Date post: | 03-Jun-2018 |
Category: |
Documents |
Upload: | phan-van-tuan |
View: | 228 times |
Download: | 0 times |
of 50
8/12/2019 WellBG 5800 User Guide V1.3
1/50
Welltech Computer Co., Ltd.
Boarder Gateway 5800 - 1 -
Boarder Gateway 5800SIP Session Boarder
User GuideRelease 1.3
8/12/2019 WellBG 5800 User Guide V1.3
2/50
Welltech Computer Co., Ltd.
Boarder Gateway 5800 - 2 -
DOCUMENTS
CHAPTER1 BOARDER GATEWAY 5800 INTRODUCTION............... - 3 -
BOARDER GATEWAY 5800FEATURES .................................................. -3-BOARDER GATEWAY 5800APPEARANCE DESCRIPTION ......................... -4-
CHAPTER 2 BOARDER GATEWAY 5800 QUICK START ................. - 6 -
LOGIN BOARDER GATEWAY 5800 ........................................................ -7-NETWORK .......................................................................................... -8-SYSTEM TIME ................................................................................... -10-APPLY CHANGE ................................................................................ -13-
CHAPTER 3 CONFIGURATION REFERENCE.................................- 14 -
SYSTEM CONFIGURATION.................................................................. -14-DEBUG CONFIGURATION ................................................................... -20-NATGROUP..................................................................................... -21-ACL ................................................................................................ -22-
IP ACL.........................................................................................- 22 -ANI ACL ...................................................................................... - 22 -
HACONFIGURATION (HIGHAVAILABLE REDUNDANT)OPTIONAL ANDADDITIONAL LICENSE IS REQUIRED. .................................................... -22-PREFIX ROUTE ................................................................................. -25-AAA ................................................................................................ -25-RTPHOST ....................................................................................... -27-CALL INTERCEPTION ......................................................................... -27-ACCOUNT MANAGEMENT................................................................... -28-
CHAPTER 4 SYSTEM CONTROL REFERENCE .............................- 29 -
UPGRADE......................................................................................... -29-RELOGIN .......................................................................................... -29-
CHAPTER 5 SYSTEM MONITOR REFERENCE .............................. - 30 -
SUBSCRIBER STATUS........................................................................ -30-CALL STATISTICS .............................................................................. -31-RTPSTATUS .................................................................................... -32-RTPSTATISTICS ............................................................................... -32-SERVER STATUS............................................................................... -33-EVENT LOG ...................................................................................... -33-DEBUG INFO..................................................................................... -35-PING................................................................................................ -36-
CHAPTER 6 TELNET & RS-232 CONFIGURATION ........................ - 37 -
CHAPTER 7 LCD DISPLAY CONFIGURATION ...............................- 45 -APPENDIX 1 TIME ZONE TO COUNTRY MAPPING LIST............... - 48 -
8/12/2019 WellBG 5800 User Guide V1.3
3/50
8/12/2019 WellBG 5800 User Guide V1.3
4/50
Welltech Computer Co., Ltd.
Boarder Gateway 5800 - 4 -
Application Example:
Hosted PABX Customer Side SBC Hosted Call Center Customer Side VOIP Recording Soft-Switch Server Side SBC
Lawful Interception for Soft-Switch
Architecture:
Boarder Gateway 5800 Appearance Description
Boarder Gateway 5800 Front Panel:
Functions:1: Power LED2: Network1 Interface LED (not used)
WellBG 5800 Applications
IAD
Class 5 Soft-Switch
VOIPCore
Network
InternetNATed
Private Net-work
Private Net-workPrivate Net-
work
NATedPrivate Net-
work
IAD
Soft-phone
Enable NAT UsersAuto RTP proxyPlug and PlaySoft-Switch Protection
N+1 Redundant
WellBG 5800
WellBG 5800
IP PhoneIP Phone
1
2 34
5
6
7
8
8/12/2019 WellBG 5800 User Guide V1.3
5/50
Welltech Computer Co., Ltd.
Boarder Gateway 5800 - 5 -
3: Network2 Interface LED (not used)4: H/D LCD5: Power Switch6: System Status LED7: LCD Panel
8: LCD Touch Panel
Boarder Gateway 5800 Rear Panel:
Functions: 1: Electric Fan2: AC Power outlet3: AC Power switch4: Keyboard/Mouse5: Console port
6: SIP Service Ethernet port7: Management Ethernet port8: VGA9: USB (not used)
91
2
3
4
5
67
8
8/12/2019 WellBG 5800 User Guide V1.3
6/50
Welltech Computer Co., Ltd.
Boarder Gateway 5800 - 6 -
Chapter 2 Boarder Gateway 5800 Quick Start
After connected Ethernet cables into the Boarder Gateway5800 Service Interface, turned on the power. The first step is to
logon the system and set up the IP address.Before you can use the browser to config Boarder Gateway
5800, you need to install Java Plug-in. Please confirm your JREversion is 1.4.2(preferred & tested), if your PC has already in-stalled Java.
You also need to set newer versions of stored pages inInternet Explorer to Every visit to the page. Click Tool > InternetOption > General > Setting.
After success, restart your browser to take effect.
8/12/2019 WellBG 5800 User Guide V1.3
7/50
Welltech Computer Co., Ltd.
Boarder Gateway 5800 - 7 -
Login Boarder Gateway 5800
Step1: Start IE6.0 (or later version) to navigate Boarder Gateway5800 web management system by typing the default URL
is http://192.168.111.161:10087. The screen will displayUser ID and Password as figure 2.1-1.
Figure 2.1-1Note: The default network IP address is:
Service Interface: 192.168.111.161/ 255.255.0.0/192.168.111.254
Management Interface: 192.168.111.151/ 255.255.0.0
Make sure your PC had same network IP address setting
(e.g. 192.168.111.33/255.255.255.0) Otherwise, you will un-able to connect to Boarder Gateway 5800.
Step 2: Enter login user name and password (the default user idis root and user password is root). You can manage youruser account via web (refer to section Account Man-ager) later.
Figure 2.1-2
Step 3: The screen shows the Home Page of Boarder gateway5800 as Figure 2.1-3.
8/12/2019 WellBG 5800 User Guide V1.3
8/50
Welltech Computer Co., Ltd.
Boarder Gateway 5800 - 8 -
Figure 2.1-3
Network
Boarder Gateway 5800 has 2 network interfaces: Boarder Gateway service interface: Provide service over
this network. If you have DNS record, also you must besetup DNS server to effect.
Management interface: It is used for management pur-pose.
Step 1: After successfully logon to the system, we need tochange the network configuration. Click Control >Network to setup the Service Interface parameters asfigure 2.2-1.
Figure 2.2-1
Step 2: Enter the deserved IP address, submask and defaultgateway. If you are running HA features, please set aunique name to Host Name. Apply the change by clicking
Applybutton as figure 2.2-2.
8/12/2019 WellBG 5800 User Guide V1.3
9/50
Welltech Computer Co., Ltd.
Boarder Gateway 5800 - 9 -
Figure 2.2-2
Step 3: When screen shows Change network configurationmay cause server disconnected, are you sure? clickOKbutton to change IP address as figure 2.2-3.
Figure 2.2-3
Step 4: When screen shows After configuration changed,please re-login system with new IP address andexecute Soft-Reset! click OKbutton as figure 2.2-4.
Figure 2.2-4
Step 5: Follow Step 1 to 4 to change management interfacenetwork configuration as figure 2.2-5.
8/12/2019 WellBG 5800 User Guide V1.3
10/50
Welltech Computer Co., Ltd.
Boarder Gateway 5800 - 10 -
Figure 2.2-5Note: Network control takes around 5-second to apply the new
network configuration. Please logon again with new IP ad-dress after 5 seconds.
System Time
Step 1: When re-logon to the new IP address, the next is to setupthe system time zone. Click Control > System Time tosetup the system. Enter current date and time. Apply thechange by clickingApplybutton as figure 2.3-1.
Figure 2.3-1
Step 2: Time Zone SettingStandard: Select the Standard option to setup the system pre-
defined time zone as figure 2.3-2.
Figure 2.3-2
8/12/2019 WellBG 5800 User Guide V1.3
11/50
Welltech Computer Co., Ltd.
Boarder Gateway 5800 - 11 -
Parameter: Time Zone:
Standard: Use a predefined standard time zone (Refer tosection Time zone to Country Mapping List)
Customize: Use a user defined time zone Auto Daylight Saving: Auto adjust daylight saving time or not
User defined time zone: Select the customized option andenter the time zone bias to set a user-defined time zone as figure2.3-3.
Figure 2.3-3Parameter Description: Daylight Bias: The offset added to the Bias when the time
zone is in daylight saving time
Daylight Start: The date that a time zone enters daylight time- Month: 01 to 12- Week Day: Sunday to Saturday- Apply Week (Day:01 to 05, Specifies the occurrence of
day in the month; 01 = First occurrence of day, 02 =Second occurrence of day, ...and 05 = Last occurrence ofday)
- Hour: 00 to 23 Standard Start: The date that a time zone enters daylight time
- Month: 01 to 12- Week Day: Sunday to Saturday
- Apply Week (Day:01 to 05, Specifies the occurrence ofday in the month; 01 = First occurrence ofday, 02 = Second occurrence of day, ...and05 = Last occurrence of day)
- Hour: 00 to 23
8/12/2019 WellBG 5800 User Guide V1.3
12/50
Welltech Computer Co., Ltd.
Boarder Gateway 5800 - 12 -
Step 3: If you would like to use SNTP to sync time with a SNTPV4 Server, click Time Syncbutton to setup it as figure2.3-4.
Figure 2.3-4
Parameter Description: SNTP Server: This is the list of server names. The names
may be separated with semicolons, commas, or spaces. Polling Interval (second): If startup sync is false, try to set the
time each time this many seconds elapses. Min Retry Interval (second): This is the initial retry interval.
NTP client will always wait at least this long between retryattempts when there are errors.
Max Retry Interval (second): This is the max time NTP client
will ever wait before attempting a retry when there have beenerrors.
Max Adjust Time (second): If this is zero, NTP client will bewilling to apply any size time adjustment. If this is non-zero,then any time adjustment greater than this will be consideredan error.
NTP Server Port: This is the port number NTP client will at-tempt to connect to on the time server. The default value is123.
Local NTP Port: This is the port number NTP client will use tolisten for replies from the server. The default value of 0means use a random port number.
Packet Error Check: Enable to validate the contents of theincoming replies from NTP sever or not.
If you need to check the SNTP log, please use Get Logbutton toreview the NTP time log (advance user only).
8/12/2019 WellBG 5800 User Guide V1.3
13/50
Welltech Computer Co., Ltd.
Boarder Gateway 5800 - 13 -
Step 4:After successfully base setup, click Control > Systemtorestart Boarder Gateway 5800 to take effect as figure2.3-5.
Figure 2.3-5
Apply Change
When you loaded a new working configuration or changed any
configuration, you need click Apply Change to take effect asfigure 2.4-1.
Figure 2.4-1
8/12/2019 WellBG 5800 User Guide V1.3
14/50
Welltech Computer Co., Ltd.
Boarder Gateway 5800 - 14 -
Chapter 3 Configuration Reference
System Configuration
Start Path: Configuration > System Configuration
Figure 3.1-1Parameter Description:
SIP Domain:SIP domain for soft-switch or SIP proxy server. Itcan be either the IP address of soft-switch or SIP domain.
Version: The Web version of WellBG 5800 Proxy Server: The Proxy Server or soft-switch IP address
which WellBG 5800 register to Proxy Service Port: The Proxy Service UDP port number Proxy Register TTL: The default registration maximum time to
live setting when register to the proxy Local UDP Port 1,2 and 3: The local UDP port on which the
WellBG 5800 listened- Encrypt: The SIP signal and voice RTP will be encrypted
while passing through the UDP port.- Proxy Connecting Port: It is used to connect to the proxy.
You only can select one from the three ports. IP ACL: IP ACL can be used to filter the caller based on IP
address.
8/12/2019 WellBG 5800 User Guide V1.3
15/50
Welltech Computer Co., Ltd.
Boarder Gateway 5800 - 15 -
- Black: Only on-list IP will be screened.- White: Only on-list IP can get through.
ANI ACL: ANI ACL can be used to filter the caller based onANI number.- Black: Only on-list ANI will be screened.
- White: Only on-list ANI can get through. Min UAC NAT TTL: The minimum register time when a user is
sited behind NAT Max UAC NAT TTL: The maximum register time when a user
is sited behind NAT First Response Timeout: The default maximum time to wait
for response. Its depended on the network speed. Proxy Checking Timer: The interval in seconds used to check
whether the proxy is active or not Proxy Recovery Checking Timer: The interval in seconds
used to check the proxy is active or not when the Proxy isdown or network is failed.
Route to G/W: Local PSTN gateway routing behavior- All: All users can be routed to the local PSTN.- SBC User Only: Only the SBC users can be routed.
RTP Host TTL: The maximum time to wait for external RTPresource server response. Its depended on the networkspeed. (Its only available when working with Welltech ex-ternal RTP resource server)
Enable System Log: Enable to send system information tosyslogD server or not
SysLogD Server IP 1, 2: SyslogD server IP address Event Email Notice: Enable the email notice for the systemevent or not.
Voice Gateway: The voice gateway mode- None: Use this mode when you put the WellBG 5800
and Soft-switch on the public network in this case,WellBG 5800 is used mainly for NAT traversal.
- Client SBC: Use this mode when you are putting theWellBG in client side. In this mode, it supports 2 EthernetLeg mode which private IP leg is connecting to enterpriseLAN and public IP leg is used to connect the Soft switch.
- Server SBC: Use this mode when you are putting the softswitch in the private network and WellBG is setting as 2Ethernet legs which private IP leg is connect to Softswitch and Public IP leg is use to as the outbound proxyof soft switch subscribers.
8/12/2019 WellBG 5800 User Guide V1.3
16/50
Welltech Computer Co., Ltd.
Boarder Gateway 5800 - 16 -
STMP Server: SMTP server host for system event notice Email From: Email sender account Email To: Email receiver Subject: Email subject to be send to receiver. The following
variable parameters can be used to create dynamic subject
for system notice:- $LOGLEVEL$: Information Level- $HOSTNAME$: Host name- $HOSTIP$: Host IP address
Click theAdvancebutton:
Figure 3.1-2
Advance Parameter Descr ip tion: Message Pool Page Size: Used to hold and process all in-
coming and outgoing in the form of encoded message ormessage objects. It is recommended that you configurationthe page size to the average message size your system isexpected to manage.
Message Pool Num of Pages: The pages number of Mes-sage Pool
General Pool Page Size: Used by SIP Stack objects, such ascall-legs and transactions, to store the internal fields. For
example, the call-leg object will store the To, Form andCall-ID headers and the local and remote contact addresseson the general pool pages. The general pool is also used forother activates that demand memory allocation.
General Pool Num of Pages: The pages number of GeneralPool
8/12/2019 WellBG 5800 User Guide V1.3
17/50
Welltech Computer Co., Ltd.
Boarder Gateway 5800 - 17 -
Retransmission T1: T1 determines several timers as definedin RFC3261. For example, when an unreliable transport pro-tocol is used, a Client Invite transaction retransmits requestsat an interval that start at T1 seconds and doubles after everyretransmission. A Client General transaction retransmits re-
quests at an interval that starts at T1 and doubles until itreaches T2. (Default Value: 500ms) **
Retransmission T2: Determines the maximum retransmissioninterval as defined in RFC3261. For example, when an unre-liable transport protocol is used, general requests are re-transmitted at an interval which starts at T1 and doubles untilreaches T2. If a provisional response is received, retrans-mission continue but at an interval of T2. (Default Value:4000ms) **
Retransmission T4:T4 represents the amount of time thenetwork takes to clear message between client and servertransactions as defined in RFC3261. For example, whenworking with an unreliable transport protocol, T4 determinesthe time that UAS waits after receiving an ACK message andbefore terminating the transaction. (Default Value: 5000) **
General Request Timeout Timer: After sending a Generalrequest, the User Agent waits for a final response general-RequestTimeoutTimer milliseconds before timeout termina-tion (in this time the User Agent retransmits the request everyT1, 2*T1,T2,milliseconds)**
Cancel General No Response Timer: When sending a
CANCEL request on a General transaction, the User Agentwaits cancelGeneralNoResponseTimer milliseconds beforetimeout termination if there is no response for the cancelledtransaction(Default Value: 10000ms).**
Processing Queue Size: the maximum length of the proc-essing queue which holds events such as network events.
Proxy 2xx Sent Timer: A successful server INVITE transac-tion of a Proxy server includes only the INVITE request andthe 2xx response. (The ACK is not part of the transac-tion).After sending the 2xx response the Proxy will waitproxy2xxSentTimer before the transaction will terminate.
(default: 8000 ms)** Proxy 2xx Rcvd Timer: A successful client INVITE transaction
of a Proxy server includes only the INVITE request and the2xx response. (The ACK is not part of the transaction.)Afterreceiving the 2xx response, the Proxy will wait
8/12/2019 WellBG 5800 User Guide V1.3
18/50
Welltech Computer Co., Ltd.
Boarder Gateway 5800 - 18 -
proxy2xxRcvdTimer before the transaction terminates. (de-fault: 10000 ms)**
Use Rport Param In Via: Rport is short for Received Portwhich is a parameter in Via Header.
Send Receive Buffer Size: The buffer size used by the SIP
Stack for receiving and sending SIP messages. Register Guard Time: The Register Guard time Max Transactions: The maximum transaction Reject Unregister Call: Reject any unregister call or not Support Video: Enable video RTP Proxy or not. Enable video
will great reduce the number of concurrent channel andbandwidth.
Call Validation Method: Call Valid Check Method: ReInvite,Update or disable
Authentication Failure Protect Timer: The AuthenticationFailure protect timer
Call Validation Timer: The timer to check periodically call isvalid or not.
RTP Reserve Policy:- Called Party: Reserve RTP in called party (please use
only on Welltechs instruction)- Calling Party: Reserve RTP in calling party (recom-
mended mode) Call Failure Reason: The following SIP reason code will be
considered the call is broken or not when WellBG is doing thecall validation.
- When Receiving 481: Only receive 481 response codewill be considered it is a broken call for call validation.- All non 2xx: All of non 2xx response code will be consid-
ered it is a broken call for call validation. WebCaller: Support Web call. To allow web caller can dial
without register or not (Welltech Web call service only)
Advance System Conf iguration:Start Path: Configuration > System > License
Figure 3.1-3
8/12/2019 WellBG 5800 User Guide V1.3
19/50
Welltech Computer Co., Ltd.
Boarder Gateway 5800 - 19 -
License Parameter Description: Feature: System parameter Serial No: System parameter License Key: System parameter
Note: Please do not change it unless under Welltechs instruction.
Click the Local G/W button:
To allow connect to a local PSTN gateway; click LocalG/W to add a PSTN gateway as follows. The local PSTNgateway will also be used for local surviving.
Figure 3.1-4
Create a new item by clicking the Newbutton:
Figure 3.1-5
Parameter Description: Type: The type of the call
- In: The gateway type is for incoming call only for localsurviving. When network is failed or soft-switch is downand client SBC is enabled, the incoming call will be routeto dedicate subscriber in System -> In Route.
- Out: The gateway type is used for PSTN outgoing. Tocontrol the PSTN outgoing right, you can set the Route
to G/W to all or SBC user only. It is recommended toset to SBC user only. The SBC will only accept the callsdialed out the gateway.
- Both: The gateway supports both incoming (IN) andoutgoing (OUT) services.
8/12/2019 WellBG 5800 User Guide V1.3
20/50
Welltech Computer Co., Ltd.
Boarder Gateway 5800 - 20 -
IP: The local gateway IP that the SBC 5800 connected to Port: The local gateway port Sync To Addr: Make the SIP to address to become gateways
IP instead of SIP domain or not. It is recommended to set toTRUE.
Click Local G/W-> L/DMbutton to set the local digit manipula-tion for the call to local gateway.
Figure 3.1-6
Parameter Description: Match Prefix: Called number party matched Start Position: Start position to be replaced Stop Position: Stop position to be replaced Replace Value: Replaced value
Click the IN Route button:
Figure 3.1-7
Parameter Description: Routed Phone Number: The register phone number that the
call from gateway will be routed to when the Proxy or networkis down.
Debug Configuration
Debug can be turn on or off based on each system moduleand level to minimum the debug information.Please only turnon the debug information for debug purpose under WelltechFAE's instruction and turn off when complete. Or the sys-tem performance will be greatly hit.
8/12/2019 WellBG 5800 User Guide V1.3
21/50
Welltech Computer Co., Ltd.
Boarder Gateway 5800 - 21 -
Start Path: Configuration > Debug Configuration
Figure 3.2-1
NAT Group
Boarder Gateway 5800 will not use NAT Proxying when bothsubscribers have same NAT group.
Start Path: Configuration > NAT Group
Figure 3.3-1Parameter Description: Group ID: Group ID Description: Group description
Click on the Detailbutton:
Figure 3.3-2
Parameter Description: IP Address: Public IP address on NAT
8/12/2019 WellBG 5800 User Guide V1.3
22/50
Welltech Computer Co., Ltd.
Boarder Gateway 5800 - 22 -
ACL
Access Control List can be used to filter the calls forms of IPaddress and ANI.
IP ACLStart Path: Configuration > ACL > IP ACL
Figure 3.4-1
Parameter Description: IP Address: IP address used to be filtered
ANI ACL
Start Path: Configuration > ACL > ANI ACL
Figure 3.4-2Parameter Description: ANI: Calling party number used to be filtered
HA Configuration (High Available Redundant) Optional and additional license is required.
WellBC 5800 HA module support N+1 redundant. It providessub-second fail over. However all calls will be dropped after fail
over.Also it supports VIP (virtual IP) for the active node, no
CPE device modification is required to support the HA features.You need setup the available VIPs for each SBC in the cluster.
Start Path: Configuration > HA Configuration
8/12/2019 WellBG 5800 User Guide V1.3
23/50
Welltech Computer Co., Ltd.
Boarder Gateway 5800 - 23 -
Figure 3.5-1Parameter Description:
IP Address: WellBC 5800 real IP address IP Netmask: IP netmask
IP Gateway: IP gateway Active Count: The active node count for this HA cluster. If
you have 6 SBC doing the HA, normally you will set Ac-tive Count to 5 and Standby Count to 1 which is 5+1.
Standby Count: The standby node count for this HA clus-ter. Normally, this count will be 1.
Application Preferred Role: The preferred mode of thisnode is Active or Standby. When you set it to Active,WellBG 5800 will try to make this node to become Activefirst. For an N+1 redundant architecture, please set NSBCs to Active and 1 to Standby.
Cluster: Unique name to identify the HA cluster. All ofnodes should use the same cluster name or it will notwork correctly. The name should not contact any specialdigits like space or @.
Preferred Role: Please set the preferred active node to bemanager and another to standby manager. It is recom-mended to set 1 SBC to manager and others to standbymanager.
Click the Virtual IP> Newbutton to create an IP:
Figure 3.5-2
8/12/2019 WellBG 5800 User Guide V1.3
24/50
Welltech Computer Co., Ltd.
Boarder Gateway 5800 - 24 -
Parameter Description: IP Address: WellBC 5800 virtual IP address for service
You have to set all VIP addresses for each SBC as follows:
For an N+1 HA redundant (N=5), the VIP is shown as follows:
VIP: 211.10.0.1211.10.0.2211.10.0.3211.10.0.4211.10.0.5
To make N+1 redundant, you need to set the virtual IP addressfor each node as follows. The way to set it up will greatly reducethe VIP trying conflict issue.
VIP Settings: First SBC: 211.10.0.1
211.10.0.2211.10.0.3211.10.0.4211.10.0.5
Second SBC: 211.10.0.2211.10.0.3211.10.0.4211.10.0.5211.10.0.1
Third SBC: 211.10.0.3211.10.0.4
211.10.0.5211.10.0.1211.10.0.2
Forth SBC: 211.10.0.4211.10.0.5211.10.0.1211.10.0.2211.10.0.3
Fifth SBC: 211.10.0.5211.10.0.1211.10.0.2211.10.0.3211.10.0.4
8/12/2019 WellBG 5800 User Guide V1.3
25/50
Welltech Computer Co., Ltd.
Boarder Gateway 5800 - 25 -
Prefix Route
Boarder Gateway 5800 Prefix Route can provide prefixhunting base on different usage. SBC5800 will use prefix routingplan to do the corresponding routing. The routing target is a
gateway. Routing policy is defined here.To control which usercan dial to this prefix, setup the Route to G/W in System Con-figuration to all or SBC user only. This prefix also will be usedfor local surviving.
Start Path: Service > Prefix Route
Figure 3.6-1
Modify Prefix Route List:Click the Modify button:
Figure 3.6-2
Parameter Description: Prefix Matched: Called number prefix to be matched Matched Length: Applied only when specified length of DINS
is matched.- Ignore: Select it indicate ignore length option.
Gateway IP: The gateway IP address will be routed to Description: Description
AAA
When WellBG 5800 to do the AAA (Authorization, Authenticationand Accounting), enter the correct parameter about Radius set-ting.
Start Path: Configuration > AAA
8/12/2019 WellBG 5800 User Guide V1.3
26/50
Welltech Computer Co., Ltd.
Boarder Gateway 5800 - 26 -
Figure 3.7-1Parameter Description: Accounting IP: Radius Account Server IP address Accounting Port: Radius Account Server Port Backup Accounting IP: Back Radius Account Server IP ad-
dress Backup Accounting Port: Back Radius Account Server Port Secret Key: The shared secret key with RADIUS Server Max Retry: The maximum retry times Response Timer (sec): The maximum wait for response time
from RADIUS Server Authorization Retry Interval (sec): The internal to resend the
Authentication packet to RADIUS Server. Accounting Retry Interval (sec): The internal to resend the
Account packet to RADIUS Server. Switch Threshold: Switch to alternate RADIUS Server when
failures are occurred more than switch threshold. Billing Message: Call detail record generating mode
- File Only: Log CDR into the file only. It can be retrieved byftp (directory d:\welltech\cdr)
- Radius Start/Stop: Log CDR into the file and send RA-DIUS start/stop billing message out
- Radius Stop: Log CDR into the file and send RADIUSstop billing message out
- None CDR Keepdays: CDR system keeping days
CISCO Mode:- Yes: Use Cisco RADIUS mode (have redundant string invender attribute)
- No: no Send Zero Session Time:
8/12/2019 WellBG 5800 User Guide V1.3
27/50
Welltech Computer Co., Ltd.
Boarder Gateway 5800 - 27 -
- Yes: Send 0-balance session time for RADIUS when thecall failed
- No: no RADIUS Time Format: The time format of the RADIUS server
- UTC: Universal Time Coordinated time format. Some
RADIUS server might not support local time format, it isrecommended to set to UTC time format.
- Local: The local time zone format
RTP Host
By using this feature, WellBG5800 can extend external PTPresource server or have the VOIP logging service. You can de-fine different RTP user ID for different purposes (e.g. by differentISR providers).
Start Path: Configuration > RTP Host > New
Figure 3.8-1
Parameter Description: User ID: The server user ID Password: The server password Type: The device type, RTP server or Recorder Priority: The higher priority number will be used first and then
lower priority number. The same priority number will userround robin to distribute the call.
Call Interception
Call Interception can provide interception service throughtarget call number, be sure that you have an external RecorderServer installed (WellRec 5600).
Start Path: Configuration > Call Interception
8/12/2019 WellBG 5800 User Guide V1.3
28/50
Welltech Computer Co., Ltd.
Boarder Gateway 5800 - 28 -
Figure 3.9-1
Parameter Description: Target Number: The called number to be intercepted or re-
cording Description: Description
Account Management
You can manage (Modify, Add and Delete) the login user ac-
count.Start Path: Configuration > Account Management
Figure 3.10-1Field Descript ion: User ID: Login User ID Password: Login Password
8/12/2019 WellBG 5800 User Guide V1.3
29/50
Welltech Computer Co., Ltd.
Boarder Gateway 5800 - 29 -
Chapter 4 System Control Reference
System, System Time, and Network Please refer to
Chapter 2 -> System Time (Page 10) and Chapter 2 -> Network(Page 8)
Upgrade
Start Path: Control > Upgrade ControlBoarder Gateway 5800 provide upgrade new version at
remote side. You can upgrade it from Welltech technical supportweb page by yourself.
Figure 4.1-1Field Description: File Name: Upload the software file name
Upload: Remote Upload the software at WellBG 5800
Relogin
Start Path: Control > ReloginClick Control > Reloginto relogon by another user account asfigure 4.2-1.
Figure 4.2-1
8/12/2019 WellBG 5800 User Guide V1.3
30/50
Welltech Computer Co., Ltd.
Boarder Gateway 5800 - 30 -
Chapter 5 System Monitor Reference
It provides a way to monitor the system status.
Subscriber Status
Show subscriber users status.
Start Path: Monitor > Subscriber Status > Monitor buttonkey-in the TEL No. and clickApplybutton to be controlled.
Figure 5.1-1
Figure 5.1-2
See the Subscr iber Detail:Select a subscriber and double-click to Subscriber Detail asfigure 5.1-3.
8/12/2019 WellBG 5800 User Guide V1.3
31/50
Welltech Computer Co., Ltd.
Boarder Gateway 5800 - 31 -
Figure 5.1-3Field Descript ion: TEL NO: registered TEL number Register: Registered or not Call Count: number of concurrent calls for the user Call Status: Detail is showed for subscriber. Summary only is
used for gateway user. Contact: Registered contact URI NAT: NAT IP address Register Time: Register time TTL: Register time to live Unreg: Un-register the subscriber Disconnect: Disconnect the connected call
Call Statistics
Show total call statistics records
Start Path: Monitor > Call Statistics
Figure 5.2-1
8/12/2019 WellBG 5800 User Guide V1.3
32/50
Welltech Computer Co., Ltd.
Boarder Gateway 5800 - 32 -
Field Descript ion: Time: statistic period in 24 hours format Peak Call: In this period, the max call reached. Total Call: The total call processed in the period Peak Connected Call: The max connected call in the period
Total connect call: The total connected call in this period Register: For the current period, this field showed real time
registered count. For the past period, this field showed theregister count for last seconds. For example, if current time is10:30, the 10-11 time period show the real time registered calland the 9-10 time period show registered count right on10:00.
Peak Register: The max registered count
RTP Status
Show RTP resource server status. At least the WG5800 itselfwill be showed here as an internal RTP resource server whenhave no extra RTP resource server is defined.
Start Path: Monitor > RTP Status
Figure 5.3-1
RTP Statistics
Show RTP count statistics
Start Path: Monitor > RTP Statistics
Figure 5.4-1
8/12/2019 WellBG 5800 User Guide V1.3
33/50
Welltech Computer Co., Ltd.
Boarder Gateway 5800 - 33 -
Field Descript ion: Time:statistic period in 24 hours format Max NAT: The NAT resource capacity NAT Peak Call: The max NAT call in this period NAT Total Call: Total NAT calls in this period
NAT Fail Call: NAT failed call in this period. It might be indi-cating the resource is exhausted
Server Status
Show current server status.
Start Path: Monitor > Server Status
Figure 5.5-1Parameter Description: Application: System application Version: Application version Status: The application status Call Attempt: The number of concurrent call attempts NAT Call: The number of concurrent NAT calls NAT Fail Call: The failed count to get NAT resource Max Call: The max concurrent call (license number) Current Call: The current call Max Transaction: The max transaction Used Transaction: The used transaction Memory Pool: The allocated memory pool Used Memory: The used memory pool
Event Log
Show system event log status.
Start Path: Monitor > Event Log
8/12/2019 WellBG 5800 User Guide V1.3
34/50
Welltech Computer Co., Ltd.
Boarder Gateway 5800 - 34 -
Figure 5.6-1Field Description: Date: Event created date Time: Event created time
Event ID: Event ID Type: Event Log type- Information- Warring- Error
Source: Executable program Description: The description of the event
Note: You can click Clear button to clear all event log.
See the detailevent log:Select the event and click detail to see the event detail.
Figure 5.6-2
Event Descript ion:Source Event ID Type DescriptionBorderGateway 8000 WARNING Failed to get RTP ResourceBorderGateway 8001 EMERGENCY Failed to detect networkBorderGateway 8002 CRITICAL Outbound Proxy Setting ErrorBorderGateway 8003 EMERGENCY Failed to initiate SIP
8/12/2019 WellBG 5800 User Guide V1.3
35/50
Welltech Computer Co., Ltd.
Boarder Gateway 5800 - 35 -
BorderGateway 8004 EMERGENCY Failed to initiate watch dogBorderGateway 8005 EMERGENCY Failed to create status mutexBorderGateway 8006 EMERGENCY Failed to create status share
memoryBorderGateway 9500 INFOMATION Application Started
BorderGateway 9501 INFOMATION System Shutting DownBorderGateway 9502 INFOMATION Application Closed by UserBorderGateway 9503 INFOMATION Apply ChangeTelnetSvr 9500 INFOMATION TelnetSvr StartedNATProxy 9500 INFOMATION NAT Proxy StartedNATProxy 8000 WARNING SIP Proxy didn't set this RTP
proxyNATProxy 9500 INFOMATION Register to Proxy SuccessNATProxy 8001 INFOMATION Register to Proxy FailNATProxy 8000 WARNING SIP Proxy didn't set this RTP
ProxyNATProxy 8002 WARNING Bind Socket Fail (port=xxxxx)
AAAMgr 9500 INFOMATION AAAMgr startAAAMgr 9501 INFOMATION On the fly change (systemchange)
AAAMgr 8010 WARNING act: Auth server switch fromxxx.xxx.xxx.xxx toxxx.xxx.xxx.xxx
AAAMgr 8010 WARNING act: Acct server switch fromxxx.xxx.xxx.xxx toxxx.xxx.xxx.xxx
AAAMgr 8010 WARNING act: Auth server switch fromxxx.xxx.xxx.xxx toxxx.xxx.xxx.xxx
Debug Info
Shows detail trace level messages.
Start Path: monitor > Debug Info
Figure 5.7-1
8/12/2019 WellBG 5800 User Guide V1.3
36/50
Welltech Computer Co., Ltd.
Boarder Gateway 5800 - 36 -
Filed Description: Get Log: Get Debug logs (-1~999). Zero indicates get log real
time. Clear: Clear logs
Ping
You can use the Ping to check an IP is active or not.
Start Path: Monitor > Ping
Figure 5.8-1Field Description: Host IP Address: The IP address to ping
8/12/2019 WellBG 5800 User Guide V1.3
37/50
Welltech Computer Co., Ltd.
Boarder Gateway 5800 - 37 -
Chapter 6 Telnet & RS-232 Configuration
Boarder Gateway 5800 also can support to be managed byTelnet or Console port (RS-232) for basic operations.
Interface: Network: TCP/IP Telnet (e.g. telnet 192.168.111.161
10086) RS232:
-Connect using: COM1-Baud Rate: 9600-Data bits: 8-Parity: None-Stop bits: 1-Flow Control: None-Wire: Null modem line (crossed)
Logon Boarder Gateway 5800 by Telnet
Use Windows build-in Hyper Terminal or other telnet termi-nal emulator to login (e.g. telnet 192.168.67.1:10086). User ID &password will be required for login (default login user id: admin,password: admin & user id: root, password: root).
Command List:
Command Description
echo Auto echo on or off
eventlog Clean or show system log messageexit Quit the current sessionipconfig Configure or show network1,2 informationping Check an IP address is available or notreboot Rebootreset Soft-resetshutdown Shutdowntime Reset or show system time.timezone Setup or show system time zoneuseradmin Manage user account.
Help &? View command list
Echo: auto echo on or not
Command Purpose
[root#]echo ? Usage: echo on/off
8/12/2019 WellBG 5800 User Guide V1.3
38/50
Welltech Computer Co., Ltd.
Boarder Gateway 5800 - 38 -
Example: echo on[root#]echo on Echo is on[root#]echo off Echo is off (default value)
Eventlog: show system log message
Command Purpose[root#]eventlog ? Usage: eventlog [-clear]
Example: eventlogeventlog -clear
[root#]eventlog Show system eventlog:Eventlog example:Time: 2003-06-19 20:15:17Event ID: 8700Type: WarningSource : wellgate5x00Description:[0] evt: TRUNK ALARM: TrunkId=3
Time: 2003-06-19 20:15:17Event ID: 8700Type: WarningSource : wellgate5x00Description:[0] evt: TRUNK ALARM: TrunkId=2
Time: 2003-06-19 20:15:14Event ID: 9501Type: InformationSource : wellgate5x00
Description:[0] evt: BOARD STARTED: SLOT:8Press any key to continue or press 'Q' to quit
[root#]eventlog-clear
Clear all event log
Exit: Quit the current session
Command Purpose
[root#]exit Quit the current session
Ipconfig: Configuration or show network information
Command Purpose
[root#] ipconfig ? Usage: ipconfig [-network boardno][-delete dns] [-dhcp] [-dns IPAd-dress1 IP
Address2] [-ip IP Address -mask Mask-gateway Gateway]
8/12/2019 WellBG 5800 User Guide V1.3
39/50
Welltech Computer Co., Ltd.
Boarder Gateway 5800 - 39 -
Example: ipconfig -network 1 -ip192.168.67. 1 -mask 255.255.0.0-gateway 192.168.5.254example : ipconfig -network 1 -dhcpexample: ipconfig -network 1 dns
192.168.1.1example : ipconfig -network 1 -delete
dns[root#]ipconfig Show current network conf iguration
[Network 1] Local Area ConnectionUSE FIXED IP (or DHCP)
IP Address : 192.168.5.7Subnet Mask : 255.255.0.0Default Gateway: 192.168.5.254DNS Servers :
[Network 2] Local Area Connection2USE FIXED IP
IP Address : 192.168.5.8Subnet Mask : 255.255.0.0Default Gateway :DNS Servers :
[root#]ipconfig net-work 1 delete dns
Delete the DNS servers setting[Network 1] Local Area Connection
USE FIXED IPIP Address :192.168.5.113Subnet Mask : 255.255.0.0
Default Gateway : 192.168.1.254DNS Servers :
[root#]ipconfig net-work 1dhcp
Enable DHCP[Network 1] Local Area Connection
USE DHCPIP Address : 192.168.5.10Subnet Mask : 255.255.0.0Default Gateway : 192.168.1.254DNS Servers : 192.168.5.1
168.95.1.1[root#]ipconfig net-work 1ip 61.220.12628 mask255.255.0.224gateway61.220.126.1
Use fixed network configuration[Network 1] Local Area Connection
USE FIXED IPIP Address : 61.220.126.28Subnet Mask : 255.255.255.1Default Gateway : 61.220.126.254
8/12/2019 WellBG 5800 User Guide V1.3
40/50
Welltech Computer Co., Ltd.
Boarder Gateway 5800 - 40 -
DNS Servers :[root#]ipconfig net-work 1ip61.220.126.115
Changes IP address only.[Network 1] Local Area Connection
USE FIXED IPIP Address : 61.220.126.115
Subnet Mask : 255.255.255.1Default Gateway : 61.220.126.254DNS Servers :
[root#]ipconfig net-work 1dns210.59.126.53
Changes DNS configuration only.[Network 1] Local Area Connection
USE FIXED IPIP Address : 61.220.126.115Subnet Mask : 255.255.255.1Default Gateway : 61.220.126.254DNS Servers : 210.59.126.53
Ping: Check an IP address is available or not
Command Purpose
[root#] ping ? Usage: ping IP.Example: ping 127.0.0.1
[root#]ping61.220.126.1
Ping resultReply from 61.220.126.1 bytes=64
time=1ms TTL=29Reply from 61.220.126.1 bytes=64
time=1ms TTL=29Reply from 61.220.126.1 bytes=64
time=1ms TTL=29Reply from 61.220.126.1 bytes=64
time=1ms TTL=29
Reboot:
Command Purpose
[root#] reboot ? Reboot SystemAre You Sure? (Y/N)
[root#]rebootAre You Sure?(Y/N)y
WellBG 5800 are rebooting
Shutdown:Command Purpose
[root#] shutdown ? Shutdown SystemAre You Sure? (Y/N)
[root#]shutdown WellBG 5800 are shut ting down
8/12/2019 WellBG 5800 User Guide V1.3
41/50
Welltech Computer Co., Ltd.
Boarder Gateway 5800 - 41 -
Are You Sure?(Y/N)y
Reset:
Command Purpose
[root#] reset ? Soft reset System
Are You Sure? (Y/N)[root#]resetAre You Sure?(Y/N)y
Time: Reset or show system time
Command Purpose
[root#] time ? Usage : time YYYY-MM-DDHH:NN:SS
Example : Time 2002-01-01 12:00:00[root#]time Show current time
The current time is 2003-06-20 15:17:30[root#]time2003-07-29 23:14:53
Change system b ios time
Timezone: Setup or show system timezone
Command Purpose
8/12/2019 WellBG 5800 User Guide V1.3
42/50
Welltech Computer Co., Ltd.
Boarder Gateway 5800 - 42 -
[root#] time-zone ?
Fixed Zone List :01. Afghanistan Standard Time03. Arab Standard Time05. Arabic Standard Time07. AUS Central StandardTime09. Azores Standard Time11. Cape Verde Standard Time13. Cen. Australia StandardTime15. Central Asia StandardTime17. Central European Stan-dard Time19. Central Standard Time21. Dateline Standard Time23. E. Australia Standard Time25. E. South America Standard
Time27. Egypt Standard Time29. Fiji Standard Time31. GMT Standard Time33. Greenwich Standard Time35. Hawaiian Standard Time37. Iran Standard Time39. Korea Standard Time41. Mexico Standard Time 243. Mountain Standard Time45. N. Central Asia StandardTime
47. New Zealand StandardTime49. North Asia East StandardTime51. Pacific SA Standard Time53. Romance Standard Time55. SA Eastern Standard Time57. SA Western Standard Time59. SE Asia Standard Time61. South Africa StandardTime63. Taipei Standard Time65. Tokyo Standard Time67. US Eastern Standard Time69. Vladivostok Standard Time71. W. Central Africa StandardTime73. West Asia Standard Time75. Yakutsk Standard Time
02. Alaskan Standard Time04. Arabian Standard Time06. Atlantic Standard Time08. AUS Eastern StandardTime10. Canada Central StandardTime12. Caucasus Standard Time14. Central America Stan-dard Time16. Central Europe StandardTime18. Central Pacific StandardTime20. China Standard Time22. E. Africa Standard Time24. E. Europe Standard Time
26. Eastern Standard Time28. Ekaterinburg StandardTime30. FLE Standard Time32. Greenland StandardTime34. GTB Standard Time36. India Standard Time38. Israel Standard Time40. Mexico Standard Time42. Mid-Atlantic StandardTime
44. Myanmar Standard Time46. Nepal Standard Time48. Newfoundland StandardTime50. North Asia Standard Time52. Pacific Standard Time54. Russian Standard Time56. SA Pacific Standard Time58. Samoa Standard Time60. Singapore Standard Time62. Sri Lanka Standard Time64. Tasmania Standard Time66. Tonga Standard Time68. US Mountain StandardTime70. W. Australia StandardTime72. W. Europe Standard Time74. West Pacific StandardTime
8/12/2019 WellBG 5800 User Guide V1.3
43/50
Welltech Computer Co., Ltd.
Boarder Gateway 5800 - 43 -
Usage1: timezone Zone (1 to 75) AutoDaylight (Y or N)Example1 : timezone 1 YUsage2 : timezone -custom Bias DaylightBias Day-lightStart StandardStart
Bias : -12:00 to +13:00DaylightBias : -12:00 to +13:00DaylightStart :
MM (Month: 01 to 12) ;WD (Day of week: 00 to 06)DD (Day:01 to 05 ;Specifies the occurrence of
day in the month;01 = First occurrence of day,02 = Second occurrence of day, ..., 05 = Last
occurrence of dayHH (Hour:00 to 23)
StandardStart :MM (Month: 01 to 12) ;WD (Day of week: 00 to 06)DD (Day:01 to 05 ;Specifies the occurrence of
day in the month;01 = First occurrence of day,02 = Second occurrence of day, ..., 05 = Last
occurrence of dayHH (Hour:00 to 23)
Example2 : timezone -custom +08:00 -01:00
04-00-01-02 10-00-05-02[root#]timezone Show current timezone infoTime Zone : (40) Mexico Standard Time (GMT -06:00)Daylight Bias : -01:00Daylight Start : 05-00-01 02:00Standard Start : 09-00-05 02:00Auto Daylight : Y
[root#]timezone40 n
Use pre-defined timezoneTime Zone: (40) Mexico Standard Time (GMT -06:00)Daylight Bias : -01:00Daylight Start : 05-00-01 02:00
Standard Start : 09-00-05 02:00Auto Daylight : n
8/12/2019 WellBG 5800 User Guide V1.3
44/50
Welltech Computer Co., Ltd.
Boarder Gateway 5800 - 44 -
[root#]timezone-custom +08:00-01:0005-00-01-0309-00-05-03
Use customized timezoneTime Zone : (99) Customized (GMT 08:00)Daylight Bias : -01:00Daylight Start : 05-00-01 03:00Standard Start : 09-00-05 03:00
Auto Daylight : Y
Useradmin: Manager User account
Command Purpose
[root#] useradmin ? Usage: useradmin [-add User][-delete User] [-password User]
Example: useradmin -add irene[root#]useradmin Show the current login user ac-
countroot
[root#]useradmin -list Show the current user accountlistadminrootIrene
[root#] useradmin -add irenePassword : ireneConfirm : irene
Add user Success.
Add the new user account: Irene
[root#] useradmin -delete1111
Are You Sure?(Y/N)y
Delete the user: 1111
[root#] useradmin -passwordrootNew Password : 1234Confirm : 1234
Change the user: roots pass-word.
8/12/2019 WellBG 5800 User Guide V1.3
45/50
Welltech Computer Co., Ltd.
Boarder Gateway 5800 - 45 -
Chapter 7 LCD Display Configuration
Boarder Gateway 5800 provides a front panel LCD for basicoperations.
Button List:Button List Description
When the WellBG 5800 is ready, the LCD screen shows asblow
Enter
Press Enter to select command
ESC Quit the current command Up or previous edit mode Next or previous edit mode
Command Tree:
Main Menu
Event Log Show system log message
Show IP Info
Use DHCPUse
IP ConfigNetwork 1Network 2
Fixed IP
YesReboot
No
Yes
Reset PWDNo
YesSoft Reset
No
Ready |04-03-03 16:40
Event Log
IP Confi
8/12/2019 WellBG 5800 User Guide V1.3
46/50
Welltech Computer Co., Ltd.
Boarder Gateway 5800 - 46 -
YesShut Down
No
Event Log:Configure LCD Display
Previous event log Next event logEnter Show detail event log Previous line Next lineESC Quit detail event log viewingESC Quit to main menu
IP Config:Configure LCD Display
Select Network1 or Network2 configuration
Select Network1 or Network2 configuration
Enter Configure Network1 or Network2
Select Network configuration Select Network configurationEnter Configure Network Increase the digit apply to network setting Decrease the digit apply to network settingEnter Apply change to network informationESC Quit network settingESC Quit to main menu
Reboot:
Configure LCD Display
Select Reboot or not Select Reboot or notEnter Reset user: roots (or admin) user passwordESC Quit Reboot configureESC Quit to main menu
Reset:
Configure LCD Display
Select user to change password Select user to change password
8/12/2019 WellBG 5800 User Guide V1.3
47/50
Welltech Computer Co., Ltd.
Boarder Gateway 5800 - 47 -
Enter Change user password Increase the alphabet apply to user password setting Decrease the alphabet apply to user password settingESC Quit Reset configureESC Quit to main menu
Soft Reset:
Configure LCD Display
Select Reset or not Select Reset or notEnter Reset or notESC Quit Reset configureESC Quit to main menu
Shutdown:
Configure LCD Display Select Shutdown or not Select Shutdown or notEnter Shutdown or notESC Quit Shutdown configureESC Quit to main menu
8/12/2019 WellBG 5800 User Guide V1.3
48/50
Welltech Computer Co., Ltd.
Boarder Gateway 5800 - 48 -
Appendix 1 Time zone to Country MappingList
Greenwich Mean Time & Country List Time Zone(GMT-12:00) International Date LineWest
21. Dateline Standard Time
(GMT-11:00) Midway Island, Samoa 58. Samoa Standard Time
(GMT-10:00) Hawaii 35. Hawaiian Standard Time
(GMT-09:00) Alaska 02. Alaskan Standard Time
(GMT-08:00) Pacific Time (US & Can-ada); Tijuana
52. Pacific Standard Time
(GMT-07:00) Mountain Time (US &Canada)
43. Mountain Standard Time
(GMT-07:00) Chihuahua, La Paz, Ma-zatlan
41. Mexico Standard Time 2
(GMT-07:00) Arizona 68. US Mountain Standard Time
(GMT-06:00) Saskatchewan10. Canada Central StandardTime
(GMT-06:00) Guadalajara, Mexico City,Monterrey
40. Mexico Standard Time
(GMT-06:00) Central Time (US & Can-ada)
19. Central Standard Time
(GMT-06:00) Central America14. Central America StandardTime
(GMT-05:00) Indiana (East) 67. US Eastern Standard Time
(GMT-05:00) Eastern Time (US & Can-ada)
26. Eastern Standard Time
(GMT-05:00) Bogota, Lima, Quito 56. SA Pacific Standard Time
(GMT-04:00) Santiago 51. Pacific SA Standard Time
(GMT-04:00) Caracas, La Paz 57. SA Western Standard Time
(GMT-04:00) Atlantic Time (Canada) 06. Atlantic Standard Time
(GMT-03:30) Newfoundland 48. Newfoundland Standard Time
(GMT-03:00) Greenland 32. Greenland Standard Time
(GMT-03:00) Buenos Aires, Georgetown 55. SA Eastern Standard Time
(GMT-03:00) Brasilia25. E. South America StandardTime
(GMT-02:00) Mid-Atlantic 42. Mid-Atlantic Standard Time
(GMT-01:00) Cape Verde Is. 11. Cape Verde Standard Time(GMT-01:00) Azores 09. Azores Standard Time
(GMT) Greenwich Mean Time: Dublin,Edinburgh, Lisbon, London
31. GMT Standard Time
(GMT) Casablanca, Monrovia 33. Greenwich Standard Time
8/12/2019 WellBG 5800 User Guide V1.3
49/50
Welltech Computer Co., Ltd.
Boarder Gateway 5800 - 49 -
(GMT+01:00) West Central Africa71. W. Central Africa StandardTime
(GMT+01:00) Sarajevo, Skopje, War-saw, Zagreb
17. Central European StandardTime
(GMT+01:00) Brussels, Copenhagen,Madrid, Paris
53. Romance Standard Time
(GMT+01:00) Belgrade, Bratislava,Budapest, Ljubljana, Prague
16. Central Europe Standard Time
(GMT+01:00) Amsterdam, Berlin, Bern,Rome, Stockholm, Vienna
72. W. Europe Standard Time
(GMT+02:00) Jerusalem 38. Israel Standard Time
(GMT+02:00) Helsinki, Kyiv, Riga, Sofia,Tallinn, Vilnius
30. FLE Standard Time
(GMT+02:00) Harare, Pretoria 61. South Africa Standard Time
(GMT+02:00) Cairo 27. Egypt Standard Time
(GMT+02:00) Bucharest 24. E. Europe Standard Time
(GMT+02:00) Athens, Istanbul, Minsk 34. GTB Standard Time
(GMT+03:00) Nairobi 22. E. Africa Standard Time
(GMT+03:00) Moscow, St. Petersburg,Volgograd
54. Russian Standard Time
(GMT+03:00) Kuwait, Riyadh 03. Arab Standard Time
(GMT+03:00) Baghdad 05. Arabic Standard Time
(GMT+03:30) Tehran 37. Iran Standard Time
(GMT+04:00) Baku, Tbilisi, Yerevan 12. Caucasus Standard Time
(GMT+04:00) Abu Dhabi, Muscat 04. Arabian Standard Time
(GMT+04:30) Kabul 01. Afghanistan Standard Time
(GMT+05:00) Islamabad, Karachi,
Tashkent
73. West Asia Standard Time
(GMT+05:00) Ekaterinburg 28. Ekaterinburg Standard Time
(GMT+05:30) Chennai, Kolkata, Mum-bai, New Delhi
36. India Standard Time
(GMT+05:45) Kathmandu 46. Nepal Standard Time
(GMT+06:00) Sri Jayawardenepura 62. Sri Lanka Standard Time
(GMT+06:00) Astana, Dhaka 15. Central Asia Standard Time
(GMT+06:00) Almaty, Novosibirsk 45. N. Central Asia Standard Time
(GMT+06:30) Rangoon 44. Myanmar Standard Time
(GMT+07:00) Krasnoyarsk 50. North Asia Standard Time
(GMT+07:00) Bangkok, Hanoi, Jakarta 59. SE Asia Standard Time
(GMT+08:00) Taipei 63. Taipei Standard Time
(GMT+08:00) Perth 70. W. Australia Standard Time
(GMT+08:00) Kuala Lumpur, Singapore 60. Singapore Standard Time
(GMT+08:00) Irkutsk, Ulaan Bataar49. North Asia East StandardTime
8/12/2019 WellBG 5800 User Guide V1.3
50/50
Welltech Computer Co., Ltd.
Boarder Gateway 5800 - 50 -
(GMT+08:00) Beijing, Chongqing, HongKong, Urumqi
20. China Standard Time
(GMT+09:00) Yakutsk 75. Yakutsk Standard Time
(GMT+09:00) Seoul 39. Korea Standard Time
(GMT+09:00) Osaka, Sapporo, Tokyo 65. Tokyo Standard Time
(GMT+09:30) Darwin 07. AUS Central Standard Time(GMT+09:30) Adelaide 13. Cen. Australia Standard Time
(GMT+10:00) Vladivostok 69. Vladivostok Standard Time
(GMT+10:00) Hobart 64. Tasmania Standard Time
(GMT+10:00) Guam, Port Moresby 74. West Pacific Standard Time
(GMT+10:00) Canberra, Melbourne,Sydney
08. AUS Eastern Standard Time
(GMT+10:00) Brisbane 23. E. Australia Standard Tim
(GMT+11:00) Magadan, Solomon Is.,New Caledonia
18. Central Pacific Standard Time
(GMT+12:00) Fiji, KamChapterka, Mar-
shall Is. 29. Fiji Standard Time(GMT+12:00) Auckland, Wellington 47. New Zealand Standard Time
(GMT+13:00) Nuku'alofa 66. Tonga Standard Time