Date post: | 08-Apr-2018 |
Category: |
Documents |
Upload: | kevins-small-engine-and-tractor-service |
View: | 225 times |
Download: | 1 times |
8/7/2019 WheelHorse light panel assembly manual 8-8012
http://slidepdf.com/reader/full/wheelhorse-light-panel-assembly-manual-8-8012 1/5
PARTS LIST AND INSTRUCTIONS
WHEELHORSEPRODUCTS,INC. • SOUTH BEND,IND.
DESCRIPTION
The Model 8-0812 l ight Panel Accessory fits th eshort frame, vertical shaft, and Lawn Ranger Model1-8745.
FOR SHORT FRAME AN D VERTICAL SHAFT TRAC-TORS USE INSTRUCTIONS ON PAGE 1 AN D 2.LAWN RANGER INSTRUCTIONS BEGIN ON PAGE 2.
ASSEMBLY
1. IMPORTANT: Disconnect th e battery groundcable from th e battery. This will prevent hot sparksan d shorts.
Figure 1
ASSEMBLYLIGHTPANEL ACCESSORY
MODEL8·08122. On th e short frame models th e fuel tank must
be moved to expose th e rear of th e dash panel.
A. Loosen screw on the tank strap.B. Slide the tank forward and to th e right side
of the tractor.
Figure 2
3. Remove th e plastic plug button in th e switchhole by hitting th e plastic stems off with a screwdriver tip.
4. Connect the red wire of the light harness andthe red tail light wire to th e center terminal of th eswitch. The fused wire on the harness is connected
to the side terminal. (See Fig. 1 an d Wiring Diagrams.)5. String wires through th e switch hole an d down
through the rubber grommet. (See Fig. 2.)
Figure 3
6. The green fused wire is connected to the battery positive terminal.
7. The hood escutcheon plate can be removed bybreaking off th e stems with a screwdriver tip. Installth e tw o Ya rivets through th e hood an d reflector housing. The rivets ar e held in place with th e push-onnuts, th e slotted en d of th e nu t goes on the rivet first,se e Fig. 4 and th e Exploded View DrawilJg.
8/7/2019 WheelHorse light panel assembly manual 8-8012
http://slidepdf.com/reader/full/wheelhorse-light-panel-assembly-manual-8-8012 2/5
Figure 4
Figure 5
8. Insert th e socket wires, springs, and bulbs asshown in Fig. 4.
9. Mount the lens to the opening and fasten withthe four machine screws as shown in Fig. 5.
Figure 6
Figure 7
10. String th e red wire of the harness forwardunder th e left side of the engine and along the leftside of th e hood. Connect th e wire leads to th e connector as shown in Fig. 6. Fasten the wire to th ehood with th e clips provided. Any excess wire canbe looped and taped to th e inside of th e hood.
11. Mount tail light base to th e rear of the fenderas shown in Fig. 7.
12. String th e red tail light wire down inside th ehoodstand (stay behind lift ar m shaft) and back inside the tool box. Connect th e black tail light wireto th e red lead from th e switch with th e connector asshown in Fig. 8.
13. Mount fuel tank back in position. Connectbattery ground cable, an d tr y lights. If lights fail tocome on - check wiring - se e diagrams. The groundfor th e lights is transmitted through the hood latchrod; therefore, the lights may go ou t when the hoodis up.
Figure 8
INSTRUCTIONSLAWN RANGER MODEL 1·8745
ASSEMBLY
1. IMPORTANT: Disconnect the battery groundcable from the battery. This will prevent ho t sparksan d shorts.
2. Drill holes in th e rear of seat pan. (See Fig. 1.)Drill three
~ 2 Dia. holes a t th e locations shown.
Figure 1
- 2 -
8/7/2019 WheelHorse light panel assembly manual 8-8012
http://slidepdf.com/reader/full/wheelhorse-light-panel-assembly-manual-8-8012 3/5
3. Mount th e tail light to th e seat pa n with th e
# 10 screws, lockwashers, and nuts as shown in Fig.2. The 6" black ground wire fits under th e nut of
screw marked "A" to under th e nu t of screw marked"8". (See Fig. 2.)
Figure 2
4. Insert th e wires, springs, and bulbs in th e re-flector housing. Using th e four #6-32 screws mount the
lens and th e reflector housing to th e grill as shown in
Fig. 3. Slip one end of the 13)1" black ground wire
under th e lip of the housing an d connect th e otheren d to on e of the grill hinge bolts as shown. Attach
th e double connector to the black lead wires from th e
housing.
Figure 3
5. Connect the fused green wire of the harnessto th e positive terminal of the battery. (See Fig. 4.)
Run the red wire forward and under the wire clipprovided on the engine as shown. Connect this wireto th e connector, and fasten it to th e side of the grillwith th e wire clips. (See Fig 4.)
Figure 4
Slip th e tw o remaining ends of the wire harness
through the hole at th e base of the battery into th edash area.
6. Use a screwdriver to pry off th e plug button
covering the switch opening. (See Fig. 5.)
Pull th e wire leads of the harness through th eopening.
Figure 5
Connect th e loose re d tail light wire to th e tail
light with th e connector provided. Run th e wire un-
de r th e seat pan to th e dash area and up throughth e switch opening. Cut off th e excess length of the
tail light wire to allow about 5" through the open
ing. Skin the end of the wire and fasten the spadeterminal provided.
Connect th e tw o red leads to th e center terminalof th e switch and th e green to th e en d terminal asshown.
7. Install th e switch into the opening. Reconnectth e battery ground cable and try the switch, it ma y
have to be pulled ou t and rotated to correspond to
th e off and on position marked on the dash.
- 3 -
8/7/2019 WheelHorse light panel assembly manual 8-8012
http://slidepdf.com/reader/full/wheelhorse-light-panel-assembly-manual-8-8012 4/5
LIGHTS
ow""
ow""
GREEN
LIGHT SWITCH
I,
Wiring Diagram TAIL LIGHT
Short Frame and Vertical Shaft Tractors
PARTS LIST LIGHT PANEL
#8-0812(Specificotions subject to chong8 wi,hout notice.)
Parts available only through Authorixed Dealers.When ordering parts always list Part No . an d name of Part.
Item Part Na.No. No. Description Req'd .
7223 Reflector an d Socket2 7226 Wire - Light Socket 23 7227 Spring 24 7228 Bulb <#1156) 2
5 7075 lens 16 8279 Screw Self Tap #6-32 x % Special 47 100074 Terminal Spade
8 7184 Switch9 9894 Wir e - H ea dl ig ht Ground
10 7185 Wire Harne .. 111 3023 Clip 712 7618 C on ne ct or - 3 -Way 113 923003 Rivet Ys x
%Flat Head
214 7429 Nut Ys Dia . 215 8041 Base16 B042 lens 117 8043 Bulb 12 Volt 218 8044 P ad - Mo unt in g 119 909138-4 Bolt - Round Head # 10-32 x % 220 915551·4 Nut - Hex # 10-32 221 920079-4 Lockwasher # 222 6922 Connector - 2 -Wa y23 7574 Wire - Tail Light - Green24 9895 Wire - Ground Tail Light
Printed in U. S. A.
- 4 -
Wiring DiagramLawn Ranger Lawn Tractor
9
5-12-69 FORM NO . 327A
8/7/2019 WheelHorse light panel assembly manual 8-8012
http://slidepdf.com/reader/full/wheelhorse-light-panel-assembly-manual-8-8012 5/5
GREEN
ItemNo. No. Description Req'd.
7223 Reflector an d Socket 17226 Light 2
3156) 2
#6-32 47 100074 Terminal Spade
71849 H"adlight Ground
10
Connector 3-Way 1923003 27429 2
16 804217 2
19 22
920079-4222324
U. S. A.NO. A-SI92