Soft Drawn Solid or Stranded 600 Volt UL 90°C THHN/THWN Insulation Copper Conductor Application: For use on insulators for overhead distribution circuits or for grounding conductors. Conductor: Soft bare annealed copper per ASTM B-3, Class B stranding per ASTM B-8. Tin-coated soft, mediumhard, or hard drawn copper wire also available upon request. Additional Standards: Federal Specification CID A-A-59551 (non-insulated) soft drawn bare copper Soft Drawn Bare Copper - Solid AF000 0801S 8 16510 Solid .12 50 AF000 0601S 6 26240 Solid .16 79 AF000 0401S 4 41740 Solid .20 126 AF000 0201S 2 66360 Solid .25 201 Soft Drawn Bare Copper - Stranded AF000 01401 14 4110 7 .07 13 AF000 01201 12 6530 7 .09 20 AF000 01001 10 10380 7 .11 32 AF000 00801 8 16510 7 .14 51 AF000 00601 6 26240 7 .18 81 AF000 00401 4 41740 7 .23 129 AF000 00201 2 66360 7 .29 205 AF000 00101 1 83690 19 .33 258 AF000 10101 1/0 105600 19 .37 326 AF000 20101 2/0 133100 19 .41 411 AF000 30101 3/0 167800 19 .47 518 AF000 40101 4/0 211600 19 .52 653 AF000 25001 250 250000 37 .57 772 AF000 35001 350 350000 37 .68 1081 AF000 50001 500 500000 37 .81 1544 AF000 75001 750 750000 61 .99 2316 AF000 10001 1000 1000000 61 1.15 3088 Catalog No. Size AWG/kcmil No. of Strands Cross Sectional Area Circular Mils Overall Diameter Inch Net Weight Lbs/Mft Application: For use in general wiring applications for lighting and power in conduits, ducts, or other approved raceways with maximum conductor temperature of 90°C in dry locations and 75°C in wet locations. Chemical,gasoline and oil resistant. Conductor: Soft bare annealed copper per ASTM B-3, Class B stranding per ASTM B-8. Insulation: Heat and moisture resistant PVC per UL Standard 83. Specification Jacket: Clear Nylon per UL Standard 62. Flame Test: UL VW-1 Additional Standards: • Federal Specification CID A-A-55543 • UL 1063 (Type MTW for stranded items) • UL 758 (Type AWM 105°C dry, 80°C in oil) WIRE & CABLE Building & Bare Cu Wire www.afielektrik.com F 01 AF001 01401 14 19 15 4 .12 16 AF001 01201 12 19 15 4 .14 25 AF001 01001 10 19 20 4 .17 39 AF001 00801 8 19 30 4 .23 66 AF001 00601 6 19 30 5 .25 98 AF001 00401 4 19 40 6 .33 155 AF001 00301 3 19 40 6 .36 190 AF001 00201 2 19 40 6 .39 235 AF001 00101 1 19 50 7 .45 300 AF001 10101 1/0 19 50 7 .50 370 AF001 20101 2/0 19 50 7 .54 460 AF001 30101 3/0 19 50 7 .60 570 AF001 40101 4/0 19 50 7 .66 710 AF001 25001 250 37 60 8 .72 845 AF001 35001 350 37 60 8 .83 1165 AF001 50001 500 37 60 8 .96 1640 AF001 75001 750 61 70 9 1.17 2480 AF001 10001 1000 61 70 9 1.32 3300 Catalog No. Size AWG/kcmil No. of Strands PVC Insulation Thickness Mils Nylon Jacket Thickness Mils Overall Diameter Inch Net Weight Lbs/Mft
Transcript
Soft DrawnSolid or Stranded
600 Volt UL 90°CTHHN/THWN InsulationCopper Conductor
Application:For use on insulators for overhead distributioncircuits or for grounding conductors.Conductor:Soft bare annealed copper per ASTM B-3,Class B stranding per ASTM B-8. Tin-coatedsoft, mediumhard, or hard drawn copper wirealso available upon request.Additional Standards:Federal Specification CID A-A-59551 (non-insulated)
Application:For use in general wiring applications for lightingand power in conduits, ducts, or other approvedraceways with maximum conductor temperatureof 90°C in dry locations and 75°C in wet locations.Chemical,gasoline and oil resistant.Conductor:Soft bare annealed copper per ASTM B-3, ClassB stranding per ASTM B-8.Insulation:Heat and moisture resistant PVC per UL Standard83. SpecificationJacket:Clear Nylon per UL Standard 62.Flame Test:UL VW-1Additional Standards:• Federal Specification CID A-A-55543• UL 1063 (Type MTW for stranded items)• UL 758 (Type AWM 105°C dry, 80°C in oil)
APPLICATIONSRomex Type NM-B (nonmetallic-sheathed cable) may be used for both exposed and concealed work in normally dry locationsat temperatures not to exceed 90°C(with ampacity limited to that for 60°C conductors) as specified in the NationalElectrical Code. NM-B cable is primarily used in residential wiring as branchcircuits for outlets, switches, and otherloads. NM-B cable may be run in air voids of masonry block or tile walls where such walls are not wet or damp locations.Voltage rating for NM-B cable is 600 volts.SPECIFICATIONSRomex Type NM-B cable meets or exceeds UL Standard 83, UL Standard 719, Federal Specification A-A-59544,and requirements of the National Electrical Code.CONSTRUCTIONRomex Type NM-B cable is manufactured as 2, 3, or 4 conductor cable, with a ground wire. Copper conductors are annealed (soft) copper. Stranded conductorsare compressed stranded. Conductor insulation is 90°C-rated polyvinyl chloride (PVC), nylon jacketed. The cable jacket is color-coded for quick size identification;White - 14 AWG, Yellow -12 AWG, Orange - 10 AWG, and Black - 8 AWG and 6 AWG.
TWO CONDUCTOR14 2 1 19 14 1 360 X 162 57 15 EH12 2 1 19 12 1 410 X 179 82 20 EH10 2 1 24 10 1 494 X 210 124 30 EH8 2 1 35 10 1 612 X 269 186 40 BK6 2 1 35 10 1 683 X 304 255 55 BK
NOTE 1: Single conductor. Subject to special inquiry.†Not more than 3 conductors in cable per Table 310.16,National Electrical Code, 2005 Edition.
STANDARD PACKAGE CODESB – 1000 ft. reelC – 500 ft. reelE – 1000 ft. spoolH – 250 ft. coilK – 125 ft. coil
A P P L I C A T I O N S Suitable for use as follows:• Colonial Type UF-B cable is generally used as feeder to outside post lamps, pumps, and other loads or apparatus fed from a distribution point in an existingbuilding as specified in the National Electrical Code1• UF-B cable may be used underground, including direct burial• Multiple conductor UF-B cable may be used for interior branch circuit wiring in residential or agricultural buildings at conductor temperatures not to exceed90°C (with ampacity limited to that for 60°C conductors) as specified by the National ElectricalCode• UF-B can be used in applications permitted for NMC in Section 334.10(B) of the National Electrical Code. Voltage rating for UF-B cable is 600 voltsS T A N D A R D S & R E F E R E N C E SColonial Type UF-B cable meets or exceeds UL Standard 83, UL Standard 493, Federal Specification A-A-59544, and requirements of the National Electrical Code.C O N S T R U C T I O N• Colonial Type UF-B cable is manufactured as a 2 or 3 conductor cable, with or without a ground wire• Copper conductors are annealed (soft) copper, solid or compressed stranded• Phase conductors are polyvinyl chloride (PVC) insulated, nylon jacketed, color coded for identification purposes• Jacketed with sunlight, moisture and fungus resistant gray PVCS P E C I F I C A T I O N SCable shall be UL-listed Type UF-B, suitable for operation at 600 volts or less in all installations as specified in the National Electrical Code.Conductors shall be annealed copper manufactured by Southwire Company or approved equal.
SIZE/CONST.(AWG)
NUMBEROF
STRANDS
INSULATION& JACKET
THICKNESS(mils)
JACKETTHICKNESS
(mils)
MULTIPLE CONDUCTOR
GROUND WIREWITHOUT GROUND
NUMBEROF
STRANDSSIZE
(AWG)
WITH GROUND
CABLEDIMENSION
(mils)
APPROX. NETWEIGHT PER1000 FT.(lbs)
CABLEDIMENSION
(mils)
APPROX. NETWEIGHT PER1000 FT.(lbs)
ALLOWABLEAMPACITY†
STANDARDPACKAGE
CONDUCTOR
W E I G H T S , M E A S U R E M E N T S A N D P A C K A G I N G
2 CONDUCTOR14 1 19 30 14 1 423 X 168 71 354 X 168 53 15 EQ12 1 19 30 12 1 463 X 183 97 386 X 183 71 20 EQ10 1 24 30 10 1 518 X 215 140 440 X 215 104 30 EQ6 7 35 45 10 1 678 X 302 223 576 X 302 178 40 CK8 7 35 45 10 1 770 X 338 304 668 X 338 256 55 CK
3 CONDUCTOR14 1 19 30 14 1 581 X 168 97 501 X 168 78 15 EQ12 1 19 30 12 1 626 X 183 131 581 X 183 110 20 BQ10 1 24 30 10 1 727 X 215 194 661 X 215 159 30 BQ6 7 35 45 10 1 1059 X 319 345 984 X 319 304 40 CK8 7 35 45 10 1 1223 X 361 480 1153 X 361 438 55 CK
UF - B
WIRE & CABLEUnderground Feeder Cable
+Ampacity per 310.15 and 334.80, National Electrical Code, 2008 edition.NOTE: Jacket thickness for all NM-B cable is 30 mils.*Color Code for 2/2 Conductor Cable is Black, White, Red, and White with Red Stripe.**Color Code for 4 Conductor Cable is Black, White, Red, and Blue.
18 AWG Types CL2, MP, CM, and FPL• 20 AWG Type CL2 Only, PVC/PVC,Plastic Jacketed (PJ) 20 and 18 AWGFEATURES• OSHA acceptable• UL listed• CL2 – Power Limited per Article 725• CM – Communication Cables per Article 800• FPL – Power Limited Fire Protective Signaling Cable per Article 760• Solid bare copper per UL-13• PVC insulation per UL-13• Sunlight resistant PVC jacket per UL-13• CSA CertifiedAPPLICATIONDesigned for indoor use in heating and air conditioning controls, bell and alarm systems.Color Code:2-conductor laid flat: Red, White Multi-conductor cabled round: Red, White, Green, Blue, Yellow, Tan, Orange, Black, Pink,BrownSurface Print:20 AWG: “Sun Res CL2 90°C 20 (UL)---CSA CMG FT4” 18 AWG: “Sun Res CL2 or CM or FPL 90°C 18 A.I.W. Corp. (UL)---CSA CMG FT4”
Note: CL2 can be used for CL2X and FPL can be used for CL3.
FEATURES• UL listed (file no. E18966)• OSHA acceptable• Bunch stranded copper conductors• Sunlight and water resistant grade PVC insulation (black)• Polarity ridge on one conductor for identification• CSA certified (file no. LL 8825)APPLICATIONDesigned for outdoor use above and below ground in landscape lighting and securitysystems. Also available in colors or as 3/C upon request.Indent print: “(size) 2/C Underground Low Energy Circuit Cable Sunlight Resistant forOutdoor Lighting (UL) E18966---LL8825 CSA low voltage landscape lighting 30V FT1"
600 Volt UL Type TC THHN or THWN Insulation PVC Jacket Copper Conductors copper conductor binder tape
Application:General purpose cable for use in power,control and lighting circuits in a broad rangeof commercial and industrial applications.Approved for installation indoors or outdoors,aerially, in conduits, ducts, cable trays ordirect burial in circuits not exceeding 600volts.May be used in NEC Class I and II,Division 2 hazardous locations. UL approvedfor use in continuous operation at 75°C in wetlocations, 90°C in dry locations, 130°C foremergency overload conditions, and 250°Cfor short circuit conditions.Conductors:Soft bare annealed copper per ASTM B-3, Class B stranding per ASTM B-8.Insulation:Flame-retardant PVC per UL Standard 83for Type THHN or THWN wire.Insulation Jacket:Clear nylon per UL Standard 83 forType THHN or THWN wire.Jacket:Sunlight-resistant PVC per UL Standard 1277.Flame Tests:• IEEE 383 70,000 BTU/hr flame test• ICEA 210,000 BTU/hr flame testColor Code:ICEA Method 1, Table E-2
* Flat construction
Application:General purpose cable for use in power,control and lighting circuits in a broad rangeof commercial and industrial applications. Approved for installation indoors or outdoors,aerially, in conduits, ducts, cable trays or directburial in circuits not exceeding 600 volts. Maybe used in NEC Class I and II, Division 2hazardous locations. UL approved for use incontinuous operation at 75°C in wet locations,90°C in dry locations, 130°C for emergencyoverload conditions, and 250°C for short circuitconditions.Conductors:Soft bare annealed copper per ASTM B-3,Class B stranding per ASTM B-8.Insulation:Flame-retardant PVC per UL Standard 83 forType THHN or THWN wire.Insulation Jacket:Clear nylon per UL Standard 83 for TypeTHHN or THWN wire.Jacket:Sunlight-resistant PVC per UL Standard 1277.Flame Tests:• IEEE 383 70,000 BTU/hr flame test• ICEA 210,000 BTU/hr flame test
600 Volt UL Type TC THHN or THWN Insulation PVC JacketCopper Conductors copper conductor binder tape
F 04
www.afielektrik.com
Tray Cable - Control Cable
Tray Cable - Power Cable
Additional Standards:• UL Type TC per Article 336 of the NEC.• Approved for Class 1 remote-control andsignaling circuits per Article 725 of the NEC.
Additional Standards:• UL Type TC per Article 336 of the NEC.• Approved for Class 1 remote-control andsignalingcircuits per Article 725 of the NEC.
Color Code:ICEA Method 1, Table E-2
WIRE & CABLETray Cable
600 Volt UL Type TC THHN or THWN Insulation PVC Jacket Copper Conductors
Application:General purpose cable for use in power,control and lighting circuits in a broadrange of commercial and industrial applications.Approved for installation indoors or outdoors,aerially, in conduits, ducts, cable trays ordirect burial in circuits not exceeding 600volts. May be used in NEC Class I and II,Division 2 hazardous locations. UL approvedfor use in continuous operation at 75°C in wetlocations, 90°C in dry locations, 130°C foremergency overload conditions, and 250°Cfor short circuit conditions.
* Flat construction
Application:General purpose cable for use in primarypower and feeder circuits in a broad rangeof commercial and industrial applications.Approved for installation indoors or outdoors,aerially, in conduits, ducts, cable trays or directburial in circuits not exceeding 600 volts. May beused in NEC Class I and II, Division 2 hazardouslocations. UL approved for use in continuousoperation at 75°C in wet locations, 90°C in drylocations, 130°C for emergency overload conditions,and 250°C for short circuit conditions.
Jacket:Sunlight-resistant PVC per UL Standard 1277.Flame Tests:• IEEE 383 70,000 BTU/hr flame test• ICEA 210,000 BTU/hr flame testColor Code:ICEA Method 1, Table E-2Additional Standards:• UL Type TC per Article 336 of the NEC.• Approved for Class 1 remote-controland signalingcircuits per Article 725 of the NEC.
Jacket:Sunlight-resistant PVC per UL Standard1277.Flame Tests:• IEEE 383 70,000 BTU/hr flame test• ICEA 210,000 BTU/hr flame testColor Code:ICEA Method 4Additional Standards:UL Type TC per Article 336 of the NEC.
Application:General purpose cable for use in primary powerand feeder circuits in a broad range of commercialand industrial applications. Approved for installationindoors or outdoors, aerially, in conduits, ducts,cable trays or direct burial in circuits not exceeding600 volts. May be used in NEC Class I and II,Division 2 hazardous locations. UL approved foruse in continuous operation at 75°C in wetlocations, 90°C in dry locations, 130°C foremergency overload conditions, and 250°C forshort circuit conditions. Conductors: Soft bareannealed copper per ASTM B-3, Class Bstranding per ASTM B-8.Insulation:Flame-retardant PVC per UL Standard83 for Type THHN or THWN wire.
Flame Tests:• IEEE 383 70,000 BTU/hr flame test• ICEA 210,000 BTU/hr flame testColor Code:ICEA Method 4Additional Standards:UL Type TC per Article 336 of the NEC.
Tray Cable - Control Cable
Tray Cable - Power Cable
Tray Cable - Power Cable
Conductors:Soft bare annealed copper per ASTM B-3,Class B stranding per ASTM B-8.Insulation:Flame-retardant PVC per UL Standard 83for Type THHN or THWN wire.Insulation Jacket:Clear nylon per UL Standard 83 for TypeTHHN or THWN wire.
Conductors:Soft bare annealed copper per ASTM B-3, Class Bstranding per ASTM B-8.Insulation:Flame-retardant PVC per UL Standard 83for Type THHN or THWN wire.Insulation Jacket:Clear nylon per UL Standard 83 for TypeTHHN orTHWN wire.Grounding Conductor:Soft bare annealed copper per ASTMB-3, Class B stranding per ASTM B-8sized in accordance with UL Standard 1277.
Insulation Jacket:Clear nylon per UL Standard 83for Type THHN or THWN wire.Grounding Conductor:Soft bare annealed copperper ASTM B-3, Class B stranding per ASTMB-8 sized in accordance with UL Standard 1277.Jacket:Sunlight-resistant PVC per UL Standard 1277.
