37 www.westernfilter.com
TMIN-TANK FILTERSSeries WT15 100 PSI
Replacement elementsare available in R-PakTM
and P-PakTM
Availablewith reservoir mounting weldring
Wide choice ofgauges andswitches
Easy to serviceslotted cover
WT1520 gpm (76 l/min)
FEATURES
The compact WT15 in-tank filter provides a spacesaving solution to spin-on filters. Service elementsare offered in glass and cellulose media. The bypassvalve is integral with the element. An optional weldring provides an easy solution to insure a positiveseal between housing and reservoir. Four standardgrades of media are offered down to 5.1µ(c).
Western Filter elements are compatible withpetroleum oils, water glycol, oil/water, HWCF andsynthetic fluids.
Technical Data:
Maximum Working Pressure 100 psi (7 bar)
Rated Burst Pressure 250 psi max(17.2 bar)
Temperature Range Operating Buna N -45ºF to + 225ºF
(-45ºC to + 107ºC)Viton -20ºF to + 250ºF
(-29ºC to + 121ºC)
Head and Cover Material Aluminum
Canister Material Steel
WeightAssembly 2.35 lbs. (1,1 kg.)
ACCESSORIES
Seal Kit -Buna N
Seal Kit -Viton
Weld Ring
P-233054-01
P-233054-03
P-233637
www.westernfilter.com 38
TMIN-TANK FILTERSSeries WT15 100 PSI
Housing and Filter ElementFlow versus Pressure Drop150 SUS (32 cSt.) oil with specific gravity < 0.9
MED
IUM
PRES
SUR
ESP
IN-O
NFI
LTER
SLO
WPR
ESSU
RE
SPIN
-ON
FILT
ERS
IN-T
AN
KFI
LTER
SLO
WPR
ESSU
REFI
LTER
SM
EDIU
MPR
ESSU
REFI
LTER
SH
IGH
PRES
SURE
FILT
ERS
40
C05
GPM
ET15
PSID
8 12 16
C10
C03
C20
0
4
8
16
12
20
50
GPM
10 15 20
PSID
0
2
4
6
8Housing Only
25 30
50
GPM
10 15 20
PSID
0
3
6
12
9
ET15
P10
P20
Viscosity Correction Formula∆P Element = psid from catalog X New Viscosity (SUS) X New Specific Gravity
150 0.90∆P Housing = psid from catalog X New Specific Gravity
0.90∆P Assembly = ∆P Element + ∆P Housing
39 www.westernfilter.com
TMIN-TANK FILTERSSeries WT15 200 PSI
Table 1Filter Assembly / Service Element
CODE DESCRIPTION
WT15 Assembly
ET15 Element
Table 2Element Collapse Options
CODE DESCRIPTION
1 150 psid
Table 3Port Size Options
CODE PORT SIZE
A 1-1/16” - 12 UN (SAE-12)
Table 4Bypass Setting Options
CODE BYPASS SETTING
3 25 psid
Table 7Assembly & Element Length
CODE (LGTH) CANISTER LENGTH
1 (8.49”) 5”
Table 8Element Code
CODE DESCRIPTION
C (Glass) 03, 05, 10, 20
P (Cellulose) 10, 20
Table 9Media Rating
CODE TARGET FLUID CLEANLINESS LEVEL
03 16/14/12 or better
05 18/16/14 or better
10 20/18/15 or better
20 22/19/16 or better
Note: Information concerning fluidcleanliness codes is on page 6, theMedia Grade Selection Guide.
Filter Assembly
Service Element
WT15 1 A 3 4 V 1 C 10
ET15 1 V 1 C 10
TABLE 1 TABLE 2 TABLE 3 TABLE 4 TABLE 5 TABLE 6 TABLE 7 TABLE 8 TABLE 9
TABLE 1 TABLE 2 TABLE 6 TABLE 7 TABLE 8 TABLE 9
Table 5Upstream Pressure Gauge andSwitch Option
CODE INDICATOR STYLE & SETTING
1 Gauge ports drilled, tapped and plugged
4 0-60 psi pressure gauge*6 Pressure switch 18 psi
Brad Harrison (5-pin)8 Pressure switch 18 psi
Hirschmann (4-pin)
Table 6Seal Options
CODE MATERIAL
B Buna N
V Viton
www.westernfilter.com 40
TMIN-TANK FILTERSSeries WT15 200 PSI
67.00(2.64)
136.14(5.36)
69.60(2.74)
9.38(.37)
27.74(1.09)
215.65(8.49)
189.23(7.45)
27.94(1.10)
87.88(3.46)
78.99(3.11)
1/8" NPT(Gauge Port, Plugged)
8.90 (.35) Located on 119.40 (4.70) BC 2 Plcs.
145.29(5.72)
Inlet Port
Outlet To Tank
Dimensions: millimeters/(inches)
MED
IUM
PRES
SUR
ESP
IN-O
NFI
LTER
SLO
WPR
ESSU
RE
SPIN
-ON
FILT
ERS
IN-T
AN
KFI
LTER
SLO
WPR
ESSU
REFI
LTER
SM
EDIU
MPR
ESSU
REFI
LTER
SH
IGH
PRES
SURE
FILT
ERS
41 www.westernfilter.com
IN-TANK FILTERSSeries WL16 200 PSI
Conforms to HF4automotive specifications
Available with reservoirmounting weld ring
Replacement elements areavailable in C-PakTM, E-PakTM,W-PakTM, and Z-PakTM
Dual pressure gauge ports
Optional second inlet port
Optional check valve
Easy to service slotted cover
WL16150 gpm (568 l/min)
FEATURES
WL16 in-tank meets the HF4 automotive standard.The E4051 service elements interchange withSchroeder K series and Zinga RE-409 series. Anoptional weld ring provides an easy solution toinsure a positive seal between housing and reservoir.The quick disconnect cover facilitates for easy andefficient element change-outs. An optional secondaryinlet port offers the use of a second return line. Theseunits can be top or side reservoir mounted. Use theoptional anti-backflow valve when installing thisfilter assembly to side of reservoir. Five standardgrades of media are offered down to 4.0µ(c). Z-Pac™stainless steel media is also available.
Western Filter elements are compatible withpetroleum oils, water glycol, oil/water, HWCF andsynthetic fluids.
Options and configurations formerly offered in ourWL15 Series have now been integrated into ourWL16 Series as indicated on the following pages(Code length 3 and 9 with optional extension tube).
Technical Data:
Maximum Working Pressure 200 psi (14 bar)
Rated Burst Pressure 300 psi max(21 bar)
Temperature Range Operating Buna N -45ºF to + 225ºF
(-45ºC to + 107ºC)Viton -20ºF to + 250ºF
(-29ºC to + 121ºC)
Head and Cover Material Aluminum
Canister Material Steel
WeightAssembly length 3 5.25 lbs. (2,3 kg.)Assembly length 6 16 lbs. (7,3 kg.)Assembly length 7 23 lbs. (10 kg.)Assembly length 9 6.25 lbs. (2,8 kg.)
ACCESSORIES
Seal Kit - Buna N
Seal Kit - E.P.R.
Seal Kit - Viton
Outlet Check Valve
Outlet Diffusor
Core tube assembly-Code length 3 & 9
Core tube assembly-Code length 6
Core tube assembly-Code length 7
P-233055-01
P-233055-02
P-232964-03
P-137457
P-239290
PW451R3BN
PW451R6BN
PW451R7BN
TM
www.westernfilter.com 42
IN-TANK FILTERSSeries WL16 200 PSI
Housing and Filter ElementFlow versus Pressure Drop150 SUS (32 cSt.) oil with specific gravity < 0.9
MED
IUM
PRES
SUR
ESP
IN-O
NFI
LTER
SLO
WPR
ESSU
RE
SPIN
-ON
FILT
ERS
IN-T
AN
KFI
LTER
SLO
WPR
ESSU
REFI
LTER
SM
EDIU
MPR
ESSU
REFI
LTER
SH
IGH
PRES
SURE
FILT
ERS
400
GPM
80 120 160
PSID
0
3
6
9
12
15Housing Only
2
4
6
8
10
12
PSID
GPM
00
20 40 60 80 100
P10
P20
E405 - 18”
3
6
9
12
15
PSID
GPM
00
25 50 75 100 125
P10P20
E405 - 27”
150
0
20
40
60
0 50GPM
PSID
Bypass Valve
100 150
50 PSID cracking
25 PSID cracking
80
100
3
6
9
12
15
PSID
GPM
00
25 50 75 100 125
E405 - 27”
150
C/E03
C/E10C/E05
C/E01
C20
4
8
12
16
PSID
GPM
00
20 40 60 80 100
C/E03
C/E10C/E05
C/E01
C20
E405 - 18”
1
2
3
4
5
PSID
GPM
00
10 20 30 40 50
E405 - 9”
4
8
12
16
PSID
GPM
00
10 20 30 40 50
E405 - 9”
C/E03
C/E10C/E05
C20
Viscosity Correction Formula∆P Element = psid from catalog X New Viscosity (SUS) X New Specific Gravity
150 0.90∆P Housing = psid from catalog X New Specific Gravity
0.90∆P Assembly = ∆P Element + ∆P Housing
TM
43 www.westernfilter.com
TMIN-TANK FILTERSSeries WL16 200 PSI
Table 1Filter Assembly / Service Element
CODE DESCRIPTION
WL16 Assembly
E405 Element
Table 2Element Collapse Options
CODE DESCRIPTION
1 150 psid
Table 3Port Size Options
CODE PORT SIZE
D 1-7/8” - 12 UN (SAE-24)E 1-1/2” SAE 4 Bolt Flange
Code 61U 1-1/2” NPT
Table 4Bypass Setting Options
CODE BYPASS SETTING
3 25 psid
4 50 psid
Table 6Assembly & Element Length
CODE (LGTH) ELEMENT LENGTH
3 (12.76”) 9”
6 (16.94”) 18”
7 (26.31”) 27”
9 (24.88”)* 9”*With 12” extension tube.
Note: Code length 6, 7 & 9 may be stacked using connector part # P-227567-01 and code length 3 elements
Table 10Media Rating
CODE TARGET FLUID CLEANLINESS LEVEL
01 Flushing only
03 16/14/12 or better
05 18/16/14 or better
10 20/18/15 or better
20 22/19/16 or better
Note: Information concerning fluidcleanliness codes is on page 6, theMedia Grade Selection Guide.
Metric Porting AvailableChange WL16 to GL16Porting code D becomes 1-1/2” ISO 223 BSPPPorting code E becomes 1-1/2” SAE 4 bolt flange with M12 threads
Filter Assembly
Service Element
WL16 1 D 4 2 6 N B C
E405 1 B 6 C 10
TABLE 1 TABLE 2 TABLE 3 TABLE 4 TABLE 5 TABLE 6 TABLE 7 TABLE 8 TABLE 9
TABLE 1 TABLE 2 TABLE 8 TABLE 6 TABLE 9 TABLE 10
Table 5Upstream Pressure Gauge andSwitch Option
CODE INDICATOR STYLE & SETTING
1 No indicator2 0-200 psi pressure gauge**3 0-60 psi pressure gauge**4 0-60 psi pressure gauge*6 Pressure switch 18 psi
Brad Harrison (5-pin)7 Pressure switch 35 psi
Brad Harrison (5-pin)8 Pressure switch 18 psi
Hirschmann (4-pin)9 Pressure switch 35 psi
Hirschmann (4-pin)*Bypass setting option code 3 only
**Bypass setting option code 4 only
10TABLE 10
Table 7Secondary Port Options
CODE PORT SIZE
T 1-7/8” - 12 UN (SAE-24)Z 1-1/2” SAE 4 Bolt Flange
Code 61N NoneV 1-1/2” NPT
Table 8Seal Options
CODE MATERIAL
B Buna N
E E.P.R.
V Viton
Table 9Element Code
CODE DESCRIPTION
C (Glass) 01, 03, 05, 10, 20
E (Coreless) 01, 03, 05, 10
P (Cellulose) 10, 20
W (Water removal) 10
Z (Stainless Steel)* 60, 25, 260*Only available in code 3 element length.
Elements may be stacked for 18” and 27” assemblies.
Order model code WL161E346NBC10 for same day shipment.
www.westernfilter.com 44
TMIN-TANK FILTERSSeries WL16 200 PSI
Dimensions: millimeters/(inches)
MED
IUM
PRES
SUR
ESP
IN-O
NFI
LTER
SLO
WPR
ESSU
RE
SPIN
-ON
FILT
ERS
IN-T
AN
KFI
LTER
SLO
WPR
ESSU
REFI
LTER
SM
EDIU
MPR
ESSU
REFI
LTER
SH
IGH
PRES
SURE
FILT
ERS
45 www.westernfilter.com
TMIN-TANK FILTERSSeries WL18 200 PSI
Available with reservoirmounting weld ring
Replacement elements available in C-PakTM
Dual pressure gauge ports
Optional second inlet port
Wide choice of gauges and switches
Optional check valve
Easy to service slotted cover
WL18200 gpm (568 l/min)
FEATURES
The WL18 in-tank filter unit is an ideal choice forflows up to 200 gpm. The E018 service elements areinterchangeable with Schroeder’s 18L series elements.An optional weld ring provides an easy solution toinsure a positive seal between housing and reservoir.The slotted cover makes for easy and efficient elementchange-outs. An optional secondary inlet port offersthe use of a second return line or placement of aquick disconnect to add pre-filtered initial fill ormake-up oil. These units can be top or side reservoirmounted. Use the optional anti-backflow valve wheninstalling this filter assembly to side of reservoir. Fivestandard grades of media are offered down to 4.0µ(c).
Western Filter elements are compatible withpetroleum oils, water glycol, oil/water, HWCF andsynthetic fluids.
Our WL18 Series is interchangeable with similarcompetitive units but is capable of higher flow ratesby utilizing Western Filter’s new high-flow bypassvalve.
Technical Data:
Maximum Working Pressure 200 psi (14 bar)
Rated Burst Pressure 300 psi max(21 bar)
Temperature Range Operating Buna N -45ºF to + 225ºF
(-45ºC to + 107ºC)Viton -20ºF to + 250ºF
(-29ºC to + 121ºC)
Head and Cover Material Aluminum
Canister Material Steel
WeightAssembly length 6 16 lbs. (7,3 kg.)
ACCESSORIES
Seal Kit - Buna N
Seal Kit - E.P.R.
Seal Kit - Viton
Weld Ring
Check Valve
Diffusor
P-233055-01
P-233055-02
P-233055-03
P-232964-01
P-138761
P-239291
www.westernfilter.com 46
TMIN-TANK FILTERSSeries WL18 200 PSI
Housing and Filter ElementFlow versus Pressure Drop150 SUS (32 cSt.) oil with specific gravity < 0.9
Viscosity Correction Formula∆P Element = psid from catalog X New Viscosity (SUS) X New Specific Gravity
150 0.90∆P Housing = psid from catalog X New Specific Gravity
0.90∆P Assembly = ∆P Element + ∆P Housing
MED
IUM
PRES
SUR
ESP
IN-O
NFI
LTER
SLO
WPR
ESSU
RE
SPIN
-ON
FILT
ERS
IN-T
AN
KFI
LTER
SLO
WPR
ESSU
REFI
LTER
SM
EDIU
MPR
ESSU
REFI
LTER
SH
IGH
PRES
SURE
FILT
ERS
GPM
PSID
Housing Only
0 20 40 60 80 100 120 140 1600
4
2
8
6
10
12
14
16
18
20
180 200
E018 - 18”
00 25 50 75 100 125 150
2468
101214
16
1820
GPM
PSID
C03
C05
C10C20
C01
175 200
47 www.westernfilter.com
TMIN-TANK FILTERSSeries WL18 200 PSI
Table 1Filter Assembly / Service Element
CODE DESCRIPTION
WL18 Assembly
E018 Element
Table 2Element Collapse Options
CODE DESCRIPTION
1 150 psid
Table 3Port Size Options
CODE PORT SIZE
J 2” SAE 4 Bolt Flange Code 61
Table 4Bypass Setting Options
CODE BYPASS SETTING
3 25 psid
4 50 psid
Table 6Assembly & Element Length
CODE (LGTH) ELEMENT LENGTH
6 (16.7”) 18”
Table 10Media Rating
CODE TARGET FLUID CLEANLINESS LEVEL
01 Flushing only
03 16/14/12 or better
05 18/16/14 or better
10 20/18/15 or better
20 22/19/16 or better
Note: Information concerning fluidcleanliness codes is on page 6, theMedia Grade Selection Guide.
Filter Assembly
Service Element
WL18 1 D 4 3 6 N B C
E018 1 B 6 C 10
TABLE 1 TABLE 2 TABLE 3 TABLE 4 TABLE 5 TABLE 6 TABLE 7 TABLE 8 TABLE 9
TABLE 1 TABLE 2 TABLE 8 TABLE 6 TABLE 9 TABLE 10
Table 5Upstream Pressure Gauge andSwitch Option
CODE INDICATOR STYLE & SETTING
1 No indicator2 0-200 psi pressure gauge 3 0-60 psi pressure gauge**4 0-60 psi pressure gauge*6 Pressure switch 18 psi
Brad Harrison (5-pin)7 Pressure switch 35 psi
Brad Harrison (5-pin)8 Pressure switch 18 psi
Hirschmann (4-pin)9 Pressure switch 35 psi
Hirschmann (4-pin)*Bypass setting option code 3 only
**Bypass setting option code 4 only
10TABLE 10
Table 7Secondary Port Options
CODE PORT SIZE
N None
J 2” SAE 4 Bolt FlangeCode 61
Table 8Seal Options
CODE MATERIAL
B Buna N
E E.P.R.
V Viton
Table 9Element Code
CODE DESCRIPTION
C (Glass) 01, 03, 05, 10, 20
www.westernfilter.com 48
TMIN-TANK FILTERSSeries WL18 200 PSI
MED
IUM
PRES
SUR
ESP
IN-O
NFI
LTER
SLO
WPR
ESSU
RE
SPIN
-ON
FILT
ERS
IN-T
AN
KFI
LTER
SLO
WPR
ESSU
REFI
LTER
SM
EDIU
MPR
ESSU
REFI
LTER
SH
IGH
PRES
SURE
FILT
ERS
Dimensions: millimeters/(inches)
49 www.westernfilter.com
IN-TANK FILTERSSeries WR10 100 PSI
Both electrical pressureswitch and gaugeavailable
Available with reservoir mounted weld ring
Built in air breather
Replacement elements available in C-Pak™and P-Pak™
Easy to service threaded cover
WR1020 GPM (75.7 l/min)
FEATURES
WR10 in-tank filters offer a space saving feature ofcombining a filter and breather. A compact andeconomical design made of aluminum head and glassfilled plastic screw-on cover allows flows up to 40GPM. Several port options are available. Two standardgrades of media are offered, 10µ(c) and 20µ(c).
Western Filter elements are compatible with petroleumoils, water glycol, oil/water, HWCF and synthetic fluids.
Technical Data:
Maximum Working Pressure 100 psi (6.9 bar)
Rated Burst Pressure 300 psi max(20.7 bar)
Temperature Range Operating Buna N -15ºF to + 230ºF
(-26ºC to + 110ºC)Viton -15ºF to + 230ºF
(-26ºC to + 110ºC)
Head Material Aluminum
Bowl and Cover Glass filled plastic
WeightAssembly length 2 0.85 lbs. (0,84 kg.)
ACCESSORIES
Seal Kit - Buna N
Seal Kit - E.P.R.
Seal Kit - Viton
Weld Ring
P-236854-01
P-236854-02
P-236854-03
P-236926
TM
www.westernfilter.com 50
IN-TANK FILTERSSeries WR10 100 PSI
Housing and Filter ElementFlow versus Pressure Drop150 SUS (32 cSt.) oil with specific gravity < 0.9
MED
IUM
PRES
SUR
ESP
IN-O
NFI
LTER
SLO
WPR
ESSU
RE
SPIN
-ON
FILT
ERS
IN-T
AN
KFI
LTER
SLO
WPR
ESSU
REFI
LTER
SM
EDIU
MPR
ESSU
REFI
LTER
SH
IGH
PRES
SURE
FILT
ERS
4
3
2
1
00 2 4 6 8 10 12 14 16 20
Housing Only
GPM
PSID
SAE-8
SAE-12 &NPT 3/4”
E
4
3
2
10
0 4 8 12 16 20GPM
PSID
ER10
5
6P10
P206
PSID
4
3
2
10
0 4 8 12 16 20GPM
PSID
SAE-8
SAE-12 &NPT 3/4”
ER10
5
6P10
P206
4
2
00 4 8 12 16 20
GPM
PSID
ER10
8
10C10
C20
Viscosity Correction Formula∆P Element = psid from catalog X New Viscosity (SUS) X New Specific Gravity
150 0.90∆P Housing = psid from catalog X New Specific Gravity
0.90∆P Assembly = ∆P Element + ∆P Housing
TM
TM
TM
TM
51 www.westernfilter.com
Table 1Filter Assembly / Service Element
CODE DESCRIPTION
WR10 Assembly
ER10 Element
Table 2Element Collapse Options
CODE DESCRIPTION
1 45 psid
Table 3Port Size Options
CODE PORT SIZE
O 3/4” - 16 UNF (SAE-8)A 1-1/16” - 12 UN (SAE-12) I 3/4” NPT
Table 4Bypass Setting Options
CODE BYPASS SETTING
3 25 psid
Table 7Assembly & Element Length
CODE (LGTH) ELEMENT LENGTH
2 (9.57”) 8”
Table 9Media Rating
CODE TARGET FLUID CLEANLINESS LEVEL
10 20/18/15 or better
20 22/19/16 or better
Note: Information concerning fluidcleanliness codes is on page 6, theMedia Grade Selection Guide.
Filter Assembly
Service Element
WR10 1 A 3 4 B 2 C 10
ER10 1 B 2 C 10
TABLE 1 TABLE 2 TABLE 3 TABLE 4 TABLE 5 TABLE 6 TABLE 7 TABLE 8 TABLE 9
TABLE 1 TABLE 2 TABLE 6 TABLE 7 TABLE 8 TABLE 9
CTABLE 10
Table 6Seal Options
CODE MATERIAL
B Buna
E E.P.R.
V Viton A
Table 8Element Code
CODE MEDIA TYPE
C (Glass media) 10, 20
P (Cellulose) 10, 20
Table 5Upstream Pressure Gauge andSwitch Option
CODE UPSTREAM PRESSURE GAUGEAND SWITCH OPTIONS
1 No indicator4 0-60 psi pressure gauge6 Electrical switch 18 psi
Brad Harrison (5-pin)8 Electrical switch 18 psi
Hirschmann (4-pin)
Table 10Accessories
OMIT No accessories
C 7 micron air breather
D 40 micron air breather
IN-TANK FILTERSSeries WR10 100 PSI
TM
TM
TM
TM
www.westernfilter.com 52
Dimensions: millimeters/(inches)
IN-TANK FILTERSSeries WR10 100 PSI
MED
IUM
PRES
SUR
ESP
IN-O
N F
ILTE
RS
LOW
PRES
SUR
ESP
IN-O
N F
ILTE
RS
IN-T
AN
K F
ILTE
RS
LOW
PRE
SSU
RE F
ILTE
RSM
EDIU
M P
RESS
URE
FIL
TERS
HIG
H P
RESS
URE
FIL
TERS
WR10 SeriesLow Pressure Series
70.10(2.76)
50.04(1.97)
82.04(3.23)
87.88(3.46)
27.94(1.10)
Ø41.15(1.62)
Ø74.93(2.95)
2.03(.08)
243.08(9.57)
23.88(.94)
178.05(7.01)
Ø27.94(1.10)
Inlet Port
11.18(.44)
16.00(.63)
Typ.
Ø61.47(2.42)
Ø43.69(1.72)
Outletto Tank
1/8" NPT(Gauge Port Plugged)2 Plcs
TM
TM
TM
TM
53 www.westernfilter.com
IN-TANK FILTERSSeries WR11 100 PSI
Reservoir can be filledthrough the filter
Replacement elements available in C-PakTM and P-PakTM
Both electricalpressure switch and gauge available
Available withreservoir mountedweld ring
Built in air breather
Easy to service quick disconnectcover without tooling
WR1140 gpm (151 l/min)
FEATURES
WR11 in-tank filters offer a space saving feature ofcombining a filter and breather. A compact andeconomical design made of aluminum head and glassfilled plastic screw-on cover allows flows up to 40GPM. Several port options and three bowl lengths areavailable. Two standard grades of media are offered.
Western Filter elements are compatible withpetroleum oils, water glycol, oil/water, HWCF andsynthetic fluids.
Technical Data:
Maximum Working Pressure 100 psi (6.9 bar)
Rated Burst Pressure 300 psi max(20.7 bar)
Temperature Range Operating Buna N -15ºF to + 230ºF
(-26ºC to + 110ºC)Viton -15ºF to + 230ºF
(-26ºC to + 110ºC)
Head Material Aluminum
Bowl and Cover Glass filled plastic
WeightAssembly length 1 1.78 lbs. (0,81 kg.)Assembly length 2 1.84 lbs. (0,84 kg.)Assembly length 3 1.94 lbs. (0,88 kg.)
ACCESSORIES
Seal Kit - Buna N
Seal Kit - E.P.R.
Seal Kit - Viton
Weld Ring
P-236855-01
P-236855-02
P-236855-03
P-236927
TM
TM
TM
TM
54
IN-TANK FILTERSSeries WR11 100 PSI
Housing and Filter ElementFlow versus Pressure Drop150 SUS (32 cSt.) oil with specific gravity < 0.9
C10
ER11 - 5”
PSID
0
4
8
12
16
20
80GPM
16 24 32 40
C20
P10
ER11 - 5”PS
ID
0
2
4
6
8
10
80GPM
16 24 32 40
P20
0
2
3
4
0
GPM
PSID
Housing Only
1
5 10 15 20 25 30 35 40
SAE 12 & 3/4” NPT
SAE 16 & 1” NPT
C10
ER11 - 8”
PSID
0
2
4
6
8
10
80GPM
16 24 32 40
C20
P10
ER11 - 8”
PSID
0
1
2
3
4
5
80GPM
16 24 32 40
P20
6
C10
ER11 - 12”
PSID
0
1
2
3
4
5
80GPM
16 24 32 40
C20
1.5
3
4.5
6
PSID
GPM
00
8 16 24 32 40
P20
P10
ER11 - 12”
MED
IUM
PRES
SUR
ESP
IN-O
N F
ILTE
RS
LOW
PRES
SUR
ESP
IN-O
N F
ILTE
RS
IN-T
AN
K F
ILTE
RS
LOW
PRE
SSU
RE F
ILTE
RSM
EDIU
M P
RESS
URE
FIL
TERS
HIG
H P
RESS
URE
FIL
TERS
Viscosity Correction Formula∆P Element = psid from catalog X New Viscosity (SUS) X New Specific Gravity
150 0.90∆P Housing = psid from catalog X New Specific Gravity
0.90∆P Assembly = ∆P Element + ∆P Housing
www.westernfilter.com
TM
TM
TM
TM
55 www.westernfilter.com
Table 1Filter Assembly / Service Element
CODE DESCRIPTION
WR11 Assembly
ER11 Element
Table 2Element Collapse Options
CODE DESCRIPTION
1 45 psid
Table 3Port Size Options
CODE PORT SIZE
A 1-1/16” - 12 UN (SAE-12)B 1-5/16” - 12 UN (SAE-16) I 3/4” NPT
Y 1” NPT
Table 4Bypass Setting Options
CODE BYPASS SETTING
3 25 psid
Table 7Assembly & Element Length
CODE (LGTH) ELEMENT LENGTH
1 (4.33”) 5”
2 (6.89”) 8”
3 (10.83”) 12”
Table 9Media Rating
CODE TARGET FLUID CLEANLINESS LEVEL
10 20/18/15 or better
20 22/19/16 or better
Note: Information concerning fluidcleanliness codes is on page 6, theMedia Grade Selection Guide.
Filter Assembly
Service Element
WR11 1 A 3 4 6 2 C 10
ER11 1 B 2 C 10
TABLE 1 TABLE 2 TABLE 3 TABLE 4 TABLE 5 TABLE 6 TABLE 7 TABLE 8 TABLE 9
TABLE 1 TABLE 2 TABLE 6 TABLE 7 TABLE 8 TABLE 9
CTABLE 10
Table 6Seal Options
CODE MATERIAL
B Buna N
E E.P.R.
V Viton
Table 8Element Code
CODE DESCRIPTION
C (Glass) 10, 20
P (Cellulose) 10
Table 5Upstream Pressure Gauge andSwitch Option
CODE UPSTREAM PRESSURE GAUGEAND SWITCH OPTIONS
1 No indicator4 0-60 psi pressure gauge6 Electrical switch 18 psi
Brad Harrison (5-pin)8 Electrical switch 18 psi
Hirschmann (4-pin)
Table 10Accessories
CODE BREATHER
OMIT No breather
C 7 micron air breather
D 40 micron air breather
IN-TANK FILTERSSeries WR11 100 PSI
TM
TM
TM
TM
www.westernfilter.com 56
103.89(4.09)
Refer To Model Code
(Assembly Length)
36.07(1.42)
1.52(.06)
115.06(4.53)
109.98(4.33)
70.10(2.76)
41.15(1.62)
37.08(1.46)
11.18(.44)
89.92(3.54)
Inlet Port
Typ
88.90(3.50)
71.63(2.82)
Outletto Tank
83.06(3.27)
1/8" NPT(Gauge Port Plugged)
2 Plcs
Dimensions: millimeters/(inches)
IN-TANK FILTERSSeries WR11 100 PSI
MED
IUM
PRES
SUR
ESP
IN-O
N F
ILTE
RS
LOW
PRES
SUR
ESP
IN-O
N F
ILTE
RS
IN-T
AN
K F
ILTE
RS
LOW
PRE
SSU
RE F
ILTE
RSM
EDIU
M P
RESS
URE
FIL
TERS
HIG
H P
RESS
URE
FIL
TERS
Typical
TM
TM
TM
TM
www.westernfilter.com
IN-TANK FILTERSSeries WR14 150 PSI
Diffusor helps preventaeration of the fluid andmay also eliminate reservoir baffle plate
Replacement elements available in C-PakTM
and P-PakTM
Wide choice of servicegauges and switches
Four element lengths available
Return line applicationinside out flow
Magnetic “pre-filtration” offerrous particles
Reservoir can be filled through the filter
Optional weld ring
Simplified bypass design prevents flushing previouslycollected contaminants back into the system
WR14160 gpm (606 l/min)
FEATURES
The WR series of in-tanks feature inside-to-out flowthrough the element, which means that dirt iscollected inside the filter cartridge. This ensures thatcontamination is retained inside the cartridge whenthe element is serviced. A heavy duty magnetic core isattached to the element retention rod ensuring pre-filtration of ferrous particles entering the reservoir. An optional weld ring provides an easy solution toinsure a positive seal between housing and reservoir.The slotted cover makes for easy and efficient elementchange-outs. Fluid aeration in large flow applicationscan be minimized by the use of our optional diffusor.Three standard grades of media are offered down to6.4µ(c).
Western Filter elements are compatible withpetroleum oils, water glycol, oil/water, HWCF andsynthetic fluids.
Technical Data:
Maximum Working Pressure 150 psi (10.3 bar)
Rated Burst Pressure 420 psi max(28.9 bar)
Temperature Range Operating Buna N -15ºF to + 230ºF
(-26 C to + 110ºC)Viton -15ºF to + 230 F
(-26ºC to + 110ºC)
Head and Cover Material Aluminum
Diffusor Material Steel
Weight (without elements)Assembly length 1 2.6 lbs. (1,18 kg.)Assembly length 2 3.1 lbs. (1,41 kg.)Assembly length 3 3.3 lbs. (1,50 kg.)Assembly length 4 3.7 lbs. (1,68 kg.)
ACCESSORIES
Seal Kit - Buna N
Seal Kit - E.P.R.
Seal Kit - Viton
Weld Ring
P-236856-01
P-236856-02
P-236856-03
P-236928
57
TM
TM
TM
TM
www.westernfilter.com 58
IN-TANK FILTERSSeries WR14 150 PSI
MED
IUM
PRES
SUR
ESP
IN-O
N F
ILTE
RS
LOW
PRES
SUR
ESP
IN-O
N F
ILTE
RS
IN-T
AN
K F
ILTE
RS
LOW
PRE
SSU
RE F
ILTE
RSM
EDIU
M P
RESS
URE
FIL
TERS
HIG
H P
RESS
URE
FIL
TERS
Housing and Filter ElementFlow versus Pressure Drop150 SUS (32 cSt.) oil with specific gravity < 0.9
Viscosity Correction Formula∆P Element = psid from catalog X New Viscosity (SUS) X New Specific Gravity
150 0.90∆P Housing = psid from catalog X New Specific Gravity
0.90∆P Assembly = ∆P Element + ∆P Housing
4
3
2
1
00 10 20 30 40 50 60 70 80
Housing Only
GPM
PSID
SAE-12/3/4” NPT
SAE-16/1” NPTSAE-20/1-1/4” NPT
65
21
00 4 8 12 16 20 24
GPM
PSID
43
ER14-4”
P10
24
18
6
00 4 8 12 16 20 24
GPM
PSID 12
ER14-4”
C10
65
21
00 8 16 24 32 40
GPM
PSID
43
ER14-6”
P10
2420
84
00 8 16 24 32 40
GPM
PSID
1612
ER14-6”
C10
8
2
00 8 16 24 32 40
GPM
PSID
6
4
ER14-8”
P10
16
12
4
00 8 16 24 32 40
GPM
PSID 8
ER14-8”
C10
4
1
00 8 16 24 32 40
GPM
PSID
3
2
ER14-12”
P10
12
10
420
0 8 16 24 32 40
GPM
PSID
86
ER14-12”
C10
C05
C20
C05
C20
C05
C20
C05
C20
TM
TM
TM
TM
www.westernfilter.com59
Table 1Filter Assembly / Service Element
CODE DESCRIPTION
WR14 Assembly
ER14 Element
Table 2Element Collapse Options
CODE DESCRIPTION
1 150 psid (10.3 BAR)
Table 3Port Size Options
CODE PORT SIZE
A 1-1/16” - 12 UN (SAE-12)B 1-5/16” - 12 UN (SAE-16)C 1-5/8” - 12 UN (SAE-20)I 3/4” NPTP 1-1/4” NPTY 1” NPT
Table 4Bypass Setting Options
CODE BYPASS SETTING
3 25 psid
Table 7Assembly & Element Length
CODE (LGTH) ELEMENT LENGTH
1 (7.8”) 4.0”
2 (7.8”) 6.0”
3 (9.8”) 8.0”
4 (13.8”) 12.0”
Table 9Media Rating
CODE TARGET FLUID CLEANLINESS LEVEL
05 18/16/14 or better
10 20/18/15 or better
20 22/19/16 or better
Note: Information concerning fluidcleanliness codes is on page 6, theMedia Grade Selection Guide.
Filter Assembly
Service Element
WR14 1 A 3 4 B 1 C 10
ER14 1 B 2 C 10
TABLE 1 TABLE 2 TABLE 3 TABLE 4 TABLE 5 TABLE 6 TABLE 7 TABLE 8 TABLE 9
TABLE 1 TABLE 2 TABLE 6 TABLE 7 TABLE 8 TABLE 9
FTABLE 10
Table 6Seal Options
CODE MATERIAL
B Buna
E E.P.R.
V Viton A
Table 8Element Code
CODE DESCRIPTION
C (Glass) 05, 10, 20
P (Cellulose) 10
Table 10Accessories
CODE DIFFUSOR
Omit No diffusor
F With diffusor
Table 5Upstream Pressure Gauge andSwitch Option
CODE UPSTREAM PRESSURE GAUGEAND SWITCH OPTIONS
1 No indicator2 0-200 psi pressure gauge 4 0-60 psi pressure gauge6 Electrical switch 18 psi
Brad Harrison (5-pin)8 Electrical switch 18 psi
Hirschmann (4-pin)
IN-TANK FILTERSSeries WR14 150 PSI
TM
TM
TM
TM
www.westernfilter.com 60
LOW
PRES
SUR
ESP
IN-O
N F
ILTE
RS
HIG
HPR
ESSU
RE
SPIN
-ON
FIL
TER
SIN
-TA
NK
FIL
TER
SLO
W P
RESS
URE
FIL
TERS
MED
IUM
PRE
SSU
RE F
ILTE
RSH
IGH
PRE
SSU
RE F
ILTE
RS
Dimensions: millimeters/(inches)
IN-TANK FILTERSSeries WR14 150 PSI
MED
IUM
PRES
SUR
ESP
IN-O
N F
ILTE
RS
LOW
PRES
SUR
ESP
IN-O
N F
ILTE
RS
IN-T
AN
K F
ILTE
RS
LOW
PRE
SSU
RE F
ILTE
RSM
EDIU
M P
RESS
URE
FIL
TERS
HIG
H P
RESS
URE
FIL
TERS
Telephone 661.295.0800 • Fax 661.295.8443 • www.westernfilter.com
26235 Technology Drive • Valencia, California 91355© Western Filter 2005R0052005-WR14
Min. Required for Element Removal:Code 1: 231.14 (9.10)Code 2: 274.32 (10.80)Code 3: 325.12 (12.80)Code 4: 444.50 (17.50)
Ø8.89 (.35) On BC116.08 (4.57) 2 Plcs
Ø8.89 (.35) On BC 125.98 (4.96) 4 Plcs.
Ø88.90(3.50)Diffusor
Ø71.12(2.80)Element
Inlet Port
30.48(1.20)
38.10(1.50)
22.35(.88)
88.90(3.50)
Refer ToModel Code
(Assembly Length)
109.98(4.33)
137.16(5.40)
109.98(4.33)
140.97(5.55)
1/8" NPT
(Gauge Port Plugged) 2 Plcs.
TM
TM
TM
TM
61 www.westernfilter.com
FEATURES
The WR series of in-tanks feature inside-to-out flowthrough the element, which means that dirt iscollected inside the filter cartridge. This ensures thatcontamination is retained inside the cartridge whenthe element is serviced. A heavy duty magnetic core isattached to the element retention rod ensuring pre-filtration of ferrous particles entering the reservoir. An optional weld ring provides an easy solution toinsure a positive seal between housing and reservoir.The slotted cover makes for easy and efficient elementchange-outs. Fluid aeration in large flow applicationscan be minimized by the use of our optional diffusor.Three standard grades of media are offered down to6.4µ(c).
Western Filter elements are compatible withpetroleum oils, water glycol, oil/water, HWCF andsynthetic fluids.
ACCESSORIES
Seal Kit - Buna N
Seal Kit - E.P.R.
Seal Kit - Viton
Weld Ring
P-236857-01
P-236857-02
P-236857-03
P-236929
IN-TANK FILTERSSeries WR15 150 PSI
Diffusor helps preventaeration of the fluid andmay also eliminate reservoir baffle plate
Replacement elements available in C-PakTM
and P-PakTM
Wide choice of servicegauges and switches
Three element lengths available
Return line applicationinside out flow
Magnetic “pre-filtration” offerrous particles
Reservoir can be filled through the filter
Optional weld ring
WR15160 gpm (606 l/min)
Technical Data:
Maximum Working Pressure 150 psi (10.3 bar)
Rated Burst Pressure 420 psi max(28.9 bar)
Temperature Range Operating Buna N -15ºF to + 230ºF
(-26 C to + 110ºC)Viton -15ºF to + 230 F
(-26ºC to + 110ºC)
Head and Cover Material Aluminum
Diffusor Material Steel
Weight (without elements)Assembly length 2 9.2 lbs. (4,18 kg.)Assembly length 3 10.3 lbs. (4,68 kg.)Assembly length 4 11.0 lbs. (5,00 kg.)
TM
TM
TM
TM
www.westernfilter.com 62
Housing and Filter ElementFlow versus Pressure Drop150 SUS (32 cSt.) oil with specific gravity < 0.9
IN-TANK FILTERSSeries WR15 150 PSI
MED
IUM
PRES
SUR
ESP
IN-O
N F
ILTE
RS
LOW
PRES
SUR
ESP
IN-O
N F
ILTE
RS
IN-T
AN
K F
ILTE
RS
LOW
PRE
SSU
RE F
ILTE
RSM
EDIU
M P
RESS
URE
FIL
TERS
HIG
H P
RESS
URE
FIL
TERS
400
GPM
PSID
80 120 1600
2
4
6
8
10Housing Only
200
GPM
40 60 80
PSID
0
2
4
8
6
ER15 - 8”
P10
4
8
12
16
20
24
PSID
GPM
00
20 40 60 80 100
C05
C10
ER15 - 8”
120 140 160
C20
ER15 - 10”
PSID
0
4
8
12
16
20
0GPM
40 80 120 160
C10
24
C05
C20
ER15 - 10”
PSID
0
2
4
6
8
10
0GPM
40 80 120 160
P10
12
ER15 - 18”
PSID
0
2
4
6
8
10
0GPM
40 80 120 160
C05
12
C10
C20
ER15 - 18”
PSID
0
1
2
3
4
5
0GPM
40 80 120 160
6
P10
Viscosity Correction Formula∆P Element = psid from catalog X New Viscosity (SUS) X New Specific Gravity
150 0.90∆P Housing = psid from catalog X New Specific Gravity
0.90∆P Assembly = ∆P Element + ∆P Housing
400
GPM
PSID
80 120 1600
2
4
6
8
10Housing Only
200
GPM
40 60 80
PSID
0
2
4
8
6
ER15 - 8”
P10
4
8
12
16
20
24
PSID
GPM
00
20 40 60 80 100
C05
C10
ER15 - 8”
120 140 160
C20
ER15 - 10”
PSID
0
4
8
12
16
20
0GPM
40 80 120 160
C10
24
C05
C20
ER15 - 10”
PSID
0
2
4
6
8
10
0GPM
40 80 120 160
P10
12
ER15 - 18”
PSID
0
2
4
6
8
10
0GPM
40 80 120 160
C05
12
C10
C20
ER15 - 18”
PSID
0
1
2
3
4
5
0GPM
40 80 120 160
6
P10
TM
TM
TM
TM
63 www.westernfilter.com
Table 1Filter Assembly / Service Element
CODE DESCRIPTION
WR15 Assembly
ER15 Element
Table 2Element Collapse Options
CODE DESCRIPTION
1 150 psid
Table 3Port Size Options
CODE PORT SIZE
D 1-7/8” - 12 UN (SAE-24)U 1-1/2” NPTE 1-1/2” SAE 4 Bolt Flange
Code 61
Table 4Bypass Setting Options
CODE BYPASS SETTING
3 25 psid
Table 7Assembly & Element Length
CODE (LGTH) ELEMENT LENGTH
2 (9.8”) 8.0”
3 (12.6”) 10.0”
4 (20.7”) 18.0”
Table 9Media Rating
CODE TARGET FLUID CLEANLINESS LEVEL
03 16/14/12 or better
05 18/16/14 or better
10 20/18/15 or better
20 22/19/16 or better
Note: Information concerning fluidcleanliness codes is on page 6, theMedia Grade Selection Guide.
Filter Assembly
Service Element
WR15 1 D 3 4 B 2 C 10
ER15 1 B 2 C 10
TABLE 1 TABLE 2 TABLE 3 TABLE 4 TABLE 5 TABLE 6 TABLE 7 TABLE 8 TABLE 9
TABLE 1 TABLE 2 TABLE 6 TABLE 7 TABLE 8 TABLE 9
FTABLE 10
Table 6Seal Options
CODE MATERIAL
B Buna N
E E.P.R.
V Viton
Table 8Element Code
CODE DESCRIPTION
C (Glass) 05, 10, 20
P (Cellulose) 10
Table 10Accessories
CODE DIFFUSOR
Omit No diffusor
F With diffusor
Table 5Upstream Pressure Gauge andSwitch Option
CODE UPSTREAM PRESSURE GAUGEAND SWITCH OPTIONS
1 No indicator2 0-200 psi pressure gauge 4 0-60 psi pressure gauge6 Electrical switch 18 psi
Brad Harrison (5-pin)8 Electrical switch 18 psi
Hirschmann (4-pin)
IN-TANK FILTERSSeries WR15 150 PSI
TM
TM
TM
TM
www.westernfilter.com 64
Min. Required for Element Removal:Code 2: 309.88 (12.20)Code 3: 381.00 (15.00)Code 4: 579.12 (22.80)
129.54(5.10)
Refer To Model Code
(Assembly Length)
50.80(2.00)
88.90(3.50)
99.06(3.90)
35.56(1.40)
1/8" NPT(Gauge Port, Plugged)2 Plcs.
133.10 (5.24)
Inlet Port
172.47(6.79)
10.92(.43)4 Plcs.175.00
(6.89)
Tank MountingHoles
106.68(4.20)
Dimensions: millimeters/(inches)
IN-TANK FILTERSSeries WR15 150 PSI
MED
IUM
PRES
SUR
ESP
IN-O
N F
ILTE
RS
LOW
PRES
SUR
ESP
IN-O
N F
ILTE
RS
IN-T
AN
K F
ILTE
RS
LOW
PRE
SSU
RE F
ILTE
RSM
EDIU
M P
RESS
URE
FIL
TERS
HIG
H P
RESS
URE
FIL
TERS
TM
TM
TM
TM
65 www.westernfilter.com
Simplified bypass designprevents flushing previously collected contaminants back into the system
Diffusor helps preventaeration of the fluid and may alsoeliminate reservoir baffle plate
Replacement elements available in C-PakTM
and P-PakTM
Return line application inside out flow
Magnetic “pre-filtration” of ferrous particles
Reservoir can be filled through the filter
Wide choice of service gauges and switches
Four element lengths available
WR17320 gpm (1211 l/min)
FEATURES
The WR17 series in-tank features inside-to-out flowthrough the element which means dirt is collectedinside the filter cartridge. This ensures thatcontamination is retained inside the cartridge whenthe element is serviced. A heavy duty magnetic core isattached to the element retention rod ensuring pre-filtration of ferrous particles entering the reservoir. An optional weld ring provides an easy solution toinsure a positive seal between housing and reservoir.The slotted cover makes for easy and efficient elementchange-outs. Fluid aeration in large flow applicationscan be minimized by the use of our optional diffusor.Three standard grades of media are offered down to6.4µ(c).
Western Filter elements are compatible withpetroleum oils, water glycol, oil/water, HWCF andsynthetic fluids.
Technical Data:
Maximum Working Pressure 150 psi (10.3 bar)
Rated Burst Pressure 420 psi max(28.9 bar)
Temperature Range Operating Buna N -15ºF to + 230ºF
(-26ºC to + 110ºC)Viton -15ºF to + 230ºF
(-26ºC to + 110ºC)
Head and Cover Material Aluminum
Diffusor Material Steel
Weight (without elements)Assembly length 2 17.6 lbs. (8 kg.)Assembly length 3 18.5 lbs. (8,4 kg.)Assembly length 4 18.9 lbs. (8,6 kg.)Assembly length 5 20.0 lbs. (9,1 kg.)
ACCESSORIES
Seal Kit - Buna N
Seal Kit - E.P.R.
Seal Kit - Viton
Weld Ring
P-236858-01
P-236858-02
P-236858-03
P-236930
IN-TANK FILTERSSeries WR17 150 PSI
TM
TM
TM
TM
www.westernfilter.com 66
Housing and Filter ElementFlow versus Pressure Drop150 SUS (32 cSt.) oil with specific gravity < 0.9
IN-TANK FILTERSSeries WR17 150 PSI
MED
IUM
PRES
SUR
ESP
IN-O
N F
ILTE
RS
LOW
PRES
SUR
ESP
IN-O
N F
ILTE
RS
IN-T
AN
K F
ILTE
RS
LOW
PRE
SSU
RE F
ILTE
RSM
EDIU
M P
RESS
URE
FIL
TERS
HIG
H P
RESS
URE
FIL
TERS
Viscosity Correction Formula∆P Element = psid from catalog X New Viscosity (SUS) X New Specific Gravity
150 0.90∆P Housing = psid from catalog X New Specific Gravity
0.90∆P Assembly = ∆P Element + ∆P Housing
800
GPM
160 240 320
PSID
0
1
2
4
3Housing Only
ER17 - 8”
PSID
0
4
8
12
16
20
0GPM
40 80 120 160
C10
24
C05
C20
400
GPM
80 120 160
PSID
0
2
4
8
6
ER17 - 11”
P10
ER17 - 15”
PSID
0
4
8
12
16
20
0GPM
80 160 240 320
C10
24
C05
C20
400
GPM
80 120 160
PSID
0
2
4
8
6
ER17 - 8”
P10
ER17 - 11”
PSID
0
4
8
12
16
20
0GPM
40 80 120 160
C10
24
C05
C20
800
GPM
160 240 320
PSID
0
2
4
8
6
ER17 - 15”
P10
10
ER17 - 19”
PSID
0
4
8
12
16
20
0GPM
80 160 240 320
C10
24
C05
C20
800
GPM
160 240 320
PSID
0
2
4
8
6
ER17 - 19”
P10
TM
TM
TM
TM
67 www.westernfilter.com
Table 1Filter Assembly / Service Element
CODE DESCRIPTION
WR17 Assembly
ER17 Element
Table 2Element Collapse Options
CODE DESCRIPTION
1 150 psid
Table 3Port Size Options
CODE PORT SIZE
K 2-1/2” SAE 4 Bolt FlangeCode 61
Table 4Bypass Setting Options
CODE BYPASS SETTING
3 25 psid Table 7Assembly & Element Length
CODE (LGTH) ELEMENT LENGTH
2 (11.4”) 8.00”
3 (14.6”) 11.00”
4 (18.5”) 15.00”
5 (22.0”) 19.00
Table 9Media Rating
CODE TARGET FLUID CLEANLINESS LEVEL
03 16/14/12 or better
05 18/16/14 or better
10 20/18/15 or better
20 22/19/16 or betterNote: Information concerning fluidcleanliness codes is on page 6, theMedia Grade Selection Guide.
Filter Assembly
Service Element
WR17 1 K 3 4 B 2 C 10
ER17 1 B 3 C 10
TABLE 1 TABLE 2 TABLE 3 TABLE 4 TABLE 5 TABLE 6 TABLE 7 TABLE 8 TABLE 9
TABLE 1 TABLE 2 TABLE 6 TABLE 7 TABLE 8 TABLE 9
FTABLE 10
Table 6Seal Options
CODE MATERIAL
B Buna N
E E.P.R.
V Viton
Table 8Element Code
CODE DESCRIPTION
C (Glass) 05, 10, 20
P (Cellulose) 10
Table 10Accessories
CODE DIFFUSOR
Omit No diffusor
F With diffusor
Table 5Upstream Pressure Gauge andSwitch Option
CODE UPSTREAM PRESSURE GAUGEAND SWITCH OPTIONS
1 No indicator2 0-200 psi pressure gauge 4 0-60 psi pressure gauge6 Electrical switch 18 psi
Brad Harrison (5-pin)8 Electrical switch 18 psi
Hirschmann (4-pin)
IN-TANK FILTERSSeries WR17 150 PSI
TM
TM
TM
TM
www.westernfilter.com 68
Code 2: 350.52(13.80) Code 3: 429.26(16.90) Code 4: 579.12(22.80)
Element Removal
Refer ToModel Code
(Assembly Length)
185.42(7.30)
111.76(4.40)
217.42(8.56)
12.95(.51)(4 Plcs.)
109.22(4.30)
127.00(5.00)
154.94(6.10)
Inlet Port
55.88(2.20)
55.88(2.20)
1/8" NPT(Gauge Port Plugged)
2 Plcs.
165.61(6.52)
Code 5: 619.76(24.40)
Tank Mounting Holes
Clearance for
Dimensions: millimeters/(inches)
IN-TANK FILTERSSeries WR17 150 PSI
MED
IUM
PRES
SUR
ESP
IN-O
N F
ILTE
RS
LOW
PRES
SUR
ESP
IN-O
N F
ILTE
RS
IN-T
AN
K F
ILTE
RS
LOW
PRE
SSU
RE F
ILTE
RSM
EDIU
M P
RESS
URE
FIL
TERS
HIG
H P
RESS
URE
FIL
TERS
TM
TM
TM
TM