PRODUCT CHANGE NOTIFICATION No 6.1 07/01-2014 MEC A/S www.mec.dk Page 1/7 We hereby inform you that PCBs for illuminated and non-illuminated Navimec and Controlmec modules have been changed. All versions have been integrated into one PCB that can be adjusted according to the required design. The integraon of the various PCBs was decided upon to ease stock handling. The new PCB has two connectors: upper one (J1) for switches and lower one (J2) for chip-LEDs to illumi- nate controlmec (see page 3 for circuit diagram and connector informaon). As the second connector is used only for illuminated controlmec there are two part numbers for the PCB: 1. Part no. for PCB and connector for switches - 9810130 (illuminated and non-illuminated Navimec and non-illuminated controlmec) 2. Part no. for PCB and both connectors - 9810135 (illuminated controlmec) The LEDs on the module are either single colour LED (the same as used in 5 series switches - see specifi- caons in the catalogue p. 46) or RGB LEDs (19-237/R6GHBHC-A04/2T from Everlight Electronics CO. LTD - see specificaons on p.4-7 in this PCN). J1 J2 7,2 10 46,7 40 32 33 3,5 Ø3,2 (x4) 12,5 12,5 12,5 12,5 20
Transcript
PRODUCT CHANGE NOTIFICATION No 6.107/01-2014
MEC A/S www.mec.dk Page 1/7
We hereby inform you that PCBs for illuminated and non-illuminated Navimec and Controlmec modules have been changed. All versions have been integrated into one PCB that can be adjusted according to the required design.
The integration of the various PCBs was decided upon to ease stock handling.
The new PCB has two connectors: upper one (J1) for switches and lower one (J2) for chip-LEDs to illumi-nate controlmec (see page 3 for circuit diagram and connector information).
As the second connector is used only for illuminated controlmec there are two part numbers for the PCB:1. Part no. for PCB and connector for switches - 9810130 (illuminated and non-illuminated Navimec and non-illuminated controlmec)2. Part no. for PCB and both connectors - 9810135 (illuminated controlmec)
The LEDs on the module are either single colour LED (the same as used in 5 series switches - see specifi-cations in the catalogue p. 46) or RGB LEDs (19-237/R6GHBHC-A04/2T from Everlight Electronics CO. LTD - see specifications on p.4-7 in this PCN).
SW3
SW2
SW5
SW4SW1
J1
J2
40
32
20
3,5
46
,733
Ø3,2 (x4)
10
1,5PCB
7,2
108- mm
34,25Ø
SW3
SW2
SW5
SW4SW1
J1
J2
40
32
20
3,5
46
,733
Ø3,2 (x4)
10
1,5PCB
7,2
108- mm
34,25Ø
7,2
10
46,7
40
32
33
3,5
Ø3,2 (x4)
12,5 12,5
12,5
12,520
Ø3,2 (x4)
29,5Ø
46
,7
40
20
33
3,5 32
10
7,2
1,5PCB
6,90,1
Ø3,2 (x4)
29,5Ø
46
,7
40
20
33
3,5 32
10
7,2
1,5PCB
6,90,1
Ø3,2 (x4)
29,5Ø
41,1Ø
46
,7
40
20
33
3,5
32
10
7,2
1,5PCB
6,90,05
SW1SW2
SW3
SW4
SW5
MEC A/S www.mec.dk Page 2/7
PRODUCT CHANGE NOTIFICATION No 6.107/01-2014
SW3
SW2
SW5
SW4SW1
J1
J2
40
32
20
3,5
46
,733
Ø3,2 (x4)
10
1,5PCB
7,2
108- mm
34,25Ø
SW3
SW2
SW5
SW4SW1
J1
J2
40
32
20
3,5
46
,733
Ø3,2 (x4)
10
1,5PCB
7,2
108- mm
34,25Ø
illuminated and non-illuminated Navimec module
Non-illuminated Sealed Controlmec module (Unsealed version also available)
illuminated non-Sealed Controlmec module (Sealed version also available)
SW1SW2
SW3
SW4
SW5
1,5PCB
108- mm
105
30
,3
0,1
Ø
6,90,1
1,5PCB 2
5
10
6,90,1
21,5PCB
10
5
30
,3
0,1
Ø
1,5PCB
108- mm
10
5
30
,3
0,1
Ø
6,90,1
1,5PCB 2
5
10
6,90,1
21,5PCB
10
5
30
,3
0,1
Ø
PCB Part no. 9810130
PCB Part no. 9810130
PCB Part no. 9810135
Connectors on the module are Molex picoflex series 90816-0320 for switches and 90816-0316 for additional LEDs.We recommend using:Cable socket: 90327-0320 for switches and 90327-0316 for additional LEDs
Circuit diagram for switches Circuit diagram for additional LEDs for controlmec™
