNC RNC 3GPP Specifications
RNC RNC
RNC RNC 3GPP Specifications
RNC RNC
RNC RNC 3GPP Specifications
RNC RNC 3GPP Specifications
RNC RNC 3GPP Specifications
RNC RNC 3GPP Specifications
RNC RNC 3GPP Specifications
RNC RNC 3GPP Specifications
RNC RNC 3GPP Specifications
RNC RNC 3GPP Specifications
RNC RNC 3GPP Specifications
RNC RNC 3GPP Specifications
RNC CELL
Intra Node B Softer HandoverIntra Node B Softer HandoverIntra RNC Cell UpdateInter RNC Cell UpdateIntra RNC Cell UpdateInter RNC Cell UpdateIntra RNC Cell UpdateInter RNC Cell UpdateIntra RNC Cell UpdateInter RNC Cell UpdateIntra RNC Cell UpdateInter RNC Cell UpdateIntra RNC Cell UpdateInter RNC Cell UpdateIntra RNC Cell UpdateInter RNC Cell UpdateIntra RNC Cell UpdateInter RNC Cell UpdateIntra RNC Cell UpdateInter RNC Cell UpdateIntra RNC Cell UpdateInter RNC Cell UpdateOpen Loop Power ControlOpen Loop Power Control
Connection with TMA (Tower Mounted Amplifier)
System Information Broadcasting
Inter-RAT Handover Based on Coverage
document.xls 文档密级:
04/17/2023 华为机密,未经许可不得扩散 第16页,共66页
RNC CELL
RNC CELL
RNC CELL
RNC CELL
RNC CELL
RNC CELL None
RNC CELL
RNC RNC
RNC RNC
RNC RNC 3GPP Specifications
RNC RNC 3GPP Specifications
RNC RNC 3GPP Specifications
RNC RNC 3GPP Specifications
RNC RNC
RNC RNC
RNC RNC
RNC RNC
RNC RNC
RNC RNC
RNC RNC
RNC RNC
RNC RNC
RNC RNC
RNC RNC
RNC RNC
RNC RNC
RNC RNC
RNC RNC
Intra RNC Cell UpdateInter RNC Cell UpdateIntra RNC Cell UpdateInter RNC Cell UpdateInter RNC Soft HandoverDirect Signaling Connection Re-establishment (DSCR)Inter RNC Soft HandoverDirect Signaling Connection Re-establishment (DSCR)Intra Node B Softer Handover
Open Loop Power ControlInner Loop Power ControlPaging UE in Idle, CELL_PCH, URA_PCH State (Type 1)
Inter Frequency Hard Handover Based on CoverageInter Frequency Hard Handover Based on CoverageInter Frequency Hard Handover Based on CoverageInter Frequency Hard Handover Based on CoverageInter Frequency Hard Handover Based on CoverageInter Frequency Hard Handover Based on CoverageInter Frequency Hard Handover Based on CoverageInter Frequency Hard Handover Based on CoverageInter Frequency Hard Handover Based on CoverageInter Frequency Hard Handover Based on CoverageInter Frequency Hard Handover Based on CoverageInter Frequency Hard Handover Based on CoverageInter Frequency Hard Handover Based on CoverageInter Frequency Hard Handover Based on CoverageInter Frequency Hard Handover Based on Coverage
document.xls 文档密级:
04/17/2023 华为机密,未经许可不得扩散 第17页,共66页
RNC RNC
RNC RNC
RNC CELL
RNC CELL
RNC CELL
RNC CELL Inter RNC Cell Update
RNC CELL Inter RNC Cell Update
RNC RNC
RNC RNC
RNC RNC
RNC RNC
RNC RNC
RNC RNC
RNC RNC
RNC RNC
RNC RNC
RNC RNC
RNC RNC
RNC RNC
RNC RNC
RNC RNC
RNC RNC
RNC RNC
RNC RNC
RNC RNC
RNC RNC
RNC RNC
RNC RNC
RNC RNC
Inter Frequency Hard Handover Based on CoverageInter Frequency Hard Handover Based on CoverageIntra Node B Softer HandoverIntra RNC Cell UpdateInter RNC Cell UpdateIntra RNC Cell UpdateInter RNC Cell Update
Inter-RAT Handover Based on CoverageInter-RAT Handover Based on CoverageInter-RAT Handover Based on CoverageInter-RAT Handover Based on CoverageInter-RAT Handover Based on CoverageInter-RAT Handover Based on CoverageInter-RAT Handover Based on CoverageInter-RAT Handover Based on CoverageInter-RAT Handover Based on CoverageInter-RAT Handover Based on CoverageInter-RAT Handover Based on CoverageInter-RAT Handover Based on CoverageInter-RAT Handover Based on CoverageInter-RAT Handover Based on CoverageInter-RAT Handover Based on CoverageInter-RAT Handover Based on CoverageInter-RAT Handover Based on CoverageInter-RAT Handover Based on CoverageInter-RAT Handover Based on CoverageIntra Node B Softer HandoverIntra Node B Softer HandoverIntra Node B Softer Handover
document.xls 文档密级:
04/17/2023 华为机密,未经许可不得扩散 第18页,共66页
RNC RNC
RNC RNC
RNC RNC
RNC RNC None
RNC RNC None
RNC RNC
RNC RNC
RNC RNC
RNC RNC
RNC RNC
RNC CELL
RNC CELL
RNC CELL
RNC CELL
RNC CELL
RNC CELL
RNC CELL
RNC CELL
RNC CELL
RNC CELL
RNC CELL
RNC CELL
RNC CELL
RNC CELL
RNC CELL
RNC CELL
RNC RNC 3GPP Specifications
RNC RNC 3GPP Specifications
RNC CELL
Intra Node B Softer HandoverIntra Node B Softer HandoverIntra Node B Softer Handover
Intra Node B Softer HandoverIntra Node B Softer HandoverIntra Node B Softer HandoverIntra Node B Softer HandoverIntra Node B Softer HandoverIntra Node B Softer HandoverIntra Node B Softer HandoverIntra Node B Softer HandoverIntra RNC Cell UpdateInter RNC Cell UpdateIntra RNC Cell UpdateInter RNC Cell UpdateOpen Loop Power ControlOpen Loop Power ControlOpen Loop Power ControlOpen Loop Power ControlOpen Loop Power ControlOpen Loop Power ControlOpen Loop Power ControlSystem Information BroadcastingSystem Information BroadcastingSystem Information BroadcastingOpen Loop Power Control
Intra RNC Cell UpdateInter RNC Cell Update
document.xls 文档密级:
04/17/2023 华为机密,未经许可不得扩散 第19页,共66页
RNC CELL
RNC RNC
RNC RNC
RNC RNC
RNC RNC
RNC RNC
RNC RNC
RNC RNC None
RNC RNC
RNC RNC
RNC CELL
RNC CELL
RNC CELL
RNC CELL
RNC CELL
RNC CELL
RNC CELL
RNC CELL
RNC CELL
RNC CELL
RNC CELL None
RNC CELL
RNC CELL
RNC CELL Access Class Restriction
RNC CELL Access Class Restriction
RNC CELL Access Class Restriction
RNC CELL
RNC RNC
RNC RNC
Intra RNC Cell UpdateInter RNC Cell UpdateIntra Node B Softer HandoverIntra Node B Softer HandoverIntra Node B Softer HandoverIntra Node B Softer HandoverIntra Node B Softer HandoverIntra Node B Softer Handover
Intra Node B Softer HandoverIntra Node B Softer HandoverIntra RNC Cell UpdateInter RNC Cell UpdateIntra RNC Cell UpdateInter RNC Cell UpdateIntra RNC Cell UpdateMulti Frequency Band Networking ManagementIntra RNC Cell UpdateMulti Frequency Band Networking ManagementIntra Node B Softer HandoverIntra Node B Softer HandoverIntra Node B Softer HandoverIntra Node B Softer HandoverIntra Node B Softer HandoverIntra Node B Softer Handover
Intra Node B Softer HandoverIntra Node B Softer Handover
Inter-RAT Handover Based on CoverageHSDPA State TransitionHSUPA DCCCHSDPA State TransitionHSUPA DCCC
document.xls 文档密级:
04/17/2023 华为机密,未经许可不得扩散 第20页,共66页
RNC RNC
RNC RNC
RNC RNC
RNC RNC
RNC RNC
RNC RNC
RNC RNC
RNC RNC
RNC RNC
RNC RNC
RNC RNC
RNC RNC
RNC RNC
RNC CELL
RNC CELL
RNC RNC
RNC RNC
RNC RNC
RNC RNC
RNC RNC
RNC RNC
RNC CELL
RNC CELL
RNC CELL
RNC CELL
RNC CELL
RNC CELL
HSDPA State TransitionHSUPA DCCC3.4/6.8/13.6/27.2 kbit/s RRC Connection and RAB Assignment3.4/6.8/13.6/27.2 kbit/s RRC Connection and RAB Assignment3.4/6.8/13.6/27.2 kbit/s RRC Connection and RAB Assignment3.4/6.8/13.6/27.2 kbit/s RRC Connection and RAB AssignmentUE State in Connected Mode (CELL-DCH, CELL-PCH, URA-PCH, CELL-FACH)UE State in Connected Mode (CELL-DCH, CELL-PCH, URA-PCH, CELL-FACH)UE State in Connected Mode (CELL-DCH, CELL-PCH, URA-PCH, CELL-FACH)
UE State in Connected Mode (CELL-DCH, CELL-PCH, URA-PCH, CELL-FACH)UE State in Connected Mode (CELL-DCH, CELL-PCH, URA-PCH, CELL-FACH)UE State in Connected Mode (CELL-DCH, CELL-PCH, URA-PCH, CELL-FACH)UE State in Connected Mode (CELL-DCH, CELL-PCH, URA-PCH, CELL-FACH)UE State in Connected Mode (CELL-DCH, CELL-PCH, URA-PCH, CELL-FACH)Open Loop Power ControlAdmission Control
Open Loop Power ControlInter Frequency Hard Handover Based on CoverageInter Frequency Hard Handover Based on CoverageInter Frequency Hard Handover Based on CoverageInter Frequency Hard Handover Based on CoverageInter Frequency Hard Handover Based on CoverageInter Frequency Hard Handover Based on CoverageInter Frequency Hard Handover Based on CoverageInter Frequency Hard Handover Based on CoverageInter Frequency Hard Handover Based on CoverageInter Frequency Hard Handover Based on CoverageInter Frequency Hard Handover Based on CoverageInter Frequency Hard Handover Based on Coverage
document.xls 文档密级:
04/17/2023 华为机密,未经许可不得扩散 第21页,共66页
RNC CELL
RNC CELL
RNC CELL
RNC CELL None
RNC CELL 3GPP Specifications
RNC CELL None
RNC CELL 3GPP Specifications
RNC CELL
RNC CELL
RNC CELL
RNC CELL
RNC CELL
RNC CELL
RNC CELL
RNC CELL
RNC CELL
RNC CELL
RNC RNC
RNC RNC
RNC RNC
RNC CELL
RNC CELL
RNC CELL
CELL HSUPA
CELL HSUPA
CELL HSUPA
CELL HSUPA
CELL HSUPA
Physical Channel ManagementPhysical Channel Management3GPP SpecificationsShared Network Support in Connected Mode
Intra RNC Cell UpdateInter RNC Cell UpdateIntra RNC Cell UpdateInter RNC Cell UpdateIntra RNC Cell UpdateInter RNC Cell UpdateIntra RNC Cell UpdateInter RNC Cell UpdateIntra RNC Cell UpdateInter RNC Cell UpdateIntra RNC Cell UpdateInter RNC Cell UpdateInter-RAT Handover Based on CoverageInter-RAT Handover Based on DL QoSInter-RAT Handover Based on CoverageInter-RAT Handover Based on CoverageHSDPA Introduction PackageHSDPA Mobility ManagementHSDPA Mobility ManagementHSDPA Mobility ManagementHSUPA Mobility ManagementInter Frequency Hard Handover Based on Coverage
Inter-RAT Handover Based on CoverageInter-RAT Handover Based on Coverage
RNC
RNC
RNC
RNC
RNC
document.xls 文档密级:
04/17/2023 华为机密,未经许可不得扩散 第22页,共66页
CELL HSUPA
CELL HSUPA
CELL
HSUPA
CELL HSUPA
CELLHSUPA
CELL HSUPA
CELL HSUPA
RNC
RNC
RNC
RNC
RNC
RNC
RNC
document.xls 文档密级:
04/17/2023 华为机密,未经许可不得扩散 第23页,共66页
Parameter ID Parameter Name Meaning
Qoffset1sn Qoffset1sn
Qrxlevmin Min RX Level
BCHPower BCH Transmit Power
MaxTxPower
NInsyncInd
NOutsyncInd
TRlFailure
CIO
PCPICHPower
CellReservedForOperatorUse
IsAccessClass0Barred
IsAccessClass1Barred
IsAccessClass2Barred
IsAccessClass3Barred
IsAccessClass4Barred
IsAccessClass5Barred
IsAccessClass6Barred
IsAccessClass7Barred
IsAccessClass8Barred
IsAccessClass9Barred
IsAccessClass10Barred
IsAccessClass11Barred
IsAccessClass12Barred
IsAccessClass13Barred
IsAccessClass14Barred
IsAccessClass15Barred
Offset between the neighboring GSM cell and WCDMA cell.Minimum RX level of the GSM cell.Offset of the BCH transmit power from the PCPICH transmit power in a cell. For detailed
Max Transmit Power of Cell
Sum of the maximum transmit power of all DL channels in a cell. For detailed information of
Num of Continuous in Sync Ind
This parameter defines the times of successive in-sync indications required for the NodeB to
Num of Continuous Out of Sync Ind
This parameter defines the times of successive in-sync indications required for starting the
Radio Link Failure Timer Length
Radio link failure timer duration. When the radio link set is in the synchronized state, the
Cell Oriented Cell Individual Offset
This parameter works with the offset of neighboring cell-oriented Cell Individual Offset
PCPICH Transmit Power
TX power of the PCPICH in a cell. This parameter should be set based on the actual system
Cell reserved for operator use
Indicating whether the cell is reserved for operators. If the status of cell is NOT_BARRED,
Access class 0 barred indicator
Indicating whether the UE allocated with Access Class 0 can be allowed to initiate access to the
Access class 1 barred indicator
Indicating whether the UE allocated with Access Class 1 can be allowed to initiate access to the
Access class 2 barred indicator
Indicating whether the UE allocated with Access Class 2 can be allowed to initiate access to the
Access class 3 barred indicator
Indicating whether the UE allocated with Access Class 3 can be allowed to initiate access to the
Access class 4 barred indicator
Indicating whether the UE allocated with Access Class 4 can be allowed to initiate access to the
Access class 5 barred indicator
Indicating whether the UE allocated with Access Class 5 can be allowed to initiate access to the
Access class 6 barred indicator
Indicating whether the UE allocated with Access Class 6 can be allowed to initiate access to the
Access class 7 barred indicator
Indicating whether the UE allocated with Access Class 7 can be allowed to initiate access to the
Access class 8 barred indicator
Indicating whether the UE allocated with Access Class 8 can be allowed to initiate access to the
Access class 9 barred indicator
Indicating whether the UE allocated with Access Class 9 can be allowed to initiate access to the
Access class 10 barred indicator
Indicating whether the UE allocated with Access Class 10 can be allowed to initiate access to the
Access class 11 barred indicator
Indicating whether the UE allocated with Access Class 11 can be allowed to initiate access to the
Access class 12 barred indicator
Indicating whether the UE allocated with Access Class 12 can be allowed to initiate access to the
Access class 13 barred indicator
Indicating whether the UE allocated with Access Class 13 can be allowed to initiate access to the
Access class 14 barred indicator
Indicating whether the UE allocated with Access Class 14 can be allowed to initiate access to the
Access class 15 barred indicator
Indicating whether the UE allocated with Access Class 15 can be allowed to initiate access to the
document.xls 文档密级:
04/17/2023 华为机密,未经许可不得扩散 第24页,共66页
IdleCellBarred
IdleIntraFreqReselection
IdleTbarred Time barred for SIB3
BackgroundNoise Background noise
HspaPower
PrdReportInterval
HystFor2D 2D Hysteresis
HystFor2F 2F Hysteresis
TimeToTrig2D Event 2D Trigger Delay
TimeToTrig2F Event 2F Trigger Delay
InterFreqCSThd2DEcN0
InterFreqCSThd2FEcN0
InterFreqR99PsThd2DEcN0
InterFreqHThd2DEcN0
InterFreqR99PsThd2FEcN0
InterFreqHThd2FEcN0
InterFreqCSThd2DRSCP
InterFreqCSThd2FRSCP
InterFreqR99PsThd2DRSCP
InterFreqHThd2DRSCP
InterFreqR99PsThd2FRSCP
InterFreqHThd2FRSCP
Hystfor2D 2D Hysteresis
Hystfor2F 2F Hysteresis
TrigTime2D
TrigTime2F
TrigTime3A
InterRATCSThd2DEcN0
Cell barred indicator for SIB3
Indicating whether the UE in idle mode is allowed to access the cell. When the cell status
Intra-freq cell reselection ind for SIB3
Indicating whether the UE in idle mode is allowed to reselect another intra-frequency This parameter is valid when [Cell barred indicator for SIB3] is BARRED. It indicates If [Auto-Adaptive Background Noise Update Switch] is set to OFF, it is used to set
The Offset of HSPA Total Power
This parameter specifies the offset between the total HSPA power and the maximum
Inter-frequency Measure Periodical Measurement Report Period
Interval between periodic reporting for the inter-frequency handover. Hysteresis for triggering event 2D.Hysteresis for triggering event 2F.Interval time between detection of event 2D and sending of the measurement report. Interval time between detection of event 2F and sending of the measurement report.This
Inter-freq CS Measure Start Ec/No THD
Ec/No threshold of triggering the inter-frequency measurement for CS services.
Inter-freq CS Measure Stop Ec/No THD
Ec/No threshold of stopping the inter-frequency measurement for CS services.Inter-freq R99 PS
Measure Start Ec/No THD
Ec/No threshold of triggering the inter-frequency measurement for PS non-HSPA
Inter-freq H Measure Start Ec/No THD
Ec/No threshold of triggering the inter-frequency measurement for HSPA services.Inter-freq R99 PS
Measure Stop Ec/No THD
Ec/No threshold of stopping the inter-frequency measurement for PS non-HSPA
Inter-freq H Measure Stop Ec/No THD
Ec/No threshold of stopping the inter-frequency measurement for HSPA services.
Inter-freq CS Measure Start RSCP THD
RSCP threshold of triggering the inter-frequency measurement for CS services.
Inter-freq CS Measure Stop RSCP THD
RSCP threshold of stopping the inter-frequency measurement for CS services.Inter-freq R99 PS
Measure Start RSCP THD
RSCP threshold of triggering the inter-frequency measurement for PS non-HSPA
Inter-freq H Measure Start RSCP THD
RSCP threshold of triggering the inter-frequency measurement for HSPA services.Inter-freq R99 PS
Measure Stop RSCP THD
RSCP threshold of stopping the inter-frequency measurement for PS non-HSPA
Inter-freq H Measure Stop RSCP THD
RSCP threshold of stopping the inter-frequency measurement for HSPA services.
Hysteresis for event 2D. This parameter is used to avoid the ping-pong reporting of event 2D (the estimated quality of the
Hysteresis for event 2F.The value of this parameter is associated with slow fading. If this parameter is set to a
2D Event Trigger Delay Time
Interval time between detection of event 2D and sending of the measurement report.
2F Event Trigger Delay Time
Interval time between detection of event 2F and sending of the measurement report.
3A Event Trigger Delay Time
Interval time between detection of event 3A and sending of the measurement report.
Inter-RAT CS Measure Start Ec/No THD
Threshold of triggering inter-RAT measurement for CS services when measurement quantity is
document.xls 文档密级:
04/17/2023 华为机密,未经许可不得扩散 第25页,共66页
InterRATCSThd2FEcN0
InterRATR99PsThd2DEcN0
InterRATHThd2DEcN0
InterRATR99PsThd2FEcN0
InterRATHThd2FEcN0
InterRATCSThd2DRSCP
InterRATCSThd2FRSCP
InterRATR99PsThd2DRSCP
InterRATHThd2DRSCP
InterRATR99PsThd2FRSCP
InterRATHThd2FRSCP
TargetRatCsThd
TargetRatR99PsThd
TargetRatHThd
IntraRelThdFor1ACSVP
IntraRelThdFor1ACSNVP
IntraRelThdFor1APS
IntraRelThdFor1BCSVP
IntraRelThdFor1BCSNVP
IntraRelThdFor1BPS
HystFor1A 1A Hysteresis
HystFor1B 1B Hysteresis
HystFor1D 1D Hysteresis
TrigTime1A
TrigTime1B
Inter-RAT CS Measure Stop Ec/No THD
Threshold of stopping inter-RAT measurement for CS services when measurement quantity is
Inter-RAT R99 PS Measure Start Ec/No THD
Threshold of triggering inter-RAT measurement for PS domain non-HSPA services when the
Inter-RAT HSPA Measure Start Ec/No THD
Threshold of triggering inter-RAT measurement for HSPA services when measurement quantity is
Inter-RAT R99 PS Measure Stop Ec/No THD
Threshold of triggering inter-RAT measurement for PS domain non-HSPA services when the
Inter-RAT HSPA Measure Stop Ec/No THD
Threshold of stopping inter-RAT measurement for HSPA services when measurement quantity is
Inter-RAT CS Measure Start RSCP THD
Threshold of triggering inter-RAT measurement for CS services when measurement quantity is
Inter-RAT CS Measure Stop RSCP THD
Threshold of stopping inter-RAT measurement for CS services when measurement quantity is Inter-RAT R99 PS
Measure Start RSCP THD
Threshold of triggering inter-RAT measurement for PS domain non-HSPA services when the
Inter-RAT HSPA Measure Start RSCP THD
Threshold of triggering inter-RAT measurement for HSPA services when measurement quantity is Inter-RAT R99 PS
Measure Stop RSCP THD
Threshold of stopping inter-RAT measurement for PS domain non-HSPA services when the Inter-RAT HSPA
Measure Stop RSCP THD
Threshold of stopping inter-RAT measurement for HSPA services when measurement quantity is
Inter-RAT CS Handover Decision THD
Quality requirement for the cell of another RAT during inter-RAT handover for CS domain
Inter-RAT R99 PS Handover Decision THD
Quality requirement for the cell of another RAT during inter-RAT handover for PS domain
Inter-RAT HSPA Handover Decision THD
Quality requirement for the cell of another RAT during inter-RAT handover for HSPA
VP Service Event 1A Relative Threshold
Relative threshold for event 1A decision when VP service is performed. If this parameter is set to
CS Non-VP Service Event 1A Relative THD
Relative threshold for event 1A decision when non-VP service is performed in CS domain.
PS Service Event 1A Relative Threshold
Relative threshold for event 1A decision when PS service is performed. If this parameter is set to
VP Service Event 1B Relative Threshold
Relative threshold for event 1B decision when VP service is performed. If this parameter is set to CS Non-VP Service
Event 1B Relative Threshold
Relative threshold for event 1B decision when non-VP service is performed in CS domain.
PS Service Event 1B Relative Threshold
Relative threshold for event 1B decision when PS service is performed. If this parameter is set to This parameter specifies the hysteretic value for event 1A. The value of this parameter is This parameter specifies the hysteretic value for event 1B. The value of this parameter is This parameter specifies the hysteretic value for event 1D. The value of this parameter is
Event 1A Triggering Delay
This parameter specifies the interval time between detection of event 1A and sending of the
Event 1B Triggering Delay
This parameter specifies the interval time between detection of event 1B and sending of the
document.xls 文档密级:
04/17/2023 华为机密,未经许可不得扩散 第26页,共66页
TrigTime1D
MaxCellInActiveSet
IdleQhyst1s
ConnQhyst1s
IdleQhyst2s
ConnQhyst2s
Treselections Reselection delay time
Qqualmin Min quality level
Qrxlevmin Min Rx level
IdleSintrasearch
IdleSintersearch
SsearchRat
PICHPowerOffset PICH Power Offset
AICHPowerOffset AICH Power Offset
T3212
ATT
NMO
DRXCycleLenCoef
T302 Timer 302
N302 Constant 302
T309 Timer 309
T312 Timer 312
N312 Constant 312
T313 Timer 313
N313 Constant 313
T314 Timer 314
T315 Timer 315
N315 Constant 315
CIO Cell Individual Offset
Event 1D Triggering Delay
This parameter specifies the interval time between detection of event 1D and sending of the
Max Number of Cell in Active Set
Maximum number of cells in an active set. This parameter is used to achieve the balance
Hysteresis 1 for idle mode
The hysteresis value of the serving FDD cells in idle mode in case the quality measurement for
Hysteresis 1 for connect mode
The hysteresis value of the serving FDD cells in connected mode in case the quality measurement
Hysteresis 2 for idle mode
The hysteresis value of the serving FDD cells in idle mode in case the quality measurement for
Hysteresis 2 for connect mode
The hysteresis value of the serving FDD cells in connected mode in case the quality measurement If the signal quality (CPICH Ec/No measured by the UE) of a neighboring cell is better The minimum required quality threshold corresponding to CPICH Ec/No. The UE can camp The minimum required RX threshold corresponding to CPICH RSCP. The UE can camp Intra-freq cell
reselection threshold for idle mode
Threshold for intra-frequency cell reselection in idle mode. When the quality (CPICH Ec/No Inter-freq cell
reselection threshold for idle mode
Threshold for inter-frequency cell reselection in idle mode. When the quality (CPICH Ec/No
Inter-RAT cell reselection threshold
Threshold for inter-RAT cell reselection. When the quality (CPICH Ec/No measured by UE) of the Difference between the transmit power of PICH and that of PCPICH. For details, refer to the 3GPP This parameter specifies the power offset between the transmit power of an AICH and that of P-
Periodical location update timer
Periodical location update is implemented by MS through the location update
Attach/detach allowed indication
Indicating whether attach/detach is allowed. NOT_ALLOWED indicates that MS cannot
Network mode of operation
This parameter should be set according to the actual network situation . If there is the Gs
DRX cycle length coefficient
CN domain specific Discontinuous Reception (DRX) cycle length coefficient broadcast on T302 is started after the UE transmits the CELL UPDATE/URA UPDATE message and stopped Maximum number of retransmissions of CELL UPDATE/URA UPDATE.Protocol default T309 is started after the UE is reselected to a cell belonging to anotherT312 is started when UE starts to establish a DCH, and stopped when UE detects consecutive Maximum number of successive "in sync" indications received from L1.T313 is started after the UE detects consecutive N313 "out of sync" indications from L1. T313 Maximum number of successive "out of sync" indications received from L1. Protocol default value T314 is started when the criteria for radio link failure are fulfilled and only radio bearers (RBs) T315 is started when the criteria for radio link failure are fulfilled, and only the radio bearer Maximum number of successive "in sync" indications received from L1 when T313 is It is set according to the topographic feature.
document.xls 文档密级:
04/17/2023 华为机密,未经许可不得扩散 第27页,共66页
Qqualmin Min Quality Level
Qrxlevmin Min RX level
CellCapContainerFdd
CellCapContainerFdd
CIO
VPLimitInd VPLimitInd
MaxFachPower
FddTpcDlStepSize
DrxCycleLenCoef
T300 Timer 300
N300 Constant 300
T312 Timer 312
N312 Constant 312
PrdReportInterval
HystFor2D 2D Hysteresis
HystFor2F 2F Hysteresis
TimeToTrig2D Event 2D Trigger Delay
TimeToTrig2F Event 2F Trigger Delay
InterFreqCSThd2DEcN0
InterFreqCSThd2FEcN0
InterFreqR99PsThd2DEcN0
InterFreqHThd2DEcN0
InterFreqR99PsThd2FEcN0
InterFreqHThd2FEcN0
InterFreqCSThd2DRSCP
InterFreqCSThd2FRSCP
InterFreqR99PsThd2DRSCP
InterFreqHThd2DRSCP
This parameter defines the CPICH Ec/No access threshold of the cell. The UE can camp on the cell This parameter defines the CPICH RSCP access threshold of the cell.This parameter is the
Cell Capability Container
1)DELAY_ACTIVATION_SUPPORT (delay activation support indicator):when the
Cell Capability Container
1)DELAY_ACTIVATION_SUPPORT (delay activation support indicator):when the
Cell oriented Cell Individual Offset
The CIO value specified in this parameter cooperates with the neighboring cell oriented Indicates whether the videophone (VP) service is limited in a cell. When the indicator is "TRUE", it
Max Transmit Power of FACH
The offset between the FACH transmit power and P-CPICH transmit power in a cell.
FDD DL power control step size
Step of the closed-loop power control performed on DL DPCH in Frequency Division
Paging DRX cycle coefficient
UTRAN-specific Discontinuous Reception (DRX) cycle length coefficient. In connected T300 is started when UE sends the RRC CONNECTION REQUEST message. It is Maximum number of retransmissions of the RRC CONNECTION REQUEST message.T312 is started when UE starts to establish a DCH, and stopped when UE detects consecutive Maximum number of successive "in sync" indications received from L1.
Inter-frequency Measure Periodical Measurement Report Period
Interval between periodic reporting for the inter-frequency handover. Hysteresis for triggering event 2D.Hysteresis for triggering event 2F.Interval time between detection of event 2D and sending of the measurement report. Interval time between detection of event 2F and sending of the measurement report.This
Inter-freq CS Measure Start Ec/No THD
Ec/No threshold of triggering the inter-frequency measurement for CS services.
Inter-freq CS Measure Stop Ec/No THD
Ec/No threshold of stopping the inter-frequency measurement for CS services.Inter-freq R99 PS
Measure Start Ec/No THD
Ec/No threshold of triggering the inter-frequency measurement for PS non-HSPA
Inter-freq H Measure Start Ec/No THD
Ec/No threshold of triggering the inter-frequency measurement for HSPA services.Inter-freq R99 PS
Measure Stop Ec/No THD
Ec/No threshold of stopping the inter-frequency measurement for PS non-HSPA
Inter-freq H Measure Stop Ec/No THD
Ec/No threshold of stopping the inter-frequency measurement for HSPA services.
Inter-freq CS Measure Start RSCP THD
RSCP threshold of triggering the inter-frequency measurement for CS services.
Inter-freq CS Measure Stop RSCP THD
RSCP threshold of stopping the inter-frequency measurement for CS services.Inter-freq R99 PS
Measure Start RSCP THD
RSCP threshold of triggering the inter-frequency measurement for PS non-HSPA
Inter-freq H Measure Start RSCP THD
RSCP threshold of triggering the inter-frequency measurement for HSPA services.
document.xls 文档密级:
04/17/2023 华为机密,未经许可不得扩散 第28页,共66页
InterFreqR99PsThd2FRSCP
InterFreqHThd2FRSCP
CIOOffset
IdleQoffset1sn IdleQoffset1sn
IdleQoffset2sn IdleQoffset2sn
Qqualmin Min Quality Level
Qrxlevmin Min RX Level
Hystfor2D 2D Hysteresis
Hystfor2F 2F Hysteresis
TrigTime2D
TrigTime2F
InterRATCSThd2DEcN0
InterRATCSThd2FEcN0
InterRATR99PsThd2DEcN0
InterRATHThd2DEcN0
InterRATR99PsThd2FEcN0
InterRATHThd2FEcN0
InterRATCSThd2DRSCP
InterRATCSThd2FRSCP
InterRATR99PsThd2DRSCP
InterRATHThd2DRSCP
InterRATR99PsThd2FRSCP
InterRATHThd2FRSCP
TargetRatCsThd
TargetRatR99PsThd
TargetRatHThd
IntraRelThdFor1ACSVP
IntraRelThdFor1ACSNVP
IntraRelThdFor1APS
Inter-freq R99 PS Measure Stop RSCP THD
RSCP threshold of stopping the inter-frequency measurement for PS non-HSPA
Inter-freq H Measure Stop RSCP THD
RSCP threshold of stopping the inter-frequency measurement for HSPA services.
Neighboring Cell Oriented CIO
Neighboring cell oriented CIO.Cell offset used for CPICH RSCP measurement value in cell selection or Cell offset used for CPICH Ec/No measurement value in cell selection or Minimum CPICH Ec/No for the neighboring cell on cell reselection. The neighboring cell can be Minimum CPICH RSCP for the neighboring cell on cell reselection. The neighboring cell can be
Hysteresis for event 2D. This parameter is used to avoid the ping-pong reporting of event 2D (the estimated quality of the
Hysteresis for event 2F.The value of this parameter is associated with slow fading. If this parameter is set to a
2D Event Trigger Delay Time
Interval time between detection of event 2D and sending of the measurement report.
2F Event Trigger Delay Time
Interval time between detection of event 2F and sending of the measurement report.
Inter-RAT CS Measure Start Ec/No THD
Threshold of triggering inter-RAT measurement for CS services when measurement quantity is
Inter-RAT CS Measure Stop Ec/No THD
Threshold of stopping inter-RAT measurement for CS services when measurement quantity is Inter-RAT R99 PS
Measure Start Ec/No THD
Threshold of triggering inter-RAT measurement for PS domain non-HSPA services when the Inter-RAT HSPA
Measure Start Ec/No THD
Threshold of triggering inter-RAT measurement for HSPA services when measurement quantity is Inter-RAT R99 PS
Measure Stop Ec/No THD
Threshold of triggering inter-RAT measurement for PS domain non-HSPA services when the Inter-RAT HSPA
Measure Stop Ec/No THD
Threshold of stopping inter-RAT measurement for HSPA services when measurement quantity is
Inter-RAT CS Measure Start RSCP THD
Threshold of triggering inter-RAT measurement for CS services when measurement quantity is
Inter-RAT CS Measure Stop RSCP THD
Threshold of stopping inter-RAT measurement for CS services when measurement quantity is Inter-RAT R99 PS
Measure Start RSCP THD
Threshold of triggering inter-RAT measurement for PS domain non-HSPA services when the Inter-RAT HSPA
Measure Start RSCP THD
Threshold of triggering inter-RAT measurement for HSPA services when measurement quantity is Inter-RAT R99 PS
Measure Stop RSCP THD
Threshold of stopping inter-RAT measurement for PS domain non-HSPA services when the Inter-RAT HSPA
Measure Stop RSCP THD
Threshold of stopping inter-RAT measurement for HSPA services when measurement quantity is
Inter-RAT CS Handover Decision THD
Quality requirement for the cell of another RAT during inter-RAT handover for CS domain
Inter-RAT R99 PS Handover Decision THD
Quality requirement for the cell of another RAT during inter-RAT handover for PS domain
Inter-RAT HSPA Handover Decision THD
Quality requirement for the cell of another RAT during inter-RAT handover for HSPA
VP Service Event 1A Relative Threshold
Relative threshold for event 1A decision when VP service is performed. If this parameter is set to
CS Non-VP Service Event 1A Relative THD
Relative threshold for event 1A decision when non-VP service is performed in CS domain.
PS Service Event 1A Relative Threshold
Relative threshold for event 1A decision when PS service is performed. If this parameter is set to
document.xls 文档密级:
04/17/2023 华为机密,未经许可不得扩散 第29页,共66页
IntraRelThdFor1BCSVP
IntraRelThdFor1BCSNVP
IntraRelThdFor1BPS
HystFor1A 1A Hysteresis
HystFor1B 1B Hysteresis
HystFor1D 1D Hysteresis
Weight Weighted factor
TrigTime1A
TrigTime1B
TrigTime1D
CIOOffset
CellsForbidden1A
CellsForbidden1B
IdleQoffset1sn IdleQoffset1sn
IdleQoffset2sn IdleQoffset2sn
PCHPower PCH Power
PCPICHPower
Constantvalue
PreambleRetransMax
PowerRampStep Power Increase Step
PowerOffsetPpm Power Offset
PSCHPower PSCH Transmit Power
NB01min
NB01max
Mmax Max Preamble Loop
SSCHPower SSCH Transmit Power
RlRstrTmr RL restoration timer
CNProtclVer CN protocol version
ConnQoffset1sn ConnQoffset1sn
VP Service Event 1B Relative Threshold
Relative threshold for event 1B decision when VP service is performed. If this parameter is set to CS Non-VP Service
Event 1B Relative Threshold
Relative threshold for event 1B decision when non-VP service is performed in CS domain.
PS Service Event 1B Relative Threshold
Relative threshold for event 1B decision when PS service is performed. If this parameter is set to This parameter specifies the hysteretic value for event 1A. The value of this parameter is This parameter specifies the hysteretic value for event 1B. The value of this parameter is This parameter specifies the hysteretic value for event 1D. The value of this parameter is Used for calculating the relative threshold of the soft handover based on the measurement report
Event 1A Triggering Delay
This parameter specifies the interval time between detection of event 1A and sending of the
Event 1B Triggering Delay
This parameter specifies the interval time between detection of event 1B and sending of the
Event 1D Triggering Delay
This parameter specifies the interval time between detection of event 1D and sending of the
Neighboring Cell Oriented CIO
Neighboring cell oriented CIO.
Affect 1A Threshold Flag
Determines whether event 1A threshold is affected when the cell is added to the active set.
Affect 1B Threshold Flag
Flag of whether adding a cell into the active set will affect the relative threshold of the event Cell offset used for CPICH RSCP measurement value in cell selection or Cell offset used for CPICH Ec/No measurement value in cell selection or Offset of the PCH transmit power from the PCPICH transmit power in a cell. For detailed
PCPICH Transmit Power
TX power of the PCPICH in a cell. This parameter should be set based on the actual system Constant Value for
Calculating Initial TX Power
This parameter specifies a constant used at calculation of the initial transmit power of the first
Max Preamble Retransmission
The maximum number of preambles transmitted in a preamble ramping cycle. For detailed The power ramp step of the random access preambles transmitted before the UE receives The power offset between the last access preamble and the message control part. Offset of the PSCH transmit power from the PCPICH transmit power in a cell.
Random Back-off Lower Limit
Lower limit of random access back-off delay. For details, refer to the 3GPP TS 25.331 and
Random Back-off Upper Limit
Upper limit of random access back-off delay. For details, refer to the 3GPP TS 25.331 and The parameter specifies the maximum number of preambles to be used in one preamble ramping Offset of the SSCH transmit power from the PCPICH transmit power in a cell.A timer to RNC wait for radio link restoration indication in the radio link procedure.Protocol version supported by the CN.Cell offset used for CPICH RSCP measurement value in cell selection or
document.xls 文档密级:
04/17/2023 华为机密,未经许可不得扩散 第30页,共66页
ConnQoffset2sn ConnQoffset2sn
FilterCoef
IntraFreqMeasQuantity
PeriodMRReportNumfor1A
ReportIntervalfor1A
PeriodMRReportNumfor1C
ReportIntervalfor1C
HystFor1C 1C Hysteresis
TrigTime1C
MaxCellInActiveSet
ConnQoffset1sn ConnQoffset1sn
ConnQoffset2sn ConnQoffset2sn
ConnSintrasearch
ConnSintersearch
IntraFreqFilterCoef
IntraFreqMeasQuantity
PeriodMRReportNumfor1A
ReportIntervalfor1A
PeriodMRReportNumfor1C
ReportIntervalfor1C
HystFor1C 1C Hysteresis
Weight Weighted factor
TrigTime1C
ConnCellBarred
ConnIntraFreqReselection
ConnTbarred Time barred for SIB4
CIOOffset
DRA_HSDPA_STATE_TRANS_SWITCH
DRA_HSUPA_STATE_TRANS_SWITCH
Cell offset used for CPICH Ec/No measurement value in cell selection or
Intra-frequency L3 Filter Coefficient
This parameter specifies the Layer 3 filter coefficient for the intra-frequency measurement.
Intra-frequency Measurement Quantity
Quantity of the triggered measurements for intra-frequency handovers. This parameter specifies
Event 1A to Periodical Report Number
Maximum number of reporting event 1A after the reporting mode is changed to periodical
Event 1A to Periodical Report Period
Interval at which event 1A is reported after the reporting mode is changed to periodical
Event 1C to Periodical Report Number
Maximum number of reporting event 1C after the reporting mode is changed to periodical
Event 1C to Periodical Report Period
Interval at which event 1A is reported after the reporting mode is changed to periodical This parameter specifies the hysteretic value for event 1C. The value of this parameter is
Event 1C Triggering Delay
This parameter specifies the interval time between detection of event 1C and sending of the
Max Number of Cell in Active Set
Maximum number of cells in an active set. This parameter is used to achieve the balance Cell offset used for CPICH RSCP measurement value in cell selection or Cell offset used for CPICH Ec/No measurement value in cell selection or Intra-freq cell
reselection threshold for connect mode
Threshold for intra-frequency cell reselection in connected mode. When the quality (CPICH Inter-freq cell
reselection threshold for connect mode
Threshold for inter-frequency cell reselection in connected mode. When the quality (CPICH
Intra-frequency L3 Filter Coefficient
This parameter specifies the Layer 3 filter coefficient for the intra-frequency measurement.
Intra-frequency Measurement Quantity
Quantity of the triggered measurements for intra-frequency handovers. This parameter specifies
Event 1A to Periodical Report Number
Maximum number of reporting event 1A after the reporting mode is changed to periodical
Event 1A to Periodical Report Period
Interval at which event 1A is reported after the reporting mode is changed to periodical
Event 1C to Periodical Report Number
Maximum number of reporting event 1C after the reporting mode is changed to periodical
Event 1C to Periodical Report Period
Interval at which event 1A is reported after the reporting mode is changed to periodical This parameter specifies the hysteretic value for event 1C. The value of this parameter is Used for calculating the relative threshold of the soft handover based on the measurement report
Event 1C Triggering Delay
This parameter specifies the interval time between detection of event 1C and sending of the
Cell barred indicator for SIB4
Indicating whether the UE in connected mode is allowed to access the cell. When the cell status
Intra-freq cell reselection ind for SIB4
Indicating whether the UE in idle mode is allowed to reselect another intra-frequency This parameter is valid when [Cell barred indicator for SIB4] is BARRED. It indicates
Neighboring Cell-Oriented CIO
Cell individual offset for the GSM cell.
Dynamic Resource Allocation Switch
Dynamic resource allocation switch group.
Dynamic Resource Allocation Switch
Dynamic resource allocation switch group.
document.xls 文档密级:
04/17/2023 华为机密,未经许可不得扩散 第31页,共66页
DRA_PS_BE_STATE_TRANS_SWITCH
PsInactTmrForCon
PsInactTmrForStr Streaming service T1
PsInactTmrForInt Interactive service T1
PsInactTmrForBac Background service T1
D2FTvmTimeToTrig BE D2F/R 4B Time
F2PTvmTimeToTrig BE F2P 4B Time
BeF2PStateTransTimer
BeF2DTvmThd BE F/R2D 4A Threshold
BeF2DTvmTimeToTrig BE F/R2D 4A Time
CellReSelectTimer Cell Reselection Timer
BeD2FStateTransTimer
BeH2FStateTransTimer
RlMaxDlPwr RL Max DL TX power
RlMinDlPwr RL Min DL TX power
TargetFreqCsThdEcN0
TargetFreqR99PsThdEcN0
TargetFreqHThdEcN0
TargetFreqCsThdRscp
TargetFreqR99PsThdRscp
TargetFreqHThdRscp
TargetFreqCsThdEcN0
TargetFreqHThdEcN0
TargetFreqR99PsThdEcN0
TargetFreqCsThdRscp
TargetFreqHThdRscp
TargetFreqR99PsThdRscp
Dynamic Resource Allocation Switch
Dynamic resource allocation switch group.
Conversational service T1
When detecting that the Ps' Conversational User had no data to transfer for a long time which When detecting that the Ps' Streaming User had no data to transfer for a long time which longer When detecting that the Ps' Interactive User had no data to transfer for a long time which longer When detecting that the Ps' Background User had no data to transfer for a long time which longer When the traffic volume is below the 4B threshold and remains so for the period specified by this When the traffic volume is below the 4B threshold and remains so for the period specified by this
BE FACH or E_FACH to PCH Transition Timer
Timer for state transition from FACH or E_FACH to PCH of BE services, used to check whether This parameter specifies the threshold of the traffic volume of 4A event for triggering the transition of BE services from FACH This parameter specifies the occurrence time of 4A event for triggering the transition of BE Length of the cell reselection frequency timer. This parameter is used together with
BE DCH to FACH Transition Timer
Timer for state transition from DCH to FACH of BE services, used to check whether the UE in the
BE HS-DSCH to FACH Transition Timer
Timer for state transition from HS-DSCH to FACH of BE services, used to check whether the UE in This parameter specifies the maximum DL RL power to be assigned.This parameter specifies the minimum DL RL power to be assigned.Inter-freq CS Target
Frequency Trigger Ec/No THD
Threshold of the target frequency for triggering inter-frequency measurement based on Inter-freq R99 PS
Target Frequency Trigger Ec/No THD
Threshold of the target frequency for triggering inter-frequency measurement based on Inter-freq HSPA Target
Frequency Trigger Ec/No THD
Threshold of the target frequency for triggering inter-frequency measurement based on Inter-freq CS Target
Frequency Trigger RSCP THD
Threshold of the target frequency for triggering inter-frequency measurement based on Inter-freq R99 PS
Target Frequency Trigger RSCP THD
Threshold of the target frequency for triggering inter-frequency measurement based on Inter-freq HSPA Target
Frequency Trigger RSCP THD
Threshold of the target frequency for triggering inter-frequency measurement based on Inter-freq CS Target
Frequency Trigger Ec/No THD
Threshold of the target frequency for triggering inter-frequency measurement based on Inter-freq HSPA Target
Frequency Trigger Ec/No THD
Threshold of the target frequency for triggering inter-frequency measurement based on Inter-freq R99 PS
Target Frequency Trigger Ec/No THD
Threshold of the target frequency for triggering inter-frequency measurement based on Inter-freq CS Target
Frequency Trigger RSCP THD
Threshold of the target frequency for triggering inter-frequency measurement based on Inter-freq HSPA Target
Frequency Trigger RSCP THD
Threshold of the target frequency for triggering inter-frequency measurement based on Inter-freq R99 PS
Target Frequency Trigger RSCP THD
Threshold of the target frequency for triggering inter-frequency measurement based on
document.xls 文档密级:
04/17/2023 华为机密,未经许可不得扩散 第32页,共66页
Tcell Time Offset
PScrambCode
LAC Location Area Code
SAC Service Area Code
RAC Routing Area Code
CellId Cell ID
UARFCNDownlink Downlink UARFCN
Qhyst1spch
Qhyst1sfach
Qhyst2spch
Qhyst2sfach
Treselectionspch
Treselectionsfach
InterRATPeriodReportInterval
TimeToTrigForVerify
InterRATPingPongTimer
HsScchCodeNum
HoSwitch HandOver Switch
HoSwitch HandOver Switch
HoSwitch HandOver Switch
InterFreqFilterCoef
FilterCoefOf2D2F 2D/2F Filter Coefficient
InterRATFilterCoef
MAXTARGETULLOADFACTOR
MAXHSUPAUSERNUM
10ms Initial SIR Target
2ms Initial SIR Target
10ms Max SIR Target
Difference between the System Frame Number (SFN) and NodeB Frame Number (BFN) of the
DL Primary Scrambling Code
Sequence Number of a DL primary scrambling code in a cell. For detailed information of Identifies a location area code for a Public Land Mobile Network (PLMN) of the GSM-MAP type. It MCC,MNC,LAC and SAC together compose the Service Area ID (SAI). SAI = MCC || MNC || Identifying a routing area in a location area for a Public Land Mobile Network (PLMN)of GSM-ID of a cell. For detailed information about this parameter, see 3GPP TS 25.401.Depending on the value of [Band indication], as shown below:Hysteresis 1 for UE in
CELL_PCH or URA_PCH state
This parameter indicates that in the CELL_PCH or URA_PCH connection mode, the measurement
Hysteresis 1for UE in CELL_FACH state
This parameter indicates that in the CELL_FACH connection mode, the measurement hysteresis Hysteresis 2 for UE in
CELL_PCH or URA_PCH state
This parameter indicates that in the CELL_PCH or URA_PCH connection mode, the measurement
Hysteresis 2 for UE in CELL_FACH state
This parameter indicates that in the CELL_FACH connection mode, the measurement hysteresis
Reselection delay time for UE in PCH state
This parameter indicates the UE reselection delay in the CELL_PCH or URA_PCH connection Reselection delay time
for UE in CELL_FACH state
This parameter indicates the UE reselection delay in the CELL_FACH connection mode. This
Inter-RAT Period Reporting Interval
Interval that the UE reports inter-RAT measurement results to the RNC.Time to Trigger
Handover to Verified GSM Cell
Time delay for triggering handovers to GSM cells with verified BSIC.
Inter-RAT Ping-Pong Timer
Length of the timer to avoid ping-pong handovers between 2G and 3G networks.
Code Number for HS-SCCH
This parameter decides the maximum number of subscribers that the NodeB can schedule in a
HandOver switch group.1) HO_ALGO_HCS_SPEED_EST_SWITCH: When the switch is on, the RNC
HandOver switch group.1) HO_ALGO_HCS_SPEED_EST_SWITCH: When the switch is on, the RNC
HandOver switch group.1) HO_ALGO_HCS_SPEED_EST_SWITCH: When the switch is on, the RNC
Inter-frequency Measure Filter Coeff
This parameter specifies the Layer 3 filter coefficient for the inter-frequency measurementL3 filtering coefficient for event 2D or event 2F measurement
Inter-RAT Filter Coefficient
This parameter specifies the Layer 3 filter coefficient for the inter-RAT measurement.
UL Target Load Factor
The parameter specifies the target value of the uplink load, which is decreased through
HSUPA power control on the NodeB side. For
details about this parameter, refer to 3GPP
TS 25.433
Cell Max HSUPA User Number
defines the admission limit for the number of
EUL users in a cellINITSIRTARGET(10ms)
Defining the initial SIR target value of outer loop power control algorithm
INITSIRTARGET(2ms)
Defining the initial SIR target value of outer loop power control algorithm
MAXSIRTARGET(10ms)
Defining the maximum SIR target value of outer
loop power control algorithm
document.xls 文档密级:
04/17/2023 华为机密,未经许可不得扩散 第33页,共66页
2ms Max SIR Target
MINSIRTARGET Min SIR Target
ERGCH2INDSTPTHS,ERGCH3INDSTPTHS
CQIFBCK(CQIFBCKFORSHO)
MAXSIRTARGET(2ms)
Defining the maximum SIR target value of outer
loop power control algorithm
Defining the minimum SIR target value of outer
loop power control algorithm
reference-E-TFCIreference-E-TFCI-PO
The EDCH Channel PowerOffset
Defining the EDCH Channel PowerOffset
TwoIndexStepThreshold;
ThreeIndexStepThreshold
TwoIndexStepThreshold;
ThreeIndexStepThreshold
EDCHTARGETLITTLERETRANSNUM(10ms) 10ms Target Small Retransmisson
EDCHTARGETLITTLERETRANSNUM(2ms) 2ms Target Small RetransmissonPeriodic of CQI
Feedback
document.xls 文档密级:
04/17/2023 华为机密,未经许可不得扩散 第34页,共66页
MML Command Baseline Value Remarks
ADD U2GNCELL -50~50 0
ADD U2GNCELL -58~-13 -50
ADD UBCH -350~150 -20
ADD UCELLSETUP 0~500 430
ADD UCELLSETUP 1~256 5
ADD UCELLSETUP 1~256 50
ADD UCELLSETUP 0~255 50
ADD UCELLSETUP -20~20 0
ADD UCELLQUICKSETUP -100~500 330
ADD UCELLACCESSSTRICT NOT_RESERVED
ADD UCELLACCESSSTRICT NOT_BARRED
ADD UCELLACCESSSTRICT NOT_BARRED
ADD UCELLACCESSSTRICT NOT_BARRED
ADD UCELLACCESSSTRICT NOT_BARRED
ADD UCELLACCESSSTRICT NOT_BARRED
ADD UCELLACCESSSTRICT NOT_BARRED
ADD UCELLACCESSSTRICT NOT_BARRED
ADD UCELLACCESSSTRICT NOT_BARRED
ADD UCELLACCESSSTRICT NOT_BARRED
ADD UCELLACCESSSTRICT NOT_BARRED
ADD UCELLACCESSSTRICT NOT_BARRED
ADD UCELLACCESSSTRICT NOT_BARRED
ADD UCELLACCESSSTRICT NOT_BARRED
ADD UCELLACCESSSTRICT NOT_BARRED
ADD UCELLACCESSSTRICT NOT_BARRED
ADD UCELLACCESSSTRICT NOT_BARRED
Parameter Value Range
RESERVED, NOT_RESERVEDBARRED, NOT_BARREDBARRED, NOT_BARREDBARRED, NOT_BARREDBARRED, NOT_BARREDBARRED, NOT_BARREDBARRED, NOT_BARREDBARRED, NOT_BARREDBARRED, NOT_BARREDBARRED, NOT_BARREDBARRED, NOT_BARREDBARRED, NOT_BARREDBARRED, NOT_BARREDBARRED, NOT_BARREDBARRED, NOT_BARREDBARRED, NOT_BARREDBARRED, NOT_BARRED
document.xls 文档密级:
04/17/2023 华为机密,未经许可不得扩散 第35页,共66页
ADD UCELLACCESSSTRICT None
ADD UCELLACCESSSTRICT ALLOWED
ADD UCELLACCESSSTRICT D320
ADD UCELLCAC 0~621 61
-500~0 0
D500
0~29 4
0~29 4
D320
D1280
-24~0 -14
-24~0 -12
-24~0 -14
-24~0 -14
-24~0 -12
-24~0 -12
-115~-25 -95
-115~-25 -92
-115~-25 -95
-115~-25 -95
-115~-25 -92
-115~-25 -92
0~29 4
0~29 4
D320
D1280
D0
-24~0 -14
BARRED, NOT_BARREDALLOWED, NOT_ALLOWEDD10, D20, D40, D80, D160, D320, D640, D1280
ADD UCELLHSDPA
Huawei suggests 0, it can improve power usage efficency and HSPA
ADD UCELLINTERFREQHOCOV
NON_PERIODIC_REPORT(Non periodical reporting), D250~1
ADD UCELLINTERFREQHOCOV
ADD UCELLINTERFREQHOCOV
ADD UCELLINTERFREQHOCOV
D0, D10, D20, D40, D60, D80, D100, D120, D160, D200, D240, D320, D640,
ADD UCELLINTERFREQHOCOV
D0, D10, D20, D40, D60, D80, D100, D120, D160, D200, D240, D320, D640,
ADD UCELLINTERFREQHOCOV
ADD UCELLINTERFREQHOCOV
ADD UCELLINTERFREQHOCOV
ADD UCELLINTERFREQHOCOV
ADD UCELLINTERFREQHOCOV
ADD UCELLINTERFREQHOCOV
ADD UCELLINTERFREQHOCOV
ADD UCELLINTERFREQHOCOV
ADD UCELLINTERFREQHOCOV
ADD UCELLINTERFREQHOCOV
ADD UCELLINTERFREQHOCOV
ADD UCELLINTERFREQHOCOV
ADD UCELLINTERRATHOCOV
ADD UCELLINTERRATHOCOV
ADD UCELLINTERRATHOCOV
D0, D10, D20, D40, D60, D80, D100, D120, D160, D200, D240, D320, D640,
ADD UCELLINTERRATHOCOV
D0, D10, D20, D40, D60, D80, D100, D120, D160, D200, D240, D320, D640,
ADD UCELLINTERRATHOCOV
D0, D10, D20, D40, D60, D80, D100, D120, D160, D200, D240, D320, D640,
ADD UCELLINTERRATHOCOV
document.xls 文档密级:
04/17/2023 华为机密,未经许可不得扩散 第36页,共66页
-24~0 -12
-24~0 -15
-24~0 -15
-24~0 -13
-24~0 -13
-115~-25 -100
-115~-25 -97
-115~-25 -110
-115~-25 -110
-115~-25 -107
-115~-25 -107
0~63 16
0~63 16
0~63 16
0~29 6
0~29 6
0~29 6
0~29 12
0~29 12
0~29 12
0~15 0
0~15 0
0~15 8
D320
D640
ADD UCELLINTERRATHOCOV
ADD UCELLINTERRATHOCOV
ADD UCELLINTERRATHOCOV
ADD UCELLINTERRATHOCOV
ADD UCELLINTERRATHOCOV
ADD UCELLINTERRATHOCOV
ADD UCELLINTERRATHOCOV
ADD UCELLINTERRATHOCOV
ADD UCELLINTERRATHOCOV
ADD UCELLINTERRATHOCOV
ADD UCELLINTERRATHOCOV
ADD UCELLINTERRATHOCOV
ADD UCELLINTERRATHOCOV
ADD UCELLINTERRATHOCOV
ADD UCELLINTRAFREQHO
ADD UCELLINTRAFREQHO
ADD UCELLINTRAFREQHO
ADD UCELLINTRAFREQHO
ADD UCELLINTRAFREQHO
ADD UCELLINTRAFREQHO
ADD UCELLINTRAFREQHO
ADD UCELLINTRAFREQHO
ADD UCELLINTRAFREQHO
ADD UCELLINTRAFREQHO
D0, D10, D20, D40, D60, D80, D100, D120, D160, D200, D240, D320, D640,
ADD UCELLINTRAFREQHO
D0, D10, D20, D40, D60, D80, D100, D120, D160, D200, D240, D320, D640,
document.xls 文档密级:
04/17/2023 华为机密,未经许可不得扩散 第37页,共66页
D640
1~6 3
0~20 2
0~20 2
0~20, 255 1
0~20, 255 1
0~31 1
-24~0 -18
-58~-13 -58
-16~10, 127 5
-16~10, 127 4
-16~10, 127 2
ADD UCHPWROFFSET -10~5 -7
ADD UCHPWROFFSET -22~5 -6
0~255 10
ALLOWED
MODE1, MODE2 MODE2
6~9 6
SET UCONNMODETIMER D2000
SET UCONNMODETIMER 0~7 3
SET UCONNMODETIMER 1~8 5
SET UCONNMODETIMER 1~15 6
SET UCONNMODETIMER D1
SET UCONNMODETIMER 0~15 3 OK
SET UCONNMODETIMER D50
SET UCONNMODETIMER D0
SET UCONNMODETIMER D0
SET UCONNMODETIMER D1
-50~50 0
ADD UCELLINTRAFREQHO
D0, D10, D20, D40, D60, D80, D100, D120, D160, D200, D240, D320, D640,
ADD UCELLINTRAFREQHO
ADD UCELLSELRESEL
ADD UCELLSELRESEL
ADD UCELLSELRESEL
ADD UCELLSELRESEL
ADD UCELLSELRESEL
ADD UCELLSELRESEL
ADD UCELLSELRESEL
ADD UCELLSELRESEL
ADD UCELLSELRESEL
ADD UCELLSELRESEL
ADD UCNDOMAIN
ADD UCNDOMAIN NOT_ALLOWED, ALLOWED
ADD UCNDOMAIN
ADD UCNDOMAIN
Huawei suggests 6, because paging delay is big when this parameter is
D100, D200, D400, D600, D800, D1000, D1200, D1400, D1600,
D1, D2, D4, D10, D20, D50, D100, D200, D400, D600, D800, D1000
D1, D2, D4, D10, D20, D50, D100, D200
NOK:50, Avoid call drop,
D0, D2, D4, D6, D8, D12, D16, D20D0, D10, D30, D60, D180, D600, D1200, D1800D1, D2, D4, D10, D20, D50, D100, D200, D400, D600, D800, D1000
ADD UEXT2GCELL
document.xls 文档密级:
04/17/2023 华为机密,未经许可不得扩散 第38页,共66页
-24~0 -18
-58~-13
None
None
-20~20 0
ADD UCELLSETUP TRUE, FALSE 0
ADD UFACH -350~150 10
SET UFRC STEPSIZE_1DB
SET UFRC 3~9 6
SET UIDLEMODETIMER D2000
SET UIDLEMODETIMER 0~7 3
SET UIDLEMODETIMER 1~15 6
SET UIDLEMODETIMER D1
SET UINTERFREQHOCOV D500
SET UINTERFREQHOCOV 0~29 4
SET UINTERFREQHOCOV 0~29 4
SET UINTERFREQHOCOV D320
SET UINTERFREQHOCOV D1280
SET UINTERFREQHOCOV -24~0 -14
SET UINTERFREQHOCOV -24~0 -12
SET UINTERFREQHOCOV -24~0 -14
SET UINTERFREQHOCOV -24~0 -14
SET UINTERFREQHOCOV -24~0 -12
SET UINTERFREQHOCOV -24~0 -12
SET UINTERFREQHOCOV -115~-25 -95
SET UINTERFREQHOCOV -115~-25 -92
SET UINTERFREQHOCOV -115~-25 -95
SET UINTERFREQHOCOV -115~-25 -95
ADD UEXT3GCELL
ADD UEXT3GCELL无
ADD UEXT3GCELL
DELAY_ACTIVATION_SUPPORT(delay activation support indication),
ADD UEXT3GCELL
DELAY_ACTIVATION_SUPPORT(delay activation support indication),
ADD UEXT3GCELL
STEPSIZE_0.5DB, STEPSIZE_1DB, STEPSIZE_1.5DB, STEPSIZE_2DB
We suggest 1dB.HW Power control performance for 1dB step is Huawei suggests 6, because paging delay is big when this parameter is
D100, D200, D400, D600, D800, D1000, D1200, D1400, D1600,
D1, D2, D4, D10, D20, D50, D100, D200, D400, D600, D800, D1000NON_PERIODIC_REPORT(Non periodical reporting), D250~1
D0, D10, D20, D40, D60, D80, D100, D120, D160, D200, D240, D320, D640, D0, D10, D20, D40, D60, D80, D100, D120, D160, D200, D240, D320, D640,
document.xls 文档密级:
04/17/2023 华为机密,未经许可不得扩散 第39页,共66页
SET UINTERFREQHOCOV -115~-25 -92
SET UINTERFREQHOCOV -115~-25 -92
-20~20 0
-50~50 0
-50~50 0
-24~0 -18
-58~-13
SET UINTERRATHOCOV 0~29 4
SET UINTERRATHOCOV 0~29 4
SET UINTERRATHOCOV D320
SET UINTERRATHOCOV D1280
SET UINTERRATHOCOV -24~0 -14
SET UINTERRATHOCOV -24~0 -12
SET UINTERRATHOCOV -24~0 -15
SET UINTERRATHOCOV -24~0 -15
SET UINTERRATHOCOV -24~0 -13
SET UINTERRATHOCOV -24~0 -13
SET UINTERRATHOCOV -115~-25 -100
SET UINTERRATHOCOV -115~-25 -97
SET UINTERRATHOCOV -115~-25 -110
SET UINTERRATHOCOV -115~-25 -110
SET UINTERRATHOCOV -115~-25 -107
SET UINTERRATHOCOV -115~-25 -107
SET UINTERRATHOCOV 0~63 16
SET UINTERRATHOCOV 0~63 16
SET UINTERRATHOCOV 0~63 16
SET UINTRAFREQHO 0~29 6
SET UINTRAFREQHO 0~29 6
SET UINTRAFREQHO 0~29 6
ADD UINTERFREQNCELL
ADD UINTERFREQNCELL
ADD UINTERFREQNCELL
ADD UINTERFREQNCELL
ADD UINTERFREQNCELL无
D0, D10, D20, D40, D60, D80, D100, D120, D160, D200, D240, D320, D640, D0, D10, D20, D40, D60, D80, D100, D120, D160, D200, D240, D320, D640,
6=3dB,use huawei default6=3dB,use huawei default
document.xls 文档密级:
04/17/2023 华为机密,未经许可不得扩散 第40页,共66页
SET UINTRAFREQHO 0~29 12
SET UINTRAFREQHO 0~29 12
SET UINTRAFREQHO 0~29 12
SET UINTRAFREQHO 0~15 0
SET UINTRAFREQHO 0~15 0
SET UINTRAFREQHO 0~15 8
SET UINTRAFREQHO 0~20 0
SET UINTRAFREQHO D320
SET UINTRAFREQHO D640
SET UINTRAFREQHO D640
-20~20 0
AFFECT
AFFECT
-50~50 0
-50~50 0
ADD UPCH -350~150 -20
ADD UPCPICH -100~500 330
ADD UPRACHBASIC -35~-10 -20
ADD UPRACHBASIC 1~64 20
ADD UPRACHBASIC 1~8 2
ADD UPRACHTFC -5~10
ADD UPSCH -350~150 -50
0~50 0
0~50 0
1~32 8
ADD USSCH -350~150 -50
SET USTATETIMER 1~300000 11000
None
-50~50 0
D0, D10, D20, D40, D60, D80, D100, D120, D160, D200, D240, D320, D640, D0, D10, D20, D40, D60, D80, D100, D120, D160, D200, D240, D320, D640,
HW suggests D1280 to avoid PingPang handover.
D0, D10, D20, D40, D60, D80, D100, D120, D160, D200, D240, D320, D640,
ADD UINTRAFREQNCELL
ADD UINTRAFREQNCELL AFFECT, NOT_AFFECT
ADD UINTRAFREQNCELL AFFECT, NOT_AFFECT
ADD UINTRAFREQNCELL
ADD UINTRAFREQNCELL
In signaling transmission mode, set PowerOffsetPpm to
ADD URACH
ADD URACH
ADD URACH
ADD UCNNODE(Mandatory) R99, R4, R5, R6, R7, R8
ADD UINTERFREQNCELL
document.xls 文档密级:
04/17/2023 华为机密,未经许可不得扩散 第41页,共66页
-50~50 0
SET UINTRAFREQHO D3
SET UINTRAFREQHO CPICH_EC/NO
SET UINTRAFREQHO D16
SET UINTRAFREQHO D4000 4s is enough
SET UINTRAFREQHO D16
SET UINTRAFREQHO D4000 4s is enough
SET UINTRAFREQHO 0~15 8
SET UINTRAFREQHO D640
SET UINTRAFREQHO 1~6 3
-50~50 0
-50~50 0
-16~10, 127 5
-16~10, 127 4
D3
CPICH_EC/NO
D16
D4000
D16
D4000
0~15 8
0~20 0
D640
ADD UCELLACCESSSTRICT None
ADD UCELLACCESSSTRICT NOT_ALLOWED
ADD UCELLACCESSSTRICT D1280
ADD U2GNCELL -50~50 0
SET UCORRMALGOSWITCH
SET UCORRMALGOSWITCH
ADD UINTERFREQNCELL D0, D1, D2, D3, D4, D5, D6, D7, D8, D9, D11, D13, D15, D17, D19CPICH_EC/NO, CPICH_RSCPD1~0 D2~1 D4~2 D8~3 D16~4 D32~5 D64~6 INFINITYNON_PERIODIC_REPORT, D250~1 D500~2 D1000~3 D2000~4 D4000~5 D1~0 D2~1 D4~2 D8~3 D16~4 D32~5 D64~6 INFINITYNON_PERIODIC_REPORT, D250~1 D500~2 D1000~3 D2000~4 D4000~5 D0, D10, D20, D40, D60, D80, D100, D120, D160, D200, D240, D320, D640,
ADD UINTRAFREQNCELL
ADD UINTRAFREQNCELL
ADD UCELLSELRESEL
ADD UCELLSELRESEL
ADD UCELLINTRAFREQHO
D0, D1, D2, D3, D4, D5, D6, D7, D8, D9, D11, D13, D15, D17, D19
ADD UCELLINTRAFREQHO CPICH_EC/NO, CPICH_RSCP
ADD UCELLINTRAFREQHOD1~0 D2~1 D4~2 D8~3 D16~4 D32~5 D64~6 INFINITY
ADD UCELLINTRAFREQHO
NON_PERIODIC_REPORT, D250~1 D500~2 D1000~3 D2000~4 D4000~5
ADD UCELLINTRAFREQHOD1~0 D2~1 D4~2 D8~3 D16~4 D32~5 D64~6 INFINITY
ADD UCELLINTRAFREQHO
NON_PERIODIC_REPORT, D250~1 D500~2 D1000~3 D2000~4 D4000~5
ADD UCELLINTRAFREQHO
ADD UCELLINTRAFREQHO
ADD UCELLINTRAFREQHO
D0, D10, D20, D40, D60, D80, D100, D120, D160, D200, D240, D320, D640, BARRED, NOT_BARREDALLOWED, NOT_ALLOWEDD10(10 seconds), D20(20 seconds), D40(40 seconds), D80(80 seconds), DRA_AQM_SWITCH, DRA_BASE_ADM_CE_BE_TTI_L2_O
DRA_AQM_SWITCH:OFF, DRA_BASE_ADM_CE_BE_TTI_L2_O
HW suggests DRA_HSDPA_DL_FLOW_CONTROL_SWITCH:OFF
DRA_AQM_SWITCH, DRA_BASE_ADM_CE_BE_TTI_L2_O
DRA_AQM_SWITCH:OFF, DRA_BASE_ADM_CE_BE_TTI_L2_O
HW suggests DRA_HSDPA_DL_FLOW_CONTROL_SWITCH:OFF
document.xls 文档密级:
04/17/2023 华为机密,未经许可不得扩散 第42页,共66页
SET UCORRMALGOSWITCH
SET UPSINACTTIMER 0~14400 20
SET UPSINACTTIMER 0~14400 20
SET UPSINACTTIMER 0~14400 20
SET UPSINACTTIMER 0~14400 20
SET UUESTATETRANS D5000
SET UUESTATETRANS D5000
SET UUESTATETRANSTIMER 1~65535 65535
SET UUESTATETRANS D1024
SET UUESTATETRANS D0
SET UUESTATETRANSTIMER 1~65535 180
SET UUESTATETRANSTIMER 1~65535 5
SET UUESTATETRANSTIMER 1~65535 5 OK,5->20
-350~150 None
-350~150 None
SET UINTERFREQHOCOV -24~0 -12
SET UINTERFREQHOCOV -24~0 -12
SET UINTERFREQHOCOV -24~0 -12
SET UINTERFREQHOCOV -115~-25 -92
SET UINTERFREQHOCOV -115~-25 -92
SET UINTERFREQHOCOV -115~-25 -92
-24~0 -12
-24~0 -12
-24~0 -12
-115~-25 -92
-115~-25 -92
ADD UCELLINTERFREQHOCOV -115~-25 -92
DRA_AQM_SWITCH, DRA_BASE_ADM_CE_BE_TTI_L2_O
DRA_AQM_SWITCH:OFF, DRA_BASE_ADM_CE_BE_TTI_L2_O
HW suggests DRA_HSDPA_DL_FLOW_CONTROL_SWITCH:OFF
D0, D10, D20, D40, D60, D80, D100, D120, D160, D200, D240, D320, D640,
HW suggests a bigger trigger timer to prevent PingPang D2F
D0, D10, D20, D40, D60, D80, D100, D120, D160, D200, D240, D320, D640,
HW suggests a bigger value to prevent PingPong F2P.because there are big delay for data transmission if UE is in PCH status, so
D16, D32, D64, D128, D256, D512, D1024, D2k, D3k, D4k, D6k, D8k, D12k, D16k, D24k, D0, D10, D20, D40, D60, D80, D100, D120, D160, D200, D240, D320, D640,
HW suggests D0 because it can speed up data transmission and
ADD UCELLRLPWR
ADD UCELLRLPWR
Threshold for InterFrequency HO should be discussed in Threshold for InterFrequency HO should be discussed in Threshold for InterFrequency HO should be discussed in Threshold for InterFrequency HO should be discussed in Threshold for InterFrequency HO should be discussed in
ADD UCELLINTERFREQHOCOV
ADD UCELLINTERFREQHOCOV
Threshold for InterFrequency HO should be discussed in
ADD UCELLINTERFREQHOCOV
Threshold for InterFrequency HO should be discussed in
ADD UCELLINTERFREQHOCOV
Threshold for InterFrequency HO should be discussed in
ADD UCELLINTERFREQHOCOV
Threshold for InterFrequency HO should be discussed in Threshold for InterFrequency HO should be discussed in
document.xls 文档密级:
04/17/2023 华为机密,未经许可不得扩散 第43页,共66页
ADD UCELLSETUP None
ADD UCELLSETUP 0~511 None
ADD UCELLSETUP 1~65533, 65535 None
ADD UCELLSETUP 0~65535 None
ADD UCELLSETUP 0~255 None
ADD UCELLSETUP 0~65535 None
ADD UCELLSETUP 0~16383 None
0~40, 255 255
0~40, 255 255
0~40, 255 255
0~40, 255 255
0~31, 255 255
0~31, 255 255
D1000
ADD UCELLINTERRATHOCOV 0~64000 0
0~65535 0
ADD UCELLHSDPA 1~15 4
SET UCORRMALGOSWITCH
SET UCORRMALGOSWITCH
SET UCORRMALGOSWITCH
D3
D3
ADD UCELLHSUPA 75 75
ADD UCELLCAC 20 20
ADD UTYPRABHSUPAPC 0-255 162
ADD UTYPRABHSUPAPC 0-255 162
ADD UTYPRABHSUPAPC 0-255 192
CHIP0, CHIP256, CHIP512, CHIP768, CHIP1024, CHIP1280,
ADD UCELLSELRESEL
ADD UCELLSELRESEL
ADD UCELLSELRESEL
ADD UCELLSELRESEL
ADD UCELLSELRESEL
ADD UCELLSELRESEL
ADD UCELLINTERRATHOCOV
NON_PERIODIC_REPORT(Non periodical reporting), D250~1
ADD UCELLINTERRATHOCOV
HO_ALGO_HCS_SPEED_EST_SWITCH, HO_ALGO_LDR_A
HO_ALGO_HCS_SPEED_EST_SWITCH:OFF, HO_ALGO_LDR_A
We suggest HO_MC_SIGNAL_SWITCH:OFF, HO_ALGO_OVERL
HO_ALGO_HCS_SPEED_EST_SWITCH, HO_ALGO_LDR_A
HO_ALGO_HCS_SPEED_EST_SWITCH:OFF, HO_ALGO_LDR_A
We suggest HO_MC_SIGNAL_SWITCH:OFF, HO_ALGO_OVERLHO_ALGO_HCS_S
PEED_EST_SWITCH, HO_ALGO_LDR_A
HO_ALGO_HCS_SPEED_EST_SWITCH:OFF, HO_ALGO_LDR_A
We suggest HO_MC_SIGNAL_SWITCH:OFF, HO_ALGO_OVERLADD
UCELLINTERFREQHONCOV
D0, D1, D2, D3, D4, D5, D6, D7, D8, D9, D11, D13, D15, D17, D19
For low speed(5km/h):Range is D4~D6, the recommended
ADD UCELLINTERRATHOCOV
D0, D1, D2, D3, D4, D5, D6, D7, D8, D9, D11, D13, D15, D17, D19
ADD UCELLINTERRATHOCOV
D0, D1, D2, D3, D4, D5, D6, D7, D8, D9, D11, D13, D15, D17, D19
0~100
0~100
8dB:(X-82)/10
8dB:(X-82)/10
11dB:(X-82)/10
document.xls 文档密级:
04/17/2023 华为机密,未经许可不得扩散 第44页,共66页
ADD UTYPRABHSUPAPC 0-255 222
ADD UTYPRABHSUPAPC 0-255 62
ADD UTYPRABHSUPAPC
ADD UTYPRABHSUPAPC
ADD UTYPRABOLPC 1-100 1% 1%
ADD UTYPRABOLPC 10% 10%
ADD UHSDPCCH 2 2ms
14dB:(X-82)/10
-2dB:(X-82)/10REFETFCIIDX1=4,
REFETFCIIDX2=54,
REFETFCIPO1=PO_15/15,
REFETFCIPO2=PO_67/15
ERGCH2INDSTPTHS=12,
ERGCH3INDSTPTHS=9
document.xls 文档密级:
04/17/2023 华为机密,未经许可不得扩散 第45页,共66页
NSN
RU20
Parameter ID Meaning
AdjgQoffset1 0 dB
AdjgQrxlevMin -115 dBm
PtxPrimaryCCPCH -5dbm
PtxCellMax 43 dBm
PtxPrimaryCPICH 33 dBm
Cell_Reserved Not reserved
ACBarredList 0
ACBarredList 0
ACBarredList 0
ACBarredList 0
ACBarredList 0
ACBarredList 0
ACBarredList 0
ACBarredList 0
ACBarredList 0
ACBarredList 0
ACBarredList 0
ACBarredList 0
ACBarredList 0
ACBarredList 0
ACBarredList 0
ACBarredList 0
Parameter Value Range
Recommended Value
This parameter is used in the cell re-selection and ranking between WCDMA and GSM cells. The value of this parameter is subtracted from the measured GSM carrier RSSI of the neighbouring cell before the UE compares the quality measure with the cell re-selection//ranking criteria./nThis parameter is part of System Information Block 11&12.
-50...50 dB, step 1 dB
Determines the minimum required RSSI level which the measurement result of the GSM neighbour cell must exceed before the cell re-selection becomes possible./nThis parameter is part of System Information Block 11&12.
-115...-25 dBm, step 2 dBm
This is the transmission power of the primary CCPCH relative to the CPICH transmission power. The P-CCPCH is a fixed rate (15 ksps, SF = 256) downlink physical channel used to carry the BCH. It is a pure data channel and characterized by a fixed channelisation code (Cch,256,1). The P-CCPCH is broadcast over the entire cell and it is not transmitted during the first 256 chips of each slot, where Primary SCH and Secondary SCH are transmitted. Note: Changing the parameter value will start the cell shutdown procedure in the BTS.
-35...15 dB, step 0.1 dB
This parameter defines the maximum transmission power of the cell. The maximum transmission power is the maximum value for the linear sum of the power of all downlink physical channels that is allowed to be used in a cell. The maximum transmission power of the cell is the minimum of the two parameters: PtxCellMax and MaxDLPowerCapability (the maximum BTS power capability). The RNC signals the BTS the minimum value as the maximum transmission power in Maximum Transmission Power IE (TS 25.433). The RNC uses the minimum value as the maximum transmission power of the cell. If HSDPA static resource allocation is active, the value of the PtxMaxHSDPA parameter added with the value of the PtxTargetHSDPA parameter must not exceed the cell maximum transmission power defined by the minimum of the following parameters: PtxCellMax and MaxDLPowerCapability. Otherwise Rthe NC internally limits the HSDPA power.
0...50 dBm, step 0.1 dBm
This is the transmission power of the primary common pilot channel. The P-CPICH physical channel carries the common pilots of the cell, which is defined in the cell setup. The transmission power of the CPICH physical channel defines the actual cell size, which means that the power is determined by radio network planning. This parameter is used, for example, for neighbour measurements - critical for the network performance. The default value is 5-10% of the maximum transmitting power of WCDMA BTS, which can be, for example, 43 dBm/carrier. Note: Changing the parameter value will start the cell shutdown procedure in the BTS. Note: The cell is blocked if the WCDMA BTS does not support the used value. Typical supported range is (Cell max power - 18dB)..(Cell max power - 3dB). This parameter is part of System Information Block 5.
-10...50 dBm, step 0.1 dBm
Defines whether the cell is reserved for operator use or not. A reserved cell is a cell on which camping is not allowed, except for particular UEs, if so indicated./nWhen cell status is 'not barred' and 'not reserved' for operator use the UE may select//re-select this cell during the cell selection and cell re-selection procedures in Idle mode and in Connected mode./nWhen cell status is 'not barred' and 'reserved' for operator use, the UEs assigned to Access Class 11 or 15 may select//re-select this cell if in the home PLMN. UEs assigned to Access Class in the range 0 to 9 and 12 to 14 shall behave as if cell status 'barred' is indicated./nThis parameter is part of System Information Block 3.
Reserved (0), Not reserved (1)
Access Class Barred list' information defines whether access is barred for each of the 16 Access Classes (AC0...AC15). 'Access Class Barred list' uses a binary notation of 16 bits where - bit 0 indicates whether access is barred for AC0 - bit 1 indicates whether access is barred for AC1 - bit 2 indicates whether access is barred for AC2 ... - bit 15 indicates whether access is barred for AC15 If a bit is set to 1, the corresponding Access Class is 'barred'. If a bit is set to 0, the corresponding Access Class is 'not barred'. If Access Class 10 is indicated as barred in a cell, UEs with Access Class 0 to 9 or without an IMSI are not allowed to initiate emergency calls in this cell. For UEs with Access Classes 11 to 15, emergency calls are not allowed if both Access Class 10 and the relevant Access Class (11 to 15) are barred. Otherwise, emergency calls are allowed for those UEs. Note: This value is used in SIB3 only when AccessClassRegulation is disabled in a cell. If AccessClassRegulation is enabled, only Access Classes 10 to 15 can be barred with this parameter.
Bit 0: Access Class 0, Bit 1: Access Class 1, Bit 2: Access Class 2, Bit 3: Access Class 3, Bit 4: Access Class 4, Bit 5: Access Class 5, Bit 6: Access Class 6, Bit 7: Access Class 7, Bit 8: Access Class 8, Bit 9: Access Class 9, Bit 10: Access Class 10, Bit 11: Access Class 11, Bit 12: Access Class 12, Bit 13: Access Class 13, Bit 14: Access Class 14, Bit 15: Access Class 15
Access Class Barred list' information defines whether access is barred for each of the 16 Access Classes (AC0...AC15). 'Access Class Barred list' uses a binary notation of 16 bits where - bit 0 indicates whether access is barred for AC0 - bit 1 indicates whether access is barred for AC1 - bit 2 indicates whether access is barred for AC2 ... - bit 15 indicates whether access is barred for AC15 If a bit is set to 1, the corresponding Access Class is 'barred'. If a bit is set to 0, the corresponding Access Class is 'not barred'. If Access Class 10 is indicated as barred in a cell, UEs with Access Class 0 to 9 or without an IMSI are not allowed to initiate emergency calls in this cell. For UEs with Access Classes 11 to 15, emergency calls are not allowed if both Access Class 10 and the relevant Access Class (11 to 15) are barred. Otherwise, emergency calls are allowed for those UEs. Note: This value is used in SIB3 only when AccessClassRegulation is disabled in a cell. If AccessClassRegulation is enabled, only Access Classes 10 to 15 can be barred with this parameter.
Bit 0: Access Class 0, Bit 1: Access Class 1, Bit 2: Access Class 2, Bit 3: Access Class 3, Bit 4: Access Class 4, Bit 5: Access Class 5, Bit 6: Access Class 6, Bit 7: Access Class 7, Bit 8: Access Class 8, Bit 9: Access Class 9, Bit 10: Access Class 10, Bit 11: Access Class 11, Bit 12: Access Class 12, Bit 13: Access Class 13, Bit 14: Access Class 14, Bit 15: Access Class 15
Access Class Barred list' information defines whether access is barred for each of the 16 Access Classes (AC0...AC15). 'Access Class Barred list' uses a binary notation of 16 bits where - bit 0 indicates whether access is barred for AC0 - bit 1 indicates whether access is barred for AC1 - bit 2 indicates whether access is barred for AC2 ... - bit 15 indicates whether access is barred for AC15 If a bit is set to 1, the corresponding Access Class is 'barred'. If a bit is set to 0, the corresponding Access Class is 'not barred'. If Access Class 10 is indicated as barred in a cell, UEs with Access Class 0 to 9 or without an IMSI are not allowed to initiate emergency calls in this cell. For UEs with Access Classes 11 to 15, emergency calls are not allowed if both Access Class 10 and the relevant Access Class (11 to 15) are barred. Otherwise, emergency calls are allowed for those UEs. Note: This value is used in SIB3 only when AccessClassRegulation is disabled in a cell. If AccessClassRegulation is enabled, only Access Classes 10 to 15 can be barred with this parameter.
Bit 0: Access Class 0, Bit 1: Access Class 1, Bit 2: Access Class 2, Bit 3: Access Class 3, Bit 4: Access Class 4, Bit 5: Access Class 5, Bit 6: Access Class 6, Bit 7: Access Class 7, Bit 8: Access Class 8, Bit 9: Access Class 9, Bit 10: Access Class 10, Bit 11: Access Class 11, Bit 12: Access Class 12, Bit 13: Access Class 13, Bit 14: Access Class 14, Bit 15: Access Class 15
Access Class Barred list' information defines whether access is barred for each of the 16 Access Classes (AC0...AC15). 'Access Class Barred list' uses a binary notation of 16 bits where - bit 0 indicates whether access is barred for AC0 - bit 1 indicates whether access is barred for AC1 - bit 2 indicates whether access is barred for AC2 ... - bit 15 indicates whether access is barred for AC15 If a bit is set to 1, the corresponding Access Class is 'barred'. If a bit is set to 0, the corresponding Access Class is 'not barred'. If Access Class 10 is indicated as barred in a cell, UEs with Access Class 0 to 9 or without an IMSI are not allowed to initiate emergency calls in this cell. For UEs with Access Classes 11 to 15, emergency calls are not allowed if both Access Class 10 and the relevant Access Class (11 to 15) are barred. Otherwise, emergency calls are allowed for those UEs. Note: This value is used in SIB3 only when AccessClassRegulation is disabled in a cell. If AccessClassRegulation is enabled, only Access Classes 10 to 15 can be barred with this parameter.
Bit 0: Access Class 0, Bit 1: Access Class 1, Bit 2: Access Class 2, Bit 3: Access Class 3, Bit 4: Access Class 4, Bit 5: Access Class 5, Bit 6: Access Class 6, Bit 7: Access Class 7, Bit 8: Access Class 8, Bit 9: Access Class 9, Bit 10: Access Class 10, Bit 11: Access Class 11, Bit 12: Access Class 12, Bit 13: Access Class 13, Bit 14: Access Class 14, Bit 15: Access Class 15
Access Class Barred list' information defines whether access is barred for each of the 16 Access Classes (AC0...AC15). 'Access Class Barred list' uses a binary notation of 16 bits where - bit 0 indicates whether access is barred for AC0 - bit 1 indicates whether access is barred for AC1 - bit 2 indicates whether access is barred for AC2 ... - bit 15 indicates whether access is barred for AC15 If a bit is set to 1, the corresponding Access Class is 'barred'. If a bit is set to 0, the corresponding Access Class is 'not barred'. If Access Class 10 is indicated as barred in a cell, UEs with Access Class 0 to 9 or without an IMSI are not allowed to initiate emergency calls in this cell. For UEs with Access Classes 11 to 15, emergency calls are not allowed if both Access Class 10 and the relevant Access Class (11 to 15) are barred. Otherwise, emergency calls are allowed for those UEs. Note: This value is used in SIB3 only when AccessClassRegulation is disabled in a cell. If AccessClassRegulation is enabled, only Access Classes 10 to 15 can be barred with this parameter.
Bit 0: Access Class 0, Bit 1: Access Class 1, Bit 2: Access Class 2, Bit 3: Access Class 3, Bit 4: Access Class 4, Bit 5: Access Class 5, Bit 6: Access Class 6, Bit 7: Access Class 7, Bit 8: Access Class 8, Bit 9: Access Class 9, Bit 10: Access Class 10, Bit 11: Access Class 11, Bit 12: Access Class 12, Bit 13: Access Class 13, Bit 14: Access Class 14, Bit 15: Access Class 15
Access Class Barred list' information defines whether access is barred for each of the 16 Access Classes (AC0...AC15). 'Access Class Barred list' uses a binary notation of 16 bits where - bit 0 indicates whether access is barred for AC0 - bit 1 indicates whether access is barred for AC1 - bit 2 indicates whether access is barred for AC2 ... - bit 15 indicates whether access is barred for AC15 If a bit is set to 1, the corresponding Access Class is 'barred'. If a bit is set to 0, the corresponding Access Class is 'not barred'. If Access Class 10 is indicated as barred in a cell, UEs with Access Class 0 to 9 or without an IMSI are not allowed to initiate emergency calls in this cell. For UEs with Access Classes 11 to 15, emergency calls are not allowed if both Access Class 10 and the relevant Access Class (11 to 15) are barred. Otherwise, emergency calls are allowed for those UEs. Note: This value is used in SIB3 only when AccessClassRegulation is disabled in a cell. If AccessClassRegulation is enabled, only Access Classes 10 to 15 can be barred with this parameter.
Bit 0: Access Class 0, Bit 1: Access Class 1, Bit 2: Access Class 2, Bit 3: Access Class 3, Bit 4: Access Class 4, Bit 5: Access Class 5, Bit 6: Access Class 6, Bit 7: Access Class 7, Bit 8: Access Class 8, Bit 9: Access Class 9, Bit 10: Access Class 10, Bit 11: Access Class 11, Bit 12: Access Class 12, Bit 13: Access Class 13, Bit 14: Access Class 14, Bit 15: Access Class 15
Access Class Barred list' information defines whether access is barred for each of the 16 Access Classes (AC0...AC15). 'Access Class Barred list' uses a binary notation of 16 bits where - bit 0 indicates whether access is barred for AC0 - bit 1 indicates whether access is barred for AC1 - bit 2 indicates whether access is barred for AC2 ... - bit 15 indicates whether access is barred for AC15 If a bit is set to 1, the corresponding Access Class is 'barred'. If a bit is set to 0, the corresponding Access Class is 'not barred'. If Access Class 10 is indicated as barred in a cell, UEs with Access Class 0 to 9 or without an IMSI are not allowed to initiate emergency calls in this cell. For UEs with Access Classes 11 to 15, emergency calls are not allowed if both Access Class 10 and the relevant Access Class (11 to 15) are barred. Otherwise, emergency calls are allowed for those UEs. Note: This value is used in SIB3 only when AccessClassRegulation is disabled in a cell. If AccessClassRegulation is enabled, only Access Classes 10 to 15 can be barred with this parameter.
Bit 0: Access Class 0, Bit 1: Access Class 1, Bit 2: Access Class 2, Bit 3: Access Class 3, Bit 4: Access Class 4, Bit 5: Access Class 5, Bit 6: Access Class 6, Bit 7: Access Class 7, Bit 8: Access Class 8, Bit 9: Access Class 9, Bit 10: Access Class 10, Bit 11: Access Class 11, Bit 12: Access Class 12, Bit 13: Access Class 13, Bit 14: Access Class 14, Bit 15: Access Class 15
Access Class Barred list' information defines whether access is barred for each of the 16 Access Classes (AC0...AC15). 'Access Class Barred list' uses a binary notation of 16 bits where - bit 0 indicates whether access is barred for AC0 - bit 1 indicates whether access is barred for AC1 - bit 2 indicates whether access is barred for AC2 ... - bit 15 indicates whether access is barred for AC15 If a bit is set to 1, the corresponding Access Class is 'barred'. If a bit is set to 0, the corresponding Access Class is 'not barred'. If Access Class 10 is indicated as barred in a cell, UEs with Access Class 0 to 9 or without an IMSI are not allowed to initiate emergency calls in this cell. For UEs with Access Classes 11 to 15, emergency calls are not allowed if both Access Class 10 and the relevant Access Class (11 to 15) are barred. Otherwise, emergency calls are allowed for those UEs. Note: This value is used in SIB3 only when AccessClassRegulation is disabled in a cell. If AccessClassRegulation is enabled, only Access Classes 10 to 15 can be barred with this parameter.
Bit 0: Access Class 0, Bit 1: Access Class 1, Bit 2: Access Class 2, Bit 3: Access Class 3, Bit 4: Access Class 4, Bit 5: Access Class 5, Bit 6: Access Class 6, Bit 7: Access Class 7, Bit 8: Access Class 8, Bit 9: Access Class 9, Bit 10: Access Class 10, Bit 11: Access Class 11, Bit 12: Access Class 12, Bit 13: Access Class 13, Bit 14: Access Class 14, Bit 15: Access Class 15
Access Class Barred list' information defines whether access is barred for each of the 16 Access Classes (AC0...AC15). 'Access Class Barred list' uses a binary notation of 16 bits where - bit 0 indicates whether access is barred for AC0 - bit 1 indicates whether access is barred for AC1 - bit 2 indicates whether access is barred for AC2 ... - bit 15 indicates whether access is barred for AC15 If a bit is set to 1, the corresponding Access Class is 'barred'. If a bit is set to 0, the corresponding Access Class is 'not barred'. If Access Class 10 is indicated as barred in a cell, UEs with Access Class 0 to 9 or without an IMSI are not allowed to initiate emergency calls in this cell. For UEs with Access Classes 11 to 15, emergency calls are not allowed if both Access Class 10 and the relevant Access Class (11 to 15) are barred. Otherwise, emergency calls are allowed for those UEs. Note: This value is used in SIB3 only when AccessClassRegulation is disabled in a cell. If AccessClassRegulation is enabled, only Access Classes 10 to 15 can be barred with this parameter.
Bit 0: Access Class 0, Bit 1: Access Class 1, Bit 2: Access Class 2, Bit 3: Access Class 3, Bit 4: Access Class 4, Bit 5: Access Class 5, Bit 6: Access Class 6, Bit 7: Access Class 7, Bit 8: Access Class 8, Bit 9: Access Class 9, Bit 10: Access Class 10, Bit 11: Access Class 11, Bit 12: Access Class 12, Bit 13: Access Class 13, Bit 14: Access Class 14, Bit 15: Access Class 15
Access Class Barred list' information defines whether access is barred for each of the 16 Access Classes (AC0...AC15). 'Access Class Barred list' uses a binary notation of 16 bits where - bit 0 indicates whether access is barred for AC0 - bit 1 indicates whether access is barred for AC1 - bit 2 indicates whether access is barred for AC2 ... - bit 15 indicates whether access is barred for AC15 If a bit is set to 1, the corresponding Access Class is 'barred'. If a bit is set to 0, the corresponding Access Class is 'not barred'. If Access Class 10 is indicated as barred in a cell, UEs with Access Class 0 to 9 or without an IMSI are not allowed to initiate emergency calls in this cell. For UEs with Access Classes 11 to 15, emergency calls are not allowed if both Access Class 10 and the relevant Access Class (11 to 15) are barred. Otherwise, emergency calls are allowed for those UEs. Note: This value is used in SIB3 only when AccessClassRegulation is disabled in a cell. If AccessClassRegulation is enabled, only Access Classes 10 to 15 can be barred with this parameter.
Bit 0: Access Class 0, Bit 1: Access Class 1, Bit 2: Access Class 2, Bit 3: Access Class 3, Bit 4: Access Class 4, Bit 5: Access Class 5, Bit 6: Access Class 6, Bit 7: Access Class 7, Bit 8: Access Class 8, Bit 9: Access Class 9, Bit 10: Access Class 10, Bit 11: Access Class 11, Bit 12: Access Class 12, Bit 13: Access Class 13, Bit 14: Access Class 14, Bit 15: Access Class 15
Access Class Barred list' information defines whether access is barred for each of the 16 Access Classes (AC0...AC15). 'Access Class Barred list' uses a binary notation of 16 bits where - bit 0 indicates whether access is barred for AC0 - bit 1 indicates whether access is barred for AC1 - bit 2 indicates whether access is barred for AC2 ... - bit 15 indicates whether access is barred for AC15 If a bit is set to 1, the corresponding Access Class is 'barred'. If a bit is set to 0, the corresponding Access Class is 'not barred'. If Access Class 10 is indicated as barred in a cell, UEs with Access Class 0 to 9 or without an IMSI are not allowed to initiate emergency calls in this cell. For UEs with Access Classes 11 to 15, emergency calls are not allowed if both Access Class 10 and the relevant Access Class (11 to 15) are barred. Otherwise, emergency calls are allowed for those UEs. Note: This value is used in SIB3 only when AccessClassRegulation is disabled in a cell. If AccessClassRegulation is enabled, only Access Classes 10 to 15 can be barred with this parameter.
Bit 0: Access Class 0, Bit 1: Access Class 1, Bit 2: Access Class 2, Bit 3: Access Class 3, Bit 4: Access Class 4, Bit 5: Access Class 5, Bit 6: Access Class 6, Bit 7: Access Class 7, Bit 8: Access Class 8, Bit 9: Access Class 9, Bit 10: Access Class 10, Bit 11: Access Class 11, Bit 12: Access Class 12, Bit 13: Access Class 13, Bit 14: Access Class 14, Bit 15: Access Class 15
Access Class Barred list' information defines whether access is barred for each of the 16 Access Classes (AC0...AC15). 'Access Class Barred list' uses a binary notation of 16 bits where - bit 0 indicates whether access is barred for AC0 - bit 1 indicates whether access is barred for AC1 - bit 2 indicates whether access is barred for AC2 ... - bit 15 indicates whether access is barred for AC15 If a bit is set to 1, the corresponding Access Class is 'barred'. If a bit is set to 0, the corresponding Access Class is 'not barred'. If Access Class 10 is indicated as barred in a cell, UEs with Access Class 0 to 9 or without an IMSI are not allowed to initiate emergency calls in this cell. For UEs with Access Classes 11 to 15, emergency calls are not allowed if both Access Class 10 and the relevant Access Class (11 to 15) are barred. Otherwise, emergency calls are allowed for those UEs. Note: This value is used in SIB3 only when AccessClassRegulation is disabled in a cell. If AccessClassRegulation is enabled, only Access Classes 10 to 15 can be barred with this parameter.
Bit 0: Access Class 0, Bit 1: Access Class 1, Bit 2: Access Class 2, Bit 3: Access Class 3, Bit 4: Access Class 4, Bit 5: Access Class 5, Bit 6: Access Class 6, Bit 7: Access Class 7, Bit 8: Access Class 8, Bit 9: Access Class 9, Bit 10: Access Class 10, Bit 11: Access Class 11, Bit 12: Access Class 12, Bit 13: Access Class 13, Bit 14: Access Class 14, Bit 15: Access Class 15
Access Class Barred list' information defines whether access is barred for each of the 16 Access Classes (AC0...AC15). 'Access Class Barred list' uses a binary notation of 16 bits where - bit 0 indicates whether access is barred for AC0 - bit 1 indicates whether access is barred for AC1 - bit 2 indicates whether access is barred for AC2 ... - bit 15 indicates whether access is barred for AC15 If a bit is set to 1, the corresponding Access Class is 'barred'. If a bit is set to 0, the corresponding Access Class is 'not barred'. If Access Class 10 is indicated as barred in a cell, UEs with Access Class 0 to 9 or without an IMSI are not allowed to initiate emergency calls in this cell. For UEs with Access Classes 11 to 15, emergency calls are not allowed if both Access Class 10 and the relevant Access Class (11 to 15) are barred. Otherwise, emergency calls are allowed for those UEs. Note: This value is used in SIB3 only when AccessClassRegulation is disabled in a cell. If AccessClassRegulation is enabled, only Access Classes 10 to 15 can be barred with this parameter.
Bit 0: Access Class 0, Bit 1: Access Class 1, Bit 2: Access Class 2, Bit 3: Access Class 3, Bit 4: Access Class 4, Bit 5: Access Class 5, Bit 6: Access Class 6, Bit 7: Access Class 7, Bit 8: Access Class 8, Bit 9: Access Class 9, Bit 10: Access Class 10, Bit 11: Access Class 11, Bit 12: Access Class 12, Bit 13: Access Class 13, Bit 14: Access Class 14, Bit 15: Access Class 15
Access Class Barred list' information defines whether access is barred for each of the 16 Access Classes (AC0...AC15). 'Access Class Barred list' uses a binary notation of 16 bits where - bit 0 indicates whether access is barred for AC0 - bit 1 indicates whether access is barred for AC1 - bit 2 indicates whether access is barred for AC2 ... - bit 15 indicates whether access is barred for AC15 If a bit is set to 1, the corresponding Access Class is 'barred'. If a bit is set to 0, the corresponding Access Class is 'not barred'. If Access Class 10 is indicated as barred in a cell, UEs with Access Class 0 to 9 or without an IMSI are not allowed to initiate emergency calls in this cell. For UEs with Access Classes 11 to 15, emergency calls are not allowed if both Access Class 10 and the relevant Access Class (11 to 15) are barred. Otherwise, emergency calls are allowed for those UEs. Note: This value is used in SIB3 only when AccessClassRegulation is disabled in a cell. If AccessClassRegulation is enabled, only Access Classes 10 to 15 can be barred with this parameter.
Bit 0: Access Class 0, Bit 1: Access Class 1, Bit 2: Access Class 2, Bit 3: Access Class 3, Bit 4: Access Class 4, Bit 5: Access Class 5, Bit 6: Access Class 6, Bit 7: Access Class 7, Bit 8: Access Class 8, Bit 9: Access Class 9, Bit 10: Access Class 10, Bit 11: Access Class 11, Bit 12: Access Class 12, Bit 13: Access Class 13, Bit 14: Access Class 14, Bit 15: Access Class 15
Access Class Barred list' information defines whether access is barred for each of the 16 Access Classes (AC0...AC15). 'Access Class Barred list' uses a binary notation of 16 bits where - bit 0 indicates whether access is barred for AC0 - bit 1 indicates whether access is barred for AC1 - bit 2 indicates whether access is barred for AC2 ... - bit 15 indicates whether access is barred for AC15 If a bit is set to 1, the corresponding Access Class is 'barred'. If a bit is set to 0, the corresponding Access Class is 'not barred'. If Access Class 10 is indicated as barred in a cell, UEs with Access Class 0 to 9 or without an IMSI are not allowed to initiate emergency calls in this cell. For UEs with Access Classes 11 to 15, emergency calls are not allowed if both Access Class 10 and the relevant Access Class (11 to 15) are barred. Otherwise, emergency calls are allowed for those UEs. Note: This value is used in SIB3 only when AccessClassRegulation is disabled in a cell. If AccessClassRegulation is enabled, only Access Classes 10 to 15 can be barred with this parameter.
Bit 0: Access Class 0, Bit 1: Access Class 1, Bit 2: Access Class 2, Bit 3: Access Class 3, Bit 4: Access Class 4, Bit 5: Access Class 5, Bit 6: Access Class 6, Bit 7: Access Class 7, Bit 8: Access Class 8, Bit 9: Access Class 9, Bit 10: Access Class 10, Bit 11: Access Class 11, Bit 12: Access Class 12, Bit 13: Access Class 13, Bit 14: Access Class 14, Bit 15: Access Class 15
Access Class Barred list' information defines whether access is barred for each of the 16 Access Classes (AC0...AC15). 'Access Class Barred list' uses a binary notation of 16 bits where - bit 0 indicates whether access is barred for AC0 - bit 1 indicates whether access is barred for AC1 - bit 2 indicates whether access is barred for AC2 ... - bit 15 indicates whether access is barred for AC15 If a bit is set to 1, the corresponding Access Class is 'barred'. If a bit is set to 0, the corresponding Access Class is 'not barred'. If Access Class 10 is indicated as barred in a cell, UEs with Access Class 0 to 9 or without an IMSI are not allowed to initiate emergency calls in this cell. For UEs with Access Classes 11 to 15, emergency calls are not allowed if both Access Class 10 and the relevant Access Class (11 to 15) are barred. Otherwise, emergency calls are allowed for those UEs. Note: This value is used in SIB3 only when AccessClassRegulation is disabled in a cell. If AccessClassRegulation is enabled, only Access Classes 10 to 15 can be barred with this parameter.
Bit 0: Access Class 0, Bit 1: Access Class 1, Bit 2: Access Class 2, Bit 3: Access Class 3, Bit 4: Access Class 4, Bit 5: Access Class 5, Bit 6: Access Class 6, Bit 7: Access Class 7, Bit 8: Access Class 8, Bit 9: Access Class 9, Bit 10: Access Class 10, Bit 11: Access Class 11, Bit 12: Access Class 12, Bit 13: Access Class 13, Bit 14: Access Class 14, Bit 15: Access Class 15
document.xls 文档密级:
04/17/2023 华为机密,未经许可不得扩散 第46页,共66页
CellBarred Not barred
Allowed
Tbarred 40 s
PrxNoise -101.9 dBm
PtxMaxHSDPA 38.5 dBm
0.5 s
640 ms
HHoEcNoCancelTime 640 ms
HHoEcNoThreshold -24~0 -12dbm
HHoEcNoCancel -24~0 -9dbm
HHoEcNoThreshold -24~0 -12dbm
HHoEcNoThreshold -24~0 -12dbm
HHoEcNoCancel -24~0 -9dbm
HHoEcNoCancel -24~0 -9dbm
HHoRscpThreshold -115~-25 -105dbm
HHoRscpCancel -115~-25 -102dbm
HHoRscpThreshold -115~-25 -105dbm
HHoRscpThreshold -115~-25 -105dbm
HHoRscpCancel -115~-25 -102dbm
HHoRscpCancel -115~-25 -102dbm
640 ms
HHoEcNoCancelTime 640 ms
HHoEcNoThreshold -24~0 -12dbm
Defines whether the cell is barred or not./nA barred cell is a cell where a UE is not allowed to camp on. Emergency calls shall be allowed in all cells whose barred status is 'not barred'. When cell status is 'barred', the UE is not permitted to select//re-select the cell, not even for emergency calls./nThis parameter is part of System Information Block 3.
Barred (0), Not barred (1)
IntraFreq_Cell_Reselect_Ind
Defines whether intra-frequency cell re-selection is allowed or not when the cell is barred./nWhen a cell's status is 'barred', the UE is not permitted to select//re-select this cell, except in some cases for an emergency call. If the 'Intra-frequency cell re-selection indicator' is set to value 'allowed', the UE may select another cell on the same frequency if selection//re-selection criteria are fulfilled. If the 'Intra-frequency cell re-selection indicator' is set to 'not allowed' the UE shall not re-select even a different cell on the same frequency as the barred cell. For emergency call, the Intra-frequency cell re-selection indicator IE' shall be ignored. 'Intra-frequency cell re-selection indicator' is part of SIB3//4 in the case the 'cell barred' indicator is true./nThis parameter is part of System Information Block 3.
Allowed (0), Not allowed (1)
When the cell is barred, the UE must check between the time interval ‘Cell barred period’, whether the status of the barred cell has changed./nThis parameter is part of the System Information Block 3.
10 s (0), 20 s (1), 40 s (2), 80 s (3), 160 s (4), 320 s (5), 640 s (6), 1280 s (7)
Defines the noise level in the BTS digital receiver when there is no load (thermal noise + noise figure). This parameter is needed in noise rise calculations.
-130...-50 dBm, step 0.1 dBm
The parameter defines the maximum allowed HSDPA transmission power.
-10...50 dBm, step 0.1 dBm
InterFreqMeasRepInterval
This parameter determines the measurement reporting interval for periodical inter-frequency measurements.
0.5 s (2), 1 s (3), 2 s (4), 3 s (5), 4 s (6)
HHoEcNoTimeHysteresis
If the inter-frequency or inter-RAT (GSM) handover caused by low measured absolute CPICH Ec/No is enabled, the UE transmits an event 1F triggered measurement report to the RNC when the CPICH Ec/No measurement result of an active set cell becomes worse than the threshold HHoEcNoThreshold. The parameter HHoEcNoTimeHysteresis determines the time period during which the CPICH Ec/No of the active set cell must stay worse than the threshold HHoEcNoThreshold before the UE can trigger the reporting event 1F. When the measured CPICH Ec/No of all active set cells has become worse than the threshold in question, the RNC starts inter-frequency or inter-RAT (GSM) measurements in compressed mode for the purpose of hard handover.
0 ms (0), 10 ms (1), 20 ms (2), 40 ms (3), 60 ms (4), 80 ms (5), 100 ms (6), 120 ms (7), 160 ms (8), 200 ms (9), 240 ms (10), 320 ms (11), 640 ms (12), 1280 ms (13), 2560 ms (14), 5000 ms (15)
If the inter-frequency or inter-RAT (GSM) handover caused by low measured absolute CPICH Ec/No is enabled, the RNC starts the inter-frequency or GSM measurement in compressed mode when all active set cells have triggered the reporting event 1F for CPICH Ec/No. The RNC cancels the event 1F of an active set cell if the CPICH Ec/No measurement result of the active set cell becomes better than or equal to the threshold HHoEcNoCancel and the UE transmits the corresponding event 1E triggered Measurement Report to the RNC. The parameter HHoEcNoCancelTime determines the time period during which the CPICH Ec/No of the active set cell must stay better than the threshold HHoEcNoCancel before the UE can trigger the reporting event 1E. Note that once the RNC has started the inter-frequency or inter-RAT (GSM) measurement for the purpose of hard handover due to low measured absolute CPICH Ec/No, the RNC does not break off the ongoing measurement, even if one or more active set cells trigger the reporting event 1E for CPICH Ec/No.
0 ms (0), 10 ms (1), 20 ms (2), 40 ms (3), 60 ms (4), 80 ms (5), 100 ms (6), 120 ms (7), 160 ms (8), 200 ms (9), 240 ms (10), 320 ms (11), 640 ms (12), 1280 ms (13), 2560 ms (14), 5000 ms (15)
If the inter-frequency or inter-RAT (GSM) handover caused by low measured absolute CPICH Ec/No is enabled, the UE transmits an event 1F triggered measurement report to the RNC when the CPICH Ec/No measurement result of an active set cell becomes worse than or equal to an absolute CPICH Ec/No threshold. The parameter HHoEcNoThreshold determines the absolute CPICH Ec/No threshold which is used by the UE to trigger the reporting event 1F. When the measured CPICH Ec/No of all active set cells has become worse than or equal to the threshold in question, the RNC starts inter-frequency or inter-RAT (GSM) measurements in compressed mode for the purpose of hard handover.
If the inter-frequency or inter-RAT (GSM) handover caused by low measured absolute CPICH Ec/No is enabled, the RNC starts the inter-frequency or GSM measurement in compressed mode when all active set cells have triggered the reporting event 1F for CPICH Ec/No. The RNC cancels the event 1F of an active set cell if the CPICH Ec/No measurement result of the active set cell becomes better than or equal to the threshold HHoEcNoCancel and the UE transmits the corresponding event 1E triggered Measurement Report to the RNC. Note that once the RNC has started the inter-frequency or inter-RAT (GSM) measurement for the purpose of hard handover due to low measured absolute CPICH Ec/No, the RNC does not break off the ongoing measurement, even if one or more active set cells trigger the reporting event 1E for CPICH Ec/No.
If the inter-frequency or inter-RAT (GSM) handover caused by low measured absolute CPICH Ec/No is enabled, the UE transmits an event 1F triggered measurement report to the RNC when the CPICH Ec/No measurement result of an active set cell becomes worse than or equal to an absolute CPICH Ec/No threshold. The parameter HHoEcNoThreshold determines the absolute CPICH Ec/No threshold which is used by the UE to trigger the reporting event 1F. When the measured CPICH Ec/No of all active set cells has become worse than or equal to the threshold in question, the RNC starts inter-frequency or inter-RAT (GSM) measurements in compressed mode for the purpose of hard handover.
If the inter-frequency or inter-RAT (GSM) handover caused by low measured absolute CPICH Ec/No is enabled, the UE transmits an event 1F triggered measurement report to the RNC when the CPICH Ec/No measurement result of an active set cell becomes worse than or equal to an absolute CPICH Ec/No threshold. The parameter HHoEcNoThreshold determines the absolute CPICH Ec/No threshold which is used by the UE to trigger the reporting event 1F. When the measured CPICH Ec/No of all active set cells has become worse than or equal to the threshold in question, the RNC starts inter-frequency or inter-RAT (GSM) measurements in compressed mode for the purpose of hard handover.
If the inter-frequency or inter-RAT (GSM) handover caused by low measured absolute CPICH Ec/No is enabled, the RNC starts the inter-frequency or GSM measurement in compressed mode when all active set cells have triggered the reporting event 1F for CPICH Ec/No. The RNC cancels the event 1F of an active set cell if the CPICH Ec/No measurement result of the active set cell becomes better than or equal to the threshold HHoEcNoCancel and the UE transmits the corresponding event 1E triggered Measurement Report to the RNC. Note that once the RNC has started the inter-frequency or inter-RAT (GSM) measurement for the purpose of hard handover due to low measured absolute CPICH Ec/No, the RNC does not break off the ongoing measurement, even if one or more active set cells trigger the reporting event 1E for CPICH Ec/No.
If the inter-frequency or inter-RAT (GSM) handover caused by low measured absolute CPICH Ec/No is enabled, the RNC starts the inter-frequency or GSM measurement in compressed mode when all active set cells have triggered the reporting event 1F for CPICH Ec/No. The RNC cancels the event 1F of an active set cell if the CPICH Ec/No measurement result of the active set cell becomes better than or equal to the threshold HHoEcNoCancel and the UE transmits the corresponding event 1E triggered Measurement Report to the RNC. Note that once the RNC has started the inter-frequency or inter-RAT (GSM) measurement for the purpose of hard handover due to low measured absolute CPICH Ec/No, the RNC does not break off the ongoing measurement, even if one or more active set cells trigger the reporting event 1E for CPICH Ec/No.
If the inter-frequency or inter-RAT (GSM) handover caused by low measured CPICH RSCP is enabled, the UE transmits an event 1F triggered measurement report to the RNC when the CPICH RSCP measurement result of an active set cell becomes worse than or equal to an absolute CPICH RSCP threshold. The parameter HHoRscpThreshold determines the absolute CPICH RSCP threshold which is used by the UE to trigger the reporting event 1F. When the measured CPICH RSCP of all active set cells has become worse than or equal to the threshold in question, the RNC starts inter-frequency or inter-RAT (GSM) measurements in compressed mode for the purpose of hard handover.
If the inter-frequency or inter-RAT (GSM) handover caused by low measured absolute CPICH RSCP is enabled, the RNC starts the inter-frequency or GSM measurement in compressed mode when all active set cells have triggered the reporting event 1F for CPICH RSCP. The RNC cancels the event 1F of an active set cell, if the CPICH RSCP measurement result of the active set cell becomes better than or equal to the threshold HHoRscpCancel and the UE transmits the corresponding event 1E triggered measurement report to the RNC. Note, that once the RNC has started the inter-frequency or inter-RAT (GSM) measurement for the purpose of hard handover due to low measured absolute CPICH RSCP, the RNC does not break off the ongoing measurement, even if one or more active set cells trigger the reporting event 1E for CPICH RSCP.
If the inter-frequency or inter-RAT (GSM) handover caused by low measured CPICH RSCP is enabled, the UE transmits an event 1F triggered measurement report to the RNC when the CPICH RSCP measurement result of an active set cell becomes worse than or equal to an absolute CPICH RSCP threshold. The parameter HHoRscpThreshold determines the absolute CPICH RSCP threshold which is used by the UE to trigger the reporting event 1F. When the measured CPICH RSCP of all active set cells has become worse than or equal to the threshold in question, the RNC starts inter-frequency or inter-RAT (GSM) measurements in compressed mode for the purpose of hard handover.
If the inter-frequency or inter-RAT (GSM) handover caused by low measured CPICH RSCP is enabled, the UE transmits an event 1F triggered measurement report to the RNC when the CPICH RSCP measurement result of an active set cell becomes worse than or equal to an absolute CPICH RSCP threshold. The parameter HHoRscpThreshold determines the absolute CPICH RSCP threshold which is used by the UE to trigger the reporting event 1F. When the measured CPICH RSCP of all active set cells has become worse than or equal to the threshold in question, the RNC starts inter-frequency or inter-RAT (GSM) measurements in compressed mode for the purpose of hard handover.
If the inter-frequency or inter-RAT (GSM) handover caused by low measured absolute CPICH RSCP is enabled, the RNC starts the inter-frequency or GSM measurement in compressed mode when all active set cells have triggered the reporting event 1F for CPICH RSCP. The RNC cancels the event 1F of an active set cell, if the CPICH RSCP measurement result of the active set cell becomes better than or equal to the threshold HHoRscpCancel and the UE transmits the corresponding event 1E triggered measurement report to the RNC. Note, that once the RNC has started the inter-frequency or inter-RAT (GSM) measurement for the purpose of hard handover due to low measured absolute CPICH RSCP, the RNC does not break off the ongoing measurement, even if one or more active set cells trigger the reporting event 1E for CPICH RSCP.
If the inter-frequency or inter-RAT (GSM) handover caused by low measured absolute CPICH RSCP is enabled, the RNC starts the inter-frequency or GSM measurement in compressed mode when all active set cells have triggered the reporting event 1F for CPICH RSCP. The RNC cancels the event 1F of an active set cell, if the CPICH RSCP measurement result of the active set cell becomes better than or equal to the threshold HHoRscpCancel and the UE transmits the corresponding event 1E triggered measurement report to the RNC. Note, that once the RNC has started the inter-frequency or inter-RAT (GSM) measurement for the purpose of hard handover due to low measured absolute CPICH RSCP, the RNC does not break off the ongoing measurement, even if one or more active set cells trigger the reporting event 1E for CPICH RSCP.
HHoEcNoTimeHysteresis
If the inter-frequency or inter-RAT (GSM) handover caused by low measured absolute CPICH Ec/No is enabled, the UE transmits an event 1F triggered measurement report to the RNC when the CPICH Ec/No measurement result of an active set cell becomes worse than the threshold HHoEcNoThreshold. The parameter HHoEcNoTimeHysteresis determines the time period during which the CPICH Ec/No of the active set cell must stay worse than the threshold HHoEcNoThreshold before the UE can trigger the reporting event 1F. When the measured CPICH Ec/No of all active set cells has become worse than the threshold in question, the RNC starts inter-frequency or inter-RAT (GSM) measurements in compressed mode for the purpose of hard handover.
0 ms (0), 10 ms (1), 20 ms (2), 40 ms (3), 60 ms (4), 80 ms (5), 100 ms (6), 120 ms (7), 160 ms (8), 200 ms (9), 240 ms (10), 320 ms (11), 640 ms (12), 1280 ms (13), 2560 ms (14), 5000 ms (15)
If the inter-frequency or inter-RAT (GSM) handover caused by low measured absolute CPICH Ec/No is enabled, the RNC starts the inter-frequency or GSM measurement in compressed mode when all active set cells have triggered the reporting event 1F for CPICH Ec/No. The RNC cancels the event 1F of an active set cell if the CPICH Ec/No measurement result of the active set cell becomes better than or equal to the threshold HHoEcNoCancel and the UE transmits the corresponding event 1E triggered Measurement Report to the RNC. The parameter HHoEcNoCancelTime determines the time period during which the CPICH Ec/No of the active set cell must stay better than the threshold HHoEcNoCancel before the UE can trigger the reporting event 1E. Note that once the RNC has started the inter-frequency or inter-RAT (GSM) measurement for the purpose of hard handover due to low measured absolute CPICH Ec/No, the RNC does not break off the ongoing measurement, even if one or more active set cells trigger the reporting event 1E for CPICH Ec/No.
0 ms (0), 10 ms (1), 20 ms (2), 40 ms (3), 60 ms (4), 80 ms (5), 100 ms (6), 120 ms (7), 160 ms (8), 200 ms (9), 240 ms (10), 320 ms (11), 640 ms (12), 1280 ms (13), 2560 ms (14), 5000 ms (15)
If the inter-frequency or inter-RAT (GSM) handover caused by low measured absolute CPICH Ec/No is enabled, the UE transmits an event 1F triggered measurement report to the RNC when the CPICH Ec/No measurement result of an active set cell becomes worse than or equal to an absolute CPICH Ec/No threshold. The parameter HHoEcNoThreshold determines the absolute CPICH Ec/No threshold which is used by the UE to trigger the reporting event 1F. When the measured CPICH Ec/No of all active set cells has become worse than or equal to the threshold in question, the RNC starts inter-frequency or inter-RAT (GSM) measurements in compressed mode for the purpose of hard handover.
document.xls 文档密级:
04/17/2023 华为机密,未经许可不得扩散 第47页,共66页
HHoEcNoCancel -24~0 -9dbm
HHoEcNoThreshold -24~0 -12dbm
HHoEcNoThreshold -24~0 -12dbm
HHoEcNoCancel -24~0 -9dbm
HHoEcNoCancel -24~0 -9dbm
HHoRscpThreshold -115~-25 -105dbm
HHoRscpCancel -115~-25 -102dbm
HHoRscpThreshold -115~-25 -105dbm
HHoRscpThreshold -115~-25 -105dbm
HHoRscpCancel -115~-25 -102dbm
HHoRscpCancel -115~-25 -102dbm
AdjgRxLevMinHO 8
AdjgRxLevMinHO 8
AdjgRxLevMinHO 8
AdditionWindow 4 dB
AdditionWindow 4 dB
AdditionWindow 4 dB
DropWindow 6 dB
DropWindow 6 dB
DropWindow 6 dB
AdditionTime 100 ms
DropTime 640 ms
If the inter-frequency or inter-RAT (GSM) handover caused by low measured absolute CPICH Ec/No is enabled, the RNC starts the inter-frequency or GSM measurement in compressed mode when all active set cells have triggered the reporting event 1F for CPICH Ec/No. The RNC cancels the event 1F of an active set cell if the CPICH Ec/No measurement result of the active set cell becomes better than or equal to the threshold HHoEcNoCancel and the UE transmits the corresponding event 1E triggered Measurement Report to the RNC. Note that once the RNC has started the inter-frequency or inter-RAT (GSM) measurement for the purpose of hard handover due to low measured absolute CPICH Ec/No, the RNC does not break off the ongoing measurement, even if one or more active set cells trigger the reporting event 1E for CPICH Ec/No.
If the inter-frequency or inter-RAT (GSM) handover caused by low measured absolute CPICH Ec/No is enabled, the UE transmits an event 1F triggered measurement report to the RNC when the CPICH Ec/No measurement result of an active set cell becomes worse than or equal to an absolute CPICH Ec/No threshold. The parameter HHoEcNoThreshold determines the absolute CPICH Ec/No threshold which is used by the UE to trigger the reporting event 1F. When the measured CPICH Ec/No of all active set cells has become worse than or equal to the threshold in question, the RNC starts inter-frequency or inter-RAT (GSM) measurements in compressed mode for the purpose of hard handover.
If the inter-frequency or inter-RAT (GSM) handover caused by low measured absolute CPICH Ec/No is enabled, the UE transmits an event 1F triggered measurement report to the RNC when the CPICH Ec/No measurement result of an active set cell becomes worse than or equal to an absolute CPICH Ec/No threshold. The parameter HHoEcNoThreshold determines the absolute CPICH Ec/No threshold which is used by the UE to trigger the reporting event 1F. When the measured CPICH Ec/No of all active set cells has become worse than or equal to the threshold in question, the RNC starts inter-frequency or inter-RAT (GSM) measurements in compressed mode for the purpose of hard handover.
If the inter-frequency or inter-RAT (GSM) handover caused by low measured absolute CPICH Ec/No is enabled, the RNC starts the inter-frequency or GSM measurement in compressed mode when all active set cells have triggered the reporting event 1F for CPICH Ec/No. The RNC cancels the event 1F of an active set cell if the CPICH Ec/No measurement result of the active set cell becomes better than or equal to the threshold HHoEcNoCancel and the UE transmits the corresponding event 1E triggered Measurement Report to the RNC. Note that once the RNC has started the inter-frequency or inter-RAT (GSM) measurement for the purpose of hard handover due to low measured absolute CPICH Ec/No, the RNC does not break off the ongoing measurement, even if one or more active set cells trigger the reporting event 1E for CPICH Ec/No.
If the inter-frequency or inter-RAT (GSM) handover caused by low measured absolute CPICH Ec/No is enabled, the RNC starts the inter-frequency or GSM measurement in compressed mode when all active set cells have triggered the reporting event 1F for CPICH Ec/No. The RNC cancels the event 1F of an active set cell if the CPICH Ec/No measurement result of the active set cell becomes better than or equal to the threshold HHoEcNoCancel and the UE transmits the corresponding event 1E triggered Measurement Report to the RNC. Note that once the RNC has started the inter-frequency or inter-RAT (GSM) measurement for the purpose of hard handover due to low measured absolute CPICH Ec/No, the RNC does not break off the ongoing measurement, even if one or more active set cells trigger the reporting event 1E for CPICH Ec/No.
If the inter-frequency or inter-RAT (GSM) handover caused by low measured CPICH RSCP is enabled, the UE transmits an event 1F triggered measurement report to the RNC when the CPICH RSCP measurement result of an active set cell becomes worse than or equal to an absolute CPICH RSCP threshold. The parameter HHoRscpThreshold determines the absolute CPICH RSCP threshold which is used by the UE to trigger the reporting event 1F. When the measured CPICH RSCP of all active set cells has become worse than or equal to the threshold in question, the RNC starts inter-frequency or inter-RAT (GSM) measurements in compressed mode for the purpose of hard handover.
If the inter-frequency or inter-RAT (GSM) handover caused by low measured absolute CPICH RSCP is enabled, the RNC starts the inter-frequency or GSM measurement in compressed mode when all active set cells have triggered the reporting event 1F for CPICH RSCP. The RNC cancels the event 1F of an active set cell, if the CPICH RSCP measurement result of the active set cell becomes better than or equal to the threshold HHoRscpCancel and the UE transmits the corresponding event 1E triggered measurement report to the RNC. Note, that once the RNC has started the inter-frequency or inter-RAT (GSM) measurement for the purpose of hard handover due to low measured absolute CPICH RSCP, the RNC does not break off the ongoing measurement, even if one or more active set cells trigger the reporting event 1E for CPICH RSCP.
If the inter-frequency or inter-RAT (GSM) handover caused by low measured CPICH RSCP is enabled, the UE transmits an event 1F triggered measurement report to the RNC when the CPICH RSCP measurement result of an active set cell becomes worse than or equal to an absolute CPICH RSCP threshold. The parameter HHoRscpThreshold determines the absolute CPICH RSCP threshold which is used by the UE to trigger the reporting event 1F. When the measured CPICH RSCP of all active set cells has become worse than or equal to the threshold in question, the RNC starts inter-frequency or inter-RAT (GSM) measurements in compressed mode for the purpose of hard handover.
If the inter-frequency or inter-RAT (GSM) handover caused by low measured CPICH RSCP is enabled, the UE transmits an event 1F triggered measurement report to the RNC when the CPICH RSCP measurement result of an active set cell becomes worse than or equal to an absolute CPICH RSCP threshold. The parameter HHoRscpThreshold determines the absolute CPICH RSCP threshold which is used by the UE to trigger the reporting event 1F. When the measured CPICH RSCP of all active set cells has become worse than or equal to the threshold in question, the RNC starts inter-frequency or inter-RAT (GSM) measurements in compressed mode for the purpose of hard handover.
If the inter-frequency or inter-RAT (GSM) handover caused by low measured absolute CPICH RSCP is enabled, the RNC starts the inter-frequency or GSM measurement in compressed mode when all active set cells have triggered the reporting event 1F for CPICH RSCP. The RNC cancels the event 1F of an active set cell, if the CPICH RSCP measurement result of the active set cell becomes better than or equal to the threshold HHoRscpCancel and the UE transmits the corresponding event 1E triggered measurement report to the RNC. Note, that once the RNC has started the inter-frequency or inter-RAT (GSM) measurement for the purpose of hard handover due to low measured absolute CPICH RSCP, the RNC does not break off the ongoing measurement, even if one or more active set cells trigger the reporting event 1E for CPICH RSCP.
If the inter-frequency or inter-RAT (GSM) handover caused by low measured absolute CPICH RSCP is enabled, the RNC starts the inter-frequency or GSM measurement in compressed mode when all active set cells have triggered the reporting event 1F for CPICH RSCP. The RNC cancels the event 1F of an active set cell, if the CPICH RSCP measurement result of the active set cell becomes better than or equal to the threshold HHoRscpCancel and the UE transmits the corresponding event 1E triggered measurement report to the RNC. Note, that once the RNC has started the inter-frequency or inter-RAT (GSM) measurement for the purpose of hard handover due to low measured absolute CPICH RSCP, the RNC does not break off the ongoing measurement, even if one or more active set cells trigger the reporting event 1E for CPICH RSCP.
This parameter determines the minimum required GSM RSSI level which the averaged RSSI value of the GSMneighbour cell must exceed before the coverage (or quality) reason handover to GSM is possible.
-110...-47 dBm, step 1 dBm
This parameter determines the minimum required GSM RSSI level which the averaged RSSI value of the GSMneighbour cell must exceed before the coverage (or quality) reason handover to GSM is possible.
-110...-47 dBm, step 1 dBm
This parameter determines the minimum required GSM RSSI level which the averaged RSSI value of the GSMneighbour cell must exceed before the coverage (or quality) reason handover to GSM is possible.
-110...-47 dBm, step 1 dBm
Addition Window determines the relative threshold (A_Win) used by the UE to calculate the reporting range of event 1A. The threshold is either relative to the CPICH Ec/No measurement result of the best active set cell (M_best), or to the sum of active set measurement results (M_sum), depending on the value of the parameter Active Set Weighting Coefficient (W). When the CPICH Ec/No measurement result of a monitored cell (M_new) enters the reporting range, the UE transmits a Measurement Report to the RNC in order to add the monitored cell into the active set: M_new >= W * M_sum + ( 1 - W )* M_best - A_Win This parameter is part of System Information Block 11/12.
0...14.5 dB, step 0.5 dB
Addition Window determines the relative threshold (A_Win) used by the UE to calculate the reporting range of event 1A. The threshold is either relative to the CPICH Ec/No measurement result of the best active set cell (M_best), or to the sum of active set measurement results (M_sum), depending on the value of the parameter Active Set Weighting Coefficient (W). When the CPICH Ec/No measurement result of a monitored cell (M_new) enters the reporting range, the UE transmits a Measurement Report to the RNC in order to add the monitored cell into the active set: M_new >= W * M_sum + ( 1 - W )* M_best - A_Win This parameter is part of System Information Block 11/12.
0...14.5 dB, step 0.5 dB
Addition Window determines the relative threshold (A_Win) used by the UE to calculate the reporting range of event 1A. The threshold is either relative to the CPICH Ec/No measurement result of the best active set cell (M_best), or to the sum of active set measurement results (M_sum), depending on the value of the parameter Active Set Weighting Coefficient (W). When the CPICH Ec/No measurement result of a monitored cell (M_new) enters the reporting range, the UE transmits a Measurement Report to the RNC in order to add the monitored cell into the active set: M_new >= W * M_sum + ( 1 - W )* M_best - A_Win This parameter is part of System Information Block 11/12.
0...14.5 dB, step 0.5 dB
Drop Window determines the relative threshold (D_Win) which is used by the UE to calculate the reporting range of event 1B. The threshold is either relative to the CPICH Ec/No measurement result of the best active set cell (M_best) or to the sum of active set measurement results (M_sum), depending on the value of the parameter Active Set Weighting Coefficient (W). When the CPICH Ec/No measurement result of an active set cell (M_old) leaves the reporting range, the UE transmits a Measurement Report to the RNC in order to remove the cell from the active set: M_old <= W * M_sum + ( 1 - W )* M_best - D_Win This parameter is part of System Information Block 11/12.
0...14.5 dB, step 0.5 dB
Drop Window determines the relative threshold (D_Win) which is used by the UE to calculate the reporting range of event 1B. The threshold is either relative to the CPICH Ec/No measurement result of the best active set cell (M_best) or to the sum of active set measurement results (M_sum), depending on the value of the parameter Active Set Weighting Coefficient (W). When the CPICH Ec/No measurement result of an active set cell (M_old) leaves the reporting range, the UE transmits a Measurement Report to the RNC in order to remove the cell from the active set: M_old <= W * M_sum + ( 1 - W )* M_best - D_Win This parameter is part of System Information Block 11/12.
0...14.5 dB, step 0.5 dB
Drop Window determines the relative threshold (D_Win) which is used by the UE to calculate the reporting range of event 1B. The threshold is either relative to the CPICH Ec/No measurement result of the best active set cell (M_best) or to the sum of active set measurement results (M_sum), depending on the value of the parameter Active Set Weighting Coefficient (W). When the CPICH Ec/No measurement result of an active set cell (M_old) leaves the reporting range, the UE transmits a Measurement Report to the RNC in order to remove the cell from the active set: M_old <= W * M_sum + ( 1 - W )* M_best - D_Win This parameter is part of System Information Block 11/12.
0...14.5 dB, step 0.5 dB
When a monitored cell enters the reporting range (addition window), the cell must continuously stay within the reporting range for a given period of time before the UE can send a Measurement Report to the RNC in order to add the cell into the active set (event 1A). The length of this period is controlled by the parameter Addition Time. This parameter is part of System Information Block 11/12.
0 ms (0), 10 ms (1), 20 ms (2), 40 ms (3), 60 ms (4), 80 ms (5), 100 ms (6), 120 ms (7), 160 ms (8), 200 ms (9), 240 ms (10), 320 ms (11), 640 ms (12), 1280 ms (13), 2560 ms (14), 5000 ms (15)
When an active set cell leaves the reporting range (drop window), the cell must continuously stay outside the reporting range for a given period of time before the UE can send a Measurement Report to the RNC in order to remove the cell from the active set (event 1B). The length of this period is controlled by the parameter Drop Time. This parameter is part of System Information Block 11/12.
0 ms (0), 10 ms (1), 20 ms (2), 40 ms (3), 60 ms (4), 80 ms (5), 100 ms (6), 120 ms (7), 160 ms (8), 200 ms (9), 240 ms (10), 320 ms (11), 640 ms (12), 1280 ms (13), 2560 ms (14), 5000 ms (15)
document.xls 文档密级:
04/17/2023 华为机密,未经许可不得扩散 第48页,共66页
MaxActiveSetSize 2...3, step 1 3
Qhyst1 0 dB
Qhyst1 0 dB
Qhyst2 2 dB
Qhyst2 2 dB
Treselection 2 s
QqualMin -18 dB
QrxlevMin -115 dBm
Sintrasearch 10db
Sintersearch 8 dB
Ssearch_RAT 4 dB
PTxPICH -8 dB
PtxAICH -8 dB
CS_T3212 0 decihours
PS_NMO
UTRAN_DRX_length 320 ms
T302 2000 ms
N302 0...7, step 1 7
T309 1...8 s, step 1 s 8
T312conn 6s
N312 4 (2)
T313 3 s
N313 20 (4)
T314 4s
T315 180 s
N315 1
This parameter determines the maximum number of cells which can participate in a soft/softer handover. Reporting deactivation threshold indicates the maximum number of cells allowed in the active set in order for the event 1A to trigger. The RNC calculates the deactivation threshold from the parameter MaxActiveSetSize: Reporting Deactivation Threshold = MaxActiveSetSize - 1 Reporting Deactivation Threshold parameter is part of System Information Block 11/12. Replacement activation threshold information element indicates the minimum number of cells allowed in the active set in order for the event 1C to trigger. The threshold equals to the maximum size of the active set which is controlled with the parameter MaxActiveSetSize. Replacement Activation Threshold parameter is part of System Information Block 11/12.
Qhyst1 is used for TDD and GSM cells, and for FDD cells when cell selection and re-selection quality measure is set to CPICH RSCP./nThis parameter is part of System Information Block 3.
0...40 dB, step 2 dB
Qhyst1 is used for TDD and GSM cells, and for FDD cells when cell selection and re-selection quality measure is set to CPICH RSCP./nThis parameter is part of System Information Block 3.
0...40 dB, step 2 dB
Qhyst2 is used for TDD and GSM cells, and for FDD cells when cell selection and re-selection quality measure is set to CPICH ECNO./nThis parameter is part of System Information Block 3.
0...40 dB, step 2 dB
Qhyst2 is used for TDD and GSM cells, and for FDD cells when cell selection and re-selection quality measure is set to CPICH ECNO./nThis parameter is part of System Information Block 3.
0...40 dB, step 2 dB
The UE triggers the reselection of a new cell if the cell reselection criteria are fulfilled during the time interval Treselection./nThis parameter is part of System Information Block 3.
0...31 s, step 1 sThe minimum required quality
level in the cell (Ec//No)./nThis parameter is part of System Information Block 3.
-24...0 dB, step 1 dB
Determines the minimum required RSSI level which the measurement result of the GSM neighbour cell must exceed before the cell re-selection becomes possible./nThis parameter is part of System Information Block 11&12.
-115...-25 dBm, step 2 dBm
The threshold for intra-frequency measurements, and for the HCS measurement rules./nNote: If no threshold is given, MS performs measurements./nThis parameter is part of System Information Block 3.
0...20 dB, step 2 dB
The threshold for inter-frequency measurements, and for the HCS measurement rules. /nNote: If no threshold is given, MS performs measurements./nThis parameter is part of System Information Block 3.
0...20 dB, step 2 dB
The RAT-specific threshold for inter-RAT measurement rules./nNote: If no threshold is given, MS performs measurements./nThis parameter is part of System Information Block 3.
0...20 dB, step 2 dB
This is the transmission power of the PICH channel. It carries the paging indicators which tell the UE to read the paging message from the associated secondary CCPCH. The transmission power value is relative to the CPICH transmission power. It may depend on the number of paging indicators (PI) per frame. The following table shows the recommended values for the different cases N. PI per frame (NP), Repetition of PICH bits, Power relative to CPICH (dB): 18, 16, -10 36, 8, -10 72, 4, -8 144, 2, -5 This parameter is part of System Information Block 5.
-10...5 dB, step 1 dB
This is the transmission power of one Aquisition Indicator (AI) compared to CPICH power. If a WCDMA BTS transmits a large number of AIs, then the total power of AICH increases. The AICH consists of a repeated sequence of 15 consecutive Access Slots (AS), each one 5120 chips in length. Each access slot consists of two parts: an Acquisition Indicator (AI) part consisting of 32 real-valued symbols, and a second part, 1024 chips in length, which has no transmission and is not formally part of the AICH. This second part of the slot is reserved for possible use by CSICH, or possible future use by other physical channels. The spreading factor (SF) used for the channelisation of the AICH is 256, and the phase reference for the AICH is the P-CPICH. This parameter is part of System Information Block 5.
-22...5 dB, step 1 dB
The timeout value, in decihours (6 min), for periodic location updating. Given only for CS domain. (Part of CS domain specific NAS System information in SIB1). /nThe value 0 is used for an infinite timeout value, that is, periodic location updating is not used./nThis parameter is part of System Information Block 1.
0...255 decihours, step 1 decihours
CSAttachDetachAllowed
Defines whether IMSI attach and detach are allowed or not. /n0 = MSs shall not apply IMSI attach and detach procedure, /n1 = MSs shall apply IMSI attach and detach procedure. /nParameter is given only for CS domain. (Part of CS domain specific NAS System information in SIB1.)
IMSI attach/detach not allowed (0), IMSI attach/detach allowed (1)
IMSI attach/detach allowed
In Operation Mode I it is possible to have combined CS and PS side paging via SGSN. In Operation Mode II the combined paging procedure is not possible (and neither are combined attach procedures). Used only for the PS domain. NMO is part of PS CN domain specific NAS System information in System Information Block 1.
Network Mode of Operation I (0), Network Mode ofOperation II (1)
Network Mode ofOperation II (1)
The DRX cycle length used by UTRAN to count paging occasions for discontinuous reception./n(The duration of the DRX cycle is 2 <power> k frames, where 'k' is the used DRX cycle length coefficient for UTRAN.)
80 ms (3), 160 ms (4), 320 ms (5), 640 ms (6), 1280 ms (7), 2560 ms (8), 5120 ms (9)
The CELL UPDATE/URA UPDATE retransmission timer (MS timer). This parameter is part of System Information Block 1.
1000 ms (5), 1200 ms (6), 1400 ms (7), 1600 ms (8), 1800 ms (9), 2000 ms (10), 3000 ms (11), 4000 ms (12), 6000 ms (13), 8000 ms (14)
CELL UPDATE/URA UPDATE retransmission counter (MS counter). This parameter is part of System Information Block 1.
The timer for supervising successful connection establishment in case of an inter-RAT cell re-selection (MS timer).
The timer for supervising successful establishment of a physical channel (MS timer used in idle mode).
1...15 s, step 1 s
This parameter defines the maximum number of 'in sync' indications received from L1 during the establishment of a physical channel (UE counter used in idle mode)./nThis parameter is part of System Information Block 1.
1 (0), 2 (1), 4 (2), 10 (3), 20 (4), 50 (5), 100 (6), 200 (7), 400 (8), 600 (9), 800 (10), 1000 (11)
The radio link failure timer (MS timer). This parameter is part of System Information Block 1.
0...15 s, step 1 s
This parameter defines the maximum number of successive "out of sync" indications received from L1 (MS counter). This parameter is part of System Information Block 1.
1 (0), 2 (1), 4 (2), 10 (3), 20 (4), 50 (5), 100 (6), 200 (7)
The RRC connection re-establishment timer usedfor service-types allowing notably shorter re-establishmenttimes than the UE-timer T315. Currentlythis timer is used for CS service bearers only.UEs prior 3GPP REL6 use this timer also for supervisingthe RRC connection re-establishment ofstandalone (NAS) signaling connection towardsboth the CN domains.This parameter is part of System Information Block1.
0s (0), 2s (1), 4s (2), 6s (3), 8s (4), 12s (5), 16s (6),20s (7)
The RRC connection re-establishment timer for AM bearers (UE timer). This parameter is part of System Information Block 1.
0 s (0), 10 s (1), 30 s (2), 60 s (3), 180 s (4), 600 s (5), 1200 s (6), 1800 s (7)
This parameter defines the maximum number of successive "in sync" indications received from L1 while T313 is being activated (UE counter). This parameter is part of System Information Block 1.
1 (0), 2 (1), 4 (2), 10 (3), 20 (4), 50 (5), 100 (6), 200 (7)
document.xls 文档密级:
04/17/2023 华为机密,未经许可不得扩散 第49页,共66页
PtxSCCPCH1 0 dB
UTRAN_DRX_length 320 ms
T300 2000 ms
N300 0...7, step 1 3
T312 6 s
N312 4 (2)
0.5 s
640 ms
HHoEcNoCancelTime 640 ms
HHoEcNoThreshold -24~0 -12dbm
HHoEcNoCancel -24~0 -9dbm
HHoEcNoThreshold -24~0 -12dbm
HHoEcNoThreshold -24~0 -12dbm
HHoEcNoCancel -24~0 -9dbm
HHoEcNoCancel -24~0 -9dbm
HHoRscpThreshold -115~-25 -105dbm
HHoRscpCancel -115~-25 -102dbm
HHoRscpThreshold -115~-25 -105dbm
HHoRscpThreshold -115~-25 -105dbm
This is the transmission power of the S-CCPCH channel, which carries: - a PCH (containing PCCH), a FACH (containing DCCH/BCCH/CCCH) and a FACH (containing DTCH). Or alternatively (when standalone PCH is mapped to an another S-CCPCH) carries: - a FACH (containing DCCH/BCCH/CCCH) and a FACH (containing DTCH). In both cases the spreading factor of this S-CCPCH is 64 (60 ksps) and proposed default value is 0 dB. The transmission power value is relative to the CPICH transmission power.
-35...15 dB, step 0.1 dB
DownlinkInnerLoopPCStepSize
The DL inner loop PC step size is used in normal mode by the WCDMA BTS to calculate the power increase/decrease when receiving TPC commands.
0.5 dB (0), 1.0 dB (1), 1.5 dB (2), 2.0 dB (3)
The DRX cycle length used by UTRAN to count paging occasions for discontinuous reception./n(The duration of the DRX cycle is 2 <power> k frames, where 'k' is the used DRX cycle length coefficient for UTRAN.)
80 ms (3), 160 ms (4), 320 ms (5), 640 ms (6), 1280 ms (7), 2560 ms (8), 5120 ms (9)
The RRC CONNECTION REQUEST retransmission timer (MS timer)./nThis parameter is part of System Information Block 1.
100 ms (0), 200 ms (1), 400 ms (2), 600 ms (3), 800 ms (4), 1000 ms (5), 1200 ms (6), 1400 ms (7), 1600 ms (8), 1800 ms (9), 2000 ms (10), 3000 ms (11), 4000 ms (12), 6000 ms (13), 8000 ms (14)
RRC CONNECTION REQUEST retransmission counter (MS counter)./nThis parameter is part of System Information Block 1.
The timer for supervising successful establishment of a physical channel (MS timer used in idle mode).
1...15 s, step 1 s
This parameter defines the maximum number of 'in sync' indications received from L1 during the establishment of a physical channel (UE counter used in idle mode)./nThis parameter is part of System Information Block 1.
1 (0), 2 (1), 4 (2), 10 (3), 20 (4), 50 (5), 100 (6), 200 (7), 400 (8), 600 (9), 800 (10), 1000 (11)
InterFreqMeasRepInterval
This parameter determines the measurement reporting interval for periodical inter-frequency measurements.
0.5 s (2), 1 s (3), 2 s (4), 3 s (5), 4 s (6)
HHoEcNoTimeHysteresis
If the inter-frequency or inter-RAT (GSM) handover caused by low measured absolute CPICH Ec/No is enabled, the UE transmits an event 1F triggered measurement report to the RNC when the CPICH Ec/No measurement result of an active set cell becomes worse than the threshold HHoEcNoThreshold. The parameter HHoEcNoTimeHysteresis determines the time period during which the CPICH Ec/No of the active set cell must stay worse than the threshold HHoEcNoThreshold before the UE can trigger the reporting event 1F. When the measured CPICH Ec/No of all active set cells has become worse than the threshold in question, the RNC starts inter-frequency or inter-RAT (GSM) measurements in compressed mode for the purpose of hard handover.
0 ms (0), 10 ms (1), 20 ms (2), 40 ms (3), 60 ms (4), 80 ms (5), 100 ms (6), 120 ms (7), 160 ms (8), 200 ms (9), 240 ms (10), 320 ms (11), 640 ms (12), 1280 ms (13), 2560 ms (14), 5000 ms (15)
If the inter-frequency or inter-RAT (GSM) handover caused by low measured absolute CPICH Ec/No is enabled, the RNC starts the inter-frequency or GSM measurement in compressed mode when all active set cells have triggered the reporting event 1F for CPICH Ec/No. The RNC cancels the event 1F of an active set cell if the CPICH Ec/No measurement result of the active set cell becomes better than or equal to the threshold HHoEcNoCancel and the UE transmits the corresponding event 1E triggered Measurement Report to the RNC. The parameter HHoEcNoCancelTime determines the time period during which the CPICH Ec/No of the active set cell must stay better than the threshold HHoEcNoCancel before the UE can trigger the reporting event 1E. Note that once the RNC has started the inter-frequency or inter-RAT (GSM) measurement for the purpose of hard handover due to low measured absolute CPICH Ec/No, the RNC does not break off the ongoing measurement, even if one or more active set cells trigger the reporting event 1E for CPICH Ec/No.
0 ms (0), 10 ms (1), 20 ms (2), 40 ms (3), 60 ms (4), 80 ms (5), 100 ms (6), 120 ms (7), 160 ms (8), 200 ms (9), 240 ms (10), 320 ms (11), 640 ms (12), 1280 ms (13), 2560 ms (14), 5000 ms (15)
If the inter-frequency or inter-RAT (GSM) handover caused by low measured absolute CPICH Ec/No is enabled, the UE transmits an event 1F triggered measurement report to the RNC when the CPICH Ec/No measurement result of an active set cell becomes worse than or equal to an absolute CPICH Ec/No threshold. The parameter HHoEcNoThreshold determines the absolute CPICH Ec/No threshold which is used by the UE to trigger the reporting event 1F. When the measured CPICH Ec/No of all active set cells has become worse than or equal to the threshold in question, the RNC starts inter-frequency or inter-RAT (GSM) measurements in compressed mode for the purpose of hard handover.
If the inter-frequency or inter-RAT (GSM) handover caused by low measured absolute CPICH Ec/No is enabled, the RNC starts the inter-frequency or GSM measurement in compressed mode when all active set cells have triggered the reporting event 1F for CPICH Ec/No. The RNC cancels the event 1F of an active set cell if the CPICH Ec/No measurement result of the active set cell becomes better than or equal to the threshold HHoEcNoCancel and the UE transmits the corresponding event 1E triggered Measurement Report to the RNC. Note that once the RNC has started the inter-frequency or inter-RAT (GSM) measurement for the purpose of hard handover due to low measured absolute CPICH Ec/No, the RNC does not break off the ongoing measurement, even if one or more active set cells trigger the reporting event 1E for CPICH Ec/No.
If the inter-frequency or inter-RAT (GSM) handover caused by low measured absolute CPICH Ec/No is enabled, the UE transmits an event 1F triggered measurement report to the RNC when the CPICH Ec/No measurement result of an active set cell becomes worse than or equal to an absolute CPICH Ec/No threshold. The parameter HHoEcNoThreshold determines the absolute CPICH Ec/No threshold which is used by the UE to trigger the reporting event 1F. When the measured CPICH Ec/No of all active set cells has become worse than or equal to the threshold in question, the RNC starts inter-frequency or inter-RAT (GSM) measurements in compressed mode for the purpose of hard handover.
If the inter-frequency or inter-RAT (GSM) handover caused by low measured absolute CPICH Ec/No is enabled, the UE transmits an event 1F triggered measurement report to the RNC when the CPICH Ec/No measurement result of an active set cell becomes worse than or equal to an absolute CPICH Ec/No threshold. The parameter HHoEcNoThreshold determines the absolute CPICH Ec/No threshold which is used by the UE to trigger the reporting event 1F. When the measured CPICH Ec/No of all active set cells has become worse than or equal to the threshold in question, the RNC starts inter-frequency or inter-RAT (GSM) measurements in compressed mode for the purpose of hard handover.
If the inter-frequency or inter-RAT (GSM) handover caused by low measured absolute CPICH Ec/No is enabled, the RNC starts the inter-frequency or GSM measurement in compressed mode when all active set cells have triggered the reporting event 1F for CPICH Ec/No. The RNC cancels the event 1F of an active set cell if the CPICH Ec/No measurement result of the active set cell becomes better than or equal to the threshold HHoEcNoCancel and the UE transmits the corresponding event 1E triggered Measurement Report to the RNC. Note that once the RNC has started the inter-frequency or inter-RAT (GSM) measurement for the purpose of hard handover due to low measured absolute CPICH Ec/No, the RNC does not break off the ongoing measurement, even if one or more active set cells trigger the reporting event 1E for CPICH Ec/No.
If the inter-frequency or inter-RAT (GSM) handover caused by low measured absolute CPICH Ec/No is enabled, the RNC starts the inter-frequency or GSM measurement in compressed mode when all active set cells have triggered the reporting event 1F for CPICH Ec/No. The RNC cancels the event 1F of an active set cell if the CPICH Ec/No measurement result of the active set cell becomes better than or equal to the threshold HHoEcNoCancel and the UE transmits the corresponding event 1E triggered Measurement Report to the RNC. Note that once the RNC has started the inter-frequency or inter-RAT (GSM) measurement for the purpose of hard handover due to low measured absolute CPICH Ec/No, the RNC does not break off the ongoing measurement, even if one or more active set cells trigger the reporting event 1E for CPICH Ec/No.
If the inter-frequency or inter-RAT (GSM) handover caused by low measured CPICH RSCP is enabled, the UE transmits an event 1F triggered measurement report to the RNC when the CPICH RSCP measurement result of an active set cell becomes worse than or equal to an absolute CPICH RSCP threshold. The parameter HHoRscpThreshold determines the absolute CPICH RSCP threshold which is used by the UE to trigger the reporting event 1F. When the measured CPICH RSCP of all active set cells has become worse than or equal to the threshold in question, the RNC starts inter-frequency or inter-RAT (GSM) measurements in compressed mode for the purpose of hard handover.
If the inter-frequency or inter-RAT (GSM) handover caused by low measured absolute CPICH RSCP is enabled, the RNC starts the inter-frequency or GSM measurement in compressed mode when all active set cells have triggered the reporting event 1F for CPICH RSCP. The RNC cancels the event 1F of an active set cell, if the CPICH RSCP measurement result of the active set cell becomes better than or equal to the threshold HHoRscpCancel and the UE transmits the corresponding event 1E triggered measurement report to the RNC. Note, that once the RNC has started the inter-frequency or inter-RAT (GSM) measurement for the purpose of hard handover due to low measured absolute CPICH RSCP, the RNC does not break off the ongoing measurement, even if one or more active set cells trigger the reporting event 1E for CPICH RSCP.
If the inter-frequency or inter-RAT (GSM) handover caused by low measured CPICH RSCP is enabled, the UE transmits an event 1F triggered measurement report to the RNC when the CPICH RSCP measurement result of an active set cell becomes worse than or equal to an absolute CPICH RSCP threshold. The parameter HHoRscpThreshold determines the absolute CPICH RSCP threshold which is used by the UE to trigger the reporting event 1F. When the measured CPICH RSCP of all active set cells has become worse than or equal to the threshold in question, the RNC starts inter-frequency or inter-RAT (GSM) measurements in compressed mode for the purpose of hard handover.
If the inter-frequency or inter-RAT (GSM) handover caused by low measured CPICH RSCP is enabled, the UE transmits an event 1F triggered measurement report to the RNC when the CPICH RSCP measurement result of an active set cell becomes worse than or equal to an absolute CPICH RSCP threshold. The parameter HHoRscpThreshold determines the absolute CPICH RSCP threshold which is used by the UE to trigger the reporting event 1F. When the measured CPICH RSCP of all active set cells has become worse than or equal to the threshold in question, the RNC starts inter-frequency or inter-RAT (GSM) measurements in compressed mode for the purpose of hard handover.
document.xls 文档密级:
04/17/2023 华为机密,未经许可不得扩散 第50页,共66页
HHoRscpCancel -115~-25 -102dbm
HHoRscpCancel -115~-25 -102dbm
AdjiQoffset1 0 dB
AdjiQoffset2 0 dB
AdjiQqualMin -18 dB
AdjiQrxlevMin -115 dBm
640 ms
HHoEcNoCancelTime 640 ms
HHoEcNoThreshold -24~0 -12dbm
HHoEcNoCancel -24~0 -12dbm
HHoEcNoThreshold -24~0 -12dbm
HHoEcNoThreshold -24~0 -12dbm
HHoEcNoCancel -24~0 -9dbm
HHoEcNoCancel -24~0 -9dbm
HHoRscpThreshold -24~0 -9dbm
HHoRscpCancel -24~0 -9dbm
HHoRscpThreshold -115~-25 -105dbm
HHoRscpThreshold -115~-25 -105dbm
HHoRscpCancel -115~-25 -102dbm
HHoRscpCancel -115~-25 -102dbm
AdjgRxLevMinHO 8
AdjgRxLevMinHO 8
AdjgRxLevMinHO 8
AdditionWindow 4 dB
AdditionWindow 4 dB
AdditionWindow 4 dB
If the inter-frequency or inter-RAT (GSM) handover caused by low measured absolute CPICH RSCP is enabled, the RNC starts the inter-frequency or GSM measurement in compressed mode when all active set cells have triggered the reporting event 1F for CPICH RSCP. The RNC cancels the event 1F of an active set cell, if the CPICH RSCP measurement result of the active set cell becomes better than or equal to the threshold HHoRscpCancel and the UE transmits the corresponding event 1E triggered measurement report to the RNC. Note, that once the RNC has started the inter-frequency or inter-RAT (GSM) measurement for the purpose of hard handover due to low measured absolute CPICH RSCP, the RNC does not break off the ongoing measurement, even if one or more active set cells trigger the reporting event 1E for CPICH RSCP.
If the inter-frequency or inter-RAT (GSM) handover caused by low measured absolute CPICH RSCP is enabled, the RNC starts the inter-frequency or GSM measurement in compressed mode when all active set cells have triggered the reporting event 1F for CPICH RSCP. The RNC cancels the event 1F of an active set cell, if the CPICH RSCP measurement result of the active set cell becomes better than or equal to the threshold HHoRscpCancel and the UE transmits the corresponding event 1E triggered measurement report to the RNC. Note, that once the RNC has started the inter-frequency or inter-RAT (GSM) measurement for the purpose of hard handover due to low measured absolute CPICH RSCP, the RNC does not break off the ongoing measurement, even if one or more active set cells trigger the reporting event 1E for CPICH RSCP.
This parameter is used in the cell re-selection and ranking between WCDMA cells. The value of this parameter is subtracted from the measured CPICH RSCP of the neighbour cell before the UE compares the quality measure with the cell re-selection//ranking criteria./nThis parameter is part of System Information Block 11&12.
-50...50 dB, step 1 dB
This parameter is used in the cell re-selection and ranking between WCDMA cells. The value of this parameter is subtracted from the measured CPICH Ec//No of the neighbour cell before the UE compares the quality measure with the cell re-selection//ranking criteria./nThis parameter is part of System Information Block 11&12.
-50...50 dB, step 1 dBThe minimum required quality
level in the cell (Ec//No)./nThis parameter is part of System Information Block 3.
-24...0 dB, step 1 dB
Determines the minimum required RSSI level which the measurement result of the GSM neighbour cell must exceed before the cell re-selection becomes possible./nThis parameter is part of System Information Block 11&12.
-115...-25 dBm, step 2 dBm
HHoEcNoTimeHysteresis
If the inter-frequency or inter-RAT (GSM) handover caused by low measured absolute CPICH Ec/No is enabled, the UE transmits an event 1F triggered measurement report to the RNC when the CPICH Ec/No measurement result of an active set cell becomes worse than the threshold HHoEcNoThreshold. The parameter HHoEcNoTimeHysteresis determines the time period during which the CPICH Ec/No of the active set cell must stay worse than the threshold HHoEcNoThreshold before the UE can trigger the reporting event 1F. When the measured CPICH Ec/No of all active set cells has become worse than the threshold in question, the RNC starts inter-frequency or inter-RAT (GSM) measurements in compressed mode for the purpose of hard handover.
0 ms (0), 10 ms (1), 20 ms (2), 40 ms (3), 60 ms (4), 80 ms (5), 100 ms (6), 120 ms (7), 160 ms (8), 200 ms (9), 240 ms (10), 320 ms (11), 640 ms (12), 1280 ms (13), 2560 ms (14), 5000 ms (15)
If the inter-frequency or inter-RAT (GSM) handover caused by low measured absolute CPICH Ec/No is enabled, the RNC starts the inter-frequency or GSM measurement in compressed mode when all active set cells have triggered the reporting event 1F for CPICH Ec/No. The RNC cancels the event 1F of an active set cell if the CPICH Ec/No measurement result of the active set cell becomes better than or equal to the threshold HHoEcNoCancel and the UE transmits the corresponding event 1E triggered Measurement Report to the RNC. The parameter HHoEcNoCancelTime determines the time period during which the CPICH Ec/No of the active set cell must stay better than the threshold HHoEcNoCancel before the UE can trigger the reporting event 1E. Note that once the RNC has started the inter-frequency or inter-RAT (GSM) measurement for the purpose of hard handover due to low measured absolute CPICH Ec/No, the RNC does not break off the ongoing measurement, even if one or more active set cells trigger the reporting event 1E for CPICH Ec/No.
0 ms (0), 10 ms (1), 20 ms (2), 40 ms (3), 60 ms (4), 80 ms (5), 100 ms (6), 120 ms (7), 160 ms (8), 200 ms (9), 240 ms (10), 320 ms (11), 640 ms (12), 1280 ms (13), 2560 ms (14), 5000 ms (15)
If the inter-frequency or inter-RAT (GSM) handover caused by low measured absolute CPICH Ec/No is enabled, the UE transmits an event 1F triggered measurement report to the RNC when the CPICH Ec/No measurement result of an active set cell becomes worse than or equal to an absolute CPICH Ec/No threshold. The parameter HHoEcNoThreshold determines the absolute CPICH Ec/No threshold which is used by the UE to trigger the reporting event 1F. When the measured CPICH Ec/No of all active set cells has become worse than or equal to the threshold in question, the RNC starts inter-frequency or inter-RAT (GSM) measurements in compressed mode for the purpose of hard handover.
If the inter-frequency or inter-RAT (GSM) handover caused by low measured absolute CPICH Ec/No is enabled, the UE transmits an event 1F triggered measurement report to the RNC when the CPICH Ec/No measurement result of an active set cell becomes worse than or equal to an absolute CPICH Ec/No threshold. The parameter HHoEcNoThreshold determines the absolute CPICH Ec/No threshold which is used by the UE to trigger the reporting event 1F. When the measured CPICH Ec/No of all active set cells has become worse than or equal to the threshold in question, the RNC starts inter-frequency or inter-RAT (GSM) measurements in compressed mode for the purpose of hard handover.
If the inter-frequency or inter-RAT (GSM) handover caused by low measured absolute CPICH Ec/No is enabled, the UE transmits an event 1F triggered measurement report to the RNC when the CPICH Ec/No measurement result of an active set cell becomes worse than or equal to an absolute CPICH Ec/No threshold. The parameter HHoEcNoThreshold determines the absolute CPICH Ec/No threshold which is used by the UE to trigger the reporting event 1F. When the measured CPICH Ec/No of all active set cells has become worse than or equal to the threshold in question, the RNC starts inter-frequency or inter-RAT (GSM) measurements in compressed mode for the purpose of hard handover.
If the inter-frequency or inter-RAT (GSM) handover caused by low measured absolute CPICH Ec/No is enabled, the UE transmits an event 1F triggered measurement report to the RNC when the CPICH Ec/No measurement result of an active set cell becomes worse than or equal to an absolute CPICH Ec/No threshold. The parameter HHoEcNoThreshold determines the absolute CPICH Ec/No threshold which is used by the UE to trigger the reporting event 1F. When the measured CPICH Ec/No of all active set cells has become worse than or equal to the threshold in question, the RNC starts inter-frequency or inter-RAT (GSM) measurements in compressed mode for the purpose of hard handover.
If the inter-frequency or inter-RAT (GSM) handover caused by low measured absolute CPICH Ec/No is enabled, the RNC starts the inter-frequency or GSM measurement in compressed mode when all active set cells have triggered the reporting event 1F for CPICH Ec/No. The RNC cancels the event 1F of an active set cell if the CPICH Ec/No measurement result of the active set cell becomes better than or equal to the threshold HHoEcNoCancel and the UE transmits the corresponding event 1E triggered Measurement Report to the RNC. Note that once the RNC has started the inter-frequency or inter-RAT (GSM) measurement for the purpose of hard handover due to low measured absolute CPICH Ec/No, the RNC does not break off the ongoing measurement, even if one or more active set cells trigger the reporting event 1E for CPICH Ec/No.
If the inter-frequency or inter-RAT (GSM) handover caused by low measured absolute CPICH Ec/No is enabled, the RNC starts the inter-frequency or GSM measurement in compressed mode when all active set cells have triggered the reporting event 1F for CPICH Ec/No. The RNC cancels the event 1F of an active set cell if the CPICH Ec/No measurement result of the active set cell becomes better than or equal to the threshold HHoEcNoCancel and the UE transmits the corresponding event 1E triggered Measurement Report to the RNC. Note that once the RNC has started the inter-frequency or inter-RAT (GSM) measurement for the purpose of hard handover due to low measured absolute CPICH Ec/No, the RNC does not break off the ongoing measurement, even if one or more active set cells trigger the reporting event 1E for CPICH Ec/No.
If the inter-frequency or inter-RAT (GSM) handover caused by low measured absolute CPICH Ec/No is enabled, the RNC starts the inter-frequency or GSM measurement in compressed mode when all active set cells have triggered the reporting event 1F for CPICH Ec/No. The RNC cancels the event 1F of an active set cell if the CPICH Ec/No measurement result of the active set cell becomes better than or equal to the threshold HHoEcNoCancel and the UE transmits the corresponding event 1E triggered Measurement Report to the RNC. Note that once the RNC has started the inter-frequency or inter-RAT (GSM) measurement for the purpose of hard handover due to low measured absolute CPICH Ec/No, the RNC does not break off the ongoing measurement, even if one or more active set cells trigger the reporting event 1E for CPICH Ec/No.
If the inter-frequency or inter-RAT (GSM) handover caused by low measured absolute CPICH Ec/No is enabled, the RNC starts the inter-frequency or GSM measurement in compressed mode when all active set cells have triggered the reporting event 1F for CPICH Ec/No. The RNC cancels the event 1F of an active set cell if the CPICH Ec/No measurement result of the active set cell becomes better than or equal to the threshold HHoEcNoCancel and the UE transmits the corresponding event 1E triggered Measurement Report to the RNC. Note that once the RNC has started the inter-frequency or inter-RAT (GSM) measurement for the purpose of hard handover due to low measured absolute CPICH Ec/No, the RNC does not break off the ongoing measurement, even if one or more active set cells trigger the reporting event 1E for CPICH Ec/No.
If the inter-frequency or inter-RAT (GSM) handover caused by low measured CPICH RSCP is enabled, the UE transmits an event 1F triggered measurement report to the RNC when the CPICH RSCP measurement result of an active set cell becomes worse than or equal to an absolute CPICH RSCP threshold. The parameter HHoRscpThreshold determines the absolute CPICH RSCP threshold which is used by the UE to trigger the reporting event 1F. When the measured CPICH RSCP of all active set cells has become worse than or equal to the threshold in question, the RNC starts inter-frequency or inter-RAT (GSM) measurements in compressed mode for the purpose of hard handover.
If the inter-frequency or inter-RAT (GSM) handover caused by low measured CPICH RSCP is enabled, the UE transmits an event 1F triggered measurement report to the RNC when the CPICH RSCP measurement result of an active set cell becomes worse than or equal to an absolute CPICH RSCP threshold. The parameter HHoRscpThreshold determines the absolute CPICH RSCP threshold which is used by the UE to trigger the reporting event 1F. When the measured CPICH RSCP of all active set cells has become worse than or equal to the threshold in question, the RNC starts inter-frequency or inter-RAT (GSM) measurements in compressed mode for the purpose of hard handover.
If the inter-frequency or inter-RAT (GSM) handover caused by low measured absolute CPICH RSCP is enabled, the RNC starts the inter-frequency or GSM measurement in compressed mode when all active set cells have triggered the reporting event 1F for CPICH RSCP. The RNC cancels the event 1F of an active set cell, if the CPICH RSCP measurement result of the active set cell becomes better than or equal to the threshold HHoRscpCancel and the UE transmits the corresponding event 1E triggered measurement report to the RNC. Note, that once the RNC has started the inter-frequency or inter-RAT (GSM) measurement for the purpose of hard handover due to low measured absolute CPICH RSCP, the RNC does not break off the ongoing measurement, even if one or more active set cells trigger the reporting event 1E for CPICH RSCP.
If the inter-frequency or inter-RAT (GSM) handover caused by low measured absolute CPICH RSCP is enabled, the RNC starts the inter-frequency or GSM measurement in compressed mode when all active set cells have triggered the reporting event 1F for CPICH RSCP. The RNC cancels the event 1F of an active set cell, if the CPICH RSCP measurement result of the active set cell becomes better than or equal to the threshold HHoRscpCancel and the UE transmits the corresponding event 1E triggered measurement report to the RNC. Note, that once the RNC has started the inter-frequency or inter-RAT (GSM) measurement for the purpose of hard handover due to low measured absolute CPICH RSCP, the RNC does not break off the ongoing measurement, even if one or more active set cells trigger the reporting event 1E for CPICH RSCP.
This parameter determines the minimum required GSM RSSI level which the averaged RSSI value of the GSMneighbour cell must exceed before the coverage (or quality) reason handover to GSM is possible.
-110...-47 dBm, step 1 dBm
This parameter determines the minimum required GSM RSSI level which the averaged RSSI value of the GSMneighbour cell must exceed before the coverage (or quality) reason handover to GSM is possible.
-110...-47 dBm, step 1 dBm
This parameter determines the minimum required GSM RSSI level which the averaged RSSI value of the GSMneighbour cell must exceed before the coverage (or quality) reason handover to GSM is possible.
-110...-47 dBm, step 1 dBm
Addition Window determines the relative threshold (A_Win) used by the UE to calculate the reporting range of event 1A. The threshold is either relative to the CPICH Ec/No measurement result of the best active set cell (M_best), or to the sum of active set measurement results (M_sum), depending on the value of the parameter Active Set Weighting Coefficient (W). When the CPICH Ec/No measurement result of a monitored cell (M_new) enters the reporting range, the UE transmits a Measurement Report to the RNC in order to add the monitored cell into the active set: M_new >= W * M_sum + ( 1 - W )* M_best - A_Win This parameter is part of System Information Block 11/12.
0...14.5 dB, step 0.5 dB
Addition Window determines the relative threshold (A_Win) used by the UE to calculate the reporting range of event 1A. The threshold is either relative to the CPICH Ec/No measurement result of the best active set cell (M_best), or to the sum of active set measurement results (M_sum), depending on the value of the parameter Active Set Weighting Coefficient (W). When the CPICH Ec/No measurement result of a monitored cell (M_new) enters the reporting range, the UE transmits a Measurement Report to the RNC in order to add the monitored cell into the active set: M_new >= W * M_sum + ( 1 - W )* M_best - A_Win This parameter is part of System Information Block 11/12.
0...14.5 dB, step 0.5 dB
Addition Window determines the relative threshold (A_Win) used by the UE to calculate the reporting range of event 1A. The threshold is either relative to the CPICH Ec/No measurement result of the best active set cell (M_best), or to the sum of active set measurement results (M_sum), depending on the value of the parameter Active Set Weighting Coefficient (W). When the CPICH Ec/No measurement result of a monitored cell (M_new) enters the reporting range, the UE transmits a Measurement Report to the RNC in order to add the monitored cell into the active set: M_new >= W * M_sum + ( 1 - W )* M_best - A_Win This parameter is part of System Information Block 11/12.
0...14.5 dB, step 0.5 dB
document.xls 文档密级:
04/17/2023 华为机密,未经许可不得扩散 第51页,共66页
DropWindow 6 dB
DropWindow 6 dB
DropWindow 6 dB
0...2, step 0.1
AdditionTime 100 ms
DropTime 640 ms
AdjsDERR No (0), Yes (1) No
AdjsDERR No (0), Yes (1) No
AdjsQoffset1 0 dB
AdjsQoffset2 0 dB
PtxSCCPCH1 0 dB
PtxPrimaryCPICH 33 dBm
-25 dB
1...64, step 1 8
2 dB
2 dB
PtxPrimarySCH -3 dB
RACH_Tx_NB01min 0...50, step 1 0
RACH_Tx_NB01max 0...50, step 1 50
RACH_tx_Max 1...32, step 1 8
PtxSecSCH -3 dB
CNDomainVersion -
AdjiQoffset1 0 dB
Drop Window determines the relative threshold (D_Win) which is used by the UE to calculate the reporting range of event 1B. The threshold is either relative to the CPICH Ec/No measurement result of the best active set cell (M_best) or to the sum of active set measurement results (M_sum), depending on the value of the parameter Active Set Weighting Coefficient (W). When the CPICH Ec/No measurement result of an active set cell (M_old) leaves the reporting range, the UE transmits a Measurement Report to the RNC in order to remove the cell from the active set: M_old <= W * M_sum + ( 1 - W )* M_best - D_Win This parameter is part of System Information Block 11/12.
0...14.5 dB, step 0.5 dB
Drop Window determines the relative threshold (D_Win) which is used by the UE to calculate the reporting range of event 1B. The threshold is either relative to the CPICH Ec/No measurement result of the best active set cell (M_best) or to the sum of active set measurement results (M_sum), depending on the value of the parameter Active Set Weighting Coefficient (W). When the CPICH Ec/No measurement result of an active set cell (M_old) leaves the reporting range, the UE transmits a Measurement Report to the RNC in order to remove the cell from the active set: M_old <= W * M_sum + ( 1 - W )* M_best - D_Win This parameter is part of System Information Block 11/12.
0...14.5 dB, step 0.5 dB
Drop Window determines the relative threshold (D_Win) which is used by the UE to calculate the reporting range of event 1B. The threshold is either relative to the CPICH Ec/No measurement result of the best active set cell (M_best) or to the sum of active set measurement results (M_sum), depending on the value of the parameter Active Set Weighting Coefficient (W). When the CPICH Ec/No measurement result of an active set cell (M_old) leaves the reporting range, the UE transmits a Measurement Report to the RNC in order to remove the cell from the active set: M_old <= W * M_sum + ( 1 - W )* M_best - D_Win This parameter is part of System Information Block 11/12.
0...14.5 dB, step 0.5 dB
ActiveSetWeightingCoefficient
Active Set Weighting Coefficient (W) is used to weight either the measurement result of the best active set cell (M_best) or the sum of measurement results of all active set cells (M_sum) when the UE calculates the reporting range for the events 1A (cell addition) and 1B (dropping of cell). The formula is: W * M_sum + ( 1 - W )* M_best This parameter is part of System Information Block 11/12.
managedObject class="WCEL"中包含RtFmcsIdentifier的值对应到managedObject class="FMCS" version="×××" distName="PLMN-PLMN/RNC-××/FMCS-××模版中的ActiveSetWeightingCoefficient值。
When a monitored cell enters the reporting range (addition window), the cell must continuously stay within the reporting range for a given period of time before the UE can send a Measurement Report to the RNC in order to add the cell into the active set (event 1A). The length of this period is controlled by the parameter Addition Time. This parameter is part of System Information Block 11/12.
0 ms (0), 10 ms (1), 20 ms (2), 40 ms (3), 60 ms (4), 80 ms (5), 100 ms (6), 120 ms (7), 160 ms (8), 200 ms (9), 240 ms (10), 320 ms (11), 640 ms (12), 1280 ms (13), 2560 ms (14), 5000 ms (15)
When an active set cell leaves the reporting range (drop window), the cell must continuously stay outside the reporting range for a given period of time before the UE can send a Measurement Report to the RNC in order to remove the cell from the active set (event 1B). The length of this period is controlled by the parameter Drop Time. This parameter is part of System Information Block 11/12.
0 ms (0), 10 ms (1), 20 ms (2), 40 ms (3), 60 ms (4), 80 ms (5), 100 ms (6), 120 ms (7), 160 ms (8), 200 ms (9), 240 ms (10), 320 ms (11), 640 ms (12), 1280 ms (13), 2560 ms (14), 5000 ms (15)
This parameter indicates whether the neighbouring cell is forbidden to affect the reporting range (addition/drop window) calculation, if it belongs to the active set.
This parameter indicates whether the neighbouring cell is forbidden to affect the reporting range (addition/drop window) calculation, if it belongs to the active set.
This parameter is used in the cell re-selection and ranking between WCDMA cells. The value of this parameter is subtracted from the measured CPICH RSCP of the neighbour cell before the UE compares the quality measure with the cell re-selection//ranking criteria./nThis parameter is part of System Information Block 11&12.
-50...50 dB, step 1 dB
This parameter is used in the cell re-selection and ranking between WCDMA cells. The value of this parameter is subtracted from the measured CPICH Ec//No of the neighbour cell before the UE compares the quality measure with the cell re-selection//ranking criteria./nThis parameter is part of System Information Block 11&12.
-50...50 dB, step 1 dB
This is the transmission power of the S-CCPCH channel, which carries: - a PCH (containing PCCH), a FACH (containing DCCH/BCCH/CCCH) and a FACH (containing DTCH). Or alternatively (when standalone PCH is mapped to an another S-CCPCH) carries: - a FACH (containing DCCH/BCCH/CCCH) and a FACH (containing DTCH). In both cases the spreading factor of this S-CCPCH is 64 (60 ksps) and proposed default value is 0 dB. The transmission power value is relative to the CPICH transmission power.
-35...15 dB, step 0.1 dB
This is the transmission power of the primary common pilot channel. The P-CPICH physical channel carries the common pilots of the cell, which is defined in the cell setup. The transmission power of the CPICH physical channel defines the actual cell size, which means that the power is determined by radio network planning. This parameter is used, for example, for neighbour measurements - critical for the network performance. The default value is 5-10% of the maximum transmitting power of WCDMA BTS, which can be, for example, 43 dBm/carrier. Note: Changing the parameter value will start the cell shutdown procedure in the BTS. Note: The cell is blocked if the WCDMA BTS does not support the used value. Typical supported range is (Cell max power - 18dB)..(Cell max power - 3dB). This parameter is part of System Information Block 5.
-10...50 dBm, step 0.1 dBm
PRACHRequiredReceivedCI
This UL required received C/I value is used by the UE to calculate the initial output power on PRACH according to the Open loop power control procedure. This parameter defines the value of the IE Constant value, which is part of System Information Block 5. The value of the parameter depends on the propagation channel. Note: If the operator perceives a difference in DL and UL linklosses, for example when MHA is used in BTS, then this parameter can be used to compensate for it in the power of the first transmitted preamble on the PRACH.
-35...-10 dB, step 1 dB
PRACH_preamble_retrans
The maximum number of preambles allowed in one preamble ramping cycle. PRACH Preamble Retrans Max is part of "PRACH power offset" which is part of "PRACH system information list" which is part of System Information Block 5&6.
PowerRampStepPRACHpreamble
The power ramp step on PRACH preamble when no acquisition indicator (AI) is detected by the UE. This parameter is part of System Information Block 5.
1...8 dB, step 1 dB
PowerOffsetLastPreamblePRACHmessage
The power offset between the last transmitted preamble and the control part of the PRACH message (added to the preamble power to receive the power of the message control part). This parameter is part of System Information Block 5.
-5...10 dB, step 1 dB
This is the transmission power of the primary synchronisation channel. The power level is relative to the [FDD-primary CPICH power]. The primary SCH consists of a modulated code 256 chips in length: the Primary Synchronisation Code (PSC) transmitted once every slot. The PSC is the same for every cell in the system, and it enables the downlink slot synchronisation in the cell. Note: Changing the parameter value will start the cell shutdown procedure in the BTS.
-35...15 dB, step 0.1 dB
In case that a negative acknowledgement has been received by UE on AICH a backoff timer TBO1 is started to determine when the next RACH transmission attempt will be started. The backoff timer TBO1 is set to an integer number NBO1 of 10 ms time intervals, randomly drawn within an interval 0 <= NB01min <= NBO1 <= NB01max (with uniform distribution). After TB01 has been expired, the next RACH attempt will be started. NB01min and NB01max may be set equal when a fixed delay is desired, and even to zero when no delay other than the one due to persistency is desired. NB01min is given as an integer between 0 and 50 which gives the Lower bound of the waiting time in 10ms steps. NB01min is part of "RACH transmission parameters" which is part of "PRACH system information list" which is part of System Information Block 5&6.
In case that a negative acknowledgement has been received by UE on AICH a backoff timer TBO1 is started to determine when the next RACH transmission attempt will be started. The backoff timer TBO1 is set to an integer number NBO1 of 10 ms time intervals, randomly drawn within an interval 0 <= NB01min <= NBO1 <= NB01max (with uniform distribution). After TB01 has been expired, the next RACH attempt will be started. NB01min and NB01max may be set equal when a fixed delay is desired, and even to zero when no delay other than the one due to persistency is desired. NB01max is given as an integer between 0 and 50 which gives the Upper bound of the waiting time in 10ms steps. NB01max is part of "RACH transmission parameters" which is part of "PRACH system information list" which is part of SIB5/6. This parameter is part of System Information Block 5.
Maximum number of RACH preamble cycles defines how many times the PRACH pre-amble ramping procedure can be repeated before UE MAC reports a failure on RACH transmission to higher layers. Maximum number of RACH preamble cycles is part of "RACH transmission parameters" which is part of "PRACH system information list" which is part of SIB5/6. This parameter is part of System Information Block 5.
This is the transmission power of the secondary synchronisation channel related to the Primary CPICH transmission power. The secondary SCH consists of repeatedly transmitting a length 15 sequence of modulated codes 256 chips in length. These are the Secondary Synchronisation Codes (SSC), transmitted in parallel with the primary SCH. This sequence on the secondary SCH enables the downlink frame synchronisation, and indicates, to which code group the cell downlink scrambling code belongs. Each SSC is chosen from a set of 16 different codes 256 chips in length. Note: Changing the parameter value will start the cell shutdown procedure in the BTS.
-35...15 dB, step 0.1 dB
The code that uniquely identifies the Release version of the Core Network connected to the RNC.
R99 (1), Rel4 (2), Rel5 (3), Rel6 (4)
This parameter is used in the cell re-selection and ranking between WCDMA cells. The value of this parameter is subtracted from the measured CPICH RSCP of the neighbour cell before the UE compares the quality measure with the cell re-selection//ranking criteria./nThis parameter is part of System Information Block 11&12.
-50...50 dB, step 1 dB
document.xls 文档密级:
04/17/2023 华为机密,未经许可不得扩散 第52页,共66页
AdjsQoffset2 0 dB
0.5 s
0.5 s
ReplacementWindow 2 dB
ReplacementTime 100 ms
MaxActiveSetSize 2...3, step 1 3
AdjsQoffset1 0 dB
AdjsQoffset2 0 dB
Sintrasearch 10db
Sintersearch 8 dB
0.5 s
0.5 s
ReplacementWindow 2 dB
0...2, step 0.1 0
CellBarred Not barred
Allowed
Tbarred 40 s
ToCellFACHinTest No (0), Yes (1) Yes (1)
ToCellFACHinTest No (0), Yes (1) Yes (1)
This parameter is used in the cell re-selection and ranking between WCDMA cells. The value of this parameter is subtracted from the measured CPICH Ec//No of the neighbour cell before the UE compares the quality measure with the cell re-selection//ranking criteria./nThis parameter is part of System Information Block 11&12.
-50...50 dB, step 1 dB
AdditionReportingInterval
When a monitored cell enters the reporting range and triggers event 1A (cell addition), the UE transmits a Measurement Report to the RNC. If the RNC is not able to add the monitored cell to the active set, the UE continues reporting after the initial report by reverting to periodical measurement reporting. The parameter Addition Reporting Interval determines the interval between periodical measurement reports when such reporting is triggered by the event 1A. This parameter is part of System Information Block 11/12.
gui ==> internalNo periodical reporting ==> 00.25 s. Not allowed ==> 10.5 s ==> 21 s ==> 32 s ==> 44 s ==> 58 s ==> 616 s ==> 7
ReplacementReportingInterval
When the number of cells in the active set has reached the maximum, and a monitored cell becomes better than an active set cell, the UE transmits a When the number of cells in the active set has reachedthe maximum, and a monitored cell becomes betterthan an active set cell, the UE transmits a MeasurementReport to the RNC in order to replace the active cellwith the monitored cell (event 1C). If the RNC is notable to replace the active cell with the monitored cell,the UE continues reporting after the initial report byreverting to periodical measurement reporting. Theparameter Replacement Reporting Interval determinesthe interval of periodical measurement reports whensuch reporting is triggered by the event 1C.
gui ==> internalNo periodical reporting ==> 00.25 s. Not allowed ==> 10.5 s ==> 21 s ==> 32 s ==> 44 s ==> 58 s ==> 616 s ==> 7
When the number of cells in the active set has reached the maximum specified by the parameter MaxActiveSetSize and a monitored cell becomes better than an active set cell, the UE transmits a Measurement Report to the RNC in order to replace the active cell with the monitored cell (event 1C). The parameter Replacement Window determines the margin by which the CPICH Ec/No measurement result of the monitored cell (MNew) must exceed the CPICH Ec/No measurement result of the an active set cell (MInAS) before the UE can send the event 1C triggered Measurement Report to the RNC: MNew >= MInAs + ReplacementWindow / 2 This parameter is part of System Information Block 11/12.
0...7.5 dB, step 0.5 dB
When the number of cells in the active set has reachedthe maximum, and a monitored cell enters the reportingrange (replacement window), the monitored cell mustcontinuously stay within the reporting range for a givenperiod of time before the UE can send a MeasurementReport to the RNC in order to replace an active set cellwith the monitored cell (event 1C). The length of thisperiod is controlled by the parameter ReplacementTime.
gui ==> internal0 ms ==> 010 ms ==> 120 ms ==> 240 ms ==> 360 ms ==> 480 ms ==> 5100 ms ==> 6120 ms ==> 7160 ms ==> 8200 ms ==> 9240 ms ==> 10320 ms ==> 11640 ms ==> 121280 ms ==> 132560 ms ==> 145000 ms ==> 15
This parameter determines the maximum number of cells which can participate in a soft/softer handover. Reporting deactivation threshold indicates the maximum number of cells allowed in the active set in order for the event 1A to trigger. The RNC calculates the deactivation threshold from the parameter MaxActiveSetSize: Reporting Deactivation Threshold = MaxActiveSetSize - 1 Reporting Deactivation Threshold parameter is part of System Information Block 11/12. Replacement activation threshold information element indicates the minimum number of cells allowed in the active set in order for the event 1C to trigger. The threshold equals to the maximum size of the active set which is controlled with the parameter MaxActiveSetSize. Replacement Activation Threshold parameter is part of System Information Block 11/12.
This parameter is used in the cell re-selection and ranking between WCDMA cells. The value of this parameter is subtracted from the measured CPICH RSCP of the neighbour cell before the UE compares the quality measure with the cell re-selection//ranking criteria./nThis parameter is part of System Information Block 11&12.
-50...50 dB, step 1 dB
This parameter is used in the cell re-selection and ranking between WCDMA cells. The value of this parameter is subtracted from the measured CPICH Ec//No of the neighbour cell before the UE compares the quality measure with the cell re-selection//ranking criteria./nThis parameter is part of System Information Block 11&12.
-50...50 dB, step 1 dB
The threshold for intra-frequency measurements, and for the HCS measurement rules./nNote: If no threshold is given, MS performs measurements./nThis parameter is part of System Information Block 3.
0...20 dB, step 2 dB
The threshold for inter-frequency measurements, and for the HCS measurement rules. /nNote: If no threshold is given, MS performs measurements./nThis parameter is part of System Information Block 3.
0...20 dB, step 2 dB
AdditionReportingInterval
When a monitored cell enters the reporting range and triggers event 1A (cell addition), the UE transmits a Measurement Report to the RNC. If the RNC is not able to add the monitored cell to the active set, the UE continues reporting after the initial report by reverting to periodical measurement reporting. The parameter Addition Reporting Interval determines the interval between periodical measurement reports when such reporting is triggered by the event 1A. This parameter is part of System Information Block 11/12.
gui ==> internalNo periodical reporting ==> 00.25 s. Not allowed ==> 10.5 s ==> 21 s ==> 32 s ==> 44 s ==> 58 s ==> 616 s ==> 7
ReplacementReportingInterval
When the number of cells in the active set has reached the maximum, and a monitored cell becomes better than an active set cell, the UE transmits a When the number of cells in the active set has reachedthe maximum, and a monitored cell becomes betterthan an active set cell, the UE transmits a MeasurementReport to the RNC in order to replace the active cellwith the monitored cell (event 1C). If the RNC is notable to replace the active cell with the monitored cell,the UE continues reporting after the initial report byreverting to periodical measurement reporting. Theparameter Replacement Reporting Interval determinesthe interval of periodical measurement reports whensuch reporting is triggered by the event 1C.
gui ==> internalNo periodical reporting ==> 00.25 s. Not allowed ==> 10.5 s ==> 21 s ==> 32 s ==> 44 s ==> 58 s ==> 616 s ==> 7
When the number of cells in the active set has reached the maximum specified by the parameter MaxActiveSetSize and a monitored cell becomes better than an active set cell, the UE transmits a Measurement Report to the RNC in order to replace the active cell with the monitored cell (event 1C). The parameter Replacement Window determines the margin by which the CPICH Ec/No measurement result of the monitored cell (MNew) must exceed the CPICH Ec/No measurement result of the an active set cell (MInAS) before the UE can send the event 1C triggered Measurement Report to the RNC: MNew >= MInAs + ReplacementWindow / 2 This parameter is part of System Information Block 11/12.
0...7.5 dB, step 0.5 dB
ActiveSetWeightingCoefficient
Active Set Weighting Coefficient (W) is used to weight either the measurement result of the best active set cell (M_best) or the sum of measurement results of all active set cells (M_sum) when the UE calculates the reporting range for the events 1A (cell addition) and 1B (dropping of cell). The formula is: W * M_sum + ( 1 - W )* M_best This parameter is part of System Information Block 11/12.
When the number of cells in the active set has reached the maximum, and a monitored cell enters the reporting range (replacement window), the monitored cell must continuously stay within the reporting range for a given period of time before the UE can send a Measurement Report to the RNC in order to replace an active set cell with the monitored cell (event 1C). The length of this period is controlled by the parameter Replacement Time. This parameter is part of System Information Block 11/12.
Defines whether the cell is barred or not./nA barred cell is a cell where a UE is not allowed to camp on. Emergency calls shall be allowed in all cells whose barred status is 'not barred'. When cell status is 'barred', the UE is not permitted to select//re-select the cell, not even for emergency calls./nThis parameter is part of System Information Block 3.
Barred (0), Not barred (1)
IntraFreq_Cell_Reselect_Ind
Defines whether intra-frequency cell re-selection is allowed or not when the cell is barred./nWhen a cell's status is 'barred', the UE is not permitted to select//re-select this cell, except in some cases for an emergency call. If the 'Intra-frequency cell re-selection indicator' is set to value 'allowed', the UE may select another cell on the same frequency if selection//re-selection criteria are fulfilled. If the 'Intra-frequency cell re-selection indicator' is set to 'not allowed' the UE shall not re-select even a different cell on the same frequency as the barred cell. For emergency call, the Intra-frequency cell re-selection indicator IE' shall be ignored. 'Intra-frequency cell re-selection indicator' is part of SIB3//4 in the case the 'cell barred' indicator is true./nThis parameter is part of System Information Block 3.
Allowed (0), Not allowed (1)
When the cell is barred, the UE must check between the time interval ‘Cell barred period’, whether the status of the barred cell has changed./nThis parameter is part of the System Information Block 3.
10 s (0), 20 s (1), 40 s (2), 80 s (3), 160 s (4), 320 s (5), 640 s (6), 1280 s (7)
When the test timer expires, the UE is switched to Cell_FACH state when the value of the parameter ToCellFACHinTest is 'Yes'. If the ToCellFACHinTest parameter value is 'No', an Iu Release procedure is initiated in the Cell_DCH state, and the UE is switched directly to idle mode.0 (No), 1 (Yes)
When the test timer expires, the UE is switched to Cell_FACH state when the value of the parameter ToCellFACHinTest is 'Yes'. If the ToCellFACHinTest parameter value is 'No', an Iu Release procedure is initiated in the Cell_DCH state, and the UE is switched directly to idle mode.0 (No), 1 (Yes)
document.xls 文档密级:
04/17/2023 华为机密,未经许可不得扩散 第53页,共66页
ToCellFACHinTest No (0), Yes (1) Yes (1)
2000 ms
MSActivitySupervision 29 minutes
0(0ms)
30 min
3s
3s
When the test timer expires, the UE is switched to Cell_FACH state when the value of the parameter ToCellFACHinTest is 'Yes'. If the ToCellFACHinTest parameter value is 'No', an Iu Release procedure is initiated in the Cell_DCH state, and the UE is switched directly to idle mode.0 (No), 1 (Yes)
InactivityTimerDownlinkDCH128InactivityTimerDownlinkDCH16InactivityTimerDownlinkDCH256InactivityTimerDownlinkDCH32InactivityTimerDownlinkDCH320InactivityTimerDownlinkDCH384InactivityTimerDownlinkDCH64InactivityTimerDownlinkDCH8InactivityTimerUplinkDCH128InactivityTimerUplinkDCH16InactivityTimerUplinkDCH256InactivityTimerUplinkDCH32InactivityTimerUplinkDCH320InactivityTimerUplinkDCH384InactivityTimerUplinkDCH64SignallingLinkInactivityTimerCellDCHtestTmrMACdflowthroughputTimetoTriggerEDCHMACdFlowThroughputTimetoTrigger
The time indicating how long the radio and transmission resources are reserved after silence detection on downlink DCH before release procedures. Default values: 8 kbps: 5 s 16 kbps: 5 s 32 kbps: 5 s 64 kbps: 3 s 128 kbps: 2 s 256 kbps: 2 s 320 kbps: 2 s 384 kbps: 2 s
0...20 s, step 1 s
UL_DL_activation_timer
This timer is used on MAC -c to detect idle periods on data transmission (NRT RBs and SRBs) for the UE, which is in Cell_FACH state. Based on this timer the MAC -c shall give the No_Data indication to the RRC, which further can change the state of the RRC from Cell_FACH state to the Cell_PCH state (or URA_PCH state).
50...10000 ms, step 50 ms
This timer is used in RRC states Cell_PCH and URA_PCH for supervising the inactivity of NRT RAB(s).If the parameter value is set to zero, state transition to Cell_PCH / URA_PCH state is not allowed. When inactivity is detected in Cell_FACH state, the UE will be switched to the idle mode. Range and step: 0 ... 1440 min, step 1 min
0...1440 minutes, step 1 minutesTrafVolThresholdULLo
wTrafVolThresholdDLLowNASsignVolThrULNASsignVolThrDL
This parameter defines, in bytes, the threshold of data in the RLC buffers of SRB0, SRB1, SRB2, SRB3, SRB4 and all NRT RBs that triggers the uplink traffic volume measurement report, when the UE is in Cell_FACH state. Otherwise, UE sends data on RACH.This parameter is sent to the UE using an RRC:MEASUREMENT CONTROL message.
gui ==> internal8 bytes ==> 816 bytes ==> 1632 bytes ==> 3264 bytes ==> 64128 bytes ==> 128256 bytes ==> 256512 bytes ==> 5121 KB ==> 1024
TrafVolTimeToTriggerULTrafVolTimeToTriggerDL
This parameter defines, in ms, the period of time between the timing of event detection and the timing ofsending a traffic volume measurement report.This parameter is sent to the UE using an RRC: MEASUREMENT CONTROL message.
gui ==> internal0 ms ==> 010 ms ==> 1020 ms ==> 2040 ms ==> 4060 ms ==> 6080 ms ==> 80100 ms ==> 100120 ms ==> 120160 ms ==> 160200 ms ==> 200240 ms ==> 240320 ms ==> 320640 ms ==> 6401280 ms ==> 12802560 ms ==> 25605000 ms ==> 5000
CellReselectionObservingTime
The timer is set when the first Cell Update message due to 'cell reselection' is received while UE is in CELL_FACH or CELL_PCH state. In expiry of the timer, the counter MaxCellReselections is reset. Below is an example of target RRC state selection when value 3 is used for MaxCellReselections: Velocity Cell radius Cell Update Target RRC state km/h km frequency 50 10 12 minutes CELL_PCH 50 20 24 minutes CELL_PCH 75 10 8 minutes URA_PCH 75 20 16 minutes CELL_PCH 100 10 6 minutes URA_PCH 100 20 12 minutes CELL_PCH
1...60 min, step 1 minEDCHMACdFlowThro
ughputAveWinMACdflowthroughputAveWin
This parameter defines the size of the sliding averaging window for the throughput measurement of the E-DCH NRT MAC-d flow. The throughput measurement measures the number of bits transmitted by the E-DCH MAC-d flow during the sliding measurement window.The value 0 of the parameter means that the E-DCH MAC-d flow throughput measurement is not performed.
0.5...10 s, step 0.5 sinternal_value = gui_value * 2
EDCHMACdFlowThroughputAveWinMACdflowthroughputAveWin
This parameter defines the size of the sliding averaging window for the throughput measurement of the E-DCH NRT MAC-d flow. The throughput measurement measures the number of bits transmitted by the E-DCH MAC-d flow during the sliding measurement window.The value 0 of the parameter means that the E-DCH MAC-d flow throughput measurement is not performed.
0.5...10 s, step 0.5 sinternal_value = gui_value * 2
document.xls 文档密级:
04/17/2023 华为机密,未经许可不得扩散 第54页,共66页
Tcell -
PriScrCode 0...511, step 1 -
LAC -
SAC - -
RAC 0...255, step 1 -
Cid -
UARFCN -
Qhyst1PCH 0...40,step 1 -
Qhyst1FACH 0...40,step 1 -
Qhyst2PCH 0...40,step 1 -
Qhyst2FACH 0...40,step 1 -
TreselectionFACH 0...6.2,step 0.2 -
TreselectionPCH 0...31,step 1 -
GsmMeasRepInterval 0.5 s (2), 1 s (3), -
GsmMeasAveWindow 1...32 -
GsmMinHoInterval 1..60 -
MaxNbrOfHSSCCHCod 1...3 -
GsmHandoverAMR
GsmHandoverNrtPS No (0), Yes (1)
PrxMaxTargetBTS 0...30 6 dB
MaxNumberEDCHCell 1...20 72
[-8.2..+17.3] 4dB
[-8.2..+17.3] 6dB
[-8.2..+17.3] 13dB
Each cell in a BTS uses a System Frame Number (SFN) counter, which is the BTS Frame Number (BFN) counter delayed by a number of chips defined by the value of Tcell. Tcell is used for defining the start of SCH, CPICH, Primary CCPCH and DL Scrambling Code(s) in a cell relative to BFN. The main purpose is to avoid having overlapping SCHs in different cells belonging to the same BTS. An SCH burst is 256 chips long. The values can be chosen as follows: 0 chips for the 1st cell of the BTS, 256 chips for the 2nd cell of the BTS, 512 chips for the 3rd cell of the BTS, etc. Note: Changing the parameter value will start the cell shutdown procedure in the BTS.
0 chips (0), 256 chips (1), 512 chips (2), 768 chips (3), 1024 chips (4), 1280 chips (5), 1536 chips (6), 1792 chips (7), 2048 chips (8), 2304 chips (9)
Identifies the downlink scrambling code of the Primary CPICH (Common Pilot Channel) of the Cell. Note: Changing the parameter value will start the cell shutdown procedure in the BTS. This parameter is part of System Information Block 11.
This parameter contains the Location area code (LAC) of a WCDMA cell. The coding of the Location area code (two octets) is the responsibility of administration. LAI (Location Area Identification) consists of PLMNid and LAC. If LAI has to be deleted, LAC is set as 0xFFFE. This parameter is also part of System Information Block 1 and known as IE: GSM-MAP NAS system information.
1...65535, step 1
The Service Area Identifier (SAI) identifies an area consisting of one or more cells which belong to the same Location Area (LAI). The Service Area Identifier is composed of the PLMN Identifier, the Location Area Code (LAC) and the Service Area Code (SAC).
The routing area code determines the Routing area within the location area to which the cell belongs to. It is used only for PS services (part of PS domain specific NAS system information in SIB1). Routing area identification (RAI) consists of LAI and RAC, LAI consists of PLMNid and LAC. This parameter is part of System Information Block 1.
The parameter identifies the cell within a RNC. This parameter is part of System Information Block 3.
1...65535, step 1
The carrier frequency is designated by the parameter UTRA Absolute Radio Frequency Channel Number (UARFCN). This parameter defines the downlink channel number. The uplink channel number is calculated by the RNC based on a duplex distance used in the RF band. The relation between UARFCN (Nd) and the corresponding carrier frequency (Fdownlink [MHz]) in RF bands I, II and V is defined with the following equations: Fdownlink = 0.2 * Nd MHz Nd = 5 * Fdownlink The relation between the UARFCN (Nd) additional channel and the corresponding carrier frequency (Fdownlink [MHz]) in RF band II is defined with the following equations: Fdownlink = (1850.1 + 0.2 * Nd) MHz Nd = 5 * (Fdownlink - 1850.1 MHz) The relation between the UARFCN (Nd) additional channel and the corresponding carrier frequency (Fdownlink [MHz]) in RF band V is defined with the following equations: Fdownlink = (670.1 + 0.2 * Nd) MHz Nd = 5 * (Fdownlink - 670.1 MHz) Downlink RF band I is 2110 - 2170 MHz. Downlink RF band II is 1930 - 1990 MHz. Downlink RF band V is 869 - 894 MHz. Allowed channel numbers (Nd) in RF band I are: 10562 - 10838. Allowed channel numbers (Nd) in RF band II are: 9663 - 9712, 9763 - 9812, 9888 - 9937. Allowed additional channel numbers (Nd) in RF band II are: 412, 437, 462, 487, 512, 537, 562, 587, 612, 637, 662, 687. Allowed channel numbers (Nd) in RF band V are: 4357 - 4458. Allowed additional channel numbers (Nd) in RF band V are: 1007, 1012, 1032, 1037, 1062, 1087. The duplex distance is 190 MHz in RF band I, 80 MHz in RF band II and 45 MHz in RF band V. This parameter is part of System Information Block 5.
0...16383, step 1
The parameter is used for cell selection and reselectionin Cell_PCH/URA_PCH.Qhyst1PCH is used for TDD and GSM cells, and forFDD cells when cell selection and re-selectionquality measure is set to CPICH RSCP.This is hysteresis between WCDMA and GSMcells. Hysteresis is not needed because negativeoffset is used.
The parameter is used for cell selection and reselectionin Cell_FACH.The parameter is used for TDD and GSM cells, andfor FDD cells when cell selection and re-selectionquality measure is set to CPICH RSCP.This is hysteresis between WCDMA and GSMcells. Hysteresis is not needed because negativeoffset is used.
The parameter is used for cell selection and reselectionin Cell_PCH/URA_PCH.The parameter is used for FDD cells when cellselection and re-selection quality measure is set toCPICH Ec/No.2dB hysteresis between WCDMA cells can be usedin urban environment to avoid ping-pong.0dB hysteresis can be used in areas of high mobilitylike highways.
The parameter is used for FDD cells when cellselection and re-selection The parameter is usedfor cell selection and re-selection in Cell_FACH.The parameter is used for FDD cells when cellselection and re-selection quality measure is set toCPICH Ec/No.2dB hysteresis between WCDMA cells can be usedin urban environment to avoid ping-pong. 0dB hysteresiscan be used in areas of high mobility likehighways.
This parameter is used for cell selection and reselectionin Cell_FACH.The UE triggers the reselection of a new cell if thecell reselection criteria are fulfilled during the timeinterval TreselectionFACH.The reselection time of 2s may avoid too many cellreselections between cells and hence LA/RAupdates when crossing the LA/RA border. Thus,there are less signalling and less call failures at theLA/RA border due to the LA/RA update. The reselectiontime of 0s can be used in areas of highmobility, such as highways.
selectionin Cell_PCH/URA_PCH.The UE triggers the reselection of a new cell if thecell reselection criteria are fulfilled during the timeinterval TreselectionPCH.The reselection time of 2s may avoid too many cellreselections between cells and hence LA/RAupdates when crossing the LA/RA border. Thus,there are less signalling and less call failures at theLA/RA border due to the LA/RA update. The reselectiontime of 0s can be used in areas of highmobility, such as highways.
This parameter determines the measurementreporting interval for periodical inter-RAT (GSM)measurements.
This parameter determines the maximum numberof periodical inter-RAT (GSM) measurementreports (maximum size of the sliding averagingwindow) from which the RNC calculates theaveraged GSM RSSI values for the handoverdecision algorithm.
This parameter determines the minimum intervalbetween a successful inter-RAT handover fromGSM to UTRAN and the following inter-RAThandover attempt back to GSM related to the sameRRC connection.
This parameter defines the maximum number ofHS-SCCH codes (SF 128) that can be reserved inone cell.More than one HS-SCCH code can be used if theHSDPA code multiplexing functionality is in use.The actual number of reserved codes depends onfor example HSDPA capabilities and HSDPA codemultiplexing support (RNC and BTS).
This parameter indicates whether an inter-RAThandover to GSM is allowed for circuit switched(CS) voice services. The alternative values of theparameter are the following:- No; handover to GSM is not allowed for CS voiceservices. The handover is also prohibited if a CSvoice service is a part of multiservice.- Yes; handover to GSM is allowed for CS voice services.In case of multiservice, a handover to GSMmust be allowed for all CS and PS services whichparticipate in the multiservice before the handoveris possible.- Priority; handover to GSM is allowed for CS voiceservices. The handover is also allowed if a CS voiceservice is a part of multiservice.
No (0), Yes (1), Priority (2)
This parameter indicates whether an inter-RAThandover (cell change) to GSM/GPRS is allowedfor non-real time packet switched (PS) dataservices in CELL_DCH state of connected mode.The alternative values of the parameter are the following:- No; cell change to GSM/GPRS is not allowed fornon-real time PS data services. The handover/cellchange to GSM/GPRS is also prohibited if a nonrealtime PS data service is a part of multiservice.- Yes; cell change to GSM/GPRS is allowed fornon-real time PS data services. In case of multiservice,a handover/cell change to GSM/GPRS mustbe allowed for all CS and PS services which participatein the multiservice before the handover/cellchange is possible.The parameters GsmHandoverAMR and/orGsmHandoverCS for CS data/voice services canoverrule the value of the parameter GsmHandoverNrtPSin case of multiservice. If either CSvoice and/or data services are prioritized, the RNCshall execute the handover to GSM even if the cellchange to GSM/GPRS is not allowed for non-realtime PS data services.
HHoRscpFilterCoefficient
In the CELL_DCH state the UE physical layer measurementperiod for intra-frequency CPICH RSCPmeasurements is 200 ms. The Filter Coefficientparameter controls the higher layer filtering ofphysical layer CPICH RSCP measurements beforethe event evaluation and measurement reporting isperformed by the UE. The CPICH RSCP measurementreports can be used to trigger off inter-frequencyor inter-RAT (GSM) measurements for thepurpose of hard handover.The higher layer filtering is described in 3GPP TS25.331 RRC Protocol Specification, section FilterCoefficient.
Filtering period of 200 ms (0), Filtering periodapproximates 300 ms (1), Filtering period approximates400 ms (2), Filtering period approximates600 ms (3), Filtering period approximates 800 ms(4), Filtering period approximates 1100 ms (5), Filteringperiod approximates 1600 ms (6)
The maximum target for received total wide band
power in the cell for BTS packet schedulingThis parameter determines the
maximum numberof E-DCH allocations in the cell.INITSIRTARGET(2-
antenna and MinSF=2SF4)
initial Uplink SIR Target for RABs
NITSIRTARGET(2-antenna and
MinSF<2SF4)
initial Uplink SIR Target for RABs
MAXSIRTARGET(2-antenna and
MinSF=2SF4)
Max Uplink SIR Target for RABs
document.xls 文档密级:
04/17/2023 华为机密,未经许可不得扩散 第55页,共66页
[-8.2..+17.3] 15dB
MINSIRTARGET Min Uplink SIR Target for RABs [-8.2..+17.3] 0
low to 16% 1%
low to 16% 1%
CQI Feedback Cycle 4ms
MAXSIRTARGET(2-antenna and
MinSF<2SF4)
Max Uplink SIR Target for RABs
BLER targets for E-DCH 10ms
BLER targets for E-DCH 2ms
is determining the CQI report transmissions on the HS-
DPCCH
document.xls 文档密级:
04/17/2023 华为机密,未经许可不得扩散 第56页,共66页
NSN
RU20
Mapping Rule Remark
Use the NSN value.
Use the NSN value.
Use the NSN value.
Use the Huawei baseline value.
Use the Huawei baseline value.
Use the Huawei baseline value.
Use the Huawei baseline value.
Use the NSN value.
Locate the NSN value in the following order:WCEL > the last ADJG > the HopgIdentifier value > the HOPG value > the AdjgQrxlevMin value
NSN does not have such a parameter.NSN does not have such a parameter.NSN does not have such a parameter.NSN does not have such a parameter.
Huawei NSN RESERVED reserved NOT_RESERVED Not reserved Huawei NSN NOT_BARRED 0 BARRED 1 Huawei NSN NOT_BARRED 0 BARRED 1 Huawei NSN NOT_BARRED 0 BARRED 1 Huawei NSN NOT_BARRED 0 BARRED 1 Huawei NSN NOT_BARRED 0 BARRED 1 Huawei NSN NOT_BARRED 0 BARRED 1 Huawei NSN NOT_BARRED 0 BARRED 1 Huawei NSN NOT_BARRED 0 BARRED 1 Huawei NSN NOT_BARRED 0 BARRED 1 Huawei NSN NOT_BARRED 0 BARRED 1 Huawei NSN NOT_BARRED 0 BARRED 1 Huawei NSN NOT_BARRED 0 BARRED 1 Huawei NSN NOT_BARRED 0 BARRED 1 Huawei NSN NOT_BARRED 0 BARRED 1 Huawei NSN NOT_BARRED 0 BARRED 1 Huawei NSN NOT_BARRED 0 BARRED 1
document.xls 文档密级:
04/17/2023 华为机密,未经许可不得扩散 第57页,共66页
Use the Huawei baseline value.
Use the Huawei baseline value.
Huawei NSN NOT_BARRED Not barred BARRED barred Huawei NSN ALLOWED Allowed NOT_ALLOWED Not allowed Huawei NSN DN Ns
Huawei NSNMaxTxPower+HspaPower<==>PtxMaxHSDPA
Locate the NSN value in the following order:WCEL > the RtFmciIdentifier value > the FMCI value > the InterFreqMeasRepInterval value Huawei NSN D500 0.5 s D1000 1 s ……………………….. D(N*1000) N s
Use the value 0.
Use the value 0.
Locate the NSN value in the following order:WCEL > the RtFmcsIdentifier value > the FMCS value > the HHoEcNoTimeHysteresis value Huawei NSN D0 0 ms D10 10 ms ……………………… D(N) N ms
Locate the NSN value in the following order:WCEL > the RtFmcsIdentifier value > the FMCS value > the HHoEcNoCancelTime valueIf the NSN value is larger than the Huawei value, use the NSN value. Otherwise, use the Huawei baseline value. Huawei NSN D0 0 ms D10 10 ms ……………………… D(N) N ms
Locate the NSN value in the following order:WCEL > the RtFmcsIdentifier value > the FMCS value > the HHoEcNoThreshold value
Locate the NSN value in the following order:WCEL > the RtFmcsIdentifier value > the FMCS value > the HHoEcNoCancel value
Locate the NSN value in the following order:WCEL > the NrtFmcsIdentifier value > the FMCS value > the HHoEcNoThreshold value
Locate the NSN value in the following order:WCEL > the NrtFmcsIdentifier value > the FMCS value > the HHoEcNoThreshold value
Locate the NSN value in the following order:WCEL > the NrtFmcsIdentifier value > the FMCS value > the HHoEcNoCancel value
Locate the NSN value in the following order:WCEL > the NrtFmcsIdentifier value > the FMCS value > the HHoEcNoCancel value
Locate the NSN value in the following order:WCEL > the RtFmcsIdentifier value > the FMCS value > the HHoRscpThreshold value
Locate the NSN value in the following order:WCEL > the RtFmcsIdentifier value > the FMCS value > the HHoRscpCancel value
Locate the NSN value in the following order:WCEL > the NrtFmcsIdentifier value > the FMCS value > the HHoRscpThreshol value
Locate the NSN value in the following order:WCEL > the NrtFmcsIdentifier value > the FMCS value > the HHoRscpThreshol value
Locate the NSN value in the following order:WCEL > the NrtFmcsIdentifier value > the FMCS value > the HHoRscpCancel value
Locate the NSN value in the following order:WCEL > the NrtFmcsIdentifier value > the FMCS value > the HHoRscpCancel valueUse the value 0.
Use the value 0.
Locate the NSN value in the following order:WCEL > the RtFmcsIdentifier value > the FMCS value > the HHoEcNoTimeHysteresis value Huawei NSN D0 0 ms D10 10 ms ……………………… D(N) N ms
Locate the NSN value in the following order:WCEL > the RtFmcsIdentifier value > the FMCS value > the HHoEcNoCancelTime valueIf the NSN value is larger than the Huawei value, use the NSN value. Otherwise, use the Huawei baseline value. Huawei NSN D0 0 ms D10 10 ms ……………………… D(N) N ms
NSN does not have such a parameter.
Locate the NSN value in the following order:WCEL > the RtFmcsIdentifier value > the FMCS value > the GSMcauseCPICHEcNo valueIf the NSN value is Disabled, use the value -24. Otherwise, locate another NSN value in the following order:WCEL > the RtFmcsIdentifier value > the FMCS value > the HHoEcNoThreshold value
document.xls 文档密级:
04/17/2023 华为机密,未经许可不得扩散 第58页,共66页
Use the Huawei baseline value.
Use the Huawei baseline value.
Use the Huawei baseline value.
Locate the NSN value in the following order:WCEL > the RtFmcsIdentifier value > the FMCS value > the GSMcauseCPICHEcNo valueIf the NSN value is Disabled, use the value -22. Otherwise, locate another NSN value in the following order:WCEL > the RtFmcsIdentifier value > the FMCS value > the HHoEcNoCancel value
Locate the NSN value in the following order:WCEL > the NrtFmcsIdentifier value > the FMCS value > the GSMcauseCPICHEcNo valueIf the NSN value is Disabled, use the value -24. Otherwise, locate another NSN value in the following order:WCEL > the NrtFmcsIdentifier value > the FMCS value > the HHoEcNoThreshold value
Locate the NSN value in the following order:WCEL > the NrtFmcsIdentifier value > the FMCS value > the GSMcauseCPICHEcNo valueIf the NSN value is Disabled, use the value -24. Otherwise, locate another NSN value in the following order:WCEL > the NrtFmcsIdentifier value > the FMCS value > the HHoEcNoThreshold value
Locate the NSN value in the following order:WCEL > the NrtFmcsIdentifier value > the FMCS value > the GSMcauseCPICHEcNo valueIf the NSN value is Disabled, use the value -22. Otherwise, locate another NSN value in the following order:WCEL > the NrtFmcsIdentifier value > the FMCS value > the HHoEcNoCancel value
Locate the NSN value in the following order:WCEL > the NrtFmcsIdentifier value > the FMCS value > the GSMcauseCPICHEcNo valueIf the NSN value is Disabled, use the value -22. Otherwise, locate another NSN value in the following order:WCEL > the NrtFmcsIdentifier value > the FMCS value > the HHoEcNoCancel value
Locate the NSN value in the following order:WCEL > the RtFmcsIdentifier value > the FMCS value > the GSMcauseCPICHrscp valueIf the NSN value is Disabled, use the value -115. Otherwise, locate another NSN value in the following order:WCEL > the RtFmcsIdentifier value > the FMCS value > the HHoRscpThreshold value
Locate the NSN value in the following order:WCEL > the RtFmcsIdentifier value > the FMCS value > the GSMcauseCPICHrscp valueIf the NSN value is Disabled, use the value -113. Otherwise, locate another NSN value in the following order:WCEL > the RtFmcsIdentifier value > the FMCS value > the HHoRscpCancel value
Locate the NSN value in the following order:WCEL > the NrtFmcsIdentifier value > the FMCS value > the GSMcauseCPICHrscp valueIf the NSN value is Disabled, use the value -115. Otherwise, locate another NSN value in the following order:WCEL > the NrtFmcsIdentifier value > the FMCS value > the HHoRscpThreshold value
Locate the NSN value in the following order:WCEL > the NrtFmcsIdentifier value > the FMCS value > the GSMcauseCPICHrscp valueIf the NSN value is Disabled, use the value -115. Otherwise, locate another NSN value in the following order:WCEL > the NrtFmcsIdentifier value > the FMCS value > the HHoRscpThreshold value
Locate the NSN value in the following order:WCEL > the NrtFmcsIdentifier value > the FMCS value > the GSMcauseCPICHrscp valueIf the NSN value is Disabled, use the value -113. Otherwise, locate another NSN value in the following order:WCEL > the NrtFmcsIdentifier value > the FMCS value > the HHoRscpCancel value
Locate the NSN value in the following order:WCEL > the NrtFmcsIdentifier value > the FMCS value > the GSMcauseCPICHrscp valueIf the NSN value is Disabled, use the value -113. Otherwise, locate another NSN value in the following order:WCEL > the NrtFmcsIdentifier value > the FMCS value > the HHoRscpCancel value
Locate the NSN value in the following order:WCEL > the last ADJG > the RtHopgIdentifier value > the HOPG value > the AdjgRxLevMinHO value
Locate the NSN value in the following order:WCEL > the last ADJG > the NRtHopgIdentifier value > the HOPG value > the AdjgRxLevMinHO value
Locate the NSN value in the following order:WCEL > the last ADJG > the NRtHopgIdentifier value > the HOPG value > the AdjgRxLevMinHO value
Locate the NSN value in the following order:WCEL > the RtFmcsIdentifier value > the FMCS value > the AdditionWindow value
Locate the NSN value in the following order:WCEL > the RtFmcsIdentifier value > the FMCS value > the AdditionWindow value
Locate the NSN value in the following order:WCEL > the NrtFmcsIdentifier value > the FMCS value > the AdditionWindow value
Locate the NSN value in the following order:WCEL > the RtFmcsIdentifier value > the FMCS value > the DropWindow value
Locate the NSN value in the following order:WCEL > the RtFmcsIdentifier value > the FMCS value > the DropWindow value
Locate the NSN value in the following order:WCEL > the NrtFmcsIdentifier value > the FMCS value > the DropWindow value NSN does not have
such a parameter.NSN does not have such a parameter.NSN does not have such a parameter.
Locate the NSN value in the following order:WCEL > the RtFmcsIdentifier value > the FMCS value > the AdditionTime value Huawei NSN D0 0 ms D10 10 ms ……………………… D(N) N ms
Locate the NSN value in the following order:WCEL > the RtFmcsIdentifier value > the FMCS value > the DropTime value Huawei NSN D0 0 ms D10 10 ms ……………………… D(N) N ms
document.xls 文档密级:
04/17/2023 华为机密,未经许可不得扩散 第59页,共66页
Use the Huawei baseline value.
Use the NSN value.
Use the NSN value.
Use the Huawei baseline value.
Use the NSN value.
Use the Huawei baseline value.
Use the NSN value.
Use the NSN value.
Use the NSN value.
Use the NSN value.
Use the NSN value.
Use the NSN value.
Use the NSN value.
Use the NSN value.
Use the NSN value.
Use the NSN value.
Use the Huawei baseline value.
NSN does not have such a parameter.The NSN value is 3 as well.
Huawei NSN ALLOWED IMSI attach/detach allowed NOT_ALLOWED IMSI attach/detach not allowed
HUAWEI NSNMODE1 Network Mode of Operation I MODE2 Network Mode of Operation II
Huawei NSN 3 80 ms 4 160 ms 5 320 ms 6 640 ms 7 1280 ms 8 2560 ms 9 5120 ms
Huawei NSN D1000 1000 ms D1200 1200 ms…………………………….. D(N) N ms
If the NSN value is larger than the Huawei baseline value, use the NSN value. Otherwise, use the Huawei baseline value.If the NSN value is larger than the Huawei baseline value, use the NSN value. Otherwise, use the Huawei baseline value.
Huawei NSN D1 0 D2 1 D4 2 D10 3 D20 4 D50 5 D100 6 D200 7 D400 8 D600 9 D800 10 D1000 11
If the NSN value is larger than the Huawei baseline value, use the NSN value. Otherwise, use the Huawei baseline value.
Huawei NSN D50 N<=5 D100 6 D200 7 The value D12 is recommended.The value D30 is recommended.
Huawei NSN D1 0 D50 1 D100 2 D200 3 D400 4 D600 5 D800 6 D1000 7 D2 8 D4 9 D10 10 D20 11
document.xls 文档密级:
04/17/2023 华为机密,未经许可不得扩散 第60页,共66页
Use the Huawei baseline value.
Use the Huawei baseline value.
Use the Huawei baseline value.
Use the Huawei baseline value.
Use the Huawei baseline value.
Use the Huawei baseline value.
Use the Huawei baseline value.
Use the NSN value.
Use the Huawei baseline value.
Use the Huawei baseline value.
Use the Huawei baseline value.
Use the Huawei baseline value.
Use the Huawei baseline value.
Use the Huawei baseline value.
Use the Huawei baseline value.
Use the Huawei baseline value.
Use the Huawei baseline value.
Use the Huawei baseline value.
Use the Huawei baseline value.
Use the Huawei baseline value.
Use the Huawei baseline value.
NSN does not have such a parameter.
NSN does not have such a parameter.
NSN does not have such a parameter.If the NSN value is larger than
the Huawei baseline value, use the NSN value. Otherwise, use the Huawei baseline value. Huawei NSN 3 80 ms 4 160 ms 5 320 ms 6 640 ms 7 1280 ms 8 2560 ms 9 5120 ms
Huawei NSN DN 100ms<=N<=2000ms D2000 N>2000msIf the NSN value is larger than the Huawei baseline value, use the NSN value. Otherwise, use the Huawei baseline value.
Huawei NSN D1 0 D2 1 D4 2 D10 3 D20 4 D50 5 D100 6 D200 7 D400 8 D600 9 D800 10 D1000 11
Use the value 0.
Use the value 0.
document.xls 文档密级:
04/17/2023 华为机密,未经许可不得扩散 第61页,共66页
Use the Huawei baseline value.
Use the Huawei baseline value.
Use the Huawei baseline value.
Use the Huawei baseline value.
Use the Huawei baseline value.
Use the Huawei baseline value.
Use the Huawei baseline value.
Use the Huawei baseline value.
Use the Huawei baseline value.
Use the Huawei baseline value.
Use the Huawei baseline value.
Use the Huawei baseline value.
Use the Huawei baseline value.
Use the Huawei baseline value.
Use the Huawei baseline value.
Use the Huawei baseline value.
Use the Huawei baseline value.
Use the Huawei baseline value.
Use the Huawei baseline value.
Use the Huawei baseline value.
Use the Huawei baseline value.
Use the Huawei baseline value.
Use the Huawei baseline value.
NSN does not have such a parameter.
Locate the NSN value in the following order:WCEL > ADJI > the RtHopgIdentifier value > the HOPI value > the AdjiQoffset1 value
Locate the NSN value in the following order:WCEL > ADJI > the RtHopgIdentifier value > the HOPI value > the AdjiQoffset2 value
Locate the NSN value in the following order:WCEL > ADJI > the RtHopgIdentifier value > the HOPI value > the AdjiQqualMin value
Locate the NSN value in the following order:WCEL > ADJI > the RtHopgIdentifier value > the HOPI value > the AdjiQrxlevMin valueUse the value 0.
Use the value 0.
document.xls 文档密级:
04/17/2023 华为机密,未经许可不得扩散 第62页,共66页
Use the Huawei baseline value.
Use the Huawei baseline value.
Use the Huawei baseline value.
Use the Huawei baseline value.
Use the Huawei baseline value.
Use the Huawei baseline value.
Use the Huawei baseline value.
Use the Huawei baseline value.
Use the Huawei baseline value.
Use the Huawei baseline value.
Use the Huawei baseline value.
Use the NSN value.
Use the NSN value.
Use the NSN value.
Use the NSN value.
Use the NSN value.
Use the Huawei baseline value.
Use the NSN value.
Use the NSN value.
Use the NSN value.
Use the NSN value.
Use the NSN value.
Use the Huawei baseline value.
Use the Huawei baseline value.
Use the Huawei baseline value.
NSN does not have such a parameter.NSN does not have such a parameter.NSN does not have such a parameter.
NSN does not have such a parameter.NSN does not have such a parameter.
Huawei NSNNOT_AFFECT NO AFFECT YES Huawei NSNNOT_AFFECT NO AFFECT YES
Locate the NSN value in the following order:WCEL > ADJS > the RtHopsIdentifier value > the HOPS value > the AdjsQoffset1 value
Locate the NSN value in the following order:WCEL > ADJS > the RtHopsIdentifier value > the HOPS value > the AdjsQoffset2 value
NSN does not have such a parameter.
For connected-state-related parameters, Huawei baseline values are recommended but the multi-carrier policy must be considered as well when Huawei baseline values are used.
document.xls 文档密级:
04/17/2023 华为机密,未经许可不得扩散 第63页,共66页
Use the Huawei baseline value.
Use the Huawei baseline value.
Use the Huawei baseline value.
Use the Huawei baseline value.
Use the Huawei baseline value.
Use the Huawei baseline value.
Use the Huawei baseline value.
Use the Huawei baseline value.
Use the Huawei baseline value.
Use the Huawei baseline value.
Use the Huawei baseline value.
Use the Huawei baseline value.
Use the Huawei baseline value.
Use the Huawei baseline value.
Use the Huawei baseline value.
Use the Huawei baseline value.
Use the Huawei baseline value.
Use the Huawei baseline value.
Use the Huawei baseline value.
Use the Huawei baseline value.
Use the Huawei baseline value.
Use the Huawei baseline value.
Use the Huawei baseline value.
Use the Huawei baseline value.
Use the Huawei baseline value.
Use the Huawei baseline value.
Use the Huawei baseline value.
For connected-state-related parameters, Huawei baseline values are recommended but the multi-carrier policy must be considered as well when Huawei baseline values are used.
NSN does not have such a parameter.NSN does not have such a parameter.NSN does not have such a parameter.
Because the NSN value is smaller than the Huawei value, triggering event 1A or 1C is relatively difficult for Huawei. For event 1A or 1C, the Huawei buffering mechanism is different from the NSN buffering mechanism. If the NSN value is used, the number of times event 1A or 1C is reported will increase, leading to the increased call drop rate.
NSN does not have such a parameter.
Because the NSN value is smaller than the Huawei value, triggering event 1A or 1C is relatively difficult for Huawei. For event 1A or 1C, the Huawei buffering mechanism is different from the NSN buffering mechanism. If the NSN value is used, the number of times event 1A or 1C is reported will increase, leading to the increased call drop rate.
Because the NSN value is smaller than the Huawei value, triggering event 1A or 1C is relatively difficult for Huawei. For event 1A or 1C, the Huawei buffering mechanism is different from the NSN buffering mechanism. If the NSN value is used, the number of times event 1A or 1C is reported will increase, leading to the increased call drop rate.
Because the NSN value is smaller than the Huawei value, triggering event 1A or 1C is relatively difficult for Huawei. For event 1A or 1C, the Huawei buffering mechanism is different from the NSN buffering mechanism. If the NSN value is used, the number of times event 1A or 1C is reported will increase, leading to the increased call drop rate.
The NSN value is 3 as well.
For connected-state-related parameters, Huawei baseline values are recommended but the multi-carrier policy must be considered as well when Huawei baseline values are used.
For connected-state-related parameters, Huawei baseline values are recommended but the multi-carrier policy must be considered as well when Huawei baseline values are used.
For connected-state-related parameters, Huawei baseline values are recommended but the multi-carrier policy must be considered as well when Huawei baseline values are used.
For connected-state-related parameters, Huawei baseline values are recommended but the multi-carrier policy must be considered as well when Huawei baseline values are used.
NSN does not have such a parameter.Use the Huawei baseline
value.Use the Huawei baseline value.
NSN does not have such a parameter.NSN does not have such a parameter.
Because the NSN value is smaller than the Huawei value, triggering event 1A or 1C is relatively difficult for Huawei. For event 1A or 1C, the Huawei buffering mechanism is different from the NSN buffering mechanism. If the NSN value is used, the number of times event 1A or 1C is reported will increase, leading to the increased call drop rate.
NSN does not have such a parameter.
Because the NSN value is smaller than the Huawei value, triggering event 1A or 1C is relatively difficult for Huawei. For event 1A or 1C, the Huawei buffering mechanism is different from the NSN buffering mechanism. If the NSN value is used, the number of times event 1A or 1C is reported will increase, leading to the increased call drop rate.
Because the NSN value is smaller than the Huawei value, triggering event 1A or 1C is relatively difficult for Huawei. For event 1A or 1C, the Huawei buffering mechanism is different from the NSN buffering mechanism. If the NSN value is used, the number of times event 1A or 1C is reported will increase, leading to the increased call drop rate.
NSN value is 0 as well.
Because the NSN value is smaller than the Huawei value, triggering event 1A or 1C is relatively difficult for Huawei. For event 1A or 1C, the Huawei buffering mechanism is different from the NSN buffering mechanism. If the NSN value is used, the number of times event 1A or 1C is reported will increase, leading to the increased call drop rate.
For connected-state-related parameters, Huawei baseline values are recommended but the multi-carrier policy must be considered as well when Huawei baseline values are used.
For connected-state-related parameters, Huawei baseline values are recommended but the multi-carrier policy must be considered as well when Huawei baseline values are used.
For connected-state-related parameters, Huawei baseline values are recommended but the multi-carrier policy must be considered as well when Huawei baseline values are used.
For state transition, the NSN mechanism is different from the Huawei mechanism. The NSN mechanism imposes restrictions on the user plane and control plane. However, the Huawei baseline value is recommended.
For state transition, the NSN mechanism is different from the Huawei mechanism. The NSN mechanism imposes restrictions on the user plane and control plane. However, the Huawei baseline value is recommended.
document.xls 文档密级:
04/17/2023 华为机密,未经许可不得扩散 第64页,共66页
Use the Huawei baseline value.
Use the Huawei baseline value.
Use the Huawei baseline value.
Use the Huawei baseline value.
Use the Huawei baseline value.
Use the Huawei baseline value.
Use the Huawei baseline value.
Use the Huawei baseline value.
Use the Huawei baseline value.
Use the Huawei baseline value.
Use the Huawei baseline value.
Use the Huawei baseline value.
Use the Huawei baseline value.
Use the Huawei baseline value.
Use the Huawei baseline value.
Use the Huawei baseline value.
Use the Huawei baseline value.
Use the Huawei baseline value.
Use the Huawei baseline value.
Use the Huawei baseline value.
Use the Huawei baseline value.
InterFreqCSThd2DEcN0 + 3
InterFreqCSThd2DRSCP + 3
For state transition, the NSN mechanism is different from the Huawei mechanism. The NSN mechanism imposes restrictions on the user plane and control plane. However, the Huawei baseline value is recommended.
For state transition, the NSN mechanism is different from the Huawei mechanism. The NSN mechanism imposes restrictions on the user plane and control plane. However, the Huawei baseline value is recommended.
For state transition, the NSN mechanism is different from the Huawei mechanism. The NSN mechanism imposes restrictions on the user plane and control plane. However, the Huawei baseline value is recommended.
For state transition, the NSN mechanism is different from the Huawei mechanism. The NSN mechanism imposes restrictions on the user plane and control plane. However, the Huawei baseline value is recommended.
For state transition, the NSN mechanism is different from the Huawei mechanism. The NSN mechanism imposes restrictions on the user plane and control plane. However, the Huawei baseline value is recommended.
For state transition, the NSN mechanism is different from the Huawei mechanism. The NSN mechanism imposes restrictions on the user plane and control plane. However, the Huawei baseline value is recommended.
For state transition, the NSN mechanism is different from the Huawei mechanism. The NSN mechanism imposes restrictions on the user plane and control plane. However, the Huawei baseline value is recommended.
For state transition, the NSN mechanism is different from the Huawei mechanism. The NSN mechanism imposes restrictions on the user plane and control plane. However, the Huawei baseline value is recommended.
For state transition, the NSN mechanism is different from the Huawei mechanism. The NSN mechanism imposes restrictions on the user plane and control plane. However, the Huawei baseline value is recommended.
For state transition, the NSN mechanism is different from the Huawei mechanism. The NSN mechanism imposes restrictions on the user plane and control plane. However, the Huawei baseline value is recommended.
For state transition, the NSN mechanism is different from the Huawei mechanism. The NSN mechanism imposes restrictions on the user plane and control plane. However, the Huawei baseline value is recommended.
For state transition, the NSN mechanism is different from the Huawei mechanism. The NSN mechanism imposes restrictions on the user plane and control plane. However, the Huawei baseline value is recommended.
For state transition, the NSN mechanism is different from the Huawei mechanism. The NSN mechanism imposes restrictions on the user plane and control plane. However, the Huawei baseline value is recommended.
NSN does not have such a parameter.
InterFreqR99PsThd2DEcN0 + 3
NSN does not have such a parameter.
InterFreqR99PsThd2DEcN0 + 3
NSN does not have such a parameter.NSN does not have such a parameter.
InterFreqR99PsThd2DRSCP + 3
NSN does not have such a parameter.
InterFreqR99PsThd2DRSCP + 3
NSN does not have such a parameter.
document.xls 文档密级:
04/17/2023 华为机密,未经许可不得扩散 第65页,共66页
Use the NSN value.
Use the NSN value.
Use the NSN value.
Use the NSN value.
Use the NSN value.
Use the NSN value.
Use the NSN value.
Use the NSN value.
Use the NSN value.
Use the NSN value.
Use the NSN value.
Use the NSN value.
Use the NSN value.
Use the NSN value.
Use the Huawei baseline value.
Use the Huawei baseline value.
Use the Huawei baseline value.
Use the Huawei baseline value.
Use the Huawei baseline value.
Use the Huawei baseline value.
Huawei NSNCHIP0 0chipsCHIP256 256chipsCHIP512 512chipsCHIP768 768chipsCHIP1024 1024 chipsCHIP1280 1280chipsCHIP1536 1536chipsCHIP1792 1792chipsCHIP2048 2048chipsCHIP2304 2304chips
Before using the NSN value, turn on the SIB4 switch by running the following command:MOD UCELLSIBSWITCH: CellId=***, SibCfgBitMap=SIB4-1;
Before using the NSN value, turn on the SIB4 switch by running the following command:MOD UCELLSIBSWITCH: CellId=***, SibCfgBitMap=SIB4-1;
Before using the NSN value, turn on the SIB4 switch by running the following command:MOD UCELLSIBSWITCH: CellId=***, SibCfgBitMap=SIB4-1;
Before using the NSN value, turn on the SIB4 switch by running the following command:MOD UCELLSIBSWITCH: CellId=***, SibCfgBitMap=SIB4-1;
Before using the NSN value, turn on the SIB4 switch by running the following command:MOD UCELLSIBSWITCH: CellId=***, SibCfgBitMap=SIB4-1;
Before using the NSN value, turn on the SIB4 switch by running the following command:MOD UCELLSIBSWITCH: CellId=***, SibCfgBitMap=SIB4-1;
HUAWEI NSN D500 0.5SD1000 1SD2000 2SD3000 3SD4000 4SHUAWEI<==>GsmMeasAveWindow*GsmMeasRepInterval
HUAWEI NSN HO_INTER_RAT_CS_OUT_SWITCH-0 NOHUAWEI NSN HO_INTER_RAT_PS_OUT_SWITCH-0 NO
HUAWEI NSN0 Filtering period approximates 200 ms
Use Huawei suggestion:122(4dB)
May be further Optimized to
103(2.1dB). Need validation
in several networks.
Use Huawei suggestion:182(10dB)
document.xls 文档密级:
04/17/2023 华为机密,未经许可不得扩散 第66页,共66页
Use the Huawei baseline value.
Use the Huawei baseline value.
Use the Huawei baseline value.
Use the Huawei baseline value.
Use the NSN value.
Use Huawei suggestion(4dB)REFETFCIIDX1=4, REFETFCIIDX2=54, REFETFCIPO1=PO_24/15,
REFETFCIPO2=PO_106/15,Use Huawei suggestion: ERGCH2INDSTPTHS=16, ERGCH3INDSTPTHS=13