WORKS based on DSR -2014 CIVIL WORKS -...

PART A

CONSTRUCTION OF NEW HOSTEL BLOCK FOR GIRLS

CIVIL WORKS

1.0 Earth Works 323,788

2.0 Concrete Works 719,899

3.0 RCC Works 6,999,127

4.0 Brick Wok 1,023,313

5.0 Marble/Granite Works 21,021

6.0 Wood & PVC Works 2,261,173

7.0 Flooring Works 3,283,681

8.0 Finishing Works 381,116

9.0 Aluminium Works 128,669

10.0 Water Proofing Works 181,293

11.0 R/F Steel 5,060,800

TOTAL CIVIL WORKS 20,383,881

ELECTRICAL WORKS

12.0 LIGHT FIXTURES 155,870

13.0 INTERNAL WIRING 500,460

14.0 COMPUTER WIRING 54,720

15.0 DB's/FLOOR PANEL 326,000

16.0 LT CABLES AND TERMINATIONS 85,060

17.0 DATA CABLE 98,400

18.0 EARTHING 37,950

TOTAL ELECTRICAL WORK 1,258,460

19.0 PLUMBING & SANITARY 569,218

TOTAL CIVIL, ELECTRICAL, PLUMBING 22,211,559

SUMMARY PART - I BOQ for CIVIL WORKS, ELECTRICAL WORKS and PLUMBING

WORKS based on DSR -2014

Signature of EPIL Page - 2 Signature of Bidder


New Girls Hostel building, Ahmedabad

RCC Framed Structure, G+4

1075 sq.mts.

SR.

NO.DSR 2014

ITEM NO.

DESCRIPTION UNIT QTY RATE AMOUNT

1.0 2.000 EARTH WORK

1.0

2.600

Earth work in excavation by mechanical means

(Hydraulic excavator) / manual means over areas

(exceeding 30 cm in depth 1.5 m in width as well as 10

sqm on plan) including disposal of excavated earth, lead

up to 50m and lift up to 1.5 m disposed earth to be

leveled and neatly dressed.

1.1 2.6.1 All kinds of soil cum 467 155.60 72,594

1.22.260

Extra for every additional lift of 1.5 m or part thereof in

1.3 2.26.1 All kinds of soil (1.5 mt to 3.0 mt) cum 392 46.25 18,139

1.4

2.250

Filling available excavated earth (excluding rock) in

trenches, plinth, sides of foundations etc.in layers not

exceeding 20 cm in depth, consolidating each deposited

layer by ramming and watering, lead up to 50 m and lift

up to 1.5 m.

cum 487 112.40 54,730

1.52.340

Supplying chemical emulsion in sealed containers

including delivery as specified.

2.34.1Chlorpyriphos/ Lindane emulsifiable concentrate of

20%

Litre 693 185.95 128,863

1.6

2.35.3

Treatment of soil under existing floors using chemical

emulsion @ one litre per hole, 300 mm apart including

drilling 12 mm diameter holes and plugging with

cement mortar 1 :2 (1 cement : 2 Coarse sand) to match

the existing floor :

2.35.3.1With Chlorpyriphos/Lindane E.C. 20% with 1%

concentration

Sqm 416 118.90 49,462

SUB TOTAL 323,788

2.0 4.000 CONCRETE WORK

Providing and Laying in position cement concrete of

specified grade excluding the cost of centring and

shuttering – All work upto plinth level.

2.14.1.3

1:2:4 (1 cement : 2 coarse sand : 4 graded stone

aggregate 20 mm nominal size)

cum 52 5466.30 284,248

2.2 4.1.8

1:4:8 (1 cement : 4 coarse sand : 8 graded stone

aggregate 40 mm nominal size)

cum 98 4301.15 422,255

0

2.3

4.170

Making plinth protection 50 mm thick of cement

concrete 1:3:6 (1 cement: 3 coarse sand : 6 graded stone

aggregate 20 mm nominal size) over 75mm thick bed of

dry brick ballast 40 mm nominal size, well rammed and

consolidated and grouted with fine sand, including

finishing the top smooth.

Sqm 32 419.30 13,397

Client : NATIONAL INSTITUTE OF DESIGN

Architect: R T & ASSOCIATES PVT LTD.

PART - I BOQ for CIVIL WORKS, ELECTRICAL WORKS and PLUMBING WORKS based on DSR -2014

Executing Agency: Engineering Projects India Ltd. (EPIL)

Project Name:

Type of Structure:

Total Built-up Area:

Signature of EPIL 3 Signature of BIdder


SR.

NO.DSR 2014

ITEM NO.


SUB TOTAL 719,899

3.0 5.000REINFORCED CEMENT CONCRETE WORK

3.15.9

Centring and shuttering including strutting, propping

etc. and removal of form for:

3.1.15.9.1

Foundations, footings, bases of column etc. for mass

concrete.

Sqm 600 196.45 117,870.00

3.2

5.370

Providing and laying in position ready mixed M-25

grade concrete for reinforced cement concrete work,

using cement content as per approved design mix,

manufactured in fully automatic batching plant and

transported to site of work in transit mixer for all leads,

having continuous agitated mixer, manufactured as per

mix design of specified grade for reinforced cement

concrete work, including pumping of R.M.C. from

transit mixer to site of laying , excluding the cost of

centering, shuttering finishing and reinforcement,

including cost of admixtures in recommended

proportions as per IS : 9103 to accelerate/ retard setting

of concrete, improve workability without impairing

strength and durability as per direction of the Engineer -

in - charge.

(Note :- Cement content considered in this item is @

330 kg/cum. Excess/less cement used as per design mix

is payable/recoverable separately).

3.2.1 5.37.1 All Works up to Plinth Level cum 274 6644.60 1,818,215

3.2.2 5.37.2 All Works above Plinth Level upto Floor V Level cum 688 7363.00 5,063,042

SUB TOTAL 6,999,127

4.0 6.000 BRICK WORK

4.0

6.400

Brick work with common burnt clay F.P.S. (non

modular) bricks of class designation 7.5 in

superstructure above plinth level up to floor V level in

all shapes and sizes in :

4.1 6.4.2 Cement mortar 1:6 (1 cement : 6 coarse sand) cum 180 5426.15 976,707

4.2

6.130

Half brick masonry with common burnt clay F.P.S.

(non modular) bricks of class designation 7.5 in

superstructure above plinth level up to floor V level.

4.3 6.13.2 Cement Mortar 1:4 (1 cement : 4 coarse sand) sqm 70 665.80 46,606

SUB TOTAL 1,023,313



SR.

NO.DSR 2014

ITEM NO.


5.0 8.000 MARBLE GRANITE WORKS

8.200

Providing and fixing 18 mm thick gang saw cut, mirror

polished, premoulded and prepolished, machine cut for

kitchen platforms, vanity counters, window sills , facias

and similar locations of required size, approved shade,

colour and texture laid over 20 mm thick base cement

mortar 1:4 (1 cement : 4 coarse sand), joints treated

with white cement, mixed with matching pigment,

epoxy touch ups, including rubbing, curing, moulding

and polishing to edges to give high gloss finish etc.

complete at all levels.

8.2.2 Granite of any colour and shade

8.2.2 Granite of any colour and shade

5.1 8.2.2.2 Area of slab over 0.50 sqm sqm 4 3907.40 15,630

8.300

Providing edge moulding to 18mm thick marble stone

counters,Vanities etc. Inbcluding machine polishing to

edge to give high gloss finish etc. complete as per

design approved by Engineer-in-Charge

5.2 8.3.2 Granite work metre 15 230.55 3,458

5.3

8.500

Extra for providing opening of required size & shape

for wash basins/kitchen sink in kitchen platform, vanity

counters and similar location in marble/stone work

including necessary holes for pillar taps etc .including

rubbing and polishing of cut edges etc. complete.

each 5 386.60 1,933

SUB TOTAL 21,021

6.0 9.000 WOOD AND PVC WORK

Room Doors

9.200

Providing and fixing ISI marked flush door shutters

conforming to IS : 2202 (Part I) decorative type, core of

block board construction with frame of 1st class hard

wood and well matched teak 3 ply veneering with

vertical grains or cross bands and face veneers on both

faces of shutters.

6.19.20.1

35 mm thick including ISI marked Stainless Steel butt

hinges with necessary screws.

sqm 75 2606.45 195,484

6.2

9.240

Extra for providing vision panel not exceeding 0.1 sqm

in all type of flush doors (cost of glass excluded)

(overall area of door shutter to be measured):

9.24.1 Rectangular or square sqm 15 139.40 2,091

6.3

9.530

Providing 40x5 mm flat iron hold fast 40 cm long

including fixing to frame with 10 mm diameter bolts,

nuts and wooden plugs and embeddings in cement

concrete block 30x10x15cm 1:3:6 mix (1cement : 3

coarse sand : 6 graded stone aggregate 20mm nominal

size)

each 111 117.35 13,026



SR.

NO.DSR 2014

ITEM NO.


6.4

9.970

Providing and fixing aluminium tower bolts, ISI

marked, anodised (anodic coating not less than grade 10

as per IS:1868), transparent or dyed to required colour

or shade, with nuts and screws etc. complete

9.97.2 250x10 mm each 37 95.25 3,524

6.5

9.101

Providing and fixing aluminium hanging type floor

door stopper (anodic coating not less than grade 10 as

per IS:1868), transparent or dyed to required colour or

shade, with nuts and screws etc. complete

each 37 37.50 1,388

9.101.1 Single rubber stopper

6.6

9.840

Providing and fixing aluminium extruded section body

tubular type universal hydraulic door closer (having

brand logo with ISI, IS : 3564, embossed on the body,

door weight upto 36 kg to 80 kg and door width from

701 mm to 1000 mm), with double speed adjustment

with necessary accessories and screws etc. complete.

each 5 1043.60 5,218

6.7

9.96

Providing and fixing aluminium sliding door bolts ISI

marked anodised anodic coating not less than grade AC

10 as per IS:1868) transparent or dyed to required

colour or shade, with nuts and screws, etc. complete

9.96.2 250x16 each 176 790.30 139,093

Wooden frames-Toilet (Internal Doors)

6.8

9.100

Providing woodwork in frames of doors, windows,

clerestory windows and other frames, wrought framed

and fixed in position and hold fast lugs or with dash

fasteners of requiired dia & length (hold fast and lugs

shall be paid seperately)

9.1.2 Sal wood (Toilet Internal doors) cum 7 75558.60 528,910

Wooden frames-(All other Doors)

6.9

9.100

Providing woodwork in frames of doors, windows,

clerestory windows and other frames, wrought framed

and fixed in position and hold fast lugs or with dash

fasteners of requiired dia & length (hold fast and lugs

shall be paid seperately)

cum 15 91496.00 1,372,440

SUB TOTAL 2,261,173



SR.

NO.DSR 2014

ITEM NO.


7.0 11.000 FLOORING

11.260

Kota stone flooring over 20 mm (average) thick base

laid over and jointed with grey cement slurry mixed

with pigment to match the shade of the slab including

rubbing and polishing complete with base of 1:4 (1

cement : 4 coarse sand)

Note: For detailed specification for Kota stone flooring

refer ACC II

7.1 11.26.1 25 mm thick sqm 895 1141.40 1,021,553

7.1.1

8.600

Mirror polishing on marble work/granite work/stone

work wherever required to give high gloss finish

sqm 895 212.85 190,501

7.2

11.270

Kota stone slabs 20 mm thick in risers of steps, skirting,

dado and pillars laid on 12 mm (average) thick cement

mortar 1:3 (1 cement 3 coarse sand) and jointed with

grey cement slurry mixed with pigment to match the

shade of the slabs, including rubbing and polishing

complete.

sqm 115 1191.25 136,994

7.2.1

8.600



sqm 115 212.85 24,478

0

7.3

11.430

Fixing glazed/ Ceramic / Vitrified floor tiles with

cement based high polymer modified quick-set tile

adhesive ( Water based ) conforming to IS : 15477,

Adhesive per sqm of tile area, in average 3mm

thickness.

sqm 775 432.85 335,459

7.4

11.470

Providing and laying Vitrified tiles in different sizes

(thickness to be specified by the manufacturer), with

water absorption less than 0.08% and conforming to IS:

15622, of approved brand & manufacturer, in all

colours and shade, in skirting, riser of steps, laid with

cement based high polymer modified quick set tile

adhesive (water based) conforming to IS: 15477, in

average 6 mm thickness, including grouting of joints

(Payment for grouting of joints to be made separately).

11.47.2 Size of Tile 60x60 cm sqm 775 1630.20 1,263,405

MIRROR POLISH ON MOSAIC FLOORING

FOR ROOMS AND PASSAGES

7.5

8.600



a Flooring sq.mts 775.00

b Skirting sq.mts 60

835 212.85 177,730

MOSAIC FLOOR TILES



SR.

NO.DSR 2014

ITEM NO.


7.6 11.440 Crazy ceramic tile flooring, with under layer 12 mm

thick cement mortar 1:4 (1 cement: 4 coarse sand), with

joints not exceeding 5 mm, including filling the gaps

with ordinary cement mixture & mixing with

syntheticpolyester fibre, triangular in shape having

specific gravity of 1.34 to 1.40, cross section size

ranging from 10 to 40 micron & length upto 6 mm ,

mixing fibre @ 125 grams per 50 kg of cement in

cement mortar, including providing and mixing water

proofing material in mortar @ 1 kg per 50 kg

of cement , all complete as per direction of Engineer-in-

charge.

sqm 286 467 133,562

SUB TOTAL 3,283,681

8.0 13.000 FINISHING WORK

13.100 12 mm cement plaster of mix: 0

8.1 13.1.1 1 : 4 (1 Cement : 4 fine sand) sqm 2100 163.35 343,035

8.2 13.370 Whitewashing with lime to give an even shade

13.37.1New work (two or more coats) sq.mts 1500 16.20 24,300

8.313.39

Colour washing such as green, blue or buff to give an

even shade

13.39.1New work (two or more coats) with a coat of white

washing with lime

sq.m 625 22.05 13,781

SUB TOTAL 381,116

9.0 21.000 ALUMINIUM WORK

21.100

Providing and fixing aluminium work for doors,

windows, ventilators and partitions with extruded built

up standard tubular sections/ appropriate Z sections and

other sections of approved make conforming to IS: 733

and IS: 1285, fixing with dash fasteners of required dia

and size, including necessary filling up the gaps at

junctions, i.e. at top, bottom and sides with required

EPDM rubber/ neoprene gasket etc. Aluminium

sections shall be smooth, rust free, straight, mitred and

jointed mechanically wherever required including cleat

angle, Aluminium snap beading for glazing / paneling,

C.P. brass / stainless steel screws, all complete as per

architectural drawings and the directions of Engineer-in-

charge. (Glazing, paneling and dash fasteners to be paid

for separately) :

9.1

21.1.2

For shutters of doors, windows & ventilators including

providing and fixing hinges/ pivots and making

provision for fixing of fittings wherever required

including the cost of EPDM rubber / neoprene gasket

required (Fittings shall be paid for separately)

21.1.2.2Powder coated aluminium (minimum thickness of

powder coating 50 micron)

Kg 150 435.75 65,363



SR.

NO.DSR 2014

ITEM NO.


9.2

21.300

Providing and fixing glazing in aluminium door,

window, ventilator shutters and partitions etc. with

EPDM rubber / neoprene gasket etc. complete as per

the architectural drawings and the directions of engineer-

in-charge. (Cost of aluminium snap beading shall be

paid in basic item):

21.3.2 With float glass panes of 5.50 mm thickness sqm 55 1054.20 57,981

9.3

21.800

Filling the gap in between aluminium frame & adjacent

RCC/ Brick/ Stone work by providing weather silicon

sealant over backer rod of approved quality

as per architectural drawings and direction of Engineer-

in-charge complete.

21.8.1 Upto 5mm depth and 5 mm width metre 60 88.75 5,325

SUB TOTAL 128,669



SR.

NO.DSR 2014

ITEM NO.


10.0 22.000 WATER PROOFING WORK

10.1

22.300

Providing and laying water proofing treatment to

vertical and horizontal surfaces of depressed portions of

W.C., kitchen and the like consisting

of:

(i) Ist course of applying cement slurry @ 4.4 kg/sqm

mixed with

water proofing compound conforming to IS 2645 in

recommended proportions including rounding off

junction of

vertical and horizontal surface.

(ii) IInd course of 20 mm cement plaster 1:3 (1 cement :

3 coarse

sand) mixed with water proofing compound in

recommended proportion including rounding off

junction of vertical and horizontal surface.

(iii) IIIrd course of applying blown or residual bitumen

applied hot at 1.7 kg. per sqm of area.

(iv) IVth course of 400 micron thick PVC sheet.

(Overlaps at joints of PVC sheet should be 100 mm

wide and pasted to each

other with bitumen @ 1.7 kg/sqm).

The rate includes preparation of surface, treatment and

sealing of all joints, corners, junctions of pipes and

masonry with polymer mixed slurry.

sqm 95 522.90 49,676

10.2

22.700

Providing and laying integral cement based water

proofing treatment including preparation of surface as

required for treatment of roofs, balconies, terraces etc

consisting of following operations: a) Applying a slurry

coat of neat cement using 2.75 kg/sqm admixed with

water proofing compound conforming to IS : 2645 and

approved by Engineer-in-charge including laying glass

fibre cloth of approved quality in top layer of plaster

and finally finishing the surface with trowel with neat

cement slurry and making pattern of 300x300 mm

square 3 mm deep. e) The whole terrace so finished

shall be flooded with water for a minimum period of

two weeks for curing and for final test. All above

operations to be done in order and as directed and

specified by the Engineer-in-Charge :



SR.

NO.DSR 2014

ITEM NO.


10.3

22.170

Providing and laying in situr seven course water

proofing treatmen with APP (Atactic Polypropylene)

modified Polymeric membrane over roof consisiting of

first coat of bitument primer @0.40 kg per sq.mt, wnd,

4th and 6th courses of bonding material @1.20kg/sqm,

which shall consist of blown type bitumen of grade

85/25 conforming to IS:702, 3rd and 5th layers of

roofing membrance APP modified Polymeric

membrane 2.0 mm thick of 3.00 kg/sq.mt weight

consisting of five layers prefabricated with centre core

as 100 micron HMHDPE film sandwiched on both

sides with polymeric mix and the polymeric mix and

the polymeric mix is protected on both side with 20

micron HMHDPE film. 7th the top most layer shall be

finished with brick tiles of class designation 10 grouted

with cemen mortar 1:3 (1 cement:3 fine sand) mixed

with 2 per cent integral water proofing compound by

weight of cemen over a 12 mm layer of cemen mortar

1:3 (1 cement:3 fine sand) and finished neat (item of

laying brick tiles shall be papid for separately)

Sqm 230 572.25 131,618

SUB TOTAL 181,293

11.0 STEEL REINFORCEMENT

5.220

Steel reinforcement for R.C.C. work including

straightening, cutting, bending, placing in position and

binding all complete upto plinth level.

11.1 5.22.6 Thermo-Mechanically Treated bars Kg. 68.10 0

5.22A

Steel reinforcement for R.C.C. work including

straightening, cutting, bending, placing in position and

binding all complete above plinth level.

11.2 5.22A.6 Thermo-Mechanically Treated bars Kg. 72201 68.10 4,916,920

11.3 9.480 M.S. GRILL

Providing and fixing M.S. grills of required pattern in

frames of windows

etc. with M.S. flats, square or round bars etc. including

priming coat with

approved steel primer all complete.

Fixed to steel windows by welding Kg 1320 109.00 143,880

SUB TOTAL 5,060,800

CIVIL WORKS TOTAL 20,383,881



SR.

NO.DSR 2014

ITEM NO.


12.0 ELECTRICAL BOQs

LIGHT FIXTURES

12.1

SOR 2012-13.

(ITEM NO 5-1-

6)

Providing & erecting Approved make Power Saving 50 Watt

1200mm dia Ceiling Fan with double ball bearing ISI mark

with Condenser 230 volt A.C. 50 Hz 1200 mm sweep complete

having 3blades with aluminium blades with , canopy & 30 cms.

down rod erected with 24/ 0.2, 3 core flexible wire with

earthing.(Make shall be approved by Engineer in charge))

Nos 46 2070.00 95,220

12.2

SOR 2012-13.

(ITEM NO 5-2-

3)

Supplying & erecting fan hook box of 10 mm M.S. round bar

bounded to the RCC bars up to 50mm length each side and

pierced through a 16 Gauge M.S. box / Heavy Duty PVC box

complete erected concealed in Ceiling with necessary finishing.

Nos 46 125.00 5,750

12.3

SOR 2012-13.

(ITEM NO 5-2-

5)

Providing 2.5mm.thick laminated acrylic sheet to cover the fan

hook or Fan box.Nos 46 20.00 920

12.4

SOR 2012-13.

(ITEM NO 5-2-

1)

Supplying and erecting 19 / 20 mm. nominal bore Medium

Class M.S. Pipe down rod erected duly painted for fan complete

with necessary 24/ O.20, 3 core flexible wire with earthing.

Mtr 44 125.00 5,500

12.5

SOR 2012-13.

(ITEM NO.5-3-

4-A)

Supplying and erecting approved make exhaust fan having size

305mm, 900 RPM. CAT IINos 16 2400.00 38,400

12.6

SOR 2012-13.

(ITEM NO.5-3-

5)

Providing suitable M.S.louver shutter of the Exhaust Fan. Nos 16 430.00 6,880

12.7

SOR 2012-13.

(ITEM NO.5-3-

8)

Providing recess in window frame covering the rei-naining

portion of window frame with 15 mm thick plywood and

colour washing to match the colour of the wall.

Nos 16 200.00 3,200

155,870

13 INTERNAL WIRING

13.1

SOR 2012-13.

(ITEM NO 1-2-

1.)

Point wiring for Light / Bell with 2-1.5 sq.mm & earthwire of

1.5 sq.mm (Green) both are of ISI marked 1.1 KV grade FRLS

PVC insulated multistrand copper wires, in following type of

pipe to be erected concealed in/ on surface on wall/ceiling

complete with 6A Modular type switch / bell push &

accessories and earth continuity of following type, erected on

PVC / Metallic box, single mounting base frame covered with

textured/metallic front plate modules erected on / in wall /

ceiling as per pipe erected, with necessary Lamp holder/ceiling

rose / H.D.Connector as directed. (a) with medium class Rigid

PVC pipe and accessories. Cat. III

Pt. 182 420.00 76,440

13.2

SOR 2012-13.

(ITEM NO 1-1-

4.)

Point wiring for secondary light point with 2-1.5 sq.mm &

earthwire of 1.5 sq.mm (green) both are of ISI marked 1.1 KV

grade FRLS PVC insulated multistrand copper wires, in

following type of pipe to be erected concealed in / flushed on

wall/ceiling, complete with earth continuity and necessary

connection with primary light with accessories erected on

Metal / PVC box covered with 3 mm thick PC(Polycarbonet) /

Acrylic sheet for open / concealed wiring. with necessary

Lamp holder / ceiling rose / H.D.Connector as directed.(a) with

medium class Rigid PVC pipe and accessories

Pt. 78 100.00 7,800

13.3

SOR 2012-13.

(ITEM NO 1-2-

2.)

Point wiring for FAN with 2-1.5 sq.mm & earthwire of 1.5

sq.mm (Green) both are of .ISI marked 1.1 KV Grade FRLS PVC

insulated multistrand copper wires, in following type of pipe to

be erected concealed in / flushed on wall/ceiling complete

with 6A Modular type switch and hum free EME four or more

step type electronic fan regulator with separately mounted and

accessories with earth continuity of following type erected on

PVC / Metallic box, single mounting base frame covered with

textured/metallic front plate modules erected on / in wall /

ceiling as per pipe erected. with necessary ceiling rose /

H.D.Connector as directed. (a) with medium class Rigid PVC

pipe and accessories. Cat. III

Pt. 46 600.00 27,600

13.4

SOR 2012-13.

(ITEM NO 1-2-

4.)

Point wiring for Looped Plug with 6A Modular type switch & 5

pin socket erected on PVC / Metallic box, single mounting base

frame covered with textured / metallic front plate modules

erected on / in wall / ceiling with following type accessories.

Cat. III

Pt. 25 240.00 6,000

TOTAL FOR LIGHT FIXTURES



SR.

NO.DSR 2014

ITEM NO.


13.5

SOR 2012-13.

(ITEM NO 1-2-

6)

Providing following type of Modular Type Accessories

mounted with pvc / metallic box, single mounting base frame

covered with textured / metallic front plate , modules erected

with necessary connection. As desired by Engineer In charge

(1)One No. SP 6 Amp. (2) One No 5 pin plug

Nos 5 300.00 1,500

13.6

SOR 2012-13.

(ITEM NO 1-4-

1)

Mains with 1.1 KV grade FRLS PVC insulated ISI marked

stranded Copper conductor wire in following type of pipe to

be erected concealed in /flushed on wall/ceiling, with 1.5 sq.

mm copper conductor FRLS PVC insulated stranded wire of

green colour for earth continuity of following size (a) with

medium class Rigid PVC pipe and accessories. Cat. III (b) 2 wire

2.5 sq. mm

Rmt. 3000 80.00 240,000

13.7

SOR 2012-13.

(ITEM NO 1-2-

6)

Providing following type of Modular Type Accessories

mounted with pvc / metallic box, single mounting base frame

covered with textured / metallic front plate , modules erected

with necessary connection. As desired by Engineer In charge

(9) 16 Amp. SP one way switch (10) 6/16Amp. Universal

socket

Nos 24 380.00 9,120

13.8

SOR 2012-13.

(ITEM NO 1-4-

2)

Mains with 1.1 KV grade FRLS PVC insulated ISI marked

stranded Copper conductor wire in following type of pipe to be

erected in / on wall / ceiling with 2.5 sq. mm copper conductor

FRLS PVC insulated stranded wire of green colour for earth

continuity of following size (a) with medium class Rigid PVC

pipe and accessories (a) 2 wire 4 sq. mm

Rmt. 1200 110.00 132,000

500,460

14 COMPUTER WIRING

14.1

SOR 2012-13.

(ITEM NO 1-6-

2-B)

Providing & erecting Switch board for Computer or electric

apparatus consisting of following items in single board erected

on PVC / Metal board with 3 mm thick PC (Polycarbonate) /

Acrylic sheet erected as directed

1 no. 6A/16A universal plug-switch combined.

1 nos. 16A Switch

2 nos. 6A 5 pin Plug [B] For Modular Type Accessories CAT III

Nos 48 1140 54,720

54,720

15 DB's/FLOOR PANEL

Supply,Installation, testing and commissioning of Panel

Board as per IS , Technical Specifications & respective

drawings. The unit rate for each item shall include

Supply & delivery of the panels at the site. Shifting of

panels from site store to the suitable location.(If

applicable) Installation of panel in Electric room or

Location suggested by client within campus including

removing packing. Earthing all components, frame etc. to

a common internal earth bar. Supply & fixing all

accessories and supporting structure. Supply and fixing

of M.S. 100 mm. channels for fixing the panels

connection, testing & commissioning. The panels shall be

compatible to BMS whereever shown in the SLD.

Checking of Internal connection and wiring, operation of

switches, starter, MCCB, MCB, relays, contactors etc.

Supply of necessary tools, hardware, testing hardware,

testing equipment etc. Electrical contractor shall carry

out the insulation test at site & all the readings shall be

submitted in duplicate to the consultant or engineer-in-

charge.

TOTAL FOR INTERNAL WIRING

TOTAL FOR COMPUTER WIRING



SR.

NO.DSR 2014

ITEM NO.


15.1

SOR BASED

RATE

ANALYSIS-2

Supply, Installation, Testing & Commissioning of Ground

Floor Main LT Panel-2 as per Description Below.

Nos 1 117000.00 117,000

Incomer : 160A Four Pole MCCB, Thermal Magnetic

Release, S/C, E/F, O/C, 50Hz, 25KABusbar Size : 160A TPN Al., with Insulation Strip, 415V,

50Hz, 25KA Withstanding for 1 Sec

Outgoing :

1) 40/63A FP MCB, 10KA - 10 Nos C curve

2) 63A FP MCCB, 25KA - 2 Nos

15.2

SOR BASED

RATE

ANALYSIS-3

Supply, Installation, Testing & Commissioning of Utility

Panel as per Description Below.

EACH 1 54000.00 54,000

Incomer : 63A Four Pole MCCB, Thermal Magnetic

Release, 25KABusbar Size : 63A TPN Al. with Insulation Strip, 415V,

50Hz, 25KA Withstanding for 1 Sec

Outgoing :

1) 40A FP MCB, 10KA - 4 Nos C curve

2) 32A DP MCB, 10KA - 2 Nos B curve

15.3

SOR BASED

RATE

ANALYSIS-68 Way SS Double Door Three Phase DB

EACH 10 15000.00 150,000

Incomer : 40/63 A FP MCB. 10KA

ELCB : 3 nos of 32/40 A DP ELCB, 30 mA

Outgoing : 18 nos of 6/10/16/20A SP MCB, 10KA

15.4

SOR BASED

RATE

ANALYSIS-5

Supply, Installation, Testing & Commissioning of Single

Phase Distribution Box as per description below

,Specification, Technical Data sheet & IS.

EACH 1 5000.00 5,000

6 Way SS Single Door Type Distribution Box

Incomer : 40A DP ELMCB, 30 Ma

Outgoing : 6 nos of 6/10/16/20A SP MCB, 10KA

326,000

16 LT CABLES AND TERMINATIONS

16.1

SOR 2012-13.

(ITEM NO 4-3-

3-)

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured

cable multistrand Aluminium conductor for 1.1 KV. to be laid

on wall with necessary clamps or in existing trench / pipe of

following size of cables (E) 3 1/2 core 120 Sq. mm ( 70 Sq.

mm 1/2 core)

Mtr 100 660.00 66,000

16.2

SOR 2012-13.

(ITEM NO 4-3-

3-)




following size of cables (A) 3 1/2 core 25 Sq. mm ( 16 Sq. mm

1/2 core)

Mtr 15 220.00 3,300

16.3

SOR 2012-13.

(ITEM NO 4-3-

4-)




following size of cables (d) 4 core 16 Sq. mm

Mtr 80 180.00 14,400

16.4

SOR 2012-13.

(ITEM NO 4-6-

3)

Providing and, fixing heavy duty flange type brass cable gland

with rubber ring for PVC insulated armoured cable complete

with out going tails, insulating tape etc for following size of

cables.(E) 3.5 core 120 Sq. mm

Ea 2 150.00 300

16.5

SOR 2012-13.

(ITEM NO 4-6-

3)




cables.(A) 4 core 25 Sq. mm

Ea 2 70.00 140

16.6

SOR 2012-13.

(ITEM NO 4-6-

1)




cables.(E) 4 core 16 Sq. mm

Ea 4 50.00 200

16.7

SOR 2012-13.

(ITEM NO 4-7-

1)

Solderless crimping type Aluminium lugs conforming to IS

suitable for cable of following size evenly crimped with high

pressure tool & connected to switchgear terminals with

brass/cadmium plated nut bolts in an approved manner. (H)

120 Sq.mm.

Ea 8 45.00 360

TOTAL FOR DB'S



SR.

NO.DSR 2014

ITEM NO.


16.8

SOR 2012-13.

(ITEM NO 4-7-

1)




brass/cadmium plated nut bolts in an approved manner. (D)

25 Sq.mm.

Ea 8 15.00 120

16.9

SOR 2012-13.

(ITEM NO 4-7-

1)




brass/cadmium plated nut bolts in an approved manner. (C) 25

Sq.mm.

Ea 16 15.00 240

85,060

17 DATA CABLE

17.1

SOR 2012-13.

(ITEM NO 1-4-

8-C)

Supplying & erecting approved make LAN cable of following

size in existing pipe as per direction CAT - 6 CABLE with

Medium class RIGID PVC PIPES of following size complete to

be erected on/in wall or ceiling erected with necessary PVC

fittings & Junction boxes fixed with adhesive solution & Clamps

with following dia of pipes, in approved manner as directed 25

mm DIA CONDUIT

Rmt. 1200 50.00 60,000

17.2

SOR 2012-13.

(ITEM NO 1-3-

2-B)

Providing and erecting ISI mark Medium class RIGID PVC

PIPES of following size complete to be erected on/in wall or

ceiling erected with necessary PVC fittings & Junction boxes

fixed with adhesive solution & Clamps with following dia of

pipes, in approved manner as directed 25 mm DIA CONDUIT

Rmt. 1200 32.00 38,400

98,400

18 EARTHING

18.1

SOR 2012-13.

(ITEM NO. 3-

14-10-C)

Supplying & erecting in earthpit of minimum bore dia. 225mm

size ASH or approved make Safe Earthing Electrode consisting

Pipe-in-Pipe Technology as per IS 3043-1987 made of

corrosion free G.I.Pipes having Outer pipe dia of 80 mm

having 80-200 Micron galvanising, Inner pipe dia of 40 mm

having 200-250 Micron galvanising, connection terminal dia of

14 mm with constant ohmic value surrounded by highly

conductive compound with high charge dissipation suitable for

following type of applications. [C] For Electrical Installation

covering Transformer Neutrals, Lightning arrester Earthing,

A.C.Plant & Sensitive Computer System(like Automation,

SCADA)i.e. independent Earthing located in other than

normal soil i.e. Soft Rock, Marshy Soil etc..

-Length of Pipe : 3 Mtrs.

-Back filling Compound :2 nos Bags of 25 Kg.

NOS 2 16500.00 33,000

18.2

SOR 2012-13.

(ITEM NO. 3-

14-5)

Supply and laying of Earthing Conductor Providing and

erecting HOT Deep Galvanised Strip iron wire 8 to 16 S.W.G.KG 25 90.00 2,250

18.3

SOR 2012-13.

(ITEM NO. 3-

14-2)

Supply,laying and jointing of 25 X 6 MM GI Strip KG 30 90.00 2,700

37,950

SUB TOTAL-ELECTRICAL 1,258,460

19.0 Plumbing BOQs

COLD / HOT /DRINKING WATER SUPPLY:

INTERNAL/EXTERNAL WATER SUPPLY

WORK:- Providing,laying and jointing in true

line and level U.P.V.C pipe (SCH-40) of

following dia. Including fittings of standard make

as approved by engineer-in-charge. Pipe shall be

fixed on the wall with the help of clamp at every

2000 mm center to center or shall be concealed as

directed including necessary fittings etc. testing of

pipe and joints and fixing the same with adhesive

solvent, including cost of all materials.

a) 15 mm

Rmt 26 85.00 2,210

b) 25 mm Rmt 50 102.00 5,100

SOR

2013-14

Item No -

0.0

19.1

TOTAL FOR DATA CABLES

TOTAL FOR EARTHING

TOTAL FOR LT CABLES



SR.

NO.DSR 2014

ITEM NO.


c) 32 mm Rmt 16 135.00 2,160

d) 40 mm Rmt 24 169.00 4,056

E) 50 mm Rmt 0 217.00 0

Supplying & erecting resin bonded flap rock wool

/ glass wool with conductivity value 1.67 sq.mm

per watt & to with stand the temp. to 100 degree

centigrade C thickness 50mm with G I pipe of

following size dia "B" class as per IS:1239. The

plastic sheet to be used as covering of glass wool.

Al. cladiy besides other materials like chicken

mesh, 26 G Al. Sheet shall be used for cladding

the insulation pipe.

[A] 20 mm NB pipe

Rmt 0 360.00 0

[B] 25 mm NB pipe Rmt 20 440.00 8,800

[C] 32 mm NB pipe Rmt 0 530.00 0

[D] 40 mm NB pipe Rmt 0 620.00 0

19.3

SOR

2013-14

Item No -

00

Providing and Laying & Jointing in true line

level 110 diameter U.P.V.C (Type'B')

conforming to IS13592-1992 with one end plain

and other end socketed with rubber ring, and

fittings conforming to ISI 14735-1999 of

approved make for drinage system pipe line, pipe

shall be jointed with each other with rubber

lubricant,pipe shall be fixed on wall using of PVC

clamp of the size 110 mm diametre x210 mm

length x 196 mm height at every 2000 mm center

to center or shall be concealed in walls as directed

including testing of pipes and joints and jointed

with adhesive solvant cement including cost of all

materials.

(i) 110 mm Dia(DOWNTAKE FOR SOIL

WATER AND RAIN WATER)

Rmt 71 526.00 37,556

19.4

SOR

2013-14

Item No -

00


level 110 diameter U.P.V.C (Type'B')








length x 196 mm height at every 2000 mm center

to center or shall be concealed in walls as directed

including testing of pipes and joints and jointed

with adhesive solvant cement including cost of all

materials.

(iii) 160 mm Dia(DOWNTAKE FOR SOIL

WATER AND RAIN WATER)

Rmt 16 948.00 15,168

19.5Providing & fixing in position cowl vent to pipes

a) 75 mm dia

Each 5 431.00 2,155

19.5.1 100 mm dia Each 2 584.00 1,168

19.2

SOR

2013-14

Item No -

0.0

ELECTRIC

AL SOR

2012-13

ITEM NO.

8-11-8

SOR

2013-14

Item No -

19.1



SR.

NO.DSR 2014

ITEM NO.


19.6

SOR

2013-14

Item No -

23.87

Providing and fixing PVC SWR Nahni trap IS

14735 for drain - 100 mm diameter with jali of

the following nominal diameter of self cleansing

design with C.I. scread down or hinged grating

including the cost of cutting and making good the

walls

Each 43 453.00 19,479

19.7

SOR

2013-14

Item No -

23.112

Providing and fixing wash down water closet

(European type, WC pan) with integral S trap

including jointing the trap with soil pipe in cement

mortar 1:1 (1 Cement : 1 fine sand) ( Seal and

cover to be measured and paid for separately) A)

vitrious china white colour

(Cera-2008B / Parryware-C0287 / Hindware-

20011)

Each 17 1043.00 17,731

19.8P & F Flush Cock / Flush Valve (IS : 9758

Mark) for WC of approved quality make :

` CP brass push type 15mm nominal bore.

(-do-) 20mm nominal bore.

(-do-)exposed 25mm nominal bore.

(-do-) 32mm nominal bore.

(-do-) concealed 25mm nominal bore.

SOR

2013-14

Item No -

2.14.6

(-do-) concealed 32mm nominal bore. Each 17 1716.00 29,172

19.9

SOR

2013-14

Item No -

23.121

Providing and fixing plastic seat and cover for

wash down water closet with C.P. brass hinges

and rubber buffers A) Black plastic seat and cover

(Cera-2308 / Parryware-C8071 / Hindware-

20011)

Each 17 397.00 6,749

19.10

SOR

2013-14

Item No -

23.127

Providing and fixing wash basin with single hole

for pillar trap with CI or MS brackets painted

white including cutting holes and making good the

same but excluding fitting a) Vitreous

china flat back wash basin 550mm X 400mm size

in white colour

(Cera-1008/ Parryware-C0477 / Hindware-)

Each 12 1058.00 12,696

19.11

SOR

2013-14

Item No -

23.134

Providing and fixing rubber plug for sink or

wash basin.

Each 12 22.00 264

19.12

SOR

2013-14

Item No -

23.136

Providing and fixing M.I. fisher union for wash

basin or sink.

(A) 32 mm dia.

Each 12 103.00 1,236

19.13

SOR

2013-14

Item No -

23.143

Providing and fixing 600mmX450mm bevelled

edge mirror of superior glass mounted on 6mm

thick A.C. sheet or plywood sheet and fixing to

wooden plug with C.P. brass screws and washers.

Each 12 690.00 8,280



SR.

NO.DSR 2014

ITEM NO.


19.14

SOR

2013-14

Item No -

23.146

Providing and fixing toilet paper holder

(A) C.P. Brass

(Cera- / Parryware- / Hindware)

Each 17 456.00 7,752

19.15

SOR

2013-14

Item No -

23.122

Providing and Fixing Urinal of approved quality

including connecting the Urinal with waste pipe,

tap etc. completed.

[A] White earthenware flat back or corner type

size 430mmX 260mm X 350mm

(Cera-5001 / Parryware-C0501 / Hindware-

60005)

Each 0 783.00 0

19.16

SOR

2013-14

Item No -

0.0

Providing erecting and fixing double coated sintex

or equivalent PVC.(ISI) water tank of required

capacity each with all necessary fittings and

connection etc. complete on terrace.

Liter 5000 4.60 23,000

19.17

SOR

2013-14

Item No -

0.0

Providing and fixing ball cock of approved

quality as directed

(I)40 mm dia

Each 0 261.00 0

19.18

SOR

2013-14

Item No -

0.0


quality as directed

(II)32 mm dia

Each 8 261.00 2,088

19.19

SOR

2013-14

Item No -

0.0


quality as directed

(III)25 mm dia

Each 5 261.00 1,305


level Following diameter U.P.V.C (Type'B')








length x 196 mm height at every 2000 mm

center to center or shall be concealed in walls as

directed including testing of pipes and joints and

jointed with adhesive solvant cement including

cost of all materials.

(i) 110 mm dia.

Rmt 80 526.00 42,080

[ii] 160 mmDia. Rmt 50 948.00 47,400

Providing and laying Cement concrete 1:5:10 (1-

Cement : 5 - fine sand : 10-Graded stone

aggregate 40mm nominal size) bedding for

stoneware pipes of following internal diameters

with necessary formwork and curing complete.

[A] 100mm dia. (112 mm Ave. bed thickness)

Rmt 80 118.00 9,440

[B] 150mm dia. (166mm Ave. bed thickness)Rmt 50 199.00 9,950

19.22

SOR

2013-14

Item No -

24.19

Providing and fixing S.W. gully trap with C.I.

grating brick masonry chamber and water tight

C.I. cover with frame of 300mmX300mm size

(inside) with standard weight. I) Square mouth

traps.

a) 100mmX100mm size P type

Each 4 1432.00 5,728

19.20

19.21

SOR

2013-14

Item No -

0.0

SOR

2013-14

Item No -

24..2



SR.

NO.DSR 2014

ITEM NO.


Constructing Manhole with R.C.C. top slab in

1:2:4 mix (1-cement : 2-coarse send : 4-graded

stone aggregate 20mm nominal size) foundation

concrete 1:3:6 mix (1-cement : 3-coarse sand : 6-

Brick bats 40 + 50mm size) inside plastering

15mm thick with Cement a) With 230mm

thick walls of brick masonary using brick having

crushing strength not less than 35Kg. / Sq.cm. in

Cement Mortar 1:5 (1- Cement : 5- Coarse sand)

(I) Inside size 900mm X 1200mm and 1.5M. deep

including C.I. cover with frame size 560mm

diameter total weight of cover and frame to be not

less than 128 kgs. (Wt. of cover 64 kg. and Wt. of

frame 64 Kg.)

1) A type depth 0.90 Meter for 150 mm diameter

sewer.

Each 4 11609 46,436

2) B type depth 1.5 Meter for 150 mm diameter

sewer.

Each 1 20019.00 20,019

3) B type depth 2.24 Meter for 150 mm diameter

sewer.

Each 0 23518.00 0

Providing & Laying ( to level or Slope) and

jointing reinforced concrete Light Duty NoN

Pressure I.S. Class NP2 of the following internal

diameter with collars and butt ends prepared for

collar joints including testing of joints for

[B]250 mm dia

Rmt 10 414.00 4,140

[C]300 mm dia Rmt 0 523.00 0

19.24

ELECTRIC

AL SOR

2012-13

ITEM NO.

9-4-2 (F)

For 5 HP 3 phase open well horizontal mono

block pump set suitable for 150 LPM to 500

LPM @ 15 to 30 Mtr head. CAT-II (1W +1S)

with necessary valve fittings.

Each 1 54650.00 54,650

19.25

ELECTRIC

AL SOR

2012-13

ITEM NO.

9-5-6 (B)

Supplying and erecting approved make3 phase

motor control panel (ATS) made from 16 G.

CRCA sheet duly painted with epoxy power paint

inside and outside with hinged doors and locking

arrangement, consisting, of suitable switch of AC

23 duty with HRC fuses (Cat.III), starting and

running contactors, overload relay, Automatic

water level controller, Electronic timer with

master timer CT operated Ammeter with selector

switch, Voltmeter with selector switch, phase

indicating lamps, single phasing preventer , water

level guard, over load, start, run and stop push

buttons, air cooled auto transformer with 60%,

70%, 80% tapping, Panel to be erected on angle

iron frame grouted on wall as directed., contactors

relays, timer etc. shall be of L & T Siemens /

Cutler Hammer make.

(b) Suitable for 5 H.P.

Each 1 40250.00 40,250

19.22

19.23

SOR

2013-14

Item No -

24.27

SOR

2013-14

Item No -

24.22



SR.

NO.DSR 2014

ITEM NO.


19.26

ELECTRIC

AL SOR

2012-13

ITEM NO.

8-8-2

Providing & erecting water cooler having storage

capacity 150 Ltr. & cooling capacity 80 Ltr.per

hour @ an ambient temp of 45 deg C. The outlet

temp. of the water should drop by 15 deg C within

a hour, The water cooler should be comprising of

hermetically sealed compressor, fan motor,

condensing unit, water tank surrounded by

evaporating, coil, thermostats, relay etc.complete

with necessary inlet & outlet connection. The

body of water cooler will be made from Stainless

Steel.

Each 1 54000.00 54,000

19.27

ELECTRIC

AL SOR

2012-13

ITEM NO.

8-8-6

Supplying & erecting 5 stage single reverse

osmosis(R.O.) water purification system with

M.S. powder coated frame, prefilter housing with

'O' ring presediment filter GAC filter, carbon filter

suitable buster DC pump capacity 80 psi, mention

with 40 Osg inline type post carbon filter auto low

& high pressure switches with following size of

storage tank & LPH capacity & erected as directed

with one year comprehensive maintenance

guarantee.

[C] 50 Ltr / Hr with 250 psi 2 nos booster

pump

Each 1 27000.00 27,000

SUB TOTAL-PLUMBING 569,218


PART A


Summary NON DSR Works

1.0 Exposed Brick Work 1795500.00

2.0 Exposed Concrete Work 1489540.00

3.0 Flooring (Deleted) 0.00

4.0 Miscelleneous Work 570950.00

5.0 FURNITURE (Deleted) 0.00

6.0 Elevator 4,000,000

7.0 CCTV Works 75000

8.0 Plumbing Work 169,329

9.0 Electrical Work 483,350

TOTAL 8583669.00

PART-II-NON-DSR ITEMS FOR CIVIL WORK, ELECTRICAL, PLUMBING AND

SPECIALISED E&M WORKS

Signature of EPIL 20 Signature of Bidder


SR. NO. DESCRIPTION FURNITURE (Deleted)QTY RATE AMOUNT

1.0 EXPOSED BRICK WORK

1.1

Brick work with common burnt clay machine moulded modular bricks of

class designation 12.5 in exposed brick work including raking horizontal and

vertical grooves 10 mm wide 12 mm deep complete in cement mortar 1:6 (1

cement : 6 coarse sand) whilst the mortar is green in bond pattern as

specified. The mortar to be pressed with special steel trowels. The joints of

the pointed work shall be neat. The lines will be regular and uniform in

breadth and the joints shall be raised, flat, sunk or 'V' shaped as directed. No

false joints allowed.

sq.mts. 525 3300.00 1,732,500.00

1.2Waterproofing coating on brick cladding to prevent efflorescence (Dr.Fixit or

equivalent)

sq.mt 525 120.00 63,000.00

SUB TOTAL 1,795,500.00

2.0 EXPOSED CONCRETE WORK

FORMWORK

2.1Walls (any thickness) including attached pilasters, buttresses, plinth and string

courses etc.

Sqm 220 650.00 143,000.00

2.2 Suspended floors, roofs, landings, balconies and access platform. Sqm 1100 650.00 715,000.00

2.3 Lintels, beams, plinth beams, girders, bressumers and cantilevers. Sqm 750 650.00 487,500.00

2.4 Columns, Pillars, Piers, Piers, Abutments, Posts and Struts. Sqm 90 650.00 58,500.00

2.5 Stairs (excluding landings) except spiral stair-cases Sqm 60 650.00 38,740.00

2.6 Edges of slabs and breaks in floors and walls.

Below 20 cm wide rmt 360 130.00 46,800.00

SUB-TOTAL 1,489,540.00

3.0 FLOORING

Deleted

Total Flooring

Client : NATIONAL INSTITUTE OF DESIGN

Executing Agency: Engineering Projects India Ltd. (EPIL)

Architect: R T & ASSOCIATES PVT LTD.

Project Name: New Girls Hostel building, Ahmedabad

PART-II-BOQ FOR CIVIL WORK, ELECTRICAL, PLUMBING AND SPECIALISED E&M WORKS (NON-DSR ITEMS)




4.0 MISCELLENEOUS

MOSQUITO SCREEN FOR WINDOWS

Fixing sliding mosquito nets with aluminium section frames 2.5mm thick and

Saint Gobain or equivalent fiber net with roller mechanism for all windows

and ventilators

sqm 55 2250.00 123,750.00

4.1 Anodised aluminium fixed louvered screens for the duct shafts

Aluminum plain panels with finish of powder coating on the visible surface

of approved colour and supporting structure black colour spray painted

(Supersil or equivalent make)

sqm 100 2200.00 220,000.00

4.2 FLUSH DOORS (FOR TOILET)

30mm thick pine frame pine filler doors

PF bonded resin waterproof ISI brand with 1.00 mm thick super gloss

laminate on both sides and teak wood borders on the shutters on all four sides

60 2400 144,000.00

4.3Supplying and filling in plinth with river sand under floors, including

watering, ramming, consolidating and dressing complete.

cum 104 800.00 83,200

Total of Miscellenous 570,950.00

5.0 FURNITURE

Deleted

6.0 ELEVATORS

Machine room less 6 passenger elevator with 408 kg capacity and 1.00m/s

speed (Otis or equivalent)

2 2000000 4,000,000.00

7.0 CCTV

Supplying, testing, installation and commissioning of IP based CCTV system

for building security comprising of PTZ, fixed camera, cabling, recording,

display system and hardware and software support Including one Computer

at Reception

LS 75,000.00

8.0 PLUMBING WORK

8.1

Providing and Laying & Jointing in true line level 75 diameter

U.P.V.C (Type'B') conforming to IS13592-1992 with one end plain

and other end socketed with rubber ring, and fittings conforming to

ISI 14735-1999 of approved make for drinage system pipe line, pipe

shall be jointed with each other with rubber lubricant,pipe shall be

fixed on wall using of PVC clamp of the size 75 mm diametre x210

mm length x 196 mm height at every 2000 mm center to center or

shall be concealed in walls as directed including testing of pipes and

joints and jointed with adhesive solvant cement including cost of all

materials.

(i) 75 mm Dia(DOWNTAKE FOR SOIL WATER AND RAIN

WATER)

Rmt 149 350.00 52,150

8.2

Providing and fixing C.P Health Faucet with 1 meter flexible pipe

and wall hook approved make. The fixing include drilling &

installation of wooden plug with C.P. brass screw with making the

wall good with finishes as per instruction of Engg. In charge etc.

complete.

(Cera-CG205/ Parryware-T9937A1 / Hindware-F160027)

Each 17 435.00 7,395

8.3

Providing and fixing Angle Cock with screw, back nuts all necessary

fittings etc. Completed

(Cera-CM108/ Parryware-T9939A1 / Hindware-F100043)

Each 12 476.00 5,712

8.4

Providing and fixing 32 mm dia C.P. brass waste for wash basin or

sink.

(Cera- / Parryware-T9911A1 / Hindware-)

Each 12 180.00 2,160

8.5

Providing and fixing Chromium plated bottle trap with necessary

coupling of approved quality for wash basin.

(Cera-CM104 / Parryware-T3201A1 / Hindware-E850015)

Each 12 891.00 10,692

8.6

Supply installation testing and commisioning of HAND OPERATED

1.1 LITER CAPACITY soap dispenser, Push-Button type,

White/smoked. Cover in ABS Thermoplastic body.

(Cera-CA211 / Parryware-T3201A1 / Hindware)

Each 12 1285.00 15,420




8.7

Providing and fixing CP brass towel rail complete with C.P. brass

brackets fix to wooden plug with CP brass screws. I) 600 mm X 20

mm

(Cera-CA303 / Parryware-T6001A1 / Hindware-F880005)

Each 10 900.00 9,000

8.8

Providing and fixing of screwed down bib taps of following size

(A) Brass chromium plated screw down bib tap of 20mm

(Cera-CC103 / Parryware-T3504A1 / Hindware-F200003)

Each 53 608.00 32,224

8.9

Providing and fixing C.P. brass overhead shower with 15 mm or 20

mm inlet Arm

(A)100 mm dia.

(Cera-CH102,CG416A/Parryware-G0132A1,T9901A1/

Hindware-F160039)

Each 16 845.00 13,520

8.10

Providing and fixing concealed Stop cock for overhead shower

consisting of fitting sleeve, operating lever and adjustable wall flange

of approved quality and of 1/2" size as directed below

(Cera-CC127 / Parryware- / Hindware)

Each 16 860.00 13,760

8.11

Providing and fixing pillar tap capstan head screw down high

pressure with screw and back nuts of (I)15mm Dia.

(Cera-CC101 / Parryware-T3501A1 / Hindware-F200001)

Each 12 608.00 7,296

169,329

ELECTRICAL WORK

9.0 LIGHT FIXTURES

9.1

Supply, Installation, Assembling, Testing & Commissioning of 18W T-5 LED Wall/Surface

mounted complete with driver and LED suitable for 100w/Lumerns with all necessary

accessories to complete the installation Satisfactorily.

Nos 112 1300.00 145,600

9.2

Supply, Installation, Assembling, Testing & Commissioning of 9W LED Bracket light Wall

mounted complete with driver and LED suitable for 100w/Lumerns with all necessary

accessories to complete the installation Satisfactorily.

Nos 81 1050.00 85,050

9.3

Supply, Installation, Assembling, Testing & Commissioning of 14W LED Study (Mirror)

light Wall mounted complete with driver and LED suitable for 100w/Lumerns with all

necessary accessories to complete the installation Satisfactorily.

Nos 60 750.00 45,000

DATA CABLE

9.4

Supply and Installation of Layer 2/3 manageable switch, 24 x 10/100Mbps 802.3a/f PoE

ports, auto MDI/MDX, auto-sensing, supporting minimum 2 nos. 1000Mbps Copper or

ofc shared ports for uplinks.

Nos 2 22100.00 44,200

9.5Supplying,installtion,testing & commsissioning of 6U Network rack with base support. Each 1 5600.00 5,600

9.6

Supplying,installtion,testing & commsissioning of 2 Core OM3 Multimode Mode

Fiber Armoured cable complete with using Fusion splicing with pre-terminated

LC pigtails, dressing and proper fixing into rolosplice trays and coupler as

required complete with termination.

Rmt 100 170.00 17,000

9.7

Supply, Installation, testing & commisioning of Wire less WiFi Router with below

specification Networking Interface : (1) 10/100 Ethernet Port Buttons : Reset Antennas :

2 Integrated (Supports 2x2 MIMO with Spatial Diversity)Wi-Fi Standards : 802.11

b/g/n*Power Method : Passive Power over Ethernet (12-24V) Power Supply : Included

24V, 0.5A PoE Adapter Maximum Power Consumption : 6 W Maximum TX Power : 27

dBm BSSID : Up to Four Per Radio Power Save : Supported Wireless Security : WEP, WPA-

PSK, WPA-TKIP,WPA2 AES, 802.11i Certifications : CE, FCC, IC Mounting : Wall/Ceiling

(Kits Included) Operating Temperature : 10 to 70° C Operating Humidity : 5 - 80%

Condensing Supported :WMM, Voice, Video, Best Effort, and Background 'Concurrent

Clients 50+ Supported Data Rates (Mbps) Data Rates:802.11n, 6.5 Mbps to 300 Mbps

(MCS0 - MCS15, HT 20/40 802.11b, 1, 2, 5.5, 11 Mbps 802.11g, 6, 9, 12, 18, 24, 36, 48, 54

Mbps Frequency : 2.4 GHz WITH SOTWARE FOR CONTROL

Each 18 6500.00 117,000

External Routing Network

9.8Supply, Installation, Assembling, Testing & Commissioning of 200mm Dia RCC Hume Pipe

for External Cable LayingRmt 50 145.00 7,250

9.9Supply, Installation, Assembling, Testing & Commissioning of 100mm Dia RCC Hume Pipe

for External Cable LayingRmt 50 205.00 10,250

9.10

Supply, Installation, Assembling, Testing & Commissioning of 600mm x 600mm (Inner

Size)x 1000mm deep Electrical Manhole with External wall of 150mm Thick complete

with required accessories as per Structural Details

Each 4 1600.00 6,400

SUB TOTAL-ELECTRICAL 483,350

GRAND TOTAL-PART-II 8,583,669.00

SUB TOTAL PLUMBING-NON DSR WORKS


Date post:	10-Mar-2020
Category:	Documents
Upload:	others
View:	1 times
Download:	0 times

WORKS based on DSR -2014 CIVIL WORKS -...

Documents