Dimensions

Width - 126.3cmDepth - 52cmHeight - 184.5cm

Issue 1 - 10/03/10

Important – Please read these instructions fully before starting assembly

If you need help or have damaged or missing parts, call the Customer Helpline: 0870 160 1490

Winchester - 3 Door 4 Drawer WardrobeAssembly Instructions - Please keep for future reference

656/6988656/7035

Safety and Care AdviceImportant – Please read these instructions fully before starting assembly

• Check you have all the components and tools listed on pages 2, 3 and 4.

• Remove all fittings from the plastic bags and separate them into their groups.

• Keep children and animals away from the work area, small parts could choke if swallowed.

• Make sure you have enough space to layout the parts before starting.

• Do not stand or put weight on the product, this could cause damage.

• Assemble the item as close to its final position (in the same room) as possible.

• Assemble on a soft level surface to avoid damaging the unit or your floor.

• Parts of the assembly will be easier with 2 people.

• We do not recommend the use of power drill/drivers for inserting screws,

as this could damage the unit. Only use hand screwdrivers.

• Dispose of all packaging carefully and responsibly.

• When handling mirror care must be taken to ensure it is not knocked or damaged.

• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.

• From time to time check that there are no loose screws on this unit.

• This product should not be discarded with household waste. Take to your local authority waste disposal centre.

Care and maintenance

1

Large drawer front x 2 (71.3 x 19cm)

Bottom panel x 1 (112.3 x 48.6cm)

Components - PanelsPlease check you have all the panels listed below

2

Top panel x 1 (126.3 x 52cm)3

Left side panel x 1 (49.5 x 182.2cm)

2Right side panel x 1 (49.5 x 182.2cm)

1

Back panel x 1 (76.8 x 174.1cm)

5

10

Back panel x 1 (37.5 x 174.1cm)

6

Right hinge frame x 1 (5.3 x 182.2cm)

7

4

Right drawer side x 4 (35 x 10cm)

11 Left drawer side x 4 (35 x 10cm)

12

Left hinge frame x 1 (5.3 x 182.2cm)

8

Large drawer back x 2 (70.6 x 10cm)

13

Bottom plinth x 1 (105.4 x 5.3cm)

9

Handle x 9 (10.5 x 1.9cm)15Large drawer base x 2 (71 x 33.9cm)

14

If you have damaged or missing components, call the Customer Helpline: 0870 160 1490

Vertical partition wall x 1 (48.4 x 171.3 cm)

Components - PanelsPlease check you have all the panels listed below

Small horizontal partition shelf x 1 (35.7 x 48.4cm)

17

22

Small drawer back x 2 (31.3 x 10cm)

18

Small drawer front x 2 (37 x 19cm)

19

Large horizontal partition shelf x 1 (75 x 48.4cm)

16

Right door x 1 (37 x 132cm)23 Middle mirror door x 1 (37 x 132cm)

24

Small drawer base x 2 (31.7 x 33.9cm)

20

Left door x 1 (37 x 132cm)25

Shelf x 2 (35.6 x 47.6cm)21

Right side

3

Please check you have all the fittings listed below

Feet x 4

Tools required

A

Screw x 48

E

8/30mm Wooden dowel x 48

B

Small locking nut x 8

H

6/30mm Wooden dowel x 16

C

Key x1

R

L

I

Drawer base support x 4

Q

Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.

Ruler - Use this ruler to help correctly identify the screws

100 20 30 40 50 60 70 80 90 100

0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 110 115 120 125 130 135 140 145 150 155 160 165 170105

Hanger rail support x 2

Hanger rail x 1 14mm Screw x 2 Door stop x 1

V

9mm Screw x 16

F

Door hinge x 6 Wall strap x 1Hinge plates x 6

13mm Screw x 1 12mm Screw x 8

W

Nail x 50

D

20mm Screw x 16

K

Underlay x 2

ORunner left B x 4

M

P

Runner right B x 4

N

Shelf support x 8U

X

Z ZZY Z

Runner left A x 4

L

Large locking nut x 40

G

Plastic dowel x 16

J

50mm Screw x 3

R

Runner right A x 4

S

35mm Screw x 18

T

Components - Fittings

Phillips screwdriver (medium & large)

Flatblade screwdriver (medium)

Hammer

Spirit level

2 34

Ruler/tape measure

4

Attaching runners

a: Position runners T 15mm in from front edge of the left side panel 1 .

Slide top of the runners back.

Fix through holes shown using screws C .

Assembly InstructionsStep 1

Attaching runners

a: Position left runner A L and right runner A R on to the drilled holes of the left and right side panels 1 and 2 and the left side of vertical partition wall 22 .

Fix through holes shown using screws F and Z 4.

4

a:

c:

E

E

B

E

E

E

1

2

3

22

R

R

F

L

221

2

A

E

Left side

LF

b: Right side

R

b: Turn over the vertical partition wall 22 and attach runners A L as shown using screws F and Z 4.

c: Attaching feet

Position plastic feet A to the left and right side panels 1 , 2 from below and fix them using the hammer.

F

22

5

L

Z 4

Z 4

Preparation for the attaching of horizontal partition shelf and bottom panel

Insert screws E into the drilled holes of the left and right side panels 1 and 2 , top panel 3 and vertical partition wall (from both sides) 22 and fix them.

Insert wooden dowels B into the bottom panel 4 as shown on the picture.

Step 2

Attaching runners

a: Position runners T 15mm in from front edge of the left side panel 1 .

Slide top of the runners back.

Fix through holes shown using screws C .

Assembly Instructions

Attaching horizontal partition shelves to the vertical partition wall

Insert wooden dowels B into the vertical partition wall 22 , place horizontal partition shelves 16 , 17 on to the screws E , align correctly and insert large locking nuts G into the drilled holes and turn them clockwise to lock.

Step 3

16

22

17

B

G

G

Step 4

a: Place bottom panel 4 to the partition wall

22 and screw the screws Q using the key I . Align correctly and insert large locking nuts G .

b: Insert wooden dowels B into the bottom panel 4 and partition shelves

16 17 and place left and right side panels 1 , 2 . Align correctly

and insert large locking nuts G and turn them clockwise to lock.

a:

b:

6

B

11 mm

Q

I

G

G

16

2

1

22

1617

417

B

B

22

4

Q

G

G

Attaching runners

a: Position runners T 15mm in from front edge of the left side panel 1 .

Slide top of the runners back.

Fix through holes shown using screws C .

Assembly Instructions

Frame assembly

Insert screws E in to the frames 7 , 8 , 9 .

Insert wooden dowels B as shown, align correctly and insert large locking nuts G in to the frame 9 , place the frames 7 , 8 and turn them

clockwise to lock.

Step 67

9

8

E

E

7

8

E

Step 5

9

E

E

G

G

B

B

G

B 11 mm

7

Attaching runners

a: Position runners T 15mm in from front edge of the left side panel 1 .

Slide top of the runners back.

Fix through holes shown using screws C .

Assembly InstructionsStep 7

Step 8

Step 9

Attaching top panel

Insert wooden dowels B into the top edges as shown, align correctly and insert large locking nuts G into left and right side panels 1 and 2 and vertical partition wall 22 , place the top panel 3 and turn locking nuts

clockwise to lock.

Attaching back panels

With help, carefully lay wardrobe down.

Position back panels 5 , 6 in position on

the back of wardrobe. Position nails D 5 mm in from side edge of the back panels 5 , 6 with distance 100 mm between each other. Fix them using the hammer.

2

D

5 mm

100 mm

6

8

5

1

G

G

B

1

3

2G

22

G

4

Note: You must ensure the wardrobe is square before attaching the back panels.

B

11 mm

B

11 mm

Attaching the frame

Insert wooden dowels B into the edge of the left and right side panels 1 , 2 .

Align correctly and insert large locking nuts G into left and right side panels 1 , 2 and bottom panel 4 , place the frame

and turn locking nuts clockwise to lock.

B

B

Attaching runners

a: Position runners T 15mm in from front edge of the left side panel 1 .

Slide top of the runners back.

Fix through holes shown using screws C .

Assembly InstructionsStep 10

Drawer assembly

a: Insert screws E into large or small drawer front 10 , 19 .

b: Insert wooden dowels B in to large or small drawer front 10 , 19 . and place left and right drawer sides 11 , 12 .

c: Slide large or small drawer base 14 , 20 iinto the grooves.

d: Place large or small drawer back 13 , 18 onto sides.

e: Align correctly and insert small locking nuts H into left and right drawer sides 11 , 12 and turn them clockwise to lock.

f: Insert plastic dowels J into left and right

drawer sides 11 , 12 and large or small drawer back 13 , 18 and fix it together using the hammer.

g: Position left and right runners B M , N on to left and right drawer sides 11 , 12 , fix using screws K .

10

14

13

K

M

N

K

J

JH

a: b:

c: d:

e: f:

g:

E

12 12

12

12

11 11

11

11

1313

K

K

19

2018

18

18

11

12

B

1910

continued on next page

9

Attaching runners

a: Position runners T 15mm in from front edge of the left side panel 1 .

Slide top of the runners back.

Fix through holes shown using screws C .

Assembly Instructions

Attaching hanger rail

Insert hanger rail supports U and place the hanger rail Z .

Fitting hinges to doors and door stop

Position 2 hinge plates V into left and right side panels 1 , 2 and partition wall 22 . Fix using supplied screws.

Position door stop Z 3 onto the underside of the top panel 3 , fix using screws Z 2.

Step 11

Placing shelves

With help, carefully stand wardrobe upright.

Warning: The wardrobe is heavy. Lift with care.

Position shelf supports T and place the shelves 21 .

Step 12

Step 13

P

S

15

15

S S

Z

U

10

h: i:

T21

V

1

222

P

P

T

Z

Z

3

h: Large drawers only: Position 2 drawer base supports P onto the underside of the large drawers as shown. Fix using supplied screw.

i: All drawers: Attach handles 15 to drawer fronts using screws S .

2

3

32 mm

Step 10 - continued

Attaching runners

a: Position runners T 15mm in from front edge of the left side panel 1 .

Slide top of the runners back.

Fix through holes shown using screws C .

Assembly Instructions

W

Hanging doors

With help, slot door hinges W onto hinge plates V and click into position.

Repeat for all doors.

Hinge adjustment

To move doors up or down, in or out, left or right: loosen screws as shown and move doors up or down, in or out, left or right as required.

Retighten screws.

Step 14

Position 2 door hinges W into left, middle mirror and right doors 23 , 24 , 25 , fix using supplied screws.

Step 15

Attaching handles to the doors

Attach handles 15 to doors 23 , 24 , 25 using screws S .

Repeat this step with all doors 23 , 24 , 25 .

Step 16

Step 17

25

15

24 23

S

V

click!

25 24 23W

Warning: The mirror door. Handle with care.

Warning: The mirror door. Handle with care.

11

Attaching runners

a: Position runners T 15mm in from front edge of the left side panel 1 .

Slide top of the runners back.

Fix through holes shown using screws C .

Assembly Instructions

Fix wall strap X to top of wardrobe using screw Y and underlay O .

Assembly is complete.

Fixing to wall

It is recomended that the wardrobe is fixed to a wall.

Mark fixing hole onto wall. Drill a hole and insert a suitable wall plug. Fix wall strap X using a suitable screw.

With help, move wardrobe into position.

Step 18

Inserting drawers

Insert the drawers with the move from down to up as shown and ensure that wheels fit onto left and right runners L , R .

Step 19

O

Y

X

12

If you need help or have damaged or missing parts, call the Customer Helpline: 0870 160 1490

Home Retail Group Plc, 489 - 499 Avebury boulevard, Milton Keynes, MK9 2NW

Warning: The wardrobe is heavy. Lift with care.

Warning: Before drilling, check wall for hidden pipes and cables.

Note: Wall fixings are not supplied with this unit.

The correct type of fixing must be used for your wall, seek professional advice if in doubt.

RL

X