+ All Categories
Home > Documents > WQ-iC Weld Fact Sheet[1] - Welding Inspection and ...

WQ-iC Weld Fact Sheet[1] - Welding Inspection and ...

Date post: 22-Oct-2021
Category:
Upload: others
View: 3 times
Download: 0 times
Share this document with a friend
2
Fact Sheet For more information, please contact us by e-mail at [email protected] or via our web page: wqic-eu.com. Welding Procedure & Welder Operator Approval Scheme for PED Permanent Joints DO YOU OR YOUR CUSTOMERS MANUFACTURE PRESSURE EQUIPMENT REQUIRING COMPLIANCE WITH THE PRESSURE EQUIPMENT DIRECTIVE? If you manufacture PED Category II, III & IV equipment using permanent joints, then you will need to comply with PED Annex 1 § 3.1.2. The welding procedures and welders including operators undertaking the work must be suitably qualified by a Notified Body or a Recognized Third-Party Organisation. For welders and operators this will require certification under a scheme accredited by an EU accreditation body to ISO/IEC 17024. How we can help WQ-iC is accredited by INAB (The Irish National Accreditation Board) to ISO/IEC 17024 for the Approval of permanent joining personnel for PED. Candidates seeking certification under this scheme will have undergone prior training and or have suitable industrial experience covered by the scheme. Where no permanent joining qualifications are held, the candidate will need to demonstrate evidence of utilising the relevant joining process in the 6 months preceding the application. The scheme is open to all seeking permanent joining qualifications under this scheme. Examples of qualification testing include: BS EN ISO 9606-1. Qualification testing of Welders –Steels BS EN ISO 9606-2. Qualification testing of Welders – Aluminium /Aluminium Alloys BS EN ISO 9606-3. Qualification testing of Welders – Copper and Copper Alloys BS EN ISO 9606-4. Qualification testing of Welders – Nickel and Nickel Alloys BS EN ISO 9606-5. Qualification testing of Welders – Titanium and Zirconium Alloys ASME - Boiler and Pressure Vessel Code. Section IX. Welding and brazing Qualifications The above list is not intended to be exhaustive and other appropriate standards may be used with agreement of WQ-iC Ltd.
Transcript

Fact Sheet

For more information, please contact us by e-mail at [email protected] or via our web page: wqic-eu.com.

Welding Procedure & Welder Operator Approval Scheme for PED Permanent Joints

DO YOU OR YOUR CUSTOMERS MANUFACTURE PRESSURE EQUIPMENT REQUIRING COMPLIANCE WITH THE PRESSURE EQUIPMENT DIRECTIVE?

If you manufacture PED Category II, III & IV equipment using permanent joints, then you will need to comply with PED Annex 1 § 3.1.2. The welding procedures and welders including operators undertaking the work must be suitably qualified by a Notified Body or a Recognized Third-Party Organisation. For welders and operators this will require certification under a scheme accredited by an EU accreditation body to ISO/IEC 17024.

How we can help

WQ-iC is accredited by INAB (The Irish National Accreditation Board) to ISO/IEC 17024 for the Approval of permanent joining personnel for PED. Candidates seeking certification under this scheme will have undergone prior training and or have suitable industrial experience covered by the scheme. Where no permanent joining qualifications are held, the candidate will need to demonstrate evidence of utilising the relevant joining process in the 6 months preceding the application. The scheme is open to all seeking permanent joining qualifications under this scheme. Examples of qualification testing include:

• BS EN ISO 9606-1. Qualification testing of Welders –Steels • BS EN ISO 9606-2. Qualification testing of Welders –

Aluminium /Aluminium Alloys • BS EN ISO 9606-3. Qualification testing of Welders – Copper

and Copper Alloys • BS EN ISO 9606-4. Qualification testing of Welders – Nickel

and Nickel Alloys • BS EN ISO 9606-5. Qualification testing of Welders – Titanium

and Zirconium Alloys • ASME - Boiler and Pressure Vessel Code. Section IX. Welding

and brazing Qualifications

The above list is not intended to be exhaustive and other appropriate standards may be used with agreement of WQ-iC Ltd.

Fact Sheet

For more information, please contact us by e-mail at [email protected] or via our web page: wqic-eu.com.


Recommended