of 15
8/20/2019 X5 Navigation Retrofit
1/37
Parts and AccessoriesInstallation Instructions
Retrofit / Installation kit No. 65 90 0 136 497 (others see cover sheet) Issue date: 09.2001 Installation Instructions No. 01 29 0 136 499
On-board monitor and navigation system retrofit kit
(wide screen monitor)
BMW X5 (E
53)
These installation instructions are only valid for cars with SA555
high on-board computer.
Specialist and electrical knowledge required.
The installation time is 7.5 hours but this may vary depending on the condition of the car andthe equipment in it.
Retrofit/Installation kit No. 65 90 0 136 497
053 0001 B
1 4
2 5
6
MODE
FM AM
3
MENU
INFO
TONESELECT
8/20/2019 X5 Navigation Retrofit
2/37
8/20/2019 X5 Navigation Retrofit
3/37
EN/1
Retrofit / Installation kit No. 65 90 0 136 497 (others see cover sheet) Issue date: 09.2001 Installation Instructions No. 01 29 0 136 499
Important information on the installation of the on-board monitor and navigationsystem
For use within the BMW dealership organisation only.
The on-board monitor and the navigation system may only installed by a specialist workshopwhich has available the necessary special tools and the manuals (maintenance, repair,diagnostics, etc.).
When installing cables/leads ensure that they are not kinked or damaged.
Any additional cables/leads you install should be secured where necessary with cable ties.
Item numbers refer only to the diagrams and to the texts next to the appropriate figure.
All work is shown on a LHD car.Proceed in exactly the same way on RHD cars.
Electrical knowledge required.
Subject to technical modifications
Required tools and equipment
MoDIC III or DIS Cable lamp1/2 inch socket set Angle cutter1/4 inch socket set Universal knifeSet of Torx socket Pneumatic sawSet of Philips screwdrivers Oscillating sawSet of flat screwdrivers Flat filesSet of Phillips screwdrivers, short Combination pliers
Angle drill Torque wrenchSet of drill bits Textile adhesive tapeConical countersink Extraction unitCrimping pliers (for butt-joint connectors) Hot air blower
On cars with a production date after 10/00
(cars with a new generation radio connectionplug), which have standard telephone preparation, a standard telephone or a standardretrofit telephone the retrofit switch module kit, installation instructions 01 29 0 136 390must also
be installed before the installation
of the on-board monitor and navigationsystem retrofit kit.
"
The on-board monitor radio / CD changer control cable is not supplied with the installation
kit and must be ordered separately for cars with a CD changer without a DSP amplifier usingthe electronic parts catalogue (EPC) .
"
The existing aerial amplifier must be replaced on cars with a production date after 10/00
(cars with a new generation radio connection plug) with an aerial amplifier for cars with aproduction date before 10/00
(cars without a new generation radio connection plug). Thisaerial amplifier is not supplied with the installation kit and must be ordered separately tomatch the car’s equipment using the electronics parts catalogue (EPC).
"
8/20/2019 X5 Navigation Retrofit
4/37
EN/2
Retrofit / Installation kit No. 65 90 0 136 497 (others see cover sheet) Issue date: 09.2001 Installation Instructions No. 01 29 0 136 499
1. Preparations
TISinstruction
No.
Print out the error memory -
Disconnect the battery 12 00 ...Remove the décor strip next to the steering column 51 16 221
Remove the décor strip above the glove compartment 51 16 221
Unclip the radio compartment flap (no longer required) 51 16 221
Remove the radio (no longer required) 65 11 030
Remove the control (no longer required) 65 81 010
Remove the centre fresh air grille 64 22 161
Remove the air conditioning control 64 11 749
Remove the instrument cluster 62 21 000
Remove the left front seat 52 14 000
Remove the heating / ventilation duct under the left front seat -
Remove the centre seat belt mounting on the rear seat 52 26 005Remove the rear seat bench 52 26 005
Remove the left side section of the rear seat backrest 52 26 008
Remove the door sill strips at the front and rear left 51 47 000
Remove the bottom section of the B pillar trim on the left 51 43 150
Remove the rear left centre console 51 16 204
Remove the front left centre console 51 16 200
Remove the pedal trim (LHD cars only) 51 45 185
Remove the bottom left instrument panel trim (LHD cars only) 51 45 180
Remove the glove compartment (RHD cars only) 51 16 360
Remove the left footwell trim (RHD cars only) 51 45 181
Release the left instrument panel near the air conditioning control -
Remove the right footwell trim (LHD cars only) 51 45 181
Remove the front right door sill strip (LHD cars only) 51 47 000
Remove the bottom right A pillar trim (LHD cars only) 51 43 075
Remove the front right centre console trim (LHD cars only) 51 16 200
Remove the bottom left A pillar trim (RHD cars only) 51 43 075
Remove the rear footwell light 63 31 023
Raise the carpet at the left -
Remove the boot luggage net and blind -
Release the C pillar trim on the left 51 43 251
Remove the boot lid on the both sides 51 47 172Remove the mounting for the warning triangle -
Remove the roller supports for the load floor on both sides (if fitted) -
Remove the load edge trim 51 46 050
Remove the D pillar trim on the left 51 43 252
Remove the ventilation grille on the left. 51 37 261
Remove the ventilation grille holder on the left 51 37 261
Remove the boot floor trims on both sides (if fitted) -
Remove the boot carpet (if fitted) 51 47 101
Remove the spare wheel cover (if fitted) -
Remove the left boot trim 51 47 151
Remove the rear side member supports on both sides 51 46 050Remove the spare wheel -
8/20/2019 X5 Navigation Retrofit
5/37
EN/3
Retrofit / Installation kit No. 65 90 0 136 497 (others see cover sheet) Issue date: 09.2001 Installation Instructions No. 01 29 0 136 499
1. Preparations
.
TISinstruction
No.
Remove the chock mounting -
Release the air supply system for the pneumatic suspension and push it
forwards (if fitted) 37 22 540
Remove the multi-purpose tray cover under the spare wheel -
Remove the top interior boot lid trim 51 49 056
Remove the side interior trims on both sides of the boot lid 51 49 053
Take the rear spoiler off the top outside of the boot lid 51 71 412
8/20/2019 X5 Navigation Retrofit
6/37
EN/4
Retrofit / Installation kit No. 65 90 0 136 497 (others see cover sheet) Issue date: 09.2001 Installation Instructions No. 01 29 0 136 499
2. Parts list
0
1 On-board monitor wiring harness2 Aerial extension for GPS aerial3 GPS aerial4 Top on-board monitor holder5 Left on-board monitor holder6 Right on-board monitor holder7 Self-tapping screw 3.5x6.5 (3x)
8 Fillister head screw M3x8 (4x)9 On-board monitor complete (wide screen)10 On-board monitor trim11 Double insulation-piercing connector (3x)12 Speed nut 4.2 mm (2x)13 Fillister head self-tapping screw with washer 4.2x19 (x2)14 Hexagonal nut with washer M6 (6x)15 On-board monitor radio
053 0002 B
1 4
2 5
6
MODE
FM AM
3
MENU
INFO
TONE SELECT
1
2
49
1110 12 13 14
5 6
15
7 8
3
8/20/2019 X5 Navigation Retrofit
7/37
EN/5
Retrofit / Installation kit No. 65 90 0 136 497 (others see cover sheet) Issue date: 09.2001 Installation Instructions No. 01 29 0 136 499
2. Parts list
000
000
16 Amplifier holder
17 Front base holder18 Rear base holder19 Navigation computer holder20 Navigation computer21 Hexagonal nut with washer M522 Hexagonal screw with washer M5x14 (9x)23 Speed nut M5 (8x)24 Hexagonal screw with washer M6x12 (3x)25 Rubber grommet (2x)26 Removal bar (2x)27 Cable tie (20x)28 Protective strip (3x)
29 Butt-joint connector (7x) (for cable cross-section 0.2 – 0.5 mm
2
)*30 Butt-joint connector (10x) (for cable cross-section 0.75 -1.0 mm
2
)*31 Butt-joint connector (4x) (for cable cross-section 1.5 -2.5 mm
2
)*32 Hose (20x) *33 Fabric tape *
The parts marked with an asterisk (*) are only required for cars with a production dateafter 10/00 (cars with a new generation radio connection plug).
053 0003 B
16 17 18
20
19
21 22 23 24
28 29 30 31 32 33
25 26 27
8/20/2019 X5 Navigation Retrofit
8/37
EN/6
Retrofit / Installation kit No. 65 90 0 136 497 (others see cover sheet) Issue date: 09.2001 Installation Instructions No. 01 29 0 136 499
3. Connection diagram
0
Item DescriptionCable
colourConnection location in the car
A On-board monitor wiring harness
- -
A1
Blue 12-pin socket casing - To blue 12-pin plug casing on the on-board monitor (9)
A2
White 12-pin socket casing - To white 12-pin plug casing on the on-board monitor (9)
A3
Black 17-pin plug casing -
Cars with a production date before 10/00
To radio connection plug X18126
Cars with a production date after 10/00 to be cut
A4
Reversing light socket contact terminal blue/yellow To black 54-pin light module connection plug X10117
in
PIN38;
if PIN38 is occupied cut off the socket contact
and connect the free cable end to the supply cable,
blue/yellow cable, PIN38
on the black 54-pin socket
casing X10117
on the light module using a double
insulation-piercing connector.
A5
Free cable end brown/red To the supply cable, brown/red cable, PIN1
on the blue
26-pin socket casing X10114
on the instrument cluster
using a double insulation-piercing connector
A6*
TAA socket contact terminal black/white To white 18-pin instrument cluster connection plugX10113
in PIN3;
if PIN3 is occupied cut off the socket
contact and connect the free cable end to the supply
cable, black/white cable, PIN3
on the white 18-pin
socket casing X10113
on the instrument cluster using a
double insulation-piercing connector.
A7
Coaxial socket casing black To the coaxial plug casing on the aerial amplifier above
the left wheel arch
A8
Coaxial socket casing black To be laid to the installation location of the left TV
amplifier above the left wheel arch and tied back
A9
Coaxial socket casing black To the coaxial socket casing on the aerial amplifier
above the left wheel arch
A10
Cable eyelet, 6 mm in diameter brown To earth post X13016
after the left wheel arch
A11
Angled coaxial socket casing black To be laid to the installation location of the right TVamplifier above the right wheel arch and tied back
A11
A8A7
A9
A10
A12
A13
A14
A15
A18A19
A20A24
A23A22
A21 A17
A16
A1
A2
A3
A4
A5 A6
A
F 53 0714 B
8/20/2019 X5 Navigation Retrofit
9/37
EN/7
Retrofit / Installation kit No. 65 90 0 136 497 (others see cover sheet) Issue date: 09.2001 Installation Instructions No. 01 29 0 136 499
3. Connection diagram
Item DescriptionCable
colourConnection location in the car
A12
Black 17-pin socket casing - To the on-board monitor radio (15)
A13
10-pin socket casing - To be clipped into the black 17-pin socket casing A12
and connected with it to the on-board monitor radio (15)
A14
Black angled coaxial socket casing
(aerial connector)
black To the coaxial plug casing on the on-board monitor (15)
(aerial connector)
A15
Angled coaxial socket casing black To the coaxial plug casing on the on-board monitor (15)
A16
White 18-pin socket casing - To be tied back on the on-board monitor wiring harness
A
with a cable tie
A17
Blue 18-pin socket casing - To branch A18,
blue 18-pin plug casing on the on-board
monitor wiring harness A
A18
Blue 18-pin plug casing - To branch A17,
blue 18-pin socket casing on the on-
board monitor wiring harness A
A19
Coaxial socket casing black To be tied back on the on-board monitor wiring harness
A
with a cable tie
A20
Coaxial socket casing black To be tied back on the on-board monitor wiring harness
A
with a cable tie
A21
Black 6-pin plug casing - If the car is fitted with a basic interface telephone 2
(BIT2), connect to the black 6-pin socket casing on the
basic interface telephone 2 (BIT2) wiring harness.
If the car is not fitted with a basic interface telephone 2
(BIT2), insulate and tie back.
A22
Blue 18-pin socket casing
(with“Navi” sticker)
- To blue 18-pin plug casing on the navigation computer
(20)
A23
Bordeaux 18-pin socket casing - To Bordeaux 18-pin plug casing on the navigation
computer (20)
A24
Blue 18-pin socket casing
(with“Navi+TV” sticker)
- To be tied back on the on-board monitor wiring harness
A
with a cable tie
8/20/2019 X5 Navigation Retrofit
10/37
EN/8
Retrofit / Installation kit No. 65 90 0 136 497 (others see cover sheet) Issue date: 09.2001 Installation Instructions No. 01 29 0 136 499
3. Connection diagram
0
0
Item DescriptionCable
colourConnection location in the car
B Aerial extension for GPS aerial - -
B1
Coaxial socket casing black To GPS aerial (3)
B2
Coaxial socket casing black To the navigation computer (20)
B
B1 B2
F 53 0803 B
8/20/2019 X5 Navigation Retrofit
11/37
EN/9
Retrofit / Installation kit No. 65 90 0 136 497 (others see cover sheet) Issue date: 09.2001 Installation Instructions No. 01 29 0 136 499
4. Installation and cabling diagram for the on-board monitor wiring harness
0
The on-board monitor wiring harness A is to be laid along the audio or main wiring harness and
secured with cable ties as shown in the figure.
When installing the on-board monitor wiring harness A, start at the earth post X13016above the left wheel arch.
Screw branch A10 to earth post X13016 above the left wheel archLay branch A8 to the intended installation location for the left TV amplifier above the left wheelarch and tie it back (only to be connected if you are also installing a video module and the TVamplifier)Branch A21 to the installation location of the telephone in the rear left side partBranches A22 to A24 to the installation location of the navigation computer in the rear left sidepart
Branches A11 to A20 along the closing panel from the left to the right side of the carLay branch A11 to the intended installation location for the right TV amplifier above the rightwheel arch and tie it back (only to be connected if you are also installing a video module and theTV amplifier)Branches A16 to A20 to the intended installation location of the video module in the multi-purpose tray below the spare wheel and tie it back (only to be connected if you are also installinga video module and TV amplifier)Branch A12 to A15 to the installation location of the on-board monitor radio in the multi-purposetray under the spare wheelBranches A7 and A9 to the aerial amplifier above the left wheel arch
053 0004 B
A11
A
A3
A5
A6
A1
A2
A13
A10
A14
A15A12
A16A19
A7
A20
A17+A18
A8X13016
A21A24
A22
A23A9
A4
RHD A5
RHD A4
RHD A6
8/20/2019 X5 Navigation Retrofit
12/37
EN/10Retrofit / Installation kit No. 65 90 0 136 497 (others see cover sheet) Issue date: 09.2001 Installation Instructions No. 01 29 0 136 499
4. Installation and cabling diagram for the on-board monitor wiring harness
Branches A1 to A3 to the installation location of the on-board monitor in the instrument panelBranch A4 to the installation location of the light module in the A pillar on the bottom right inLHD cars or on the bottom left in RHD carsBranches A5 and A6 to the installation location of the instrument cluster in the instrument panel
Tie back any excess lengths.
The on-board monitor wiring harness A runs along the main wiring harness in front of therear seat bench to the cardan tunnel and from there to the left of the cardan tunnel towardsthe front behind the instrument panel to the installation location of the on-board monitorwhere it is fastened with cable ties or textile adhesive strip."
8/20/2019 X5 Navigation Retrofit
13/37
EN/11Retrofit / Installation kit No. 65 90 0 136 497 (others see cover sheet) Issue date: 09.2001 Installation Instructions No. 01 29 0 136 499
5. To prepare the module holder in the instrument panel for the installation ofthe on-board monitor
0
0
0
0
The figure shows the radio module holder in theinstrument panel."
Cut the radio module holder (40) at the marked
places using a pneumatic saw and remove thearea shaded grey (41).
When sawing with the pneumatic saw or theoscillating saw, extract the chips with a dustextractor and take care that you do notdamage anything in the car (instrument panel,cables, heating box, etc.). It is essential tokeep to the following work sequence."
0
The figure shows another cut in the radiomodule holder on the left. Proceed in exactly
the same way on the right."
Cut out the area shaded grey on the radio moduleholder (40) with an oscillating saw.
Dimension a = 6.5 mm
As you remove this section ensure that only thelateral rib (42) on the rear strut (41) is cut todimension a.
0
Mark the parts on the radio module holder (40) thatyou wish to remove at the top with dimensions a and b.Then, using an oscillating saw, cut into the markedplaces at the side and carefully break them off withpliers.
Dimension a = 20 mmDimension b = 7.5 mm
0
Mark the reinforcement (40), area shaded grey, onthe radio module holder (41) with the dimension a and remove it with an oscillating saw.
Dimension a = 15 mm
F 53 0716 B
41
40
053 0040 B
40
a42
41
a
b b 053 0041 B
40
053 0042 B
41
40
a a
8/20/2019 X5 Navigation Retrofit
14/37
EN/12Retrofit / Installation kit No. 65 90 0 136 497 (others see cover sheet) Issue date: 09.2001 Installation Instructions No. 01 29 0 136 499
5. To prepare the module holder in the instrument panel for the installation of the on-board monitor
0
Before you install the holder for the on-boardmonitor, carefully remove the reinforcements (40)shaded grey on the radio module holder (41) onthe right with an oscillating saw.
0
Carefully remove the reinforcements (40) shadedgrey on the radio module holder (41) on the leftusing an oscillating.
After removing the reinforcement (40) all thecuts on the radio module holder (41) are to bedeburred with a file."
0
Place the top on-board monitor holder (4) into the
removed radio module holder (40) (push it right tothe back).Mark the three mounting points (41) from below and remove the top on-board monitor holder (4)again.Carefully drill the marked mounting points (41) inthe radio module holder (40) with an angled drillusing a 3.5 mm drill bit.
Then slightly countersink the three holes fromabove.
0
Insert the top on-board monitor holder (4) andsecure it to the radio module holder (40) with threeself-tapping screws 3.5 x 6.5 mm (7) using atorque of 2Nm from above.
053 0005 B053 0005 B
41
40
41
053 0005 B053 0006 B
40
4141
4
053 0007 B
4041
4
053 0008 B
40
7
8/20/2019 X5 Navigation Retrofit
15/37
EN/13Retrofit / Installation kit No. 65 90 0 136 497 (others see cover sheet) Issue date: 09.2001 Installation Instructions No. 01 29 0 136 499
5. To prepare the module holder in the instrument panel for the installation of the on-boardmonitor0
0
0
Carefully cut the cross strut (40) off the radiomodule holder (41) along the top on-board monitorholder (4) using an oscillating saw.As you do so ensure that the top on-board monitorholder (4) is not damaged.Deburr the cross strut (40) using a file and placethe two speed nuts 4.2 mm (12) on the top on-board monitor holder (4) from below.
Then unscrew the two Philips self-tapping screws(42) in the radio module holder (41).
0
Place the left on-board monitor holder (5) and theright on-board monitor holder (6) into the cut outradio module holder (40).
0
Secure the left on-board monitor holder (5) and theright on-board monitor holder (6) with one fillisterhead self-tapping screw with washer 4.2 x 19 (13)each to the speed nuts 4.2 mm (12) on the top on-board monitor holder (4) and with the Philips self-tapping screws (40) you removed earlier to the cut-out radio module holder (41).
053 0009 B
40
12 12
4
41
42
053 0034 B
40
5 6
053 0035 B
412
12
5
13
40 40
13
641
8/20/2019 X5 Navigation Retrofit
16/37
EN/14Retrofit / Installation kit No. 65 90 0 136 497 (others see cover sheet) Issue date: 09.2001 Installation Instructions No. 01 29 0 136 499
6. To install the on-board monitor wiring harness and the on-board monitor incars with a production date before 10/00 (cars without a new generation radioconnection plug)
0
0
0
The figure shows the rear left of the bootabove the left wheel arch."
Screw branch A10, cable eyelet, 6 mm in diameter
on the on-board monitor wiring harness A, to earthpost X13016 above the left wheel arch.Lay branches A1 to A6 along the standard wiringharness towards the front, left near the centreconsole and secure it with cable ties.
0
Unscrew the existing coaxial plug casing (40) fromthe aerial amplifier (41) and tie it back (no longerrequired).Screw branch A9, coaxial plug casing on the on-board monitor wiring harness A to the releasedcoaxial socket casing (42) on the aerial amplifier(41).Disconnect the existing coaxial socket casing (43)from the aerial amplifier (41) and tie it back (nolonger required).Connect branch A7, coaxial socket casing to thereleased coaxial plug casing (44) on the aerialamplifier (41).Tie back branch A8, angled coaxial socket casing
(only to be connected if you are also installing thevideo module and the TV amplifier).
F 53 0725 B
A10
X13016
A
A1-A6
F 53 0726 B
40
A7 A9
A8
42
41
43
44
A
8/20/2019 X5 Navigation Retrofit
17/37
EN/15Retrofit / Installation kit No. 65 90 0 136 497 (others see cover sheet) Issue date: 09.2001 Installation Instructions No. 01 29 0 136 499
6. To install the on-board monitor wiring harness and the on-board monitor in cars with aproduction date before 10/00 (cars without a new generation radio connection plug)
0
0
The figure shows the left footwell (LHD car),proceed in exactly the same way on RHDcars."
Carefully cut the carpet (40), as shown in thefigure, using a universal knife to make it easier tolay the on-board monitor wiring harness A.
When you cut the carpet ensure that you donot damage the cables/lines beneath it."
Lay branches A1 to A6 to the installation locationof the on-board monitor and secure them withcable ties.Lay branches A5 and A6 to the installation locationof the instrument cluster and secure them withcable ties.
On LHD cars lay branch A4 behind the glovecompartment to the installation location of thelight module in the A pillar on the bottom rightand secure it with cable ties.
On RHD cars lay branch A4 behind the glovecompartment to the installation location of thelight module in the A pillar on the bottom leftand secure it with cable ties.
0
Connect branch A3, black 17-pin plug casing onthe on-board monitor wiring harness A, to the
existing radio connection plug X18126.Affix a protective strip (28) to the second protectivestrip (28) and then affix them to the wiring harnessso that they enclose the existing angled coaxialsocket casing (40), the black coaxial socket casing(41) (aerial connection), the connection plug for thecontrol (42) and the plug connection A3+X18126.The enclosed connections and the plugconnection are no longer required and are to beplaced behind the heating control.
40
AA1-A6
F 53 0727 B
A3
A
4142
X18126
40
28
28
053 0010 B
8/20/2019 X5 Navigation Retrofit
18/37
EN/16Retrofit / Installation kit No. 65 90 0 136 497 (others see cover sheet) Issue date: 09.2001 Installation Instructions No. 01 29 0 136 499
6. To install the on-board monitor wiring harness and the on-board monitor in cars with aproduction date before 10/00 (cars without a new generation radio connection plug)
00000000000000000000000000000000000000000000000
0
The figure shows installation location of theinstrument cluster."
Connect branch A5, free cable end, brown/redcable, on the on-board monitor wiring harness A,
to the DFAHL signal, brown/red cable, PIN1 on theconnection plug X10114 using a doubleinsulation-piercing connector (10).
0
Connect branch A6, socket contact, black/whitecable on the on-board monitor wiring harness A tothe free slot PIN3 on the white connection plugX10113.If PIN3 on connection plug X10113 is occupied,cut off the socket contact on branch A6 andconnect it to the tacho A signal, black/white cable,PIN3 on the white connection plug X10113 usinga double insulation-piercing connector (11).
0
The figure shows the removed light module onthe bottom right A pillar (LHD cars), on RHDcars proceed in exactly the same way on thebottom left A pillar."
Remove the light module (40), and disconnect theblack 54-pin socket casing X10117 from the lightmodule (40).Connect branch A4, socket contact, blue/yellowcable on the on-board monitor wiring harness A tothe free slot PIN38 on socket casing X10117.If PIN38 on socket casing X10117 is occupied, cutoff the socket contact on branch A4 and connect
it to the reversing light signal, blue/yellow cable,PIN38 on socket casing X10117 using a doubleinsulation-piercing connector.
Then connect socket casing X10117 and installthe light module (40) again.Tie back any excess lengths of branch A4.
053 0011 B
A5
A
X10114
11
A5A
X10114
053 0012B
A6
11
A
X10113
40
X10117
A411
053 0013 B
8/20/2019 X5 Navigation Retrofit
19/37
EN/17Retrofit / Installation kit No. 65 90 0 136 497 (others see cover sheet) Issue date: 09.2001 Installation Instructions No. 01 29 0 136 499
6. To install the on-board monitor wiring harness and the on-board monitor in cars with aproduction date before 10/00 (cars without a new generation radio connection plug)
0
0
Connect branch A1,, blue 12-pin socket casing onthe on-board monitor wiring harness A, to the on-board monitor (9).Connect branch A2,, white 12-pin socket casingto the on-board monitor (9).
Then insert the cables into the radio module holder(40) and carefully slide the on-board monitor (9)into position.
As you insert the holder ensure that nocables/leads are damaged."
0
Secure the on-board monitor (9) using four fillisterhead screws M3x8 (8) to the on-board monitorholder on the left (5) and the on-board monitorholder on the right (6).
The insert the trim for the on-board monitor (10) onto the on-board monitor (9).
0
The figure shows the boot at the rear left."
Lay branches A21 to A24 on the on-board wiringharness A to the installation location of thenavigation computer.Bei Fahrzeugen die mit Basis-Interface-Telefon 2(BIT2) ausgestattet sind, den Abzweig A21,schwarzes 6poliges Stiftgehäuse, mit demschwarzen 6poligen Buchsengehäuse des Basis-Interface-Telefonkabelbaums (BIT2) zusammen-stecken.If the car does not have a basic interfacetelephone 2 (BIT2), insulate and tie back branch
A21.Lay branches A11 to A20 along the standardwiring harness through the cable shaft on theclosing panel to the right-hand side of the car andsecure them with cable ties.
053 0036 B
A2
A1
9
40
053 0037 B
9
65
8
8
8
810
F 53 0733 B
A21
A22A23
A
A24
A11-A20
8/20/2019 X5 Navigation Retrofit
20/37
EN/18Retrofit / Installation kit No. 65 90 0 136 497 (others see cover sheet) Issue date: 09.2001 Installation Instructions No. 01 29 0 136 499
6. To install the on-board monitor wiring harness and the on-board monitor in cars with aproduction date before 10/00 (cars without a new generation radio connection plug)
0
Lay branch A11,, angled coaxial socket casing onthe on-board wiring harness A, along the standardwiring harness (40) to the right wheel arch, secureit with cable ties and tie it back (only to beconnected if you are also installing a video module
and the TV amplifier).Lay branches A12 to A15 to the unit holder (41) inthe multi-purpose tray (42) and secure them withcable ties.
0
Lay branches A16 to A20 on the on-board monitor
wiring harness A to the unit holder (40) in the multi-purpose tray (41) and secure them with cable ties.
F 53 0734 B
A11
A
41
42
40
A12
A13A14
A15
053 0014 BA
40
41
A20
A19
A17/A18
A16
8/20/2019 X5 Navigation Retrofit
21/37
EN/19Retrofit / Installation kit No. 65 90 0 136 497 (others see cover sheet) Issue date: 09.2001 Installation Instructions No. 01 29 0 136 499
7. To install the on-board monitor wiring harness and the on-board monitor incars with a production date after 10/00 (cars with a new generation radioconnection plug)
0
The figure shows the rear left of the bootabove the left wheel arch."
Screw branch A10, cable eyelet, 6 mm in diameter
on the on-board monitor wiring harness A, to earthpost X13016 above the left wheel arch.Lay branches A1 to A6 along the standard wiringharness towards the front, left near the centreconsole and secure it with cable ties.
0
Disconnect the cables from the existing aerial
amplifier (40) and remove the existing aerialamplifier (40).Then install the new aerial amplifier for cars with aproduction date before 10/00, which you orderedseparately using the electronic parts catalogue(EPC), and connect it following procedure for itsremoval in reverse.
As you connect it ensure that you do not mixup the slots."
0
Unscrew the existing coaxial plug casing (40) fromthe aerial amplifier (41) and tie it back (no longerrequired).Screw branch A9, coaxial plug casing on the on-board monitor wiring harness A to the releasedcoaxial socket casing (42) on the aerial amplifier(41).Connect branch A7, coaxial socket casing, to thefree coaxial plug casing (43) on the aerial amplifier(41).
Tie back branch A8, angled coaxial socket casing(only to be connected if you are also installing thevideo module and the TV amplifier).
F 53 0725 B
A10
X13016
A
A1-A6
F 53 0840 B
40
A
F 53 0839 B
40
A7A9
A8
42
41
43
A
8/20/2019 X5 Navigation Retrofit
22/37
EN/20Retrofit / Installation kit No. 65 90 0 136 497 (others see cover sheet) Issue date: 09.2001 Installation Instructions No. 01 29 0 136 499
7. To install the on-board monitor wiring harness and the on-board monitor in cars with aproduction date after 10/00 (cars with a new generation radio connection plug)
0
The figure shows the left footwell (LHD car),proceed in exactly the same way on RHDcars."
Carefully cut the carpet (40), as shown in thefigure, using a universal knife to make it easier tolay the on-board monitor wiring harness A.
When you cut the carpet ensure that you donot damage the cables/lines beneath it."
Lay branches A1 to A6 to the installation locationof the on-board monitor and secure them withcable ties.Lay branches A5 and A6 to the installation locationof the instrument cluster and secure them with
cable ties.
For LHD carsLay branch A4 behind the glove compartment tothe installation location of the light module in thebottom right A pillar and secure it with cable ties.
For RHD carsLay branch A4 behind the glove compartment tothe installation location of the light module in thebottom left A pillar and secure it with cable ties.
0
The figure shows installation location of theinstrument cluster."
Connect branch A5, free cable end, brown/redcable, on the on-board monitor wiring harness A,to the DFAHL signal, brown/red cable, PIN1 on theconnection plug X10114 using a doubleinsulation-piercing connector (10).
40
AA1-A6
F 53 0727 B
053 0015 B
A5
A
X10114
11
A5A
X10114
8/20/2019 X5 Navigation Retrofit
23/37
EN/21Retrofit / Installation kit No. 65 90 0 136 497 (others see cover sheet) Issue date: 09.2001 Installation Instructions No. 01 29 0 136 499
7. To install the on-board monitor wiring harness and the on-board monitor in cars witha production date after 10/00 (cars with a new generation radio connection plug)
0
Connect branch A6, socket contact, black/whitecable on the on-board monitor wiring harness A tothe free slot PIN3 on the white connection plugX10113.If PIN3 on connection plug X10113 is occupied,
cut off the socket contact on branch A6 andconnect it to the tacho A signal, black/white cable,PIN3 on the white connection plug X10113 usinga double insulation-piercing connector (11).
0
The figure shows the removed light module onthe bottom right A pillar (LHD cars), on RHDcars proceed in exactly the same way on thebottom left A pillar."
Remove the light module (40), and disconnect theblack 54-pin socket casing X10117 from the lightmodule (40).Connect branch A4, socket contact, blue/yellowcable on the on-board monitor wiring harness A tothe free slot PIN38 on socket casing X10117.If PIN38 on socket casing X10117 is occupied, cutoff the socket contact on branch A4 and connectit to the reversing light signal, blue/yellow cable,PIN38 on socket casing X10117 using a doubleinsulation-piercing connector.
Then connect socket casing X10117 and installthe light module (40) again.Tie back any excess lengths of branch A4.
0
Carefully remove the sheathing on the on-boardmonitor wiring harness A over a length of 100 mmbehind branch A3.
Then carefully remove the sheathing on the audiowiring harness (40) over a length of 100 mmbehind the new generation radio connector (41).
053 0016 B
A6
11
A
X10113
40
X10117
A411
053 0017 B
A3
A40
41053 0043 B
8/20/2019 X5 Navigation Retrofit
24/37
EN/22Retrofit / Installation kit No. 65 90 0 136 497 (others see cover sheet) Issue date: 09.2001 Installation Instructions No. 01 29 0 136 499
7. To install the on-board monitor wiring harness and the on-board monitor in cars with aproduction date after 10/00 (cars with a new generation radio connection plug)
Cut the yellow/red connection cable, RADLV+, PIN1 on branch A3 and the yellow/redconnection cable, RADLV+, PIN3 on the new generation radio connection plug (40) with anangle cutter.Push the hose (32) on to the cut yellow/red connection cable (42) on the on-board monitor wiringharness A.Then connect the cut yellow/red connection cable (42) on the on-board monitor wiring harnessA and the cut yellow/red connection cable (43) on the audio wiring harness (41) with a butt-jointconnector (30) (cable cross section 0.75-1.00 mm 2).Push the hose (32) over the crimped butt-joint connector (30) and shrink it on with a hot airblower.Cut the black/white connection cable, tacho A signal, PIN10 on branch A3 with an angle cutter.Put the hose (32) on to the cut black/white connection cable (44) on the on-board monitor wiring
harness A, and shrink it using a hot air blower so that the open cable end is insulated (notrequired).
Then connect the remaining connection cables on branch A3 as set out in the followingfollowing connection table to the connection cables on the new generation radio connectionplug (40).
When you have made all the connections, first wrap each individual connection and then all theconnections in the fabric tape (33) (cut branch A3 is no longer required).
The figure shows branch A3, black 17-pin plug casing on the on-board monitor wiringharness A and the new generation radio connection plug (40) on the audio wiring harness(41) when removed, if they are fitted, proceed in exactly the same way."
Always complete one connection at a time since if you cut several connection cables youmight confuse them as a result of the different cable colours involved (see followingconnection table). In addition. ensure that you use the appropriate butt-joint connectors forthe various cable cross-sections."
41 40
43 33 44
A3
A30
32 42
PIN3
PIN1
PIN10 053 0018 B
8/20/2019 X5 Navigation Retrofit
25/37
EN/23Retrofit / Installation kit No. 65 90 0 136 497 (others see cover sheet) Issue date: 09.2001 Installation Instructions No. 01 29 0 136 499
7. To install the on-board monitor wiring harness and the on-board monitor in cars with aproduction date after 10/00 (cars with a new generation radio connection plug)
Connection table (on-board monitor wiring harness to the audio wiring harness)
New generation radio connection plug (40) onthe audio wiring harness
Branch A3 on the on-board monitor wiringharness
X18805 X18126
PIN Signal Cable colourCross-
sectionPIN Signal Cable colour
Cross-
section
3 RADLV+ GERT 0.75 mm2 1 RADLV+ GERT 0.75 mm2
1 RADRH+ BLVI or BLSW or free 0.75 mm2 6 RADRH+ BLSW 0.75 mm2
2 RADRV+ BLRT 0.75 mm2 2 RADRV+ BLRT 0.75 mm2
4 RADLH+ GEVI or GESW or free 0.75 mm2 3 RADLH+ GESW 0.75 mm2
5 RADRH- BLGR or BROR or free 0.75 mm2 14 RADRH- BROR 0.75 mm2
6 RADRV- BLBR or BROR 0.75 mm2 11 RADRV- BROR 0.75 mm2
7 RADLV- GEBR or BROR 0.75 mm2 8 RADLV- BROR 0.75 mm2
8 RADLH- GEGR or BROR or free 0.75 mm2 12 RADLH- BROR 0.75 mm2
X18126 X18126
9 I/K bus WSGRGE 0.35 mm2 7 I bus WSGRGE 0.35 mm2
10 TELM WSBR 0.35 mm2 4 TELM WSBR 0.35 mm2
13 ANT WS 0.50 mm2 16 ANT WS 0.50 mm2
14 58G GRRT 0.50 mm2 13 58G GRRT 0.50 mm2
15 30
8/20/2019 X5 Navigation Retrofit
26/37
EN/24Retrofit / Installation kit No. 65 90 0 136 497 (others see cover sheet) Issue date: 09.2001 Installation Instructions No. 01 29 0 136 499
7. To install the on-board monitor wiring harness and the on-board monitor in cars with aproduction date after 10/00 (cars with a new generation radio connection plug)
0
0
0
Disconnect the white 12-pole connector X13321 from the new generation radio connection plug(40).Then cut the remaining connection cables on thenew generation radio connection plug (40) with anangle cutter and insulate the open cable ends (thecut-off new generation radio connection plug (40)is no longer required).
0
Affix one rattle guard (28) on to the second rattleguard (28) and then affix them to the wiringharness so that the angled Fakra plug (aerial
connector) (40), the connection plug for the control(41), connection plug X13321 and the wrappedconnections (42) are enclosed in them.The wrapped connections (40, 41 and X13321)and the wrapped connectors (42) are no longerrequired and should be placed behind the heatingsystem control.
0
Connect branch A1,, blue 12-pin socket casing onthe on-board monitor wiring harness A, to the on-board monitor (9).Connect branch A2,, white 12-pin socket casingto the on-board monitor (9).Then insert the cables into the prepared radiomodule holder (40) and carefully slide the on-board monitor (9) into position.
As you insert the holder ensure that nocables/leads are damaged."
0
Secure the on-board monitor (9) using four fillisterhead screws M3x8 (8) to the on-board monitorholder on the left (5) and the on-board monitorholder on the right (6).The insert the trim for the on-board monitor (10) onto the on-board monitor (9).
A
40
40
40
X13321
053 0019 B
42
X13321
40
28
28
A 41
053 0020 B
053 0036 B
A2
A1
9
40
053 0037 B
9
65
8
8
8
810
8/20/2019 X5 Navigation Retrofit
27/37
EN/25Retrofit / Installation kit No. 65 90 0 136 497 (others see cover sheet) Issue date: 09.2001 Installation Instructions No. 01 29 0 136 499
7. To install the on-board monitor wiring harness and the on-board monitor in cars with aproduction date after 10/00 (cars with a new generation radio connection plug)
0
0
0
The figure shows the boot at the rear left."
Lay branches A21 to A24 on the on-board wiringharness A to the installation location of thenavigation computer.On cars with a basic interface telephone 2 (BIT2),connect branch A21, black 6-pin plug casing, tothe black 6-pin socket casing on the basicinterface telephone wiring harness (BIT2).If the car does not have a basic interfacetelephone 2 (BIT2), insulate and tie back branchA21.Lay branches A11 to A20 along the standardwiring harness through the cable shaft on theclosing panel to the right-hand side of the car andsecure them with cable ties.
0
Lay branchA11,
, angled coaxial socket casing onthe on-board wiring harness A, along the standardwiring harness (40) to the right wheel arch, secureit with cable ties and tie it back (only to beconnected if you are also installing a video moduleand the TV amplifier).Lay branches A12 to A15 to the unit holder (41) inthe multi-purpose tray (42) and secure them withcable ties.
0
Lay branches A16 to A20 on the on-board monitorwiring harness A to the unit holder (40) in the multi-purpose tray (41) and secure them with cable ties.
F 53 0733 B
A21
A22A23
A
A24
A11-A20
F 53 0734 B
A11
A
41
42
40
A12
A13 A14
A15
053 0023 BA
40
41
A20
A19
A17/A18
A16
8/20/2019 X5 Navigation Retrofit
28/37
EN/26Retrofit / Installation kit No. 65 90 0 136 497 (others see cover sheet) Issue date: 09.2001 Installation Instructions No. 01 29 0 136 499
8. To install the on-board monitor radio0
The figure shows the multi-purpose tray in theboot."
If the two rubber grommets (40) are not fitted in theunit holder (41), the two rubber grommets (25)supplied in the retrofit/installation kit must be
fitted.Then insert the on-board monitor radio (15) intothe rubber grommets (40/25) as shown in thefigure.
0
Remove the blue locking clip (40) from branchA12, black 17-pin socket casing on the on-boardmonitor wiring harness A and connect branchA13, 10-pin socket casing, to branch A12 in theappropriate position.
On cars with a CD changer but without a DSPamplifier, the control cable for the on-boardmonitor wiring radio/CD changer must also befitted."
Secure branch cable A13 with the blue locking clip(40).Connect branch cable A12, black 17-pole socketcasing, to on-board monitor radio (15).Connect branch A14, black angled coaxial socketcasing (aerial connection), to the on-board monitor
radio (14).Connect branch cable A15, angled coaxial socketcasing, to the on-board monitor radio (15).
0
Secure the on-board monitor radio (15) to the unitholder (40) using the hexagonal nut with washerM5 (21) or hexagonal screw with washer M5x14mm (22), depending on the design of the on-boardmonitor radio (15).Affix the rattle guard (28) to the on-board monitorwiring harness A so that branches A19 and A20,plug connection A17+A18 and branch A16 arewrapped in it.
Tie back the wrapped connections and the plugconnector to the standard wiring harness (41) inthe multi-purpose tray (42) (only to be connected ifyou are also installing the video module and the TVamplifiers).
053 0024 B40
15
41
25
053 0025 B
A
15
40A13 A14
A15
A12
053 0026 B
15
21 22
28
40 41
A
42
A19 A16A17/A18
A20
8/20/2019 X5 Navigation Retrofit
29/37
EN/27Retrofit / Installation kit No. 65 90 0 136 497 (others see cover sheet) Issue date: 09.2001 Installation Instructions No. 01 29 0 136 499
9. To install audio module holder (only required in cars without an audio moduleholder)
0
0
0
The figure shows the boot at the rear left."
Place amplifier holder (16) on the two bottom studbolts (40) and the two side stud bolts (41).
0
Secure the amplifier holder (16) to the stud bolts(40) using two hexagonal nuts with washers M6(14) and to the M6 thread (41) in the inside closing
panel (42) using a hexagonal screw with washerM6x12 (24).Then place two speed nuts M5 (23) on theamplifier holder (16).
0
Place the front base holder (17) on to the two sidestud bolts (40) and secure it to the stud bolts (40)with two hexagonal nuts with washers M6 (14).In addition, secure the front base holder (17) to thethread M6 (41) in the rear left side part (42) using ahexagonal screw with washer M6x12 (24).Then place two speed nuts M5 (23) on the frontbase holder (17).
0
Secure the rear base holder (18) to the speed nutsM5 (23) that you positioned earlier using fourhexagonal screws with washers M5x14 (22) and tothe thread M6 (30) in the side part at the rear left(41) using a hexagonal screw with washer M6x12(24).Then place two speed nuts M5 (23) on to the frontbase holder (17) and the rear base holder (18).
053 0027 B
41
40
16
053 0028 B
16
14
40
23
42
41
24
053 0029 B
17
40
24
4123
1414
42
053 0030 B
17
23
22
23
22
2423
18
23
4140
8/20/2019 X5 Navigation Retrofit
30/37
EN/28Retrofit / Installation kit No. 65 90 0 136 497 (others see cover sheet) Issue date: 09.2001 Installation Instructions No. 01 29 0 136 499
10. To install the navigation system0
0
0
The figure shows the tailgate under the rearspoiler from the outside."
Put GPS antenna (3) on the two stud bolts (40) onthe boot lid (41) and secure it with two hexagonal
nuts with washers M6 (14).Thread the connection cable (42) for the GPSaerial (3) through the opening in the tailgate (41)into the interior of the car and fit the rubbergrommet (43).
0
Connect branch B1, coaxial plug casing on theaerial extension for the GPS aerial B to the coaxialsocket casing (40) on the connection cable (41) forthe GPS aerial.
Then thread the aerial extension for the GPS aerialB with branch B2, coaxial socket casing, throughthe rubber grommet (42), as show in the figure,into the interior of the car and secure it with textileadhesive tape (43).
0
Lay the aerial extension for the GPS aerial B with
branch B2, coaxial socket casing, along thestandard wiring harness as shown in the figure tothe installation site of the navigation computer inthe boot at the rear left and secure it with textileadhesive tape or cable ties.
053 0031 B
340
14 14
40 42
41
43
F 53 0739 B
B1B 40
B2
41
43
42
F 53 0847 B
B2
B
8/20/2019 X5 Navigation Retrofit
31/37
EN/29Retrofit / Installation kit No. 65 90 0 136 497 (others see cover sheet) Issue date: 09.2001 Installation Instructions No. 01 29 0 136 499
10. To install the navigation system
0
0
Secure the navigation computer holder (19) to thefour speed nuts M5 (23) you inserted previouslyusing four hexagonal screws with washers M5x14(22).Thread branches A22 and A24 blue 18-pin socketcasing, and branch A23, Bordeaux 18-pin socketcasing on the on-board monitor wiring harness A,
from the rear through the navigation computerholder (19).
Tie back branch A24, with the sticker "NAVI+TV"on branch A22, with the sticker "NAVI" using acable tie.
Push branch cable B2, coaxial socket casing, onthe aerial extension for the GPS aerial B from therear through the navigation computer holder (19)as well.
0
Connect branch A22, blue 18-pin socket casing,
with the sticker “NAVI” and the tied back branchA24 on the on-board monitor wiring harness A tothe navigation computer (20).Connect branch A23, Bordeaux 18-pin socketcasing, to the navigation computer (20).Connect branch B2, coaxial socket casing on theaerial extension for the GPS aerial B2, to thenavigation computer (19).
When you slide in the navigation computer(20) ensure that no cables or lines are jammed
or damaged."
Push the navigation computer (20) into thenavigation computer holder (19) until it engages.
A24
053 0032 B
23
A
B23
22
B222
19
A23
A22
B2
A22 A24
A23
20 053 0033 B
A
B19
8/20/2019 X5 Navigation Retrofit
32/37
EN/30Retrofit / Installation kit No. 65 90 0 136 497 (others see cover sheet) Issue date: 09.2001 Installation Instructions No. 01 29 0 136 499
11. Coding and concluding work
Coding
This system requires coding.
To ensure that the retrofit system:– is fully functional and– does not cause malfunctions and errors in other electrical systems this retrofit system and, possibly, other components must be coded and saved in the centralcode in the IKE.
This coding process is automatic using the current coding program in the “Retrofit” path.The process is user-guided, simply follow the text instructions for each individual step.
Procedure:
- Connect DIS/MoDIC to the car- Switch the ignition “ON”- Select “Coding ZCS”– Confirm the date by pressing “ Y ” (MoDIC only)- Series: “E53”- Path: “2 Retrofit”- System: “Navigation”
- Start automatic coding (confirm with “ Y ”)– Follow the instructions on the on-board monitor
- Print out the new central label for the amended coding key and affix it to the car on the right-hand side of the boot near the battery.- After the message “Coding complete” appears on the monitor of the DIS/MoDIC, switch the
ignition ”OFF”, wait for at least 10 seconds and then switch the ignition “ON” again.- Print out the error memory– Insert the CD-ROM “Road map” into the navigation computer– Complete a function test
If you also wish to install the video module and TV amplifiers for TV function, the coding andthe concluding work should not be completed until after the video module and TVamplifiers for TV function have been installed, see section 13) ."
The current “Navigation CD-ROM operating software V16” is required to load theoperating system.ImportantDo not insert the CD-ROM “Operating software” into the CD drive yet.Do not insert the CD-ROM “Operating software” until asked to do so by the instructionson the on-board monitor.At the same time this CD-ROM “Operating software” also encodes the language."
8/20/2019 X5 Navigation Retrofit
33/37
EN/31Retrofit / Installation kit No. 65 90 0 136 497 (others see cover sheet) Issue date: 09.2001 Installation Instructions No. 01 29 0 136 499
11. Coding and concluding work000
Procedure:
- Connect DIS/MoDIC to the car- Switch the ignition “ON”- Select “Coding ZCS”– Confirm the date by pressing “ Y ” (MoDIC only)- Series: “E53”- Path: “1 Recoding”- System: “DSP”- Start automatic coding (confirm with “ Y ”)- After the message “Coding complete” appears on the monitor of the DIS/MoDIC, switch the
ignition ”OFF”, wait for at least 10 seconds and then switch the ignition “ON” again.
- Print out the error memory– Complete a function test
Language coding
The language coding can be repeated using the “Navigation CD-ROM operating software”.
Concluding work
Connect the batteryConduct a function testAssemble the car again following the instructions to dismantle it in reverse orderPrint out the error memory
In vehicles with a DSP amplifier, the DSP amplifier also has to be recoded."
8/20/2019 X5 Navigation Retrofit
34/37
EN/32Retrofit / Installation kit No. 65 90 0 136 497 (others see cover sheet) Issue date: 09.2001 Installation Instructions No. 01 29 0 136 499
12. Connection description for TV function0
To complete the upgrade the required parts (video module, TV amplifier and small parts) mustbe ordered separately using the electronic parts catalogue (EPC) and installed.
In addition the appropriate branches of the on board monitor wiring harness A must beconnected as follows:
Undo the tied-back branch cable A8, angled coaxial socket casing on the on-board monitorwiring harness A, and connect it on to the left TV amplifier installed previously above the leftwheel arch.Release the tied back branch A11, angled coaxial socket casing on the on-board monitor wiringharness A and connect it to the TV amplifier installed previously above the right wheel arch.Disconnect branch A22, blue 18-pin socket casing with the sticker "NAVI" on the on-boardmonitor wiring harness A from the navigation computer.Release the tied-back branch cable A24, blue 18-pin socket casing with the sticker “NAVI + TV” on the on-board monitor wiring harness A, and connect it to the blue 18-pin plug casing on the
navigation computer.Branch A22, blue 18-pin socket casing with the sticker “NAVI”, which you previouslydisconnected, is to be tied back (not required).Release tied back plug connection A17+A18 on the on-board monitor wiring harness A,disconnect it and connect branch A17 , blue 18-pin plug casing on the on-board monitor wiringharness A, to the blue 18-pin socket casing on the video module, which you previously installedin the multi-purpose tray under the spare wheel.Tie back branch A18, blue 18-pin plug casing on the on-board monitor wiring harness A (no longer required).Also release the tied back branches A19 and A20, coaxial socket casing, and branch A16, white18-pin socket casing on the on-board monitor wiring harness A and connect it to the previouslyinstalled video module in the multi-purpose tray under the spare wheel.Connect branches A19 and A20, coaxial socket casings, to the two coaxial plus casings on thevideo module.Connect branch A16, white 18-pin socket casing, to the white 18-pin plug casing on the videomodule.
This chapter is only applicable if the car is also to be upgraded with the TV function."
If the car is to be upgraded to TV function at a later date, the system will have to be recoded.For further details refer to section “12. Coding and concluding work”..
8/20/2019 X5 Navigation Retrofit
35/37
EN/33Retrofit / Installation kit No. 65 90 0 136 497 (others see cover sheet) Issue date: 09.2001 Installation Instructions No. 01 29 0 136 499
13. Circuit diagram, on-board monitor wiring harness00000
0
A 1 9 7
0 , 3 5
S C H I R M
0 , 3 5
S C H I R M
W
S
W S
W S
V M G
V M R 3 1
V M
R
V M G 3 1
1 4
5
1 6
7
T A P E R +
T A P E L -
T A
P E L +
T A P E R -
2
1
7
6
0 , 5 G E B R
0 , 5 G E R T
V M -
V M +
5
1 0
1 3 8 6 6 9 9 . 9
L T G V E R D R I L L T
1 3 8 6 6 9 8 . 9
L T G V E R D R I L L T
1 7 2 4 0 4 6 . 9
L T G G E S C H .
1 3 8 6 6 9 6 . 9
L T G V E R D R I L L T
T A P E R +
T A P E L -
T A
P E L +
T A P E R -
G N D
R X D
C T S
R T S
T X D
9
1 0
4
3
P L 1
2
5
4
3
2
1 0 , 3 5
S W
0 , 3 5
S C H I R M
0 , 3 5
S W
0 , 3 5
S W
7
6
0 , 5 B R R T
P L 1
2
V M B 3 1
V M B
V M L C 3 1
1 2
1 5
6
V M G
V M R 3 1
V M
R
V M G 3 1
V M B 3 1
V M B
V M L C 3 1
1 7 2 4 2 1 3 . 9
L T G 1 - A D R . G E S C H .
1 7 2 4 2 1 3 . 9
L T G 1 - A D R . G E S C H .
1 7 2 4 2 1 3 . 9
L T G 1 - A D R . G E S C H .
3 0 < 6 4
8
3 0 < 6 4
I / K - B U S
7
6
0 ,
5
R T G N
0 , 5 R T G N
0 , 5 W S G R G E
R < E 1
1
0 , 5 V I W S
5 8 G 1
0 , 5 G R R T
1 0
1 1
3 1 E < R A D
0 , 5 B R
3 1 E < R A D
0 , 5 B R
9
1 8
V M +
V M -
0 , 5 R T G N
3 0 < 6 4
1
0 , 5 R T G N
3 0 < 6 4
2
0 , 5 W S G R G E
I / K - B U S
3
X 1
5 4 3
V B
3 0 R A D I O
-
X 1 8 3 4 4
V B I - B U S
-
X 2 2 9
V B
R
-
X 1 3 6 2
V B
5 8 G
5 8 G
X 1
8 8 0 1
X 1 8 8 0 2
R A D I O
R A D I O
R A D I O
X 1 8 8 0 4
R A D I O
X 1 8 8 0 5
R A D I O
N 9
A
1 9 6
X 1 3 0 1 6
M A S S E S T E R E O / H I F I
-
X 1 8 8 0 4
X 1 8 8 0 2
R A D I O
X 1 3 0 1 6
M A S S E S T E R E O / H I F I
-
R A D I O
B O R D M O N I T O R
V I D E O M O D U L
3 1 E < R A D
2
0 , 7 5
B L S W
0 , 7 5
B R O R
R A D R H
+
R A D R H -
6
1 4
0 , 7 5
G E S W
0 , 7 5
B R O R
R A D L H +
R A D L H -
3
1 2
0 , 7 5
B L R T
0 , 7 5
B R O R
R A D R V +
R A D R V -
2
1 1
0 , 7 5
G E R T
0 , 7 5
B R O R
R A D L V +
R A D L V -
1
8
0 , 5 W S
A N T
1 6
I - B U S
7
R
3 0 < 6 4
5
9
5 8 G 1
3
0 , 3 5
W S G R G E
1 , 5 V I W S
2 , 5 R T G N
0 , 5 G R R T
R A D R H +
R A D R H -
R A D L H +
R A D L H -
R A D R V +
R A D R V -
R A D L V +
R A D L V -
A N T
6
1 4
3
1 2
2
1 1
1
8
1 6
I - B U S
R
3 0 < 6 4
5 8 G
7
5
9
1 3
0 , 3 5
W S G R G E
1 , 5 V I W S
2 , 5 R T G N
0 , 5 G R R T
T A A 1
0
0 , 3 5
S W W S
T A A
1 0
0 , 3 5
S W W S
0 , 3 5
S W W S
1 3 9 3 9 0 6 . 9
L T G V E R D R I L L T
1 3 9 3 9 0 5 . 9
L T G V E R D R I L L T
1 3 9 3 9 0 4 . 9
L T G V E R D R I L L T
1 3 9 3 9 0 3 . 9
L T G V E R D R I L L T
X 1 8 3 4 4
V B
I - B U S
-
X 1 5 4 3
V B
3 0 R A D I O
-
X 2 2 9
V B
R
-
X 1 3 6 2
X 5 8 1
V B
5 8 G
V B T A C H O
A
-
-
X 6 5 0 0 S
R A D I O
R A D I O / H I F I
3 1 E < R A D
1 5
X 1 8 1 2 6
0 , 3 5
W S B R
T E L M
4 T E L M
4
X 1 8 1 2 6
R A D I O
0 , 5 S W
0 , 5
B L S W
0 , 5 B L B R
0 , 5 G E S W
0 , 5 G E B R
0 , 5 B R
0 , 3 5
B L G E
0 , 5 B R
2 , 5 B R
0 , 3 5
B L G E
0 , 3 5
B R R T
R S
0 , 5 S c h i r m
G N D
0 , 5 G E
R X D
0 , 5 S W
C T S
0 , 5 G N
R T S
0 , 5 B R
0 , 7 5
V I / W S
T X D
R
D F A H L
1
1 5 1
2
3
4
5
1 6
1 4
1 3
1 2
3
1 1
X 1 3 1 2 B
R A D I O
X 6 9 9 9 0
X 3 2 7 9
L E I T U N G
O F F E N
-
X 1 3 3 1 8 5
3 0
< 6 4
X 1 8 8 0 1
T A A
1 X 1 0 1 1 3 B
R A D I O
R S 3
8
X 1 0 1 1 7 B
R A D I O
F
5 3 0 8 4 8
BOn-board monitor wiring harness
8/20/2019 X5 Navigation Retrofit
36/37
EN/34Retrofit / Installation kit No. 65 90 0 136 497 (others see cover sheet) Issue date: 09.2001 Installation Instructions No. 01 29 0 136 499
13. Circuit diagram, on-board monitor wiring harness0000
0 , 5 R T G N
0 , 5 R T G N
0 , 3 5
S W
0 , 5 W S G R G E
0 , 3 5
S W
0 , 3 5
S C H I R M
0 , 3 5
S W
0 , 3 5
S C H I R M
0 , 3 5
S C H I R M
3 0 < 6 4
3 0 < 6 4
V M R
I / K - B U S
V M G
V M R 3 1
V M B
V M G 3 1
V M B 3 1
2
1
7
3
5
1 6
6
1 4
1 5
3 1 E < R A D
1 0
3 1 E < R A D
1 1
1
2
V M +
9
V M -
1 8
0 , 7 5
V I W S
0 , 5 R T G N
0 , 5 W S G R G E 0
, 5 B R
1 7 2 4 2 1 3 . 9
L T G 1 - A D R I G G E S C H .
1 7 2 4 2 1 3 . 9
L T G 1 - A D R I G G E S C H .
1 7 2 4 2 1 3 . 9
L T G 1 - A D R I G G E S C H .
1 3 8 6 6 9 6 . 9
L T G V E R D R I L L T
1 8 3 6 5 5 5 3 . 9
R G 1 7 4
X 2 2 9
X 1 8 3 4 4
X 1 5
4 3
V B R
-
V B I - B U S
X 3 2 7 9
V B
3 1
-
V B 3 0
R A D I O
-
0 , 5 B R R T
0 , 5 B R
0 , 5 B R
0 , 5 G E R T
0 , 5 G E B R
0 , 3 5
S C H I R M
S C H I R M
0 , 1 4
S W
V M L C 3 1
3 0 < 6 4
3 0 < 6 4
V M R
I / K - B U S
V M G
V M R 3 1
V M B
V M G 3 1
V M B 3 1
3 1 E < R A D
3 1 E < R A D
V M +
V M -
V M L C 3 1
1 2
3 0
V I W S
I - B U S
3 1
1
3
1 0
1 7 2 4 0 4 6 . 9
L T G G E S C H .
1 3 8 6 6 9 . 7
L T G V E R D R I L L T
R G B G N D
R 7 5
B 7 S
B 7 5
S Y N C
V O I C E
V O I E G N D
R A D I O
0 , 5 S c h i r m
R 7 5
0 , 5 G E
B 7 5
0 , 5 S W
G 7 5
0 , 5 G N
S Y N C
0 , 5 B R
0 , 5 B L R T
0 , 5 B L B R
R G B G N D
V O I C E
V O I E G N D
4 7
1 8
1 7
1 6
8
3
1 2
1 3
8
1 7
1 5
9
1 8
1
2
3
7
1 6
5
1 4
6
1 5
1 2
1 0
1 1
9
1 8
1
2
X 1 3 1 3 B
R A D I O
X 6 5 0 2 B
X 1 3 3 4 6
R A D I O
R A D I O
A 4 5 3
V E R S T Ä R K E R
T V
X 1 8 8 0 6 B
R A D I O
X 6 5 0 1 S
V I D E O M O D U L
S C H I R M
A N T
A N T
A 1
9 7
X 1 3 3 4 8
1
2
1 8 3 6 5 5 5 3 . 9
R G 1 7 4
0 , 3 5
S C H I R M
S C H I R M
0 , 1 4
S W
1
2
X 1 3 3 4 7
R A D I O
A 4 5 3
V E R S T Ä R K E R T V
V I D E O M O D U L
S C H I R M
A U
A N T
A N T
A 1 9 7
X 1 3 3 4 9
1
1 8 3 6 5 5 5 3 . 9
R G 1 7 4
0 , 3 5
S C H I R M
S C H I R M
0 , 1 4
S W
1
2
X 1 3 3 4 4
R A D I O
A 4 2 1
D I V E R S I T Y
R A D I O
A N T - H F
A N T - H F
N 9
X 1 3 3 4 2
1
2
1 8 3 6 5 5 5 3 . 9
R G 1 7 4
0 , 3 5
S C H I R M
S C H I R M
0 , 1 4
S W
1
2
X 1 3 3 3 8
R A D I O
A 4 2 1
D I V
E R S I T Y
R A D I O
S C H I R M
A N T - N F
A N T - N F
N 9
X 1 3 3 4 3
F
5 3 0 7 4 8
BOn-board monitor wiring harness-II-
8/20/2019 X5 Navigation Retrofit
37/37
13. Circuit diagram, on-board monitor wiring harness
Legend Colour abbreviations
A196 On-board monitor BR = Brown
A197 Video module RT = Red
A421 Diversity VI = Violet
A453 TV amplifier WS = White
N9 Radio GR = Grey
X229 R connector SW = Black
X581 Tacho A connector GN = Green
X1312 Navigation A GE = Yellow
X1313 Navigation B BL = Blue
X1362 58g connector
X1543 30 radio connector
X3279 31 connector
X6500 Adapter plug connector
X6501 Adapter cable connector
X6502 Adapter (+) plug connector
X10113 IKE 3
X10117 Light module C
X13016 Stereo/hi fi earth
X13318 Navigation system telephone
X13338 Aerial
X13342 Radio HF aerial
X13343 Radio ZF aerial
X13344 Diversity HF aerial
X13346 TV amplifier aerial, right
X13347 TV amplifier aerial, left
X13348 Video module aerial, right
X13349Video module aerial, left
X18126 Radio
X18344 I bus connector
X18801 On-board monitor control
X18802 On-board monitor
X18804 Video module II
X18805 Radio II
X18806 Video module III
X69990 Open cable