· Web viewASTM D792 - For Density and Specific Gravity (Relative Density) of Plastics by...

SECTION 08 84 00PLASTIC GLAZING INCLUDING MULTIWALL, FRAMING, AND ACCESSORIES

Display hidden notes to specifier. (Don't know how? Click Here)

Copyright 2019 - 2019 ARCAT, Inc. - All rights reserved

PART 1 GENERAL

1.1 SECTION INCLUDES

A. Acrylic sheets.

B. Polycarbonate sheets.

C. Multiwall Polycarbonate sheets.

D. Framing Systems and accessories.

1.2 RELATED SECTIONS

A. Section 07 91 23 - Backer Rods.

B. Section 08 40 00 - Entrances, Storefronts, and Curtain Walls.

C. Section 11 98 21 - Detention Windows.

D. Section 08 57 00 - Hurricane Resistant Windows*.

E. Section 08 81 13 - Decorative Glass Glazing.

F. Section 08 83 00 - Mirrors.

G. Section 08 88 56 - Ballistics-Resistant Glazing.

H. Section 08 88 56 - Ballistic Resistant Glazing.

I. Section 08 44 23 - Structural Sealant Glazed Curtain Wall.

1.3 REFERENCES

08 84 00-1

A. ASTM International (ASTM): Standard Test Methods.1. ASTM C177 - For Steady-State Heat Flux Measurements and Thermal Transmission

Properties by Means of the Guarded-Hot-Plate Apparatus.2. ASTM D149 - For Dielectric Breakdown Voltage and Dielectric Strength of Solid

Electrical Insulating Materials at Commercial Power Frequencies.3. ASTM D150 - For AC Loss Characteristics and Permittivity (Dielectric Constant) of

Solid Electrical Insulation.4. ASTM D256 - For Determining the Izod Pendulum Impact Resistance of Plastics.5. ASTM D257 - For DC Resistance or Conductance of Insulating Materials.6. ASTM D495 - For High-Voltage, Low-Current, Dry Arc Resistance of Solid Electrical

Insulation.7. ASTM D542 - For Index of Refraction of Transparent Organic Plastics.8. ASTM D570 - For Water Absorption of Plastics.9. ASTM D635 - For Rate of Burning and/or Extent and Time of Burning of Plastics in a

Horizontal Position.10. ASTM D638 - For Tensile Properties of Plastics.11. ASTM D648 - For Deflection Temperature of Plastics Under Flexural Load in the

Edgewise Position.12. ASTM D695 - For Compressive Properties of Rigid Plastics.13. ASTM D696 - For Coefficient of Linear Thermal Expansion of Plastics Between 30C

and 30C with a Vitreous Silica Dilatometer.14. ASTM D732 - For Shear Strength of Plastics by Punch Tool.15. ASTM D746 - For Brittleness Temperature of Plastics and Elastomers by Impact.16. ASTM D785 - For Rockwell Hardness of Plastics and Electrical Insulating Materials.17. ASTM D790 - For Flexural Properties of Unreinforced and Reinforced Plastics and

Electrical Insulating Materials.18. ASTM D792 - For Density and Specific Gravity (Relative Density) of Plastics by

Displacement.19. ASTM D1003 - For Haze and Luminous Transmittance of Transparent Plastics.20. ASTM D1929 - For Determining Ignition Temperature of Plastics.21. ASTM D1044 - For Resistance of Transparent Plastics to Surface Abrasion.22. ASTM D1746 - For Transparency of Plastic Sheeting.23. ASTM D1929 - For Determining Ignition Temperature of Plastics.24. ASTM D3763 - For High Speed Puncture Properties of Plastics Using Load and

Displacement Sensors.25. ASTM E84 - For Surface Burning Characteristics of Building Materials.26. ASTM E132 - For Poisson's Ratio at Room.27. ASTM E162 - For Surface Flammability of Materials Using a Radiant Heat Energy

Source.28. ASTM E662 - For Specific Optical Density of Smoke Generated by Solid Materials.29. ASTM F1233 - For Security Glazing Materials And Systems.30. ASTM F1915 - For Glazing for Detention Facilities.31. ASTM F1913 - Standard Specification for Vinyl Sheet Floor Covering Without

Backing.

B. American National Standards Institute (ANSI):1. ANSI Z26. - American National Standard for Safety Glazing Materials for Glazing

Motor Vehicles and Motor Vehicle Equipment Operating on Land Highways - Safety Code.

C. Building Officials and Code Administrators International, Inc. (BOCA).

D. European Standard (EN):1. EN14500 - Blinds and shutters. Thermal and visual comfort. Test and calculation

methods.

08 84 00-2

E. European Union's Directive 2002/95/EC, the Restriction of the Use of certain Hazardous Substances in Electrical and Electronic Equipment (RoHS).

F. Food and Drug Administration (FDA):1. FDA 21 CFR Part 177.1010 - Acrylic and modified acrylic plastics, semirigid and rigid.

G. International Conference of Building Officials (ICBO).

H. International Electrotechnical Commission (IEC):1. IEC 93 - Methods of test for volume resistivity and surface resistivity of solid electrical

insulating materials.2. IEC 243 - Methods of test for electric strength of solid insulating materials - Part 1:

Test at power frequencies.

I. International Standards Organization (ISO):1. ISO 62 - Plastics - Determination Of Water Absorption.2. ISO 178 - Plastics - Determination Of Flexural Properties.3. ISO 179 - Plastics - Determination Of Charpy Impact Properties - Part 1: Non-

Instrumented Impact Test.4. ISO 180 - Plastics - Determination of Izod impact strength.5. ISO 306 - Plastics - Thermoplastic materials - Determination of Vicat softening

temperature (VST).6. ISO 489A - Plastics - Determination Of Refractive Index.7. ISO 527 - Plastics - Determination Of Tensile Properties - Part 1: General Principles.8. ISO 717 - Acoustics - Rating of sound insulation in buildings and of building elements

- Part 1: Airborne sound insulation.9. ISO 1183 - Plastics - Methods for determining the density of non-cellular plastics -

Part 1: Immersion method, liquid pycnometer method and titration method;10. ISO 2039- Plastics - Determination of hardness - Part 1: Ball indentation method.

J. United State Military Standard Commercial Item Description (CID):1. CID A-A-59502 - Plastic Sheet , Polycarbonate.

K. National Fenestration Rating Council (NFRC):1. NFRC 100 - Procedure for Determining Fenestration Product U-Factors

L. National Oceanic and Atmospheric Administration (NOA)

M. Underwriters Laboratories (UL):1. UL 94 - Standard for Tests for Flammability of Plastic Materials for Parts in Devices

and Appliances.2. UL 752 - Standard for Bullet-Resisting Equipment.

1.4 SUBMITTALS

A. Submit under provisions of Section 01 30 00 - Administrative Requirements.

B. Product Data:1. Manufacturer's data sheets on each product to be used.2. Preparation instructions and recommendations.3. Storage and handling requirements and recommendations.4. Typical installation methods.

C. Verification Samples: Two representative units of each type, size, pattern and color.

D. Shop Drawings: Include details of materials, construction and finish. Include relationship with adjacent construction.

08 84 00-3

1.5 QUALITY ASSURANCE

A. Manufacturer Qualifications: Company specializing in manufacturing products specified in this section with a minimum five years documented experience.

B. Installer Qualifications: Company specializing in performing Work of this section with minimum two years documented experience with projects of similar scope and complexity.

C. Source Limitations: Provide each type of product from a single manufacturing source to ensure uniformity.

D. Mock-Up: Construct a mock-up with actual materials in sufficient time for Architect's review and to not delay construction progress. Locate mock-up as acceptable to Architect and provide temporary foundations and support.1. Intent of mock-up is to demonstrate quality of workmanship and visual appearance.2. If mock-up is not acceptable, rebuild mock-up until satisfactory results are achieved.3. Retain mock-up during construction as a standard for comparison with completed

work.4. Do not alter or remove mock-up until work is completed or removal is authorized.

1.6 PRE-INSTALLATION CONFERENCE

A. Convene conference two weeks before scheduled commencement of Work. Attendees to include Architect, Contractor and trades involved. Agenda shall include schedule, responsibilities, critical path items and approvals.

1.7 DELIVERY, STORAGE, AND HANDLING

A. Store and handle in compliance with manufacturer's instructions and recommendations.

B. Protect from damage due to weather, excessive temperature, and construction operations.

1.8 PROJECT CONDITIONS

A. Maintain environmental conditions (temperature, humidity, and ventilation) within limits recommended by manufacturer for optimum results. Do not install products under environmental conditions outside manufacturer's recommended limits.

PART 2 PRODUCTS

2.1 MANUFACTURERS

A. Acceptable Manufacturer: A&C Plastics, Inc., which is located at: 6135 Northdale; Houston, TX 77087; Toll Free Tel: 888-702-6028; Email:request info ([email protected]); Web:https://www.acplasticsinc.com

B. Substitutions: Not permitted.

C. Requests for substitutions will be considered in accordance with provisions of Section 01 60 00 - Product Requirements.

2.2 ACRYLIC SHEETS

A. Basis of Design: Acrystar Acrylic Sheets: UV stable and suitable for interior and exterior applications.1. General Properties:

a. ROHS compliant. None of the following elements, chemicals, or compounds are to be a part of the manufacturing process or acrylic sheets; Cadmium,

08 84 00-4

Lead, Mercury, Chromium, PBB, PBDE, Other Bromine compounds.b. FDA Approval: Code 21CFR177.1010.c. Relative Density per ISO 1183: 0.688 oz per cu inch (1.19 g per cu cm).d. Water Absorption per ISO 62: 0.3 percent.

2. Mechanical Properties: At 73 degrees F (23 degrees C).a. Tensile Strength per ISO 527: 10153 psi (70 MPa).b. Elongation at Break per ISO 527: 4 percent.c. Flexural Strength per ISO 178: 16534 psi (114 MPa).d. Flexural Modulus per ISO 178: 464121 psi (3200 MPa).e. Impact Strength: Charpy-unnotched per ISO 179: 12 kJ sq m.f. Izod Impact Strength, notched per ISO 180: 1.4 kJ sq m.g. Rockwell Hardness per ISO 2039-2: 100 M scale.h. Strain: At Room Temperature:

1) Clear: 94.727 psi (6.66 kg per sq cm).2) Colored: 129.717 psi (8.12 kg per sq cm).

i. Strain: At 32 degrees F (0 degrees C):1) Clear: 136.117 psi (9.57 kg per sq cm).2) Colored: 120.330 psi (8.46 kg per sq cm).

j. Strain: Sun Drying:1) Clear: 140.100 psi (9.85 kg per sq cm).2) Colored: 63.152 psi (4.44 kg per sq cm).

k. Friction: At Room Temperature:1) Clear: 3782.417 psi (265.93 kg per sq cm).2) Colored: 3699.780 psi (260.12 kg per sq cm).

l. Friction: Sun Drying:1) Clear: 3384.306 psi (237.94 kg per sq cm).2) Colored: 3350.312 psi (235.55 kg per sq cm).

m. Friction: Graving:1) Clear: 22.847 lbs per inch (4.08 kg/cm).2) Colored: 34.270 lbs per inch (6.12 kg/cm).

n. Friction: Curving Movement:1) Clear: 347.884 lbs per inch (62.125 kg/cm).2) Colored: 292.586 lbs per inch (.2.25 kg/cm).

o. Friction: Melting Point:1) Clear: 191.3 degrees F (88.5 degrees C).2) Colored: 181.4 degrees F (83 degrees C).

p. Expansion: At 75 to 86 degrees F (24 to 30 degrees C):1) Clear: 5/10-5 mm/mm degree C.2) Colored: 6.5/10-5 mm/mm degree C.

q. Expansion: At 86 to 185 degrees F (30 to 85 degrees C):1) Clear: 9/10-5 mm/mm degree C.2) Colored: 9.5/10-5 mm/mm degree C.

r. Expansion: Flamation: Clear: None. Colored: None.1) Expansion: Hardness: 264.532 lbs per inch (47.24 kg per cm).Clear:

56.Colored: 54.4.s. Transparency: Original: Clear: 0. Colored: 15.8.t. Transparency: After Drying: Clear: 92.5 percent. Colored: 16 percent.u. Specific Gravity:

1) Clear: 0.043 lbs per cu inch (1.19 grams per cu cm).2) Colored: 0.069 lbs per cu inch (1.9 grams per cu cm).

3. Thermal Properties:a. Vicat Softening Point, ISO 306 A: 230 degrees F (110 degrees C).b. Coefficient of Thermal Expansion, ASTM D696-44: 0.0000389 in/in/F (0.00007

cm/cm/C).c. Flammability, UL94: HB.

4. Optical Properties: UV stable.

08 84 00-5

a. Light Transmission, ASTM D1003: 92 percent; 0.125 inch (3 mm).b. Refractive Index, ISO 489 A: 1.49.

5. Electrical Properties:a. Surface Resistivity, IEC 93: 1014 Ohms.b. Electrical Strength, IEC 243: 30 kV/mm.

6. Sheet Size (W x L): 48 x 96 inch (1219 x 2438 mm).7. Sheet Size (W x L): ____ x ____ inch (____ x ____ mm).8. Sheet Thickness: 0.125 inches (3.17 mm).Sheet Thickness: 0.187 inches (4.75 mm).9. Sheet Thickness: 0.220 inches (5.59 mm).10. Sheet Thickness: 0.375 inches (9.52 mm).11. Sheet Thickness: 0.500 inch (12.70 mm).12. Sheet Thickness: ____ inch (____ mm).13. Finish: Clear:14. Finish: P95. Clear Matte.15. Finish: DP9. Clear Matte.

B. Basis or Design: Acrylic Sheets: UV stable and suitable for interior and exterior applications.1. FDA Approval: FDA 21 CFR Part 177.1010. Can be in contact with food products.2. General Properties:

a. ROHS Compliant.b. Relative Density per ISO 1183: 1.19.c. Water Absorption, ASTM D570-63: 0.3 percent.d. Soluble Matter Lost after Immersion: None.

3. Mechanical Properties:a. Tensile Strength, ASTM D638-61 T.

1) Rupture: 10781.3 psi (758 kg per sq cm).2) Modulus of Elasticity: 426700.8 psi (30000 kg per sq cm).3) Elongation at Rupture: 4.5 percent.

b. Flexural Strength, D790-63.1) Rupture: 17992.5 psi (1265 kg per sq cm).2) Modulus of Elasticity: 426700.8 psi (30000 kg per sq cm).

c. Impact Strength, ASTM D256-56.1) Falling Ball Impact: 11.4 psi (0.8 kg per sq cm).2) Falling Dart Impact per ANZI/SAE Z26.1 Dart; Single Impact Vertical

Drop, 196 grams at 6 feet: Passed. No visible damage.d. Rockwell Hardness, ASTM D785-62: M 100.e. Compressive Strength, ASTM D695-63T:

1) Yield: 17921.4 psi 91260 kg per sq cm).2) Modulus of Elasticity: 426700.8 psi (30000 kg per sq cm).

f. Shear Strength, ASTM D732-46: 8889.6 psi 9625 kg per sq cm).g. Specific Gravity, ASTM 792-60 T:

1) Clear: 0.043 lbs per cu inch (1.19 grams per cu cm).2) Colored: 0.069 lbs per cu inch (1.9 grams per cu cm).

4. Thermal Properties:a. Hot Forming Temperature: 284 to 356 degrees F (140 to 180 degrees C).b. Heat Distortion, ASTM D648 at Temperature 35.6 degrees F (2 degrees C) and

264 psi (1820 kPa): 212 degrees F (100 degrees C.).c. Coefficient of Thermal Expansion, ASTM D696-44: 0.0000389 in/in/F (0.00007

cm/cm/C).d. Burning Rate, ASTM D635: 1.3 inches (33 mm) per min.e. Specific Heat: 0.35 BTU / lbs / degrees F (0.35 Cal / gr / degrees C).

5. Optical Properties: UV stable.a. Light Transmission, ASTM D1003-61: Parallel: 92 percent (3 mm). Total: 93

percent. Haze: 1 percent.b. Refractive Index, ASTM 542-50: 1.49.

6. Electrical Properties:

08 84 00-6

a. Surface Resistivity at 82.4 degrees F (28 degrees C) and 75 percent Relative Humidity, ASTM D257: Less than 10E16 ohms.

b. Volume Resistivity Dielectric Strength, D257: 15E15 Ohm cm.7. Short Time Test, ASTM D149-64: 20 kV/mm.8. Arc Resistance, D495-61: No Track.9. Sheet Thickness: 0.060 inch (1.5 mm). Color: Clear.

a. Dimensions (W x L): 48 x 96 inches (1219 x 2438 mm).b. Dimensions (W x L): 50 x 120 inches (1270 x 3048 mm).c. Dimensions (W x L): 62 x 120 inches (1575 x 3048 mm).d. Dimensions (W x L): 74 x 96 inches (1880 x 2438 mm).e. Dimensions (W x L): 74 x 120 inches (1880 x 3048 mm).

10. Sheet Thickness: 0.125 inch (3 mm).a. Dimensions (W x L): 48 x 96 inches (1219 x 2438 mm).b. Dimensions (W x L): 50 x 120 inches (1270 x 3048 mm).c. Dimensions (W x L): 74 x 98 inches (1880 x 2489 mm).d. Dimensions (W x L): 74 x 120 inches (1880 x 3048 mm).e. Color: Clear.f. Color: As determined by the Architect from manufacturer's standard offerings.

11. Sheet Thickness: 0.187 inch (4.75 mm).a. Dimensions (W x L): 48 x 96 inches (1219 x 2438 mm).b. Dimensions (W x L): 50 x 120 inches (1270 x 3048 mm).c. Dimensions (W x L): 74 x 98 inches (1880 x 2489 mm).d. Dimensions (W x L): 74 x 120 inches (1880 x 3048 mm).e. Color: Clear.f. Color: As determined by the Architect from manufacturer's standard offerings.


13. Sheet Thickness: 0.750 inch (19.05 mm). Color: Clear.a. Dimensions (W x L): 48 x 96 inches (1219 x 2438 mm).b. Dimensions (W x L): 50 x 120 inches (1270 x 3048 mm).c. Dimensions (W x L): 62 x 120 inches (1575 x 3048 mm).d. Dimensions (W x L): 74 x 96 inches (1880 x 2438 mm).e. Dimensions (W x L): 74 x 120 inches (1880 x 3048 mm).



16. Sheet Thickness: 0.625 inch (15.88 mm). Color: Clear.a. Dimensions (W x L): 48 x 96 inches (1219 x 2438 mm).b. Dimensions (W x L): 50 x 120 inches (1270 x 3048 mm).c. Dimensions (W x L): 62 x 120 inches (1575 x 3048 mm).

08 84 00-7

d. Dimensions (W x L): 74 x 96 inches (1880 x 2438 mm).e. Dimensions (W x L): 74 x 120 inches (1880 x 3048 mm).

17. Sheet Thickness: 0.750 inch (19.05 mm). Color: Clear.a. Dimensions (W x L): 48 x 96 inches (1219 x 2438 mm).b. Dimensions (W x L): 50 x 120 inches (1270 x 3048 mm).c. Dimensions (W x L): 62 x 120 inches (1575 x 3048 mm).d. Dimensions (W x L): 74 x 96 inches (1880 x 2438 mm).e. Dimensions (W x L): 74 x 120 inches (1880 x 3048 mm).

18. Sheet Thickness: 1.000 inch (25.40 mm). Clear.a. Dimensions (W x L): 48 x 96 inches (1219 x 2438 mm).








2.3 POLYCARBONATE SHEETS:

A. Tuffack Polycarbonate, Makrolon AR. Abrasion and UV resistant sheet with glass-like surface and high impact strength. Resistant to yellowing and hazing.1. Standards Compliance: CID A-A-59502. Type III; Marr Resistant, UV Stabilized Sheet,

Class 1, Grade A, High abrasion.2. Physical and Mechanical Properties:

a. Specific Gravity, ASTM D792: 1.2b. Light Transmission, ASTM D1003: Clear 1/8 inch (3 mm) thick; 86 percent.c. Light Transmission, ASTM D1003: Gray or Bronze; 50 percent.d. Chemical Resistance, ANSI Z26.1: Pass.e. Taber Abrasion, 100 Cycles CS10, ASTM D1044: 1 to 2 percent.f. Tensile Strength, Ultimate , ASTM D638: 9,500 psi (65500 kPa).g. Flexural Strength, ASTM D790: 13,500 psi (93079 kPa).h. Compressive Strength, ASTM D695: 12,500 psi (86184 kPa).i. Modulus of Elasticity, ASTM D638: 340,000 psi (2344 MPa).j. Poisson's Ratio: 0.38.k. Izod Impact Strength, ASTM D256 at 1/8 inch (3 mm):

1) Notched: 12 to 16 Ft-lbs/in (0.64 to 0.85 Nm/mm).2) Unnotched: 60 Ft-lbs/in (3.59 Nm/mm) No failure.

l. Instrumented Impact, ASTM D3763, 1/8 inch (3 mm): 45 ft-lbs (61 Nm).3. Thermal Properties:

a. Coefficient of Thermal Expansion, ASTM D696: 0.0000375 in/in/F.b. Heat Deflection Temperature, ASTM D648, at 264 psi (1820 kPa): 270 degrees

F (132 degrees C).c. Heat Deflection Temperature,, ASTM D648, at 66 psi (455 kPa): 280 degrees F

(138 degrees C).4. Electrical Properties:

a. Dielectric Constant, ASTM D150 at 10 Hz: 2.96.b. Dielectric Constant, ASTM D150 at 60 Hz: 3.17.c. Volume Resistivity, ASTM D257: 8.2 x 10E16 Ohm-cm.

08 84 00-8

d. Dissipation Factor, ASTM D150 at 60 Hz: 0.0009.e. Dissipation Factor, ASTM D150 at 1 MHz: 0.01.f. Arc Resistance, ASTM D495:

1) Stainless Steel Strip Electrode: 10 to 11 seconds.2) Tungsten Electrodes: 120 seconds.

g. Dielectric Strength, ASTM D149: In air, 125 mils: 380 V/mil.5. Flammability:

a. Horizontal Burn, AEB, ASTM D635: Less than 1 inch (25 mm).b. Ignition Temperature, ASTM D1929:

1) Self: 1070 degrees F (576.7 degrees C).2) Flash: 870 degrees F (465.6 degrees C).

c. Flame Class, Ul 94 at 0.060 inch (1.5 mm) and 0.236 inch (6 mm): HB.

B. Tuffack Polycarbonate, Makrolon FD. Clear, non-UV stabilized sheet, complying with FDA and NSF 51 requirements. Close gauge tolerance control, high impact strength and heat resistance. Suitable for medical and food processing environments.1. Standards Compliance: CID A-A-59502. Type 1, Class 2, Non-UV Stabilized.2. Physical and Mechanical Properties:

a. Specific Gravity, ASTM D792: 1.2.b. Light Transmission, ASTM D1003, Clear 1/8 inch (3 mm): 86 percent.c. Water Absorption, ASTM D570, Equilibrium, 24 hours: 0.15 percent.d. Impact Resistance: 250 times that of float glass. 30 times that of acrylic.e. Tensile Strength, Yield, ASTM D638: 9000 psi (62053 kPa).f. Tensile Strength, Ultimate, ASTM D638: 9500 psi (65500 kPa).g. Tensile Modulus, ASTM D638: 345000 psi (2378691 kPa).h. Flexural Strength, ASTM D790: 13500 psi (93079 kPa).i. Flexural Modulus, ASTM D790: 345000 psi (2378691 kPa).j. Compressive Strength, ASTM D695: 12500 psi (86184 kPa).k. Compressive Modulus, ASTM D695: 345000 psi (2374691 kPa).l. Elongation, ASTM D63: 110 percent.m. Poisson's Ratio: 0.38n. Izod Impact Strength, ASTM D256 at 1/8 inch (3 mm):


3. Thermal Properties:a. Coefficient of Thermal Expansion, ASTM D696: 0.0000375 in/in/degrees F

(0.0000675 mm/mm/degrees C).b. Coefficient of Thermal Conductivity, ASTM C177: 1.35 Btu/hr/sq ft/F (7.66 W/sq

m/C).c. Heat Deflection Temperature, ASTM D648 at 264 psi: 270 degrees F (132

degrees C).d. Heat Deflection Temperature, ASTM D648 at 66 psi: 280 degrees F (138

degrees C).4. Electrical Properties:

a. Dielectric Constant, at 10 Hz ASTM D150: 2.96.b. Dielectric Constant, at 60 Hz ASTM D150: 3.17.c. Volume Resistivity ASTM D257: 8.2 x 10E16 Ohm-cm.d. Dissipation Factor, at 60 Hz ASTM D150: 0.0009.e. Dissipation Factor, at 1 MHz ASTM D150: 0.01.f. Arc Resistance, ASTM D495: Stainless Steel Strip Electrode: 10 to 11 seconds.

Tungsten Electrodes: 120 seconds.5. Dielectric Strength, ASTM D149, in air, 125 mils (3.17 mm): 380 V/mil.6. Tuffack Polycarbonate, Makrolon GP. Polished surface, UV stabilized, and

transparent lightweight thermoformable sheet. High impact strength, dimensionally stable, temperature resistance. Easy to fabricate and decorate. Limited Product Warranty: Five year against breakage. Standards Compliance: CID A-A-59502. Type

08 84 00-9

1, , Class 1, UV Stabilized.7. Physical Mechanical Properties:

a. Specific Gravity, ASTM D792: 1.2.b. Refractive Index, ASTM D542: 1.586.c. Light Transmission, ASTM D1003:

1) Clear at 0.118 inch (3 mm): percent.2) Gray, I30 at 0.118 inch (3 mm): 50 percent.3) Bronze, K09 at 0.118 inch (3 mm): 50 percent.4) Dark Gray, I35 at 0.118 inch (3 mm): 18 percent.5) Water Absorption, ASTM D 570 after 24 hours: 0.15 percent.

d. Poisson's Ratio, ASTM E132: 0.38.e. Tensile Strength, Ultimate, ASTM D638: 9,500 psi (65500 kPa).f. Tensile Strength, Yield, ASTM D638: 9,000 psi (62053 kPa).g. Tensile Modulus, ASTM D638: 340,000 psi (2344217 kPa).h. Elongation, ASTM D638: 110 percent.i. Flexural Strength, ASTM D790: 13,500 psi (93079 kPa).j. Flexural Modulus, ASTM D790: 345,000 psi (2378691 kPa).k. Compressive Strength, ASTM D695: 12,500 psi (86184 kPa).l. Compressive Modulus, ASTM D695: 345,000 psi (2378691 kPa).m. Izod Impact Strength, ASTM D256 at 1/8 inch (3 mm):

1) Notched: 18 Ft-lbs/in (0.96 Nm/mm).2) Unnotched: 60 Ft-lbs/in (3.59 Nm/mm) No failure.

n. Instrumented Impact, ASTM D3763 at 0.125 inch (3 mm): 47 ft lbs (63.72 Nm).o. Shear Strength, Ultimate, ASTM D732: 10,000 psi (68947 kPa).p. Shear Strength, Yield, ASTM D732: 6,000 psi (41368 kPa).q. Shear Modulus, ASTM D732: 114,000 psi (7860002 kPa).r. Rockwell Hardness, ASTM D785: M70 and R118

8. Thermal Properties:a. Coefficient of Thermal Expansion, ASTM D696: 0.0000375 inch per inch per

degrees F.b. Coefficient of Thermal Conductivity, ASTM C177: 1.35 BTU/hr/sq ft/degrees F

(7.66 (W/sq m/degrees C).c. Heat Deflection Temperature, ASTM D648: At 264 psi (1820 kPa): 270 degrees

F. At 66 psi (455 kPa): 280 degrees F.d. Brittleness Temperature, ASTM D746: Minus 200 degrees F (minus 129

degrees C).e. Shading Coefficient, NFRC 100 at 0.236 inch (6 mm) Thick: Clear; 0.97. Gray

or Bronze; 0.77.f. U factor, NFRC 100 at 0.236 inch (6 mm):

1) Summer: 0.85 BTU/hr/sq ft/degrees F (4.82 W/sq m/degrees C).2) Winter: 0.92 BTU/hr/sq ft/degrees F (5.22 W/sq m/degrees C).

g. U factor, NFRC 100 at 0.375 inch (9.5 mm):1) Summer: 0.78 BTU/hr/sq ft/degrees F (4.43 W/sq m/degrees C).2) Winter: 0.85 BTU/hr/sq ft/degrees F (4.82 W/sq m/degrees C).

9. Electrical Properties:a. Dielectric Constant, ASTM D150 at 10 Hz: 2.96. At 60 Hz: 3.17.b. Volume Resistivity, ASTM D257: 8.2 x 10E16 Ohm-cm.c. Dissipation Factor, ASTM D150 at 60 Hz: 0.0009.d. Arc Resistance, ASTM D495: Stainless Steel Strip electrode: 10 seconds.

Tungsten Electrodes: 120 seconds.e. Dielectric Strength, ASTM D149 in air at 0.125 inch (3 mm): 380 V/mil.

10. Flammability:a. Horizontal Burn, AEB, ASTM D635: Less than 1 inch (25 mm).b. Ignition Temperature, ASTM D1929: Self: 1022 degrees F (550 degrees C).

Flash: 824 degrees F (440 degrees C).c. Flame Class, UL 94 at 0.060 inches (1.5 mm): HB. At 0.394 inches (10 mm): V-

08 84 00-10

0.

C. Tuffack Polycarbonate, Hygard BR1000 sheet. Ballistic glazing, 4-ply laminate. Resists spalling, marring, chemical attack, graffiti and white-out after ballistic impacts.1. Limited Product Warranty: 7 year against coating failure, yellowing, and hazing.2. Four-Ply Construction:

a. Makrolon AR-1: 1/8 inch (3 mm) abrasion resistant surface.b. Makrolon: 3/8 inch (9.5 mm) polycarbonate sheet.c. Makrolon: 3/8 inch (9.5 mm) polycarbonate sheet.d. Makrolon AR-1: 1/8 inch (3 mm) abrasion resistant surface.e. Polyurethane bonding interlayers.

3. Properties:a. Gauge: 1.05 inches (26.7 mm) plus or minus 5 percent.b. Weight 6.5 lbs per sq ft (31.74 kg per sq m).c. Shading Coefficient: 0.85.d. U-Value 0.60.e. Light Transmission 72 percent.

4. Ballistic Property: UL 752 Level 2 (.357 Magnum jacketed lead soft point).5. Forced Entry and Containment:

a. ASTM F 1233.08 Class 5 Body Passage, and Class 2.4 Contraband Passage.b. ASTM F 1915.03 Grade 1.c. H.P. White TP 0500.03 Level IV Sequence 43.

6. Agency Information:a. UL File: BP6864.b. Combustibility Class CC1.c. Miami-Dade NOA: 12-0605.05.

7. Sheet Size: 48 x 60 inch (1219 x 1524 mm).8. Sheet Size: 48 x 72 inch (1219 x 1829 mm).9. Sheet Size: 38 x 78 inch (965 x 1981 mm).10. Sheet Size: 38 x 96 inch (965 x 2438 mm).11. Sheet Size: 48 x 96 inch (1219 x 2438 mm).12. Sheet Size: 60 x 72 inch (1524 x 1829 mm).13. Sheet Size: 60 x 96 inch (1524 x 2438 mm).

D. Tuffack Polycarbonate, Hygard BR1250 four-ply sheet. Security. UL Listed Level III bullet-resisting glazing. Hard coated with abrasion and UV resistant surfaces for extended service life in harsh environments.1. Forced Entry Ballistics Ratings:

a. H.P. WHITE TP0500.01 Level V.b. H.P. WHITE TP0500.01 Level C Ballistics (.44 magnum).c. ASTM F 1233 Class V Step 38 Ballistics (.44 magnum).d. UL752 Level III SPSA .44 Magnum.

2. Four-ply Construction:a. Makrolon AR: 1/8 inch (3 mm) abrasion resistant surface.b. Makrolon: 1/2 inch (13 mm) polycarbonate sheet.c. Makrolon: 1/2 inch (13 mm) polycarbonate sheet.d. Makrolon AR: 1/8 inch (3 mm) abrasion resistant surface.e. Polyurethane bonding interlayers.f. Flexural Strength, ASTM D790: 13,500 psi (93079 kPa).g. Self-Ignition Temperature, ASTM D1929: 1077 degrees F (580 degrees C).h. Flash Ignition Temperature, ASTM D1929: 872 degrees F (466 degrees C).i. Conform with ICBO and BOCA.j. Model Building Codes as a CC-1 rated light transmitting plastic.

3. Physical Properties:a. Gauge/Tolerance: 1.30 inches (33 mm) plus or minus 5 percent.b. Weight: 8.1 lbs per sq ft (39.55 kg per sq m).

08 84 00-11

c. Shading Coefficient: 0.81.d. Light Transmittance; Clear: 67 percent.e. Colors Standard: Clear.f. Custom Colors: As determined by the Architect.

4. Sheet Size: 38 x 96 inch (965 x 2438 mm).5. Sheet Size: 48 x 60 inch (1219 x 1524 mm).6. Sheet Size: 48 x 72 inch (1219 x 1829 mm).7. Sheet Size: 48 x 96 inch (1219 x 2438 mm).8. Sheet Size: 60 x 96 inch (1524 x 2438 mm).

E. Tuffack Polycarbonate, Hygard BR750 sheet. A two-ply polycarbonate and acrylic sheet for security applications requiring UL Listed Level 1 bullet resisting glazing. Abrasion and UV resistant surfaces for extended service life in harsh environments.1. Ballistics Rating:

a. UL752 Level I MPSA 0.354 inch (9 mm).b. H.P. WHITE TP0500.02 Level B Ballistics 0.354 inch (9 mm).

2. Laminate Construction:a. Polycarbonate Sheet: 1/8 inch (3 mm) with high AR abrasion-resistant surface.b. Acrylic Sheet: 1/2 inch (12.7 mm).c. Polycarbonate Sheet: 1/8 inch (3 mm) with high AR abrasion-resistant surface.d. Polyurethane bonding interlayers.

3. Physical Properties:a. Gauge/Tolerance: .780 inch (19.81 mm) plus or minus 8 percent.b. Weight: 5.1 lbs per sq ft (24.9 kg per sq m).c. Shading Coefficient: 0.89.d. Percent Light Transmittance: Clear; 88 percent.e. Color: Clear.f. Color: As determined by the Architect.

4. Sheet Sizes: 38 x 96 inches (965 x 2438 mm).5. Sheet Sizes: 48 x 60 inches (1219 x 1524 mm).6. Sheet Sizes: 48 x 96 inches (1219 x 2438 mm).7. Sheet Sizes: 48 x 72 inches (1219 x 1829 mm).8. Sheet Sizes: 60 x 96 inches (1524 x 2438 mm).

F. Tuffack Polycarbonate, Hygard CG375 sheet. 2-ply containment grade sheet. 3/8 inches (10 mm) laminate. Resists spalling and white-out after repeated high force impacts,1. Meets ASTM F 1915 and HP White TP 0500.2. Exterior surfaces: Proprietary AR Hardcoat that facilitates cleaning and resists

marring, chemical attack, and graffiti. Limited Product Warranty: 7 year against coating failure. yellowing, and hazing. The terms of the warranty are available upon request.

3. Laminate Construction:a. Makrolon AR-I 3/16 inch (4.76 mm) abrasion resistant surface.b. Polyurethane bonding interlayer.c. Makrolon AR-I 3/16 inch (4.76 mm) abrasion resistant surface.

4. Sheet Sizes: 38 x 96 inches (965 x 2438 mm).5. Sheet Sizes: 48 x 96 inches (1219 x 2438 mm).6. Sheet Sizes: 60 x 96 inches (1524 x 2438 mm).7. Typical Properties:

a. Gauge and Tolerance: 0.390 inch (9.91 mm) plus or minus 5 percent.b. Weight: 2.4 lbs per sq ft (11.72 kg per sq m).c. Shading Coefficient: 0.92.d. U-Value: 0.84.e. Light Transmission: 88 percent. Clear.

8. Force Entry and Containment:a. ASTM F 1233.08 Class 1.4 Contraband Passage, and Class 2.8 Body

08 84 00-12

Passage.b. ASTM F 1913.03 Grade 3.c. HP White TP 0500.03 Level 1 Sequence 13.

9. Agency Information:a. Combustibility Class CACI.b. Miami-Dade NOA 12-0605.05.

G. Tuffack Polycarbonate, Hygard CG500 sheet. A three-ply sheet for architectural security glazing. Abrasion and UV resistant hard coated surfaces for extended service life.1. Force Entry, Ballistics Ratings:

a. H.P. WHITE TP 0500.01 Level II Step 12 and Level A Ballistics (.38 Special).b. ASTM F 1233 Class III Step 15.

2. Laminate Construction:1) Polycarbonate Sheet: 1/8 inch (3 mm) with abrasion-resistant surface.2) Polycarbonate Sheet: 1/4 inch (6 mm).3) Polycarbonate Sheet: 1/8 inch (3 mm) with abrasion-resistant surface.4) Polyurethane bonding interlayers.

b. Flexural Strength, ASTM D790: 13,500 psi (93079 kPa).c. High performance abrasion-resistant surfaces.d. Self-Ignition Temperature: 1077 degrees F (580 degrees C).e. Flash Ignition Temperature, ASTM D1929: 872 degrees F (467 degrees C).f. Conform with ICBO and BOCA Model Building Codes as a CC-1 rated

Approved Light Transmitting Plastic.3. Physical Properties:

a. Gauge and Tolerance: 0.530 inches (13.46 mm) plus or minus 5 percent.b. Weight: 3.3 lbs per sq ft (16.1 kg per sq m).c. Shading Coefficient: .90 percent.d. Light Transmittance: 83 percent. Clear.e. Color: Clear.f. Color: As determined by the Architect.g. Sheet Sizes: 38 x 96 inches (965 x 2438 mm).h. Sheet Sizes: 48 x 96 inches (1219 x 2438 mm).i. Sheet Sizes: 60 x 96 inches (1524 x 2438 mm).

H. Tuffack Polycarbonate, Hygard CG750 sheet. A three-ply polycarbonate for architectural security glazing. Abrasion and UV resistant hard coated surfaces.1. Forced Entry, Ballistics Ratings:

a. H.P. WHITE TP 0500.01 Level IV Step .31 and Level B Ballistics (.9 mm).b. ASTM F 1233 Class IV Step 26.

2. Laminate Construction:a. Polycarbonate Sheet: 1/8 inch (3 mm) with abrasion-resistant surface.b. Polycarbonate Sheet: 1/2 inch (12.7 mm).c. Polycarbonate Sheet: 1/8 inch (3 mm) with abrasion-resistant surface.d. Polyurethane bonding interlayers.

3. Physical Properties:a. Flexural Strength, ASTM D790: 13,500 psi (93079 kPa).b. High performance abrasion-resistant surfaces.c. Self-Ignition Temperature: 1077 degrees F (580 degrees C).d. Flash Ignition Temperature, ASTM D1929: 872 degrees F (467 degrees C).e. Conform with ICBO and BOCA Model Building Codes as a CC-1 rated

Approved Light Transmitting Plastic.4. Mechanical Properties:

a. Gauge/Tolerance .780 inch (19.81 mm) plus or minus 5 percent.b. Weight 4.9 lbs per sq ft (23.9 kg per sq m).c. Shading Coefficient: .87 percent.d. Light Transmittance: 77 percent. Clear.

08 84 00-13

e. Color: Clear.f. Color: As determined by the Architect.g. Sheet Sizes: 38 x 96 inches (965 x 2438 mm).h. Sheet Sizes: 48 x 96 inches (1219 x 2438 mm).i. Sheet Sizes: 60 x 96 inches (1524 x 2438 mm).

I. Tuffack Polycarbonate, Makrolon LD sheet. Excellent light uniformity without sacrificing light transmission. Proprietary diffuser technology eliminates visible hot spots from pinpoint LED lights in typical flat and formed sign applications. High impact strength and dimensional stability. UV resistance assures long lasting outdoor weathering performance.1. Limited Product warranty: Ten year limited product warranty against breakage.2. Regulatory Code Compliance and Certifications:

a. UL 879: Electric Sign Components UL File No. E146154.b. UL 94: Flammability UL File No. E351891.

3. Physical Properties:a. Specific Gravity, ASTM D792: 1.2.b. Light Transmission, ASTM D1003:

1) White/B27 at 0.118 inch (3 mm): 27 percent.2) White/B48 at 0.118 inch (3 mm): 50 percent.

c. Water Absorption, ASTM D570 at 24 hours: 0.15 percent.d. Color: White/ B48: 0.093 to 0.236 inches (2.36 to 6 mm).e. Color: White/ B27: 0.093 to 0.236 inches (2.36 to 6 mm).f. Color: Red/ D96: 0.118 to 0.177 inches (3 to 4.5 mm).g. Color: Red/ D99: 0.118 to 0.177 inches (3 to 4.5 mm).h. Color: Blue/ F84: 0.118 to 0.177 inches (3 to 4.5 mm).i. Color: Blue/ F85: 0.118 to 0.177 inches (3 to 4.5 mm).j. Color: Green/ H87: 0.118 to 0.177 inches (3 to 4.5 mm).k. Color: Yellow/ M72: 0.118 to 0.177 inches (3 to 4.5 mm).l. Color: Orange/ C59: 0.118 to 0.177 inches (3 to 4.5 mm).

4. Mechanical Properties:a. Tensile Strength, Ultimate, ASTM D638: 9,500 psi (65500 kPa).b. Tensile Strength, Yield, ASTM D638: 9,000 psi (62053 kPa).c. Tensile Modulus, ASTM D638: 340,000 psi (2344217 kPa).d. Elongation, ASTM D638: 110 percent.e. Flexural Strength, ASTM D790: 13,500 psi (93079 kPa).f. Flexural Modulus, ASTM D790: 345,000 psi (2378691 kPa).g. Compressive Strength, ASTM D695: 12,500 psi (86184 kPa).h. Compressive Modulus, ASTM D695: 345,000 psi (2378691 kPa).i. Izod Impact Strength, ASTM D256 at 1/8 inch (3 mm):

1) Notched: 18 ft lbs per inch (0.96 Nm per mm).2) Unnotched: 60 ft lbs per inch (3.202 Nm per mm). no Failure.

j. Instrumented Impact, ASTM D3763 at 0.125 inch (3 mm): 47 ft lbs (63.72 Nm).k. Shear Strength, Ultimate, ASTM D732: 10,000 psi (68947 kPa).l. Shear Strength, Yield, ASTM D732: 6,000 psi (41368 kPa).m. Shear Modulus, ASTM D732: 114,000 psi (7860002 kPa).n. Rockwell Hardness, ASTM D785: M70 and R118.o. Impact Resistance, ASTM D3763: 47 ft-lbs (63.7 Nm).

5. Thermal Properties:a. Coefficient of Thermal Expansion, ASTM D696: 0.0000375 in per in per



F (132 degrees C. At 66 psi (455 kPa): 280 degrees F (138 degrees C).d. Brittleness Temperature, ASTM D746: Minus 200 degrees F (minus 129

degrees C).

08 84 00-14

6. Electrical Properties:a. Dielectric Constant, ASTM D150 at 10 Hz: 2.96. At 60 Hz: 3.17.b. Volume Resistivity, ASTM D257: 8.2 x 10E16 Ohm-cm.c. Dissipation Factor, ASTM D150 at 60 Hz: 0.0009.d. Arc Resistance, ASTM D495: Stainless Steel Strip electrode: 10 seconds.

Tungsten Electrodes: 120 seconds.e. Dielectric Strength, ASTM D149 in air at .125 inch (3 mm): 380 V/mil.

7. Flammability:a. Horizontal Burn, AEB, ASTM D635: Less than 1 inch (25 mm).b. Flame Class, UL 94 at 0.093 inch (2.36 mm): V2. At 0.236 (6 mm): V0.

J. Tuffack Polycarbonate, Makrolon LF UV stable sheet.1. Sheet Thickness: from .080 inch (2 mm).2. Standards Compliance: CID A-A-59502. Type II - Flame Resistant, Class 1, UV

Stabilized. FAR 25.853 paragraphs A and B.3. Physical Properties:

a. Specific Gravity, ASTM D792: 1.2.b. Light Transmission, ASTM D1003: Clear; 86 percent.c. Haze, ASTM D1003: Clear; less than 1 percent.d. Flammability, UL 94: V-0.

4. Mechanical Properties:a. Tensile Strength, Ultimate, ASTM D638: 9,500 psi (65500 kPa).b. Flexural Strength, ASTM D790: 13,500 psi (93079 kPa).c. Compressive Strength, ASTM D695: 12,500 psi (86184 kPa).d. Compressive Modulus, ASTM D695: 345,000 psi (2378691 kPa).e. Izod Impact Strength, ASTM D256 at 1/8 inch (3 mm):


f. Instrumented Impact ASTM D3763: 45 ft-lbs (61 Nm).5. Thermal Properties:

a. Coefficient of Thermal Expansion, ASTM D696: 0.0000375 in per in per degrees F.

b. Heat Deflection Temperature, ASTM D648: At 264 psi (1820 kPa): 270 degrees F (132 degrees C. At 66 psi (455 kPa): 280 degrees F (138 degrees C).

K. Tuffack Polycarbonate, Makrolon Lumen XT sheet. Translucent with a textured surface on one side designed for lighting lenses. A combination of high light diffusion and high light transmission due to an optimized surface texture and advanced diffuser technology.1. Physical Properties:

a. Specific Gravity, ASTM D792: 1.2.b. Water Absorption at 24 hrs, ASTM D570: 0.15 percent.c. Poisson's Ratio, ASTM E132: 0.38.d. Light Transmission, ASTM D1003:

1) LC3 at 0.118 inch (3.00 mm) 85 percent.2) LC5 at 0.118 inch (3.00 mm) 77 percent.3) LC7 at 0.118 inch (3.00 mm) 62 percent.4) LW3 at 0.118 inch (3.00 mm) 90 percent.5) LW5 at 0.118 inch (3.00 mm) 81 percent.6) LW7 at 0.118 inch (3.00 mm) 67 percent.

2. Mechanical Properties:a. Tensile Strength, Ultimate ASTM D792: 1.2.b. Tensile Strength, Yield ASTM D570: 0.15 percent.c. Tensile Modulus ASTM E132: 0.38.d. Elongation, ASTM D1003: 85 percent.e. Flexural Strength, ASTM D1003: 85 percent.f. Flexural Modulus, ASTM D1003: 85 percent.

08 84 00-15

g. Instrumented Impact, ASTM D1003: 85 percent.3. Thermal Properties:

a. Coefficient of Thermal Expansion, ASTM D696: 0.0000375 in per in per degrees F.

b. Coefficient of Thermal Conductivity, ASTM C177: 1.35 BTU/hr/sq ft/degrees F (7.66 (W/sq m/degrees C).

c. Heat Deflection Temperature, ASTM D648: At 264 psi (1820 kPa): 274 degrees F (134 degrees C). At 66 psi (455 kPa): 287 degrees F (142 degrees C).

4. Electrical:a. Dielectric Constant at 10 Hz, ASTM D150: 2.98.b. Dielectric Constant at 60 Hz, ASTM D150: 2.88.c. Volume Resistivity, ASTM D257: 8.2 x 10E16 Ohm-cm.d. Dissipation Factor at 60 Hz, ASTM D150: 0.002.e. Arc Resistance, ASTM D495: Tungsten Electrodes: 125 seconds.f. Dielectric Strength, ASTM D149 in air at 0.118 inch (3 mm): 460 V/mil.

5. Flammability: Material thickness of 0.060 to 0.118 inch (1.5 to 3 mm).a. Flame Class, UL 94: V2.b. Surface Flammability, ASTM E162: Less than 100.c. Smoke Density, ASTM E662: At 1.5 min: Less than 100. At 4 min: Less than

200. At 20 min: Less than 200.d. Vertical Burn; at 12 sec, FAR 25.853: Pass.e. Horizontal Burn, 2.5 and 4.0 inch (64 and 102 mm), FAR 25.853: Pass.f. Toxic Gas Generation at 0.060 to 0.118 inch (1.5 to 3 mm), BSS 7239 and SMP

800-C: Pass.6. Diffusion and Transmission:

a. Lumen XT Grade: LC3. Diffusion, FWHM: 38 to 53 degrees.1) Transmission, ASTM D1003: 85 to 90 percent.

b. Lumen XT Grade: LC5. Diffusion, FWHM: 53 to 77 degrees1) Transmission, ASTM D003: 77 to 88 percent

c. Lumen XT Grade: LC7. Diffusion, FWHM: 86 to 135 degrees1) Transmission, ASTM D1003: 62 to 79 percent

d. Lumen XT Grade: LW3. Diffusion, FWHM: 38 to 53 degrees1) Transmission, ASTM D1003: 90 to 93 percent

e. Lumen XT Grade: LW5. Diffusion, FWHM: 53 to 77 degrees1) Transmission, ASTM D1003: 81 to 90 percent

f. Lumen XT Grade: LW7. Diffusion; FWHM: 86 to 135 degrees1) Transmission, ASTM D1003: 67 to 82 percent

L. Tuffack Polycarbonate, Makrolon Marine 5 sheet. For applications of high optical clarity, exceptional durability, and longevity in harsh marine environment.1. Low optical distortion and sight lines. Abrasion resistance, enhanced clarity, chemical

resistant. Long lasting outdoor weathering performance. High impact strength at temperatures down to minus 30 degrees F (minus 43.3 degrees C). Easily cut and sewn. Does not require gluing.Limited Product Warranty: Five year against micro-cracking, yellowing, and breakage.Physical Properties:a. Specific Gravity, ASTM D792: 1.2.b. Light Transmission, ASTM D1003: Clear at 0.060 inch (1.5 mm) 90 percent.c. Light Transmission, ASTM D1003: Clear at 0.080 inch (2.0 mm) 89 percent.d. Chemical Resistance, ANSI Z26.1: Pass.e. Taber Abrasion, 100 Cycles, Delta Haze, ASTM D1044: 2 percent.f. Impact resistance, ASTM D3763: 47.g. Abrasion Resistance: 2, Delta Haze Percentage.

2. Mechanical Properties:a. Tensile Strength, Ultimate, ASTM D638: 9,500 psi (65500 kPa).b. Modulus of Elasticity, ASTM D 638: 340,000 psi (2344217 kPa).c. Flexural Strength, ASTM D790: 13,500 psi (93079 kPa).

08 84 00-16

d. Compressive Strength, ASTM D695: 12,500 psi (86184 kPa).e. Izod Impact Strength, ASTM D256 at 1/8 inch (3 mm):


f. Instrumented Impact at 0.60 inch (15 mm) ASTM D3763: 21 ft lbs (28.5 Nm).g. Instrumented Impact at 0.80 inch (20 mm) ASTM D3763: 33 ft lbs (44.7 Nm).h. Instrumented Impact at 0.125 inch (3 mm) ASTM D3763: 47 ft lbs (63.7 Nm).i. Instrumented Impact at 0.125 inch (3 mm) at minus 30 degrees F (minus 34.4

degrees C), ASTM D3763: 50 ft lbs (67.8 Nm).j. Poisson's Ratio, ASTM E132: 0.38.k. Rockwell Hardness ASTM D785: M70 and R118.l. Chemical Resistance, ASTM D1308. Greater than 24 hours.

1) Acetone, Antifreeze (50/50), Benzene, Bleach (Clorox concentrated), Denatured Alcohol, Di (2-ethylhexyl) phthalate, Diesel Oil, Isopropyl Alcohol (IPA), Kerosene, Methyl Alcohol, Methyl Butyl Ketone, Methyl Ethyl Ketone, Methylene Chloride, Naphthalene, 1-bromo, Potassium Hydroxide - Lye (10 percent), Sodium Hydroxide (10 percent), Toluene, Turpentine, Unleaded Gasoline (87 Octane), Vinegar, Xylene, Hydrochloric Acid (20 percent), and Sulfuric Acid (20 percent).

3. Thermal Properties:a. Coefficient of Thermal Expansion, ASTM D696: 0.0000375 inch per inch per

degrees F.b. Heat Deflection Temperature, ASTM D648: At 66 psi (455 kPa): 280 degrees F.

M. Tuffack Polycarbonate, Makrolon MG Sheet. Machine Grade polycarbonate engineering plate. An amorphous thermoplastic, extremely high impact, high elasticity modulus, dimensionally stabile, and good mechanical and electrical properties.1. Standards Compliance: CID A-A-59502. Type 1, Class 1, UV Stabilized.2. Physical Properties:

a. Specific Gravity, ASTM D792: 1.2.b. Rockwell Hardness, ASTM D785: M70 and R118.c. Water Absorption, Equilibrium, at 24 hours, ASTM D570: 0.15 percent.

3. Mechanical Properties:a. Tensile Strength, Ultimate, ASTM D638: 9,500 psi (65500 kPa).b. Tensile Strength, Yield, ASTM D638: 9,000 psi (62053 kPa).c. Tensile Modulus, ASTM D638: 345,000 psi (2378691 kPa).d. Flexural Strength, ASTM D790: 13,500 psi (93079 kPa).e. Flexural Modulus, ASTM D790: 345,000 psi (2378691 kPa).f. Compressive Strength, ASTM D695: 12,500 psi (86184 kPa).g. Compressive Modulus, ASTM D695: 345,000 psi (2378691 kPa).h. Elongation, ASTM D638: 110 percent.i. Poisson's Ratio: 0.38.j. Shear Strength, Ultimate, ASTM D732: 10,000 psi (68947 kPa).k. Shear Strength, Yield, ASTM D732: 6,000 psi (41368 kPa).l. Shear Modulus, ASTM D732: 114,000 psi (7860002 kPa).




F (132 degrees C). At 66 psi (455 kPa): 280 degrees F (138 degrees C).5. Electrical Properties:

a. Dielectric Constant, ASTM D150 at 10 Hz: 2.96. At 60 Hz: 3.17.b. Volume Resistivity ASTM D257: 8.2 x 10E16 Ohm-cm.c. Dissipation Factor, ASTM D150 at 60 Hz: 0.0009.

08 84 00-17

d. Dissipation Factor, ASTM D150 at 1 MHz: 0.01.e. Arc Resistance, ASTM D495: Stainless Steel Strip electrode: 10 to 11 seconds.

Tungsten Electrodes: 120 seconds.f. Dielectric Strength, ASTM D149 in air at 0.125 inch (3 mm): 380 V/mil.

6. Flammability: Flame Class, UL 94, greater or equal to 0.375 inch (9.52 mm): V0.

N. Tuffack Polycarbonate, Makrolon OP. Lightweight thermoformable sheet. Polished surface, UV stabilized, transparent polycarbonate product. For applications requiring improved optical quality. High impact strength, dimensional stability, temperature resistance, and clarity.1. Limited Product Warranty: Five year against breakage.2. Standards Compliance: CID A-A-59502. Type 1, Class 1, UV Stabilized.3. Physical Properties:

a. Specific Gravity, ASTM D792: 1.2.b. Refractive Index, ASTM D542: 1.586.c. Light Transmission:

1) Clear at 0.118 inch (3 mm), ASTM D1003: 86 percent.2) Gray /I30 at 0.118 inch (3 mm), ASTM D1003: 50 percent.3) Bronze /K09 at 0.118 inch (3 mm), ASTM D1003: 50 percent.4) Dark Gray /I35 at 0.118 inch (3 mm), ASTM D1003: 18 percent.

d. Water Absorption at 24 hours, ASTM D570: 0.15 percent.e. Poisson's Ratio, ASTM E132: 0.38.f. Impact Resistance, ASTM D3763: 46.



j. Instrumented Impact, ASTM D3763 at 0.125 inch (3 mm): 46 ft lbs (62.37 Nm).k. Shear Strength, Ultimate, ASTM D732: 10,000 psi (68947 kPa).l. Shear Strength, Yield, ASTM D732: 6,000 psi (41368 kPa).m. Shear Modulus, ASTM D732: 114,000 psi (7860002 kPa).n. Rockwell Hardness, ASTM D785: M70 and R118.




F (132 degrees C). At 66 psi (455 kPa): 280 degrees F (138 degrees C).d. Brittleness Temperature, ASTM D746: Minus 200 degrees F (minus 129

degrees C).e. Shading Coefficient, NFRC 100 at 0.236 inch (6 mm) Thick: Clear; 0.97. Gray

or Bronze; 0.77.f. U factor, NFRC 100 at 0.236 inch (6 mm):

1) Summer: 0.85 BTU/hr/sq ft/degrees F (4.82 W/sq m/degrees C).2) Winter: 0.92 BTU/hr/sq ft/degrees F (5.22 W/sq m/degrees C).

g. U factor, NFRC 100 at 0.375 inch (9.5 mm):1) Summer: 0.78 BTU/hr/sq ft/degrees F (4.43 W/sq m/degrees C).2) Winter: 0.85 BTU/hr/sq ft/degrees F (4.82 W/sq m/degrees C).

08 84 00-18

6. Tuffack Polycarbonate, Makrolon Sign Matte. Clear polycarbonate, for sign faces.7. Limited Product Warranty: Five year against breakage.8. Physical Properties:

a. Specific Gravity ASTM D792: 1.2.b. Refractive Index, ASTM D542 at 72 degrees F (22.2 degrees C): 1.586.c. Light Transmission, ASTM D1003, Clear 1/8 inch (3 mm): 86 percent.d. Light Transmission, ASTM D1003, Gray/Bronze: 50 percent.e. Light Transmission, ASTM D1003, Dark Gray: 18 percent.f. Rockwell Hardness, ASTM D785: M70 and R118.g. Water Absorption, Equilibrium after 24 hrs, ASTM D570: 0.15 percent.h. Surface Finish: Polished or Matte.

9. Mechanical Properties:a. Tensile Strength, Ultimate, ASTM D638: 9,500 psi (65500 kPa).b. Tensile Strength, Yield, ASTM D638: 9,000 psi (62053 kPa).c. Tensile Modulus, ASTM D638: 345,000 psi (2378691 kPa).d. Flexural Strength, ASTM D790: 13,500 psi (93079 kPa).e. Flexural Modulus, ASTM D790: 345,000 psi (2378691 kPa).f. Compressive Strength, ASTM D695: 12,500 psi (86184 kPa).g. Compressive Modulus, ASTM D695: 345,000 psi (2378691 kPa).h. Elongation, ASTM D638: 110 percent.i. Poisson's Ratio: 0.38.j. Izod Impact Strength, ASTM D256 at 1/8 inch (3 mm):


k. Instrumented Impact, ASTM D3763 at 1/8 inch (3 mm): 45 ft lbs (61.01 Nm).l. Shear Strength, Ultimate, ASTM D732: 10,000 psi (68947 kPa).m. Shear Strength, Yield, ASTM D732: 6,000 psi (41368 kPa).n. Shear Modulus, ASTM D732: 114,000 psi (7860002 kPa).


degrees Fb. Coefficient of Thermal Conductivity, ASTM C177: 1.35 BTU/hr/sq ft/degrees F



degrees C).e. Shading Coefficient, ASHRAE at 1/8 inch (3 mm): Clear: 1.02. Gray: 0.7.

Bronze: 0.7.f. U Value at 1/4 inch (6 mm) thick: Summer Gain: 0.90. Winter Loss: 0.96.

11. Electrical Properties:a. Dielectric Constant, ASTM D150 at 10 Hz: 2.96. At 60 Hz: 3.17.b. Volume Resistivity, ASTM D257: 8.2 x 10E16 Ohm cm.c. Dissipation Factor, ASTM D150 at 60 Hz: 0.0009. At 1 MHz: 0.01.d. Arc Resistance, ASTM D495: Stainless Steel Strip electrode: 10 to 11 seconds.

Tungsten Electrodes: 120 seconds.e. Dielectric Strength, ASTM D149 in air at .125 inch (3 mm): 380 V/mil.

12. Flammability:a. Horizontal Burn, AEB, ASTM D635: Less than 1 inch (25 mm).b. Ignition Temperature, ASTM D1929: Self: 1070 degrees F (576.7 degrees C).

Flash: 870 degrees F (456.5 degrees C).c. Flame Class, UL 94 at 0.060 inch (1.52 mm): V2. At 0.236 (6 mm): V0.

O. Tuffack Polycarbonate, Makrolon SL sheet. Sign Grade sheet is a lightweight thermoformable polycarbonate sheet or reel product with advanced UV resistance. High clarity, long lasting weathering performance, high impact strength, dimensionally stabile, and

08 84 00-19

high temperature resistance.1. Standards Compliance: CID A-A-59502. Type IV, Coated Sheet with UV Resistance,

Class 1 - Monolithic. UL 879 standard for electric sign components.2. Color: Clear.3. Color: As determined by the Architect.4. Limited Product Warranty: 10 year for breakage resistance.5. Impact Resistance, ASTM D3763: 46.6. Physical Properties:

a. Specific Gravity, ASTM D792: 1.2.b. Refractive Index, ASTM D542: 1.586.c. Light Transmission, ASTM D1003:

1) At 0.118 inch (3 mm): Clear: 86 percent. B59 White: 27 percent.2) At 0.150 and 0.177 inch (3.81 and 4.48 mm): B54 White: 27 percent.

d. Water Absorption, Equilibrium, at 24 hours, ASTM D570: 0.15 percent.e. Poisson's Ratio, ASTM E132: 0.38.f. Color: Clear/ A00: 0.093 to 0.236 inches (2.36 to 6.00 mm).g. Color: White/ B59: 0.093 to 0.118 inches (2.36 to 3.00 mm).h. Color: White/ B54: 0.150 to 0.236 inches (3.81 to 6.00 mm).i. Color: Red/ D92: 0.118 to 0.177 inches (3.00 to 4.50 mm.



j. Instrumented Impact, ASTM D3763 at 0.125 inch (3 mm): 46 ft lbs (62.37 Nm).k. Shear Strength, Ultimate, ASTM D732: 10,000 psi (68947 kPa).l. Shear Strength, Yield, ASTM D732: 6,000 psi (41368 kPa).m. Shear Modulus, ASTM D732: 114,000 psi (7860002 kPa).n. Rockwell Hardness, ASTM D785: M70 and R118.






a. Dielectric Constant, ASTM D150 at 10 Hz: 2.96. At 60 Hz: 3.17.b. Volume Resistivity ASTM D257 Ohm-cm 8.2 x 1016.c. Dissipation Factor, ASTM D150 at 60 Hz: 0.0009.d. Arc Resistance, ASTM D495: Stainless Steel Strip electrode: 10 seconds.

Tungsten Electrodes: 120 seconds.e. Dielectric Strength, ASTM D149 in air at 0.125 inch (3 mm): 380 V/mil

10. Flammability:a. Horizontal Burn, AEB, ASTM D635: Less than 1 inch 9(25 mm).b. Flame Class, UL 94 at 0.060 inch (1.5 mm): HB.c. Ignition Temperature, ASTM D1929: Self: 1022 degrees F (550 degrees C).

08 84 00-20

Flash: 824 degrees F (440 degrees C).

P. Tuffack Polycarbonate, Makrolon WG sheet. High impact strength, elasticity modulus, and dimensional stability. Good mechanical and electrical properties. Low levels of impurities.1. Standards Compliance: CID A-A-59502. Type 1, Class 1, UV Stabilized.2. Physical Properties:

a. Specific Gravity, ASTM D792: 1.2.b. Water Absorption after 24 hrs, ASTM D570: 0.15 percent.c. Poisson's Ratio, ASTM E132: 0.38.

3. Mechanical Properties:a. Tensile Strength, Ultimate, ASTM D638: 9,500 psi (65500 kPa).b. Tensile Strength, Yield, ASTM D638: 9,000 psi (62053 kPa).c. Tensile Modulus, ASTM D638: 340,000 psi (2344217 kPa).d. Elongation, ASTM D638: 110 percent.e. Flexural Strength, ASTM D790: 13,500 psi (93079 kPa).f. Flexural Modulus, ASTM D790: 345,000 psi (2378691 kPa).g. Compressive Strength, ASTM D695: 12,500 psi (86184 kPa).h. Compressive Modulus, ASTM D695: 345,000 psi (2378691 kPa).i. Shear Strength at Yield, ASTM D732: 6,000 psi (41368 kPa).j. Shear Strength, Ultimate, ASTM D732: 10,000 psi (638948 kPa).k. Shear Modulus, ASTM D732: 114,000 psi (786002 kPa).l. Rockwell Hardness, ASTM D785: M70, and R118.




F. At 66 psi (455 kPa): 280 degrees F.d. Brittleness Temperature, ASTM D746: Minus 200 degrees F (minus 129


a. Dielectric Constant at 10 Hz ASTM D150: 2.96.b. Dielectric Constant at 60 Hz ASTM D150: 3.17.c. Volume Resistivity ASTM D257: 8.2 x 1016Ohm cm.d. Dissipation Factor at 60 Hz, ASTM D150: 0.e. Dielectric Strength, in air at 0.125 inch (3 mm), ASTM D149: 380 V/mil.

6. Optical Properties: Haze, ASTM D1746: 1.0 percent.7. Flammability Properties:

a. Flame Class, UL 94 at 0.75 to 2.00 inch (19 to 51 mm): VO.8. Tuffack Polycarbonate, Makrolon VR rollable sheet. High optical quality, exceptional

durability, weathering, and UV resistant. Low optical distortion. Cut and sewn seams. A high clarity, wrinkle-free alternative to flexible vinyl. Impact strength maintained to minus 30 degrees F (minus 43.4 degrees C).

9. Limited Product Warranty: 5 year against breakage.10. Physical Properties:

a. Specific Gravity, ASTM D 792: 1.2.b. Light Transmission, ASTM D1003, at 0.040 inch (1 mm) thick, Clear: 90

percent.c. Impact Resistance, ASTM D3763: 47 ft-lbs (63.7 Nm).

11. Mechanical Properties:a. Izod Impact Strength, ASTM D256 at 1/8 inch (3 mm):


b. Instrumented Impact, ASTM D3763 at 0.125 inch (3 mm): 47 ft lbs (63.72 Nm).c. Instrumented Impact at 0.125 inch (3 mm) at minus 30 degrees F (minus 34.4

08 84 00-21

degrees C), ASTM D3763: 50 ft lbs (67.8 Nm).d. Poisson's Ratio ASTM E132: 0.38.e. Rockwell Hardness ASTM D785: M70 and R118.


degrees F.b. Heat Deflection Temperature, ASTM D648: At 264 psi (1820 kPa): 270 degrees

F (132 degrees C). At 66 psi (455 kPa): 280 degrees F (138 degrees C).

2.4 MULTIWALL POLYCARBONATE SHEETS

A. Basis of Design: Gallina Multiwall Polycarbonate.1. Two-Wall Systems: PolyCarb as supplied by A and C Plastics.

a. Thickness: 5/32 inch (4 mm). Weight: 0.164 lbs per sq ft (0.80 kg per sq m).1) Standards Compliance: ASTM E84 Class A.2) Bend Radius, Minimum: 30 inches (762 mm).3) U-Value: 0.68.4) Clear: Visible Light Transmission: 85.

a) Solar Heat Gain Coefficient: 0.83.b) Shading Coefficient: 0.95.

5) Bronze: Visible Light Transmission: 57.a) Solar Heat Gain Coefficient: 0.66.b) Shading Coefficient: 0.76.

6) Opal: Visible Light Transmission: 58.a) Solar Heat Gain Coefficient: 0.66.b) Shading Coefficient: 0.76.

b. Thickness: 1/4 inch (6 mm). Weight: 0.266 lbs per sq ft (1.30 kg per sq m).1) Standards Compliance: ASTM E84 Class A, ASTM D635 Class CCI.2) Bend Radius, Minimum: 39 inches (991 mm).3) U-Value: 0.61.4) Clear: Visible Light Transmission: 80.




7) Blue: Visible Light Transmission: 53.a) Solar Heat Gain Coefficient: 0.66.b) Shading Coefficient: 0.76.

8) Green: Visible Light Transmission: 54.a) Solar Heat Gain Coefficient: 0.66.b) Shading Coefficient: 0.76.

c. Thickness: 5/16 inch (8 mm). Weight: 0.307 lbs per sq ft (1.50 kg per sq m).1) Standards Compliance: ASTM E84 Class A, ASTM D635 Class CCI.2) Bend Radius, Minimum: 59 inches (1499 mm).3) U-Value: 0.58.4) Clear: Visible Light Transmission: 81.

a) Solar Heat Gain Coefficient 0.82.b) Shading Coefficient: 0.94.


6) Opal: Visible Light Transmission: 57.

08 84 00-22




d. Thickness: 3/8 inch (10 mm). Weight: 0.348 lbs per sq ft (1.70 kg per sq m).1) Standards Compliance: ASTM E84 Class A, ASTM D635 Class CCI.2) Bend Radius, Minimum: 69 inches (1753 mm).3) U-Value: 0.52.4) Clear: Visible Light Transmission: 82.





8) Green: Visible Light Transmission: .54.a) Solar Heat Gain Coefficient: 0.80.b) Shading Coefficient: 0.80.

2. Three-Wall Systems: PolyCarb as supplied by A and C Plastics.a. Thickness: 5/16 inch (8 mm). Weight: 0.348 lbs per sq ft (1.70 kg per sq m).

1) Bend Radius, Minimum: 69 inches (1753 mm).2) U-Value: 0.52.3) Clear: Visible Light Transmission: 76.


b. Thickness: 3/8 inch (10 mm). Weight: 0.430 lbs per sq ft (2.10 kg per sq ft).1) Bend Radius, Minimum: 79 inches (2007 mm).2) U-Value: 0.47.3) Clear: Visible Light Transmission: 74.

a) Solar Heat Gain Coefficient: 075.b) Shading Coefficient: 0.86.



c. Thickness: 5/8 inch (16 mm). Weight: 0.553 lbs per sq ft (2.70 kg per sq m).1) Standards Compliance: ASTM E84 Class A.2) Bend Radius, Minimum: 110 inches (2794 mm).3) U-Value: 0.40.4) Clear: Visible Light Transmission: 74.



08 84 00-23




d. Thickness: 1 inch (25 mm). Weight: 0.665 lbs per sq ft (3.25 kg per sq m).1) Standards Compliance: ASTM E84 Class A.2) Bend Radius, Minimum: 158 inches (4013 mm).3) U-Value: 0.34.4) Clear: Visible Light Transmission: 72.


5) Bronze: Visible Light Transmission: 35.6) Opal: Visible Light Transmission: 35.


3. Five-Wall RDC Systems: PolyCarb as supplied by A and C Plastics.a. Thickness: 5/8 inch (16 mm). Weight: 0.533 lbs per sq ft (2.60 kg per sq m).

1) Standards Compliance: ASTM E84 Class A, ASTM D635 Class CC1.2) Bend Radius, Minimum: 138 inches (3505 mm).3) U-Value: 0.36.4) Clear: Visible Light Transmission: 65.




4. Six-Wall Systems: PolyCarb as supplied by A and C Plastics.a. Thickness: 5/8 inch (16 mm). Weight: 0.574 lbs per sq ft (2.80 kg per sq m).

1) Bend Radius, Minimum: 110 inches (2794 mm).2) U-Value: 0.32.3) Clear: Visible Light Transmission: 60.



5. Seven-Wall Systems: PolyCarb as supplied by A and C Plastics.a. Thickness: 1 inch (25 mm). Weight: 0.717 lbs per sq ft (3.50 kg per sq m).

1) Standards Compliance: ASTM E84 Class A, ASTM D635 Class CC1.2) Bend Radius: Do not bend.3) U-Value: 0.26.4) Clear: Visible Light Transmission: 58.



b. Thickness: 1-9/16 inch (40 mm). Weight: 0.799 lbs per sq ft (3.90 kg per sq m).

08 84 00-24

1) Standards Compliance: ASTM D635 Class CC1.2) Bend Radius: Do not bend.3) U-Value: 0.19.4) Clear: Visible Light Transmission: 55.



6. Eleven-Wall Systems: PolyCarb as supplied by A and C Plastics.a. Thickness: 1 inch (25 mm) Weight: 0.696 lbs per sq ft (3.40 kg per sq m).

1) Standards Compliance: ASTM D635 Class CC1.2) Bend Radius: Do not bend.3) U-Value: 0.23.4) Clear: Visible Light Transmission: 45.



b. Thickness: 1-1/4 inch (32 mm). Weight: 0.758 lbs per sq ft (3.70 kg per sq m).1) Standards Compliance: ASTM D635 Class CC1.2) Bend Radius: Do not bend.3) U-Value: 0.19.4) Clear: Visible Light Transmission: 44.



7. PolyCarb Accessories:a. PC Corner R Profile: 5/16, 3/8, 5/8 inch (8, 10, 16 mm).b. PC Corner F Profile: 5/16, 3/8, 5/8 inch (8, 10, 16 mm).c. PC Connector H Profile: 5/16, 3/8, 5/8, 3/4, 1 inch (8, 10, 16, 20, 25 mm).d. Aluminum U Profile: 5/16, 3/8, 5/8 inch (8, 10, 16 mm).e. PC U Profile: 5/16, 3/8, 5/8, 1 inch (8, 10, 16, 25 mm).f. PC Snap H Connector Profile: 7/32, 3/8 (6, 10 mm).g. Washers with gaskets. Bubble washers. Neoprene washers.

B. Basis of Design: ArcoPlus Modular Systems as supplied by A and C Plastics.1. Optional Treatments:

a. Coating: IR. Reducing the interior solar heat gain coefficient by 20 percent.b. Coating: UV. 1-sided. Protection with a matte finish.c. Coating: UV. 2-sided. Protection with a matte finish.d. Color: As determined by the Architect.e. Three-Wall Modular System No. 613. Thickness: 0.394 inches (10 mm). Width:

23.82 inch (605 mm).f. Bend Radius, Minimum: Do not bend.g. Weight: 0.348 lbs per sq ft (1.7 kg per sq m).h. U-Factor: 0.475.i. UV Protection: None.j. Clear: Visible Light Transmission: 76.

1) Solar Heat Gain Coefficient: 0.81.k. Opal: Visible Light Transmission: 58.

1) Solar Heat Gain Coefficient: 0.65.2. Four-Wall Modular System No. 324:

08 84 00-25

a. Standards Compliance: ASTM E84 Class B, ASTM D635 Class CC1.b. Thickness: 0.787 inches (20 mm). Width: 13.11 inch (333 mm).c. Bend Radius, Minimum: Do not bend.d. Weight: 0.512 lbs per sq ft (2.5 kg per sq m).e. U-Factor: 0.32.f. UV Protection: 1 side.g. Clear: Visible Light Transmission: 70.

1) Solar Heat Gain Coefficient: 0.74.h. Opal: Visible Light Transmission: 45.

1) Solar Heat Gain Coefficient: 0.50.i. Bronze: Visible Light Transmission: 60.

1) Solar Heat Gain Coefficient: 0.67.j. Green: Visible Light Transmission: 65.

1) Solar Heat Gain Coefficient: 0.70.k. Accessories: Multiwall tongue and groove system for windows and walls.

1) Aluminum Upper/Side Profile: No. 4061.2) Aluminum Base Profile: No. 4062.3) Stainless Steel Bracket: No. 4063.4) Aluminum Base Profile with Eave: No. 4064.5) External Frame Gasket: No. 1169/B.

3. Seven-Wall Modular System No. 547:a. Standards Compliance: ASTM E84 Class A, ASTM D635 Class CC1.b. Thickness: 1.574 inches (40 mm). Width: 19.68 inch (424 mm).c. Bend Radius, Minimum: Do not bend.d. Weight: 0.817 lbs per sq ft (3.99 kg per sq m).e. U-Factor: .188 to .28.f. UV Protection: None.g. Clear: Visible Light Transmission: 70.



1) Solar Heat Gain Coefficient: 0.47.j. Green: Visible Light Transmission: 60.

1) Solar Heat Gain Coefficient: 0.65.k. Accessories: Tongue and groove modular system for windows and walls.

1) Aluminum Base Profile: No. 4140.2) Aluminum Upper/Side Profile No. 4045.3) Aluminum Base Profile with Eave: No. 4046.4) Aluminum Base Profile: No. 4047.5) Aluminum Bracket 60/120 mm: No. 4050.6) Aluminum Upper / Side Profile TB: No. 4585.7) Aluminum Base Profile TB: No. 4587.8) Base Profile with Eave: No. 4590.9) Base Profile with Eave TB: No. 4595.10) Aluminum Perimeter Profile: No. 4597.11) External Frame Gasket: No. 1169/B.

4. Four-Wall Modular System No. 684:a. Standards Compliance: ASTM E84 Class A.b. Thickness: 0.315 inch (8 mm). Width: 23.62 (600 mm).c. Bend Radius, Minimum: 6.56 ft (2000 mm).d. Weight: 0.40 lbs per sq ft (1.95 kg per sq m).e. U-Factor: 0.400.f. UV Protection: 2 sided.g. Clear: Visible Light Transmission: 70.

1) Solar Heat Gain Coefficient: 0.71.

08 84 00-26

h. Opal: Visible Light Transmission: 42.1) Solar Heat Gain Coefficient: 0.55.

i. Bronze: Visible Light Transmission: 45.1) Solar Heat Gain Coefficient: 0.50.

j. Accessories: For framing vertical walls and windows. Lengths: Unlimited.1) PC Connector Cover Gasket: No. 2146.2) Upper / Side Aluminum Profile: 4045.3) Flat Fastening Bracket 5/16 inch (8 mm): No. 4138.4) Aluminum Base/Side Profile with Flap: No. 4140.5) LDPE Foam Pad: No. 4213.6) LDPE Foam Pad: No. 4221.7) Aluminum Connector Profile: No. 4243.8) Aluminum Connector End Profile: No. 4244.9) Aluminum U-Frame: No. 4245.10) Aluminum U-Frame Support: No. 4252.11) E-Clips for 4243 and 4244: No. 4260.12) Side Mounting Bracket: No. 4264.13) PC Cap for 2146: No. 4303.14) Aluminum Connector Cover Gasket: No. 4310.15) LDPE Foam Connector: No. 4318.16) Aluminum Joining Connector: No. 4319.17) Extruded Bracket.18) PC Starter Profile.19) PC Terminal Profile.20) Aluminum block cover.

5. Four-Wall Modular System No. 6104:a. Thickness: 0.394 inch (10 mm). Width: 23.62 (600 mm).b. Bend Radius, Minimum: 8 ft (2438 mm).c. Weight: 0.451 lbs per sq ft (2.20 kg per sq m).d. U-Factor: 0.44.e. UV Protection: 2 sided.f. Clear: Visible Light Transmission: 70.

1) Solar Heat Gain Coefficient: 0.70.g. Opal: Visible Light Transmission: 38.

1) Solar Heat Gain Coefficient: 0.53.h. Bronze: Visible Light Transmission: 45.

1) Solar Heat Gain Coefficient: 0.50.i. Accessories: For framing vertical walls and windows. Lengths: Unlimited.

1) PC Connector Cover Gasket: No. 2146.2) Upper / Side Aluminum Profile: 4045.3) Flat Fastening Bracket 5/16 inch (8 mm): No. 4138.4) Aluminum Base/Side Profile with Flap: No. 4140.5) LDPE Foam Pad: No. 4213.6) LDPE Foam Pad: No. 4221.7) Aluminum Connector Profile: No. 4243.8) Aluminum Connector End Profile: No. 4244.9) Aluminum U-Frame: No. 4245.10) Aluminum U-Frame Support: No. 4252.11) E-Clips for 4243 and 4244: No. 4260.12) Side Mounting Bracket: No. 4264.13) PC Cap for 2146: No. 4303.14) Aluminum Connector Cover Gasket: No. 4310.15) LDPE Foam Connector: No. 4318.16) Aluminum Joining Connector: No. 4319.17) Extruded Bracket.18) PC Starter Profile.

08 84 00-27

19) PC Terminal Profile.20) Aluminum block cover.

6. Four-Wall Modular System No. 6124:a. Standards Compliance: ASTM E84 Class A.b. Thickness: 0.472 inches (12 mm). Width: 23.62 (600 mm).c. Bend Radius, Minimum: 8.2 ft (2500 mm).d. Weight: 0.502 lbs per sq ft (2.45 kg per sq m).e. U-Factor: 0.40.f. UV Protection 2 sided.g. Clear: Visible Light Transmission: 68.



1) Solar Heat Gain Coefficient: 0.50.j. Accessories: For framing vertical walls and windows. Lengths: Unlimited.

1) PC Connector Cover Gasket: No. 2146.2) Upper / Side Aluminum Profile: 4045.3) Flat Fastening Bracket 5/16 inch (8 mm): No. 4138.4) Aluminum Base/Side Profile with Flap: No. 4140.5) LDPE Foam Pad: No. 4213.6) LDPE Foam Pad: No. 4221.7) Aluminum Connector Profile: No. 4243.8) Aluminum Connector End Profile: No. 4244.9) Aluminum U-Frame: No. 4245.10) Aluminum U-Frame Support: No. 4252.11) E-Clips for 4243 and 4244: No. 4260.12) Side Mounting Bracket: No. 4264.13) PC Cap for 2146: No. 4303.14) Aluminum Connector Cover Gasket: No. 4310.15) LDPE Foam Connector: No. 4318.16) Aluminum Joining Connector: No. 4319.17) Extruded Bracket.18) PC Starter Profile.19) PC Terminal Profile.20) Aluminum block cover.

7. Six-Wall Modular System No. 6166:a. Thickness: 0.630 inches(16 mm). Width: 23.62 inch (600 mm).b. Bend Radius, Minimum: 9.5 ft (2896 mm).c. Weight: 0.614 lbs per sq ft (3 kg per sq m).d. U-Factor: 0.32.e. UV Protection: 2 sided.f. Clear: Visible Light Transmission: 59.

1) Solar Heat Gain Coefficient: 0.63.g. Opal: Visible Light Transmission: 34.

1) Solar Heat Gain Coefficient: 0.49.h. Bronze: Visible Light Transmission: 41.

1) Solar Heat Gain Coefficient: 0.46.i. Accessories: For framing vertical walls and windows. Lengths: Unlimited.

1) PC Connector Cover Gasket: No. 2146.2) Upper / Side Aluminum Profile: 4045.3) Flat Fastening Bracket 5/16 inch (8 mm): No. 4138.4) Aluminum Base/Side Profile with Flap: No. 4140.5) LDPE Foam Pad: No. 4213.6) LDPE Foam Pad: No. 4221.7) Aluminum Connector Profile: No. 4243.

08 84 00-28

8) Aluminum Connector End Profile: No. 4244.9) Aluminum U-Frame: No. 4245.10) Aluminum U-Frame Support: No. 4252.11) E-Clips for 4243 and 4244: No. 4260.12) Side Mounting Bracket: No. 4264.13) PC Cap for 2146: No. 4303..14) Aluminum Connector Cover Gasket: No. 431015) LDPE Foam Connector: No. 4318.16) Aluminum Joining Connector: No. 4319.17) Extruded Bracket.18) PC Starter Profile.19) PC Terminal Profile.20) Aluminum block cover.

8. Six-Wall Modular System No. 626:a. Standards Compliance: ASTM E84 Class A, ASTM D635 Class CC1.b. Thickness: 0.787 inches (20 mm). Width: 23.62 inch (600 mm).c. Bend Radius, Minimum: 13 ft (3962 mm).d. Weight: 0.655 lbs per sq ft (3.20 kg per sq m).e. U-Factor: 0.264.f. UV Protection: 2 sided.g. Clear: Visible Light Transmission: 58. Solar Heat Gain Coefficient: 0.62.h. Opal: Visible Light Transmission: 33. Solar Heat Gain Coefficient: 0.48.i. Bronze: Visible Light Transmission: 40. Solar Heat Gain Coefficient: 0.45.j. Green: Visible Light Transmission: 48. Solar Heat Gain Coefficient: 0.53.k. Accessories: For framing vertical walls and windows. Lengths: Unlimited.

1) Connector Cover Gasket: No. 2146.2) PC Starter Profile: No. 2179.3) PC Terminal Profile: No. 2180.4) Corner 90 degree Cover Profile: No. 2550.5) LDPE Foam Pad: No. 4213.6) Aluminum Connector Profile: No. 4243.7) Aluminum Connector End Profile: No. 4244.8) Aluminum U-Frame: No. 4245.9) Aluminum U-Frame Support: No. 4252.10) E-Clips for 4243 and 4244: No. 4260.11) Flat Fastening Bracket: No. 4263.12) Side Mounting Bracket: No. 4264.13) Base/Side Profile with Flap: No. 4271.14) PC Cap for 2146: No. 4303.15) Aluminum Cover Gasket: No. 4310.16) Aluminum Connector Cover Gasket: No. 4310.17) LDPE Foam Connector: No. 4318.18) Aluminum Joining Connector: No. 4319.19) Extruded Bracket: No. 4328.20) Side Mounting Bracket: No. 4328.21) Aluminum Corner Profile: No. 4588.22) Aluminum block cover.23) PC block cover.

C. Basis of Design: Solid Polycarbonate Sheets:1. Sheet Type: PolyComp. 2 side UV protection for architectural applications.2. Sheet Type: Scudo No UV protection for industrial applications.3. Physical, Mechanical, and Thermal Properties:

a. Density, ISO 1183/B: 74.91 lbs per sq ft (1,200 kg per cu m).b. Melt Mass Flow Rate, ISO 1133: (3.0 grams per 10 min).c. Water Absorption, ISO 62-4:

08 84 00-29

1) At 73 Degrees F (23 Degrees C): 0.15 percent.2) For 24 Hours at 73 Degrees F (23 Degrees C) at 50 Percent Relative

Humidity: 0.32 percent.d. Refraction Index ISO 489: 1,586.e. Tensile Modulus ISO 527-2/50: (2350 MPa).f. Tensile Strength Yield, ISO 527-2/50: (60.0 MPa).g. Tensile Strength Break, ISO 527-2/50: (72.0 MPa).h. Tensile Elongation, ISO 527-2/50: 150 percent.i. Flexural Modulus, ISO 178: (2300 MPa).j. Flexural Strength, ISO 178: (90 MPa).k. Taber Abrasion Resistance, ASTM D1044: 45 percent.

4. Impact, Notched Izod, ASTM D256.5. Impact, Notched Izod, ISO 180/A.6. Softening Temperature, ISO 306: 295 to 304 degrees F (146 to 151 degrees C).7. Thermal Conductivity, ISO 8302: 1155.58 BTU per hr ft degrees F (0.2 W per m

degrees C).8. Linear Thermal Expansion ISO 11359-2: 0.001 inch per ft per degrees F (0.065 mm

per m per degrees C).9. Flammability Properties:

a. Flame Rating, UL 94: At 0.062 (1.60 mm) and 0.125 (3.20 mm): HB.b. Oxygen Index, ISO 4589-2: 26 percent.c. Average Extent of Burning, ASTM D635: 1.18 inches (30 mm).

10. Sheet Thickness: 0.093 inch (2 mm). Bend Radius: 11.81 inches (300 mm).a. U-Value, ISO 10077-2: 0.99.b. Sound Insulation Rw, ISO 717-1: 25 dB.c. Light Transmission, EN 14500: 91 percent.

11. Sheet Thickness: 0.118 inch (3 mm): Bend Radius: 17.72 inches (450 mm).a. U-Value, ISO 10077-2: 095.b. Sound Insulation Rw, ISO 717-1: 26 dB.c. Light Transmission, EN 14500: 90 percent.d. Sheet Thickness: 0.157 inch (4 mm). Bend Radius: 23.62 inches (600 mm).U-

Value, ISO 10077-2: 0.93.e. Sound Insulation Rw, ISO 717-1: 27 dB.f. Light Transmission, EN 14500: 90 percent.

12. Sheet Thickness: 0.197 inch (5 mm). Bend Radius: 29.53 inches (750 mm).a. U-Value, ISO 10077-2: 0.90.b. Sound Insulation Rw, ISO 717-1 dB: 28 dB.c. Light Transmission (LT percent), EN 14500: 89 percent.




16. Sheet Thickness: 0.472 inch (12 mm). Bend Radius: 66.93 inches (1700 mm).a. U-Value, ISO 10077-2: 0.76.b. Sound Insulation Rw, ISO 717-1: 34 db.c. Light Transmission, EN 14500: 80 percent.

D. Framing Systems:

08 84 00-30

1. Basis of Design: Poli-Lok Aluminum Framing System. High quality weather resistant aluminum extrusion with seamless finish and concealed screw covers.a. Electrical Properties:

1) Volume Electrical Resistivity IEC 60093: 2x10E17 Ohm cm.2) Dielectric Strength, ASTM D149, 420 V per mil: 17 kV per mil.3) Dielectric Strength, IEC 60243-1 430 V per mil: 17 kV per mil.4) Dielectric Constant, ASTM D150 at 60 Hz: 3.00.5) Dielectric Constant, ASTM D150 at 1 MHz: 3.00.6) Dissipation Factor, ASTM D150 at 60 Hz: 0.001.7) Dissipation factor, ASTM D150 at 1 MHz: 0.002.

PART 3 EXECUTION

3.1 EXAMINATION

A. Do not begin installation until substrates have been properly constructed and prepared.

B. If substrate preparation is the responsibility of another installer, notify Architect in writing of unsatisfactory preparation before proceeding.

3.2 PREPARATION

A. Prepare surfaces using the methods recommended by the manufacturer for achieving the best result for the substrate under the project conditions.

3.3 INSTALLATION

A. Install in accordance with manufacturer's instructions approved submittals and in proper relationship with adjacent construction.

3.4 FIELD QUALITY CONTROL

A. Field Inspection: Coordinate field inspection in accordance with appropriate sections in Division 01.

3.5 CLEANING AND PROTECTION

A. Clean products in accordance with the manufacturers recommendations. Replace damaged products before Substantial Completion.

END OF SECTION

08 84 00-31

Date post:	25-Apr-2020
Category:	Documents
Upload:	others
View:	42 times
Download:	5 times

· Web viewASTM D792 - For Density and Specific Gravity (Relative Density) of Plastics by...

Documents