What’s New from Raymarine? - National Marine - s New from Raymarine? Jim McGowan ... UP and...

What’s New from Raymarine?

Jim McGowan

US Marketing Manager

[email protected]

Multifunction Displays


*R70003 Video Cable necessary to expand from standard 1 In to 2 In / 1 Out

Product Line

Model Screen Size

Hybrid Touch

Hard Key Touch Only

Fish Finder

WiFi Bluetooth Video

a-Series a65 5.7” X X Over IP

a67 5.7” X X Over IP

c-Series

c95 9” X X X 1 In

c97 9” X X X X 1 In

c125 12” X X X 1 In

c127 12” X X X X 1 In

e-Series

e7 7” X X X 1 In

e7D 7” X X X X 1 In

e95 9” X X X 2 In / 1 Out*

e97 9” X X X X 2 In / 1 Out*

e125 12” X X X 2 In / 1 Out*

e127 12” X X X X 2 In / 1 Out*

E165 15.4” X X X 2 In / 1 Out*

Multifunction Displays What’s in the Box?

a65/a67

1. Sun cover

2. Front bezel

3. Multifunction display

4. Rear bezel

5. Flush mount gasket

6. Screw pack, includes:

• 4 x rear bezel fixing screws

• 4 x unit flush mount screws

• 4 x unit trunnion mount screws

7. Documentation pack, includes:

• Multilingual CD

• Installation and getting started guide

• Mounting template

• Warranty policy

8. 1.5 m (4.9 ft) power and data cable

9. Trunnion bracket


e7/e7D

1. Sun cover

2. Front bezel


4. Rear bezel



• 4 x rear bezel fixing screws


• 4 x unit trunnion mount screws


• Multilingual CD



• Warranty policy


9. Trunnion bracket


c9x/c12x/e9x/e12x/e165

1. Sun cover

2. Front bezel






• Multilingual CD



• Warranty policy


Multifunction Displays Product Dimensions

a65 / a67 e7 / e7D c9x / e9x c12x / e12x

A 6.45” (164mm) 9.17” (233mm) 11.42” (290mm) 13.94” (354mm)

B 5.66” (144mm) 5.67” (144mm) 6.81” (173mm) 8.74” (222mm)

C 2.79” (71mm) 2.52” (64mm) 2.52” (64mm) 2.72” (69mm)

D - 6.29” (160mm) 6.29” (160mm) 6.29” (160mm)

E - 7.09” (180mm) 8.35” (212mm) 10.08” (256mm)

Multifunction Displays Flush Mount Installation

Multifunction Displays Trunnion Mount Installation


Connection Ports

• Port #1: Transducer

• e7D, c97, e97, c127 & e127 Only

• Port #2: SeaTalkNG

• Port #3: Network/RayNet

• Port #4: Network/RayNet

• c9x, e9x, c12x & e12x Only

• Port #5: Video Port

• e9x & e12x Only

• 1 In / 1 Out

• Optional R70003 Cable Required

• Port #6: Power/Data/Video


Power / Data / Video Cable 1. MFD Ports

2. Power and data cable

3. Connection to 12/24 V power

• e7/e7D = 12V only

4. Red cable (positive)

5. Fuse

6. Black cable (negative)

7. Video input cable

• Female BNC

8. NMEA 0183 data cables

9. Shield (drain) wire

• Thin black wire; must be connected to RF ground point


Power / Data / Video Cable

• NMEA0183 Connections

Color Port Input/Output +/-

1 White 1 In +

2 Green 1 In -

3 Yellow 1 Out +

4 Brown 1 Out -

5 Orange/White 2 In +

6 Orange/Green 2 In -


MFD to VHF NMEA0183 Connections


MFD Direct Transducer Connection

(MFD w/ Built-In Sounder; c97, c127, e7D, e97, e127)

1. Rear connector panel of multifunction display

2. Sonar transducer cable

3. Sonar transducer


DSM30/DSM300 Style Transducer Connection

(MFD w/ Built-In Sounder; c97, c127, e7D, e97, e127)


2. DSM30/300 transducer adaptor cable (E66066)

3. Sonar transducer

E66066 DSM30/DSM300

Adaptor Cable

Multifunction Displays Bluetooth Connection

• Pairing the remote and configuring the

UP and DOWN buttons

• The remote control unit must be “paired”

with the multifunction display that you

want to control. On your multifunction

display, with the home screen displayed:

1. Select Set-up

2. Select System Settings

3. Select Connections

4. Select Bluetooth > On

5. Select New Bluetooth Connection • A pop-up message will be displayed to confirm

that the device you are connecting to is

discoverable

6. Select Ok to confirm

7. On your remote control unit, hold down the UP and DOWN buttons together for 10 seconds

8. Select OK to clear the on-screen message • A list of discovered devices is displayed

9. Select the remote control unit in the list of devices

10. When prompted, press the arrow button on your remote that you wish to be configured as the UP button. The other arrow button will automatically be configured as the DOWN button

• If the pairing was successful a “Pairing Success” message will be displayed. If a “Pairing Failure” or “Pairing Timeout” message is displayed, repeat steps 1 to 9

Multifunction Displays Bluetooth Connection

• Pairing a Media Player

• To use this feature you must first:

1. Enable Bluetooth in the System Settings

on the multifunction display

2. Enable Bluetooth on the media player

device

3. Pair the media player device with the

multifunction display

4. Enable Audio Control in the System

Settings on the multifunction display

NOTE: If your media player does not include

built-in speakers it may be necessary to

connect the media player’s audio output to

an external audio system or a pair of

headphones. For more information refer to

the instructions that accompany the media

player device.

Multifunction Displays Wi-Fi Connection

• Utilizing a Raymarine App

• To use this feature you must first:

1. Download and install the Raymarine

Viewer, Remote or Control app, available

from the Apple App Store or Google

Marketplace

2. Enable Wi-Fi in the System Settings on

the multifunction display 1. Home: Set-Up > System Settings > Wireless

Connections > Wi-Fi: ON

3. Enable the desired streaming capability

within the System Settings of the

multifunction display 1. RayViewer – Viewing Only

2. RayRemote – Remote Control

3. RayControl – Remote Control

4. Enable Wi-Fi on your smartphone or

tablet

5. Select the Raymarine Wi-Fi connection

from the list of available Wi-Fi networks

on your smartphone or tablet

Digital Sounder Modules


What’s in the Box

• DSM30

• DSM30

• Power Cable

• Mounting Screws

• Instruction Manual


What’s in the Box

• DSM300

• DSM300

• Power Cable

• Mounting Screws

• Instruction Manual

• Operation Manual


What’s in the Box

• CP450C

1. CP450C

2. Power Cable 1.5m

3. Document Pack

4. Fixing Screws


Product Dimensions (DSM30/DSM300)


Product Dimensions (CP450C)

A. 11.79” (300mm)

B. 8.06” (205mm)

C. 3.45” (88mm)

D. 3.15” (80mm)


DSM30/DSM300 Installation


CP450C Installation

Digital Sounder Modules Connection Ports

DSM30/DSM300

1. Transducer Port

2. HSB2 Port

3. Power

4. SeaTalkHS Port

NOTE: SeaTalkHS Cable, Crossover Coupler and RayNet to RJ45 Adaptor Cable required to connect DSM30/DSM300 to any new Raymarine MFD

CP450C

1. RayNet Network Port

2. Power

3. Transducer Port

NOTE: Connect 2 Transducers to the CP450C via the Transducer Y-Cable (A102146)

Digital Sounder Modules DSM30/DSM300/CP450 Sounder Module Connections


2. Sounder Module

3. RayNet cable

4. HS5 network switch

5. Sonar transducer cable

6. Sonar transducer

NOTE:

-Connection from HS5 to DSM30/300= SeaTalkHS, Crossover Coupler and RayNet to RJ45

-Connection from HS5 to CP450C is just RayNet to RayNet

Digital Sounder Modules CP450 Sounder Module Connections

Single CHIRP Transducer

Dual CHIRP Transducers w/ Y-Cable (A102146)

Single DSM Transducer w/ DSM30/DSM300 Style Transducer

Adaptor Cable (A102147) Note: DSM Ducers do not CHIRP

Digital Sounder Modules CP450 Sounder Module Connections

Direct MFD Connection

1. CP450C

2. RayNet to RayNet Cable

3. New c/e-Series MFD

HS5 Network Connection

1. CP450C

2. New c/e-Series MFD

3. RayNet to RayNet Cable

4. HS5 Network Switch

Digital and HD Color Radar

Digital and HD Color Radar What’s in the Box?

Digital and HD Color Radomes (RD418D / RD418HD / RD424D / RD424HD)

1. Radome

2. Mounting Hardware

3. Denso Paste

4. Installation Template

Radome Packs also include the

following:

1. 10m Digital Radar Cable

2. Crossover Coupler

3. 1.5m SeaTalkHS Cable

Digital and HD Color Radar What’s in the Box?

HD and Super HD Pedestals 1. Pedestal

2. Mounting Template

3. Denso Paste

4. VCM100

5. VCM100 Cable Clamp

6. Lifting Eye (3)

7. Stud (4)

8. Plain Washer (4)

9. Spring Washer (4)

10. Nut (4)

11. VCM100 Mounting Screw

12. VCM100 Cable Clamp Mounting Screw

HD and Super HD Arrays 1. Array

2. Mounting Nuts (4)

Digital and HD Color Radar Product Dimensions

18” Radomes 24” Radomes

(RD418D/RD418HD) (RD424D/RD424HD)


Product Dimensions


Radome Installation


Open Array Installation


Open Array Installation


Radar Connection Using a

Crossover Coupler

1. Digital radar scanner

2. Multifunction display rear

connector panel

3. SeaTalkHS crossover

coupler

4. RayNet to RJ45 cable

5. Connection to power

supply

• Open array scanners require

a Voltage Converter Module


Radar Connection Using a HS5 Network Switch

1. Digital radar scanner

2. HS5 network switch

3. RayNet cable

4. RayNet to RJ45 cable

5. SeaTalkHS crossover coupler

6. Voltage Converter Module

• Required for Open Arrays

7. Power connection

Instruments

Instruments

What’s in the Box?

i40

1. i40 Instrument

2. Sun Cover

3. Gasket

4. Clamping Bracket

5. Fixing Stud/Thumb Nut

6. SeaTalk Power Cable

7. Document Pack

Instruments

i40 Product Dimensions

A. 5.04” (128mm)

B. 2.83” (72mm)

C. 2.17” (55mm)

D. 0.70” (18mm)

E. 0.67” (17mm)

F. 1.18” (30mm)

2.17” (55mm) Circular Cutout

Instruments

i40 Installation

Instruments

i40 Speed Transducer Connection

1. Temp OV (Brown)

2. Temp Signal (White)

3. Speed OV (Gray)

4. Speed Signal (Green)

5. Speed V+ (Red)

Instruments

i40 Depth Transducer Connection

1. Speed – (Black)

2. Speed + (Blue)

3. Power OV (Gray)

Instruments

i40 BiData Transducer Connection


2. Speed + (Blue)

3. Power OV (Gray)

4. Temp OV (Brown)


6. Speed OV (Gray)


8. Speed V+ (Red)

Instruments

i40 Wind Transducer Connection

1. Rotor + (Red)

2. Rotor – (Blue)

Instruments i40 SeaTalk System

1. i40 Depth Instrument

2. i40 Speed Instrument

3. I40 Wind Instrument

4. Rotavecta Transducer

5. Depth Transducer

6. Speed Transducer

7. 12V Power Supply

Instruments i40 SeaTalkNG System

1. i70 Instrument

2. 12V Power Supply

3. SeaTalkNG 5-Way Block

4. SeaTalk to SeaTalk NG Converter

5. SeaTalk 3 Way Block



8. I40 Wind Instrument

9. Depth Transducer

10. Speed Transducer

11. Rotavecta Transducer

NOTE: 5-Way Block and Converter are missing SeaTalkNG Blanking Plugs in unused connection points. These should be used to prevent water intrusion

Instruments


i50/i60

1. i50/i60 Instrument

2. Front Bezel

3. SeaTalk to SeaTalkNG

Cable

4. SeaTalkNG Spur

5. Gasket

6. Sun Cover

7. Document Pack

8. SeaTalkNG Blanking Plug

9. 4 Mounting Screws

Instruments


i70

1. i70 Instrument

2. Front Bezel

3. Gasket

4. Sun Cover

5. 4 Mounting Screws

6. Document Pack


8. SeaTalkNG Spur

Instruments

i50/i60/i70 Product Dimensions

A. 4.53” (115mm)

B. 4.30” (110mm)

D. 0.55” (14mm)

E. 1.18” (30mm)

F. 0.67” (17mm)

G. 3.54” (90mm)

H. 0.98” (25mm)


Instruments

i50/i60/i70 Installation

Instruments

i50 Speed

1. Temp OV (Brown)


3. Speed OV (Gray)


5. Speed V+ (Red)

Instruments

i50 Depth


2. Speed + (Blue)

3. Power OV (Gray)

Instruments

i50 TriData


2. Speed + (Blue)

3. Power OV (Gray)

4. Temp OV (Brown)


6. Speed OV (Gray)


8. Speed V+ (Red)

Instruments

i60 Wind

1. Rotor + (Blue)

2. Rotor – (Red)

3. Wind OV (Gray)

4. Anemometer Signal (Yellow)

5. Cosine Wind Direction (Blue)

6. Sine Wind Direction (Green)

7. Wind V+ (Red)

#1-2 = Rotavecta

#3-7 = Wind Transducer

Instruments

i70 Multifunction Instrument

• SeaTalkNG Connectivity

1. 12V Power Supply

2. SeaTalkNG Backbone

3. DeviceNet Cable

1. SeaTalkNG to NMEA2000

Instruments i50/i60/i70 SeaTalkNG System

1. i70 Instrument

2. p70R Control Head

3. i60 Wind Instrument

4. Wind Transducer

5. Raymarine MFD

6. 12 / 24V Power Supply

7. Raymarine Course Computer



10. Depth Transducer

11. Speed Transducer

iTC-5 Transducer Converter

iTC-5 Transducer Converter

Item Description

1 Red - Speed and sea temperature transducer connection

2 Orange - Wind transducer and rotavecta connection

3 Yellow - Fluxgate compass connection

4 Green - Rudder reference transducer connection

5 Blue - Depth transducer connection

6 SeaTalkng backbone connection

7 SeaTalkng spur connection

8 Sea Talkng backbone connection

Basic iTC-5 System

Autopilots

Autopilots


p70 / p70R

1. p70/p70R Control Head

2. Bezel

3. Gasket

4. Sun Cover

5. 4 Fixing Screws

6. Documentation Pack


8. SeaTalkNG Spur

Autopilots

p70/p70R Product Dimensions

A. 4.30” (110mm)

B. 4.53” (115mm)

C. 0.55” (14mm)

D. 1.18” (30mm)

E. 1.38” (35mm)

F. 3.54” (90mm)

G. 0.67” (17mm)

H. 0.81” (21mm)


Autopilots

p70/p70R Product Installation

Autopilots

p70/p70R Product Installation

Autopilots What’s in the Box?

SPX Core Pack 1. Course Computer

2. SeaTalkNG Spur (1m)

3. SeaTalkNG Backbone Cable (400mm)

4. SeaTalkNG T-Piece

5. Fluxgate Compass

6. Mounting Screws and Cable Ties

7. Documentation Pack

8. Rudder Reference*

9. Ball Joint Cap*

10. Ball Joint*

11. Rudder Ref Mounting Screws*

12. M6 Threaded Bar*

* Not Supplies with the SPX-10

Autopilots

Product Dimensions

Autopilots

SPX Course Computer Product Installation

Autopilots

SPX-10 / 30 Course Computer Connections

1. SeaTalkNG

2. NMEA0183 In/Out (4800 baud rate)

3. Sleep Switch Connection

4. Power In

5. Drive Power Out

6. RF Ground

7. SeaTalk

8. Fluxgate Compass

9. Rudder Reference

10. Drive Clutch

Autopilots

SPX-SOL Course Computer Connections

1. SeaTalkNG

2. NMEA0183 In/Out (4800 baud rate)

3. Sleep Switch Connection

4. Power In

5. Solenoid A/B Drive

6. Solenoid A/B Return

7. RF Ground

8. SeaTalk

9. Fluxgate Compass

10. Rudder Reference

11. Bypass Valve

Autopilots SeaTalk Autopilot System

1. p70 Control Head

2. Depth Instrument

3. Speed Instrument

4. Wind Instrument

5. Wind Transducer

6. SeaTalk to SeaTalkNG Cable

7. Depth Transducer

8. Speed Transducer

9. Course Computer

NOTE: Course Computer is supplying 12V power to the SeaTalk Network

NOTE: Fluxgate Compass would connect directly to the Course Computer

Autopilots SeaTalkNG Autopilot System

1. i70 Instruments

2. p70 Control Head

3. Course Computer

4. SeaTalkNG 5-Way Connector

5. Rudder Reference

6. Fluxgate Compass

7. Transducer Pods

8. Wind Transducer

9. Speed Transducer

10. Depth Transducer

NOTE: Transducer Pods can be replaced with the all-in-one ITC-5 Converter

Thermal Cameras

Thermal Cameras


T300/T400 Series

1. T-Series Thermal Camera

2. Mounting Fasteners

3. SeaTalkHS Coupler

4. Large O-Ring

5. Small O-Ring

6. Female to Female Coaxial

Connector

7. Female Coaxial to Male

BNC Connector

8. Female BNC to Male RCA

Thermal Cameras Product Dimensions

Thermal Cameras Product Dimensions

Thermal Cameras

T-Series Connections

1. Power / Drain

2. IR Out (Thermal)

3. SeaTalkHS

4. VIS / IR Out (Low

Light/ Thermal)*

5. Low Impedance

Ground

*Only Available on 400

Series Thermal Cameras

Thermal Cameras

T-Series Connection

1. Rear panel of MFD

2. Video Accessory Cable

(R70003)

3. BNC Video Connector

4. Thermal Camera

NOTE: T-Series Video

connections are Male Coaxial,

Female Coaxial to Male BNC

Adaptor is required for direct

connection to MFD Video

Accessory Cable

Thermal Cameras

T-Series Installation

Thermal Cameras

T-Series Installation w/ JCU 1. Thermal Camera

2. SeaTalkHS Switch

3. SeaTalkHS Coupler

4. Joystick Control Unit

5. POE Injector

6. SeaTalkHS to Other Device

POE Injector

1. POE Injector

2. Ethernet/Power Cable

3. JCU

4. Power to POE Injector

5. SeaTalkHS Connection

Thermal Cameras

Cables and Accessories


RayNet Network Cables

• Improved cabling system for SeaTalkHS Data

• Same data as SeaTalkHS, Different Connector

• Benefits over SeaTalkHS

• Fully waterproof connection

• Smaller diameter

• Provision for faster data speeds

• Easily integrated with SeaTalkHS Accessories

via the RayNet to RJ45 Adaptor Cables

• A62360: RayNet to RJ45 - 1m



• Connect multiple components with the HS5

Network Switch

RayNet Cable

RayNet to RJ45


HS5 Network Switch

• Replaces the SeaTalkHS Network Switch

• Connection Ports • 1 SeaTalkNG Power Cable Port

• 5 RayNet Network Ports

• Supported Network Speeds • 10 Mbit/sec

• 100 Mbit/sec

• 1000 Mbit/sec (5th port only)

• Gigabit 5th port allows higher speed across switches, should a 2nd switch be necessary

• 12V or 24V DC

MFD Mounting Adaptor Kits

• Upgrade from C/E-Classic or C/E-Wide without cutting

• Kit consists of the following:

• Adaptor Steel Plate

• Adaptor Bezel

• Mounting Hardware


Current MFD New MFD Adaptor Kit

C90W/E90W c9x/e9x R70008

C120W/E120W c12x/e12x R70009

C80/E80 Classic c9x/e9x R70010

C120/E120 Classic c12x/e12x R70011

E80 Classic

e97 with R70010 Adaptor Bezel Kit


RS130

• 48-channel GPS receiver with

WAAS, EGNOS and MSAS

Satellite Differential decoding

• SeaTalkNG and NMEA2000

Compatible

• Ideal for below-deck

installations or redundancy

• Includes a 1” x 14 TPI pole

mounting adapter

Cables and Accessories Part Number Description R70001 c/e-Series - Trunnion Kit / 9" disp

R70002 c/e-Series - Trunnion Kit / 12" disp

R70027 c/e-Series - Rear Bezel /9" disp

R70028 c/e-Series - Rear Bezel /12" disp

R70008 Mounting Adaptor Kit - C90W/E90W

R70009 Mounting Adaptor Kit - C120W/E120W

R70010 Mounting Adaptor Kit - C80/E80

R70011 Mounting Adaptor Kit - C120/E120

A80007 HS5 SeaTalkHS Network Switch

A62360 RayNet to RJ45M - 1m

A80151 RayNet to RJ45M - 3m

A80159 RayNet to RJ45M - 10M

A80161 RayNet to RayNet – 400mm (Male/Male) A62361 RayNet to RayNet - 2m

A80005 RayNet to RayNet - 5m



R70014 RayNet cable puller - 5 pack

R32142 Coupler Ethernet Waterproof R70003 e-Series Accessory Video Cable

R70029 Power/Data/Video Cable, 1M – angled

A62363 Minnkota adaptor cable 1M

E66066 DSM30/DSM300 Transducer Adaptor Cable

E62351 RCU-3 Bluetooth Remote

Date post:	28-Mar-2018
Category:	Documents
Upload:	vuongkhanh
View:	218 times
Download:	3 times

What’s New from Raymarine? - National Marine - s New from Raymarine? Jim McGowan ... UP and...

Documents