7/23/2019 Wheelloader i e a4

1/7

Special Vehicle Series :01

AssemblyInstructionsWheel Loader

http://www.canon.com/c-park/en/

View of completed model

* This model was designed for Papercraft andmay differ from the original in some respects.

Tools Assembly tip

Key to symbols

ScissorsRuler, set squareGlue (Wood glue or craft glue recommend)Exhausted ballpoint pen (out of ink)Toothpicks (for use in applying glue)

Tweezers (useful for handling small parts)Pencil

Write the number of each part on the reverse side of the part in pencil

upon cutting it out, to be sure you can tell which part is which later.

Before gluing, crease the paper along

mountain and valley fold lines. Trace along

the folds with a ruler and an exhausted

ballpoint pen (out of ink) to get a sharper fold.Make sure rounded sections are nice and stiff.

Pattern

Red dot

Green dot

Blue dot

Assembly instructions

Solid line

Dashed anddotted line

Dotted line

Solid red line

Diagonalgrey lines

Mountain foldFold so that the printedpattern faces outside.

Fold so that the printedpattern faces inside.

Valley fold

Cut parts outalong this line.

Cut a notchalong this line.

Cut these areasout.

The dots show where to gluethe pieces together. Glue thepieces together as shown in thefollowing examples.Some parts must be gluedtogether along the cut surfaces.

Glue parts with the samenumber together. (Numbers arenot printed on very small parts.)

Glue areas within the samepart together.

Glue to the reverse side of thespecified part.

This denotes a partthat must be able tomove after the modelis completed. Be sureto crease these partssufficiently.

Glue

Insert

Glue tab

Reverse side ofpaper

Movable part

(without gluing)

Red arrow

Blue arrow

Light blue

Light grey

Glue, scissors and other tools may be dangerous to young childrenso be sure to keep them out of the reach of young children.

Assembly Instructions: Seven A4 sheets (No. 1 to No. 7)Build this model with careful reference to the Assembly Instructions.

7/23/2019 Wheelloader i e a4

2/7

Assembly InstructionsWheel Loader

Assemble the cab.Glue flaps a and b in order.

Use care to get the shape rightwhen assembling this part,referring to the cross sectionat right.

Cross section

Close this surface last and glue it in place.

Glue flaps a, b, and c in order.

7/23/2019 Wheelloader i e a4

3/7

Glue flaps a, b, c, d, and ein order. Leave an opening here.

Shape this part before gluing it.

This is a moving part.Do not glue it.

Glue flaps a, b, and c in order.

Glue to part G.Use care to attach this partin the right direction,referring to the illustration.

Fold the left and right flapsback and glue each in place.

Use care with the angles at which you glue parts12 and 13 in place, to ensure the two parts are parallel.

Cross section

Cross section

Moving part

Moving part

Moving part

Fold down the sides, then bendthe center down along the curvededges and glue it in place.

Apply a small amount ofglue to the cut surface ofthe paper as well, and gluethis part in place alongwith the shape of thebucket. (The bucket doesnot have any glue tabs.)

Glue the back sides of the paperparts together, in numbered order.Fold in the ends of parts 22 and

28 and then glue them in place.

Glue parts 17 and 18 tothe reverse side of the bucket.

Reverse side

Assembly InstructionsWheel Loader

7/23/2019 Wheelloader i e a4

4/7

Glue flaps a and b in order.

Insert into the openingin part F.

Referring to the cross section,insert this part through the holes andfix it in position at top and bottom.

Cross section

Overhead view

This is the joint betweenthe front and rear sections.

Assemble in the same way as part 31.

Assembly InstructionsWheel Loader

7/23/2019 Wheelloader i e a4

5/7

Assembly InstructionsWheel Loader

7/23/2019 Wheelloader i e a4

6/7

7/23/2019 Wheelloader i e a4

7/7

Assembly InstructionsWheel Loader

Apply glue to the cut surface of

the paper and glue this part tothe body of the wheel loader,concealing the glue tabs.

On parts with no glue tabs,apply glue to the cutsurface of the paper.

Fold the shaft part in and glue these parts together.After attaching them to the body of the wheel loader,adjust the angle of the shaft so the headlightpoints straight forward.

Finished!Last, assemble the nameplate and

display it together with your model.