Date post: | 23-May-2018 |
Category: |
Documents |
Upload: | duongtuyen |
View: | 215 times |
Download: | 1 times |
UK and IrelandWilson Tool InternationalStirling RoadSouth Marston Ind. EstateSwindonWiltshire SN3 4XY
UKTel (Free): (0800) 373748Fax (Free): (0800) 373758IrelandTel (Free): (1-800) 709009 Fax (Free): (1-800) 535538
Office:Tel: +44 (0) 1793 831818Fax: +44 (0) 1793 831945Email: [email protected]://www.wilsontool.com
233 / 04/02 TEK
TRUMPF-STYLE Features and Benefits,TOOLING Optima™ Coating
Features and Benefits of High Precision Trumpf® Style Tooling and Wilson 241™
● Ten “standard” shapes are available at no extra charge for all tooling● All tools are ground to extremely tight tolerances● Hardened steel stripper plates to reduce marking for all tooling● Back-taper is standard on all Trumpf® and Wilson 241™ style punches● All dies are stress relieved to reduce breaking when punching thicker materials● All standard Trumpf® and Wilson 241™ style tooling are made with high speed steel,
providing you with more hits between tool sharpenings and reduced down time● “Whisper Shear” available on all punches for quieter punching with no additional lead
time required● Trumpf® Style Tooling has precision machined punch collars● Optional keyed punches and collars to eliminate punch turning and to increase
accuracy for Trumpf® Style Tooling● Direct keying standard on Wilson 241™ Style Tooling. Punches can be loaded directly
into the machine eliminating the time-consuming process of pre-setting the tool in afixture and increasing the reliability of the tooling because there is no chance of highusage punches moving in the collar while under a heavy load
The New Standard In Tooling Performance!!!
Optima™ is a proprietary TiCN (titanium carbo-nitride)coating that was custom engineered for Wilson Tool. It features unique properties that significantly enhancetooling performance. This coating, which is availableonly to Wilson Tool customers, provides a level ofsurface hardness, wear resistance and lubricity neverbefore associated with coated or uncoated punchpress tooling.
TM
UK and IrelandWilson Tool InternationalStirling RoadSouth Marston Ind. EstateSwindonWiltshire SN3 4XY
UKTel (Free): (0800) 373748Fax (Free): (0800) 373758IrelandTel (Free): (1-800) 709009 Fax (Free): (1-800) 535538
Office:Tel: +44 (0) 1793 831818Fax: +44 (0) 1793 831945Email: [email protected]://www.wilsontool.com
233 / 04/02 TEK
1
Trumpf-Style Tooling Contents
Features and Benefits
Machine Groups
241 Series Punch Holders241 Series Round241 Series Square241 Series Rectangle241 Series Standard Shapes
Standard Tools Round Size 0Standard Tools Square Size 0Standard Tools Rectangle Size 0Standard Tools Standard Shapes Size 0
Standard Tools Round Size I, II, IIIStandard Tools Square Size I, II, IIIStandard Tools Rectangle Size I, II, IIIStandard Tools Standard Shapes Size I, II, III
Multitool 4 StationMultitool 4 StationMultitool 6 StationMultitool 6 Station
Heavy Duty ToolingKeyed Collar for Rotation MachineAccessoriesTrumpf-Style AccessoriesDie and Stripper AdaptorsUrethane Stripper
Slitting PunchSlitting DieSize 0 Die AdaptorsParting Tools with Integral CollarParting Tool DiesSheet LubricationConditions of Sale
2
34567
8899
10111213
14151617
181920212223
24252627282931
Contents Page Number
2
UK and IrelandWilson Tool InternationalStirling RoadSouth Marston Ind. EstateSwindonWiltshire SN3 4XY
UKTel (Free): (0800) 373748Fax (Free): (0800) 373758IrelandTel (Free): (1-800) 709009 Fax (Free): (1-800) 535538
Office:Tel: +44 (0) 1793 831818Fax: +44 (0) 1793 831945Email: [email protected]://www.wilsontool.com
233 / 04/02 TEK
Trumpf-Style Tooling Machine Groups
CN 700CN 900CN 701CN 901
A
CN 901ECN 902CS 75CS 75.2
B
CN 1200SCN 1200aCS 15CS 20CS 20aMP 25MP 25D
C
TRUMATIC2020a202M
D
SUNIMAT 400TRUMATIC150K151K152K180K180.2K180KD180LK180.2LK
TRUMATIC202K225K235K300K300LK300PK400K
E
TRUMATIC150W152W180W180.2W180R180LW180.2LWELX/SWIFT185240240R250260R
F
TRUMATIC20aW202W300W300LW300PW300top400W
G
TRUMATIC190R200R500R600L2000R2010R2020R5000R6000L
H
MINIMATIC100TRUMATIC120R160R
S
UK and IrelandWilson Tool InternationalStirling RoadSouth Marston Ind. EstateSwindonWiltshire SN3 4XY
UKTel (Free): (0800) 373748Fax (Free): (0800) 373758IrelandTel (Free): (1-800) 709009 Fax (Free): (1-800) 535538
Office:Tel: +44 (0) 1793 831818Fax: +44 (0) 1793 831945Email: [email protected]://www.wilsontool.com
233 / 04/02 TEK
3
241 SERIES Punch Holders
Description
Punch Holder Assembly 0 - 40mmPunch Holder Assembly (0°, 45°, 90°) 0 - 40mmPunch Holder Assembly 40.01 - 76.2mmPunch Holder 0 - 40mmPunch Holder (0°, 45°, 90°) 0 - 40mmPunch Holder 40.01 - 76.2mmPunch Holder Screw M8Lockwasher for M8 ScrewScrew for Key-Holder 0 - 40mmScrew for Key-Holder 40.01 - 76.2mmKeyPrecision ground spacer 0 - 40mmPrecision ground spacer 40.01 - 76.2mm
Cat. No.
25766259382579925767259182579830161241442521524150251132580625807
Price £
0.40 Key Retaining ScrewPart No. 25215
40 - 76 Key Retaining ScrewPart No. 25150
0 - 40 Precision SpacerPart No. 25806
40 - 76 Precision SpacerPart No. 25807
8mm Locating KeyPart No. 25113
M8 Socket Head Cap ScresPart No. 30161
M8 Spring WasherPart No. 24144
0 - 40 Punch HolderPart No. 25767
0 - 40 Punch Holder (0°, 45° & 90°)Part No. 25918
40 - 70 Punch HolderPart No. 25798
4
UK and IrelandWilson Tool InternationalStirling RoadSouth Marston Ind. EstateSwindonWiltshire SN3 4XY
UKTel (Free): (0800) 373748Fax (Free): (0800) 373758IrelandTel (Free): (1-800) 709009 Fax (Free): (1-800) 535538
Office:Tel: +44 (0) 1793 831818Fax: +44 (0) 1793 831945Email: [email protected]://www.wilsontool.com
233 / 04/02 TEK
241 SERIES 1.5 mm – 76.2 mm Round
1.5 - 30.0030.01 - 40.0040.01 - 56.0056.01 - 66.0066.01 - 76.20
“d” dimensionAdd-on forOptimaTM
FLATPUNCH HSS
STANDARD
TOOLS
ROUNDWHISPER
DIE
STRIPPER
d
Cat. No. Price £
2576825774257802578625792
2576925775257812578725793
Price £
1.5 - 32.0032.01 - 77.00
“d” dimension Cat. No. Price £
2500525024
Cat. No.
KeyedGroup H
Cat. No. Price £
2500625358
UK and IrelandWilson Tool InternationalStirling RoadSouth Marston Ind. EstateSwindonWiltshire SN3 4XY
UKTel (Free): (0800) 373748Fax (Free): (0800) 373758IrelandTel (Free): (1-800) 709009 Fax (Free): (1-800) 535538
Office:Tel: +44 (0) 1793 831818Fax: +44 (0) 1793 831945Email: [email protected]://www.wilsontool.com
233 / 04/02 TEK
5
DIE
STRIPPER
1.5 - 22.0022.01 - 54.45
“a” dimension Cat. No. Price £
2548325519
KeyedGroup H
Cat. No. Price £
2551525517
STANDARD
TOOLS
SQUARE
a
241 SERIES 1.5 mm – 53.9 mm Square
FLATPUNCH HSS WHISPER
1.5 - 21.2221.23 - 28.2928.30 - 39.6039.61 - 46.6846.69 - 53.90
“a” dimensionAdd-on forOptimaTMCat. No. Price £
2581425820258262583225838
2581625822258282583425840
Price £Cat. No.
6
UK and IrelandWilson Tool InternationalStirling RoadSouth Marston Ind. EstateSwindonWiltshire SN3 4XY
UKTel (Free): (0800) 373748Fax (Free): (0800) 373758IrelandTel (Free): (1-800) 709009 Fax (Free): (1-800) 535538
Office:Tel: +44 (0) 1793 831818Fax: +44 (0) 1793 831945Email: [email protected]://www.wilsontool.com
233 / 04/02 TEK
STANDARD
TOOLS
RECTANGLE
d
241 SERIES 1.5 mm – 76.2 mm Rectangle
1.5 - 30.0030.01 - 40.0040.01 - 56.0056.01 - 66.0066.01 - 76.20
“d” dimensionAdd-on forOptimaTM
FLATPUNCH HSS WHISPER
DIE
STRIPPER
Cat. No. Price £
2581525821258272583325839
2581725823258292583525841
Price £
1.5 - 32.0032.01 - 77.00
“d” dimension Cat. No. Price £
2548425520
Cat. No.
KeyedGroup H
Cat. No. Price £
2551625518
UK and IrelandWilson Tool InternationalStirling RoadSouth Marston Ind. EstateSwindonWiltshire SN3 4XY
UKTel (Free): (0800) 373748Fax (Free): (0800) 373758IrelandTel (Free): (1-800) 709009 Fax (Free): (1-800) 535538
Office:Tel: +44 (0) 1793 831818Fax: +44 (0) 1793 831945Email: [email protected]://www.wilsontool.com
233 / 04/02 TEK
7
Standard Shapes
241 SERIES 1.5 mm – 76.2 mm Standard Shapes
FLATPUNCH HSS WHISPER
1.5 - 30.0030.01 - 40.0040.01 - 56.0056.01 - 66.0066.01 - 76.20
“d” dimensionAdd-on forOptimaTM
DIE
STRIPPER
Cat. No. Price £
2577125777257832578925795
2577225778257842579025796
Price £
1.5 - 32.0032.01 - 77.00
“d” dimension Cat. No. Price £
2502725000
Cat. No.
KeyedGroup H
Cat. No. Price £
2502825359
d
d
d
d
d
d
d
d
OBROUND
HEXAGON
OCTAGON
SINGLE “D”
DOUBLE “D”
LONG “D”
QUADRA “D”
EQUILATERALTRIANGLE
8
UK and IrelandWilson Tool InternationalStirling RoadSouth Marston Ind. EstateSwindonWiltshire SN3 4XY
UKTel (Free): (0800) 373748Fax (Free): (0800) 373758IrelandTel (Free): (1-800) 709009 Fax (Free): (1-800) 535538
Office:Tel: +44 (0) 1793 831818Fax: +44 (0) 1793 831945Email: [email protected]://www.wilsontool.com
233 / 04/02 TEK
TRUMPF-STYLE Round and SquareSTANDARD TOOLS Size 0
– 39.00*
– 78.50 Keyed
Non Keyed
Group H
Punch Size 0
HSS
* For machines Group S.
Size ‘‘d’’ dimension
1.50 – 6.00
6.01 – 10.50
Add on for OptimaTM
Cat. No. Price £
25008
25009
Cat. No. Price £
Cat. No. Price £
25032
25006
25136
25358
Cat. No. Price £
25541
25515
25137
25517
Cat. No. Price £
25475
2547700
Stripper size I/II
Size
I
II
‘‘d’’ dimension
– 32.00
Die, Size I
Size
I
‘‘d’’ dimension
25005
Cat. No. Price £
25483
– 26.40**
– 55.00 Keyed
Non Keyed
Group H
Punch Size 0
HSS
Size ‘‘a’’ dimension
1.50 – 4.20
4.21 – 7.40
Add on for OptimaTM
Stripper size I/II
Size
I
II
‘‘a’’ dimension
– 22.00
Die, Size I
Size
I
‘‘a’’ dimension
d a
Size Cat. No. Price £
0–6.006.01–10.5
2501025021
UK and IrelandWilson Tool InternationalStirling RoadSouth Marston Ind. EstateSwindonWiltshire SN3 4XY
UKTel (Free): (0800) 373748Fax (Free): (0800) 373758IrelandTel (Free): (1-800) 709009 Fax (Free): (1-800) 535538
Office:Tel: +44 (0) 1793 831818Fax: +44 (0) 1793 831945Email: [email protected]://www.wilsontool.com
233 / 04/02 TEK
9
TRUMPF-STYLE Rectangle andSTANDARD TOOLS Standard Shape Size 0
– 39.00**
– 78.50 Keyed
Non Keyed
Group H
Punch Size 0
HSS
* For machines Group S.
0
1.80 – 6.00
6.01 – 10.50
Add on for OptimaTM
Stripper size I/II
I
II
– 32.00
Die, Size I
I
Punch Size 0
HSS
OBROUNDAND ALL OTHERSTANDARD SHAPES
0
2.00 – 6.00
6.01 – 10.50
Add on for OptimaTM
Stripper size I/II
– 32.00
Die, Size I
I
d
d
Cat. No. Price £Size ‘‘d’’ dimension
25484 25027
Cat. No. Price £
25030
25028
25137
25359
– 39.00**
– 78.50 Keyed
Non Keyed
Group H
Size
I
II
‘‘d’’ dimension
Cat. No. Price £Size ‘‘d’’ dimension
Cat. No. Price £
25476
25478
Size ‘‘d’’ dimension Cat. No. Price £
25022
25023
Size ‘‘d’’ dimension
Cat. No. Price £
25542
25516
25137
25518
Size ‘‘d’’ dimension
STANDARD SHAPES
Size Cat. No. Price £
0–6.006.01–10.5
2501025021
10
UK and IrelandWilson Tool InternationalStirling RoadSouth Marston Ind. EstateSwindonWiltshire SN3 4XY
UKTel (Free): (0800) 373748Fax (Free): (0800) 373758IrelandTel (Free): (1-800) 709009 Fax (Free): (1-800) 535538
Office:Tel: +44 (0) 1793 831818Fax: +44 (0) 1793 831945Email: [email protected]://www.wilsontool.com
233 / 04/02 TEK
TRUMPF-STYLE STANDARD TOOLS Round Size I, II, III
I 1.5 - 10.5I 10.51 - 30.00II 30.01 - 38.00 *II 30.01 - 40.00II 40.01 - 50.80II 50.81 - 60.00II 60.01 - 72.00II 72.01 - 76.20III 76.21 - 105.00
Size “d” dimension Add-on for OptimaTM
FLATPUNCH HSS
STANDARD
TOOLS
ROUNDWHISPER
I - 32.00I - 38.80 *II 32.01 - 72.00III - 107.00
Size “d” dimension
DIE
I - 41.00*II - 78.00 Keyed
Non-KeyedGroup H
III - 106.00 KeyedNon-Keyed
STRIPPER
* For machines Group S.
d
Cat. No. Price £
250042500425035250422504325002250022500225003
–2506925071250712507225073250732507325074
25005250552502425060
Cat. No. Price £
Cat. No. Price £
Size “d” dimension
250322500625136253582506125318
Cat. No. Price £
UK and IrelandWilson Tool InternationalStirling RoadSouth Marston Ind. EstateSwindonWiltshire SN3 4XY
UKTel (Free): (0800) 373748Fax (Free): (0800) 373758IrelandTel (Free): (1-800) 709009 Fax (Free): (1-800) 535538
Office:Tel: +44 (0) 1793 831818Fax: +44 (0) 1793 831945Email: [email protected]://www.wilsontool.com
233 / 04/02 TEK
11
TRUMPF-STYLE STANDARD TOOLS Square Size I, II, III
I 1.50 - 10.50I 10.51 - 21.50II 21.51 - 26.80*II 21.51 - 28.56II 28.57 - 35.92II 35.93 - 42.70II 42.71 - 54.00III 54.01 - 74.52
FLATPUNCH HSS
STANDARD
TOOLS
SQUAREWHISPER
DIE
STRIPPER
* For machines Group S.
NOTE: The above “a” dimensions are for conventional steel stripping and Pullmax only.For push-on Urethane stripping applications, refer to Contents page of the catalogue.
a
Size “a” dimension Add-on for OptimaTMCat. No. Price £
2548725487255372549125501255112551125521
–25489254932549325503255132551325523
Cat. No. Price £
255412551525137255172552525320
I - 23.00I - 26.20*II 23.01 - 55.40III - 73.00
Size “a” dimension
25483254852551925527
Cat. No. Price £
I - 26.40*II - 55.00 Keyed
Non-KeyedGroup H
III - 76.00 KeyedNon-Keyed
Size “a” dimension Cat. No. Price £
12
UK and IrelandWilson Tool InternationalStirling RoadSouth Marston Ind. EstateSwindonWiltshire SN3 4XY
UKTel (Free): (0800) 373748Fax (Free): (0800) 373758IrelandTel (Free): (1-800) 709009 Fax (Free): (1-800) 535538
Office:Tel: +44 (0) 1793 831818Fax: +44 (0) 1793 831945Email: [email protected]://www.wilsontool.com
233 / 04/02 TEK
TRUMPF-STYLESTANDARD TOOLS Rectangle Size I, II, III
FLATPUNCH HSS
STANDARD
TOOLS
RECTANGLEWHISPER
DIE
STRIPPER
I 1.50 - 12.00I 12.01 - 30.42II 30.01 - 38.00*II 30.43 - 40.40II 40.41 - 50.80II 50.81 - 60.40II 60.41 - 76.40III 76.41 - 105.40
d
Size “d” dimension Add-on for OptimaTM
I - 32.00I - 38.80*II 32.01- 76.40III - 107.00
Size “d” dimension
I - 39.40*II - 78.00 Keyed
Non-KeyedGroup H
III - 107.00 KeyedNon-Keyed
Cat. No. Price £
2548825488255382549225502255122551225552
–25490254942549425504255142551425524
25484254862552025528
Cat. No. Price £
Cat. No. Price £
Size “d” dimension
255422551625137255182552625320
Cat. No. Price £
* For machines Group S.
NOTE: The above “d” dimensions are for conventional steel stripping and Pullmax only.For push-on Urethane stripping applications, refer to Contents page of the catalogue.
UK and IrelandWilson Tool InternationalStirling RoadSouth Marston Ind. EstateSwindonWiltshire SN3 4XY
UKTel (Free): (0800) 373748Fax (Free): (0800) 373758IrelandTel (Free): (1-800) 709009 Fax (Free): (1-800) 535538
Office:Tel: +44 (0) 1793 831818Fax: +44 (0) 1793 831945Email: [email protected]://www.wilsontool.com
233 / 04/02 TEK
13
TRUMPF-STYLE Standard ShapesSTANDARD TOOLS Size I, II, III
I 1.50 - 12.00I 12.01 - 30.42II 30.01 - 38.00*II 30.43 - 40.40II 40.41 - 50.80II 50.81 - 60.40II 60.41 - 76.40III 76.41 - 105.40
FLATPUNCH HSS WHISPER
I - 32.00I - 38.80 *II 32.01 - 76.40III - 107.00
DIE
STRIPPER
d
d
d
d
d
d
d
d
OBROUND
Standard Shapes
HEXAGON
OCTAGON
SINGLE “D”
DOUBLE “D”
LONG “D”
QUADRA “D”
EQUILATERALTRIANGLE
Size “d” dimension Add-on for OptimaTMCat. No. Price £
2502625026250312503925040250012500125025
–25063250652506525066250672506725068
Cat. No. Price £
Size “d” dimension
25027250442500025059
Cat. No. Price £
I - 39.00*II - 78.00 Keyed
Non-KeyedGroup H
III - 107.00 KeyedNon-Keyed
Size “d” dimension
250302502825137253592506225320
Cat. No. Price £
* For machines Group S.
NOTE: The above “d” dimensions are for conventional steel stripping and Pullmax only.For push-on Urethane stripping applications, refer to Contents page of the catalogue.
14
UK and IrelandWilson Tool InternationalStirling RoadSouth Marston Ind. EstateSwindonWiltshire SN3 4XY
UKTel (Free): (0800) 373748Fax (Free): (0800) 373758IrelandTel (Free): (1-800) 709009 Fax (Free): (1-800) 535538
Office:Tel: +44 (0) 1793 831818Fax: +44 (0) 1793 831945Email: [email protected]://www.wilsontool.com
233 / 04/02 TEK
TRUMPF-STYLE Multitool 4 Station
Cat. No. Price £
25888
Trumatic 240R/260R
Multitool Tool complete,4 Station
Cat. No. Price £
25886
Trumatic 200/500/600
Multitool Tool complete,4 Station
Cat. No. Price £
25891Punch Adaptor complete,
4 Station
Cat. No. Price £
25884
Cat. No. Price £
25866Die Adaptor complete,
4 Station
Cat. No. Price £
25866Die Adaptor complete,
4 Station
Punch Adaptor complete, 4 Station
UK and IrelandWilson Tool InternationalStirling RoadSouth Marston Ind. EstateSwindonWiltshire SN3 4XY
UKTel (Free): (0800) 373748Fax (Free): (0800) 373758IrelandTel (Free): (1-800) 709009 Fax (Free): (1-800) 535538
Office:Tel: +44 (0) 1793 831818Fax: +44 (0) 1793 831945Email: [email protected]://www.wilsontool.com
233 / 04/02 TEK
15
TRUMPF-STYLE Multitool 4 Station
PUNCH HSS
OptimaTM
DIE
25153
MULTI-TOOL
Maximum Punch size: 16mm
4-Station
270°
0°
90°
180°
270°
0°
90°
180°
270°
0°
90°
180°
270°
0°
90°
180°
1 (45°) 4 (315°)
3 (225°)2 (135°)
N.B.Please give position andangle when ordering
Example:Position 1Angle 90°
a
d
d
Cat. No. Price £
25151
Cat. No. Price £
OptimaTM
25531
Cat. No. Price £
25529
Cat. No. Price £
OptimaTM
25532
Cat. No. Price £
25530
Cat. No. Price £
OptimaTM
25154
Cat. No. Price £
25152
Cat. No. Price £
Round punches Optima™ coated as standard.
Standard Shapes
OBROUND HEXAGON OCTAGON SINGLE “D” DOUBLE “D” LONG “D” QUADRA “D”
d
dd
d d dd d
TRIANGLE
60°
16
UK and IrelandWilson Tool InternationalStirling RoadSouth Marston Ind. EstateSwindonWiltshire SN3 4XY
UKTel (Free): (0800) 373748Fax (Free): (0800) 373758IrelandTel (Free): (1-800) 709009 Fax (Free): (1-800) 535538
Office:Tel: +44 (0) 1793 831818Fax: +44 (0) 1793 831945Email: [email protected]://www.wilsontool.com
233 / 04/02 TEK
TRUMPF-STYLE Multitool 6 Station
Cat. No. Price £
25889
Trumatic 240R/260R
Multitool complete,6 Station
Cat. No. Price £
25887
Trumatic 200/500/600
Multitool complete,6 Station
Cat. No. Price £
25892Punch Adaptor complete,
6 Station
Cat. No. Price £
25885Punch Adaptor complete,
6 Station
Cat. No. Price £
25863Die Adaptor complete,
6 Station
Cat. No. Price £
25863Die Adaptor complete,
6 Station
UK and IrelandWilson Tool InternationalStirling RoadSouth Marston Ind. EstateSwindonWiltshire SN3 4XY
UKTel (Free): (0800) 373748Fax (Free): (0800) 373758IrelandTel (Free): (1-800) 709009 Fax (Free): (1-800) 535538
Office:Tel: +44 (0) 1793 831818Fax: +44 (0) 1793 831945Email: [email protected]://www.wilsontool.com
233 / 04/02 TEK
17
Standard Shapes
OBROUND HEXAGON OCTAGON SINGLE “D” DOUBLE “D” LONG “D” QUADRA “D”
d
dd
d d dd d
TRIANGLE
60°
TRUMPF-STYLE Multitool 6 Station
Maximum Punch size: 10.5mm
270°
0°
90°
180°
270°
0°
90°
180°
270°
0°
90°
180°
270°
0°
90°
180°
1 (30°) 6 (330°)
4 (210°)3 (150°)
270°
0°
90°
180°
270°
0°
90°
180°
2(90°) 5(270°)
MULTI-TOOL
a
d
d
PUNCH HSS
OptimaTM
DIE
25149
N.B.Please give position andangle when ordering
Example:Position 1Angle 90°
Cat. No. Price £
25147
Cat. No. Price £
OptimaTM
25535
Cat. No. Price £
25533
Cat. No. Price £
OptimaTM
25536
Cat. No. Price £
25534
Cat. No. Price £
OptimaTM
25150
Cat. No. Price £
25148
Cat. No. Price £
Round punches Optima™ coated as standard.
STANDARDSHAPES
6-Station
18
UK and IrelandWilson Tool InternationalStirling RoadSouth Marston Ind. EstateSwindonWiltshire SN3 4XY
UKTel (Free): (0800) 373748Fax (Free): (0800) 373758IrelandTel (Free): (1-800) 709009 Fax (Free): (1-800) 535538
Office:Tel: +44 (0) 1793 831818Fax: +44 (0) 1793 831945Email: [email protected]://www.wilsontool.com
233 / 04/02 TEK
TRUMPF-STYLE Heavy Duty Tooling
The Heavy Duty system is designed to withstand the highertonnage associated with punching and nibbling thickermaterials. The punch is strengthened by having a largeshoulder, enabling it to withstand the higher forces involved. Italso has extra back taper as standard, reducing the gallingand pick-up often associated with thicker materials. Optima™coating will also greatly reduce this. The die is strengthened bya boss on the bottom making the effective thickness of the dielarger.
1. Heavy Duty flat punch (0-40mm)1. Heavy Duty whisper punch (0-40mm)1. Heavy Duty punch (Rooftop)
(40-76mm)
2. Heavy Duty Die3. Stripper, Keyed4. Stripper, Non-keyed5. Stripper Group H6. Heavy Duty system collar7. Spare collar key8. Key locating screw
Collar clamping screw (not shown)Die shim pack (not shown)
2514025322
25407
251802500625136253582513825142252152521625182
2514125321
25406
251622502825137253592513825142252152521625182
2514125321
25406
251622551525137255172513825142252152521625182
2514125321
25406
251622551525137255172513825142252152521625182
Description Cat. No. Price £ Cat. No. Price £ Cat. No. Price £ Cat. No. Price £
Round Shape Square Rectangle
➀
➆
➇
➂
➄
➃
➁
➅ ● Size and shape required● Material thickness and type● Machine model● Is shear required?
Information needed:
● Minimum Punch dia 10.00mm (Below this use standard size 1 punch)
● Maximum die ‘‘A’’ dimension 55mm (Except56 x 5mm slitting tool)
● Uses Heavy Duty system collar● Has extra back taper as standard● 1.00mm rads on corners will increase the life
of the punch and die● Rooftop shear will reduce the tonnage
significantly as long as the depth of shear isat least half the thickness of the material
● Heavy Duty punch to be used on material6.0mm thick and above or where punchingforce is over 200KN
● Heavy Duty die to be used where punchingforce is over 180KN
● Uses standard strippers● Tools for thicker plate often exceed the
machine tonnage. Ask the sales desk tocheck this for you
● The Punches are flat as standard, if yourequire concave or any other shear, pleasestate on order
Design criteria:
OptimaTM add-on for punches: 0-30mm £ , 30-76mm £
UK and IrelandWilson Tool InternationalStirling RoadSouth Marston Ind. EstateSwindonWiltshire SN3 4XY
UKTel (Free): (0800) 373748Fax (Free): (0800) 373758IrelandTel (Free): (1-800) 709009 Fax (Free): (1-800) 535538
Office:Tel: +44 (0) 1793 831818Fax: +44 (0) 1793 831945Email: [email protected]://www.wilsontool.com
233 / 04/02 TEK
19
TRUMPF-STYLE Keyed Collar for Rotation Machine
The Wilson Tool Keyed Collar
● Fixed slots for greater accuracy andconsistency.
● Reduced downtime.No need to use Quick Set.
● Much faster than Quick Set allowing theoperator to carry out further tasks.
● Inherent accuracy reduces the reliance requiredon the operator.
● Consequent scrap rate reduction. The punch cannot turn at all during operation.
With the increase in the number of rotationmachines being used, the need for faster methodsof accurate set up is becoming ever greater. Tomeet this demand, Wilson Tool have designed thekeyed collar, giving greater accuracy and durabilitywhile reducing downtime.
The rotation feature of the machine enables the toolto remain in the holder for longer periods of timewithout being checked. For operators to takeadvantage of this opportunity and to eliminate therisk of punch movement and consequent scrap,Wilson Tool have developed a positive locationbetween the punch and collar. The movement risk isnow gone and the positioning is 100% reliable andrepeatable.
This system is more accurate than using Quick Setwith any of its inherent operational margins for error.
This time-saver works by simply placing the collaron the punch and tightening one screw. Thisprovides 100% accurate alignment every time!
Component Parts
Pictorial representation showing collar fitted to punch
1. Punch.2. Keyed collar.3. Grub screw.4. Ball bearing.5. Dowel pin.6. Spring loaded ball bearing (factory set).
Rotation machinesThe Wilson Tool Keyed Collar has been specificallydesigned for Trumpf rotation machines. It enables thetool to be set at either 0° or 90° without the use of QuickSet.This keyed collar is designed for use with Wilson ToolTRUMPF-STYLE punches which have dowel pinsattached.
Non-rotation machinesA second version of the keyed collar is also available fornon-rotation machines. This one has an additional twoslots set at 45° and 135°.
Price£
Description
Keyed Punch
60.5 mm Max. Flat60.5 – 76.2 mm Flat60.5 mm Max. Whisper60.5 – 76.2 mm WhisperSize III FlatSize III Whisper
Optima™
Price £Cat.No.
Keyed Collar
253762557525576255772557825579
2557325317
0° & 90°0°, 45°, 90° & 135°
1
5 2
6
3
4
20
UK and IrelandWilson Tool InternationalStirling RoadSouth Marston Ind. EstateSwindonWiltshire SN3 4XY
UKTel (Free): (0800) 373748Fax (Free): (0800) 373758IrelandTel (Free): (1-800) 709009 Fax (Free): (1-800) 535538
Office:Tel: +44 (0) 1793 831818Fax: +44 (0) 1793 831945Email: [email protected]://www.wilsontool.com
233 / 04/02 TEK
TRUMPF-STYLE Accessories
Shear Grinding Fixture
• Easy to adjust angle setting for shear grinding.• Can be used with your existing surface grinder.• Easy to use instruction sheet with grinding tips.
Features and Benefits
• Simplified, economical design.• Robust yet portable fixture.• Precision-made body with very few wearable
parts.• Angle settings of 0°, 45°, 90°.• Easy to use – regrind length charts included.• Extremely accurate.• Ergonomically designed.
• Versatile. The fixture can take all types of Trumpf-style collars: Size I, Size II, Minimatic-style, HeavyDuty, Manual, plus forming tools that do not haveintegral collars. Can be used for flat and whisper-style punches.
• Variety. Suitable for Trumpf, Pullmax, Omes,Euromac, Kunz and Boschert machines.
Grinding Fixture and Components
Alignment Fixture
Price £Description
Grinding Fixture(includes 1 copy of instructions)
Punch HolderDie, size IDie, size IIMulti-tool Punch (MT-6)Multi-tool Die (MT-6)Multi-tool Punch (MT-4)Multi-tool Die (MT-4)Pullmax-style Orbit PunchPullmax-style Orbit Die
Cat. No.
06034
060892536525366253032530525302253046208762088
Price £Description
Alignment Fixture
Cat. No.
24186
UK and IrelandWilson Tool InternationalStirling RoadSouth Marston Ind. EstateSwindonWiltshire SN3 4XY
UKTel (Free): (0800) 373748Fax (Free): (0800) 373758IrelandTel (Free): (1-800) 709009 Fax (Free): (1-800) 535538
Office:Tel: +44 (0) 1793 831818Fax: +44 (0) 1793 831945Email: [email protected]://www.wilsontool.com
233 / 04/02 TEK
21
TRUMPF-STYLE Accessories
Alignment collars for auto-tool changeMachine groups E/F/G/H
Alignment collars for manual tool changemachine groups A/B/C/D
Size
I
Cat. No.
25018
Price £ Size Cat. No. Price £
Size Cat. No. Price £ Size Cat. No. Price £
Price £
II/III 25139
I 25197 II/III 25198
Alignment collar for heavy duty punch
Size Cat. No. Price £
I/II 25138
Alignment collars for machine group S
Size Cat. No. Price £ Size Cat. No.
I 25186 II 25188
22
UK and IrelandWilson Tool InternationalStirling RoadSouth Marston Ind. EstateSwindonWiltshire SN3 4XY
UKTel (Free): (0800) 373748Fax (Free): (0800) 373758IrelandTel (Free): (1-800) 709009 Fax (Free): (1-800) 535538
Office:Tel: +44 (0) 1793 831818Fax: +44 (0) 1793 831945Email: [email protected]://www.wilsontool.com
233 / 04/02 TEK
TRUMPF-STYLE Die and Stripper Adaptors
Die Adaptor,machine groups F/H
Size
I/IIShim pack
Cat. No.
2516525181
Price £
Size Cat. No. Price £
Size Cat. No. Price £
Size Cat. No. Price £
I/III 25168Shim pack 25181
II/III 25167Shim pack 25182
II/III 25155
Die Adaptor,machine group G
Die Adaptor,machine group G
Stripper Adaptor,machine group G
UK and IrelandWilson Tool InternationalStirling RoadSouth Marston Ind. EstateSwindonWiltshire SN3 4XY
UKTel (Free): (0800) 373748Fax (Free): (0800) 373758IrelandTel (Free): (1-800) 709009 Fax (Free): (1-800) 535538
Office:Tel: +44 (0) 1793 831818Fax: +44 (0) 1793 831945Email: [email protected]://www.wilsontool.com
233 / 04/02 TEK
23
Price £
TRUMPF-STYLE Urethane Stripper
The Wilson Tool designed urethanestripper is suitable for any manualmachine using Trumpf tooling. Itreduces set up times, provides closerstripping and reduces punchingnoise. It also reduces the problem ofsheet marking associated with metalstrippers in thin or soft material.
25333
25334
25335
25336
25337
Consult Sales Desk ConsultSales Desk
ConsultSales Desk
ConsultSales Desk
ConsultSales Desk
Up to 30mm
30.01 to 40mm
40.01 to 50mm
50.01 to 60mm
60.01 to 65mm
65.01 to 105mm
25004
25042
25043
25002
25002
25487
25491
25501
25511
25511
25488
25492
25502
25512
25512
25036
35039
25040
25001
25001
Information needed:
Design criteria:
Price List
Range Cat. No. Round Square ObroundRectangle
● Punch size and range
● Designed for use in thin sheets only.2mm mild steel and aluminium, 1.6mmstainless steel maximum sheet thickness
● Round and shaped sizes up to the 65mmrange are supplied blank for punching theaperture whilst in the press. Round andshaped sizes in the 65mm range haveapertures pre-milled by Wilson Tool
● Instructions included with each order● Punch, collar and key are not included in the
price. Shown for reference only
24
UK and IrelandWilson Tool InternationalStirling RoadSouth Marston Ind. EstateSwindonWiltshire SN3 4XY
UKTel (Free): (0800) 373748Fax (Free): (0800) 373758IrelandTel (Free): (1-800) 709009 Fax (Free): (1-800) 535538
Office:Tel: +44 (0) 1793 831818Fax: +44 (0) 1793 831945Email: [email protected]://www.wilsontool.com
233 / 04/02 TEK
TRUMPF-STYLE Slitting Punch
2520225142252152526225311252042513825205252072520325310
25112
2520825580
N/A25006
This tool provides a more cost effective method of slitting,along with the advantages of closer stripping.The Wilson Tool design, on the 56 x 5mm avoids the halfmoon stripper locking up as on the old design. Wilson Toolsupplies parts for the old design as well as our newdesign. The collar is the same as used on the heavy dutytooling.
● Conventional obround punch or specialsize
● Size required● Material thickness and type● Machine model● Wilson Tool design or old style
Information needed:
● Maximum material thickness 2.5mm● Used with standard stripper around
outside● Blade supplied only with rooftop shear● Must be reground in vibration-free fixture,
with coolant● For special sizes or shape consult sales
desk● For regrinding or blade replacement, lift
stripper off first, then remove urethane
Design criteria:
Full assembly Wilson Tool Design 56 x 5mm OB Inc. Collar
25201
25313
25206
Full assembly Old Design56 x 5mm OB Inc. Collar
Full assembly,76.2 x 5mm OB Inc. Collar
1. Holder2. Collar key only3. Key fixing screw4. Blade fixing screw5. Blade locating pin6. Urethane spring (pair)7. Collar Inc. key (Heavy Duty)8. Urethane fixing screw9. Half moon strippers (pair)9. Full stripper for (56 x 5mm OB)
10. Punch blade (56 x 5mm OB) WT
10. Punch blade (56 x 5mm OB) Old style
10. Punch blade (76.2 x 5mm OB)10. Punch blade special size
Optima™Standard stripper
Improved stripping on theWilson Tool design of 56 x 5mm slitting tool
Stripping on old design(56 x 5mm)
Stripping on Wilson Tooldesign (56 x 5mm)
Description DescriptionCat. No. Price £ Cat. No. Price £
UK and IrelandWilson Tool InternationalStirling RoadSouth Marston Ind. EstateSwindonWiltshire SN3 4XY
UKTel (Free): (0800) 373748Fax (Free): (0800) 373758IrelandTel (Free): (1-800) 709009 Fax (Free): (1-800) 535538
Office:Tel: +44 (0) 1793 831818Fax: +44 (0) 1793 831945Email: [email protected]://www.wilsontool.com
233 / 04/02 TEK
25
TRUMPF-STYLE Slitting Die
● Conventional rectangle with rads orspecial size
● Size required● Material thickness and type or die
clearance● Machine model
Information needed:
● Maximum material thickness 2.5mm● The die blades can be reground by
0.25mm maximum● Do not grind the top of the die base● To ensure the screws do not come loose,
re-assemble using Loctite®
● Must be held flat for regrinding andcoolant must be used
● For special size or shape consult salesdesk
Design criteria:
This tool not only provides a more cost effective methodof slitting, but it gives a better quality finish on the edgeof the sheet. This is achieved by using rectangle withrads for the die blades combined with an obroundpunch. This die assembly combines HSS inserts with adie body manufactured from a shock resistant steel,giving the best combination for long life.
Die blades to suit indexing die holder are alsoavailable for use on non rotation machines
(Blades only available)
This combination of obround punch and a dierectangle with rads gives the best sheet edge finish
Rectangle with rads die Obround punch
1. Die base2. Die blade (pair) 56 x 5mm2. Die blade (pair) 76.2 x 5mm2. Die blade (pair) special size3. Shim4. Location dowel5. Blade fixing screw
6. Indexing die blade (pair) 56 x 5mm
25013250122536325569251852536225224
25131
Description Cat. No. Price £
1
4 5 23
1
6
26
UK and IrelandWilson Tool InternationalStirling RoadSouth Marston Ind. EstateSwindonWiltshire SN3 4XY
UKTel (Free): (0800) 373748Fax (Free): (0800) 373758IrelandTel (Free): (1-800) 709009 Fax (Free): (1-800) 535538
Office:Tel: +44 (0) 1793 831818Fax: +44 (0) 1793 831945Email: [email protected]://www.wilsontool.com
233 / 04/02 TEK
TRUMPF-STYLE Size 0 Die Adaptors
The Wilson Tool designed adaptors are a lowcost die option for size 0 tooling. When used inconjunction with a punch chuck, only new punchand die inserts need to be purchased for eachnew size and shape.
1. Full Die Adaptor assembly, including shimpack but not including Size 0 die. 25380 25381
2. 6.5mm DIA steel ball. (Not Shown)
3. M8 x 10 long Socket Set Screw. (Not Shown)
4. Shim Pack (2 x 0.1mm, 1 x 0.3, 1 x 0.5)
5. Size 0 Die (Round)
6. Size 0 Die (Shape)
25387
25391
25388
25149
25150
25387
25391
25388
25149
25150
Component Parts
DescriptionGroup S Machines All other Machines
Cat. No. Cat. No.Price £ Price £
● Size, shape and angular position required fordie orders
● Material type and thickness required for die orders
● Machine model
Information needed:
● Size 0 dies are manufactured from M2 HighSpeed Steel as standard
● Die adaptors are manufactured from highquality tool steel for long life
● Die adaptors are high precision for accuratetool loading
● Size 0 dies are compatible with 6 stationMultitool
Design criteria:
UK and IrelandWilson Tool InternationalStirling RoadSouth Marston Ind. EstateSwindonWiltshire SN3 4XY
UKTel (Free): (0800) 373748Fax (Free): (0800) 373758IrelandTel (Free): (1-800) 709009 Fax (Free): (1-800) 535538
Office:Tel: +44 (0) 1793 831818Fax: +44 (0) 1793 831945Email: [email protected]://www.wilsontool.com
233 / 04/02 TEK
27
TRUMPF-STYLE Parting Tools with Integral Collar
● Maximum material thickness is 3.0mm● Used with standard stripper● Blades supplied only with rooftop shear● Must be reground in vibration-free fixture, with
coolant● Special sizes and shapes available.
Must fit within ranges as specified
Design criteria:Complete Assy without Blade 0° 25600
Complete Assy without Blade 90° 25602
Location Pin 25444
Blade Locking Screw 25345
56 x 5mm RT Blade 25346
30 x 5mm RT Blade 25347
76.2 x 5mm RT Blade 25414
0-30 x 5mm Blade (Special) 25447
30-56 x 5mm Blade (Special) 25448
56-76.2 x 5mm Blade (Special) 25449
Optima™ coating –
Component Parts
Description Cat. No. Price £
The parting tool punch holder is designed toaccept all three interchangeable punch blades(30 x 5mm, 56 x 5mm & 76.2 x 5mm), andspecial shapes which fit within a 76.2 x 5mm RT.
The blades have a regrind life of 3mm and theassembly is limited to use in up to 3mm material.The blades are supplied with rooftop shear asstandard, to reduce punching force and noise.The Parting Punch Assembly is permanently setat either 0° or 90° eliminating any risk ofmisalignment of the blade.
For Special Shape Blade prices please consult salesdesk.
Parting Punch Assembly
● Conventional rectangle size or special size andshape
● Material type and thickness● Machine model● Optima™ coating option
Information needed:
The Wilson Tool Parting ToolsThe parting tool punches and dies can be used to provide a more cost effective method of slitting. Insteadof replacing the entire punch and die, only new blades need to be re-ordered. There are two fixed collaroptions available, one at 0° and one at 90°. The fixed collar enables quicker set up times and greateraccuracy.
The blades are available in the following common slitting tool sizes:- 30.0mm x 5.0mm RT56.0mm x 5.0mm RT76.2mm x 5.0mm RT
However, special shapes and sizes can be produced to suit your application (e.g. special inverted diamondblades for microjointing).
28
UK and IrelandWilson Tool InternationalStirling RoadSouth Marston Ind. EstateSwindonWiltshire SN3 4XY
UKTel (Free): (0800) 373748Fax (Free): (0800) 373758IrelandTel (Free): (1-800) 709009 Fax (Free): (1-800) 535538
Office:Tel: +44 (0) 1793 831818Fax: +44 (0) 1793 831945Email: [email protected]://www.wilsontool.com
233 / 04/02 TEK
TRUMPF-STYLE Parting Tool Dies
30 x 5mm & 56 x 5mm Parting Tool Die Assembly
76.2 x 5mm Parting Tool Die Assembly
The blade holder is designed to accept theinterchangeable 30 x 5mm and 56 x 5mmdie blades, and also any special shapeswhich fit within a 56 x 5mm RT.
The blade holder is designed to accept the76.2 x 5mm die blades, and also anyspecial shapes which fit within a 76.2 x5mm RT.
● Conventional rectangle size or special size andshape
● Material type and thickness● Machine model
Information needed:
● Special sizes and shapes available. Must fit withinranges as specified
● Maximum material thickness is 3.0mm● Blades can be reground by 1.0mm max● Must be held flat for regrinding and coolant must be
used● To ensure the screws do not come loose,
reassemble using Loctite
Design criteria:
1. Complete Assy without Blade2. Blade Fixing Screw3. 76.2 x 5mm RT Blade4. 56-76.2 x 5mm Blade (Special)5. Shim Pack (not shown)
2546625443254292546525441
Description Cat. No. Price £
1. Complete Assy without Blade2. Blade Fixing Screw3. 30 x 5mm RT Blade4. 56 x 5mm RT Blade5. 0-56 x 5mm Blade (Special)6. Shim Pack (not shown)
254642544325417254622546325439
Description Cat. No. Price £
For Special Shape Blade prices pleaseconsult sales desk.
For Special Shape Blade prices pleaseconsult sales desk.
3
4
5
1
2
3
4
1
2
UK and IrelandWilson Tool InternationalStirling RoadSouth Marston Ind. EstateSwindonWiltshire SN3 4XY
UKTel (Free): (0800) 373748Fax (Free): (0800) 373758IrelandTel (Free): (1-800) 709009 Fax (Free): (1-800) 535538
Office:Tel: +44 (0) 1793 831818Fax: +44 (0) 1793 831945Email: [email protected]://www.wilsontool.com
233 / 04/02 TEK
29
SHEET LUBRICATION PennNib C Blue and PennNib Si
● Easy stripping● Longer tool life● High film strength for metal forming● Easier degreasing prior to painting● Can be used on carbon steel, copper, brass
and aluminium● No stickiness due to tacky oils.
The advantages of using PennNib Sare as follows:
● Use of highly inflammable andhazardous solvents is not required
● No irritating smoke during subsequent welding operations
● No oil mist● No eczema or allergy problems
Fire risks and health hazardsare reduced:
● Store at temperatures above 0°C● Shake bottle well before use
Handling and storage:
1. PennNib S 1 litre ready to use spray2. PennNib C Blue 5 litre concentrate
2400024005
Description Cat. No. Price £
For further information, pleasecontact the Sales Desk
PennNib S and PennNib C Blue are waterbased fluids developed specifically forpunching, nibbling and shearing operations. Italso helps in forming operations, as alubricated sheet marks much less than a non-lubricated sheet.
PennNib S is available in ready-mixedhandy 1 litre, ready to use, spraybottles.
PennNib C Blue is supplied as aconcentrate in 5 litre bottles, and isdilutable with water. The normal dilutionratio is 1:10 with water for mostoperations, and applied by brush orsprayed onto the material.
30
UK and IrelandWilson Tool InternationalStirling RoadSouth Marston Ind. EstateSwindonWiltshire SN3 4XY
UKTel (Free): (0800) 373748Fax (Free): (0800) 373758IrelandTel (Free): (1-800) 709009 Fax (Free): (1-800) 535538
Office:Tel: +44 (0) 1793 831818Fax: +44 (0) 1793 831945Email: [email protected]://www.wilsontool.com
233 / 04/02 TEK
PennNib S Information on risk and safety precautionsI
Date of issue Trade name
19880126 PENNNIB C (BLUE)Type of product/use Buyer’s denomination of product
Nibbling, punching andshearing fluid Checked at the buyer’s by Sign. Date
Labelling Main text Danger symbol
1) Irritating to eyes XiHealth hazard (inhalation, ingestion, contact with skin or eyes)
Inhalation – N.A.
Skin contact – moderately irritating, degreasing. May cause allergic reactions due toGrotan BK.
Eye contact – painful, strongly irritating, may cause minor burns.
Ingestion – very low acute toxicity. May cause slight irritation of mucous membranes.
Fire andexplosion hazard NK
Preventivemeasures
Personalprotective equipment Use protective gloves and goggles when handling the product.
First aid
Inhalation – N.A.
Skin contact – wash with water.
Eye contact – rinse immediately with plenty of water. Obtain medical attention.
Ingestion – drink water. If large amounts have been swallowed induce vomiting andobtain medical advice.
Emergency actionin case of fire Extinquish with water, foam, powder or carbon dioxide.
Spillage and Contain, collect and remove for destruction.decontamination Prevent reaching sewage.Internal information by the buyer
1) Classified according to EEC-directive 67/548/EEC and its amendments.
UK and IrelandWilson Tool InternationalStirling RoadSouth Marston Ind. EstateSwindonWiltshire SN3 4XY
UKTel (Free): (0800) 373748Fax (Free): (0800) 373758IrelandTel (Free): (1-800) 709009 Fax (Free): (1-800) 535538
Office:Tel: +44 (0) 1793 831818Fax: +44 (0) 1793 831945Email: [email protected]://www.wilsontool.com
233 / 04/02 TEK
31
Conditions of SaleOrder
Minimum order is £35.
CreditAll orders accepted are subject to approval of our credit department. If youare a new account, please furnish us with a bank reference and threesupplier references. A credit limit will be imposed on new accounts untilcredit has been established.
PaymentTerms are net 30 days.
CancellationIn the event an order is cancelled, a charge will be made to cover labour,material and overheads.
Returned MaterialA handling charge of 25% is made on all standard parts returned for credit.Written permission and shipping instructions must be obtained before thereturn of any material. Special tooling cannot be returned.
ClaimsAll claims for shortages must be made within 10 days of invoice date.
Prices are exclusive of V.A.T., but inclusive packing and specialdelivery to your door within 1 - 5 working days after receipt oforder. Tooling remains the property of Wilson Tool until full payment has been received.
TRUMPF-STYLE Conditions of Sale
V i s i t u s o n t h e w o r l d w i d e w e b a t : h t t p : / / w w w. w i l s o n t o o l . c o mE m a i l : s a l e s @ w i l s o n t o o l . e u . c o m
Tek 04/02
United States12912 Farnham AvenueWhite Bear LakeMN 55110USA
Tel (Free): 800-328-9646Tel: (651) 426-9133Fax: (651) 426-9134Fax (Free): 800-222-0002
United KingdomStirling RoadSouth Marston Industrial EstateSwindonWiltshireSN3 4XYEngland
Tel (Free): 0800-373748Tel: +44 (0)1793 831818Fax: +44 (0)1793 831945 or 46Fax (Free): 0800-373758Tel (Free): 1-800 709009 IrelandFax (Free): 1-800 535538 IrelandEmail:[email protected]
Germ a n yGottlieb-Daimler-Str. 231552 RodenbergDeutschland
Tel (Free): 00800-945-766-8665Tel: 05723-747-0Fax (Free): 00800-945-766-329Fax: 05723-747-10Email: [email protected]
ScandinaviaIslevdalvej 100DK-2610RødovreDenmark
Tel: +45 44 53 16 99Fax: +45 44 53 06 07Email:[email protected]
Freephones
Tel
Fax
Austria
00800 945 766 8665
00800 945 766 329
Belgium
00800 945 766 8665
00800 945 766 329
France
0800 90 84 88
0800 90 85 20
Irish Republic
1-800 709 009
1-800 535 538
Netherlands
00800 945 766 8665
00800 945 766 329
Switzerland
00800 945 766 8665
00800 945 766 329
Reprezentant pentru Romania :
S.C. SM TECH SRL
Tehnologii şi soluţii pentru industria prelucrării tablelor
Tel/Fax: 0040-231-515702 Tel: 0040-745-528494
E-mail: [email protected] www.sm-tech.ro