· Web viewSECTION 14 20 10. NON-PROPRIETARY PASSENGER ELEVATOR EQUIPMENT. Display hidden notes...

SECTION 14 20 10NON-PROPRIETARY PASSENGER ELEVATOR EQUIPMENT

Display hidden notes to specifier. (Don't know how? Click Here)

Copyright 2019 - 2019 ARCAT, Inc. - All rights reserved

1 GENERAL

1.1 SECTION INCLUDES

1.1.1 Fixtures: (GAL)1.1.1.1 Pre-engineered car stations.1.1.1.2 Pre-engineered hall stations.1.1.1.3 Extender hall stations.1.1.1.4 Position indicators and lanterns.1.1.1.5 Additional equipment.

1.1.2 Door Equipment: (GAL)1.1.2.1 Operators.1.1.2.2 Car door hangers.1.1.2.3 Clutches1.1.2.4 Door protection.1.1.2.5 Hatch door hangers.1.1.2.6 Interlocks.1.1.2.7 Closers.1.1.2.8 Switches and Contacts.1.1.2.9 Fault Monitors.

1.1.3 Elevator Hoisting Equipment: (Hollister and Whitney)1.1.3.1 Overhead traction machines1.1.3.2 Basement set traction machines.1.1.3.3 Overhead deflector machines.1.1.3.4 Gearless machines.1.1.3.5 Rope grippers.1.1.3.6 Sheaves.1.1.3.7 Roller guide shoes.1.1.3.8 Rigid and swivel shoes.1.1.3.9 Disk and drum brakes.1.1.3.10 Safeties.1.1.3.11 Overspeed governors and tension weights.1.1.3.12 Car slings and platforms.1.1.3.13 Counterweight frames.1.1.3.14 Spring and oil buffers.1.1.3.15 Elevator equipment accessories.1.1.3.16 VIV motors for geared machines.1.1.3.17 MRL elevators.1.1.3.18 Equipment guarding.1.1.3.19 Compensating rope tension sheaves.

14 20 10-1

1.1.4 Hydraulic Elevator Components: (Bore-Max Corporation)1.1.4.1 Hydraulic jacks.1.1.4.2 Pump units:

1.1.4.2.1 Submersible.1.1.4.2.2 Dry/belt driven.

1.1.4.3 Slings and platform packages.

1.1.5 Control Systems:1.1.5.1 Control system. (Elevator Controls)1.1.5.2 Traveling cable. (Elevator Controls)1.1.5.3 Monitoring. (Elevator Controls)1.1.5.4 Controllers. (GAL)1.1.5.5 Safety controls. (GAL)1.1.5.6 Drives. (GAL)

1.2 RELATED SECTIONS

1.2.1 Section 03 30 00 - Cast-in-Place Concrete.

1.2.2 Section 06 10 00 - Rough Carpentry.

1.2.3 Section 08 11 00 - Metal Doors and Frames.

1.2.4 Section 09 23 13 - Acoustical Gypsum Plastering.

1.2.5 Section 09 60 00 - Flooring.

1.2.6 Section 14 20 00 - Elevators.

1.2.7 Division 16 - Electrical for electrical service and disconnects, wire routing and connections, telephone service.

1.3 REFERENCES

1.3.1 American Society of Mechanical Engineers (ASME):1.3.1.1 ANSI/ASME A17.1/CAN/CSA B44 - Safety Code for Elevators and Escalators.1.3.1.2 ASME A17.5 - Elevator and Escalator Electrical Equipment.

1.3.2 Canadian Standards Association (CSA).

1.3.3 European Conformity (CE).

1.3.4 European Standard (EN):1.3.4.1 EN 81 - Safety Rules for the Construction and Installation of Lifts.1.3.4.2 EN 12016 - Electromagnetic compatibility. Product family standard for lifts,

escalators and moving walks. Immunity.

1.3.5 U.S. General Services Administration (GSA).

1.3.6 Institute of Electrical and Electronics Engineers (IEEE).

1.3.7 National Electrical Manufacturers Association (NEMA).1.3.7.1 NEMA 4 - Watertight enclosure.

1.3.8 Technical Standards and Safety Authority (TSSA).

1.3.9 Underwriters Laboratories (UL).

14 20 10-2

1.4 SUBMITTALS

1.4.1 Submit under provisions of Section 01 30 00 - Administrative Requirements.

1.4.2 Product Data:1.4.2.1 Manufacturer's data sheets on each product to be used.1.4.2.2 Preparation instructions and recommendations.1.4.2.3 Storage and handling requirements and recommendations.1.4.2.4 Typical installation methods.

1.4.3 Verification Samples: Two representative units of each type, size, pattern and color.

1.4.4 Shop Drawings: Include details of materials, construction and finish. Include relationship with adjacent construction.

1.5 QUALITY ASSURANCE

1.5.1 Manufacturer Qualifications: Company specializing in manufacturing products specified in this section with a minimum five years documented experience.

1.5.2 Installer Qualifications: Company specializing in performing Work of this section with minimum two years documented experience with projects of similar scope and complexity.

1.5.3 Source Limitations: Provide each type of product from a single manufacturing source to ensure uniformity.

1.5.4 Mock-Up: Construct a mock-up with actual materials in sufficient time for Architect's review and to not delay construction progress. Locate mock-up as acceptable to Architect and provide temporary foundations and support.1.5.4.1 Intent of mock-up is to demonstrate quality of workmanship and visual

appearance.1.5.4.2 If mock-up is not acceptable, rebuild mock-up until satisfactory results are

achieved.1.5.4.3 Retain mock-up during construction as a standard for comparison with

completed work.1.5.4.4 Do not alter or remove mock-up until work is completed or removal is authorized.

1.6 PRE-INSTALLATION CONFERENCE

1.6.1 Convene a conference approximately two weeks before scheduled commencement of the Work. Attendees shall include Architect, Contractor and trades involved. Agenda shall include schedule, responsibilities, critical path items and approvals.

1.7 DELIVERY, STORAGE, AND HANDLING

1.7.1 Store and handle in strict compliance with manufacturer's written instructions and recommendations.

1.7.2 Protect from damage due to weather, excessive temperature, and construction operations.

1.8 PROJECT CONDITIONS

1.8.1 Maintain environmental conditions (temperature, humidity, and ventilation) within limits recommended by manufacturer for optimum results. Do not install products under environmental conditions outside manufacturer's recommended limits.

2 PRODUCTS

14 20 10-3

2.1 MANUFACTURERS

2.1.1 Acceptable Manufacturer: Courion, which is located at: 3044 Lambdin Ave.; St. Louis, MO 63115; Toll Free Tel: 800-533-5760; Tel: 314-533-5700; Fax: 314-533-5720; Email:request info ([email protected]); Web:http://www.couriondoors.com

2.1.2 Substitutions: Not permitted.

2.1.3 Requests for substitutions will be considered in accordance with provisions of Section 01 60 00 - Product Requirements.

2.2 FIXTURES (GAL)

2.2.1 Basis of Design: Jet II as manufactured by GAL Mfg. Company.2.2.1.1 Pre-Engineered Car Station Operating Stations:

2.2.1.1.1 Cover Material: Stainless steel. No. 4 satin finish.2.2.1.1.2 Cover Material: Muntz. No. 4 stain finish.2.2.1.1.3 Communications: GALaxy Serial Communications.2.2.1.1.4 Push Button Style: Spectral light. Multi-color 7; 24-120 V AC/DC

2.2.1.1.4.1 Model series as determined by the Architect.2.2.1.1.5 Push Button Style: LED lamp. Multi-color 7; 24-120 V AC/DC

2.2.1.1.5.1 Model series as determined by the Architect.2.2.1.1.6 California Protruding Buttons: 1/8 inch (3 mm).2.2.1.1.7 Car Station Plate Design and Size: As determined by Architect.2.2.1.1.8 Position Indicator: Digital Display:

2.2.1.1.8.1 Multi-light display with arrows.2.2.1.1.8.2 Multi-light display without arrows.2.2.1.1.8.3 Driver unit by GAL.2.2.1.1.8.4 Driver unit by others.

2.2.1.1.9 Emergency Light: Standard lens.2.2.1.1.10 Emergency Light: Flush lens.2.2.1.1.11 Audible Signal: Nudging.2.2.1.1.12 Key Switch: GAL Standard.2.2.1.1.13 Key Switch: Medeco Security cylinder.2.2.1.1.14 Lockout Floor: _____.2.2.1.1.15 Egress Floor: _____.2.2.1.1.16 Stop Switch: Key operated.2.2.1.1.17 Stop Switch: Pull to Stop.2.2.1.1.18 Fire Operation:

2.2.1.1.18.1 City and State: ________.2.2.1.1.18.2 ASME 1996, 2000, 2004, 2007, or 2010.2.2.1.1.18.3 GAL standard.2.2.1.1.18.4 Medeco.2.2.1.1.18.5 FEO-K1.2.2.1.1.18.6 Yale.

2.2.1.1.19 Telephone Location: Cover mounted.2.2.1.1.20 Telephone Location: Inside compartment.2.2.1.1.21 Telephone Type: K-Tech, building powered.2.2.1.1.22 Telephone Type: Viking, line powered.2.2.1.1.23 Engraving: To be determined by Architect.2.2.1.1.24 Hinge: As shown.2.2.1.1.25 Hinge: Opposite.

2.2.1.2 Pre-Engineered Hall Station Operating Stations2.2.1.2.1 Cover Material: Stainless steel. No. 4 satin finish.2.2.1.2.2 Cover Material: Muntz. No. 4 stain finish.2.2.1.2.3 Communications: GALaxy Serial Communications.2.2.1.2.4 Push Button Style: Spectral light. Multi-color 7; 24-120 V AC/DC

14 20 10-4

2.2.1.2.4.1 Model series as determined by the Architect.2.2.1.2.5 Push Button Style: LED lamp. Multi-color 7; 24-120 V AC/DC

2.2.1.2.5.1 Model series as determined by the Architect.2.2.1.2.6 California Protruding Buttons: 1/8 inch (3 mm).2.2.1.2.7 Hall Station Plate Design and Size: As determined by Architect.

2.2.1.2.7.1 Hall station to have lockout key switch.2.2.1.2.8 Key Switch: GAL Standard.2.2.1.2.9 Key Switch: Medeco security Cylinder2.2.1.2.10 Fire Operation:


2.2.1.3 Extender Hall Station:2.2.1.3.1 Handicap Plate: Multi-color 7, spectral light.2.2.1.3.2 Cover Material: Stainless steel. No. 4 satin finish.2.2.1.3.3 Cover Material: Muntz. No. 4 stain finish.2.2.1.3.4 Configuration: To be determined by Architect.2.2.1.3.5 Key Switch: GAL Standard.2.2.1.3.6 Key Switch: Medeco security Cylinder2.2.1.3.7 Fire Operation:


2.2.1.4 Position Indicator / Lantern:2.2.1.4.1 Cover Material: Stainless steel. No. 4 satin finish.2.2.1.4.2 Cover Material: Muntz. No. 4 stain finish.2.2.1.4.3 Position Indicator Plate Design and Size: As determined by Architect.2.2.1.4.4 Display Type:

2.2.1.4.4.1 Design: As determined by Architect.2.2.1.4.4.2 Design: _____.2.2.1.4.4.3 With arrows.2.2.1.4.4.4 Without arrows.

2.2.1.4.5 Lens Type: As determined by Architect.2.2.1.4.6 Lens Type: _____.2.2.1.4.7 LED Lamp: 24V, color to be determined by Architect.2.2.1.4.8 LED Lamp: 24V, color _____.2.2.1.4.9 LED Lamp: 120 V, color to be determined by Architect.2.2.1.4.10 LED Lamp: 120 V, color _____.2.2.1.4.11 Drive Unit: By GAL.2.2.1.4.12 Drive Unit: By others.2.2.1.4.13 Audible Signal: Chime.2.2.1.4.14 Audible Signal: Gong.

2.2.1.5 Optional Additional Equipment:2.2.1.5.1 Pit Switch: Toggle switch.2.2.1.5.2 Pit Switch: Push/pull.2.2.1.5.3 Fire Service Car Top: 24V.2.2.1.5.4 Fire Service Car Top: 120V.2.2.1.5.5 Alarm Bell.2.2.1.5.6 Apx O Sign: ASME A17.1.2.2.1.5.7 Apx O Sign: State of Maryland.

14 20 10-5

2.2.1.5.8 Apx O Sign: Florida.2.2.1.5.9 Jamb Plate.2.2.1.5.10 Surface Mount Telephone: Stainless steel.2.2.1.5.11 Surface Mount Telephone: Muntz.2.2.1.5.12 Flange Mount Telephone.2.2.1.5.13 Car Top Inspection Station: CT-10.2.2.1.5.14 Car Top Inspection Station: CT-4.2.2.1.5.15 Car Top Inspection Station: CT-6.2.2.1.5.16 Car Top Inspection Station: CT-7.2.2.1.5.17 Machine Room Communication, LC-2 Line Connector.2.2.1.5.18 SUREcom Unit with 1 Handset.2.2.1.5.19 Communication Failure Station: Chicago Cylinder.2.2.1.5.20 Communication Failure Station: Medeco Cylinder.

2.2.2 Basis of Design: B Series as manufactured by GAL Mfg. Company.2.2.2.1 Pre-Engineered Car Stations:

2.2.2.1.1 Cover Material: Stainless steel.2.2.2.1.2 Cover Material: Muntz.2.2.2.1.3 Cover Finish: Satin.2.2.2.1.4 Cover Finish: Mirrored.2.2.2.1.5 Cover Finish: Oxidized.2.2.2.1.6 Communications: GALaxy Serial Communications.2.2.2.1.7 Push Button Style: As determined by the Architect.

2.2.2.1.7.1 Illumination: Incandescent.2.2.2.1.7.2 Illumination: LED.2.2.2.1.7.3 Illumination: Neon.2.2.2.1.7.4 Illumination: GAL Spectral-Lites.

2.2.2.1.8 Car Station Plate Design and Size: As determined by Architect.2.2.2.1.9 Position Indicator: Digital display with arrows.2.2.2.1.10 Signage: Etched.2.2.2.1.11 Signage: Engraved.2.2.2.1.12 Stop Switch: Key operated.2.2.2.1.13 Stop Switch: Pull to Stop.2.2.2.1.14 Fire Operation:

2.2.2.1.14.1 City and State: ________.2.2.2.1.14.2 ASME 1996, 2000, 2004, 2007, or 2010.

2.2.2.2 Pre-Engineered Hall Stations2.2.2.2.1 Cover Material: Stainless steel.2.2.2.2.2 Cover Material: Muntz.2.2.2.2.3 Cover Finish: Satin.2.2.2.2.4 Cover Finish: Mirrored.2.2.2.2.5 Cover Finish: Oxidized.2.2.2.2.6 Push Button Style: As determined by the Architect.

2.2.2.2.6.1 Illumination: Incandescent.2.2.2.2.6.2 Illumination: LED.2.2.2.2.6.3 Illumination: Neon.2.2.2.2.6.4 Illumination: GAL Spectral-Lites.

2.2.2.2.7 Hall Station Plate Design and Size: As determined by Architect.2.2.2.2.7.1 Hall station to have lockout key switch.

2.2.2.2.8 Key Switch: GAL Standard.2.2.2.2.9 Key Switch: Medeco security Cylinder2.2.2.2.10 Fire Operation:

2.2.2.2.10.1 City and State: ________.2.2.2.2.10.2 ASME 1996, 2000, 2004, 2007, or 2010.

2.2.2.3 Position Indicators and Lanterns:2.2.2.3.1 Cover Material: Stainless steel.

14 20 10-6

2.2.2.3.2 Cover Material: Muntz.2.2.2.3.3 Cover Finish: Satin.2.2.2.3.4 Cover Finish: Mirrored.2.2.2.3.5 Cover Finish: Oxidized.2.2.2.3.6 Position Indicator Plate Design and Size: As determined by Architect.2.2.2.3.7 Display Type:

2.2.2.3.7.1 Design: As determined by Architect.2.2.2.3.7.2 Design: _____.2.2.2.3.7.3 With arrows.2.2.2.3.7.4 Without arrows.

2.2.2.3.8 Lens Type: As determined by Architect.2.2.2.3.9 Lens Type: _____.2.2.2.3.10 Illumination: Incandescent.2.2.2.3.11 Illumination: LED.2.2.2.3.12 Audible Signal: Chime.2.2.2.3.13 Audible Signal: Gong.

2.3 DOOR EQUIPMENT (GAL)

2.3.1 Operators:2.3.1.1 Basis of Design: MONXT as manufactured by GAL Mfg. Company.

2.3.1.1.1 Linear door operator.2.3.1.1.1.1 Automatic built-in smart functions.2.3.1.1.1.2 One button set-up.2.3.1.1.1.3 Integrated car door interlock.

2.3.1.1.2 Drop-in, low profile of 9 inches (229 mm).2.3.1.1.3 Maximum Panel Weight: 600 pounds (272 kg).2.3.1.1.4 Motor: Pancake, direct drive, 230V, 1/3 hp (248 Nm/s).2.3.1.1.5 Outputs: Dry contacts, serial, GAL CAN.

2.3.1.2 Basis of Design: MOVFR as manufactured by GAL Mfg. Company.2.3.1.2.1 Harmonic door operator.2.3.1.2.2 Model: Light duty.2.3.1.2.3 Model: Heavy duty.2.3.1.2.4 Features:

2.3.1.2.4.1 Closed loop regulated speed via motor performance feedback.2.3.1.2.4.2 Non-contact optical and hall effect sensors.2.3.1.2.4.3 LEDs on main board to indicate critical function status.2.3.1.2.4.4 Universal inputs.2.3.1.2.4.5 Output contact rates at 10A, 230VAC.2.3.1.2.4.6 Pluggable input modules, output relays, and connectors.2.3.1.2.4.7 Toggle switches for manual operation, diagnostics, and

operational verification.2.3.1.2.4.8 Keypad programming with LED display.2.3.1.2.4.9 Over-torque and over-speed detection and restriction limits.2.3.1.2.4.10 Controlled area network (CAN).2.3.1.2.4.11 Slow scan mode in case of DOL and DCL sensor failure.

2.3.1.2.5 Motor: 1/2 hp (373 Nm/s).2.3.1.3 Basis of Design: MOVFE 2500 - HH as manufactured by GAL Mfg. Company.

2.3.1.3.1 Heavy-duty door operator.2.3.1.3.2 Features:

2.3.1.3.2.1 Closed loop circuitry, utilizing both VVVF and encoder feedback.2.3.1.3.2.2 Non-contact optical and hall effect sensors.2.3.1.3.2.3 LEDs on main board to indicate critical function status.2.3.1.3.2.4 Toggle switches for manual testing.2.3.1.3.2.5 Keypad programming with LED display.2.3.1.3.2.6 Controlled area network (CAN).

14 20 10-7

2.3.1.3.2.7 Additional I/O board for control of narrow or heavy lobby doors.2.3.1.3.2.8 Plug and play detector edge capability2.3.1.3.2.9 Pivot points utilize precision bearings for smoother operation.2.3.1.3.2.10 Slow scan mode in case of DOL and DCL sensor failure.

2.3.1.3.3 Capacity: 1500 pounds (680 kg).2.3.1.3.4 Motor: 1/2 hp (373 Nm/s).

2.3.1.4 Basis of Design: MOVFE 2500 - HL as manufactured by GAL Mfg. Company.2.3.1.4.1 Standards Compliance:

2.3.1.4.1.1 CSA Certified.2.3.1.4.1.2 ASME A17.5.2.3.1.4.1.3 Complies with CE and IEEE safety standards.

2.3.1.4.2 Harmonic door operator.2.3.1.4.3 Model: Light duty.2.3.1.4.4 Model: Heavy duty.2.3.1.4.5 Features:

2.3.1.4.5.1 Closed loop regulated speed via motor performance feedback.2.3.1.4.5.2 Non-contact optical and hall effect sensors.2.3.1.4.5.3 LEDs on main board to indicate critical function status.2.3.1.4.5.4 Universal inputs.2.3.1.4.5.5 Output contact rates at 10A, 230VAC.2.3.1.4.5.6 Pluggable input modules, output relays, and connectors.2.3.1.4.5.7 Toggle switches for manual operation, diagnostics, and

operational verification.2.3.1.4.5.8 Keypad programming with LED display.2.3.1.4.5.9 Over-torque and over-speed detection and restriction limits.2.3.1.4.5.10 Controlled area network (CAN).2.3.1.4.5.11 Slow scan mode in case of DOL and DCL sensor failure.

2.3.1.4.6 Motor: 1/2 hp (373 Nm/s).

2.3.2 Car Door Hangers:2.3.2.1 Basis of Design: SS Single Speed as manufactured by GAL Mfg. Company.

2.3.2.1.1 Single speed car door assembly, Type A hanger. Infrared door protection.2.3.2.1.2 Left hand opening.2.3.2.1.3 Right hand opening.2.3.2.1.4 Door Size: 22 to 48 inches (559 to 1219 mm).

2.3.2.2 Basis of Design: 2S Two-Speed as manufactured by GAL Mfg Company.2.3.2.2.1 Two-speed car door assembly, Type A hanger. Infrared door protection.2.3.2.2.2 Left hand opening.2.3.2.2.3 Right hand opening.2.3.2.2.4 Door Size: 30 to 48 inches (762 to 1219 mm).

2.3.2.3 Basis of Design: 3S Three-Speed as manufactured by GAL Mfg Company.2.3.2.3.1 Three-speed car door assembly, Type A hanger. Infrared door protection.2.3.2.3.2 Left hand opening.2.3.2.3.3 Right hand opening.2.3.2.3.4 Door Size: 30 to 69 inches (762 to 1753 mm).

2.3.2.4 Basis of Design: CP Center Parting as manufactured by GAL Mfg. Company.2.3.2.4.1 Center opening car door assembly, Type A hanger. Infrared door

protection.2.3.2.4.2 Door Size: 30 to 59 inches (762 to 1499 mm).

2.3.2.5 Basis of Design: 2SCP 2-Speed, Center Parting as manufactured by GAL Mfg Company.

2.3.2.5.1 Two speed, center opening car door assembly, Type A hanger. Infrared door protection.

2.3.2.5.2 Door Size: 33 to 83 inches (838 to 2108 mm).

2.3.3 Clutches:

14 20 10-8

2.3.3.1 Basis of Design: LWZ-2-LRC LOW as manufactured by GAL Mfg. Company.2.3.3.1.1 Running Clearance and Car Sill: 2-5/16 to 2-13/16 inches (59 to 71 mm).

2.3.3.2 Basis of Design: LW2-LRC LOW as manufactured by GAL Mfg. Company.2.3.3.2.1 Running Clearance and Car Sill: 2-5/16 to 2-13/16 inches (59 to 71 mm).

2.3.3.3 Basis of Design: LWZ-2-LRC STD as manufactured by GAL Mfg. Company.2.3.3.3.1 Running Clearance: 11/16 to 15/16 inches (17 to 24 mm).2.3.3.3.2 Running Clearance and Car Sill: 2-7/8 inches (73 mm) or more.

2.3.3.4 Basis of Design: LW2-LRC STD as manufactured by GAL Mfg. Company.2.3.3.4.1 Running Clearance: 11/16 to 15/16 inches (17 to 24 mm).2.3.3.4.2 Running Clearance and Car Sill: 2-7/8 inches (73 mm) or more.

2.3.3.5 Basis of Design: LWZ-2-LOW as manufactured by GAL Mfg. Company.2.3.3.5.1 Running Clearance: 1 inch (25 mm) or more.2.3.3.5.2 Running Clearance and Car Sill: 2-11/16 to 3-3/16 inches (68 to 81 mm).

2.3.3.6 Basis of Design: LW2-LOW as manufactured by GAL Mfg. Company.2.3.3.6.1 Running Clearance: 1 inch (25 mm) or more.2.3.3.6.2 Running Clearance and Car Sill: 2-11/16 to 3-3/16 inches (68 to 81 mm).

2.3.3.7 Basis of Design: LWZ-2- as manufactured by GAL Mfg. Company.2.3.3.7.1 Running Clearance: 1 inch (25 mm) or more.2.3.3.7.2 Running Clearance and Car Sill: 3-1/4 inches (83 mm) or more.

2.3.3.8 Basis of Design: LW2 as manufactured by GAL Mfg. Company.2.3.3.8.1 Running Clearance: 1 inch (25 mm) or more.2.3.3.8.2 Running Clearance and Car Sill: 3-1/4 inches (83 mm) or more.

2.3.4 Door Protection:2.3.4.1 Basis of Design: ScanGUARD as manufactured by GAL Mfg. Company.

2.3.4.1.1 Highly rugged, vandal-resistant, simple to use light curtain.2.3.4.1.2 Material: Aluminum alloy.2.3.4.1.3 Light Beams: 63 non-parallel infrared beam paths.2.3.4.1.4 Detection Range: 0 to 6 feet (0 to 1829 mm).2.3.4.1.5 Length: 7 feet (2134 mm).2.3.4.1.6 Power: 24 V DC.2.3.4.1.7 Profile: 1.18 x 0.81 inches (30 x 20 mm).2.3.4.1.8 For use on side or center opening doors.2.3.4.1.9 Tolerant of all environmental, electrical, and radio interference.

2.3.4.2 Basis of Design: Formula Systems SafeScreen as supplied by GAL Mfg. Company.

2.3.4.2.1 Description: Light curtain.2.3.4.2.2 Material: Aluminum alloy.2.3.4.2.3 Light Beams: 47 diagonal infrared beam paths.2.3.4.2.4 Detection Range: 0 to 71 inches (0 to 1800 mm).2.3.4.2.5 Detection Range: 0 to 197 inches (0 to 5000 mm).2.3.4.2.6 Length: 7 feet (2136 mm).2.3.4.2.7 Power: 24 V DC.2.3.4.2.8 Profile: 1.18 x 0.81 inches (30 x 20 mm).2.3.4.2.9 For use on side or center opening doors.2.3.4.2.10 Operating Temperature: -4 to 158 degrees F (-20 to 70 degrees C).

2.3.5 Hatch Door Hanger Assemblies:2.3.5.1 Basis of Design: SS Single Speed as manufactured by GAL Mfg. Company.

2.3.5.1.1 Single speed. Type A hanger. Reel or spring door closer.2.3.5.1.2 Left hand opening.2.3.5.1.3 Right hand opening.2.3.5.1.4 Door Size: 22 to 48 inches (559 to 1219 mm).

2.3.5.2 Basis of Design: 2S Two-Speed as manufactured by GAL Mfg. Company.2.3.5.2.1 Two-speed. Type A hanger. Spring door closer.2.3.5.2.2 Left hand opening.

14 20 10-9

2.3.5.2.3 Right hand opening.2.3.5.2.4 Door Size: 24 to 72 inches (610 to 1829 mm).

2.3.5.3 Basis of Design: 3S Three-Speed as manufactured by GAL Mfg. Company.2.3.5.3.1 Three-speed. Type A hanger. Shoe type spring door closer.2.3.5.3.2 Left hand opening.2.3.5.3.3 Right hand opening.2.3.5.3.4 Door Size: 30 to 69 inches (762 to 1753 mm).

2.3.5.4 Basis of Design: CP Center Parting as manufactured by GAL Mfg. Company.2.3.5.4.1 Center opening. Type A hanger. Spring or reel closer.2.3.5.4.2 Door Size: 24 to 59 inches (610 to 1499 mm).

2.3.5.5 Basis of Design: 2SCP Two-Speed, Center Parting as manufactured by GAL Mfg. Company.

2.3.5.5.1 Two speed, center opening. Type A hanger. Spring door closer.2.3.5.5.2 Door Size: 40 to 110 inches (1016 to 2794 mm).

2.3.6 Interlocks:2.3.6.1 Basis of Design: Type MO Interlock as manufactured by GAL Mfg. Company.

2.3.6.1.1 Standards Compliance:2.3.6.1.1.1 NEMA rated.2.3.6.1.1.2 UL listed.2.3.6.1.1.3 CSA certified.

2.3.6.1.2 Existing Header Pocket Height:2.3.6.1.2.1 Single Speed: 4-1/8 inches (105 mm) minimum.2.3.6.1.2.2 Two Speed Ungeared: 5-1/2 inches (140 mm) minimum.2.3.6.1.2.3 Two Speed Geared: 8-1/4 inches (210 mm) minimum.2.3.6.1.2.4 Two Speed, Center Parting Ungeared: 6-1/2 inches (165 mm)

minimum.2.3.6.1.2.5 Two Speed, Center Parting Geared: 8-1/4 inches (210 mm)

minimum.2.3.6.1.2.6 Three Speed Ungeared: 6-1/2 inches (165 mm) minimum.2.3.6.1.2.7 Center Parting Geared: 4-7/8 inches (124 mm) minimum.2.3.6.1.2.8 Center Parting Ungeared: 4-1/8 inches (105 mm) minimum.

2.3.6.1.3 Additional 1-3/8 inch (35 mm) header pocket height required if adaptor channel is required.

2.3.6.2 Basis of Design: Type N Interlock as manufactured by GAL Mfg. Company.2.3.6.2.1 Operation: Swing door.2.3.6.2.2 Operation: Sliding door.2.3.6.2.3 Flush mounted lock.2.3.6.2.4 Surface mounted lock.

2.3.7 Closers: Basis of Design as manufactured by GAL Mfg. Company.2.3.7.1 Spring Closer. Single Speed. Center Parting Door.2.3.7.2 Spring Closer. Two Speed and Two Speed Center Parting.2.3.7.3 Spring Closer. Two Speed, Large Opening Door.2.3.7.4 Reel Closer. Single Speed Door.2.3.7.5 Reel Closer. Two Speed, Center Parting Door.

2.3.8 Switches and Contacts:2.3.8.1 Basis of Design: Type SN Lock and Electrical Contact as manufactured by GAL

Mfg. Company.2.3.8.1.1 Left hand lock.2.3.8.1.2 Right hand lock.2.3.8.1.3 Box: Surface.2.3.8.1.4 Box: Flush.2.3.8.1.5 Box: Kalamine.2.3.8.1.6 Box: Slide.

14 20 10-10

2.3.8.2 Basis of Design: Type SN-Z Lock and Electrical Contact as manufactured by GAL Mfg. Company.

2.3.8.2.1 Single speed.2.3.8.2.2 Two speed.

2.3.8.3 Basis of Design: Type SN-C Contact as manufactured by GAL Mfg. Company.2.3.8.3.1 Left hand lock.2.3.8.3.2 Right hand lock.2.3.8.3.3 Box: Surface.2.3.8.3.4 Box: Flush.2.3.8.3.5 Box: Kalamine.2.3.8.3.6 Box: Slide.

2.3.9 Fault Monitors:2.3.9.1 Basis of Design: FM1 Door Lock Monitor as manufactured by GAL Mfg.

Company.2.3.9.1.1 Detects jumped or faulty door circuits. Prevents car movement in event of

door failure.2.3.9.1.2 Separate commons for different circuits.2.3.9.1.3 On-board diagnostics and troubleshooting LEDs.2.3.9.1.4 Universal inputs.2.3.9.1.5 Universal, non-proprietary design.2.3.9.1.6 Alarm relay permits audible or visual indication.

2.3.9.2 Basis of Design: FMG1 as manufactured by GAL Mfg Company.2.3.9.2.1 Provides unintended car movement detection and ascending or

descending over-speed detection.2.3.9.2.2 Interfaces with FM1 and Rope Gripper Unit to provide simple means to halt

car motion when a fault is detected.2.3.9.2.3 Board displays status of elevator doors and elevator motion.2.3.9.2.4 On-board LCD and keypad for diagnostics and troubleshooting.2.3.9.2.5 Universal inputs.2.3.9.2.6 Universal, non-proprietary design.2.3.9.2.7 Incremental encoder interface for elevator speed feedback.2.3.9.2.8 Second incremental encoder feedback to provide redundancy or slip

detection.2.3.9.2.9 Monitors brake lift switch.

2.4 ELEVATOR HOISTING EQUIPMENT (Hollister and Whitney)

2.4.1 Overhead Traction Machines:2.4.1.1 Standard Equipment:

2.4.1.1.1 Motor coupling bored with keyway.2.4.1.1.2 Fabricated steel base.2.4.1.1.3 Demountable traction sheave.2.4.1.1.4 Demountable bronze gear.2.4.1.1.5 Steel worm on integral shaft.2.4.1.1.6 Motor mounting pads.2.4.1.1.7 Customer name on housing cover.

2.4.1.1.7.1 Name: _____.2.4.1.2 Rated Car Capacity: _____.2.4.1.3 Rated Car Speed: _____2.4.1.4 Roping: 1 to 1.2.4.1.5 Roping: 2 to 1.2.4.1.6 Hoist Ropes:

2.4.1.6.1 Number: _____.2.4.1.6.2 Size: _____.2.4.1.6.3 Pitch: _____.

14 20 10-11

2.4.1.7 Hoist Motor Manufacturer: _____.2.4.1.7.1 Horsepower and RPM: _____.

2.4.1.8 Power Supply: _____.2.4.1.9 Isolation Dimensions: ______.2.4.1.10 Included Options:

2.4.1.10.1 Drip pans.2.4.1.10.2 Mileage recorder and drive assembly.2.4.1.10.3 Brake switch.2.4.1.10.4 Sheave guard.2.4.1.10.5 Machine isolation assembly, standard.2.4.1.10.6 Machine isolation assembly, seismic.2.4.1.10.7 Motor mounting by manufacturer.2.4.1.10.8 Manual brake release.2.4.1.10.9 Drum brake.2.4.1.10.10 Rope gripper mounting provisions.2.4.1.10.11 VVVF-AC hoist motor.2.4.1.10.12 Machine block-up assembly.

2.4.1.11 Basis of Design: Machine No. 34 as manufactured by Hollister-Whitney Elevator Co.:

2.4.1.11.1 Direct current brake with disc brake.2.4.1.11.2 Maximum Shaft Load: 11,000 pounds (4990 kg).2.4.1.11.3 Machine Weight Less Motor: 1200 pounds (544 kg).




2.4.1.13.1 Direct current brake with disc brake.2.4.1.13.2 Maximum Shaft Load: 26,000 pounds (11,793 kg).2.4.1.13.3 Machine Weight Less Motor: 2300 pounds (1043 kg).




2.4.1.15.1 Drum brake.2.4.1.15.2 Maximum Shaft Load: 60,000 pounds (27,216 kg).2.4.1.15.3 Machine Weight Less Motor: 5500 pounds (2495 kg).

2.4.2 Basement Set Traction Machines2.4.2.1 Standard Equipment:

2.4.2.1.1 Steel shaft support block.2.4.2.1.2 Narrow steel outboard stand.2.4.2.1.3 Motor coupling bored with keyway.2.4.2.1.4 Fabricated steel base.2.4.2.1.5 Demountable traction sheave.2.4.2.1.6 Demountable bronze gear.2.4.2.1.7 Steel worm on integral shaft.2.4.2.1.8 Motor mounting pads.2.4.2.1.9 Customer name on housing cover.

2.4.2.1.9.1 Name: _____.2.4.2.2 Rated Car Capacity: _____.

14 20 10-12

2.4.2.3 Rated Car Speed: _____2.4.2.4 Roping: 1 to 1.2.4.2.5 Roping: 2 to 1.2.4.2.6 Handing: Left hand.2.4.2.7 Handing: Right hand.2.4.2.8 Hoist Ropes:

2.4.2.8.1 Number: _____.2.4.2.8.2 Size: _____.


2.4.2.10 Power Supply: _____.2.4.2.11 Included Options:

2.4.2.11.1 Drip pans.2.4.2.11.2 Mileage recorder and drive assembly.2.4.2.11.3 Brake switch.2.4.2.11.4 Sheave guard.2.4.2.11.5 Machine template.2.4.2.11.6 Foundation bolts and pipe spacers.2.4.2.11.7 Motor mounting by manufacturer.2.4.2.11.8 Manual brake release.2.4.2.11.9 Drum brake.2.4.2.11.10 Rope gripper mounting provisions.2.4.2.11.11 VVVF-AC hoist motor.








2.4.2.15.1 Drum brake.2.4.2.15.2 Maximum Shaft Load: 60,000 pounds (27,216 kg).2.4.2.15.3 Machine Weight Less Motor: 5500 pounds (2495 kg).

2.4.3 Overhead Deflector Machines2.4.3.1 Standard Equipment:

2.4.3.1.1 Direct current disc brake.2.4.3.1.2 Motor coupling bored with keyway.2.4.3.1.3 Fabricated steel base.2.4.3.1.4 Demountable traction sheave.2.4.3.1.5 Demountable bronze gear.2.4.3.1.6 Steel worm on integral shaft.2.4.3.1.7 Motor mounting pads.2.4.3.1.8 Demountable deflector sheave.2.4.3.1.9 Customer name on housing cover.

2.4.3.1.9.1 Name: _____.

14 20 10-13

2.4.3.2 Rated Car Capacity: _____.2.4.3.3 Rated Car Speed: _____2.4.3.4 Roping: 1 to 1.2.4.3.5 Roping: 2 to 1.2.4.3.6 Handing: Left hand.2.4.3.7 Handing: Right hand.2.4.3.8 Hoist Ropes:

2.4.3.8.1 Number: _____.2.4.3.8.2 Size: _____.


2.4.3.10 Power Supply: _____.2.4.3.11 Included Options:

2.4.3.11.1 Drip pans.2.4.3.11.2 Mileage recorder and drive assembly.2.4.3.11.3 Brake switch.2.4.3.11.4 Sheave guard.2.4.3.11.5 Machine template.2.4.3.11.6 Foundation bolts and pipe spacers.2.4.3.11.7 Motor mounting by manufacturer.2.4.3.11.8 Manual brake release.2.4.3.11.9 Drum brake.2.4.3.11.10 Rope gripper mounting provisions.2.4.3.11.11 VVVF-AC hoist motor.


2.4.3.12.1 Maximum Shaft Load: 20,000 pounds (9072 kg).2.4.3.12.2 Machine Weight Less Motor: 1600 pounds (726 kg).


2.4.3.13.1 Maximum Shaft Load: 26,000 pounds (11,793 kg).2.4.3.13.2 Machine Weight Less Motor: 2300 pounds (1043 kg).





2.4.4 Gearless Machines2.4.4.1 Features:

2.4.4.1.1 Can maintain existing deflector sheaves in most cases.2.4.4.1.2 Smooth, quiet and cool operation.2.4.4.1.3 Uses standard core traction steel hoist rope or high strength IWRC rope.2.4.4.1.4 Sealed maintenance free bearings.2.4.4.1.5 Fits through 36 inch (914 mm) wide door.2.4.4.1.6 Excellent ride quality.2.4.4.1.7 Low maintenance.

2.4.4.2 Included Options:2.4.4.2.1 Two independent braking systems.2.4.4.2.2 Rope Gripper.2.4.4.2.3 Regenerative drive for additional electrical savings.

2.4.4.3 Basis of Design: Machine No. GL 100 as manufactured by Hollister-Whitney Elevator Co.:

14 20 10-14

2.4.4.3.1 Roping: 2 to 1.2.4.4.3.2 Counterweight: 50 percent.2.4.4.3.3 Suited for machine-room-less applications.2.4.4.3.4 Maximum System Load: 23,500 pounds (10,660 kg).2.4.4.3.5 Maximum Car Speed: 400 fpm (2.03 mps).2.4.4.3.6 Sheave: 15 inch (381 mm) diameter for 3/8 inch (9.5 mm) ropes.2.4.4.3.7 Sheave: 20 inch (508 mm) diameter for 1/2 inch (13 mm) ropes.





2.4.4.6 Basis of Design: Machine No. GL 130A as manufactured by Hollister-Whitney Elevator Co.:

2.4.4.6.1 Roping: 1 to 1.2.4.4.6.2 Counterweight: 40 percent.2.4.4.6.3 Maximum System Load: 24,750 pounds (11,200 kg).2.4.4.6.4 Maximum Car Speed: 700 fpm (3.56 mps).2.4.4.6.5 Sheave: 20 inch (508 mm) diameter for 1/2 inch (13 mm) ropes.2.4.4.6.6 Sheave: 25 inch (635 mm) diameter for 5/8 inch (16 mm) ropes.




2.4.4.8.1 Roping: 1 to 1.2.4.4.8.2 Counterweight: 40 percent.2.4.4.8.3 Maximum System Load: 25,700 pounds (11,650 kg).2.4.4.8.4 Maximum Car Speed: 700 fpm (3.56 mps).2.4.4.8.5 Sheave: 15 inch (381 mm) diameter for 3/8 inch (9.5 mm) ropes.2.4.4.8.6 Sheave: 20 inch (508 mm) diameter for 1/2 inch (13 mm) ropes.


2.4.4.9.1 Roping: 1 to 1.2.4.4.9.2 Counterweight: 40 percent.2.4.4.9.3 Maximum System Load: 23,350 pounds (10,500 kg).2.4.4.9.4 Maximum Car Speed: 700 fpm (3.56 mps).

14 20 10-15

2.4.4.9.5 Sheave: 25 inch (635 mm) diameter for 5/8 inch (16 mm) ropes.2.4.4.10 Basis of Design: Machine No. GL 260 as manufactured by Hollister-Whitney

Elevator Co.:2.4.4.10.1 Roping: 1 to 1.2.4.4.10.2 Counterweight: 40 percent.2.4.4.10.3 Maximum System Load: 26,700 pounds (12,100 kg).2.4.4.10.4 Maximum Car Speed: 700 fpm (3.56 mps).2.4.4.10.5 Sheave: 25 inch (635 mm) diameter for 5/8 inch (16 mm) ropes.

2.4.5 Rope Grippers:2.4.5.1 Basis of Design: Rope Guide as manufactured by Hollister-Whitney Elevator Co.:

2.4.5.1.1 Material: Aluminum.2.4.5.1.2 Rope Diameter: 3/4 inch (19 mm).2.4.5.1.3 Rope Diameter: _____.2.4.5.1.4 Pitch of Rope: 7 degrees.2.4.5.1.5 Pitch of Rope: ______.2.4.5.1.6 Number of Ropes: ______.2.4.5.1.7 Out to Out of Ropes: 8-1/4 inches (210 mm).2.4.5.1.8 Out to Out of Ropes: 13-3/4 inches (349 mm).2.4.5.1.9 Out to Out of Ropes: _____.

2.4.5.2 Basis of Design: Rope Gripper as manufactured by Hollister-Whitney Elevator Co.:

2.4.5.2.1 Description: Grabs elevator suspension ropes to stop the elevator in the event of a mechanical or electrical failure.

2.4.5.2.2 Gently applied powerful grip doesn't damage rope.2.4.5.2.3 Easy alignment with adequate clearances between rope and self-grooving

grip linings.2.4.5.2.4 Power compensation with constant powerful force.2.4.5.2.5 Material: Aluminum.2.4.5.2.6 Model No. 618 with 1 to 1 Roping: Rated Speed: 250 fpm (1.27 mps).

2.4.5.2.6.1 Maximum Out to Out of Cables: 3-3/8 inches (86 mm).2.4.5.2.6.2 Car Rated Load: 1800 pounds (816 kg).

2.4.5.2.7 Model No. 620 with 1 to 1 Roping: Rated Speed: 350 fpm (1.78 mps).2.4.5.2.7.1 Maximum Out to Out of Cables: 4-7/8 inches (124 mm).2.4.5.2.7.2 Car Rated Load: 2500 pounds (1134 kg).

2.4.5.2.8 Model No. 622 with 1 to 1 Roping: Rated Speed: 600 fpm (3.05 mps).2.4.5.2.8.1 Maximum Out to Out of Cables: 6 inches (152 mm).2.4.5.2.8.2 Car Rated Load: 5000 pounds (2268 kg).

2.4.5.2.9 Model No. 624 with 1 to 1 Roping: Rated Speed: 1200 fpm (6.10 mps).2.4.5.2.9.1 Maximum Out to Out of Cables: 10 inches (254 mm).2.4.5.2.9.2 Car Rated Load: 5000 pounds (2268 kg).


2.4.5.2.11 Model No. 626 with 1 to 1 Roping: Rated Speed: 1200 fpm (6.10 mps).2.4.5.2.11.1 Maximum Out to Out of Cables: 10 inches (254 mm).2.4.5.2.11.2 Car Rated Load: 10,000 pounds (4536 kg).




14 20 10-16


2.4.5.2.16 Model No. 625 with 2 to 1 Roping: Rated Speed: 800 fpm (4.06 mps).2.4.5.2.16.1 Maximum Out to Out of Cables: 11-1/2 inches (292 mm).2.4.5.2.16.2 Car Rated Load: 10,000 pounds (4536 kg).


2.4.6 Sheaves:2.4.6.1 Includes: Shaft, bearings, support blocks, and mounting hardware.2.4.6.2 Hoist Cables:

2.4.6.2.1 Number: _____.2.4.6.2.2 Size: _____.2.4.6.2.3 Centerline to Centerline Dimension: _____.

2.4.6.3 Type of Sheave Supports: ______.2.4.6.4 Beam Spacing: ______.2.4.6.5 Capacity: ______.2.4.6.6 Speed: _____.2.4.6.7 Basis of Design: Standard Deflector Sheaves as manufactured by Hollister-

Whitney Elevator Co.:2.4.6.7.1 Pitch Diameter: 20 inches (508 mm).

2.4.6.7.1.1 Rim Width: 4 inches (102 mm).2.4.6.7.1.2 Rim Width: 5-3/4 inches (146 mm).2.4.6.7.1.3 Rim Width: 6-1/2 inches (165 mm).2.4.6.7.1.4 Rim Width: 7-1/4 inches (184 mm).

2.4.6.7.2 Pitch Diameter: 25 inches (635 mm).2.4.6.7.2.1 Rim Width: 4-1/2 inches (114 mm).2.4.6.7.2.2 Rim Width: 5-3/4 inches (146 mm).2.4.6.7.2.3 Rim Width: 7-1/4 inches (184 mm).

2.4.6.8 Basis of Design: Heavy Duty Deflector Sheaves as manufactured by Hollister-Whitney Elevator Co.:

2.4.6.8.1 Pitch Diameter: 25 inches (635 mm).2.4.6.8.1.1 Rim Width: 4-1/2 inches (114 mm).2.4.6.8.1.2 Rim Width: 6-1/2 inches (165 mm).2.4.6.8.1.3 Rim Width: 7-1/2 inches (191 mm).

2.4.6.8.2 Pitch Diameter: 26 inches (660 mm). Rim Width: 10 inches (254 mm).2.4.6.8.3 Pitch Diameter: 30 inches (762 mm). Rim Width: 6-1/2 inches (165 mm).

2.4.6.9 Basis of Design: Overhead Sheaves as manufactured by Hollister-Whitney Elevator Co.:

2.4.6.9.1 Pitch Diameter: 15-3/4 inches (400 mm).2.4.6.9.1.1 Rim Width: 4-1/4 inches (108 mm).2.4.6.9.1.2 Rim Width: 5-1/2 inches (140 mm).

2.4.6.9.2 Pitch Diameter: 20 inches (508 mm). Rim Width: 6-1/2 inches (165 mm).2.4.6.9.3 Pitch Diameter: 25 inches (635 mm).

2.4.6.9.3.1 Rim Width: 6-1/2 inches (165 mm).2.4.6.9.3.2 Rim Width: 8-1/2 inches (216 mm).

2.4.6.9.4 Pitch Diameter: 26 inches (660 mm). Rim Width: 10 inches (254 mm).2.4.6.9.5 Pitch Diameter: 30 inches (762 mm).

2.4.6.9.5.1 Rim Width: 6-1/2 inches (165 mm).2.4.6.9.5.2 Rim Width: 8-1/2 inches (216 mm).

2.4.7 Roller Guide Shoes:2.4.7.1 Tension system causes rollers to adjust for loads near balanced point and for rail

misalignment.

14 20 10-17

2.4.7.2 Features:2.4.7.2.1 Sealed bearings.2.4.7.2.2 Heavy duty polyurethane precision rollers.2.4.7.2.3 Standard industry mountings.

2.4.7.3 Basis of Design: Model No. 377 as manufactured by Hollister-Whitney Elevator Co.:

2.4.7.3.1 Rollers: Three 3-1/4 inch (83 mm) rollers.2.4.7.3.2 Mounting: Car.

2.4.7.3.2.1 Capacity: 2000 pounds (907 kg).2.4.7.3.2.2 Maximum Speed: 300 fpm (1.52 mps).

2.4.7.3.3 Mounting: Counterweight.2.4.7.3.3.1 Capacity: 5000 pounds (2268 kg).2.4.7.3.3.2 Maximum Speed: 600 fpm (3.05 mps).


2.4.7.4.1 Rollers: Three 6 inch (152 mm) rollers.2.4.7.4.2 Mounting: Car.



2.4.7.5.1 Rollers: Four 3-1/4 inch (83 mm) rollers.2.4.7.5.2 Mounting: Car.


2.4.7.5.3 Mounting: Counterweight.2.4.7.5.3.1 Capacity: 8000 pounds (3629 kg).2.4.7.5.3.2 Maximum Speed: 1000 fpm (5.08 mps).


2.4.7.6.1 Rollers: Four 6 inch (152 mm) rollers.2.4.7.6.2 Mounting: Car.



2.4.7.7.1 Rollers: High speed roller guide shoe.2.4.7.7.2 Capacity: 6000 pounds (2722 kg).2.4.7.7.3 Maximum Speed: 1600 fpm (8.13 mps).2.4.7.7.4 Absorbs shift with springs located in each individual arm.2.4.7.7.5 Six 10 inch (254 mm) rollers.2.4.7.7.6 Adjustable travel stops.2.4.7.7.7 Rail tracking adjustment.

2.4.8 Rigid and Swivel Guide Shoes:2.4.8.1 Basis of Design: Model No. 371 as manufactured by Hollister-Whitney Elevator

Co.2.4.8.2 Basis of Design: Model No. 375 as manufactured by Hollister-Whitney Elevator





14 20 10-18

Co.

2.4.9 Disk and Drum Brakes:2.4.9.1 Basis of Design: DC Disc Brakes as manufactured by Hollister-Whitney Elevator

Co.2.4.9.1.1 Completely enclosed coil.2.4.9.1.2 Individual spring tension adjustments.2.4.9.1.3 Individual stroke adjustments.2.4.9.1.4 Machine Speed: _____.2.4.9.1.5 Machine Capacity: _____.2.4.9.1.6 Distance from Center Line of Worm Shaft to Top of Bedplate: _____.2.4.9.1.7 Voltage and Type of Motor Control: _____.

2.4.9.2 Basis of Design: DC Drum Brakes as manufactured by Hollister-Whitney Elevator Co.

2.4.9.2.1 Completely enclosed coil.2.4.9.2.2 Individual spring tension adjustments.2.4.9.2.3 Individual stroke adjustments.2.4.9.2.4 Pivot shoes with toe and heel adjustments.2.4.9.2.5 Model: _____.2.4.9.2.6 Diameter of Brake Drum: _____.2.4.9.2.7 Width of Brake Drum: _____.2.4.9.2.8 Distance from Center Line of Brake Drum to Top of Bedplate: _____.2.4.9.2.9 Speed: _____.2.4.9.2.10 Capacity: _____.2.4.9.2.11 Voltage and Type of Motor Control: _____.2.4.9.2.12 Existing Shoe Contact on Drum: _____.

2.4.10 Safeties:2.4.10.1 Compliance: Comply with ASME A17.1 and EN81.2.4.10.2 Basis of Design: Type B Flexible Guide Clamp Safety as manufactured by

Hollister-Whitney Elevator Co.2.4.10.2.1 Stopping force automatically exerted equally on both sides of each guide

rail.2.4.10.2.2 Full swivel of rail grips for full and uniform contact.2.4.10.2.3 Operating linkage is adjustable.2.4.10.2.4 Car Speed: ____.2.4.10.2.5 Face to Face of Guide Rails: _____.2.4.10.2.6 Rail Size: _____.2.4.10.2.7 Governor Location: _____.2.4.10.2.8 Stile Size: _____.2.4.10.2.9 Type of Guide Shoes: _____.2.4.10.2.10 Gross Load: _____.

2.4.10.3 Basis of Design: Type A Instantaneous Safety as manufactured by Hollister-Whitney Elevator Co.

2.4.10.3.1 Stopping force automatically exerted equally on both sides of each guide rail.

2.4.10.3.2 Operating linkage is adjustable.2.4.10.3.3 Car Speed: ____.2.4.10.3.4 Face to Face of Guide Rails: _____.2.4.10.3.5 Rail Size: _____.2.4.10.3.6 Governor Location: _____.2.4.10.3.7 Stile Size: _____.2.4.10.3.8 Type of Guide Shoes: _____.

2.4.11 Overspeed Governors and Tension Weights:2.4.11.1 Compliance: Comply with ASME A17.1.

14 20 10-19

2.4.11.2 Basis of Design: Pit Mounted Overspeed Governor Model 211 as manufactured by Hollister-Whitney Elevator Co.

2.4.11.2.1 Meets NEMA 4 requirements.2.4.11.2.2 Speed: Up to 500 fpm (2.54 mps).2.4.11.2.3 Sheave Diameter: 12 inches (305 mm).2.4.11.2.4 Configuration: Left hand.2.4.11.2.5 Configuration: Right hand.2.4.11.2.6 Pull Through: 300 to 800 pounds (136 to 363 kg).2.4.11.2.7 Testing: Remote set.2.4.11.2.8 Live shaft for encoder.2.4.11.2.9 Rope stretch switch.2.4.11.2.10 Speed reduction switch.

2.4.11.3 Basis of Design: Overspeed Governor as manufactured by Hollister-Whitney Elevator Co.

2.4.11.3.1 Meets GSA requirements.2.4.11.3.2 Configuration: Left hand.2.4.11.3.3 Configuration: Right hand.2.4.11.3.4 Pull Through: 300 to 1200 pounds (136 to 544 kg).2.4.11.3.5 Speed reduction switch.2.4.11.3.6 Model No. 201: Dead shaft.

2.4.11.3.6.1 Speed: Up to 500 fpm (2.54 mps).2.4.11.3.6.2 Sheave Diameter: 16 inches (406 mm).

2.4.11.3.7 Model No. 202: Live shaft.2.4.11.3.7.1 Speed: Up to 500 fpm (2.54 mps).2.4.11.3.7.2 Sheave Diameter: 16 inches (406 mm).

2.4.11.3.8 Model No. 207: Dead shaft.2.4.11.3.8.1 Speed: Up to 500 fpm (2.54 mps).2.4.11.3.8.2 Sheave Diameter: 12 inches (305 mm).


2.4.11.3.10 Model No. 208: Dead shaft.2.4.11.3.10.1 Speed: Up to 800 fpm (4.06 mps).2.4.11.3.10.2 Sheave Diameter: 16 inches (406 mm).


2.4.11.4 Basis of Design: Tension Weights as manufactured by Hollister-Whitney Elevator Co.

2.4.11.4.1 Model No. 191: Swing type, 12 inch (305 mm) diameter.2.4.11.4.2 Model No. 192: Swing type, 16 inch (406 mm) diameter.2.4.11.4.3 Model No. 193: Frame type, 16 inch (406 mm) diameter.2.4.11.4.4 Model No. 194: Frame type, 12 inch (305 mm) diameter.

2.4.12 Car Slings and Platforms:2.4.12.1 Basis of Design: Car Slings and Platforms as manufactured by Hollister-Whitney

Elevator Co.2.4.12.1.1 Includes: Channel stiles, crossheads, gussets, braces, cable hitch plates,

cutout for sills, fireproofing on underside of wood platform, and one toe guard.

2.4.12.1.2 Included Options:2.4.12.1.2.1 Extra toe guards.2.4.12.1.2.2 Isolated platform.2.4.12.1.2.3 Roller guard shoe balance weights.2.4.12.1.2.4 Wood and steel platform.2.4.12.1.2.5 All steel platform.

14 20 10-20

2.4.12.1.2.6 Compensation hitch.2.4.12.1.2.7 Freight cabs.2.4.12.1.2.8 Vertical rising gates.

2.4.12.1.3 Capacity: _____.2.4.12.1.4 Platform Width: _____.2.4.12.1.5 Platform Depth: _____.2.4.12.1.6 Distance from Front of Platform to Centerline of Car Rails: _____.2.4.12.1.7 Distance between Guides: _____.2.4.12.1.8 Underbeam to Platform Dimension: _____.2.4.12.1.9 Type of Door or Gate: _____.2.4.12.1.10 Side or Corner Post: _____.2.4.12.1.11 Car Sill Detail: _____.2.4.12.1.12 Classification: _____.

2.4.12.2 Counterweight Frames: Basis of Design as manufactured by Hollister-Whitney Elevator Co.

2.4.12.2.1 Top and bottom channels, T bar side stiles, two tie rods, and cable hitch plate.

2.4.12.2.2 Counterweight Frame No. 230.2.4.12.2.3 Counterweight Frame No. 240.2.4.12.2.4 Counterweight Frame No. 250.2.4.12.2.5 Counterweight Frame No. 255.2.4.12.2.6 Counterweight Frame No. 260.

2.4.12.3 Distance between Guides: _____.2.4.12.4 Maximum Overall Height of Frame: _____.2.4.12.5 Maximum Width of Filler Weights: _____.2.4.12.6 Total Counterweight Required: _____.2.4.12.7 Number of Hoist Ropes: _____.2.4.12.8 Size of Hoist Ropes: _____.

2.4.13 Spring and Oil Buffers:2.4.13.1 Complies with ASME A17.1 and GSA safety codes.2.4.13.2 Basis of Design: Oil Buffers as manufactured by Hollister-Whitney Elevator Co.

2.4.13.2.1 Rated Car Speed: _____.2.4.13.2.2 Rated Car Capacity: _____.2.4.13.2.3 Total Counterweight: _____.2.4.13.2.4 Included options:

2.4.13.2.4.1 Switch.2.4.13.2.4.2 Car buffer strut.2.4.13.2.4.3 Pit channels.

2.4.13.2.5 Model No. 500: Maximum Car Speed: 350 fpm (1.78 mps).2.4.13.2.5.1 Maximum Load: 15,000 pounds (6804 kg).





2.4.13.3 Basis of Design: Spring Buffers as manufactured by Hollister-Whitney Elevator Co.

2.4.13.3.1 Rated Car Speed: _____.2.4.13.3.2 Rated Car Capacity: _____.2.4.13.3.3 Empty Car Weight: _____.2.4.13.3.4 Total Counterweight: _____.2.4.13.3.5 Buffer Height: _____.

14 20 10-21

2.4.13.3.6 Include pit channels.

2.4.14 Elevator Equipment Accessories:2.4.14.1 Adjusting kit for No. 34 machines.2.4.14.2 Adjusting kit for No. 44, 54, and 64 machines.2.4.14.3 Adjusting kit for No. 74 machines.2.4.14.4 Adjusting kit for No. 43, 53, and 63 machines.2.4.14.5 Manual brake release for No. 34 machines.2.4.14.6 Manual brake release for No. 44, 54, and 64 machines.2.4.14.7 Manual brake release for No. 74 machines.2.4.14.8 Manual brake release for No. 43, 53, and 63 machines.2.4.14.9 Shim set.2.4.14.10 Wrench set.2.4.14.11 Feeler gauge set.2.4.14.12 Tramming set.2.4.14.13 Magnetic base.2.4.14.14 Mounting brackets for GAL hatch switches.2.4.14.15 Adjustable guide rail brackets.

2.4.14.15.1 Rail Size: _____.2.4.14.15.2 Dimension from Back of Car Rail to Support: _____.2.4.14.15.3 Dimension from Centerline of Counterweight Rails to Support: ______.

2.4.14.16 Guide rails.2.4.14.17 Wedge shackles.

2.4.14.17.1 Rope Size: _____.2.4.14.17.2 Overall Length: _____.2.4.14.17.3 Quantity: ______.

2.4.14.18 Equalizer springs.2.4.14.19 Hoist ropes.2.4.14.20 Governor ropes.

2.4.15 VVVF Motors for Geared Machines:2.4.15.1 Basis of Design: VVVF Low-Slip Hoist Motors as manufactured by Hollister-

Whitney Elevator Co.2.4.15.1.1 Cable: 35 foot (10 meter) encoder cable.2.4.15.1.2 Encoder: 2048 PPR.2.4.15.1.3 Encoder: 1024 PPR.2.4.15.1.4 Constant Torque: 0-60 Hz.2.4.15.1.5 Variable Torque: 60-90 Hz.2.4.15.1.6 Inverter Duty: 60 minute duty.2.4.15.1.7 Extended end play.2.4.15.1.8 Foot mount.2.4.15.1.9 Version: 1200 SRPM.2.4.15.1.10 Version: 900 SRPM.2.4.15.1.11 Version: 1800 SRPM.2.4.15.1.12 Horsepower: _____.2.4.15.1.13 Horsepower: 5 hp.2.4.15.1.14 Horsepower: 50 hp.2.4.15.1.15 Horsepower: 75 hp.2.4.15.1.16 Power: 208/230/460 VAC.2.4.15.1.17 Power: 575 VAC.

2.4.16 MRL Elevators:2.4.16.1 Basis of Design: GAL HW MRL System as manufactured by Hollister-Whitney

Elevator Co.2.4.16.1.1 Compliant with A17.1.2.4.16.1.2 Motor: PMAC gearless machine supported by overhead beams.

14 20 10-22

2.4.16.1.3 Controller: Standard GALaxy gearless traction design.2.4.16.1.4 Car Safety: Instantaneous Guide Clamp.2.4.16.1.5 Car Safety: Flexible Guide Clamp.2.4.16.1.6 Counterweight Frame: Traditional traction design.2.4.16.1.7 Door Equipment: Standard traction elevator design.2.4.16.1.8 Governor: Standard governor, located overhead.

2.4.16.1.8.1 Remote electrical reset or trip.2.4.16.1.9 Ropes: standard core traction steel hoist rope.2.4.16.1.10 Ropes: High strength IWRC rope.2.4.16.1.11 Pit Buffers: Standard traction elevator design.2.4.16.1.12 Rail Brackets: Standard traction elevator design.2.4.16.1.13 Fixtures: GAL signal fixtures.2.4.16.1.14 Cars: _____.2.4.16.1.15 Cars: 1.2.4.16.1.16 Cars: 8.2.4.16.1.17 Travel Distance: 200 feet.2.4.16.1.18 Travel Distance: _____.2.4.16.1.19 Speed: 500 fpm (2.54 mps).2.4.16.1.20 Speed: _____.2.4.16.1.21 Capacity: 5000 pounds (2268 kg).2.4.16.1.22 Capacity: _____.2.4.16.1.23 Roping: 2 to 1.2.4.16.1.24 Type: _____.2.4.16.1.25 Type: Underslung car sheaves.

2.4.16.1.25.1 Plan 101; passenger, side CWT, front opening.2.4.16.1.25.2 Plan 111; hospital or service, side CWT, front opening.2.4.16.1.25.3 Plan 112; hospital or service, side CWT, front/rear opening.2.4.16.1.25.4 Plan 121; passenger, side CWT with combo bracket, front

opening.2.4.16.1.25.5 Plan 122; passenger, side CWT with combo bracket, front/rear

opening.2.4.16.1.25.6 Plan 131; Underslung car sheaves, passenger, rear CWT, front

opening.2.4.16.1.26 Type: Overslung car sheaves.

2.4.16.1.26.1 Plan 201; passenger, side CWT, front opening.2.4.16.1.26.2 Plan 202; passenger, side CWT, front/side opening, corner-post

rails.2.4.16.1.26.3 Plan 211; hospital or service, side CWT, front opening.2.4.16.1.26.4 Plan 212; hospital or service, side CWT, front/rear opening.2.4.16.1.26.5 Plan 221; passenger, side CWT with combo bracket, front

opening.2.4.16.1.26.6 Plan 222; passenger, side CWT with combo bracket, front/rear

opening.2.4.16.1.26.7 Plan 231; passenger, rear CWT, front opening.2.4.16.1.26.8 Plan 232; passenger, rear CWT, front/side opening, corner-post

rails.

2.4.17 Equipment Guarding:2.4.17.1 Comprehensive equipment and personnel protection.2.4.17.2 Robust design approved for use with Hollister-Whitney equipment.2.4.17.3 Universal design works with any equipment configuration.2.4.17.4 Minimal parts for easy installation and usage.2.4.17.5 Large easily removable access panels for machine accessibility.2.4.17.6 Perforated panels maintain machine visibility.2.4.17.7 Field retrofittable on existing installations.2.4.17.8 Basis of Design: As manufactured by Hollister-Whitney Elevator Co.

14 20 10-23

2.4.17.8.1 Governor Guard.2.4.17.8.2 Machine Guard.2.4.17.8.3 Geared Machine Jump Guard.2.4.17.8.4 Deflector Sheave Jump Guard2.4.17.8.5 Counterweight Sheave Jump Guard.2.4.17.8.6 Gearless Machine Jump Guard.

2.4.18 Compensating Rope Tension Sheaves:2.4.18.1 Rated for seismic zones.2.4.18.2 Polyethylene guide shoe inserts.2.4.18.3 Sealed sheave bearings.2.4.18.4 Rope retainers.2.4.18.5 Adjustable weight racks.2.4.18.6 Debris guards.2.4.18.7 Compensating rope sheave switch.2.4.18.8 Working travel up to 12 inches (305 mm).2.4.18.9 Adjustable switch flag.2.4.18.10 Speed Rating: _____.2.4.18.11 Speed Rating: 700 fpm (3.56 mps).2.4.18.12 Minimum Pitch Diameter: 32 times rope diameter.2.4.18.13 Maximum Pull Off or Pull In: 3 inches.2.4.18.14 Basis of Design: as manufactured by Hollister-Whitney Elevator Co.

2.4.18.14.1 Single Sheave Model 346.2.4.18.14.2 Twin Sheave Model 347.

2.5 HYDRAULIC ELEVATOR COMPONENTS (Bore-Max Corporation)

2.5.1 Hydraulic Jacks:2.5.1.1 Basis of Design: Standard Holed and Custom Engineered Hydraulic Jacks as

manufactured by Bore-Max Corp.2.5.1.1.1 Plunger Diameter: _____.2.5.1.1.2 Plunger Diameter: 4 inches (102 mm).2.5.1.1.3 Plunger Diameter: 9-1/2 inches (241 mm).2.5.1.1.4 Cylinder Diameter: _____.2.5.1.1.5 Cylinder Diameter: 6 inches (152 mm).2.5.1.1.6 Cylinder Diameter: 12 inches (305 mm).2.5.1.1.7 Piston Length: _____.2.5.1.1.8 Piston Length: 65 feet (19,812 mm).

2.5.1.2 Basis of Design: Multi-Piece Replacement Pistons and Cylinders as manufactured by Bore-Max Corp.

2.5.1.2.1 Pistons: Precision threaded. Ductile iron inserts. Joints are sealed with O rings.

2.5.1.2.2 Cylinder Sections: Coated with rust prevention mastic.

2.5.2 Pump Units:2.5.2.1 Basis of Design: Submersible Pump Units as manufactured by Bore-Max Corp.

2.5.2.1.1 Flows from 8.3 to 255 gpm (31 to 965 Lpm).2.5.2.1.2 Components enclosed within the tank.2.5.2.1.3 Welded construction.2.5.2.1.4 Leak tested.2.5.2.1.5 Hinged top-front door.2.5.2.1.6 Motor and pump isolated by vibration dampening mounts.

2.5.2.2 Basis of Design: Dry/Belt Driven Pump Units as manufactured by Bore-Max Corp.

2.5.2.2.1 Flows up to 375 gpm (1420 Lpm).2.5.2.2.2 Oil level sight gauge.

14 20 10-24

2.5.2.2.3 Fully tested tank mounted on heavy duty structural steel stand.2.5.2.2.4 Motor and pump isolated by vibration dampening mounts.

2.5.3 Slings and Platform Packages:2.5.3.1 Basis of Design: Standard-Holed Slings and Platforms as manufactured by Bore-

Max Corp.2.5.3.1.1 Stops: ____.2.5.3.1.2 Capacity: ____.2.5.3.1.3 Car Weight: ____.2.5.3.1.4 Gross: ____.2.5.3.1.5 Floor Rise: ____.2.5.3.1.6 Car Speed: ____.2.5.3.1.7 Hoistway Size: ____.2.5.3.1.8 Platform Size: ____.2.5.3.1.9 Cab Height: ____.2.5.3.1.10 Guides: ____.2.5.3.1.11 Retainer Plates: ____.

2.6 CONTROL SYSTEMS (GAL and EC)

2.6.1 Control System. (Elevator Controls)2.6.1.1 Basis of Design: Pixel Control System as manufactured by Elevator Controls.

2.6.1.1.1 Elevator Type: Hydraulic.2.6.1.1.2 Elevator Type: Gearless traction.2.6.1.1.3 Elevator Type: Machine room less traction.2.6.1.1.4 Components:

2.6.1.1.4.1 Pixel car controller.2.6.1.1.4.2 P-TOC: Cartop box with access point.2.6.1.1.4.3 P-COP: Car operation panel interface controller.2.6.1.1.4.4 Landa Positioning System: Dual sensor car positioning system.

Provides absolute cab position information with high tech accuracy.

2.6.1.1.4.5 P-Hall: Hall nodes that communicate using enhanced c-Link CAN-bus serial communication system.

2.6.1.1.5 Interface: Color LCD with Touch and Go interface, one-button access to context responsive help, and intuitive direct-select keys.

2.6.1.1.6 Diagnostics: Powerful yet simplified diagnostic built into system access points.

2.6.1.1.7 Capabilities:2.6.1.1.7.1 Speed: Maximum 300 fpm (1.5 mps).2.6.1.1.7.2 Stops: Maximum 128.2.6.1.1.7.3 Group Size: Maximum 12 cars.2.6.1.1.7.4 Operating Temperature: 32 to 104 degrees F (0 to 40 degrees C).2.6.1.1.7.5 Altitude: Maximum 12,000 feet (3,658 meters).2.6.1.1.7.6 Relative Humidity: Maximum 95 percent.

2.6.2 Traveling Cable. (Elevator Controls)2.6.2.1 Basis of Design: Pixel Traveling Cable as manufactured by Elevator Controls.

2.6.2.1.1 Steel Core Size: 5/32 inch (4.0 mm).2.6.2.1.2 Breaking Strength: 2800 pounds (1270 kg).2.6.2.1.3 Single coaxial conductor.2.6.2.1.4 Five 20 AWG shielded pairs, eighteen 18 AWG wires.2.6.2.1.5 Six 14 AWG wires.

2.6.3 Monitoring. (Elevator Controls)2.6.3.1 Basis of Design: Interact Monitoring System as manufactured by Elevator

Controls.

14 20 10-25

2.6.3.1.1 Provides simultaneous display of multiple elevator systems on a single screen.

2.6.3.1.2 Intuitive point and click interaction and menu-driven navigation.2.6.3.1.3 Reports can be graphically represented.2.6.3.1.4 Real time data including traffic data and analysis, operating sequence

playback, fault logs, elevator performance monitoring, and elevator system management.

2.6.4 Controllers. (GAL)2.6.4.1 Basis of Design: GALaxy IV Controller as manufactured by GAL Mfg. Company.

2.6.4.1.1 Standards Compliance:2.6.4.1.1.1 ASME A17.1/CSA B44.2.6.4.1.1.2 CSA approved.2.6.4.1.1.3 Meets TSSA requirements.2.6.4.1.1.4 California certification.2.6.4.1.1.5 EN-12016.

2.6.4.1.2 Automatic hoistway and limit velocity learning.2.6.4.1.3 Load weighing bypass set-up.2.6.4.1.4 Car and counterweight buffer testing.2.6.4.1.5 Normal and emergency terminal slowdown and brake testing.2.6.4.1.6 Lift brake on inspection.2.6.4.1.7 Reset gripper or emergency brake.2.6.4.1.8 Open or close door upon inspection.2.6.4.1.9 GALileo diagnostic interface.2.6.4.1.10 Included Optional Features:

2.6.4.1.10.1 Attendant operation.2.6.4.1.10.2 Building monitoring.2.6.4.1.10.3 Car call security.2.6.4.1.10.4 Card reader.2.6.4.1.10.5 Cross alignment.2.6.4.1.10.6 Cross cancellation.2.6.4.1.10.7 Distance feedback.2.6.4.1.10.8 Earthquake or counterweight derailment service.2.6.4.1.10.9 Emergency power.2.6.4.1.10.10 Floor lockout security.2.6.4.1.10.11 GALileo machine room display.2.6.4.1.10.12 Hospital emergency service or code blue.2.6.4.1.10.13 Load weighing.2.6.4.1.10.14 Magnetic limit switches.2.6.4.1.10.15 Manual and automatic freight door.2.6.4.1.10.16 Medical emergency service.2.6.4.1.10.17 Motor pre-torque.2.6.4.1.10.18 Rear doors.2.6.4.1.10.19 Serial hall calls.2.6.4.1.10.20 Swing car operation.

2.6.4.2 Basis of Design: GALaxy eHydro Controller as manufactured by GAL Mfg. Company.

2.6.4.2.1 Designed to handle up to six cars per group.2.6.4.2.2 For low- to mid-rise buildings up to eight floors.2.6.4.2.3 Requires fewer wires for connection.2.6.4.2.4 Primary connection mode is traveling cable in swing return.2.6.4.2.5 Serial link to car, hall stations, and lanterns.2.6.4.2.6 APSS features plug-in camera reading optical tape.2.6.4.2.7 Simple board design with coded inputs and outputs.2.6.4.2.8 Full color wiring diagrams.2.6.4.2.9 Diagnostics detailed on Main I/O board through a LCD display.

14 20 10-26

2.6.4.2.10 Included Optional Features:2.6.4.2.10.1 Battery lowering.2.6.4.2.10.2 Call card security.2.6.4.2.10.3 Hall card security.2.6.4.2.10.4 Wi-Fi user interface app.2.6.4.2.10.5 Freight door interface.2.6.4.2.10.6 Short floors.

2.6.5 Safety Controls. (GAL)2.6.5.1 Basis of Design: RESCUvator as manufactured by GAL Mfg. Company.

2.6.5.1.1 Provides for the safe, swift exit of passengers from hydraulic elevators in the event of a power failure or blackout conditions.

2.6.6 Drives. (GAL)2.6.6.1 Basis of Design: HPV 900 Series 2 Elevator Drive as manufactured by Magnetek

Elevator; GAL Mfg. Company.2.6.6.1.1 No oversizing needed, designed for overload capacity.2.6.6.1.2 Internal braking IGBT.2.6.6.1.3 Cooling fans run only when drive is in operation.2.6.6.1.4 Carrier frequency of 10 kHz without drive derating.2.6.6.1.5 Designed and tested to meet the elevator duty cycle.2.6.6.1.6 Rated for elevator duty cycles.2.6.6.1.7 Isolated encoder signals.

2.6.6.2 Basis of Design: RegenAC as manufactured by Magnetek Elevator; GAL Mfg.2.6.6.2.1 Rated for elevator duty cycles.2.6.6.2.2 Compact design for optimized panel space.2.6.6.2.3 Independently sized for regeneration requirements.2.6.6.2.4 Used in conjunction with traditional dynamic braking resistors when line

regeneration is prohibited.2.6.6.3 Basis of Design: HPV 900 AF as manufactured by Magnetek Elevator; GAL Mfg.

2.6.6.3.1 Regenerative power conversion for AC motors.2.6.6.3.2 Clean utility side harmonics.2.6.6.3.3 High overload capacity.2.6.6.3.4 Wide input voltage range of 200 to 480 VAC.2.6.6.3.5 CSA certified and CE approved.

2.6.6.4 Basis of Design: Quattro AC Cube as manufactured by Magnetek Elevator by GAL Mfg.

2.6.6.4.1 Rated for elevator duty cycles.2.6.6.4.2 Compact design for optimized panel space.2.6.6.4.3 Independently sized for regeneration requirements.2.6.6.4.4 Used in conjunction with traditional dynamic braking resistors when line

regeneration is prohibited.2.6.6.5 Basis of Design: COMBIVERT R6-S as manufactured by KEB; GAL Mfg.

2.6.6.5.1 Converts three-phase input to DC voltage.2.6.6.5.2 Supplies single KEB frequency inverter or multiple units via DC

interconnection.2.6.6.5.3 Can be connected in parallel.2.6.6.5.4 Increases stability of DC bus voltage in shared applications.2.6.6.5.5 Returns the excess energy from generating operation to utility supply

system.2.6.6.5.6 Reduces net energy demand.2.6.6.5.7 Reduces heat dissipation.2.6.6.5.8 Replaces braking resistor and braking transistor.

2.6.6.6 Basis of Design: COMBIVERT R6-N as manufactured by KEB; GAL Mfg.2.6.6.6.1 Converts three-phase input to DC voltage.2.6.6.6.2 Supplies single KEB frequency inverter or multiple units via DC

14 20 10-27

interconnection.2.6.6.6.3 Can be connected in parallel.2.6.6.6.4 Increases stability of DC bus voltage in shared applications.2.6.6.6.5 Returns the excess energy from generating operation to utility supply

system.2.6.6.6.6 Reduces net energy demand.2.6.6.6.7 Reduces heat dissipation.2.6.6.6.8 Replaces braking resistor and braking transistor.

2.6.6.7 Basis of Design: COMBIVERT F5 Inverter as manufactured by KEB; GAL Mfg.2.6.6.7.1 Low motor noise with high carrier frequency2.6.6.7.2 Extensive protection for over current, voltage, and temperature.2.6.6.7.3 Voltage and current monitoring in static and dynamic operation.2.6.6.7.4 Short circuit proof and ground-fault proof.2.6.6.7.5 Noise immunity in accordance with IEC1000.2.6.6.7.6 Hardware current regulation.2.6.6.7.7 Integrated temperature-controlled cooling fan.2.6.6.7.8 PM motor control capable.2.6.6.7.9 Synthesized pre torque for roll back compensation.2.6.6.7.10 CE compliant.2.6.6.7.11 Direct position control.2.6.6.7.12 Stationary pole identification.

3 EXECUTION

3.1 EXAMINATION

3.1.1 Do not begin installation until substrates have been properly constructed and prepared.

3.1.2 Hoistway shall be constructed in accordance with ASME A17.1 - Safety Code for Elevators and Escalators. Comply with State and Local codes.

3.1.3 Hoistway shall be plumb and square within tolerance of manufacturer's requirements.

3.1.4 Hoistway shall provide attachment and support of equipment inside hoistway.

3.1.5 If substrate preparation is the responsibility of another installer, notify Architect in writing of unsatisfactory preparation before proceeding.

3.2 PREPARATION

3.2.1 Clean surfaces thoroughly prior to installation.

3.2.2 Prepare surfaces using the methods recommended by the manufacturer for achieving the best result for the substrate under the project conditions.

3.3 INSTALLATION

3.3.1 Install in accordance with manufacturer's instructions approved submittals and in proper relationship with adjacent construction.

3.3.2 Install the components of the elevator system that are required and that are required by jurisdictional authorities to license the elevator.

3.4 FIELD QUALITY CONTROL

3.4.1 Field Inspection: Coordinate field inspection in accordance with appropriate sections in Division 01.

14 20 10-28

3.4.2 Perform tests of elevator as required by ASME A17.1 and governing codes.

3.4.3 Manufacturer's Services: Coordinate manufacturer's services in accordance with appropriate sections in Division 01.

3.5 ADJUSTING

3.5.1 Adjust elevators for proper operation in accordance with manufacturer/installer's instructions.

3.5.2 Adjust elevators for smooth acceleration and deceleration of car so not to cause passenger discomfort.

3.5.3 Adjust doors to prevent opening of doors at landing on corridor side, unless car is at rest at that landing, or is in leveling zone and stopping at that landing.

3.5.4 Remove and replace damaged components that cannot be successfully repaired as determined by Architect.

3.6 CLEANING AND PROTECTION

3.6.1 Clean products in accordance with the manufacturer's recommendations.

3.6.2 Touch-up, repair or replace damaged products before Substantial Completion.

END OF SECTION

14 20 10-29

Date post:	27-Sep-2019
Category:	Documents
Upload:	others
View:	2 times
Download:	0 times

· Web viewSECTION 14 20 10. NON-PROPRIETARY PASSENGER ELEVATOR EQUIPMENT. Display hidden notes...

Documents