WOOD GAZEBO with ALUMINUM rOOF
Installation and Operating Instructions – YM12705X
Yardistry – North AmericaToll Free Customer Support: 1.888.509.4382
Yardistry / Selwood Products – EuropeCustomer Support: +44 1284 852569
Revised 11/02/2015
12'-1 5/32"
3687.1
12'-1 5/32"
3687.1
HEIGHT:10’6” or 3.2m
Important Safety Notice!
Yardistrycomponentsareintendedforprivacy,decorativeandornamentaluseonly.
Product is NOT INTENDED for the following: •Asafetybarriertopreventunsupervisedaccesstopools,hottubs,spasorponds. •Asloadbearingsupportforabuilding,structure,heavyobjectsorswings. •Usedinstructuresthattrapwind,rainorsnowthatwouldcreateextraloadonthe
product.
Accumulated snow must be removed from roof.
DO NOT climborwalkonroofforanyreason.
Permanent structures may require a building permit. Asthepurchaserandorinstallerofthisproductyouareadvisedtoconsultlocalplanning,zoningandbuildinginspectiondepartmentsforguidanceonapplicablebuildingcodesand/orzoningrequirements.
Wood is NOT flame retardant and will burn.Grills,firepitsandchimineasareafirehazardifplacedtooclosetoaYardistrystructure.Consultuser’smanualofthegrill,firepitorchimneaforsafedistancesfromcombustiblematerials.
Wear gloves to avoid injuryfrompossiblesharpedgesofindividualelementsbeforeassembly.
During installation, follow all safety warnings provided with your tools and use OHSA approved safety glasses.Somestructuresmayrequiretwoormorepeopletoinstallsafely.
Check for underground utilities before digging or driving stakes into the ground!
It is important during assembly to closely follow the instructions,completetheassemblyonasolidlevelsurfaceandthatyoufollowtheinstructiontosquareup,levelandanchorthestructure,thiswillreducethegapatwoodconnectionsduringassembly.
General Information:WoodcomponentsaremanufacturedwithCedar(C.Lanceolata)whichisprotectedwithfactoryappliedwater-basedstain.Knots,smallchecks(cracks)andweatheringarenaturallyoccurringanddonotaffectthestrengthoftheproduct.Annualapplicationofawater-basedwaterrepellentsealantorstainisimportantandwillhelpreduceweatheringandchecks.
www.yardistrystructures.com
Questions?
Calltollfreeorwriteusat:1(888)509-4382
PatentsPending
General Information
Limited WarrantyYardistry warrants that this product is free from defect in materials and workmanship for a period of one year from the original date of purchase. In addition, all lumber is warranted for 5 years against rot and decay. This warranty applies to the original owner and registrant and is non-transferable.
Regular maintenance is required to assure the integrity of your product and is a requirement of the warranty. This warranty does not cover any inspection cost.
This Limited Warranty does not cover:• Labor for replacement of any defective item(s);• Incidental or consequential damages;• Cosmetic defects which do not affect performance or integrity;• Vandalism; improper use or installation; acts of nature;• Actsofnatureincludingbutnotlimitedtowind,storms,hail,floods,excessivewater exposure;• Minor twisting, warping, checking, or any other natural occurring properties of wood that do not affect performance or integrity.
Yardistryproductshavebeendesignedforsafetyandquality.Anymodificationsmadetotheoriginal product could damage the structural integrity of the product leading to failure and possibleinjury.Yardistrycannotassumeanyresponsibilityformodifiedproducts.Furthermore,modificationvoidsanyandallwarranties.
This product is warranted for RESIDENTIAL USE ONLY. Yardistry disclaims all other representations and warranties of any kind, express or implied.
This Warranty gives you specific legal rights. You may have other rights as well which vary from state to state or province to province. This warranty excludes all consequential damages, however, some states do not allow the limitation or exclusion of consequential damages, and therefore this limitation may not apply to you.
Instructions for Proper Maintenance
YourYardistrystructureisdesignedandconstructedofqualitymaterials.Aswithalloutdoorproductsitwillweatherandwear.Tomaximizetheenjoyment,safetyandlifeofyourstructureitisimportantthatyou,theowner,properlymaintainit.
Symbols:Throughouttheseinstructionssymbolsareprovidedinthetop,right-handcornerofthepage.
If you dispose of your Yardistry structure: Pleasedisassembleanddisposeofyourunitsothatitdoesnotcreateanyunreasonablehazardsatthetimeitisdiscarded.Besuretofollowyourlocalwasteordinances.
HARDWARE:• Checkmetalpartsforrust.Iffound,sandandrepaintusinganon-leadpaintcomplying
with16CFR1303.• Inspectandtightenallhardwareaftercompletionofassembly;afterfirstmonthofuse;and
thenannually.Donotover-tightenastocausecrushingandsplinteringofwood.• Checkforsharpedgesorprotrudingscrewthreads,addwashersifrequired.
WOODPARTS:• Applyingawaterrepellentorstain(water-based)onayearlybasisisimportant
maintenancetomaintainmaximumlifeandperformanceoftheproduct.• Checkallwoodmembersfordeterioration,structuraldamageandsplintering.Sanddown
splintersandreplacedeterioratedwoodmembers.Aswithallwood,somecheckingandsmallcracksingrainisnormal
• Somegappingmayoccuratsomewoodconnections.
• TapeMeasure• CarpentersLevel• StandardorCordlessDrill• #2PhillipsBitorScrewdriver• 7/16”&9/16”Wrench
Assembly Guides
• 8’StepLadder• SafetyGlasses• AdultHelper• SafetyGloves• HardHat
Tools Required:
• UseHelp,wherethisisshown,2,3or4peoplearerequiredtosafelycompletethisstep.Toavoidinjuryordamagetotheassemblymakesuretogetsomehelp.
• Useameasuringtapetoassureproperlocation
• Pre-drillapilotholebeforefasteningscreworlagtopreventsplittingofwood.
• 6’StepLadderx2• Square• Rachet• 7/16,1/2&9/16Socket
Followingaresomehelpfultipstomaketheassemblyprocesssmoothandefficient.
PRE-ASSEMBLIES:(i.e.PostandBeamAssemblies,RoofRafterAssembly,etc)• Workonaraised,solidandflatsurfacesuchas,atableorsawhorse.• Keepallconnectionsflushwhereshownintheinstructions.• Whenassemblingthebeamskeeppartsflat,straightandsnugwhen
connecting.
METALPARTS:
• Roofingmaterialmayhavesharpedges,wearsafetygloves.• Removeplasticcoveringonbothsidesofthemetalpanelsdirectlybefore
installingeachpiece.• Placeroofingmaterialonanon-abrasivesurfacebeforeandafterassembly
asitcanbend,dentandscratcheasily.• Theroofingscrewscaneasilycrushtheroofpanelsandroofedgeswhen
usingapowerdrill.Werecommendhandtighteningtheroofingscrewssotheysitsnugandtighttotheroofingmaterial.
Assembly Tips
Note: It is critically important you start with square, solid and level footings, concrete pad or deck to attach your Pergola Room.
WesupplyPostMountswiththisstructurewhichgivesyoutheflexibilitytopermanentlyinstallyourstructuretoapre-existingornewwoodorconcretesurface.• ThehardwaretoattachthePostMounttothestructureisincluded.• Thehardwaretomountthestructurepermanentlywillneedtobepurchasedseparatelyatyourlocal
hardwarestore.
Ifyouaremountingtoconcretefootersseebelowforthecorrectlocationsandplacement.Pleasedoublecheckforpossibilityofanyundergroundutilitiessuchasgas,telephone,cableorsprinklerlines.
Followingaresomeexamplesofhowtomountthestructuretowoodorconcretesurfaces.
Refertoyourlocalbuildingandcitycodes,ordinances,neighbourhoodcovenants,orheightrestrictionsregardingthistypeofstructureforguidanceonacceptableinstallationrequirements.
Permanent Installation Examples
Concrete Footer
ToRequiredDepth
AnchoringHardwarenotincludedPostMount
13’11”PosttoPostPosttoPost
11’0”
PlinthtoPlinth9’8-1/8”
PosttoPost11’0”
PlinthtoPlinth9’8-1/8”
Permanent Installation Examples cont.
Concrete Patio (min. 11’ 6” x 11’ 6”) with 6” clearance on all sides
Wood Deck (min. 11’ 6” x 11’ 6”) with 6” clearance on all sides
AnchoringHardwarenotincluded
AnchoringHardwarenotincluded
PostMounts
AnchoringHardware(notincluded)
PostMounts
Roof
To
Post
Bra
cket
(4x)
Roof
to B
eam
Bra
cket
(X12
)(4
X)Ra
fter S
hort
Righ
t FSC
(338
)(4
X)St
rap
Shor
t FSC
(337
)
(4x)
7
x 7
Post
FSC
(324
)
(4X)
Gus
set L
eft F
SC (3
31)
Gus
set R
ight
FSC
(330
)(4
x)
(16X
)
(8X)
Post
Mou
nt
Plin
th F
SC (3
29)
Bea
m E
nd L
eft F
SC (3
44)
(4X)
Rafte
r Sho
rt Le
ft FS
C (3
39)
Rafte
r Cor
ner R
ight
FSC
(334
)(4
X)(8X)
(4X)
(4x)
Bea
m F
SC (3
43)
Bea
m E
nd R
ight
FSC
(345
)
(x4)
Rafte
r Cor
ner L
eft F
SC (3
33)
(4x)
(4X)
Stra
p FS
C (3
36)
Rafte
r FSC
(340
)(4
X)
Bea
m E
nd S
hort
FSC
(344
)
Fasc
ia L
eft F
SC (3
41)
(4X)
Fasc
ia R
ight
FSC
(342
)(4
X)
Roof
Pea
k Br
ack
et (2
X)
1/4"
Nut
Ca
rria
ge B
olt (
Squa
re S
houl
der
)
Pea
k C
ap
Pea
k Po
st
Pea
k Lo
op
Sprin
g C
lip
Roof
Ed
ge L
eft (
4X)
Righ
t Sho
rt Pa
nel (
4X)
Roof
Ed
ge R
ight
(4X)
Left
Shor
t Pan
el (4
X)
Left
Long
Pan
el (4
X)
Righ
t Lon
g Pa
nel (
4X)
Rid
ge C
lip (8
X)
Cor
ner C
ap (4
X)
Rid
ge C
ap (4
X)
Wea
ther
Sea
l - R
idge
Clip
(8X)
(7 x 7 x 94")
Y70219-324
7 x 7 Post FSC 4pc. (324) -177.8 x 177.8 x 2387.6mm
(5/4 x 6 x 8-7/8")
Plinth FSC
Y50219-329
16pc. (329) -23.8 x 133.4 x 225.4mm
Part Identification ( ) Dimensions are approximate and are shown to assist in the identification of parts for assembly. Actual dimensions may be smaller or larger.
(1-1/4 x 3 x 41-13/16")31.8 x 76.2 x 1062mm Rafter Short Left FSC 4pc. (339) -
Y50219-339
(1-1/4 x 3 x 41-13/16")31.8 x 76.2 x 1062mm Rafter Short Right FSC 4pc. (338) -
Y50219-338
(1 x 3-1/2 x 103-13/16")
Y50219-334
Rafter Corner Right FSC 4pc. (334) -25.4 x 88.9 x 2631.5mm
Y50219-333
Rafter Corner Left FSC 4pc. (333) -25.4 x 88.9 x 2631.5mm (1 x 3-1/2 x 103-13/16")
(1-1/4 x 3 x 76-1/4")31.8 x 76.2 x 1937.1mm Rafter FSC 4pc. (340) -
Y50219-340
Y50219-337 Strap Short FSC 4pc. (337) -
31.8 x 82.6 x 1561.3mm (1-1/4 x 3-1/4 x 61-7/16")
(1-1/4 x 3-1/4 x 103-7/16")
Y50219-336
Strap FSC 4pc. (336) -31.8 x 82.6 x 2628.1mm
(1-1/4 x 3-1/4 x 73-1/2")
Y50219-342
Fascia Right FSC 4pc. (342) -31.8 x 82.6 x 1866.9mm
(1-1/2 x 7-1/2 x 39-1/2")38.1 x 190.5 x 1003.3mm
Gusset Right FSC 4pc. (330) -
Y70219-330
(1-1/4 x 3-1/4 x 73-1/2")
Y50219-341
Fascia Left FSC 4pc. (341) -31.8 x 82.6 x 1866.9mm
(1-1/2 x 5-1/2 x 70-1/2") Beam End Right FSC
Y50219-345
4pc. (345) -38.1 x 139.7 x 1790.7mm
(1-1/2 x 5-1/2 x 70-1/2") Beam End Left FSC
Y50219-344
4pc. (344) -38.1 x 139.7 x 1790.7mm
(1-1/2 x 5-1/2 x 23")
Beam End Short FSC
Y50219-346
8pc. (346) -38.1 x 139.7 x 584.2mm
(1-1/2 x 5-1/2 x 95") Beam FSC
Y50219-343
4pc. (343) -38.1 x 139.7 x 2413mm
(1-1/2 x 7-1/2 x 39-1/2")38.1 x 190.5 x 1003.3mm
Gusset Left FSC 4pc. (331) -
Y70219-331
Hardware Identification ( )Dimensions are approximate and are shown to assist in the identification of parts for assembly. Actual dimensions may be smaller or larger.
68pc. 5/16" Flat Washer (Y05118-203)
96pc. Wood Screw #8 x 2 1/2" - (52043522)
1pc. #2 x 2" Robertson Driver (9200014)
1pc. - 1/8 " Drill B
it(Y
00 400-002 )
8pc. - 3/8" Lock Nut(Y08318-803)
44pc. 5/16 - T-Nut (Y08518-300)
40pc. Pan Screw #10 x 1-1/4" (52443911)
16pc. 5/16" Lock Washer (Y05318-300)
16pc. Hex Bolt 5/16 x 3-3/4" - (Y07718-333)
16pc. 3/8" Flat Washer (Y05118-801)
8pc. Lag Screw 5/16 x 4-3/4" - (Y06218-343)
3/8 x 10-1/2"8pc. Hex Bolt
(Y07718-812)
22pc. Pan Screw #8 x 1" (52433510)
40pc. Wood Screw #6 x 1" (52013910)
4pc. Wafer Bolt 5/16 x 1" (Y07618-310)
24pc. Wafer Bolt 5/16 x 1-3/8" (Y07618-316)
200pc. Hex Roofing Screw #8x 1"
(Y06728-510)
24pc. Sheet Metal Screw #8 x 3/4"
(Y06428-503)
1pc. - Hex Driver(Y00400-004)
1pc. - 3/16" Hex Key - (Y00400-003)16pc. Wafer Lag 1/4 x 2-1/2" - (Y06618-222)
144pc. Wood Screw #8 x 1-1/2" (52043512)
56pc. Wood Screw #8 x 2 1/4" - (52043521)
12pc. Hex Bolt 1/4 x 2-3/4" - (Y07718-223)
12pc. - 1/4" Lock Nut(Y08318-203)
24pc. Pan Screw #12 x 1-1/4" (52433611)
24pc. 1/4" Large Washer (Y05118-211)
Dimensions are approximate and are shown to assist in the identification of parts for assembly. Actual dimensions may be smaller or larger.Hardware Identification ( )
1pc. - Roof Set(Y70828-084)
1pc. - Roof Peak Set(Y70828-068)
4pc.Ridge Cap
(Y01028-060)
4pc. - Left Short Panel(Y01028-062)
4pc. - Left Long Panel(Y01028-064)
1pc. - Gazebo ID Plaque (Y70800-104)
4pc. - Right Short Panel(Y01028-063)
4pc. - Right Long Panel(Y01028-065)
1pc. - Corner Cap Set (4Pk) (Y70828-073)
8pc.Ridge Clip
(Y01028-061)
4pc.Roof Edge Left(Y01028-066)
4pc.Roof Edge Right
(Y01028-067)1pc.
Peak Cap(Y01028-071)
1pc.Peak Post
(Y01028-072)
1pc. - Weather Seal - Ridge Clip (8Pk) (Y70818-074)
1pc. - Roof To Beam Bracket Set (12Pk)
(Y70828-102)
1pc. - Roof To Post Bracket Set (4Pk)
(Y70828-070)
1pc. - Post Mount Set (8Pk) (Y70819-057)
2pc.Roof Peak Bracket
(Y00428-068)
1pc.Carriage Bolt(Y07428-260)
1pc.1/4" Nut
(Y08490-200)1pc.Spring Clip
(Y09490-001)1pc.
Peak Loop(Y20018-003)
1pc. - 50mm Hook(2Pk)
(Y70818-075)
PRODUCTNUMBER:YM12705XCARTONI.D.STAMP:_____________(Box1)
CARTONI.D.STAMP:_____________(Box2)
CARTONI.D.STAMP:_____________(Box3)
STOP STOPSTOP STOP
C. Readtheassemblymanualcompletely,payingspecialattentiontoANSIwarnings;notes;andsafety/maintenanceinformationonpages1-4.
•Followtheinstructionsinorder. •Thisstructureisdesignedtobeassembledandinstalledideallybyfourpeople,
DONOTattempttoinstallalone. •Considertheslopeofelevationwhereyouplantoinstallthestructure.Also,checkfor
gas,telephone,otherutilitiesorsprinklerlinelocationspriortoexcavatinganyholes.
D. Beforeyoudiscardyourcartonsfillouttheformbelow.
•ThecartonI.D.stampislocatedontheendofeachcarton. •Pleaseretainthisinformationforfuturereference.Youwillneedthisinformationifyou
contacttheConsumerRelationsDepartment.
•Eachstepindicateswhichboltsand/orscrewsyouwillneedforassembly,aswellasanyflatwashers,lockwashers,t-nutsorlocknuts.
A. Thisisthetimeforyoutoinventoryallyourhardware,woodandaccessories,referencingthepartsidentificationsheets.Thiswillassistyouwithyourassembly.
Step 1: Inventory Parts - Read This Before Starting Assembly
B. Ifthereareanymissingordamagedpiecesoryouneedassistancewithassemblypleasecontacttheconsumerrelationsdepartmentdirectly.Callusbeforegoingbacktothestore.
Step 2: Post Assemblies
HardwareWood Parts
Fig. 2.1
A:Atthebottomofone(324)7x7PostplacetwoPostMountstighttothebottomandinsidefacesasshowninfig.2.1and2.2.Attachwithtwo#10x1-1/4”PanScrewspermountfromtheinsideandtwo#8x2-1/2”WoodScrewsperbracketfromtheoutside.
B:Placeone(329)PlinthflushtothebottomandtighttothePostMountsoneachsideofthe(324)7x7Postandattachwithfour#8x1-1/2”WoodScrewsperplinth.Roundededgesontop.(fig.2.1,2.2and2.3)
C:RepeatStepsAandBthreemoretimestomakefourPostAssemblies.
(329)Plinth
Tight
4 x (324) 7 x 7 Post 177.8 x 177.8 x 2387.6 mm (7 x 7 x 94”)16 x (329) Plinth 23.8 x 133.4 x 225.4 mm (5/4 x 6 x 8-7/8”)
16 x #10 x 1-1/4” Pan Screw16 x #8 x 2-1/2” Wood Screw64 x #8 x 1-1/2” Wood Screw8 x Post Mount
Top
Bottom
#8x2-1/2”WoodScrews(x2perPostMount,fromoutside)
#8x1-1/2”WoodScrews(x4perPlinth)
(324)7x7Post
PostMount
(324)7x7Post
Fig. 2.2
(329)Plinth
#10x1-1/4”PanScrews(x2perPostMount,frominside)
RoundedEdgeonTop
Fig. 2.3
RoundedEdgeonTop
Step 3: Beam Assembly Part 1
HardwareWood Parts
A:Connectone(344)BeamEndLeftandone(345)BeamEndRightusingtwo5/16x1-3/8”WaferBolts(with5/16”flatwasherand5/16”t-nut)asshowninfig.3.1and3.2.
B:Connectone(346)BeamEndShorttoeachendofone(343)Beamusingtwo5/16x1-3/8”WaferBolts(with5/16”flatwasherand5/16”t-nut)perendasshowninfig.3.1and3.2.
C:RepeatStepsAandBthreemoretimestomakefourBeamShortAssembliesandfourBeamEndAssemblies.
(344)BeamEndLeft
4 x (344) Beam End Left 38.1 x 139.7 x 1790.7 mm (1-1/2 x 5-1/2 x 70-1/2”)4 x (345) Beam End Right 38.1 x 139.7 x 1790.7 mm (1-1/2 x 5-1/2 x 70-1/2”)8 x (346) Beam End Short 38.1 x 139.7 x 584.2 mm (1-1/2 x 5-1/2 x 23”)4 x (343) Beam 38.1 x 139.7 x 2413 mm (1-1/2 x 5-1/2 x 95”)
Fig. 3.1
24 x 5/16 x 1-3/8” Wafer Bolt (5/16” flat washer, 5/16” t-nut)
Fig. 3.2
5/16”FlatWasher
5/16x1-3/8”WaferBolt
5/16”T-nut
Tight
(345)BeamEndRight
(343)Beam
(346)BeamEndShort
(346)BeamEndShort
QRcodegeneratedonhttp://qrcode.littleidiot.be
http://bit.ly/1EALDEx
Hardware
72 x #8 x 2-1/2” Wood Screw
Fig. 3.3
BeamShortAssembly
Fig. 3.4
Flush
BeamEndAssembly
Step 3: Beam Assembly Part 2
D:PlaceoneBeamShortAssemblyononeBeamEndAssemblysotheendsareflush.Matchtheboltholesineach(346)BeamEndShortwiththeboltholesin(344)BeamEndLeftand(345)BeamEndRight.Attachwith18#8x2-1/2”WoodScrews.(fig.3.3and3.4)
E:RepeatStepDthreemoretimestomakefourBeamAssemblies.
Flush
BeamShortAssembly
BeamEndAssembly
#8x2-1/2”WoodScrews(x18perassembly)
(344)BeamEndLeft
(345)BeamEndRight
(346)BeamEndShort
(346)BeamEndShort
Match bolt holes
Step 4: Frame Assembly and Anchoring Part 1
Fig. 4.1
A: MoveyourPostAssembliestothefinallocation.Makesurethegroundisflatandlevelbeforecontinuingassembly.
B:WithonepersonateachPoststandtwocompletePostAssemblies.AthirdpersonplacesoneBeamAssemblyagainsttheoutsideofeachPost,flushtothetopsandoutsidecorners.NoticeboltholeorientationontheBeamAssembly.AfourthpersonattachesBeamtoPostwithone3/8x10-1/2”HexBolt(withtwo3/8”flatwashersandone3/8”locknut)perPost.ThedistancefromtheoutsideofonePosttotheoutsideofthesecondPostshouldbe11’0”.(fig.4.1,4.2and4.3)
C:ContinueuntilallfourBeamAssembliesareattachedandthecornersaretighttogether.(fig.4.1and4.2)Seefig.4.3foraccuratepositioningofPosts.
Fig. 4.2
Hardware8 x 3/8 x 10-1/2” Hex Bolt (3/8” flat washer x 2, 3/8” lock nut)
Note hole orientation (on
bottom)Fig. 4.3
9’8-1/8”
9’8-1/8”
3/8”LockNut
3/8”FlatWasher
3/8”FlatWasher
3/8x10-1/2”HexBolt
3/8x10-1/2”HexBolt
BeamAssembly
BeamAssembly
BeamAssembly
PostAssembly
PostAssembly
PostAssembly
PostAssembly
PlinthtoPlinth
PlinthtoPlinth13’11”
PosttoPost
11’0”PosttoPost
Plinth
Note hole orientation (on
bottom)
QRcodegeneratedonhttp://qrcode.littleidiot.be
http://bit.ly/1KufUGU
D: MakesureeachcornerissquareandlevelthenattachBeamAssembliestoPostAssemblieswithtwo5/16x4-3/4”LagScrews(with5/16”flatwasher)percorner.(fig.4.4)
E:DependingonwhatyouareplacingthePergolaRoomonwilldeterminehowyouanchorittothatsurface.Pleaserefertopages5and6forinstallationexamples.
Any hardware or extra materials for
mounting will have to be purchased in advance.
Hardware8 x 5/16 x 4-3/4” Lag Screw (5/16” flat washer)
5/16”FlatWasher
5/16x4-3/4”LagScrew
5/16x4-3/4”LagScrew
Fig. 4.4
BeamAssembly
BeamAssembly
PostAssembly
Step 4: Frame Assembly and Anchoring Part 2
5/16”FlatWasher
Note: The bevelled ends on each gusset should always face away from the wood it is attaching to.
A:MakesuretheassemblyisstillsquareandlevelthenfacingoneBeamAssemblyplaceone(330)GussetRightontherighthandsidesothetopfitstighttotheBeamAssemblyandthebottomfitstighttothePostAssembly.AttachgussettoBeamAssemblywithtwo5/16x3-3/4”HexBolts(with5/16”lockwasher,5/16”flatwasherand5/16”t-nut)andtoPostAssemblywithtwo1/4x2-1/2”WaferLags(with5/16”flatwasher).(fig.5.1,5.2and5.3)
B: RepeatStepAonthelefthandsidewithone(331)GussetLeft.(fig.5.1,5.2and5.3)
C: RepeatStepsAandBforeachBeamAssembly/PostAssembly.(fig.5.1,5.2and5.3)
D: Ateachcorner,tighttotheoutsideedgesofthejoiningBeamAssembliesattachoneRooftoPostBracketwithtwo#10x1-1/4”PanScrews.(fig.5.3and5.4)
Step 5: Attach Gussets and Roof Brackets
Fig. 5.1
Tight
4 x (330) Gusset Right 38.1 x 190.5 x 1003.3 mm (1-1/2 x 7-1/2 x 39-1/2”)4 x (331) Gusset Left 38.1 x 190.5 x 1003.3 mm (1-1/2 x 7-1/2 x 39-1/2”)
HardwareWood Parts16 x 1/4 x 2-1/2” Wafer Lag (5/16” flat washer)
16 x 5/16 x 3-3/4” Hex Bolt (5/16” lock washer, 5/16” flat washer, 5/16” t-nut)
8 x #10 x 1-1/4” Pan Screw
4 x Roof to Post Bracket
Fig. 5.2
(330)GussetRIght
RooftoPostBracket
#10x1-1/4”PanScrew
(331)GussetLeft
BeamAssembly
PostAssembly
(330)GussetRIght
(331)GussetLeft
BeamAssembly
PostAssembly Beam
Assembly
5/16”FlatWasher
1/4x2-1/2”WaferLag
5/16”T-nut
5/16”LockWasher
1/4x2-1/2”WaferLag
5/16”FlatWasher
5/16x3-3/4”HexBolt
5/16x3-3/4”HexBolt
Fig. 5.3 Fig. 5.4
(330)GussetRIght
(331)GussetLeft
(330)GussetRIght
(331)GussetLeft
(330)GussetRIght
(331)GussetLeft
(330)GussetRIght
(331)GussetLeft
QRcodegeneratedonhttp://qrcode.littleidiot.be
http://bit.ly/1KufUGU
A:Tightlyconnectone(341)FasciaLeftandone(342)FasciaRightusingone5/16x1”WaferBolt(with5/16”flatwasherand5/16”t-nut)asshowninfig.6.1and6.2.
B:RepeatStepAthreemoretimestomakefourFasciaBeamAssemblies.
Step 6: Fascia Beam Assembly
Fig. 6.1
Fig. 6.2
HardwareWood Parts4 x (341) Fascia Left 31.8 x 82.6 x 1866.9 mm (1-1/4 x 3-1/4 x 73-1/2”)4 x (342) Fascia Right 31.8 x 82.6 x 1866.9 mm (1-1/4 x 3-1/4 x 73-1/2”)
4 x 5/16 x 1” Wafer Bolt (5/16” flat washer, 5/16” t-nut)
(342)FasciaRIght
(341)FasciaLeft
(342)FasciaRIght
(341)FasciaLeft
5/16”FlatWasher
5/16”T-nut
5/16x1”WaferBolt
Tight
QRcodegeneratedonhttp://qrcode.littleidiot.be
http://bit.ly/1KufXCB
A:Oneachsideofone(340)Rafterplaceone(333)RafterCornerLeftandone(334)RafterCornerRightsothetopsandedgesareflushthenattachwithtwo#8x2-1/4”WoodScrewsperside.(Fig.7.1and7.2)
B:PlaceFasciaBeamAssemblyfromStep6onthebottomof(333)RafterCornerLeft,(334)RafterCornerRightand(340)Raftersothesidesareflushthenattachwithtwo#8x2-1/4”WoodScrewsateachendandtwointhemiddle.(fig.7.1,7.3and7.4)
C:RepeatStepsAandBthreemoretimestomakefourRoofRafterAssemblies.
HardwareWood Parts
#8x2-1/4”WoodScrews(x6perFasciaBeamAssembly)
(340)Rafter
Top View
FasciaBeamAssembly
Step 7: Roof Rafter Assembly Part 1
Fig. 7.1
40 x #8 x 2-1/4” Wood Screw4 x (340) Rafter 31.8 x 76.2 x 1937.1 mm (1-1/4 x 3 x 76-1/4”)4 x (333) Rafter Corner Left 25.4 x 88.9 x 2631.5 mm (1 x 3-1/2 x 103-13/16”)4 x (334) Rafter Corner Right 25.4 x 88.9 x 2631.5 mm (1 x 3-1/2 x 103-13/16”)
Fig. 7.3
Fig. 7.4
Note notches facing up
Flush
FasciaBeamAssembly
FasciaBeamAssembly
Flush
(340)Rafter
(340)Rafter
#8x2-1/4”WoodScrews
#8x2-1/4”WoodScrews
Flush
Fig. 7.2
(333)RafterCornerLeft
(333)RafterCornerLeft
(333)RafterCornerLeft
(334)RafterCornerRight
(334)RafterCornerRight
Front View
Front View
Note angle side up
QRcodegeneratedonhttp://qrcode.littleidiot.be
http://bit.ly/1KufXCB
HardwareWood Parts
#8x1-1/2”WoodScrewsx20perassembly
Fig. 7.5
Step 7: Roof Rafter Assembly Part 2
80 x #8 x 1-1/2” Wood Screw16 x #8 x 2-1/4” Wood Screw
4 x (337) Strap Short 31.8 x 82.6 x 1561.3 mm (1-1/4 x 3-1/4 x 61-7/16”)4 x (336) Strap 31.8 x 82.6 x 2628.1 mm (1-1/4 x 3-1/4 x 103-7/16”)4 x (338) Rafter Short Right 31.8 x 76.2 x 1062 mm (1-1/4 x 3 x 41-13/16”)4 x (339) Rafter Short Left 31.8 x 76.2 x 1062 mm (1-1/4 x 3 x 41-13/16”)
D:Placeone(337)StrapShortinthenotchesof(333)RafterCornerLeft,(334)RafterCornerRightand(340)Raftersotheendsdonotoverhangtheoutsideedgesoftheoutsideboardsthenattachwithsix#8x1-1/2”WoodScrews.(Fig.7.5)
E:Placeone(336)Strapinthenotchesof(333)RafterCornerLeft,(334)RafterCornerRightand(340)Raftersotheendsdonotoverhangtheoutsideedgesoftheoutsideboards.Donotattachyet.(fig.7.5)
F:Placeone(338)RafterShortRightandone(339)RafterShortLeftinthenotchesof(336)Strapandattachasshowninfig.7.5withfour#8x1-1/2”WoodScrewsandtwo#8x2-1/4”WoodScrewsperboard.
G:Attach(336)Strapto(333)RafterCornerLeft,(334)RafterCornerRightand(340)Rafterwithsix#8x1-1/2”WoodScrews.(fig.7.5)
H:CompleteStepsD,E,FandGforallfourRoofRafterAssemblies.
(340)Rafter
NoOverhang
FasciaBeamAssembly
Flush
(333)RafterCornerLeft
(334)RafterCornerRight
Front View
Flush
(337)StrapShort
(339)RafterShortLeft
(336)Strap
(338)RafterShortRight
#8x2-1/4”WoodScrews
#8x2-1/4”WoodScrews
Hardware
Centred and flush to bottom of rafters
#8x1”PanScrew
RooftoBeamBracket
Fig. 8.1
Fig. 8.2
A:OntheBackofthethreeRoofRafterAssemblies,centredandflushtothebottomof(338)RafterShortRight,(339)RafterShortLeftand(340)RafterattachoneRooftoBeamBracketperboardwithone#8x1”PanScrewinthebottomholeandone#12x1-1/4”PanScrewinthetopholeperbracket.OneRoofRafterAssemblywillnothavebrackets.(fig.8.1and8.2)
Step 8: Attach Roof to Beam Brackets
9 x #8 x 1” Pan Screw
9 x #12 x 1-1/4” Pan Screw
9 x Roof to Beam Bracket
Back View
(340)Rafter
(339)RafterShortLeft
(338)RafterShortRight
FasciaBeamAssembly
FasciaBeamAssembly
#12x1-1/4”PanScrew
INSTALLING ROOFING MATERIAL
CAUTION! Roofing material may have sharp edges! Wear gloves!
HANDLE WITH CARE!Place roofing material on a non-abrasive surface before assembly
as it can bend, dent and scratch easily.
WARNING – DO NOT OVER TIGHTEN ROOFING SCREWS!Over tightening screws will cause roofing material to crush.
The roofing screws can easily crush the Roof Panels and Roof Edges when using a power drill.Werecommendhandtighteningtheroofingscrewssothattheysitsnugandtighttotheroofingmaterial.
STOP STOPSTOP STOP
OvertightenedandCrushed SnugandTight
X
Hardware
#8x1”RoofingScrews
Step 9: Attach Roof Panels Part 1
A:PlaceoneLeftLongPanelonthefrontofoneRoofRafterAssemblysoitisflushtothesideof(333)RafterCornerLeftandaslightoverhangatthebottomoftheFasciaBeamAssembly.Holesshouldlineupwith(340)Rafter.(fig.9.1and9.2)
B: PlaceoneRightLongPanelonRoofRafterAssemblysoitoverlapstheLeftLongPanelanditisflushtothesideof(334)RafterCornerRightandaslightoverhangatthebottomoftheFasciaBeamAssembly.(fig.9.1and9.2)
C: AttachbothLeftandRightLongPanelstoRoofRafterAssemblywithfour#8x1”RoofingScrewsinlocationsshowninfig.9.1.Besurenottoovertightenscrews.
D: RepeatStepsA-CforallfourRoofRafterAssemblies.
Fig. 9.1
Fig. 9.2
16 x #8 x 1” Roofing Screw
Roof Parts4 x Left Long Panel4 x Right Long Panel
Front View
FasciaBeamAssembly
(333)RafterCornerLeft
(334)RafterCornerRight
Top, Side View
Panels overlap at the seams
(340)Rafter
(334)RafterCornerRight
(333)RafterCornerLeft
#8x1”RoofingScrews
LeftLongPanel RightLong
Panel
DO NOT overtighten screws, could cause damage to roofing
material
FlushFlush
Slightoverhang
Lower 3 screws may have to be removed in next step to properly place Left and
Right Short Panels
Flush
QRcodegeneratedonhttp://qrcode.littleidiot.be
http://bit.ly/1J1kaQt
Fig. 9.4
Fig. 9.3
Hardware
116 x #8 x 1” Roofing Screw
Roof Parts4 x Left Short Panel4 x Right Short Panel
Step 9: Attach Roof Panels Part 2
E:PlaceoneLeftShortPanelonRoofRafterAssemblysoitoverlapstheLeftLongPanelanditisflushtothesidesof(333)RafterCornerLeftandaslightoverhangatthebottomoftheFasciaBeamAssembly.Thereshouldbenooverhangingatthecorners.(fig.9.3and9.4)
F: PlaceoneRightShortPanelonRoofRafterAssemblysoitoverlapstheRightLongPanelanditisflushtothesideof(334)RafterCornerRightandaslightoverhangatthebottomoftheFasciaBeamAssembly.Thereshouldbenooverhangingatthecorners.(fig.9.3and9.4)
G: AttachallpanelstoRoofRafterAssemblywith29#8x1”RoofingScrewsinlocationsshowninfig.9.3.Donotplaceanyscrewsalongthebottomrow.Besurenottoovertightenscrews.
H: RepeatStepsE-GforallfourRoofRafterAssemblies.
(333)RafterCornerLeft(hidden) (334)Rafter
CornerRight(hidden)
(340)Rafter(hidden)
#8x1”RoofingScrews(x29perassembly)
LeftLongPanel
RightLongPanel
LeftShortPanel
RightShortPanel
Panels flush to corners, no overhang
Panels overlap at the seams
FasciaBeamAssembly
FasciaBeamAssembly No screws along bottom row
DO NOT overtighten screws, could cause damage to roofing
material
Tight at centre
Step 10: Attach Ridge Clips and Roof Edges
Hardware
Fig. 10.1
68 x #8 x 1” Roofing Screw40 x #6 x 1” Wood Screw
A:PlaceoneRoofEdgeLeftandoneRoofEdgeRightonthebottomofeachRoofRafterAssemblysotheendsareflushwiththeoutsideendsoftheFasciaBeamAssemblyandmeettightinthecentre.AttachbothRoofEdgeswith17#8x1”RoofingScrewsperRoofRafterassembly.(fig.10.1and10.2)
B:PlaceoneWeatherSealontheinsideofeachRidgeClipthenplaceoneRidgeCliponeachsideofeachRoofRafterAssemblysotheycoverthepanelsandattachwithfive#6x1”WoodScrewsperRidgeClip.(fig.10.1,10.3and10.4)
WeatherSeal
RidgeClip
Fig. 10.2
#6x1”WoodScrews(x5perside)
Panels
Componets:4 x Roof Edge Left 4 x Roof Edge Right8 x Ridge Clip8 x Weather Seal
RidgeClip
RoofEdgeLeft
RoofEdgeRight
FasciaBeamAssembly
Flush
Flush
#8x1”RoofingScrews(x17)
RoofEdgeLeft
RoofEdgeRight
FasciaBeamAssembly
Fig. 10.3WeatherSeal
Underneath, Side View
RidgeClip
Fig. 10.4Side View
#6x1”WoodScrews(x5perside)
RidgeClip
Flush
A:FrominsideofPostAssembliesmeasure4’11”tomarkthecentreofeachBeamAssembly.(fig.11.1)
B:WithallfourassemblersplaceoneRoofPanelAssemblywithRooftoBeamBracketsjustinfrontofthePostAssembliesthenraiseitupsothemiddleRooftoBeamBracketislinedupwiththecentremark.(fig.11.1and11.2)
Step 11: Attach Roof Panels to Frame Part 1
Fig. 11.1
In front of Post
Assembly
BeamAssembly
PostAssembly
4’11”
RoofPanelAssembly
Mark centre location
Mark centre location
Mark centre location
x3
BeamAssembly
RooftoBeamBracket
Fig. 11.2
BeamAssembly
Line middle bracket to centre mark
One assembler to support roof panel(s) at all times until
secure
QRcodegeneratedonhttp://qrcode.littleidiot.be
http://bit.ly/1J1kcYq
Step 11: Attach Roof Panels to Frame Part 2
Fig. 11.4
RooftoBeamBracket
C:LiftasecondRoofPanelAssemblywithRooftoBeamBracketsoverBeamAssemblytakingcarenottodragthepanelonthebeams.MakesurethemiddleRooftoBeamBracketlinesuptothecentremarkandtheRafterCornersareflushwitheachother.One person must remain on the centre ladder to hold both panels in place until three panels are up and secure. (fig.11.2,11.3and11.4)
D:StartingatthebottomandworkingupconnectRoofPanelAssembliesthroughtheRafterCornerswiththree1/4x2-3/4”HexBolts(withtwo1/4”largewashersandone1/4”locknut).Toalignboltholeshelperinthecentremayhavetopushupthecentreofthepanelsandothersmakesurecornersarealigned.Makesureallboltsaretight.(fig.11.2and11.5)
Fig. 11.2
Flush
Fig. 11.3
BeamAssembly
x3
Line middle bracket to centre mark
RafterCorners
Fig. 11.5
Hardware
3 x 1/4 x 2-3/4” Hex Bolt (1/4” large washer x 2, 1/4” lock nut)
RafterCorner
1/4”LockNut
1/4x2-3/4”HexBolt
RoofPanelAssembly
Make sure corners are aligned
RoofPanelAssembly
Start at bottom and work up the rafters
1/4”LargeWasher
One assembler to support roof panel(s) at all
times until secure
Fig. 11.6
E:LiftthirdRoofPanelAssemblywithRooftoBeamBracketsoverBeamAssemblytakingcarenottodragthepanelonthebeamsthensetinplacebesidethesecondpanel.MakesurethemiddleRooftoBeamBracketlinesuptothecentremark.(fig.11.6)
F:StartingatthebottomandworkingupconnectRoofPanelAssembliesthroughtheRafterCornerswiththree1/4x2-3/4”HexBolts(withtwo1/4”largewashersandone1/4”locknut).Toalignboltholeshelperonthecentreladdermayhavetopushupinthecentreofthepanelsandothersmakesurecornersarealigned.Makesureallboltsaretight.(fig.11.7)
RoofPanelAssembly
Fig. 11.7
Hardware
3 x 1/4 x 2-3/4” Hex Bolt (1/4” large washer x 2, 1/4” lock nut)
Step 11: Attach Roof Panels to Frame Part 3
x3
RafterCorner
RoofPanelAssembly
1/4”LargeWasher1/4”Lock
Nut
1/4x2-3/4”HexBolt
PeakCap
CarriageBolt
PeakLoop
SpringClip
1/4”Nut
A:InsertCarriageBoltthroughthetopofPeakCap,intoPeakPostthenSpringClip.TheSpringClipholdstheassemblytogether.(fig.12.1)
B:Insert1/4”NutintoPeakLoop.BecarefulnutislooseandwillfalloutuntilattachedtoPeakCapAssembly.(fig.12.2)
Fig. 12.1
PeakPost
Componets:1 x Roof Peak Set 1 x Carriage Bolt 1 x Peak Loop 1 x Spring Clip 1 x 1/4”Nut
1 x Peak Cap1 x Peak Post
Step 12: Roof Peak Assembly
Fig. 12.2
PeakCap
CarriageBolt
Fig. 13.3
PeakLoop
A:InsertRoofPeakAssemblyingapbetweenRoofPanels.PeakCaptobelinedupwithRafterCorners.(fig.13.1and13.2)
B:InsertbothRoofPeakBracketsthroughCarriageBoltandattachPeakLooptoCarriageBoltandtwisttotightenloosely.
C: LooselyattachbothRoofPeakBracketstotheRafterCornersintheslottedholeswithtwo#10x1-1/4”PanScrewsasshowninfig.13.3.
Fig. 13.1
RoofPeakBracket
RoofPeakAssemlby
Components:2 x Roof Peak Brackets
Step 13: Attach Roof Peak to Roof Panels x3
RafterCorners
RafterCornersRafter
Corners
Fig. 13.2
RafterCorner
RoofPeakBracket
#10x1-1/4”PanScrewx2
RafterCorner
RafterCorner
Hardware
2 x #10 x 1-1/4” Pan Screw
Fig. 14.2
Fig. 14.1
A:LiftlastRoofPanelAssembly(withoutRooftoBeamBrackets)overBeamAssemblytakingcarenottodragthepanelonthebeams.PanelfitsunderthePeakCap,pushuponPeakLooptoliftPeakCap.Thecentreoftheotherpanelsmayhavetobepusheduptofitfourthpanel.(fig.14.1and14.2)
B:CheckagainthatPeakCapislinedupwithRafterCorners.(fig.14.3)
RoofPanelAssembly
PeakCap
RoofPanelAssembly
Step 14: Attach Final Roof Panel Part 1
x3
RafterCorners
PeakCap
RoofPanelAssembly
RafterCorners
Fig. 14.3
QRcodegeneratedonhttp://qrcode.littleidiot.be
http://bit.ly/1NDtZox
Remember to push up centre to assist with alignment.
C:StartingatthebottomandworkinguplooselyconnectRoofPanelAssembliesthroughtheRafterCornerswiththree1/4x2-3/4”HexBolts(withtwo1/4”largewashersandone1/4”locknut)perside.Toalignboltholeshelperonthecentreladdermayhavetopushupinthecentreofthepanelsandothersmakesurecornersarealigned.Tightenboltswhenallsixhavebeeninstalled.(fig.14.4and14.5)
Rafter Corners should be aligned with Roof to Post Bracket.
RafterCorner
Hardware6 x 1/4 x 2-3/4” Hex Bolt (1/4” large washer x 2, 1/4” lock nut)
1/4”LargeWasher1/4”Lock
Nut
1/4x2-3/4”HexBolt
Fig. 14.4
Fig. 14.5
RoofPanelAssembly
Bottom holes first
x3Step 14: Attach Final Roof Panel Part 2
D:OnthefourthRoofRafterAssembly,centredandflushtothebottomof(338)RafterShortRight,(339)RafterShortLeftand(340)RafterattachoneRooftoBeamBracketperboardwithone#8x1”PanScrewinthebottomholeandone#12x1-1/4”PanScrewinthetopholeperbracket.(fig.14.6)
x3
Fig. 14.6
Parts removed for clarity
RooftoBeamBracket
#12x1-1/4”PanScrew
Flush
AttachtoRafterShortRight,RafterShortLeftandRafter
#8x1”PanScrew
Hardware3 x #8 x 1” Pan Screw
3 x #12 x 1-1/4” Pan Screw
3 x Roof to Beam Bracket
Step 14: Attach Final Roof Panel Part 3
Hardware8 x #8 x 2-1/2” Wood Screw
8 x #8 x 1” Pan Screw
A:MakesuremiddleRooftoBeamBracketsarelinedupovercentremarkandallareflushandtighttotheBeamAssemblies.Liftincentreifneeded.
B:FromoutsidetheassemblyattachRoofPanelAssembliestogetherattheFasciaBeamAssemblyEndswithtwo#8x2-1/2”WoodScrewspercorner.Ahelpermayneedtoliftthecentreoftherooftobringthecornerstighttogether.(fig.15.1and15.2)
C:AlignRoofPanelAssembliestositcentredonRooftoPostBracketsthenattachwithtwo#8x1”PanScrewsperbracket.(fig.15.3)
#8x1”PanScrew
Fig. 15.1
Fig. 15.2
FasciaBeamAssembly
FasciaBeamAssembly
FasciaBeamAssembly
FasciaBeamAssemblyRooftoPost
Bracket
#8x2-1/2”WoodScrew
#8x2-1/2”WoodScrew
FasciaBeamAssembly
Fig. 15.3
Step 15: Secure Roof Cornersx3
QRcodegeneratedonhttp://qrcode.littleidiot.be
http://bit.ly/1NDtZox
A:AteachcornerplaceoneCornerCaptighttoFasciaAssemblies,pushupsothebottomistighttothebottomoftheassembliesthenattachwithfour#8x3/4”SheetMetalScrewsperCornerCap.(fig.16.1and16.2)
Hardware
16 x #8 x 3/4” Sheet Metal Screw
Componets:
4 x Corner Cap
CornerCap
FasciaAssembly
Fig. 16.1
Fig. 16.2
#8x3/4”SheetMetalScrew
FasciaAssembly
Tight
x3
Step 16: Attach Corner and Beam Caps
#8x3/4”SheetMetalScrew
A:FrominsidetheassemblyattachRooftoBeamBracketstoBeamAssemblieswithone#12x1-1/4”PanScrewperbracket.(fig.17.1and17.2)
Hardware12 x #12 x 1-1/4” Pan Screw
x3
Step 17: Secure Roof to Beam Brackets
Inside ViewBeamAssembly
Fig. 17.1RoofPanelAssembly
Fig. 17.2RooftoBeamBracket
#12x1-1/4”PanScrew
BeamAssembly
Step 18: Secure Roof Peak Brackets
A:TightenthetwoscrewsinRoofPeakBracketsthenattachtoCornerRaftersintheremainingholeswithfourteen#10x1-1/4”PanScrews.(fig.18.1)
Hardware
14 x #10 x 1-1/4” Pan Screw
Fig. 18.1
RoofPeakBracket
RafterCorner
RoofPeakBracket
RafterCorner
RafterCorner
RafterCorner
#10x1-1/4”PanScrewx14
Step 19: Attach Ridge Caps to Roof Panels
A:SlideoneRidgeCapovertheRidgeClips,withcutendleading,oneachcorneroftheassemblyfromthebottomup,liftingPeakCapbypushingupthePeakLoopsoRidgeCapsfitunderPeakCapthenattachwithtwo#8x3/4”SheetMetalScrewsperRidgeCap.(fig.19.1,19.2and19.3)
B: TightenLooptosecureRoofPeakSet.
Hardware
8 x #8 x 3/4” Sheet Metal Screw
Componets:
4 x Ridge Cap
RidgeCap
RidgeCap
RidgeCap
RidgeClip
#8x3/4”SheetMetalScrew
RidgeCap
Fig. 19.1
Fig. 19.2Fig. 19.3
x3
CutEnd
FoldedEnd
35-1/2”
http://bit.ly/1EALXDf
QRcodegeneratedonhttp://qrcode.littleidiot.be
Step 20: Metal Hooks and Plaque Part 1
A:Two50mmHooksareincludedwiththisunitforattachingwiring.TheycanbeplacedanywherealongtheRafterCornersasneeded.Pre-drillwitha1/8”drillbitbeforeinstalling.(fig.20.1and20.2)
Hardware2 x 50 mm Hooks
Fig. 20.1
Fig. 20.2
RafterCorner
50mmHook
Note: We have provided 2 hooks for optional use to hold in place any wires if required. These hooks are not designed to hold any heavy products such as lights, flower pots, etc.
Step 20: Metal Hooks and Plaque Part 2
B:AttachGazeboIDPlaquetoaprominentlocationonyourgazebowithtwo#8x1”PanScrews.Thisprovideswarningsconcerningsafetyandimportantcontactinformation.Atrackingnumberisprovidedtoallowyoutogetcriticalinformationororderreplacementpartsforthisspecificmodel.(fig.20.3and20.4)
Hardware2 x #8 x 1” Pan Screw
1 x Gazebo ID Plaque
Fig. 20.3
Fig. 20.4
#8x1”PanScrew
GazeboIDPlaque
YARDISTRY Consumer Registration Card
First Name Initial Last Name
Street Apt. No.
City State/Province ZIP/Postal Code
Country Telephone Number
E-Mail Address
Model Name Model Number (Box Labels)
Date Purchase Purchased From
How would you rate this product for quality? Excellent Very Good Average Below Average Poor
How would you rate this product for ease of assembly? Excellent Very Good Average Below Average Poor
How would you rate our instructions? Excellent Very Good Average Below Average Poor
How would you rate the quality of packaging? Excellent Very Good Average Below Average Poor
Would you recommend the purchase of our products to friends and family? Yes No
Comments:
MM / DD / YY
REVISION: 10/18/11
MAIL TO:Yardistry c/o Solowave DesignTM
375 Sligo Road W.Mount Forest, Ontario, CanadaN0G 2L0Attention: Customer Service
CUT
ALO
NG
LIN
E
Yardistry would like to say Thank You for your time and feedback.
