WRT54GL-EU_11_UG_A-WEB

8/6/2019 WRT54GL-EU_11_UG_A-WEB

http://slidepdf.com/reader/full/wrt54gl-eu11uga-web 1/49

USER GUIDE

Wireless-G

Broadband Router

Model:WRT54GL (EU



Table of Contents

iWireless-G Broadband Router

Chapter 1: Product Overview 2

Front Panel 2

Back Panel 2

Chapter 2: Wireless Security Checklist 3

General Network Security Guidelines 3Additional Security Tips 3

Chapter 3: Advanced Confguration 4

Setup > Basic Setup 4

Setup > DDNS 7

Setup > MAC Address Clone 8

Setup > Advanced Routing 9

Wireless > Basic Wireless Settings 9

Wireless > Wireless Security 10

Wireless > Wireless MAC Filter 12Wireless > Advanced Wireless Settings 13

Security > Firewall 14

Security > VPN Passthrough 14

Access Restrictions > Internet Access 15

Applications and Gaming > Port Range Forward 16

Applications & Gaming > Port Triggering 16

Applications and Gaming > DMZ 17

Applications and Gaming > QoS 17

Administration > Management 18

Administration > Log 19

Administration > Diagnostics 19

Administration > Factory Deaults 19

Administration > Firmware Upgrade 20

Administration > Confg Management 20

Status > Router 20

Status > Local Network 21

Status > Wireless 21

Appendix A: Troubleshooting 22

Appendix B: Specifcations 23

Appendix C: Warranty Inormation 24

Limited Warranty 24

Appendix D: Regulatory Inormation 26

FCC Statement 26

Saety Notices 26

Industry Canada Statement 26

Avis d’Industrie Canada 26



Table of Contents

iiWireless-G Broadband Router

Wireless Disclaimer 27

Avis de non-responsabilité concernant les appareils sans fl 27

Declaration o Conormity with Regard to EU Directive 1999/5/EC (R&TTE Directive) 28

Wireless Equipment (Wireless-N/G/A/B Products) 29

CE Marking 29

National Restrictions 29Product Usage Restrictions 30

Technical Documents on wwwlinksyscom/international 30

User Inormation or Consumer Products Covered by EU Directive 2002/96/EC on WasteElectric and Electronic Equipment (WEEE) 31

Appendix E: Sotware License Agreement 35

Sotware in Linksys Products 35

Sotware Licenses 35



About This Guide

iWireless-G Broadband Router

About This Guide

Icon Descriptions

While reading through the User Guide you may see

various icons that call attention to speciic items Below isa description o these icons:

NOTE: This check mark indicates that there isa note o interest and is something that youshould pay special attention to while using theproduct

WARNING: This exclamation point indicatesthat there is a caution or warning and it issomething that could damage your property orproduct

WEB: This globe icon indicates a noteworthywebsite address or e-mail address

Online Resources

Website addresses in this document are listed withouthttp:// in ront o the address because most current webbrowsers do not require it I you use an older web browser,you may have to add http:// in ront o the web address

Resource Website

Linksys wwwlinksyscom

Linksys International wwwlinksyscom/international

Glossary wwwlinksyscom/glossary

Network Security wwwlinksyscom/security

Copyright and Trademarks

Linksys, Cisco and the Cisco Logo areregistered trademarks or trademarks o Cisco Systems, Inc and/or its ailiatesin the US and certain other countriesCopyright © 2008 Cisco Systems, Inc Allrights reserved Other brands and productnames are trademarks or registeredtrademarks o their respective holders



Chapter 1 Product Overview

2Wireless-G Broadband Router

Chapter 1:Product Overview

Thank you or choosing the Linksys Wireless-G BroadbandRouter The Router lets you access the Internet via a

wireless connection, broadcast at up to 54 Mbps, orthrough one o its our switched ports You can also usethe Router to share resources such as computers, printersand iles A variety o security eatures help to protectyour data and your privacy while online Security eaturesinclude WPA2 security, a Stateul Packet Inspection (SPI)irewall and NAT technology Coniguring the Router iseasy using the provided browser-based utility

Front Panel

SecureEasySetup (Orange/White) The Ciscologo is the Router’s SecureEasySetup button Itlights up and will stay orange when the Routeris powered on The color orange indicates thatthe Router is not using the SecureEasySetupeature, while the color white indicates that theRouter is using the SecureEasySetup eature

When the Router enters SecureEasySetupmode, the Cisco logo will turn white andstart lashing Ater the Router has generatedthe SSID and WPA Personal key, the Ciscologo will stop lashing and stay white

To clear the SSID and WPA Personal key, pressand hold down the Cisco logo or ive secondsThe Cisco logo will lash slowly as the Routerresets itsel The Cisco logo will turn orange toindicate a successul reset

NOTE:SecureEasySetup is a eature that makes

it easy to set up your wireless network I youhave SecureEasySetup devices, run the Router’sSetup Wizard CD-ROM and ollow the on-screen instructions to use SecureEasySetup

Power (Green) The Power LED lights upand will stay on while the Router is poweredon When the Router goes through its sel-diagnostic mode during every boot-up, thisLED will lash When the diagnostic is complete,the LED will be solidly lit

DMZ (Green) The DMZ LED indicates whenthe DMZ unction is being used This LED willremain lit as long as DMZ is enabled

WLAN (Green) The WLAN LED lights up whenthe wireless eature is enabled I the LED islashing, the Router is actively sending orreceiving data over the network

1, 2, 3, 4 (Green) These numbered LEDs,corresponding with the numbered ports on theRouter’s back panel, serve two purposes I theLED is continuously lit, the Router is successullyconnected to a device through that port A

lashing LED indicates network activity overthat port

Internet (Green) The Internet LED lights upwhen there is a connection made through theInternet port A lashing LED indicates network activity over the Internet port

Back Panel

Reset There are two ways to reset the Router’sactory deaults Either press and hold the ResetButton or approximately ive seconds, or restorethe deaults rom Administration > FactoryDeaults in the Router’s web-based utility

InternetThe Internet port is where you will

connect your cable or DSL Internet connection

1, 2, 3, 4 These Ethernet ports (1, 2, 3, 4) connectthe Router to PCs on your wired network andother Ethernet network devices

Power The Power port is where you willconnect the power adapter



Chapter 2 Wireless Security Checklist


Chapter 2:Wireless Security Checklist

Wireless networks are convenient and easy to install, sohomes with high-speed Internet access are adopting them

at a rapid pace Because wireless networking operates bysending inormation over radio waves, it can be morevulnerable to intruders than a traditional wired networkLike signals rom your cellular or cordless phones, signalsrom your wireless network can also be intercepted Sinceyou cannot physically prevent someone rom connectingto your wireless network, you need to take some additionalsteps to keep your network secure

1. Change the default wirelessnetwork name or SSID

Wireless devices have a deault wireless network nameor Service Set Identiier (SSID) set by the actory Thisis the name o your wireless network, and can be upto 32 characters in length Linksys wireless productsuse linksys as the deault wireless network name Youshould change the wireless network name to somethingunique to distinguish your wireless network rom otherwireless networks that may exist around you, but do notuse personal inormation (such as your Social Securitynumber) because this inormation may be available oranyone to see when browsing or wireless networks

2. Change the default password

For wireless products such as access points and routers,you will be asked or a password when you want to changetheir settings These devices have a deault password setby the actory The Linksys deault password is adminHackers know these deaults and may try to use themto access your wireless device and change your network settings To thwart any unauthorized changes, customizethe device’s password so it will be hard to guess

3. Enable MAC address filtering

Linksys routers give you the ability to enable Media AccessControl (MAC) address iltering The MAC address is aunique series o numbers and letters assigned to everynetworking device With MAC address iltering enabled,wireless network access is provided solely or wirelessdevices with speciic MAC addresses For example, you canspeciy the MAC address o each computer in your homeso that only those computers can access your wirelessnetwork

4. Enable encryption

Encryption protects data transmitted over a wirelessnetwork Wi-Fi Protected Access (WPA/WPA2) and WiredEquivalency Privacy (WEP) oer dierent levels o security

or wireless communication Currently, devices that areWi-Fi certiied are required to support WPA2, but are notrequired to support WEP

A network encrypted with WPA/WPA2 is more securethan a network encrypted with WEP, because WPA/WPA2uses dynamic key encryption To protect the inormationas it passes over the airwaves, you should enable thehighest level o encryption supported by your network equipment

WEP is an older encryption standard and may be theonly option available on some older devices that do not

support WPA

General Network Security Guidelines

Wireless network security is useless i the underlyingnetwork is not secure

Password protect all computers on the network and•

individually password protect sensitive iles

Change passwords on a regular basis•

Install anti-virus sotware and personal irewall•

sotware

Disable ile sharing (peer-to-peer) Some applications•

may open ile sharing without your consent and/orknowledge

Additional Security Tips

Keep wireless routers, access points, or gateways away•

rom exterior walls and windows

Turn wireless routers, access points, or gateways•

o when they are not being used (at night, duringvacations)

Use strong passphrases that are at least eight characters•

in length Combine letters and numbers to avoid usingstandard words that can be ound in the dictionary

WEB: For more inormation on wirelesssecurity, visit www.linksys.com/security



Chapter 3 Advanced Configuration


Chapter 3:Advanced Configuration

Ater setting up the Router with the Setup Wizard (locatedon the CD-ROM), the Router will be ready or use However,

i you’d like to change its advanced settings, use theRouter’s web-based utility This chapter describes eachweb page o the utility and each page’s key unctions Youcan access the utility via a web browser on a computerconnected to the Router

The web-based utility has these main tabs: Setup,Wireless, Security, Access Restrictions, Applications &Gaming, Administration, and Status Additional tabs willbe available ater you click one o the main tabs

NOTE: When irst installing the Router, youshould use the Setup Wizard on the Setup

CD-ROM I you want to conigure advancedsettings, use this chapter to learn about theweb-based utility

How to Access the Web-Based Utility

To access the web-based utility, launch the web browser onyour computer, and enter the Router’s deault IP address,192.168.1.1, in the Address ield Then, press Enter

A password request screen will appear (Non-Windows XPusers will see a similar screen) Leave the User name ield

blank The irst time you open the Web-based utility, usethe deault password admin (You can set a new passwordrom the Administration tab’s Management screen) Click OK to continue

Password Screen

Setup > Basic Setup

The irst screen that appears is the Basic Setup screen Thisallows you to change the Router’s general settings

Setup > Basic Setup

Internet Setup

The Internet Setup section conigures the Router to yourInternet connection Most o this inormation can beobtained through your ISP

Internet Connection Type

Select the type o Internet connection your ISP providesrom the drop-down menu The available types are:

Automatic Coniguration - DHCP•

Static IP•

PPPoE•

PPTP•

L2TP•

Telstra Cable•

Automatic Configuration - DHCP

By deault, the Router’s Internet Connection Type is set

to Automatic Configuration - DHCP, which should bekept only i your ISP supports DHCP or you are connectingthrough a dynamic IP address (This option usually appliesto cable connections)

Internet Connection Type > Automatic Coniguration - DHCP





Static IP

I you are required to use a permanent IP address toconnect to the Internet, select Static IP

Internet Connection Type > Static IP

Internet IP Address This is the Router’s IP address, whenseen rom the Internet Your ISP will provide you with theIP Address you need to speciy here

Subnet Mask This is the Router’s Subnet Mask, as seenby users on the Internet (including your ISP) Your ISP willprovide you with the Subnet Mask

Gateway Your ISP will provide you with the GatewayAddress, which is the ISP server’s IP address

DNS Your ISP will provide you with at least one DNS(Domain Name System) Server IP Address

PPPoE

Some DSL-based ISPs use PPPoE (Point-to-Point Protocolover Ethernet) to establish Internet connections I you areconnected to the Internet through a DSL line, check withyour ISP to see i they use PPPoE I they do, you will have

to enable PPPoE

Internet Connection Type > PPPoE

User Name and Password Enter the User Name andPassword provided by your ISP

Service Name I provided by your ISP, enter the ServiceName

Connect on Demand: Max Idle Time You can conigurethe Router to cut the Internet connection ater it has beeninactive or a speciied period o time (Max Idle Time) I your Internet connection has been terminated due toinactivity, Connect on Demand enables the Router toautomatically re-establish your connection as soon as youattempt to access the Internet again To use this option,select Connect on Demand In the Max Idle Time ield,enter the number o minutes you want to have elapsed

beore your Internet connection terminates The deaultMax Idle Time is 5 minutes

Keep Alive: Redial Period I you select this option,the Router will periodically check your Internetconnection I you are disconnected, then the Routerwill automatically re-establish your connection To use

this option, select Keep Alive In the Redial Period ield,you speciy how oten you want the Router to check the Internet connection The deault Redial Period is30 seconds

PPTP

Point-to-Point Tunneling Protocol (PPTP) is a service thatapplies to connections in Europe only

Internet Connection Type > PPTP

Internet IP Address This is the Router’s IP address, asseen rom the Internet Your ISP will provide you with theIP Address you need to speciy here

Subnet Mask This is the Router’s Subnet Mask, as seenby users on the Internet (including your ISP) Your ISP will

provide you with the Subnet MaskGateway Your ISP will provide you with the GatewayAddress


Connect on Demand: Max Idle Time You can conigurethe Router to cut the Internet connection ater it has beeninactive or a speciied period o time (Max Idle Time) I your Internet connection has been terminated due toinactivity, Connect on Demand enables the Router toautomatically re-establish your connection as soon as you

attempt to access the Internet again To use this option,select Connect on Demand In the Max Idle Time ield,enter the number o minutes you want to have elapsedbeore your Internet connection terminates The deaultMax Idle Time is 5 minutes

Keep Alive: Redial Period If you select this option, the

Router will periodically check your Internet connection If

you are disconnected, then the Router will automatically

re-establish your connection To use this option, selectKeep Alive In the Redial Period field, you specify how often

you want the Router to check the Internet connection The

default value is 30 seconds





L2TP

L2TP is a service that applies to connections in Israel only

Internet Connection Type > L2TP


L2TP Server This is the IP address o the L2TP ServerYour ISP will provide you with the IP Address you need tospeciy here

Connect on Demand: Max Idle Time You can conigure

the Router to cut the Internet connection ater it has beeninactive or a speciied period o time (Max Idle Time) I your Internet connection has been terminated due toinactivity, Connect on Demand enables the Router toautomatically re-establish your connection as soon as youattempt to access the Internet again To use this option,select Connect on Demand In the Max Idle Time ield,enter the number o minutes you want to have elapsedbeore your Internet connection terminates The deaultMax Idle Time is 5 minutes

Keep Alive: Redial Period I you select this option,the Router will periodically check your Internetconnection I you are disconnected, then the Routerwill automatically re-establish your connection To usethis option, select Keep Alive In the Redial Period ield,you speciy how oten you want the Router to check the Internet connection The deault Redial Period is30 seconds

Telstra Cable

Telstra Cable is a service that applies to connections inAustralia only

Internet Connection Type > Telstra Cable


Heart Beat Server This is the IP address o the HeartbeatServer Your ISP will provide you with the IP Address youneed to speciy here

Connect on Demand: Max Idle Time You can conigurethe Router to cut the Internet connection ater it has beeninactive or a speciied period o time (Max Idle Time) I your Internet connection has been terminated due toinactivity, Connect on Demand enables the Router toautomatically re-establish your connection as soon as you

attempt to access the Internet again To use this option,select Connect on Demand In the Max Idle Time ield,enter the number o minutes you want to have elapsedbeore your Internet connection terminates The deaultMax Idle Time is 5 minutes

Keep Alive: Redial Period I you select this option,the Router will periodically check your Internetconnection I you are disconnected, then the Routerwill automatically re-establish your connection To usethis option, select Keep Alive In the Redial Period ield,you speciy how oten you want the Router to check the Internet connection The deault Redial Period is30 seconds

Optional Settings

Some o these settings may be required by your ISP Veriywith your ISP beore making any changes

Optional Settings

Router Name In this ield, you can enter a name o up to39 characters to represent the Router

Host Name/Domain Name These ields allow you tosupply a host and domain name or the Router Some ISPs,usually cable ISPs, require these names as identiicationYou may have to check with your ISP to see i yourbroadband Internet service has been conigured with ahost and domain name In most cases, leaving these ieldsblank will work

MTU MTU is the Maximum Transmission Unit It speciiesthe largest packet size permitted or Internet transmission

Select Manual i you want to manually enter the largestpacket size that is transmitted To have the Router selectthe best MTU or your Internet connection, keep thedeault setting, Auto

Size When Manual is selected in the MTU ield, this optionis enabled Leave this value in the 1200 to 1500 range Thedeault size depends on the Internet Connection Type:

DHCP, Static IP, or Telstra:• 1500

PPPoE:• 1492

PPTP or L2TP:• 1460





Network Setup

The Network Setup section changes the settings on thenetwork connected to the Router’s Ethernet ports WirelessSetup is perormed through the Wireless tab

Router IP

This presents both the Router’s IP Address and SubnetMask as seen by your network

Router IP Address

Network Address Server Settings (DHCP)

The settings allow you to conigure the Router’s DynamicHost Coniguration Protocol (DHCP) server unction The

Router can be used as a DHCP server or your network ADHCP server automatically assigns an IP address to eachcomputer on your network I you choose to enable theRouter’s DHCP server option, make sure there is no otherDHCP server on your network

Network Address Server Settings (DHCP)

DHCP Server DHCP is enabled by actory deault I youalready have a DHCP server on your network, or you don’twant a DHCP server, then select Disable (no other DHCPeatures will be available)

Starting IP Address Enter a value or the DHCP server tostart with when issuing IP addresses Because the Router’s

default IP address is 19216811, the Starting IP Address must

be 19216812 or greater, but smaller than 1921681253

The default Starting IP Address is 192.168.1.100

Maximum Number of DHCP Users Enter the maximumnumber o PCs that you want the DHCP server to assignIP addresses to This number cannot be greater than 253The deault is 50

Client Lease Time The Client Lease Time is the amounto time a network user will be allowed connection to theRouter with their current dynamic IP address Enter theamount o time, in minutes, that the user will be “leased”this dynamic IP address Ater the time is up, the user willbe automatically assigned a new dynamic IP address Thedeault is 0 minutes, which means one day

Static DNS (1-3) The Domain Name System (DNS) is how

the Internet translates domain or website names into

Internet addresses or URLs Your ISP will provide you with at

least one DNS Server IP Address If you wish to use another,

enter that IP Address in one of these fields You can enter up

to three DNS Server IP Addresses here The Router will use

these for quicker access to functioning DNS serversWINS The Windows Internet Naming Service (WINS)manages each PC’s interaction with the Internet I youuse a WINS server, enter that server’s IP Address hereOtherwise, leave this blank

Time Setting

Select the time zone in which your network unctionsrom this drop-down menu (You can even automaticallyadjust or daylight saving time)

Time Setting

Click Save Settings to apply your changes, or click CancelChanges to cancel your changes

Setup > DDNS

The Router oers a Dynamic Domain Name System (DDNS)eature DDNS lets you assign a ixed host and domainname to a dynamic Internet IP address It is useul whenyou are hosting your own website, FTP server, or other

server behind the RouterBeore you can use this eature, you need to signup or DDNS service with a DDNS service provider,wwwdyndnsorg or wwwTZOcom I you do not want touse this eature, keep the deault setting, Disable

DDNS

DDNS Service

I your DDNS service is provided by DynDNSorg, thenselect DynDNS.org rom the drop-down menu I yourDDNS service is provided by TZO, then select TZO.com

The eatures available on the DDNS screen will vary,depending on which DDNS service provider you use





DynDNS.org

Setup > DDNS > DynDNS

System Select the DynDNS service you use: Dynamic,

Static, or Custom The deault selection is DynamicUser Name Enter the User Name or your DDNS account

Password Enter the Password or your DDNS account

Host Name The is the DDNS URL assigned by the DDNSservice

Mail Exchange (Optional) Enter the address o your mailexchange server, so e-mails to your DynDNS address go toyour mail server

Backup MX This eature allows the mail exchange serverto be a backup To disable this eature, keep the deault,No To enable the eature, select Yes I you are not sure

which setting to select, keep the deault, No

WildCard This setting enables or disables wildcardsor your host For example, i your DDNS address ismyplace.dyndns.org and you enable wildcards, then x.myplace.dyndns.org will work as well (x is the wildcard)To disable wildcards, keep the deault, Off To enablewildcards, select On I you are not sure which setting toselect, keep the deault, Off

Internet IP Address The Router’s Internet IP address isdisplayed here Because it is dynamic, it will change

Status The status o the DDNS service connection is

displayed hereClick Save Settings to apply your changes, or click CancelChanges to cancel your changes

TZO.com

Setup > DDNS > TZO

E-mail Address, Password, and Domain Name Enterthe settings o the account you set up with TZO

Internet IP Address The Router’s Internet IP address is

displayed here Because it is dynamic, it will changeStatus The status o the DDNS service connection isdisplayed here


Setup > MAC Address Clone

A MAC address is a 12-digit code assigned to a uniquepiece o hardware or identiication Some ISPs will requireyou to register a MAC address in order to access theInternet I you do not wish to re-register the MAC address

with your ISP, you may assign the MAC address you havecurrently registered with your ISP to the Router with theMAC Address Clone eature

Setup > MAC Address Clone

MAC Address Clone

Enable/Disable To have the MAC Address cloned, selectEnable

User Defined Entry Enter the MAC Address registeredwith your ISP here

Clone Your PC’s MAC Clicking this button will clone theMAC address o the computer you are using






Setup > Advanced Routing

This screen is used to set up the Router’s advancedunctions Operating Mode allows you to select thetype(s) o advanced unctions you use Dynamic Routingautomatically adjusts how packets travel on your networkStatic Routing sets up a ixed route to another network destination

Setup > Advanced Routing (Gateway)

Setup > Advanced Routing (Router)

Advanced Routing

Operating Mode Select the mode in which this Routerwill unction I this Router is hosting your network’sconnection to the Internet, select Gateway I anotherRouter exists on your network, select Router WhenRouter is chosen, Dynamic Routing will be available asan option

Dynamic Routing

RIP This eature enables the Router to automaticallyadjust to physical changes in the network’s layout and

exchange routing tables with the other router(s) TheRouter determines the network packets’ route based onthe ewest number o hops between the source and thedestination This eature is Disabled by deault From thedrop-down menu, you can also select LAN & Wireless,which perorms dynamic routing over your Ethernet and

wireless networks You can also select WAN (Internet),which perorms dynamic routing with data coming romthe Internet Selecting Both enables dynamic routing orboth networks, as well as data rom the Internet

Static Routing

Select set number To set up a static route betweenthe Router and another network, select a number romthe drop-down list (A static route is a pre-determinedpathway that network inormation must travel to reach aspeciic host or network) Enter the inormation describedbelow to set up a new static route (Click Delete This Entry to delete a static route)

Enter Route Name Enter a name or the Route here,using a maximum o 25 alphanumeric characters

Destination LAN IP The Destination LAN IP is the addresso the remote network or host to which you want to assigna static route

Subnet Mask The Subnet Mask determines whichportion o a Destination LAN IP address is the network portion, and which portion is the host portion

Default Gateway This is the IP address o the gatewaydevice that allows or contact between the Router and theremote network or host

Interface This interace tells you whether the DestinationIP Address is on the LAN & Wireless (Ethernet and wirelessnetworks) or the WAN (Internet)

Click Show Routing Table to view the Static Routes youhave already set up


Wireless > Basic Wireless Settings

The basic settings or wireless networking are set on this

screen





Wireless > Basic Wireless Settings

Wireless Network

Wireless Network Mode From this drop-down menu,you can select the wireless standards running on yournetwork I you have both 80211g and 80211b devicesin your network, keep the deault setting, Mixed I youhave only 80211g devices, select G-Only I you haveonly 80211b devices, select B-Only I you do not haveany 80211g and 80211b devices in your network, selectDisable

Wireless Network Name (SSID) The SSID is the network name shared among all points in a wireless networkThe SSID must be identical or all devices in the wirelessnetwork It is case-sensitive and must not exceed32 characters (use any o the characters on the keyboard)Make sure this setting is the same or all points in yourwireless network For added security, you should change

the deault SSID (linksys) to a unique name

Wireless Channel Select the appropriate channel romthe list provided to correspond with your network settingsAll devices in your wireless network must use the samechannel in order to communicate

Wireless SSID Broadcast When wireless clients surveythe local area or wireless networks to associate with, theywill detect the SSID broadcast by the Router To broadcastthe Router’s SSID, keep the deault setting, Enable I youdo not want to broadcast the Router’s SSID, then selectDisable

SecureEasySetup I you did not utilize this network connection eature during the Setup Wizard, you may useit here by clicking the green logo When you are promptedto start the push button setup, click OK

Reset Security Use this button to reset the securitysettings on your network You will need to runSecureEasySetup again on each device on your network to re-associate it with your network


Wireless > Wireless Security

The Wireless Security settings conigure the security o your wireless network There are six wireless securitymode options supported by the Router: WPA Personal,WPA Enterprise, WPA2 Personal, WPA2 Enterprise, RADIUS,

and WEP (WPA stands or Wi-Fi Protected Access, whichis a security standard stronger than WEP encryption WEPstands or Wired Equivalent Privacy, while RADIUS standsor Remote Authentication Dial-In User Service) Thesesix are briely discussed here For detailed instructionson coniguring wireless security or the Router, reer to“Chapter 2: Wireless Security”

Wireless Security

Security Mode

Select the security method or your wireless network I you do not want to use wireless security, keep the deault,Disabled

WPA Personal

NOTE: I you are using WPA, always rememberthat each device in your wireless network MUSTuse the same WPA method and shared key, orelse the network will not unction properly

Security Mode > WPA Personal

WPA Algorithm WPA supports two encryption methods,TKIP and AES, with dynamic encryption keys Select thetype o algorithm, TKIP or AES The deault is TKIP

WPA Shared Key Enter a WPA Shared Key o 8-63characters

Group Key Renewal Enter a Group Key Renewal period,which instructs the Router how oten it should change theencryption keys The deault Group Key Renewal period is3600 seconds

WPA Enterprise

This option eatures WPA used in coordination with aRADIUS server (This should only be used when a RADIUSserver is connected to the Router)





Security Mode > WPA Enterprise

WPA Algorithm WPA supports two encryption methods,TKIP and AES, with dynamic encryption keys Select thetype o algorithm, TKIP or AES The deault is TKIP

RADIUS Server Address Enter the IP Address o theRADIUS server

RADIUS Port Enter the port number o the RADIUSserver The deault value is 1812

Shared Key Enter the key shared between the Routerand the server

Key Renewal Timeout Enter a Key Renewal Timeoutperiod, which instructs the Router how oten it shouldchange the encryption keys The deault Key RenewalTimeout period is 3600 seconds

WPA2 Personal

Security Mode > WPA2 Personal

WPA Algorithm WPA2 supports two encryptionmethods, TKIP and AES, with dynamic encryption keys

Select the type o algorithm, AES, or TKIP + AES Thedeault selection is TKIP + AES

WPA Shared Key Enter a WPA Shared Key o 8-63characters

Group Key Renewal Enter a Group Key Renewal period,which instructs the Router how oten it should change theencryption keys The deault Group Key Renewal period is3600 seconds

WPA2 Enterprise

This option eatures WPA2 used in coordination with aRADIUS server (This should only be used when a RADIUSserver is connected to the Router)

Security Mode > WPA2 Enterprise

WPA Algorithm WPA2 supports two encryptionmethods, TKIP and AES, with dynamic encryption keysSelect the type o algorithm, AES, or TKIP + AES Thedeault selection is TKIP + AES




Key Renewal Timeout Enter a Key Renewal Timeout

period, which instructs the Router how oten it shouldchange the encryption keys The deault Key RenewalTimeout period is 3600 seconds

RADIUS

This option eatures WEP used in coordination with aRADIUS server (This should only be used when a RADIUSserver is connected to the Router)

Security Mode > RADIUS





IMPORTANT: If you are using WEP encryption,

always remember that each device in your

wireless network MUST use the same WEP

encryption method and encryption key, or else

your wireless network will not function properly




Default Transmit Key Select a Deault Transmit Key(choose which Key to use) The deault is 1

WEP Encryption Select a level o WEP encryption,64 bits 10 hex digits or 128 bits 26 hex digits Thedeault is 64 bits 10 hex digits

Passphrase Enter a Passphrase to automatically generateWEP keys Then click Generate

Key 1-4 I you did not enter a Passphrase, enter the WEPkey(s) manually

WEP

WEP is a basic encryption method, which is not as secureas WPA

Security Mode > WEP

Default Transmit Key Select a Deault Transmit Key

(choose which Key to use) The deault is 1

WEP Encryption Select a level o WEP encryption, 64 bits10 hex digits or 128 bits 26 hex digits The deault is64 bits 10 hex digits

Passphrase Enter a Passphrase to automatically generateWEP keys Then click Generate

Key 1-4 I you did not enter a Passphrase, enter the WEPkey(s) manually


Wireless > Wireless MAC Filter

Wireless access can be filtered by using the MAC addresses of

the wireless devices transmitting within your network’s radius

Wireless > Wireless MAC Filter

Wireless MAC Filter

Wireless MAC Filter To filter wireless users by MAC Address,either permitting or blocking access, click Enable If you do

not wish to filter users by MAC Address, keep the default

setting, Disable

Prevent Select this to block wireless access by MACAddress This button is selected by deault

Permit Only Select this to allow wireless access by MACAddress This button is not selected by deault

Edit MAC Filter List Click this to open the MAC Address

Filter List screen On this screen, you can list users, by MAC

Address, to whom you wish to provide or block access For

easy reference, click Wireless Client MAC List to display a listof network users by MAC Address

MAC Address Filter List






Wireless > Advanced Wireless Settings

This Wireless > Advanced Wireless Settings screen is usedto set up the Router’s advanced wireless unctions Thesesettings should only be adjusted by an expert administratoras incorrect settings can reduce wireless perormance

Wireless > Advanced Wireless Settings

Advanced Wireless

Authentication Type The deault is set to Auto, whichallows either Open System or Shared Key authenticationto be used With Open System authentication, the senderand the recipient do NOT use a WEP key or authenticationWith Shared Key authentication, the sender and recipientuse a WEP key or authentication

Basic Rate The Basic Rate setting is not actually one rate

o transmission but a series o rates at which the Routercan transmit The Router will advertise its Basic Rate to theother wireless devices in your network, so they know whichrates will be used The Router will also advertise that it willautomatically select the best rate or transmission Thedeault setting is Default, when the Router can transmitat all standard wireless rates (1-2Mbps, 55Mbps, 11Mbps,18Mbps, and 24Mbps) Other options are 1-2Mbps, oruse with older wireless technology, and All, when theRouter can transmit at all wireless rates The Basic Rateis not the actual rate o data transmission I you want tospeciy the Router’s rate o data transmission, conigurethe Transmission Rate setting

Transmission Rate The rate o data transmission shouldbe set depending on the speed o your wireless networkYou can select rom a range o transmission speeds, or youcan select Auto to have the Router automatically use theastest possible data rate and enable the Auto-Fallback eature Auto-Fallback will negotiate the best possibleconnection speed between the Router and a wirelessclient The deault value is Auto

CTS Protection Mode CTS (Clear-To-Send) ProtectionMode should remain disabled unless you are having severeproblems with your Wireless-G products not being able

to transmit to the Router in an environment with heavy80211b traic This unction boosts the Router’s abilityto catch all Wireless-G transmissions but will severelydecrease perormance

Frame Burst Enabling this option should provide yournetwork with greater perormance, depending on the

manuacturer o your wireless products To turn on theFrame Burst option, select Enable The deault is Disable

Beacon Interval The deault value is 100 Enter a valuebetween 1 and 65,535 milliseconds The Beacon Intervalvalue indicates the requency interval o the beacon Abeacon is a packet broadcast by the Router to synchronizethe wireless network

DTIM Interval This value, between 1 and 255, indicatesthe interval o the Delivery Traic Indication Message(DTIM) A DTIM ield is a countdown ield inormingclients o the next window or listening to broadcastand multicast messages When the Router has buered

broadcast or multicast messages or associated clients, itsends the next DTIM with a DTIM Interval value Its clientshear the beacons and awaken to receive the broadcastand multicast messages The deault value is 1

Fragmentation Threshold This value speciies themaximum size or a packet beore data is ragmentedinto multiple packets I you experience a high packeterror rate, you may slightly increase the FragmentationThreshold Setting the Fragmentation Threshold too lowmay result in poor network perormance Only minorreduction o the deault value is recommended In mostcases, it should remain at its deault value o 2346

RTS Threshold Should you encounter inconsistent datalow, only minor reduction o the deault value, 2347, isrecommended I a network packet is smaller than thepreset RTS threshold size, the RTS/CTS mechanism willnot be enabled The Router sends Request to Send (RTS)rames to a particular receiving station and negotiatesthe sending o a data rame Ater receiving an RTS, thewireless station responds with a Clear to Send (CTS) rameto acknowledge the right to begin transmission The RTSThreshold value should remain at its deault value o 2347

AP Isolation This isolates all wireless clients and wireless

devices on your network rom each other Wireless deviceswill be able to communicate with the Router but not witheach other To use this unction, select On AP Isolation isturned Off by deault

SecureEasySetup This eature allows you to enable ordisable the SecureEasySetup eature Select Disabled todisable the eature and turn o the button’s light Theeature is Enabled by deault






Security > Firewall

The Security > Firewall screen is used to conigure a irewallthat can ilter out various types o unwanted traic on theRouter’s local network

Security > Firewall

Firewall

Firewall Protection To use irewall protection, keep thedeault selection, Enable To turn o irewall protection,select Disable

Block WAN Requests

Block Anonymous Internet Requests This eaturemakes it more diicult or outside users to work theirway into your network This eature is selected by deaultDeselect the eature to allow anonymous Internetrequests

Filter Multicast Multicasting allows or multiple

transmissions to speciic recipients at the same time I multicasting is permitted, then the Router will allow IPmulticast packets to be orwarded to the appropriatecomputers This eature is selected by deault Deselectthis eature to disable it

Filter Internet NAT Redirection This eature usesport orwarding to block access to local servers romlocal networked computers Select Filter Internet NATRedirection to ilter Internet NAT redirection This eatureis not selected by deault

Filter IDENT (Port 113) This eature keeps port 113 rombeing scanned by devices outside o your local network

This eature is selected by deault Deselect this eature todisable it


Security > VPN Passthrough

The Security > VPN Passthrough screen allows you to enable

VPN tunnels using IPSec, PPTP, or L2TP protocols to pass

through the Router’s firewall

Security > VPN Passthrough

VPN Passthrough

IPSec Passthrough Internet Protocol Security (IPSec) isa suite o protocols used to implement secure exchangeo packets at the IP layer To allow IPSec tunnels to passthrough the Router, keep the deault, Enable

PPTP Passthrough Point-to-Point Tunneling Protocol(PPTP) allows the Point-to-Point Protocol (PPP) to betunneled through an IP network To allow PPTP tunnels topass through the Router, keep the deault, Enable

L2TP Passthrough Layer 2 Tunneling Protocol is themethod used to enable Point-to-Point sessions via theInternet on the Layer 2 level To allow L2TP tunnels to passthrough the Router, keep the deault, Enable






Access Restrictions > Internet Access

The Access Restrictions > Internet Access screen allows youto block or allow speciic kinds o Internet usage andtraic, such as Internet access, designated services, andwebsites during speciic days and times

Access Restrictions > Internet Access

Internet Access

Internet Access Policy Access can be managed by apolicy Use the settings on this screen to establish anaccess policy (ater Save Settings is clicked) Selecting apolicy rom the drop-down menu will display that policy’ssettings To delete a policy, select that policy’s numberand click Delete To view all the policies, click Summary(Policies can be deleted rom the Summary screen byselecting the policy or policies and clicking Delete Toreturn to the Internet Access tab, click Close)

Internet Policy Summary

Status Policies are disabled by deault To enable a policy,select the policy number rom the drop-down menu, andselect Enable

To create an Internet Access policy:

Select a number rom the1 Internet Access Policy drop-down menu

To enable this policy, select2 Enable

Enter a Policy Name in the ield provided3

Click 4 Edit List of PCs to select which PCs will be affected

by the policy The List of PCs screen appears You can

select a PC by MAC Address or IP Address You can also

enter a range of IP Addresses if you want this policy

to affect a group of PCs After making your changes,click Save Settings to apply your changes or Cancel

Changes to cancel your changes Then click Close

List o PCs

Select the appropriate option,5 Deny or Allow,depending on whether you want to block or allowInternet access or the PCs you listed on the List of PCs screen

Decide which days and what times you want this policy6to be enorced Select the individual days during whichthe policy will be in eect, or select Everyday Thenenter a range o hours and minutes during which thepolicy will be in eect, or select 24 Hours

Select any Blocked Services or Website Blocking you7wish to use

Click 8 Save Settings to save the policy’s settings, orclick Cancel Changes to cancel the policy’s settings

Blocked Services

You can ilter access to various services accessed over theInternet, such as FTP or telnet, by selecting services romthe drop-down menus next to Blocked Services (You canblock up to 20 services) Then enter the range o ports youwant to ilter

I the service you want to block is not listed or you want toedit a service’s settings, then click Add/Edit Service Thenthe Port Services screen will appear

Port Services





To add a service, enter the service’s name in the Service

Name ield Select its protocol rom the Protocol drop-down menu, and enter its range in the Port Range ieldsThen click Add

To modiy a service, select it rom the list on the rightChange its name, protocol setting, or port range Then

click ModifyTo delete a service, select it rom the list on the right Thenclick Delete

When you are inished making changes on the Port

Services screen, click Apply to save the changes I youwant to cancel your changes, click Cancel To close thePort Services screen and return to the Access Restrictions screen, click Close

Website Blocking by URL Address

I you want to block websites with speciic URL addresses,

enter each URL in a separate ield next to Website Blockingby URL Address

Website Blocking by Keyword

I you want to block websites using speciic keywords,enter each keyword in a separate ield next to Website

Blocking by Keyword


Applications and Gaming > Port Range

Forward The Applications & Gaming > Port Range Forward screen

allows you to set up public services on your network, such as

web servers, ftp servers, e-mail servers, or other specialized

Internet applications (Specialized Internet applications are

any applications that use Internet access to perform functions

such as videoconferencing or online gaming Some Internet

applications may not require any forwarding)

Applications and Gaming > Port Range Forward

Port Range Forward

To orward a port, enter the inormation on each line orthe criteria required

Application In this ield, enter the name you wish to givethe application Each name can be up to 12 characters

Start/End This is the port range Enter the number thatstarts the port range in the Start column and the numberthat ends the range in the End column

Protocol Select the protocol used or this application,either TCP or UDP, or Both

IP Address For each application, enter the IP Address o the PC running the speciic application

Enable Select Enable to enable port orwarding or therelevant application


Applications & Gaming > Port Triggering

The Applications & Gaming > Port Triggering screen allowsthe Router to watch outgoing data or speciic portnumbers The IP address o the computer that sends thematching data is remembered by the Router, so that whenthe requested data returns through the Router, the data ispulled back to the proper computer by way o IP addressand port mapping rules

Applications and Gaming > Port Triggering

Port Triggering

Application Enter the application name o the trigger

Triggered Range

For each application, list the triggered port number rangeCheck with the Internet application documentation orthe port number(s) needed





Start Port Enter the starting port number o the TriggeredRange

End Port Enter the ending port number o the TriggeredRange

Forwarded Range

For each application, list the orwarded port numberrange Check with the Internet application documentationor the port number(s) needed

Start Port Enter the starting port number o theForwarded Range

End Port Enter the ending port number o the ForwardedRange

Enable Select Enable to enable port triggering or theapplicable application

Click Save Settings to apply your changes, or click Cancel

Changesto cancel your changes

Applications and Gaming > DMZ

The DMZ eature allows one network computer to beexposed to the Internet or use o a special-purposeservice such as Internet gaming or videoconerencingDMZ hosting orwards all the ports at the same time toone PC The Port Range Forward eature is more securebecause it only opens the ports you want to have opened,while DMZ hosting opens all the ports o one computer,exposing the computer to the Internet

Applications and Gaming > DMZ

DMZ

Any PC whose port is being orwarded must have its DHCP

client unction disabled and should have a new static IPaddress assigned to it because its IP address may changewhen using the DHCP unction

To expose one PC, select Enable Then, enter thecomputer’s IP address in the DMZ Host IP Address ield Thiseature is disabled by deault


Applications and Gaming > QoS

Quality o Service (QoS) ensures better service tohigh-priority types o network traic, which mayinvolve demanding, real-time applications, such asvideoconerencing

There are three types o QoS available: Device Priority,Ethernet Port Priority, and Application Priority

Wired QoS

Enable/Disable To enable QoS, select Enable Otherwise,select Disable QoS is disabled by deault

Upstream Bandwidth Select Auto or Manual romthe drop-down menu Manual allows you to speciy themaximum outgoing bandwidth that applications canutilize

Applications and Gaming > QoS

Device Priority

Enter the name o your network device in the Device name

ield, enter its MAC Address, and then select its priorityrom the drop-down menu

Ethernet Port Priority

Ethernet Port Priority QoS allows you to prioritizeperormance or the Router’s our ports, LAN Ports 1-4 Foreach port, select the priority and low control setting





Priority Select High or Low in the Priority column TheRouter’s our ports have been assigned low priority bydeault

Flow Control I you want the Router to control thetransmission o data between network devices, selectEnabled To disable this eature, select Disabled Ethernet

Port Priority QoS does not require support rom your ISPbecause the prioritized ports LAN ports 1-4 are in yournetwork This eature is enabled by deault

Application Priority

Application Priority QoS manages inormation as it istransmitted and received Depending on the settings o the QoS screen, this eature will assign inormation a highor low priority or the applications that you speciy

Optimize Gaming Applications Select this toautomatically allow common game application portsto have a higher priority These games include, but are

not limited to: Counter-Strike , Half-Life, Age of Empires,Everquest , Quake2 /Quake3, and Diablo II The deaultsetting is unselected

Application Name Enter the name you wish to give theapplication in the Application Name ield

Priority Select High or Low to assign priority to theapplication The deault selection is Low

Specific Port # Enter the port number or theapplication

Wireless QoS

WMM Support Wi-Fi Multimedia (WMM), ormerlyknown as Wireless Multimedia Extensions (WME), isa Wi-Fi Alliance certiied eature, based on the IEEE80211e standard This eature provides QoS to wirelessnetworks It is especially suitable or voice, music andvideo applications; or example, Voice over IP ( VoIP), videostreaming, and interactive gaming I you have otherdevices on your wireless network that support WMM,select Enabled Otherwise, keep the deault, Disabled

No Acknowledgement This eature prevents the Routerrom re-sending data i an error occurs To use this eature,select Enabled Otherwise, keep the deault setting,

Disabled


Administration > Management

The Administration > Management screen allows thenetwork’s administrator to manage speciic Routerunctions or access and security

Administration > Management

Router Password

Local Router Access

Router Password Enter a new Password or the Router

Re-enter to confirm Enter the Password again to confirm

Web Access

Access Server HTTP (HyperText Transport Protocol) isthe communications protocol used to connect to serverson the World Wide Web HTTPS uses SSL (Secured SocketLayer) to encrypt data transmitted or higher securitySelect HTTP or HTTPS. The deault selection is HTTP

Wireless Access Web I you are using the Router ina public domain where you are giving wireless accessto your guests, you can disable wireless access to theRouter’s web-based utility You will only be able to accessthe web-based utility via a wired connection i you disablethe setting Keep the deault, Enable, to enable wirelessaccess to the Router’s web-based utility, or select Disable to disable wireless access to the utility

Remote Router Access

Remote Management To access the Router remotely,rom outside the network, select Enable

Management Port Enter the port number that will beopen to outside access You will need to enter the Router’spassword when accessing the Router this way, as usual

Use https To require the use o HTTPS or remote access,select this eature

UPnP

UPnP Keep the deault, Enable to enable the UPnPeature; otherwise, select Disable






Administration > Log

The Router can keep logs o all traic or your Internetconnection

Administration > Log

Log

Log To disable the Log unction, keep the deault setting,

Disable To monitor traic between the network and theInternet, select Enable

When you wish to view the logs, click Incoming Log orOutgoing Log, depending on which you wish to view


Administration > Diagnostics

The diagnostic tests (Ping and Traceroute) allow you tocheck the connections o your network components

Administration > Diagnostics

Ping Test

Ping The Ping test checks the status o a connectionClick Ping to open the Ping Test screen Enter the addresso the PC whose connection you wish to test and howmany times you wish to test it Then, click Ping The Ping

Test screen will show i the test was successul To stop thetest, click Stop Click Clear Log to clear the screen Click Close to return to the Diagnostics screen

The Ping Test

Traceroute Test

Traceroute To test the perormance o a connection,click Traceroute to open the Traceroute Test screen Enterthe address o the PC whose connection you wish to testand click Traceroute The Traceroute Test screen will show

i the test was successul To stop the test, click Stop Click Clear Log to clear the screen Click Close to return to theDiagnostics screen

The Traceroute Test

Administration > Factory Deaults

The Administration > Factory Defaults screen allows youto restore the Router’s coniguration to its actory deaultsettings

Factory Deaults

Restore Factory Defaults To reset the Router’s settingsto the deault values, select Yes, and then click SaveSettings Any settings you have saved will be lost whenthe deault settings are restored






Administration > Firmware Upgrade

The Administration > Firmware Upgrade screen allows you

to upgrade the Router’s firmware Do not upgrade the

firmware unless you are experiencing problems with the

Router or the new firmware has a feature you want to use

Administration > Firmware Upgrade

Beore upgrading the irmware, download the Router’sirmware upgrade ile rom the Linksys website, wwwlinksyscom Then extract the ile

Upgrade Firmware

Please select a file to upgrade Click Browse and selectthe extracted irmware upgrade ile Then click Upgrade

and follow the on-screen instructions

Administration > Conig Management

This screen is used to back up or restore the Router’s

coniguration ile

Administration > Conig Management

Backup Coniguration

To back up the Router’s coniguration ile, click BackupThen ollow the on-screen instructions

Restore Coniguration

Please select a file to restore Click Browse and selectthe coniguration ile Then click Restore

Status > Router

The Status > Router screen displays the Router’s currentstatus


Router Inormation

Firmware Version This is the Router’s current irmware

Current Time This shows the time, as you set on theSetup tab

MAC Address This is the Router’s MAC Address, as seenby your ISP

Router Name This is the speciic name or the Router,which you set on the Setup tab

Host Name I required by your ISP, this would have beenentered on the Setup tab

Domain Name I required by your ISP, this would havebeen entered on the Setup tab

Internet

Configuration Type

This section shows the current network inormationstored in the Router The inormation varies depending onthe Internet connection type selected on the Setup > Basic

Setup screen

Click Refresh to update the on-screen inormation





Status > Local Network

The Status > Local Network screen displays the status o your network

Status > Local Network

Local NetworkMAC Address This is the Router’s MAC Address, as seenon your local, Ethernet network

IP Address This shows the Router’s IP Address, as itappears on your local, Ethernet network

Subnet Mask This shows the current subnet mask beingconigured or your local network

DHCP Server I you are using the Router as a DHCP server,that will be displayed here

Start IP Address For the range o IP Addresses used by

devices on your local, Ethernet network, the beginning o that range is shown here

End IP Address For the range o IP Addresses used bydevices on your local, Ethernet network, the end o thatrange is shown here

DHCP Clients Table Clicking this button will open ascreen to show you which PCs are utilizing the Router as aDHCP server You can delete PCs rom that list, and severtheir connections, by checking a Delete box and clickingthe Delete button

DHCP Clients Table


Status > Wireless

The Status > Wireless screen displays the status o yourwireless network

Status > Wireless

Wireless

MAC Address This is the Router’s MAC Address, as seenon your local, wireless network

Mode As selected rom the Wireless > Basic Wireless

Settings screen, this displays the wireless mode (Mixed, G-Only, or Disabled) used by the network

SSID As entered on the Wireless > Basic Wireless Settings screen, this displays the wireless network name or SSID

DHCP Server The status o the DHCP server unction isdisplayed here

Channel As entered on the Wireless > Basic Wireless

Settings screen, this displays the channel on which your

wireless network is broadcasting

Encryption Function As selected on the Wireless >

Wireless Security screen, this displays the status o theRouter’s wireless security




Appendix A Troubleshooting


Appendix A:Troubleshooting

Your computer cannot connect to the Internet.

Follow these instructions until your computer can connectto the Internet:

Make sure that the Router is powered on The Power•

LED should be green and not lashing

I the Power LED is lashing, then power o all o •

your network devices, including the modem, Router,and computers Then power on each device in theollowing order:

Cable or DSL modem1

Router2

Computer3Check the cable connections The computer should•

be connected to one o the ports numbered 1-4 onthe Router, and the modem must be connected to theInternet port on the Router

The modem does not have an Ethernet port.

The modem is a dial-up modem or traditional dial-upservice To use the Router, you need a cable/DSL modemand high-speed Internet connection

You cannot use the DSL service to connect manually to

the Internet.

Ater you have installed the Router, it will automaticallyconnect to your Internet Service Provider (ISP), so you nolonger need to connect manually

The DSL telephone line does not ft into the Router’s

Internet port.

The Router does not replace your modem You still needyour DSL modem in order to use the Router Connectthe telephone line to the DSL modem, insert the setupCD into your computer, and then ollow the on-screeninstructions

When you double-click the web browser, you are

prompted or a username and password. I you want to

get rid o the prompt, ollow these instructions.

Launch the web browser and perorm the ollowing steps(these steps are speciic to Internet Explorer but are similaror other browsers):

Select1 Tools > Internet Options

Click the2 Connections tab

Select3 Never dial a connection

Click 4 OK

The Router does not have a coaxial port or the cable

connection.

The Router does not replace your modem You still needyour cable modem in order to use the Router Connect yourcable connection to the cable modem, insert the setup

CD into your computer, and then ollow the on-screeninstructions

The computer cannot connect wirelessly to the network.

Make sure the wireless network name or SSID is the sameon both the computer and the Router I you have enabledwireless security, then make sure the same securitymethod and key are used by both the computer and theRouter

You need to modiy the settings on the Router.

Open the web browser (or example, Internet Explorer or

Fireox), and enter the Router’s IP address in the addressield (the deault IP address is 192.168.1.1) Whenprompted, leave the User name ield blank and enter thepassword to the Router (the deault is admin) Click theappropriate tab to change the settings

WEB: I your questions are not addressed here,reer to the Linksys website, www.linksys.com



Appendix B Specifications


Appendix B:Specifications

Model WRT54GL

Standards IEEE 8023, IEEE 8023u,IEEE 80211g, IEEE 80211b

Channels 11 Channels (US, Canada)13 Channels (Europe, Japan)

Ports Internet: One 10/100 RJ-45 PortLAN: Four 10/100 RJ-45 SwitchedPortsOne Power Port

Button Reset, SecureEasySetup

Cabling Type CAT5

LEDs Power, DMZ, WLAN, LAN (1-4),Internet, SecureEasySetup

RF Power Output 18 dBm

UPnP able/cert Able

Security Features Stateul Packet Inspection (SPI)Firewall, Internet Policy

Wireless Security Wi-Fi Protected Access™2 (WPA2),WEP, Wireless MAC Filtering

Environmental

Dimensions 186 x 48 x 154 mm

Weight 391 g

Power External, 12V DC, 05A

Certifcations FCC, IC-03, CE, Wi-Fi (80211b,80211g), WPA2, WMM

Operating Temp 0 to 40ºC

Storage Temp -20 to 70ºC

Operating Humidity 10 to 85%, Noncondensing

Storage Humidity 5 to 90%, Noncondensing



Appendix C Warranty Information


Appendix C:Warranty Information

Limited Warranty

Linksys warrants that this Linksys hardware product will besubstantially ree o deects in materials and workmanshiparising under normal use during the Warranty Period,which begins on the date o purchase by the original end-user purchaser and lasts or the period speciied below:

Two (2) years or new product•

Ninety (90) days or reurbished product•

This limited warranty is non-transerable and extends onlyto the original end-user purchaser Your exclusive remedyand Linksys’ entire liability under this limited warrantywill be or Linksys, at its option, to (a) repair the product

with new or reurbished parts, (b) replace the productwith a reasonably available equivalent new or reurbishedLinksys product, or (c) reund the purchase price o theproduct less any rebates Any repaired or replacementproducts will be warranted or the remainder o theoriginal Warranty Period or thirty (30) days, whichever islonger All products and/or parts that are replaced becomethe property o Linksys

This limited warranty shall apply in addition to anystatutory or other rights which you may have under acontract o sale

Exclusions and LimitationsThis limited warranty does not apply i: (a) the productassembly seal has been removed or damaged, (b) theproduct has been altered or modiied, except by Linksys,(c) the product damage was caused by use with non-Linksys products, (d) the product has not been installed,operated, repaired, or maintained in accordance withinstructions supplied by Linksys, (e) the product hasbeen subjected to abnormal physical or electrical stress,misuse, negligence, or accident, () the serial number onthe Product has been altered, deaced, or removed, or (g)the product is supplied or licensed or beta, evaluation,

testing or demonstration purposes or which Linksys doesnot charge a purchase price or license ee

ALL SOFTWARE PROVIDED BY LINKSYS WITH THE PRODUCT,WHETHER FACTORY LOADED ON THE PRODUCT ORCONTAINED ON MEDIA ACCOMPANYING THE PRODUCT,IS PROVIDED “AS IS” WITHOUT ANY WARRANTY OF ANYKIND Without limiting the oregoing, Linksys does notwarrant that the operation o the product or sotware willbe uninterrupted or error ree Also, due to the continualdevelopment o new techniques or intruding upon andattacking networks, Linksys does not warrant that theproduct, service, sotware or any equipment, system or

network on which the product or sotware is used will beree o vulnerability to intrusion or attack The productmay include or be bundled with third party sotware orservice oerings This limited warranty shall not apply tosuch third party sotware or service oerings This limitedwarranty does not guarantee any continued availability

o a third party’s service or which this product’s use oroperation may require

TO THE EXTENT NOT PROHIBITED BY LAW, ALL IMPLIEDWARRANTIES AND CONDITIONS OF MERCHANTABILITY,SATISFACTORY QUALITY OR FITNESS FOR A PARTICULARPURPOSE ARE LIMITED TO THE DURATION OF THEWARRANTY PERIOD ALL OTHER EXPRESS OR IMPLIEDCONDITIONS, REPRESENTATIONS AND WARRANTIES,INCLUDING, BUT NOT LIMITED TO, ANY IMPLIEDWARRANTY OF NON-INFRINGEMENT, ARE DISCLAIMEDSome jurisdictions do not allow limitations on how longan implied warranty lasts, so the above limitation may notapply to you This limited warranty gives you speciic legalrights, and you may also have other rights which vary by

jurisdiction

TO THE EXTENT NOT PROHIBITED BY LAW, IN NO EVENTWILL LINKSYS BE LIABLE FOR ANY LOST DATA, REVENUEOR PROFIT, OR FOR SPECIAL, INDIRECT, CONSEQUENTIAL,INCIDENTAL OR PUNITIVE DAMAGES, REGARDLESS OF THETHEORY OF LIABILITY (INCLUDING NEGLIGENCE), ARISINGOUT OF OR RELATED TO THE USE OF OR INABILITY TOUSE THE PRODUCT (INCLUDING ANY SOFTWARE), EVENIF LINKSYS HAS BEEN ADVISED OF THE POSSIBILITY OFSUCH DAMAGES IN NO EVENT WILL LINKSYS’ LIABILITYEXCEED THE AMOUNT PAID BY YOU FOR THE PRODUCT

The oregoing limitations will apply even i any warrantyor remedy provided under this limited warranty ails o its essential purpose Some jurisdictions do not allowthe exclusion or limitation o incidental or consequentialdamages, so the above limitation or exclusion may notapply to you

Obtaining Warranty Service

I you have a question about your product or experience aproblem with it, please go to www.linksys.com/support where you will ind a variety o online support tools andinormation to assist you with your product I the product

proves deective during the Warranty Period, contactLinksys Technical Support or instructions on how toobtain warranty service The telephone number or LinksysTechnical Support in your area can be ound in the productUser Guide and at www.linksys.com Have your productserial number and proo o purchase on hand when callingA DATED PROOF OF ORIGINAL PURCHASE IS REQUIREDTO PROCESS WARRANTY CLAIMS I you are requested toreturn your product, you will be given a Return MaterialsAuthorization (RMA) number You are responsible orproperly packaging and shipping your product to Linksysat your cost and risk You must include the RMA number

http://www.linksys.com/support

http://www.linksys.com/





Appendix C Warranty Information


and a copy o your dated proo o original purchase whenreturning your product Products received without a RMAnumber and dated proo o original purchase will berejected Do not include any other items with the productyou are returning to Linksys Deective product coveredby this limited warranty will be repaired or replaced and

returned to you without charge Customers outside o the United States o America and Canada are responsibleor all shipping and handling charges, custom duties,VAT and other associated taxes and charges Repairs orreplacements not covered under this limited warranty willbe subject to charge at Linksys’ then-current rates

Technical Support

This limited warranty is neither a service nor asupport contract Inormation about Linksys’ currenttechnical support oerings and policies (includingany ees or support services) can be ound atwww.linksys.com/support

General

This limited warranty is governed by the laws o the jurisdiction in which the Product was purchased by you

I any portion o this limited warranty is ound to be voidor unenorceable, its remaining provisions shall remain inull orce and eect

Please direct all inquiries to: Linksys, PO Box 18558, Irvine,CA 92623

For more information, please contact us

www.linksys.com

Select your country, and then select SUPPORT/TECHNICAL

For product returns:

Select your Country and then select CUSTOMER SUPPORT







Appendix D Regulatory Information


Appendix D:Regulatory Information

FCC Statement

This product has been tested and complies with thespeciications or a Class B digital device, pursuant to Part15 o the FCC Rules These limits are designed to providereasonable protection against harmul intererence ina residential installation This equipment generates,uses, and can radiate radio requency energy and, i notinstalled and used according to the instructions, maycause harmul intererence to radio communicationsHowever, there is no guarantee that intererence will notoccur in a particular installation I this equipment doescause harmul intererence to radio or television reception,which is ound by turning the equipment o and on, the

user is encouraged to try to correct the intererence byone or more o the ollowing measures:

Reorient or relocate the receiving antenna•

Increase the separation between the equipment or•

devices

Connect the equipment to an outlet other than the•

receiver’s

Consult a dealer or an experienced radio/TV technician•

or assistance

FCC Radiation Exposure Statement

This equipment complies with FCC radiation exposurelimits set orth or an uncontrolled environment Thisequipment should be installed and operated withminimum distance 20 cm between the radiator and yourbody

Saety Notices

Caution: To reduce the risk o ire, use only No26 AWG•

or larger telecommunication line cord

Do not use this product near water, or example, in a•

wet basement or near a swimming pool

Avoid using this product during an electrical storm•

There may be a remote risk o electric shock romlightning

Industry Canada Statement

This Class B digital apparatus complies with CanadianICES-003 and RSS210

Operation is subject to the ollowing two conditions:

This device may not cause intererence and1

This device must accept any intererence, including2intererence that may cause undesired operationo the device

To reduce potential radio intererence to other users,the antenna type and its gain should be so chosenthat the EIRP is not more than required or successulcommunication

Industry Canada Radiation Exposure Statement

This equipment complies with IC radiation exposure limitsset orth or an uncontrolled environment This equipmentshould be installed and operated with minimum distance20 cm between the radiator & your body

This transmitter must not be co-located or operating inconjunction with any other antenna or transmitter

Avis d’Industrie Canada

Cet appareil numérique de la classe B est conorme auxnormes NMB-003 et RSS210 du Canada

L’utilisation de ce dispositi est autorisée seulement auxconditions suivantes :

il ne doit pas produire de brouillage et1il doit accepter tout brouillage radioélectrique reçu,2même si ce brouillage est susceptible de compromettre leonctionnement du dispositiAin de réduire le risque d’interérence aux autresutilisateurs, le type d’antenne et son gain doiventêtre choisis de açon à ce que la puissance isotroperayonnée équivalente (pire) ne soit pas supérieureau niveau requis pour obtenir une communicationsatisaisante

Avis d’Industrie Canada concernant l’exposition

aux radioréquencesCe matériel est conorme aux limites établies par ICen matière d’exposition aux radioréquences dans unenvironnement non contrôlé Ce matériel doit être installéet utilisé à une distance d’au moins 20 cm entre l’antenneet le corps de l’utilisateur

L’émetteur ne doit pas être placé près d’une autre antenneou d’un autre émetteur, ou onctionner avec une autreantenne ou un autre émetteur





Wireless Disclaimer

The maximum perormance or wireless is derived romIEEE Standard 80211 speciications Actual perormancecan vary, including lower wireless network capacity,data throughput rate, range and coverage Perormance

depends on many actors, conditions and variables,including distance rom the access point, volume o network traic, building materials and construction,operating system used, mix o wireless products used,intererence and other adverse conditions

Avis de non-responsabilité concernant les

appareils sans il

Les perormances maximales pour les réseaux sans ilsont tirées des spéciications de la norme IEEE 80211Les perormances réelles peuvent varier, notammenten onction de la capacité du réseau sans il, du débit

de la transmission de données, de la portée et de lacouverture Les perormances dépendent de acteurs,conditions et variables multiples, en particulier de ladistance par rapport au point d’accès, du volume du traicréseau, des matériaux utilisés dans le bâtiment et dutype de construction, du système d’exploitation et de lacombinaison de produits sans il utilisés, des interérenceset de toute autre condition déavorable





Declaration o Conormity with Regard to

EU Directive 1999/5/EC (R&TTE Directive)

Compliance Inormation or 2,4-GHz and 5-GHz WirelessProducts Relevant to the EU and Other Countries Followingthe EU Directive 1999/5/EC (R&TTE Directive)

Б ъ л г а р с к и[Bulgarian]

Това оборудване отговаря на същественитеизисквания и приложими клаузи наДиректива 1999/5/ЕС

Česky

[Czech]:

Toto zařízení je v souladu se základnímipožadavky a ostatními odpovídajícímiustanoveními Směrnice 1999/5/EC

Dansk

[Danish]:

Dette udstyr er i overensstemmelse medde væsentlige krav og andre relevantebestemmelser i Direktiv 1999/5/EF

Deutsch

[German]:

Dieses Gerät entspricht den grundlegendenAnorderungen und den weiterenentsprechenden Vorgaben der Richtlinie1999/5/EU

Eesti

[Estonian]:

See seade vastab direktiivi 1999/5/EÜ olulistelenõuetele ja teistele asjakohastele sätetele

English:This equipment is in compliance with theessential requirements and other relevantprovisions o Directive 1999/5/EC

Español

[Spanish]:

Este equipo cumple con los requisitos

esenciales asi como con otras disposicionesde la Directiva 1999/5/CE

Ελληνική

[Greek]:

Αυτός ο εξοπλισµός είναι σε συµµόρφωση µε τις ουσιώδεις απαιτήσεις και άλλες σχετικέςδιατάξεις της Οδηγίας 1999/5/EC

Français

[French]:

Cet appareil est conorme aux exigencesessentielles et aux autres dispositionspertinentes de la Directive 1999/5/EC

Íslenska

[Icelandic]:

Þetta tæki er samkvæmt grunnkröum ogöðrum viðeigandi ákvæðum Tilskipunar1999/5/EC

Italiano

[Italian]:

Questo apparato é conorme ai requisitiessenziali ed agli altri principi sanciti dallaDirettiva 1999/5/CE

Latviski

[Latvian]:

Šī iekārta atbilst Direktīvas 1999/5/EK būtiskajām prasībām un citiem ar tosaistītajiem noteikumiem

Lietuvių

[Lithuanian]:

Šis įrenginys tenkina 1999/5/EB Direktyvosesminius reikalavimus ir kitas šios direktyvosnuostatas

Nederlands

[Dutch]:

Dit apparaat voldoet aan de essentiele eisenen andere van toepassing zijnde bepalingenvan de Richtlijn 1999/5/EC

Malti

[Maltese]:

Dan l-apparat huwa konormi mal-ħtiġietessenzjali u l-provedimenti l-oħra rilevanti

tad-Direttiva 1999/5/EC

Magyar

[Hungarian]:

Ez a készülék teljesíti az alapvetőkövetelményeket és más 1999/5/EK irányelvben meghatározott vonatkozórendelkezéseket

Norsk

[Norwegian]:

Dette utstyret er i samsvar med degrunnleggende krav og andre relevantebestemmelser i EU-direktiv 1999/5/EF

Polski

[Polish]:

Urządzenie jest zgodne z ogólnymiwymaganiami oraz szczególnymi warunkamiokreślonymi Dyrektywą UE: 1999/5/EC

Português

[Portuguese]:

Este equipamento está em conormidade comos requisitos essenciais e outras provisõesrelevantes da Directiva 1999/5/EC

Română

[Romanian]

Acest echipament este in conormitatecu cerintele esentiale si cu alte prevederirelevante ale Directivei 1999/5/EC

Slovensko

[Slovenian]:

Ta naprava je skladna z bistvenimi zahtevamiin ostalimi relevantnimi pogoji Direktive1999/5/EC

Slovensky[Slovak]:

Toto zariadenie je v zhode so základnýmipožiadavkami a inými príslušnými nariadeniamidirektív: 1999/5/EC

Suomi

[Finnish]:

Tämä laite täyttää direktiivin 1999/5/EYolennaiset vaatimukset ja on siinä asetettujenmuiden laitetta koskevien määräystenmukainen

Svenska

[Swedish]:

Denna utrustning är i överensstämmelse medde väsentliga kraven och andra relevantabestämmelser i Direktiv 1999/5/EC

For all products, the Declaration o Conormity (DoC) is

available through one or more o these options:A pd ile is included on the product’s CD•

A print copy is included with the product•

A pd ile is available on the product’s webpage•

Visit www.linksys.com/internationaland select yourcountry or region Then select your product

I you need any other technical documentation, see the“Technical Documents on wwwlinksyscom/international”section, as shown later in this appendix





Wireless Equipment

(Wireless-N/G/A/B Products)

The ollowing standards were applied during theassessment o the product against the requirements o the Directive 1999/5/EC:

Radio: EN 300 328 and/or EN 301 893 as applicable•

EMC: EN 301 489-1, EN 301 489-17•

Saety: EN 60950 and either EN 50385 or EN 50371•

Dynamic Frequency Selection (DFS) and Transmit PowerControl (TPC) are required or operation in the 5 GHzband

DFS: The equipment meets the DFS requirements asdeined in ETSI EN 301 893 This eature is required bythe regulations to avoid intererence with Radio LocationServices (radars)

TPC: For operation in the 5 GHz band, the maximum powerlevel is 3 dB or more below the applicable limit As such,TPC is not required

CE Marking

For the Linksys Wireless-N, -G, -B, and/or -A products,the ollowing CE mark, notiied body number (whereapplicable), and class 2 identiier are added to theequipment

or

or

or

Check the CE label on the product to ind out whichnotiied body was involved during the assessment

National Restrictions

This product may be used in all EU countries (and othercountries ollowing the EU directive 1999/5/EC) withoutany limitation except or the countries mentioned below:

Ce produit peut être utilisé dans tous les pays de l’UE (et dans

tous les pays ayant transposés la directive 1999/5/CE) sansaucune limitation, excepté pour les pays mentionnés ci-

dessous:

Questo prodotto è utilizzabile in tutte i paesi EU (ed in tutti

gli altri paesi che seguono le direttive EU 1999/5/EC) senza

nessuna limitazione, eccetto per i paesi menzionati di

seguito:

Das Produkt kann in allen EU Staaten ohne Einschränkungen

eingesetzt werden (sowie in anderen Staaten die der EU

Direktive 1999/5/CE folgen) mit Außnahme der folgenden

aufgeführten Staaten:

In the majority o the EU and other European countries,the 2,4- and 5-GHz bands have been made availableor the use o wireless local area networks (LANs) Thetable labeled “Overview o Regulatory Requirements orWireless LANs” provides an overview o the regulatoryrequirements applicable or the 2,4- and 5-GHz bands

Later in this document you will ind an overview o countries in which additional restrictions or requirementsor both are applicable

The requirements or any country may evolve Linksysrecommends that you check with the local authorities orthe latest status o their national regulations or both the

2,4- and 5-GHz wireless LANs

Overview of Regulatory Requirements for Wireless LANs

Frequency

Band (MHz)

Max Power Level

(EIRP) (mW)

Indoor

ONLY

Indoor &

Outdoor

2400-24835 100 X

5150-5350† 200 X

5470-5725† 1000 X

Dynamic Frequency Selection and Transmit Power Control are†

required in the requency ranges o 5250-5350 MHz and 5470-5725

MHz

The ollowing countries have restrictions and/orrequirements in addition to those given in the tablelabeled “Overview o Regulatory Requirements orWireless LANs”:

Denmark

In Denmark, the band 5150 - 5350 MHz is also allowed oroutdoor usage

I Danmark må frekvensbåndet 5150 - 5350 også anvendes

udendørs.





France

For 2,4 GHz, the product should not be used outdoorsin the band 2454 - 2483,5 MHz There are no restrictionswhen used in other parts o the 2,4 GHz band when usedindoors Check http://wwwarcepr/ or more details

Pour la bande 2,4 GHz, l’ équipement ne doit pas être utiliséen extérieur dans la bande 2454 - 2483,5 MHz. Il n’y a pas de

restrictions pour des utilisations en intérieur dans d’autres

parties de la bande 2,4GHz. Consultez http://www.arcep.fr/

pour de plus amples détails.

Applicable Power Levels in France

LocationFrequency

Range (MHz)Power (EIRP)

Indoor

(No restrictions)2400-24835 100 mW (20 dBm)

Outdoor 2400-24542454-24835

100 mW (20 dBm)10 mW (10 dBm)

Italy

This product meets the National Radio Interace andthe requirements speciied in the National FrequencyAllocation Table or Italy Unless this 2,4-GHz wireless LANproduct is operating within the boundaries o the owner’sproperty, its use requires a “general authorization” Pleasecheck http://wwwcomunicazioniit/it/ or more details

Questo prodotto è conforme alla specifiche di InterfacciaRadio Nazionali e rispetta il Piano Nazionale di ripartizione

delle frequenze in Italia. Se non viene installato all’interno

del proprio fondo, l’utilizzo di prodotti Wireless LAN a

2,4 GHz richiede una “Autorizzazione Generale”. Consultare

http://www.comunicazioni.it/it/ per maggiori dettagli.

Latvia

The outdoor usage o the 2,4 GHz band requires anauthorization rom the Electronic Communications OicePlease check http://wwwesdlv or more details

2,4 GHz frekveču joslas izmantošanai ārpus telpām

nepieciešama atļauja no Elektronisko sakaru direkcijas.

Vairāk informācijas: http://www.esd.lv.

Notes:

Although Norway, Switzerland and Liechtenstein are1not EU member states, the EU Directive 1999/5/EC hasalso been implemented in those countries

The regulatory limits or maximum output power are2speciied in EIRP The EIRP level o a device can becalculated by adding the gain o the antenna used(speciied in dBi) to the output power available at theconnector (speciied in dBm)

Product Usage Restrictions

This product is designed or indoor usage only Outdoorusage is not recommended, unless otherwise noted

2,4 GHz Restrictions

This product is designed or use with the standard, integralor dedicated (external) antenna(s) that is/are shippedtogether with the equipment However, some applicationsmay require the antenna(s), i removable, to be separatedrom the product and installed remotely rom the deviceby using extension cables For these applications, Linksysoers an R-SMA extension cable (AC9SMA) and an R-TNCextension cable (AC9TNC) Both o these cables are 9meters long and have a cable loss (attenuation) o 5 dB Tocompensate or the attenuation, Linksys also oers highergain antennas, the HGA7S (with R-SMA connector) andHGA7T (with R-TNC connector) These antennas have again o 7 dBi and may only be used with either the R-SMAor R-TNC extension cable

Combinations o extension cables and antennas resultingin a radiated power level exceeding 100 mW EIRP areillegal

Third-Party Sotware or Firmware

The use o sotware or irmware not supported/providedby Linksys may result that the equipment is no longercompliant with the regulatory requirements

Technical Documents on

www.linksys.com/internationalFollow these steps to access technical documents:

Enter http://wwwlinksyscom/international in your1web browser

Select the country or region in which you live2

Click the3 Products tab

Select the appropriate product category4

Select the product sub-category, i necessary5

Select the product6

Select the type o documentation you want rom the7 More Inormation section The document will openin PDF ormat i you have Adobe Acrobat installed onyour computer

NOTE: I you have questions regardingthe compliance o this product or youcannot ind the inormation you need,please contact your local sales oice or visitwww.linksys.com/international





User Inormation or Consumer Products

Covered by EU Directive 2002/96/EC on

Waste Electric and Electronic Equipment

(WEEE)

This document contains important inormation or userswith regards to the proper disposal and recycling o Linksys products Consumers are required to comply withthis notice or all electronic products bearing the ollowingsymbol:

English - Environmental Information for Customers inthe European Union

European Directive 2002/96/EC requires that the equipmentbearing this symbol on the product and/or its packaging mustnot be disposed o with unsorted municipal waste The symbolindicates that this product should be disposed o separatelyrom regular household waste streams It is your responsibility todispose o this and other electric and electronic equipment viadesignated collection acilities appointed by the government orlocal authorities Correct disposal and recycling will help preventpotential negative consequences to the environment andhuman health For more detailed inormation about the disposal

o your old equipment, please contact your local authorities,waste disposal service, or the shop where you purchased theproduct

Български (Bulgarian) - Информация относноопазването на околната среда за потребители вЕвропейския съюз

Европейска директива 2002/96/EC изисква уредите, носещитози символ върху изделието и/или опаковката му, да несе изхвърля т с несортирани битови отпадъци Символътобозначава, че изделието трябва да се изхвърля отделно отсметосъбирането на обикновените битови отпадъци Вашае отговорността този и другите електрически и електронни

уреди да се изхвърлят в предварително определени отдържавните или общински органи специализирани пунктовеза събиране Правилното изхвърляне и рециклиранеще спомогнат да се предотвратят евентуални вредни заоколната среда и здравето на населението последствия Запо-подробна информация относно изхвърлянето на вашитестари уреди се обърнете към местните власти, службите засметосъбиране или магазина, от който сте закупили уреда

Ceština (Czech) - Informace o ochraně životníhoprostředí pro zákazníky v zemích Evropské unie

Evropská směrnice 2002/96/ES zakazuje, aby zařízení označenétímto symbolem na produktu anebo na obalu bylo likvidovános netříděným komunálním odpadem Tento symbol udává,že daný produkt musí být likvidován odděleně od běžnéhokomunálního odpadu Odpovídáte za likvidaci tohoto produktu

a dalších elektrických a elektronických zařízení prostřednictvímurčených sběrných míst stanovených vládou nebo místnímiúřady Správná likvidace a recyklace pomáhá předcházetpotenciálním negativním dopadům na životní prostředí a lidskézdraví Podrobnější inormace o likvidaci starého vybavení silaskavě vyžádejte od místních úřadů, podniku zabývajícího selikvidací komunálních odpadů nebo obchodu, kde jste produktzakoupili

Dansk (Danish) - Miljøinformation for kunder i EU

EU-direktiv 2002/96/EF kræver, at udstyr der bærer dette symbolpå produktet og/eller emballagen ikke må bortskaes som

usorteret kommunalt aald Symbolet betyder, at dette produkt

skal bortskaes adskilt ra det almindelige husholdningsaaldDet er dit ansvar at bortskae dette og andet elektrisk ogelektronisk udstyr via bestemte indsamlingssteder udpegeta staten eller de lokale myndigheder Korrekt bortskaelseog genvinding vil hjælpe med til at undgå mulige skader ormiljøet og menneskers sundhed Kontakt venligst de lokalemyndigheder, renovationstjenesten eller den butik, hvor duhar købt produktet, angående mere detaljeret inormation ombortskaelse a dit gamle udstyr

Deutsch (German) - Umweltinformation für Kundeninnerhalb der Europäischen Union

Die Europäische Richtlinie 2002/96/EC verlangt, dass technische

Ausrüstung, die direkt am Gerät und/oder an der Verpackung mitdiesem Symbol versehen ist , nicht zusammen mit unsortiertemGemeindeaball entsorgt werden dar Das Symbol weist darau hin, dass das Produkt von regulärem Haushaltmüll getrenntentsorgt werden sollte Es liegt in Ihrer Verantwortung, diesesGerät und andere elektrische und elektronische Geräte überdie daür zuständigen und von der Regierung oder örtlichenBehörden dazu bestimmten Sammelstellen zu entsorgenOrdnungsgemäßes Entsorgen und Recyceln trägt dazu bei,potentielle negative Folgen ür Umwelt und die menschlicheGesundheit zu vermeiden Wenn Sie weitere Inormationen zurEntsorgung Ihrer Altgeräte benötigen, wenden Sie sich bitte andie örtlichen Behörden oder städtischen Entsorgungsdiensteoder an den Händler, bei dem Sie das Produkt erworben haben





Eesti (Estonian) - Keskkonnaalane informatsioonEuroopa Liidus asuvatele klientidele

Euroopa Liidu direktiivi 2002/96/EÜ nõuete kohaselt onseadmeid, millel on tootel või pakendil käesolev sümbol ,keelatud kõrvaldada koos sorteerimata olmejäätmetega Seesümbol näitab, et toode tuleks kõrvaldada eraldi tavalistestolmejäätmevoogudest Olete kohustatud kõrvaldama käesoleva

ja ka muud elektri- ja elektroonikaseadmed riigi või kohalikeametiasutuste poolt ette nähtud kogumispunktide kauduSeadmete korrektne kõrvaldamine ja ringlussevõtt aitab vältidavõimalikke negatiivseid tagajärgi keskkonnale ning inimestetervisele Vanade seadmete kõrvaldamise kohta täpsemainormatsiooni saamiseks võtke palun ühendust kohalikeametiasutustega, jäätmekäitlusirmaga või kauplusega, kust tetoote ostsite

Español (Spanish) - Información medioambiental paraclientes de la Unión Europea

La Directiva 2002/96/CE de la UE exige que los equipos quelleven este símbolo en el propio aparato y/o en su embalaje

no deben eliminarse junto con otros residuos urbanos noseleccionados El símbolo indica que el producto en cuestióndebe separarse de los residuos domésticos convencionales convistas a su eliminación Es responsabilidad suya desechar este ycualesquiera otros aparatos eléctricos y electrónicos a través delos puntos de recogida que ponen a su disposición el gobierno ylas autoridades locales Al desechar y reciclar correctamente estosaparatos estará contribuyendo a evitar posibles consecuenciasnegativas para el medio ambiente y la salud de las personas Sidesea obtener inormación más detallada sobre la eliminaciónsegura de su aparato usado, consulte a las autoridades locales,al servicio de recogida y eliminación de residuos de su zona opregunte en la tienda donde adquirió el producto

ξλληνικά (Greek) - Στοιχεία περιβαλλοντικήςπροστασίας για πελάτες εντός της ΕυρωπαϊκήςΈνωσης

Η Κοινοτική Οδηγία 2002/96/EC απαιτεί ότι ο εξοπλισμός ο οποίοςφέρει αυτό το σύμβολο στο προϊόν και/ή στη συσκευασία του δεν πρέπει να απορρίπτεται μαζί με τα μικτά κοινοτικάαπορρίμματα Το σύμβολο υποδεικνύει ότι αυτό το προϊόν θαπρέπει να απορρίπτεται ξεχωριστά από τα συνήθη οικιακάαπορρίμματα Είστε υπεύθυνος για την απόρριψη του παρόντοςκαι άλλου ηλεκτρικού και ηλεκτρονικού εξοπλισμού μέσω τωνκαθορισμένων εγκαταστάσεων συγκέντρωσης απορριμμάτων οιοποίες παρέχονται από το κράτος ή τις αρμόδιες τοπικές αρχέςΗ σωστή απόρριψη και ανακύκλωση συμβάλλει στην πρόληψη

πιθανών αρνητικών συνεπειών για το περιβάλλον και την υγείαΓια περισσότερες πληροφορίες σχετικά με την απόρριψη τουπαλιού σας εξοπλισμού, παρακαλώ επικοινωνήστε με τις τοπικέςαρχές, τις υπηρεσίες απόρριψης ή το κατάστημα από το οποίοαγοράσατε το προϊόν

Français (French) - Informations environnementalespour les clients de l’Union européenne

La directive européenne 2002/96/CE exige que l’équipementsur lequel est apposé ce symbole sur le produit et/ou sonemballage ne soit pas jeté avec les autres ordures ménagères Cesymbole indique que le produit doit être éliminé dans un circuitdistinct de celui pour les déchets des ménages Il est de votre

responsabilité de jeter ce matériel ainsi que tout autre matérielélectrique ou électronique par les moyens de collecte indiquéspar le gouvernement et les pouvoirs publics des collectivitésterritoriales L’élimination et le recyclage en bonne et due ormeont pour but de lutter contre l’impact néaste potentiel de cetype de produits sur l’environnement et la santé publique Pourplus d’inormations sur le mode d’élimination de votre ancienéquipement, veuillez prendre contact avec les pouvoirs publicslocaux, le service de traitement des déchets, ou l’endroit où vousavez acheté le produit

Italiano (Italian) - Informazioni relative all’ambienteper i clienti residenti nell’Unione Europea

La direttiva europea 2002/96/EC richiede che le apparecchiaturecontrassegnate con questo simbolo sul prodotto e/osull’imballaggio non siano smaltite insieme ai riiuti urbaninon dierenziati Il simbolo indica che questo prodotto nondeve essere smaltito insieme ai normali riiuti domestici Èresponsabilità del proprietario smaltire sia questi prodotti siale altre apparecchiature elettriche ed elettroniche mediantele speciiche strutture di raccolta indicate dal governo o daglienti pubblici locali Il corretto smaltimento ed il riciclaggioaiuteranno a prevenire conseguenze potenzialmente negativeper l’ambiente e per la salute dell’essere umano Per ricevereinormazioni più dettagliate circa lo smaltimento delle vecchieapparecchiature in Vostro possesso, Vi invitiamo a contattare glienti pubblici di competenza, il servizio di smaltimento riiuti o il

negozio nel quale avete acquistato il prodotto

Latviešu valoda (Latvian) - Ekoloģiska informācijaklientiem Eiropas Savienības jurisdikcijā

Direktīvā 2002/96/EK ir prasība, ka aprīkojumu, kam pievienotazīme uz paša izstrādājuma vai uz tā iesaiņojuma, nedrīkstizmest nešķirotā veidā kopā ar komunālajiem atkritumiem(tiem, ko rada vietēji iedzīvotāji un uzņēmumi) Šī zīme nozīmēto, ka šī ierīce ir jāizmet atkritumos tā, lai tā nenonāktu kopā arparastiem mājsaimniecības atkritumiem Jūsu pienākums ir šoun citas elektriskas un elektroniskas ierīces izmest atkritumos,izmantojot īpašus atkritumu savākšanas veidus un līdzekļus, konodrošina valsts un pašvaldību iestādes Ja izmešana atkritumos

un pārstrāde tiek veikta pareizi, tad mazinās iespējamaiskaitējums dabai un cilvēku veselībai Sīkākas ziņas parnovecojuša aprīkojuma izmešanu atkritumos jūs varat saņemtvietējā pašvaldībā, atkritumu savākšanas dienestā, kā arī veikalā,kur iegādājāties šo izstrādājumu





Lietuvškai (Lithuanian) - Aplinkosaugos informacija,skirta Europos Sąjungos vartotojams

Europos direktyva 2002/96/EC numato, kad įrangos, kuri irkurios pakuotė yra pažymėta šiuo simboliu (įveskite simbolį),negalima šalinti kartu su nerūšiuotomis komunalinėmisatliekomis Šis simbolis rodo, kad gaminį reikia šalinti atskirainuo bendro buitinių atliekų srauto Jūs privalote užtikrinti, kad

ši ir kita elektros ar elektroninė įranga būtų šalinama per tamtikras nacionalinės ar vietinės valdžios nustatytas atliekų rinkimosistemas Tinkamai šalinant ir perdirbant atliekas, bus išvengtagalimos žalos aplinkai ir žmonių sveikatai Daugiau inormacijosapie jūsų senos įrangos šalinimą gali pateikti vietinės valdžiosinstitucijos, atliekų šalinimo tarnybos arba parduotuvės, kurioseįsigijote tą gaminį

Malti (Maltese) - Informazzjoni Ambjentali għal Klijentifl-Unjoni Ewropea

Id-Direttiva Ewropea 2002/96/KE titlob li t-tagħmir li jkun ih is-simbolu uq il-prodott u/jew uq l-ippakkjar ma jistax jintremama’ skart muniċipali li ma ġiex isseparat Is-simbolu jindika

li dan il-prodott għandu jintrema separatament minn ma’ l-iskart domestiku regolari Hija responsabbiltà tiegħek li tarmidan it-tagħmir u kull tagħmir ieħor ta’ l-elettriku u elettronikupermezz ta’ aċilitajiet ta’ ġbir appuntati apposta mill-gvern jewmill-awtoritajiet lokali Ir-rimi b’mod korrett u r-riċiklaġġ jgħin jipprevjeni konsegwenzi negattivi potenzjali għall-ambjent ugħas-saħħa tal-bniedem Għal aktar inormazzjoni dettaljatadwar ir-rimi tat-tagħmir antik tiegħek, jekk jogħġbok ikkuntattjalill-awtoritajiet lokali tiegħek, is-servizzi għar-rimi ta’ l-iskart, jewil-ħanut minn ejn xtrajt il-prodott

Magyar (Hungarian) - Környezetvédelmi információ azeurópai uniós vásárlók számára

A 2002/96/EC számú európai uniós irányelv megkívánja, hogyazokat a termékeket, amelyeken, és/vagy amelyek csomagolásánaz alábbi címke megjelenik, tilos a többi szelektálatlan lakosságihulladékkal együtt kidobni A címke azt jelöli, hogy az adotttermék kidobásakor a szokványos háztartási hulladékelszállításirendszerektõl elkülönített eljárást kell alkalmazni Az Önelelõssége, hogy ezt, és más elektromos és elektronikusberendezéseit a kormányzati vagy a helyi hatóságok általkijelölt gyűjtõredszereken keresztül számolja el A megelelõhulladékeldolgozás segít a környezetre és az emberi egészségrepotenciálisan ártalmas negatív hatások megelõzésében Haelavult berendezéseinek elszámolásához további részletesinormációra van szüksége, kérjük, lépjen kapcsolatba a helyihatóságokkal, a hulladékeldolgozási szolgálattal, vagy azzal

üzlettel, ahol a terméket vásárolta

Nederlands (Dutch) - Milieu-informatie voor klantenin de Europese Unie

De Europese Richtlijn 2002/96/EC schrijt voor dat apparatuur dieis voorzien van dit symbool op het product o de verpakking,niet mag worden ingezameld met niet-gescheiden huishoudelijk aval Dit symbool geet aan dat het product apart moet wordeningezameld U bent zel verantwoordelijk voor de vernietiging

van deze en andere elektrische en elektronische apparatuur via dedaarvoor door de landelijke o plaatselijke overheid aangewezeninzamelingskanalen De juiste vernietiging en recycling vandeze apparatuur voorkomt mogelijke negatieve gevolgen voorhet milieu en de gezondheid Voor meer inormatie over hetvernietigen van uw oude apparatuur neemt u contact op metde plaatselijke autoriteiten o avalverwerkingsdienst, o met dewinkel waar u het product hebt aangeschat

Norsk (Norwegian) - Miljøinformasjon for kunder i EU

EU-direktiv 2002/96/EF krever at utstyr med ølgende symbolavbildet på produktet og/eller pakningen, ikke må kastes

sammen med usortert avall Symbolet indikerer at dette

produktet skal håndteres atskilt ra ordinær avallsinnsamlingor husholdningsavall Det er ditt ansvar å kvitte deg meddette produktet og annet elektrisk og elektronisk avall via egneinnsamlingsordninger slik myndighetene eller kommunenebestemmer Korrekt avallshåndtering og gjenvinning vilvære med på å orhindre mulige negative konsekvenser ormiljø og helse For nærmere inormasjon om håndtering avdet kasserte utstyret ditt, kan du ta kontakt med kommunen,en innsamlingsstasjon or avall eller butikken der du kjøpteproduktet

Polski (Polish) - Informacja dla klientów w UniiEuropejskiej o przepisach dotyczących ochrony

środowiskaDyrektywa Europejska 2002/96/EC wymaga, aby sprzętoznaczony symbolem znajdującym się na produkcie i/lub jegoopakowaniu nie był wyrzucany razem z innymi niesortowanymiodpadami komunalnymi Symbol ten wskazuje, że produktnie powinien być usuwany razem ze zwykłymi odpadami zgospodarstw domowych Na Państwu spoczywa obowiązek wyrzucania tego i innych urządzeń elektrycznych orazelektronicznych w punktach odbioru wyznaczonych przez władzekrajowe lub lokalne Pozbywanie się sprzętu we właściwy sposóbi jego recykling pomogą zapobiec potencjalnie negatywnymkonsekwencjom dla środowiska i zdrowia ludzkiego W celuuzyskania szczegółowych inormacji o usuwaniu starego sprzętu,prosimy zwrócić się do lokalnych władz, służb oczyszczania

miasta lub sklepu, w którym produkt został nabyty





Português (Portuguese) - Informação ambiental paraclientes da União Europeia

A Directiva Europeia 2002/96/CE exige que o equipamentoque exibe este símbolo no produto e/ou na sua embalagemnão seja eliminado junto com os resíduos municipais nãoseparados O símbolo indica que este produto deve sereliminado separadamente dos resíduos domésticos regulares

É da sua responsabilidade eliminar este e qualquer outroequipamento eléctrico e electrónico através das instalaçõesde recolha designadas pelas autoridades governamentais oulocais A eliminação e reciclagem correctas ajudarão a preveniras consequências negativas para o ambiente e para a saúdehumana Para obter inormações mais detalhadas sobre aorma de eliminar o seu equipamento antigo, contacte asautoridades locais, os serviços de eliminação de resíduos ou oestabelecimento comercial onde adquiriu o produto

Română (Romanian) - Informaţii de mediu pentruclienţii din Uniunea Europeană

Directiva europeană 2002/96/CE impune ca echipamentele care

prezintă acest simbol pe produs şi/sau pe ambalajul acestuia sănu ie casate împreună cu gunoiul menajer municipal Simbolulindică aptul că acest produs trebuie să ie casat separat degunoiul menajer obişnuit Este responsabilitatea dvs să casaţiacest produs şi alte echipamente electrice şi electronice prinintermediul unităţilor de colectare special desemnate de guvernsau de autorităţile locale Casarea şi reciclarea corecte vor ajutala prevenirea potenţialelor consecinţe negative asupra sănătăţiimediului şi a oamenilor Pentru mai multe inormaţii detaliatecu privire la casarea acestui echipament vechi, contactaţiautorităţile locale, serviciul de salubrizare sau magazinul de lacare aţi achiziţionat produsul

Slovenčina (Slovak) - Informácie o ochrane životnéhoprostredia pre zákazníkov v Európskej únii

Podľa európskej smernice 2002/96/ES zariadenie s týmtosymbolom na produkte a/alebo jeho balení nesmie byť likvidované spolu s netriedeným komunálnym odpadomSymbol znamená, že produkt by sa mal likvidovať oddeleneod bežného odpadu z domácností Je vašou povinnosťoulikvidovať toto i ostatné elektrické a elektronické zariadeniaprostredníctvom špecializovaných zberných zariadení určenýchvládou alebo miestnymi orgánmi Správna likvidácia a recykláciapomôže zabrániť prípadným negatívnym dopadom na životnéprostredie a zdravie ľudí Ak máte záujem o podrobnejšieinormácie o likvidácii starého zariadenia, obráťte sa, prosím, namiestne orgány, organizácie zaoberajúce sa likvidáciou odpadov

alebo obchod, v ktorom ste si produkt zakúpili

Slovenčina (Slovene) - Okoljske informacije za strankev Evropski uniji

Evropska direktiva 2002/96/EC prepoveduje odlaganje opreme,označene s tem simbolom – na izdelku in/ali na embalaži – medobičajne, nerazvrščene odpadke Ta simbol opozarja, da je trebaizdelek odvreči ločeno od preostalih gospodinjskih odpadkovVaša odgovornost je, da to in preostalo električno in elektronsko

opremo odnesete na posebna zbirališča, ki jih določijodržavne ustanove ali lokalna uprava S pravilnim odlaganjemin recikliranjem boste preprečili morebitne škodljive vplive naokolje in zdravje ljudi Če želite izvedeti več o odlaganju stareopreme, se obrnite na lokalno upravo, odpad ali trgovino, kjerste izdelek kupili

Suomi (Finnish) - Ympäristöä koskevia tietoja EU-alueen asiakkaille

EU-direktiivi 2002/96/EY edellyttää, että jos laitteistossa on tämäsymboli itse tuotteessa ja/tai sen pakkauksessa, laitteistoaei saa hävittää lajittelemattoman yhdyskuntajätteen mukanaSymboli merkitsee sitä, että tämä tuote on hävitettävä erillään

tavallisesta kotitalousjätteestä Sinun vastuullasi on hävittäätämä elektroniikkatuote ja muut vastaavat elektroniikkatuotteetviemällä tuote tai tuotteet viranomaisten määräämäänkeräyspisteeseen Laitteiston oikea hävittäminen estäämahdolliset kielteiset vaikutukset ympäristöön ja ihmistenterveyteen Lisätietoja vanhan laitteiston oikeasta hävitystavastasaa paikallisilta viranomaisilta, jätteenhävityspalvelusta tai siitämyymälästä, josta ostit tuotteen

Svenska (Swedish) - Miljöinformation för kunder iEuropeiska unionen

Det europeiska direktivet 2002/96/EC kräver att utrustning meddenna symbol på produkten och/eller örpackningen inte år

kastas med osorterat kommunalt avall Symbolen visar att dennaprodukt bör kastas eter att den avskiljts rån vanligt hushållsavallDet aller på ditt ansvar att kasta denna och annan elektrisk ochelektronisk utrustning på astställda insamlingsplatser utseddaav regeringen eller lokala myndigheter Korrekt kassering ochåtervinning skyddar mot eventuella negativa konsekvenserör miljön och personhälsa För mer detaljerad inormation omkassering av din gamla utrustning kontaktar du dina lokalamyndigheter, avallshanteringen eller butiken där du köpteprodukten

WEB: For additional inormation, please visitwww.linksys.com/international

8040410A-ST



35

Appendix E Software License Agreement

Wireless-G Broadband Router

Appendix E: SoftwareLicense Agreement

Sotware in Linksys Products

This product rom Cisco-Linksys LLC or rom one o itsailiates Cisco Systems-Linksys (Asia) Pte Ltd or Cisco-Linksys KK (“Linksys”) contains sotware (includingirmware) originating rom Linksys and its suppliersand may also contain sotware rom the open sourcecommunity Any sotware originating rom Linksys and itssuppliers is licensed under the Linksys Sotware LicenseAgreement contained at Schedule 1 below You may alsobe prompted to review and accept that Linksys SotwareLicense Agreement upon installation o the sotware

Any sotware rom the open source community is licensedunder the speciic license terms applicable to that sotwaremade available by Linksys at www.linksys.com/gpl or asprovided or in Schedules 2, 3 and 4 below

Where such speciic license terms entitle you to the sourcecode o such sotware, that source code is upon requestavailable at cost rom Linksys or at least three yearsrom the purchase date o this product and may also beavailable or download rom www.linksys.com/gpl Fordetailed license terms and additional inormation onopen source sotware in Linksys products please look atthe Linksys public web site at: www.linksys.com/gpl/ orSchedules 2, 3 or 4 below as applicable

BY DOWNLOADING OR INSTALLING THE SOFTWARE,OR USING THE PRODUCT CONTAINING THE SOFTWARE,YOU ARE CONSENTING TO BE BOUND BY THE SOFTWARELICENSE AGREEMENTS BELOW IF YOU DO NOT AGREE TOALL OF THESE TERMS, THEN YOU MAY NOT DOWNLOAD,INSTALL OR USE THE SOFTWARE YOU MAY RETURNUNUSED SOFTWARE (OR, IF THE SOFTWARE IS SUPPLIEDAS PART OF ANOTHER PRODUCT, THE UNUSED PRODUCT )FOR A FULL REFUND UP TO 30 DAYS AFTER ORIGINALPURCHASE, SUBJECT TO THE RETURN PROCESS ANDPOLICIES OF THE PARTY FROM WHICH YOU PURCHASEDSUCH PRODUCT OR SOFTWARE

Sotware LicensesThe sotware Licenses applicable to sotware rom Linksysare made available at the Linksys public web site at:www.linksys.com For your convenience o reerence, acopy o the Linksys Sotware License Agreement and themain open source code licenses used by Linksys in itsproducts are contained in the Schedules below

Schedule 1 - Linksys Sotware License Agreement

THIS LICENSE AGREEMENT IS BETWEEN YOU ANDCISCO-LINKSYS LLC OR ONE OF ITS AFFILIATES CISCOSYSTEMS-LINKSYS (ASIA) PTE LTD OR CISCO-LINKSYSKK (“LINKSYS”) LICENSING THE SOFTWARE INSTEAD OFCISCO-LINKSYS LLC BY DOWNLOADING OR INSTALLINGTHE SOFTWARE, OR USING THE PRODUCT CONTAININGTHE SOFTWARE, YOU ARE CONSENTING TO BE BOUND BYTHIS AGREEMENT IF YOU DO NOT AGREE TO ALL OF THESETERMS, THEN YOU MAY NOT DOWNLOAD, INSTALL OR USETHE SOFTWARE YOU MAY RETURN UNUSED SOFTWARE(OR, IF THE SOFTWARE IS SUPPLIED AS PART OF ANOTHERPRODUCT, THE UNUSED PRODUCT) FOR A FULL REFUNDUP TO 30 DAYS AFTER ORIGINAL PURCHASE, SUBJECT TOTHE RETURN PROCESS AND POLICIES OF THE PARTY FROMWHICH YOU PURCHASED SUCH PRODUCT OR SOFTWARE

License. Subject to the terms and conditions o thisAgreement, Linksys grants the original end user purchaser

o the Linksys product containing the Sotware (“You”)a nonexclusive license to use the Sotware solely asembedded in or (where authorized in the applicabledocumentation) or communication with such productThis license may not be sublicensed, and is not transerableexcept to a person or entity to which you transerownership o the complete Linksys product containingthe Sotware, provided you permanently transer all rightsunder this Agreement and do not retain any ull or partialcopies o the Sotware, and the recipient agrees to theterms o this Agreement

“Sotware” includes, and this Agreement will apply to

(a) the sotware o Linksys or its suppliers provided in orwith the applicable Linksys product, excluding technologyrom the open source community, and (b) any upgrades,updates, bug ixes or modiied versions (“Upgrades”) orbackup copies o the Sotware supplied to You by Linksysor an authorized reseller, provided you already hold avalid license to the original sotware and have paid anyapplicable ee or the Upgrade

Protection o Inormation. The Sotware anddocumentation contain trade secrets and/or copyrightedmaterials o Linksys or its suppliers You will not copyor modiy the Sotware or decompile, decrypt, reverse

engineer or disassemble the Sotware (except to theextent expressly permitted by law notwithstanding thisprovision), and You will not disclose or make availablesuch trade secrets or copyrighted material in any ormto any third party Title to and ownership o the Sotwareand documentation and any portion thereo, will remainsolely with Linksys or its suppliers

Collection and Processing o Inormation. You agree thatLinksys and/or its ailiates may, rom time to time, collectand process inormation about your Linksys product and/or the Sotware and/or your use o either in order (i) toenable Linksys to oer you Upgrades; (ii) to ensure that



36



your Linksys product and/or the Sotware is being used inaccordance with the terms o this Agreement; (iii) to provideimprovements to the way Linksys delivers technology toyou and to other Linksys customers; (iv) to enable Linksysto comply with the terms o any agreements it has withany third parties regarding your Linksys product and/or

Sotware and/or (v) to enable Linksys to comply with allapplicable laws and/or regulations, or the requirementso any regulatory authority or government agencyLinksys and/ or its ailiates may collect and processthis inormation provided that it does not identiy youpersonally Your use o your Linksys product and/or theSotware constitutes this consent by you to Linksys and/or its ailiates’ collection and use o such inormation and,or EEA customers, to the transer o such inormation to alocation outside the EEA

Sotware Upgrades etc. I the Sotware enables you toreceive Upgrades, you may elect at any time to receivethese Upgrades either automatically or manually I youelect to receive Upgrades manually or you otherwiseelect not to receive or be notiied o any Upgrades, youmay expose your Linksys product and/or the Sotwareto serious security threats and/or some eatures withinyour Linksys product and/or Sotware may becomeinaccessible There may be circumstances where weapply an Upgrade automatically in order to comply withchanges in legislation, legal or regulatory requirementsor as a result o requirements to comply with the termso any agreements Linksys has with any third partiesregarding your Linksys product and/or the Sotware Youwill always be notiied o any Upgrades being delivered

to you The terms o this license will apply to any suchUpgrade unless the Upgrade in question is accompaniedby a separate license, in which event the terms o thatlicense will apply

Open Source Sotware. The GPL or other open sourcecode incorporated into the Sotware and the open sourcelicense or such source code are available or ree downloadat http://www.linksys.com/gpl I You would like a copyo the GPL or other open source code in this Sotware on aCD, Linksys will mail to You a CD with such code or $999plus the cost o shipping, upon request

Term and Termination. You may terminate this License

at any time by destroying all copies o the Sotwareand documentation Your rights under this License willterminate immediately without notice rom Linksys i Youail to comply with any provision o this Agreement

Limited Warranty. The warranty terms and periodspeciied in the applicable Linksys Product User Guideshall also apply to the Sotware

Disclaimer o Liabilities. IN NO EVENT WILL LINKSYS ORITS SUPPLIERS BE LIABLE FOR ANY LOST DATA, REVENUEOR PROFIT, OR FOR SPECIAL, INDIRECT, CONSEQUENTIAL,INCIDENTAL OR PUNITIVE DAMAGES, REGARDLESS OFCAUSE (INCLUDING NEGLIGENCE), ARISING OUT OF

OR RELATED TO THE USE OF OR INABILITY TO USE THESOFTWARE, EVEN IF LINKSYS HAS BEEN ADVISED OFTHE POSSIBILITY OF SUCH DAMAGES IN NO EVENT WILLLINKSYS’ LIABILITY EXCEED THE AMOUNT PAID BY YOUFOR THE PRODUCT The oregoing limitations will applyeven i any warranty or remedy under this Agreement ails

o its essential purpose Some jurisdictions do not allowthe exclusion or limitation o incidental or consequentialdamages, so the above limitation or exclusion may notapply to You

Export. Sotware, including technical data, may be subjectto US export control laws and regulations and/or exportor import regulations in other countries You agree tocomply strictly with all such laws and regulations

U.S. Government Users. The Sotware and documentationqualiy as “commercial items” as deined at 48 CFR 2101and 48 CFR 12212 All Government users acquire theSotware and documentation with only those rights

herein that apply to non-governmental customersGeneral Terms. This Agreement will be governed by andconstrued in accordance with the laws o the State o Caliornia, without reerence to conlict o laws principlesThe United Nations Convention on Contracts or theInternational Sale o Goods will not apply I any portiono this Agreement is ound to be void or unenorceable,the remaining provisions will remain in ull orce andeect This Agreement constitutes the entire agreementbetween the parties with respect to the Sotware andsupersedes any conlicting or additional terms containedin any purchase order or elsewhere

END OF SCHEDULE 1

Schedule 2

I this Linksys product contains open source sotwarelicensed under Version 2 o the “GNU General PublicLicense” then the license terms below in this Schedule 2will apply to that open source sotware The license termsbelow in this Schedule 2 are rom the public web site athttp://www.gnu.org/copyleft/gpl.html

GNU GENERAL PUBLIC LICENSE

Version 2, June 1991

Copyright © 1989, 1991 Free Sotware Foundation, Inc

51 Franklin Street, Fith Floor, Boston, MA 02110-1301,USA

Everyone is permitted to copy and distribute verbatimcopies o this license document, but changing it is notallowed

Preamble

The licenses or most sotware are designed to take awayyour reedom to share and change it By contrast, the

http://www.gnu.org/copyleft/gpl.html

http://www.gnu.org/copyleft/gpl.html



37



GNU General Public License is intended to guarantee yourreedom to share and change ree sotware–to make surethe sotware is ree or all its users This General PublicLicense applies to most o the Free Sotware Foundation’ssotware and to any other program whose authorscommit to using it (Some other Free Sotware Foundation

sotware is covered by the GNU Lesser General PublicLicense instead) You can apply it to your programs, too

When we speak o ree sotware, we are reerring toreedom, not price Our General Public Licenses aredesigned to make sure that you have the reedom todistribute copies o ree sotware (and charge or thisservice i you wish), that you receive source code or canget it i you want it, that you can change the sotware oruse pieces o it in new ree programs; and that you knowyou can do these things

To protect your rights, we need to make restrictions thatorbid anyone to deny you these rights or to ask you to

surrender the rights These restrictions translate to certainresponsibilities or you i you distribute copies o thesotware, or i you modiy it

For example, i you distribute copies o such a program,whether gratis or or a ee, you must give the recipientsall the rights that you have You must make sure that they,too, receive or can get the source code And you mustshow them these terms so they know their rights

We protect your rights with two steps: (1) copyright thesotware, and (2) oer you this license which gives youlegal permission to copy, distribute and/or modiy thesotware

Also, or each author’s protection and ours, we want tomake certain that everyone understands that there is nowarranty or this ree sotware I the sotware is modiiedby someone else and passed on, we want its recipientsto know that what they have is not the original, so thatany problems introduced by others will not relect on theoriginal authors’ reputations

Finally, any ree program is threatened constantly bysotware patents We wish to avoid the danger thatredistributors o a ree program will individually obtainpatent licenses, in eect making the program proprietaryTo prevent this, we have made it clear that any patent must

be licensed or everyone’s ree use or not licensed at all

The precise terms and conditions or copying, distributionand modiication ollow

TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND

MODIFICATION

This License applies to any program or other work 0which contains a notice placed by the copyrightholder saying it may be distributed under the termso this General Public License The “Program”, below,reers to any such program or work, and a “work based on the Program” means either the Programor any derivative work under copyright law: that isto say, a work containing the Program or a portiono it, either verbatim or with modiications and/or translated into another language (Hereinater,translation is included without limitation in the term“modiication”) Each licensee is addressed as “you”

Activities other than copying, distribution andmodiication are not covered by this License; theyare outside its scope The act o running the Program

is not restricted, and the output rom the Program iscovered only i its contents constitute a work based onthe Program (independent o having been made byrunning the Program) Whether that is true dependson what the Program does

You may copy and distribute verbatim copies o the1Program’s source code as you receive it, in any medium,provided that you conspicuously and appropriatelypublish on each copy an appropriate copyrightnotice and disclaimer o warranty; keep intact all thenotices that reer to this License and to the absenceo any warranty; and give any other recipients o theProgram a copy o this License along with the Program

You may charge a ee or the physical act o transerringa copy, and you may at your option oer warrantyprotection in exchange or a ee

You may modiy your copy or copies o the Program2or any portion o it, thus orming a work based on theProgram, and copy and distribute such modiicationsor work under the terms o Section 1 above, providedthat you also meet all o these conditions:

You must cause the modiied iles to carryaprominent notices stating that you changed theiles and the date o any change

You must cause any work that you distribute orbpublish, that in whole or in part contains or isderived rom the Program or any part thereo, to belicensed as a whole at no charge to all third partiesunder the terms o this License



38



I the modiied program normally reads commandscinteractively when run, you must cause it, whenstarted running or such interactive use in the mostordinary way, to print or display an announcementincluding an appropriate copyright notice anda notice that there is no warranty (or else, saying

that you provide a warranty) and that users mayredistribute the program under these conditions,and telling the user how to view a copy o this License (Exception: i the Program itsel isinteractive but does not normally print such anannouncement, your work based on the Programis not required to print an announcement)

These requirements apply to the modiied work asa whole I identiiable sections o that work are notderived rom the Program, and can be reasonablyconsidered independent and separate works inthemselves, then this License, and its terms, do notapply to those sections when you distribute them asseparate works But when you distribute the samesections as part o a whole which is a work based onthe Program, the distribution o the whole must be onthe terms o this License, whose permissions or otherlicensees extend to the entire whole, and thus to eachand every part regardless o who wrote it

Thus, it is not the intent o this section to claim rightsor contest your rights to work written entirely by you;rather, the intent is to exercise the right to control thedistribution o derivative or collective works based onthe Program

In addition, mere aggregation o another work notbased on the Program with the Program (or with awork based on the Program) on a volume o a storageor distribution medium does not bring the other work under the scope o this License

You may copy and distribute the Program (or a3work based on it, under Section 2) in object code orexecutable orm under the terms o Sections 1 and 2above provided that you also do one o the ollowing:

Accompany it with the complete correspondingamachine-readable source code, which must bedistributed under the terms o Sections 1 and 2above on a medium customarily used or sotwareinterchange; or,

Accompany it with a written oer, valid or at leastbthree years, to give any third party, or a chargeno more than your cost o physically perormingsource distribution, a complete machine-readablecopy o the corresponding source code, to bedistributed under the terms o Sections 1 and 2above on a medium customarily used or sotwareinterchange; or,

Accompany it with the inormation you received ascto the oer to distribute corresponding source code(This alternative is allowed only or noncommercialdistribution and only i you received the programin object code or executable orm with such anoer, in accord with Subsection b above)

The source code or a work means the preerred ormo the work or making modiications to it For anexecutable work, complete source code means allthe source code or all modules it contains, plus anyassociated interace deinition iles, plus the scriptsused to control compilation and installation o theexecutable However, as a special exception, the sourcecode distributed need not include anything that isnormally distributed (in either source or binary orm)with the major components (compiler, kernel, and soon) o the operating system on which the executableruns, unless that component itsel accompanies theexecutable

I distribution o executable or object code is madeby oering access to copy rom a designated place,then oering equivalent access to copy the sourcecode rom the same place counts as distribution o the source code, even though third parties are notcompelled to copy the source along with the objectcode

You may not copy, modiy, sublicense, or distribute4the Program except as expressly provided underthis License Any attempt otherwise to copy, modiy,sublicense or distribute the Program is void, and willautomatically terminate your rights under this LicenseHowever, parties who have received copies, or rights,rom you under this License will not have their licensesterminated so long as such parties remain in ullcompliance

You are not required to accept this License, since you5have not signed it However, nothing else grants youpermission to modiy or distribute the Program or itsderivative works These actions are prohibited by law i you do not accept this License Thereore, by modiyingor distributing the Program (or any work based on theProgram), you indicate your acceptance o this Licenseto do so, and all its terms and conditions or copying,

distributing or modiying the Program or works basedon it

Each time you redistribute the Program (or any work 6based on the Program), the recipient automaticallyreceives a license rom the original licensor to copy,distribute or modiy the Program subject to theseterms and conditions You may not impose any urtherrestrictions on the recipients’ exercise o the rightsgranted herein You are not responsible or enorcingcompliance by third parties to this License



39



I, as a consequence o a court judgment or allegation7o patent inringement or or any other reason (notlimited to patent issues), conditions are imposed onyou (whether by court order, agreement or otherwise)that contradict the conditions o this License, they donot excuse you rom the conditions o this License I

you cannot distribute so as to satisy simultaneouslyyour obligations under this License and any otherpertinent obligations, then as a consequence youmay not distribute the Program at all For example,i a patent license would not permit royalty-reeredistribution o the Program by all those who receivecopies directly or indirectly through you, then the onlyway you could satisy both it and this License would beto rerain entirely rom distribution o the Program

I any portion o this section is held invalid orunenorceable under any particular circumstance,the balance o the section is intended to apply andthe section as a whole is intended to apply in other

circumstances

It is not the purpose o this section to induce you toinringe any patents or other property right claims orto contest validity o any such claims; this section hasthe sole purpose o protecting the integrity o the reesotware distribution system, which is implementedby public license practices Many people havemade generous contributions to the wide range o sotware distributed through that system in relianceon consistent application o that system; it is up tothe author/donor to decide i he or she is willing todistribute sotware through any other system and a

licensee cannot impose that choiceThis section is intended to make thoroughly clearwhat is believed to be a consequence o the rest o thisLicense

I the distribution and/or use o the Program is8restricted in certain countries either by patents or bycopyrighted interaces, the original copyright holderwho places the Program under this License may add anexplicit geographical distribution limitation excludingthose countries, so that distribution is permitted onlyin or among countries not thus excluded In such case,this License incorporates the limitation as i written in

the body o this LicenseThe Free Sotware Foundation may publish revised9and/or new versions o the General Public Licenserom time to time Such new versions will be similar inspirit to the present version, but may dier in detail toaddress new problems or concerns

Each version is given a distinguishing version numberI the Program speciies a version number o thisLicense which applies to it and “any later version”, youhave the option o ollowing the terms and conditionseither o that version or o any later version publishedby the Free Sotware Foundation I the Program does

not speciy a version number o this License, youmay choose any version ever published by the FreeSotware Foundation

I you wish to incorporate parts o the Program into10other ree programs whose distribution conditions aredierent, write to the author to ask or permission For

sotware which is copyrighted by the Free SotwareFoundation, write to the Free Sotware Foundation; wesometimes make exceptions or this Our decision willbe guided by the two goals o preserving the ree statuso all derivatives o our ree sotware and o promotingthe sharing and reuse o sotware generally

NO WARRANTY

BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE,11THERE IS NO WARRANTY FOR THE PROGRAM, TO THEEXTENT PERMITTED BY APPLICABLE LAW EXCEPTWHEN OTHERWISE STATED IN WRITING THE COPYRIGHT

HOLDERS AND/OR OTHER PARTIES PROVIDE THEPROGRAM “AS IS” WITHOUT WARRANTY OF ANYKIND, EITHER EXPRESSED OR IMPLIED, INCLUDING,BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OFMERCHANTABILITY AND FITNESS FOR A PARTICULARPURPOSE THE ENTIRE RISK AS TO THE QUALITY ANDPERFORMANCE OF THE PROGRAM IS WITH YOUSHOULD THE PROGRAM PROVE DEFECTIVE, YOUASSUME THE COST OF ALL NECESSARY SERVICING,REPAIR OR CORRECTION

IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR12AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER,OR ANY OTHER PARTY WHO MAY MODIFY AND/OR

REDISTRIBUTE THE PROGRAM AS PERMITTED ABOVE,BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANYGENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIALDAMAGES ARISING OUT OF THE USE OR INABILITY TOUSE THE PROGRAM (INCLUDING BUT NOT LIMITED TOLOSS OF DATA OR DATA BEING RENDERED INACCURATEOR LOSSES SUSTAINED BY YOU OR THIRD PARTIES ORA FAILURE OF THE PROGRAM TO OPERATE WITH ANYOTHER PROGRAMS), EVEN IF SUCH HOLDER OR OTHERPARTY HAS BEEN ADVISED OF THE POSSIBILITY OFSUCH DAMAGES

END OF TERMS AND CONDITIONS

END OF SCHEDULE 2

Schedule 3

I this Linksys product contains open source sotwarelicensed under Version 21 o the“GNU Lesser General PublicLicense” then the license terms below in this Schedule 3will apply to that open source sotware The license termsbelow in this Schedule 3 are rom the public web site athttp://www.gnu.org/licenses/old-licenses/lgpl-2.1.html



40



GNU LESSER GENERAL PUBLIC LICENSE

Version 21, February 1999

Copyright (C) 1991, 1999 Free Sotware Foundation, Inc

51 Franklin Street, Fith Floor, Boston, MA 02110-1301,USA

Everyone is permitted to copy and distribute verbatimcopies o this license document, but changing it is notallowed

[This is the irst released version o the Lesser GPL It alsocounts as the successor o the GNU Library Public License,version 2, hence the version number 21]

Preamble

The licenses or most sotware are designed to take awayyour reedom to share and change it By contrast, the GNUGeneral Public Licenses are intended to guarantee your

reedom to share and change ree sotware—to makesure the sotware is ree or all its users

This license, the Lesser General Public License, applies tosome specially designated sotware packages—typicallylibraries—o the Free Sotware Foundation and otherauthors who decide to use it You can use it too, but wesuggest you irst think careully about whether this licenseor the ordinary General Public License is the better strategyto use in any particular case, based on the explanationsbelow

When we speak o ree sotware, we are reerring toreedom o use, not price Our General Public Licenses

are designed to make sure that you have the reedomto distribute copies o ree sotware (and charge or thisservice i you wish); that you receive source code or canget it i you want it; that you can change the sotware anduse pieces o it in new ree programs; and that you areinormed that you can do these things

To protect your rights, we need to make restrictions thatorbid distributors to deny you these rights or to ask youto surrender these rights These restrictions translate tocertain responsibilities or you i you distribute copies o the library or i you modiy it

For example, i you distribute copies o the library,

whether gratis or or a ee, you must give the recipientsall the rights that we gave you You must make sure thatthey, too, receive or can get the source code I you link other code with the library, you must provide completeobject iles to the recipients, so that they can relink themwith the library ater making changes to the library andrecompiling it And you must show them these terms sothey know their rights

We protect your rights with a two-step method: (1) wecopyright the library, and (2) we oer you this license,which gives you legal permission to copy, distribute and/or modiy the library

To protect each distributor, we want to make it very clearthat there is no warranty or the ree library Also, i thelibrary is modiied by someone else and passed on, therecipients should know that what they have is not theoriginal version, so that the original author’s reputationwill not be aected by problems that might be introduced

by othersFinally, sotware patents pose a constant threat to theexistence o any ree program We wish to make surethat a company cannot eectively restrict the users o a ree program by obtaining a restrictive license rom apatent holder Thereore, we insist that any patent licenseobtained or a version o the library must be consistentwith the ull reedom o use speciied in this license

Most GNU sotware, including some libraries, is coveredby the ordinary GNU General Public License This license,the GNU Lesser General Public License, applies to certaindesignated libraries, and is quite dierent rom the

ordinary General Public License We use this license orcertain libraries in order to permit linking those librariesinto non-ree programs

When a program is linked with a library, whetherstatically or using a shared library, the combination o the two is legally speaking a combined work, a derivativeo the original library The ordinary General PublicLicense thereore permits such linking only i the entirecombination its its criteria o reedom The Lesser GeneralPublic License permits more lax criteria or linking othercode with the library

We call this license the “Lesser” General Public License

because it does Less to protect the user’s reedom thanthe ordinary General Public License It also providesother ree sotware developers Less o an advantage overcompeting non-ree programs These disadvantages arethe reason we use the ordinary General Public Licenseor many libraries However, the Lesser license providesadvantages in certain special circumstances

For example, on rare occasions, there may be a specialneed to encourage the widest possible use o a certainlibrary, so that it becomes a de-acto standard To achievethis, non-ree programs must be allowed to use the libraryA more requent case is that a ree library does the same

job as widely used non-ree libraries In this case, there islittle to gain by limiting the ree library to ree sotwareonly, so we use the Lesser General Public License

In other cases, permission to use a particular library in non-ree programs enables a greater number o people to usea large body o ree sotware For example, permission touse the GNU C Library in non-ree programs enables manymore people to use the whole GNU operating system, aswell as its variant, the GNU/Linux operating system

Although the Lesser General Public License is Lessprotective o the users’ reedom, it does ensure that theuser o a program that is linked with the Library has the



41



reedom and the wherewithal to run that program using amodiied version o the Library

The precise terms and conditions or copying, distributionand modiication ollow Pay close attention to thedierence between a “work based on the library” and a“work that uses the library” The ormer contains code

derived rom the library, whereas the latter must becombined with the library in order to run

GNU LESSER GENERAL PUBLIC LICENSE

TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND

MODIFICATION

This License Agreement applies to any sotware library0or other program which contains a notice placed bythe copyright holder or other authorized party sayingit may be distributed under the terms o this LesserGeneral Public License (also called “this License”) Each

licensee is addressed as “you”A “library” means a collection o sotware unctionsand/or data prepared so as to be conveniently linkedwith application programs (which use some o thoseunctions and data) to orm executables

The “Library”, below, reers to any such sotware libraryor work which has been distributed under these termsA “work based on the Library” means either the Libraryor any derivative work under copyright law: that is tosay, a work containing the Library or a portion o it,either verbatim or with modiications and/or translatedstraightorwardly into another language (Hereinater,

translation is included without limitation in the term“modiication”)

“Source code” or a work means the preerred orm o the work or making modiications to it For a library,complete source code means all the source code orall modules it contains, plus any associated interacedeinition iles, plus the scripts used to controlcompilation and installation o the library

Activities other than copying, distribution andmodiication are not covered by this License; they areoutside its scope The act o running a program usingthe Library is not restricted, and output rom such a

program is covered only i its contents constitute awork based on the Library (independent o the useo the Library in a tool or writing it) Whether that istrue depends on what the Library does and what theprogram that uses the Library does

You may copy and distribute verbatim copies o the1Library’s complete source code as you receive it, inany medium, provided that you conspicuously andappropriately publish on each copy an appropriatecopyright notice and disclaimer o warranty; keepintact all the notices that reer to this License and to

the absence o any warranty; and distribute a copy o this License along with the Library

You may charge a ee or the physical act o transerringa copy, and you may at your option oer warrantyprotection in exchange or a ee

You may modiy your copy or copies o the Library or2any portion o it, thus orming a work based on theLibrary, and copy and distribute such modiicationsor work under the terms o Section 1 above, providedthat you also meet all o these conditions:

The modiied work must itsel be a sotwarea)library

You must cause the iles modiied to carryb)prominent notices stating that you changed theiles and the date o any change

You must cause the whole o the work to bec)licensed at no charge to all third parties under theterms o this License

I a acility in the modiied Library reers to a unctiond)or a table o data to be supplied by an applicationprogram that uses the acility, other than as anargument passed when the acility is invoked, thenyou must make a good aith eort to ensure that,

in the event an application does not supply suchunction or table, the acility still operates, andperorms whatever part o its purpose remainsmeaningul

(For example, a unction in a library to computesquare roots has a purpose that is entirely well-deined independent o the application Thereore,Subsection 2d requires that any application-supplied unction or table used by this unctionmust be optional: i the application does not supplyit, the square root unction must still computesquare roots)

These requirements apply to the modiied work asa whole I identiiable sections o that work are notderived rom the Library, and can be reasonablyconsidered independent and separate works inthemselves, then this License, and its terms, donot apply to those sections when you distributethem as separate works But when you distributethe same sections as part o a whole which is awork based on the Library, the distribution o thewhole must be on the terms o this License, whosepermissions or other licensees extend to the entirewhole, and thus to each and every part regardlesso who wrote it



42



Thus, it is not the intent o this section to claimrights or contest your rights to work written entirelyby you; rather, the intent is to exercise the right tocontrol the distribution o derivative or collectiveworks based on the Library

In addition, mere aggregation o another work

not based on the Library with the Library (or witha work based on the Library) on a volume o astorage or distribution medium does not bring theother work under the scope o this License

You may opt to apply the terms o the ordinary GNU3General Public License instead o this License to agiven copy o the Library To do this, you must alter allthe notices that reer to this License, so that they reerto the ordinary GNU General Public License, version2, instead o to this License (I a newer version thanversion 2 o the ordinary GNU General Public Licensehas appeared, then you can speciy that version

instead i you wish) Do not make any other change inthese notices

Once this change is made in a given copy, it isirreversible or that copy, so the ordinary GNU GeneralPublic License applies to all subsequent copies andderivative works made rom that copy

This option is useul when you wish to copy part o thecode o the Library into a program that is not a library

You may copy and distribute the Library (or a portion4or derivative o it, under Section 2) in object code orexecutable orm under the terms o Sections 1 and2 above provided that you accompany it with the

complete corresponding machine-readable sourcecode, which must be distributed under the terms o Sections 1 and 2 above on a medium customarily usedor sotware interchange

I distribution o object code is made by oeringaccess to copy rom a designated place, then oeringequivalent access to copy the source code rom thesame place satisies the requirement to distributethe source code, even though third parties are notcompelled to copy the source along with the objectcode

A program that contains no derivative o any portion5

o the Library, but is designed to work with the Libraryby being compiled or linked with it, is called a “work that uses the Library” Such a work, in isolation, is nota derivative work o the Library, and thereore allsoutside the scope o this License

However, linking a “work that uses the Library” withthe Library creates an executable that is a derivativeo the Library (because it contains portions o theLibrary), rather than a “work that uses the library” Theexecutable is thereore covered by this License Section6 states terms or distribution o such executables

When a “work that uses the Library” uses material roma header ile that is part o the Library, the object codeor the work may be a derivative work o the Libraryeven though the source code is not Whether this istrue is especially signiicant i the work can be linkedwithout the Library, or i the work is itsel a library The

threshold or this to be true is not precisely deined bylaw

I such an object ile uses only numerical parameters,data structure layouts and accessors, and small macrosand small inline unctions (ten lines or less in length),then the use o the object ile is unrestricted, regardlesso whether it is legally a derivative work (Executablescontaining this object code plus portions o the Librarywill still all under Section 6)

Otherwise, i the work is a derivative o the Library, youmay distribute the object code or the work under theterms o Section 6 Any executables containing that

work also all under Section 6, whether or not they arelinked directly with the Library itsel

As an exception to the Sections above, you may also6combine or link a “work that uses the Library” with theLibrary to produce a work containing portions o theLibrary, and distribute that work under terms o yourchoice, provided that the terms permit modiicationo the work or the customer’s own use and reverseengineering or debugging such modiications

You must give prominent notice with each copy o the work that the Library is used in it and that theLibrary and its use are covered by this License You

must supply a copy o this License I the work duringexecution displays copyright notices, you must includethe copyright notice or the Library among them, aswell as a reerence directing the user to the copy o thisLicense Also, you must do one o these things:

Accompany the work with the completea)corresponding machine-readable source codeor the Library including whatever changes wereused in the work (which must be distributedunder Sections 1 and 2 above); and, i the work is an executable linked with the Library, with thecomplete machine-readable “work that uses theLibrary”, as object code and/or source code, so thatthe user can modiy the Library and then relink to produce a modiied executable containing themodiied Library (It is understood that the userwho changes the contents o deinitions iles in theLibrary will not necessarily be able to recompile theapplication to use the modiied deinitions)



43



Use a suitable shared library mechanism or linkingb)with the Library A suitable mechanism is one that(1) uses at run time a copy o the library alreadypresent on the user ’s computer system, rather thancopying library unctions into the executable, and(2) will operate properly with a modiied version o

the library, i the user installs one, as long as themodiied version is interace-compatible with theversion that the work was made with

Accompany the work with a written oer, validc)or at least three years, to give the same user thematerials speciied in Subsection 6a, above, or acharge no more than the cost o perorming thisdistribution

I distribution o the work is made by oering accessd)to copy rom a designated place, oer equivalentaccess to copy the above speciied materials romthe same place

Veriy that the user has already received a copy o e)these materials or that you have already sent thisuser a copy

For an executable, the required orm o the “work thatuses the Library” must include any data and utilityprograms needed or reproducing the executable romit However, as a special exception, the materials to bedistributed need not include anything that is normallydistributed (in either source or binary orm) with themajor components (compiler, kernel, and so on) o theoperating system on which the executable runs, unlessthat component itsel accompanies the executable

It may happen that this requirement contradicts thelicense restrictions o other proprietary libraries thatdo not normally accompany the operating systemSuch a contradiction means you cannot use boththem and the Library together in an executable thatyou distribute

You may place library acilities that are a work based7on the Library side-by-side in a single library togetherwith other library acilities not covered by this License,and distribute such a combined library, provided thatthe separate distribution o the work based on theLibrary and o the other library acilities is otherwise

permitted, and provided that you do these twothings:

Accompany the combined library with a copy o thea)same work based on the Library, uncombined withany other library acilities This must be distributedunder the terms o the Sections above

Give prominent notice with the combined library o b)the act that part o it is a work based on the Library,and explaining where to ind the accompanyinguncombined orm o the same work

You may not copy, modiy, sublicense, link with, or8distribute the Library except as expressly providedunder this License Any attempt otherwise to copy,modiy, sublicense, link with, or distribute the Libraryis void, and will automatically terminate your rightsunder this License However, parties who have received

copies, or rights, rom you under this License will nothave their licenses terminated so long as such partiesremain in ull compliance

You are not required to accept this License, since you9have not signed it However, nothing else grants youpermission to modiy or distribute the Library or itsderivative works These actions are prohibited by law i you do not accept this License Thereore, by modiyingor distributing the Library (or any work based on theLibrary), you indicate your acceptance o this Licenseto do so, and all its terms and conditions or copying,distributing or modiying the Library or works basedon it

Each time you redistribute the Library (or any work 10based on the Library), the recipient automaticallyreceives a license rom the original licensor to copy,distribute, link with or modiy the Library subjectto these terms and conditions You may not imposeany urther restrictions on the recipients’ exercise o the rights granted herein You are not responsibleor enorcing compliance by third parties with thisLicense

I, as a consequence o a court judgment or allegation11o patent inringement or or any other reason (notlimited to patent issues), conditions are imposed on

you (whether by court order, agreement or otherwise)that contradict the conditions o this License, they donot excuse you rom the conditions o this License I you cannot distribute so as to satisy simultaneouslyyour obligations under this License and any otherpertinent obligations, then as a consequence you maynot distribute the Library at all For example, i a patentlicense would not permit royalty-ree redistribution o the Library by all those who receive copies directly orindirectly through you, then the only way you couldsatisy both it and this License would be to rerainentirely rom distribution o the Library

I any portion o this section is held invalid orunenorceable under any particular circumstance,the balance o the section is intended to apply, andthe section as a whole is intended to apply in othercircumstances

It is not the purpose o this section to induce you toinringe any patents or other property right claims orto contest validity o any such claims; this section hasthe sole purpose o protecting the integrity o the reesotware distribution system which is implementedby public license practices Many people havemade generous contributions to the wide range o



44



sotware distributed through that system in relianceon consistent application o that system; it is up tothe author/donor to decide i he or she is willing todistribute sotware through any other system and alicensee cannot impose that choice

This section is intended to make thoroughly clear

what is believed to be a consequence o the rest o thisLicense

I the distribution and/or use o the Library is restricted12in certain countries either by patents or by copyrightedinteraces, the original copyright holder who placesthe Library under this License may add an explicitgeographical distribution limitation excluding thosecountries, so that distribution is permitted only in oramong countries not thus excluded In such case, thisLicense incorporates the limitation as i written in thebody o this License

The Free Sotware Foundation may publish revised13

and/or new versions o the Lesser General PublicLicense rom time to time Such new versions will besimilar in spirit to the present version, but may dier indetail to address new problems or concerns

Each version is given a distinguishing version numberI the Library speciies a version number o this Licensewhich applies to it and “any later version”, you have theoption o ollowing the terms and conditions either o that version or o any later version published by the FreeSotware Foundation I the Library does not speciy alicense version number, you may choose any versionever published by the Free Sotware Foundation

I you wish to incorporate parts o the Library into14other ree programs whose distribution conditions areincompatible with these, write to the author to ask orpermission For sotware which is copyrighted by theFree Sotware Foundation, write to the Free SotwareFoundation; we sometimes make exceptions orthis Our decision will be guided by the two goals o preserving the ree status o all derivatives o our reesotware and o promoting the sharing and reuse o sotware generally

NO WARRANTY

BECAUSE THE LIBRARY IS LICENSED FREE OF CHARGE,15THERE IS NO WARRANTY FOR THE LIBRARY, TO THEEXTENT PERMITTED BY APPLICABLE LAW EXCEPTWHEN OTHERWISE STATED IN WRITING THE COPYRIGHTHOLDERS AND/OR OTHER PARTIES PROVIDE THELIBRARY “AS IS” WITHOUT WARRANTY OF ANY KIND,

EITHER EXPRESSED OR IMPLIED, INCLUDING, BUTNOT LIMITED TO, THE IMPLIED WARRANTIES OFMERCHANTABILITY AND FITNESS FOR A PARTICULARPURPOSE THE ENTIRE RISK AS TO THE QUALITY ANDPERFORMANCE OF THE LIBRARY IS WITH YOU SHOULDTHE LIBRARY PROVE DEFECTIVE, YOU ASSUME THECOST OF ALL NECESSARY SERVICING, REPAIR ORCORRECTION

IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW16OR AGREED TO IN WRITING WILL ANY COPYRIGHTHOLDER, OR ANY OTHER PARTY WHO MAY MODIFYAND/OR REDISTRIBUTE THE LIBRARY AS PERMITTEDABOVE, BE LIABLE TO YOU FOR DAMAGES,

INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL ORCONSEQUENTIAL DAMAGES ARISING OUT OF THEUSE OR INABILITY TO USE THE LIBRARY (INCLUDINGBUT NOT LIMITED TO LOSS OF DATA OR DATA BEINGRENDERED INACCURATE OR LOSSES SUSTAINED BYYOU OR THIRD PARTIES OR A FAILURE OF THE LIBRARYTO OPERATE WITH ANY OTHER SOFTWARE), EVEN IFSUCH HOLDER OR OTHER PARTY HAS BEEN ADVISEDOF THE POSSIBILITY OF SUCH DAMAGES

END OF TERMS AND CONDITIONS

END OF SCHEDULE 3

Schedule 4I this Linksys product contains open source sotwarelicensed under the OpenSSL license:

This product includes sotware developed by theOpenSSL Project or use in the OpenSSL Toolkit(http://www.openssl.org/)

This product includes cryptographic sotware written byEric Young (eay@cryptsotcom)

This product includes sotware written by Tim Hudson(tjh@cryptsotcom)

In addition, i this Linksys product contains opensource sotware licensed under the OpenSSL licensethen the license terms below in this Schedule 3 willapply to that open source sotware The license termsbelow in this Schedule 3 are rom the public web site athttp://www.openssl.org/source/license.html

The OpenSSL toolkit stays under a dual license, ie boththe conditions o the OpenSSL License and the originalSSLeay license apply to the toolkit See below or theactual license texts Actually both licenses are BSD-styleOpen Source licenses In case o any license issues relatedto OpenSSL please contact openssl-core@opensslorg

http://www.openssl.org/

http://www.openssl.org/source/license.html

http://www.openssl.org/source/license.html




45



OpenSSL License

Copyright © 1998-2007 The OpenSSL Project All rightsreserved

Redistribution and use in source and binary orms, withor without modiication, are permitted provided that the

ollowing conditions are met:Redistributions o source code must retain the above1copyright notice, this list o conditions and theollowing disclaimer

Redistributions in binary orm must reproduce the2above copyright notice, this list o conditions and theollowing disclaimer in the documentation and/orother materials provided with the distribution

All advertising materials mentioning eatures or3use o this sotware must display the ollowingacknowledgment: “This product includes sotwaredeveloped by the OpenSSL Project or use in the

OpenSSL Toolkit (http://www.openssl.org/)”

The names “OpenSSL Toolkit” and “OpenSSL Project”4must not be used to endorse or promote productsderived rom this sotware without prior writtenpermission For written permission, please contactopenssl-core@opensslorg

Products derived rom this sotware may not be called5“OpenSSL” nor may “OpenSSL” appear in their nameswithout prior written permission o the OpenSSLProject

Redistributions o any orm whatsoever must retain6the ollowing acknowledgment: “This product includessotware developed by the OpenSSL Project or use inthe OpenSSL Toolkit (http://www.openssl.org/)”

THIS SOFTWARE IS PROVIDED BY THE OpenSSL PROJECT“AS IS” AND ANY EXPRESSED OR IMPLIED WARRANTIES,INCLUDING, BUT NOT LIMITED TO, THE IMPLIEDWARRANTIES OF MERCHANTABILITY AND FITNESS FORA PARTICULAR PURPOSE ARE DISCLAIMED IN NO EVENTSHALL THE OpenSSL PROJECT OR ITS CONTRIBUTORS BELIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTEGOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS;

OR BUSINESS INTERRUPTION) HOWEVER CAUSED ANDON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OROTHERWISE) ARISING IN ANY WAY OUT OF THE USE OFTHIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OFSUCH DAMAGE

This product includes cryptographic sotware written byEric Young (eay@cryptsotcom) This product includessotware written by Tim Hudson (tjh@cryptsotcom)

Original SSLeay License

Copyright © 1995-1998 Eric Young (eay@cryptsotcom)Allrights reserved

This package is an SSL implementation written by EricYoung (eay@cryptsotcom)

The implementation was written so as to conorm withNetscape’s SSL

This library is ree or commercial and non-commercialuse as long as the ollowing conditions are adhered toThe ollowing conditions apply to all code ound in thisdistribution, be it the RC4, RSA, lhash, DES, etc, code; not

just the SSL code The SSL documentation included withthis distribution is covered by the same copyright termsexcept that the holder is Tim Hudson (tjh@cryptsotcom)

Copyright remains Eric Young’s, and as such any Copyrightnotices in the code are not to be removed

I this package is used in a product, Eric Young should begiven attribution as the author o the parts o the libraryused This can be in the orm o a textual message atprogram startup or in documentation (online or textual)provided with the package

Redistribution and use in source and binary orms, withor without modiication, are permitted provided that theollowing conditions are met:

Redistributions o source code must retain the1copyright notice, this list o conditions and theollowing disclaimer

Redistributions in binary orm must reproduce the2above copyright notice, this list o conditions and theollowing disclaimer in the documentation and/orother materials provided with the distribution

All advertising materials mentioning eatures or3use o this sotware must display the ollowingacknowledgement:

“This product includes cryptographic sotware writtenby Eric Young (eay@cryptsotcom)”

The word ‘cryptographic’ can be let out i the routinesrom the library being used are not cryptographic

relatedI you include any Windows speciic code (or a derivative4thereo) rom the apps directory (application code)you must include an acknowledgement: “This productincludes sotware written by Tim Hudson (tjh@cryptsotcom)”

THIS SOFTWARE IS PROVIDED BY ERIC YOUNG “AS IS” ANDANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING,BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OFMERCHANTABILITY AND FITNESS FOR A PARTICULARPURPOSE ARE DISCLAIMED IN NO EVENT SHALL THEAUTHOR OR CONTRIBUTORS BE LIABLE FOR ANY








DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY,OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOTLIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS ORSERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESSINTERRUPTION) HOWEVER CAUSED AND ON ANY THEORYOF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,

OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE

The license and distribution terms or any publicly availableversion or derivative o this code cannot be changed iethis code cannot simply be copied and put under anotherdistribution license [including the GNU Public License]

END OF SCHEDULE 4

Date post:	07-Apr-2018
Category:	Documents
Upload:	bharti
View:	213 times
Download:	0 times