1
SERVICE MANUAL US ModelE Model
XM-1652Z
STEREO POWER AMPLIFIER
AUDIO POWER SPECIFICATIONS (US model)POWER OUTPUT AND TOTAL HARMONIC DISTORTION165 watts per channel minimum continuous average power into 4 ohms,both channels driven from 20 Hz to 20 kHz with no more than 0.04% totalharmonic distortion per Car Audio Ad Hoc Committee standards.
Other SpecificationsCircuit system OTL (output transformerless) circuit
Pulse power supplyInputs RCA pin jacks
High level input connectorInput level adjustment range
0.3 – 6 V (RCA pin jacks),1.2 – 12 V (High level input)
Outputs Speaker terminalsSpeaker impedance 2 – 8 Ω (stereo)
4 – 8 Ω (when used as a bridging amplifier)Maximum outputs 380 W × 2 (at 4 Ω)
1,000 W (BTL, at 4 Ω)Rated outputs (supply voltage at 14.4 V)
165 W RMS × 2 (20 Hz – 20 kHz, 0.04% THD+N, at 4 Ω)200 W RMS × 2 (20 Hz – 20 kHz, 0.1% THD+N, at 2 Ω)400 W RMS (BTL) (20 Hz – 20 kHz, 0.1% THD+N,at 4 Ω)
S/N Ratio 93 dBA (reference: 1 W into 4 Ω)Frequency response 5 Hz – 80 kHz ( dB)Harmonic distortion 0.008% or less (at 1 kHz, 4 Ω, 10 W)Low-pass filter 80 Hz, –18 dB/octPower requirements 12 V DC car battery
(negative ground)Power supply voltage 10.5 – 16 VCurrent drain at rated output : 40 A (4 Ω, 165 W × 2)
Remote input : 1 mADimensions Approx. 424 × 55 × 290 mm
(16 3/4 × 2 1/4 × 11 1/2 in.) (w/h/d) not incl.projecting parts and controls
Mass Approx. 4.0 kg (8 lb. 13 oz.) not incl. accessoriesSupplied accessories Mounting screws (4)
High level input cord (1)Protection cap (1)
Design and specifications are subject to change withoutnotice.
SPECIFICATIONS
+0–3
Ver. 1.0 2005. 01
9-879-394-012005A04-1
© 2005. 01
Sony Corporatione Vehicle Company
Published by Sony Engineering Corporation
2
TABLE OF CONTENTS
1. GENERALConnections ............................................................................. 3
2. DISASSEMBLY2-1. Bottom Plate ........................................................................ 52-2. Main Board Section ............................................................ 62-3. Main Board ......................................................................... 6
3. DIAGRAMS3-1. Printed Wiring Board .......................................................... 93-2. Schematic Diagram ........................................................... 10
4. EXPLODED VIEWS4-1. Heat Sink (Main) Section .................................................. 114-2. Main Board Section .......................................................... 12
5. ELECTRICAL PARTS LIST ........................................ 13
Notes on Chip Component Replacement• Never reuse a disconnected chip component.• Notice that the minus side of a tantalum capacitor may be dam-
aged by heat.
XM-1652Z
PROTECTOR OPERATION CHECK
Thermal Protect1. Short across TH901 with the power on.2. Verify that the protector is operated and LED901 illuminates
red.3. Verify that the protector is released and LED901 illuminates green
when the short is removed.4. Likewise, perform items 1 to 3 for TH902 and TH903.
Over Current Protect1. Short between the positive and negative sides of the speaker
output terminal CN903 (1/2) with the power on.(Perform this shorting for each channel on L and R.)
2. Verify that the protector is operated and LED901 illuminatesred.
3. Verify that the protector is not released and LED901 remainsred even when the short is removed.
4. Verify that the protector is released and LED901 illuminates greenwhen the power is turned off and then on again.
Offset Protect1. Short between the +12V terminal of CN903 (2/2) and the BTL+
or BTL– of the speaker output terminal CN903 (1/2).(Short between +12V terminal and BTL+ and between +12Vterminal and BTL–.)
2. Verify that the protector is operated and LED901 illuminatesred.
3. Verify that the protector is not released and LED901 remainsred even when the short is removed.
4. Verify that the protector is released and LED901 illuminates greenwhen the power is turned off and then on again.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINEWITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND INTHE PARTS LIST ARE CRITICAL TO SAFE OPERATION.REPLACE THESE COMPONENTS WITH SONY PARTS WHOSEPART NUMBERS APPEAR AS SHOWN IN THIS MANUAL ORIN SUPPLEMENTS PUBLISHED BY SONY.
3
XM-1652ZSECTION 1GENERAL This section is extracted
from instruction manual.
ConnectionsPrecautions• This unit is designed for negative ground 12 V DC operation only.• Use speakers with suitable impedance.
— 2 – 8 Ω (stereo), 4 – 8 Ω (when used as a bridging amplifier).• Do not connect any active speakers (with built-in amplifiers) to the speaker terminals of the unit. Doing
so may damage the amplifier and active speakers.• Avoid installing the unit in areas subject to:
— high temperatures such as from direct sunlight or hot air from the heater— rain or moisture— dust or dirt.
• If your car is parked in direct sunlight and there is a considerable rise in temperature inside the car,allow the unit to cool down before use.
• When installing the unit horizontally, be sure not to cover the fins with the floor carpet etc.• If this unit is placed too close to the car radio unit or antenna, interference may occur. In this case,
relocate the amplifier away from the car radio unit or antenna.• If no power is being supplied to the car radio unit, check the connections.• This power amplifier employs a protection circuit to protect the transistors and speakers if the amplifier
malfunctions. Do not attempt to test the protection circuits by covering the heat sink or connectingimproper loads.
• Do not use the unit on a weak battery as its optimum performance depends on a good power supply.• For safety reasons, keep your car audio unit volume moderate so that you can still hear sounds outside
your car.• By default, the FILTER selector switch is in “LPF” position. When connecting the full range speaker, set
to the “OFF” position.
Caution• Before making any connections, disconnect the ground terminal of the car battery to avoid short circuits.• Be sure to use speakers with an adequate power rating. If you use small capacity speakers, they may be
damaged.• Do not connect the # terminal of the speaker system to the car chassis, and do not connect the #
terminal of the right speaker with that of the left speaker.• Install the input and output cords away from the power supply wire as running them close together can
generate some interference noise.• This unit is a high powered amplifier. Therefore, it may not perform to its full potential if used with the
speaker cords supplied with the car.• If your car is equipped with a computer system for navigation or some other purpose, do not remove the
ground wire from the car battery. If you disconnect the wire, the computer memory may be erased. Toavoid short circuits when making connections, disconnect the +12 V power supply wire until all theother wires have been connected.
ConexionesPrecauciones• Esta unidad está diseñada para utilizarse sólo con cc de 12 V negativo a masa.• Utilice altavoces con una impedancia adecuada.— de 2 a 8 Ω (estéreo) , de 4 a 8 Ω (cuando se utilizan como amplificadores en puente).
• No conecte altavoces activos (con amplificadores incorporados) a los terminales de altavoz de la unidad.Si lo hace, puede dañar el amplificador y los altavoces activos.
• Evite instalar la unidad en lugares expuestos a:— altas temperaturas, como a la luz solar directa o al aire caliente de la calefacción— la lluvia o la humedad— suciedad o polvo.
• Si aparca el automóvil bajo la luz solar directa y se produce un considerable aumento de temperatura enel interior, deje que la unidad se enfríe antes de utilizarla.
• Si instala la unidad horizontalmente, asegúrese de no cubrir las aletas con la moqueta del suelo, etc.• Si conecta la unidad demasiado cerca de la radio o antena del automóvil, pueden producirse
interferencias. En este caso, aleje el amplificador de dicha radio o antena.• Si la radio del automóvil no recibe alimentación, compruebe las conexiones.• Este amplificador de potencia emplea un circuito de protección para proteger los transistores y los
altavoces en caso de que dicho amplificador presente fallas de funcionamiento. No intente someter aprueba los circuitos de protección cubriendo el disipador de calor o conectando cargas inadecuadas.
• No utilice la unidad si la batería se está agotando, ya que el rendimiento óptimo de dicha unidaddepende de un buen suministro de alimentación.
• Por razones de seguridad, mantenga el volumen del sistema de audio para automóvil moderado deforma que sea posible oír los sonidos del exterior del automóvil.
• Por defecto, el interruptor de selección FILTER se encuentra en la posición “LPF”. Al conectar el altavozde rango completo, ajuste el interruptor en la posición “OFF”.
Precaución• Antes de realizar las conexiones, desconecte el terminal de toma a tierra de la batería del automóvil para
evitar cortocircuitos.• Asegúrese de utilizar altavoces con una potencia nominal adecuada. Si emplea altavoces de pequeña
capacidad, pueden dañarse.• No conecte el terminal # del sistema de altavoces al chasis del automóvil, ni el terminal # del altavoz
derecho al del altavoz izquierdo.• Instale los cables de entrada y salida alejados del cable de suministro de alimentación, ya que en caso
contrario puede generarse ruido por interferencias.• Esta unidad es un amplificador de alta potencia. Por tanto, puede no funcionar a pleno rendimiento si se
utiliza con los cables de altavoz suministrados con el automóvil.• Si el automóvil está equipado con un sistema de computadora para la navegación o para otra finalidad,
no desconecte el conductor de toma a tierra de la batería del automóvil. Si lo desconecta, la memoria dela computadora puede borrarse. Para evitar cortocircuitos al realizar las conexiones, desconecte el cablede suministro de alimentación de +12 V hasta conectar todos los cables.
Power Connection Wires (not supplied)Cables de conexión de alimentación (no suministrados)
Fuse (60 A)Fusible (60 A)
+12 V car batteryBatería de automóvil de +12 V
Car audio unit
Sistema de audio paraautomóvil
to a metal point of the cara un punto metálico delautomóvil
REM +12V GNDREM +12V GND3
3
Notes on the power supply• Connect the +12 V power supply wire only after all the other wires have been connected.• Be sure to connect the ground wire of the unit securely to a metal point of the car. A loose connection may
cause a malfunction of the amplifier.• Be sure to connect the remote control wire of the car audio unit to the remote terminal.• When using a car audio unit without a remote output on the amplifier, connect the remote input terminal
(REMOTE) to the accessory power supply.• Use the power supply wire with a fuse attached (60 A).• All power wires connected to the positive battery post should be fused within 450 mm (18 in) of the battery post,
and before they pass through any metal.• Make sure that the vehicle’s battery wires connected to the vehicle (ground to chassis) *2 are of a wire gauge at
least equal to that of the main power wire connected from the battery to the amplifier.• Make sure that the wires to be connected to the +12 V and GND terminals of this unit at least 8-Gauge (AWG-8)
or have a sectional area of more than 8 mm 2(11/32 in2).
Notas sobre el suministro de alimentación• Conecte el cable de suministro de alimentación de +12 V sólo después de haber conectado los otros cables.• Asegúrese de conectar firmemente el cable de toma a tierra de la unidad a un punto metálico del automóvil.
Una conexión floja puede causar fallas de funcionamiento del amplificador.• Compruebe que conecta el cable de control remoto del sistema de audio para automóvil al terminal remoto.• Si utiliza un sistema de audio para automóvil sin salida remota en el amplificador, conecte el terminal de entrada
remota (REMOTE) al suministro de alimentación accesoria.• Emplee el cable de suministro de alimentación con un fusible fijado (60 A).• Todos los cables de alimentación conectados al polo positivo de la batería deben conectarse a un fusible situado a
menos de 450 mm del polo de la batería, y antes de pasar por ninguna pieza metálica.• Asegúrese de que los cables de la batería del vehículo conectados al mismo (a la masa del chasis) *2 tiene una
anchura igual o superior a la del cable de alimentación principal que conecta la batería con el amplificador.• Compruebe que los cables que se van a conectar a los terminales +12 V y GND de esta unidad tengan una
capacidad de al menos 8-Gauge (AWG 8) o una zona de sección de más de 8 mm 2.
Remote output *1
Salida remota *1
(REM)
*1 If you have the factory original or some other caraudio unit without a remote output for the amplifier,connect the remote input terminal (REMOTE) to theaccessory power supply.
Make the terminal connections as illustrated below.Realice las conexiones de terminal como se ilustra a continuación.
Pase los cables a través de la cubierta,conéctelos y cubra los terminales con dichacubierta.
NotaAl apretar el tornillo, tenga cuidado de no aplicardemasiada fuerza de torsión *, ya que puededañarlo.* El valor de fuerza de torsión debe ser inferior a
1 N•m.
Pass the wires through the cap, connect thewires, then cover the terminals with the cap.
NoteWhen you tighten the screw, be careful not toapply too much torque * as doing so may damagethe screw.* The torque value should be less than 1 N•m.
c
*1 Si dispone del sistema de audio para automóviloriginal de fábrica o de otro sistema sin una salidaremota en el amplificador, conecte el terminal deentrada remota (REMOTE) al suministro dealimentación accesoria.
Notes• When using passive crossover networks in a multi-
speaker system, care must be taken as the speakersystem’s impedance should not be lower than that of thesuitable impedance for this unit.
• When you are installing a 12 decibels/octave system inyour car, the following points must be considered. In a12 decibels/octave system where both a choke andcapacitor are used in series to form a circuit, great caremust be taken when they are connected. In such acircuit, there is going to be an increase in the currentwhich bypasses the speaker with frequencies around thecrossover frequency. If audio signals continue to be fedinto the crossover frequency area, it may cause theamplifier to become abnormally hot or the fuse to blow.Also if the speaker is disconnected, a series-resonantcircuit will be formed by the choke and the capacitor. Inthis case, the impedance in the resonance area willdecrease dramatically resulting in a short circuit situationcausing damage to the amplifier. Therefore, make surethat a speaker is connected to such a circuit at all times.
Notas• A l utilizar redes de cruce pasivas en un sistema con
múltiples altavoces, es necesario asegurar que laimpedancia del sistema de altavoces no sea inferior alvalor de impedancia adecuado para esta unidad.
• A l instalar un sistema de 12 decibelios/octava en unautomóvil, hay que tener en cuenta los siguientes puntos.En un sistema de 12 decibelios/octava donde se empleauna bobina de choque y un condensador en serie paraformar un circuito, hay que tener mucho cuidado alconectarlos. En los circuitos de este tipo, se produce unaumento de la corriente que pasa por alto el altavoz, confrecuencias próximas a la frecuencia de cruce. Si lasseñales de audio siguen enviándose a la zona defrecuencia de cruce, puede producirse unsobrecalentamiento anormal del amplificador o puedefundirse el fusible. Además, si se desconecta el altavoz, seformará un circuito de resonancia en serie compuesto porla bobina y el condensador. En este caso, la impedanciadel área de resonancia disminuirá considerablemente,dando lugar a una situación de cortocircuito y dañando elaltavoz. Por tanto, es necesario asegurar que el altavozesté conectado a un circuito en todo momento.
CrossoverFrequency unit:
Hz
50
80
100
130
150
200
260
400
600
800
1000
L(coil)* unit:
mH
12.7
8.2
6.2
4.7
4.2
3.3
2.4
1.6
1.0
0.8
0.6
C1/C2(capacitor)* unit:
µF
800
500
400
300
270
200
150
100
68
50
39
Table of crossover values for 6 dB/octave (4 ohms) (Speaker Connections 4)
Frecuencia decruce
unidad: Hz
50
80
100
130
150
200
260
400
600
800
1000
L(bobina) *
unidad: mH
12,7
8,2
6,2
4,7
4,2
3,3
2,4
1,6
1,0
0,8
0,6
C1/C2(condensador)*
unidad: µF
800
500
400
300
270
200
150
100
68
50
39
Tabla de valores de cruce para 6 dB/octava (4 Ω) (Conexiones de los altavoces 4)
* No suministrado
less than 450 mm (18 in)menos de 450 mm
* Not supplied
*2
4
XM-1652Z
(80Hz)
OFF ON
LPF(80Hz)
OFF ON
LPF
BTLBTL
BTLBTL
(80Hz)
OFF ON
LPF
Input Connections
Speaker ConnectionsTurn on or off the LPF switch at the unit rear as illustrated below.
Conexiones de entrada
Conexiones de los altavocesEncienda o apague el interruptor LPF situado en la parte posterior de la unidad, como se muestra a continuación.
High Level Input Connection (with Speaker Connection 1 or 4)Conexión de entrada de alto nivel (con conexión de altavoces 1 ó 4)AAAAA
High Level Input Connection (with Speaker Connection 3)Conexión de entrada de alto nivel (con conexión de altavoces 3)BBBBB
High Level Input Connection (with Speaker Connection 2)Conexión de entrada de alto nivel (con conexión de altavoces 2)
Line Input Connection (with Speaker Connection 1, 2 or 4)Conexión de entrada de línea (con conexión de altavoces 1, 2 ó 4)
Line Input Connection (with Speaker Connection 3)Conexión de entrada de línea (con conexión de altavoces 3)
CCCCC
DDDDD
EEEEE
(80Hz)
OFF ON
LPF
Right speakerAltavoz derecho
Left speakerAltavoz izquierdo
WhiteBlanco
GrayGris
2
StripedCon rayas
StripedCon rayas
2-Speaker System (with Input Connection A or D)Sistema de 2 altavoces (con conexión de entrada A o D)11111
NoteMake sure that the line output from the car audio unit isconnected to the jack marked “L (BTL)” on the unit.
NoteIf you wish to use a subwoofer as the monaural speaker,connect the speaker as illustrated above. The outputsignals to the subwoofer will be the combination ofboth right and left output signals.
Left speaker outputSalida del altavoz izquierdo
Right speaker outputSalida del altavoz derecho
StripedCon rayas
StripedCon rayas
Car audio unitSistema de audio para
automóvil
WhiteBlanco
GrayGris
WhiteBlanco
White/BlackstripedCon rayasblancas y negras
Gray/BlackstripedCon rayasgrises y negras
GrayGris
2
RL
Left speaker outputSalida del altavozizquierdo
Right speaker outputSalida del altavozderecho
StripedCon rayas
StripedCon rayas
StripedCon rayas
StripedCon rayas
Car audio unitSistema de audio para
automóvil
2 2
LINE OUT
Right channelCanal derecho
Left channelCanal izquierdo
LINE OUT
Left speaker (min. 2 Ω )Altavoz izquierdo (mín. 2 Ω )
Right speaker (min. 2 Ω )Altavoz derecho (mín. 2 Ω)
Subwoofer (with Input Connection C or D)Altavoz potenciador de graves (con conexión de entrada C o D)22222
1-Speaker System (with Input Connection B or E)Sistema de 1 altavoz (con conexión de entrada B o E)33333
C1 C2
L
SubwooferAltavoz potenciador de graves
Left speakerAltavoz izquierdo
Right speakerAltavoz derecho
Dual Mode System (with a Bridged Subwoofer A or D)Sistema de modo dual (con altavoz potenciador de graves en puente A o D)44444
BTLBTL
(80Hz)
OFF ON
LPF
Subwoofer (min. 4 Ω )Altavoz potenciador de graves(mín. 4 Ω )
Right speaker(min. 4 Ω)Altavoz derecho(mín. 4 Ω)
Left speaker(min. 4 Ω )Altavoz izquierdo(mín. 4 Ω)
L (BTL) L (BTL)
NotaSi desea utilizar el altavoz potenciador de graves comoaltavoz monoaural, conecte el altavoz tal como semuestra en la ilustración anterior. Las señales que seemiten hacia el altavoz potenciador de graves serán unacombinación de las señales de salida derecha e izquierda.
NotaAsegúrese de que la salida de línea del sistema de audiopara automóvil está conectada a la toma con la marca“L (BTL)” de la unidad.
Car audio unitSistema de audio para
automóvil
Car audio unitSistema de audio para
automóvil
Car audio unitSistema de audio para
automóvil
Level Adjustment ControlThe input level can be adjusted with this controlwhen using source equipment made by othermanufacturers. Turn it in the clockwise directionwhen the output level of the car audio unitseems low.
Control de ajuste de nivelEs posible ajustar el nivel de entrada con estecontrol al utilizar equipos fuente de otrosfabricantes. Gírelo en el sentido de las agujas delreloj si el nivel de salida del sistema de audiopara automóvil parece bajo.
0.3V6
42 1
0.5
LEVEL0.3V6
42 1
0.5
LEVEL
5
XM-1652ZSECTION 2
DISASSEMBLY
Note : This set can be disassemble according to the following sequence.
Note : Follow the disassembly procedure in the numerical order given.
2-1. BOTTOM PLATE
2-1. BOTTOM PLATE(Page 5)
2-2. MAIN BOARD SECTION (Page 6)
SET
2-3. MAIN BOARD(Page 6)
3 bottom plate
1 four screws (+BTP 3 x 5)
2 four screws (+BTP 3 x 5)
6
XM-1652Z
2-2. MAIN BOARD SECTION
2-3. MAIN BOARD
1 three screws (+BTP 3 x 8)
2 three screws (+BTP 3 x 8)
4 screw (+BTP 3 x 8)
3 three screws (+BTP 3 x 8)
After unfastening the screw,taping with the screw insertedfacilitates the work.
5 MAIN board section
heat sink (MAIN)
4 panel (front)
5 MAIN board
3 two screws (+BTP 3 x 8)
1 screw (+BTP 3 x 8)
2 screw (+BTP 3 x 8)
8
XM-1652ZSECTION 3DIAGRAMS
IC902 µPC494GS
16 15 14 13 12 11 10 9
1 2 3 4 5 6 7 8
OSC
REF. REG.
ERROR
ERROR
0.1V
• IC Block Diagram
THIS NOTE IS COMMON FOR PRINTED WIRINGBOARDS AND SCHEMATIC DIAGRAMS.(In addition to this, the necessary note isprinted in each block.)
for schematic diagram:• All capacitors are in µF unless otherwise noted. (p: pF)
50 WV or less are not indicated except for electrolyticsand tantalums.
• All resistors are in Ω and 1/4 W or less unless otherwise
specified.
• A : B+ Line.• B : B– Line.• Power voltage is dc 14.4V and fed with regulated dc power
supply from +12V and REM terminals.• Voltage is dc with respect to ground under no-signal
condition.• Voltages are taken with a VOM (Input impedance 10 MΩ).
Voltage variations may be noted due to normal produc-tion tolerances.
• Waveforms are taken with a oscilloscope.Voltage variations may be noted due to normal produc-tion tolerances.
• Circled numbers refer to waveforms.• Signal path.
F : AUDIO
for printed wiring boards:• : Pattern from the side which enables seeing.
3.6 Vp-p
22.5 µsec
1 IC902 5 (CT)
1 V/DIV, 5 µsec/DIV
• Waveform
Note: The components identified by mark 0 or dotted linewith mark 0 are critical for safety.Replace only with part number specified.
9 9
XM-1652Z
XM-1652Z
3-1. PRINTED WIRING BOARD
• Semiconductor Location
D301 D-4D302 C-13D303 C-13D304 B-10D305 B-10D306 E-8D307 F-8D308 F-8D309 F-8D901 I-6D902 G-8D903 F-8
IC301 H-4IC302 H-3IC303 H-3IC304 G-5IC901 H-6IC902 F-9IC903 F-8
LED901 J-7
Q101 G-4Q102 F-4Q103 E-4Q104 E-4Q105 E-4Q106 E-4Q107 E-4Q108 E-4Q109 E-2Q110 E-2Q111 B-2Q112 B-2Q113 C-2Q114 D-2Q115 D-2Q116 D-2Q117 F-2Q118 F-2Q119 F-2Q120 G-2
Ref. No. LocationQ121 H-2Q201 G-4Q202 F-4Q203 E-5Q204 E-5Q205 E-5Q206 E-4Q207 E-5Q208 E-5Q209 B-7Q210 B-7Q211 B-5Q212 B-4Q213 B-9Q214 B-9Q215 B-8Q216 B-8Q217 B-7Q218 B-6Q219 B-6Q220 B-5Q221 B-5Q301 H-5Q307 B-10Q308 B-10Q309 E-8Q310 E-8Q311 F-8Q901 G-8Q902 G-8Q903 G-9Q904 E-9Q905 E-10Q906 J-7Q907 E-12Q908 E-12Q909 G-13Q910 E-13Q911 F-13Q912 D-13Q913 F-13Q914 D-13
Ref. No. Location
1
A
B
C
D
E
F
G
H
I
J
2 3 4 5 6 7 8 9 10 11 12 13 14
JW35
JW36JW29
L901 L902
JW37
JW33JW32
JW30
1-865-342- 11JW31 C901
JW34
JW40
JW41
JW42
JW43
JW44
JW45
JW46
JW47
JW48
JW51
TH30
1
TH30
3
TH30
2
R922
R925
R927 R9
24
JW10
1
Q914
Q912
Q910
JW18
8
JW18
7L3
01
JW183
T901
JW182
R238R241R244
JW181
JW180JW179
JW184JW185
JW186
Q214Q216
Q209
Q213
JW18
9JW
190
JW19
1JW
192
JW19
3
JW99
J8
JW50
JW53
JW52
JW49
JW12JW56JW57
R928
R930
R932
R929
R931
R933
C320C321
C317
D302
AK
AK
AK
D303
C315
C316
C914
C907
R914
J7
R920
R921
JW10
5
JW63
JW62
JW64
JW10
4
C910
R913 R9
12R9
11
R910
R905
JW66
JW65
JW67
JW85
JW86
C311
JW17
0JW
169
JW16
8
JW16
7JW16
0
JW12
5
JW12
4
JW12
3JW
122
JW12
1JW
120
JW11
9
JW11
8JW
117
JW11
6
JW11
5
JW11
4JW
113
JW11
2
JW11
1JW
110
JW10
9
JW10
8JW
107
JW10
6
JW19
4
JW61
JW60
JW59
JW16
1JW
162 JW
166
C312
C314
C313
C319
C318 D3
04
D305
R248
R237R2
39R2
49
Q215
R232
R233
R231
R250R2
51
Q218
R243 R2
42
R252
R253
R311
A
AK
B
E
B
E
B
EB
E
B EC
B
E
E
B
C
C
CC
C
B
ECC
E
B C
D301
Q905
Q106Q206Q105 Q205
E
BC
A
AK
Q906
D901
Q210
Q907
Q908
R312
R145
R148
R130
R150
R151
R142
R152
R117
R115
R118 R218
R229 R228
R215
Q301
Q201
Q101 R310
R217R317
R213
J1
J6
-2 -4
-1 -3J5
R301
R102
R101
R201
R918
R919
R146
R202
R208R209
C301
R108
JW22
JW25
JW28
R G
JW21
JW14JW15
JW16
JW23JW24
JW83
JW84
JW82
JW87
Q102 Q202
JW20JW19
JW18JW17
C207
JW4JW3
VR301
JW9
JW8JW7
OFF ON
-2-1
SW301
SW301LPF(80Hz)
VR301LEVEL
POWER/PROTECTOR
CN902INPUT
CN901
CN901
HIGH LEVEL INPUT
SPEAKER OUT
CN903
30AF902
30A REM +12V GNDF901
JW2
JW1
R112
R211
R111
R210
R110
R109
R203
R204
R207
R206
R205
R105
R935
R936
C104
C105
C304
C309
C101
C201
JW26
C307
C303
C903
C114 C115R246
R903R904
R906
R319
C322
R147R247
R318
R917R916
Q904
R915
R934
R909
C906JW68
Q901
JW69
Q902
Q903CC B E
CB E
C
C
B E
E B
CB E
C
C
C C
E
B
E
B
E
B
E
BKA
A
E B
IC901
R902
C214
C323
C911
C909
C912
C215
C905
C204
C324
C326
C216
C325
C212
C205
C306
C107
C208
C203
C305
C103
C102 C202
LED901
R106
R306
R302 R1
03R1
04R1
07
R212
C106
C302
J2
R305
R304
R303
R214
IC3031 4
8 5
4
8 51 4
8 5
1
4
8 5
1
IC302
IC301
IC304
C308JW10
JW11
JW6JW5
C206
C310
C209C109
C210
C110
JW13R153
C116
C111
C112
Q103 Q104 Q203 Q204
R128R129
R122 R124 R222
R230
R224
R137
R139
R132Q109
R133
R131
R149
R121
R140
Q110
R119
R116
R154
R254
JW89
JW27
JW91
JW90
JW88
R143
R123
R120
JW92
JW93 JW
94JW
95
R125
R220
R225
R126
R134
R226
R234
R127
R221
R223
R227
R322
D309
D307
D308
R907
JW81
JW80
JW79
JW78
JW77
JW76
JW75
JW74
JW73
JW72
JW71
JW70
R908 D902
R307R3
08R3
09R3
15
R313
R314 R3
16
R216
R219
R136
C113
R135
JW196
JW198JW197
R235JW149
JW14
4 JW14
5
JW15
0
JW13
2
R138
JW13
3
JW13
4JW
135
JW15
1
R245
JW143
JW148
JW147
JW146
JW142
JW141JW140JW139
JW138JW137JW136
C213
JW17
7JW
178
JW17
1JW
172
JW17
3
JW17
4JW
175
JW17
6
JW16
5JW
164
JW16
3JW15
9JW
158
R240
JW157
JW155JW154
JW156
R236
R321 R320
R923
R926JW55
JW103
JW100
JW195
JW102
JW98
JW58
JW39
JW38
JW54
R901 C9
02
C915
C918C917C916
BE C C C C CBE BE
Q217
B
B C E
E
Q219
BE C CQ220Q211
BE C
Q113
BE
Q114
BC
CE
BE
C
Q116
Q117 R1
41R1
44
BC
EB
CE
Q119
Q120
BC
E
ECB
Q212
ECB
Q108
EB
EB
Q115EC
Q118C
Q121C
B
Q107 C211
JW96
JW152JW131
JW130JW129
JW127
JW128JW126
JW153
JW97
Q309 Q310C913
D903C908
IC903
IC902
Q311
D306
Q208 Q207
Q111
EC
BE
CBQ1
12
E C
B
E
BC
E C
B
E C B E C BB C E B C E
Q221
E C
B
Q308 Q307
EB EB
SD
GS
DD
DD
DG
SG
SG
SG
SG
Q913
Q911
Q909
-1L
(BTL)
-2R
-1L
-3R
-2 -4
L
BTL
R
1
1
4 3
2
1
4 3
2
8
16 9
C1B1 B2E
C2 C1B1 B2E
C2 C1B1 B2E
C2 C1B1 B2E
C2
BC
E
B EC
MAIN BOARD
10 10
XM-1652Z
XM-1652Z
3-2. SCHEMATIC DIAGRAM • Refer to page 8 for IC Block Diagram and Waveform.
IC B/D
C901
T901
F901
CN902
C102
CN901
C101
C302 R302R301
C301
R103
R203
IC301(1/2)
IC301(2/2)
R926
Q101
Q201
Q903
C202
C201
R10
2
R10
1R
201
R20
2
R107
R106
R206
R207
C104
C204
R104
R204
C105
C103 C303
C304
C205
C203
R109
R209
C305 C307
R303
R304
R305
C308
SW301(1/2)
SW301(2/2)
R110 R111
R210 R211
IC303(1/2)C206
C106
C107
C207
C208
R214
R213
IC303(2/2)
R117
R217
R309
C324
C325
R310
R313 C326
R314
R315
C310
R116C109
R115
R119
R118
C116
Q103
Q104
C111
R127
Q107
R128
C112
R129
Q108
R130
R132
Q110
C113
R135
Q111
R136Q113
R138R148
Q114
R137
Q112
R149
R139
R140
R142
R143
Q117 Q120
R150 R152
R151 R153R141 R144
R145
Q119Q116
R134
C209
R215
R216
R218
Q203
C216
C210
R227
C211
R228
C212
R229
R230
R232
Q210
C213
Q211
Q212
R236Q213
R248R238
R249
R237Q214
R240
R239Q219Q216
Q220Q217
R250 R252
R251 R253R244R241
R243
R245
Q901
R907R905
D902
R908
R904C905
R903R902
C902R901
F902
C906
IC902
R909
R913
C911
R912
C910
C907
C908
R934
C909
R91
0
R914
R918
R919
C914R915
C913
C912
R916R917
R920
R921
R923
R922
R924
R925
R927
Q907
Q908
R928 R930 R932
R929 R931 R933
Q909 Q911 Q913
Q910 Q912 Q914
C915
C916
C917
C918
C313C311
C312 C314
C315
C316
R320
C318 D304
C319
R321
D305
Q307
C317
C320
C321
R318
R319
D307
D308
D309
R322
Q309
Q310
C322 C323
C114
C115
R146
C214
C215
R246
R247 R147
R936
C903
R935
R306 C309
R317
D901
R108
R105
R205
R208
IC302(1/2)
VR301
VR301
R112
R212
R154
R254
Q102
R121 R122
R125
R131
R120 R123 R124
R133
Q109
R242
R235
Q209
R233
R231
R224R223R220
Q204
R225
R221
R219
R234
IC304(1/2)
R316R312R311
IC304(2/2)
R308R307
TH303TH302TH301
D306
Q311
IC903
LED901
Q906Q905
Q904
Q902
R906L902
L901
Q106
Q205
Q206
R226
Q121
Q118
Q221
Q218Q215
Q301
Q207
Q208
CN903D903
IC901
L301
D302
Q308
R222
Q202
IC302(2/2)
C306
D301
Q105
Q115
CN903
C110
D303
R126
R911
11
XM-1652ZSECTION 4
EXPLODED VIEWS
NOTE:• The mechanical parts with no reference
number in the exploded views are not supplied.• Items marked “*” are not stocked since
they are seldom required for routine service.Some delay should be anticipatedwhen ordering these items.
• Color Indication of Appearance PartsExample :
KNOB, BALANCE (WHITE) ... (RED)
Parts Color Cabinet’s Color• Accessories are given in the last of this parts list.
The components identified bymark 0 or dotted line with mark0 are critical for safety.Replace only with part numberspecified.
Ref. No. Part No. Description Remark
4-1. HEAT SINK (MAIN) SECTION
R
Ref. No. Part No. Description Remark
R
* 1 2-546-701-01 PLATE, BOTTOM0F901 1-532-947-11 FUSE (BLADE TYPE) (AUTO FUSE) (30A)0F902 1-532-947-11 FUSE (BLADE TYPE) (AUTO FUSE) (30A)
#1 7-685-544-14 SCREW +BTP 3X5 TYPE2 N-S#2 7-685-546-14 SCREW +BTP 3X8 TYPE2 N-S
#1
not supplied
#1
#2
#2
#2
#2
F901
F902
1
12
XM-1652Z
4-2. MAIN BOARD SECTION
Ref. No. Part No. Description RemarkRef. No. Part No. Description Remark
#2
#2
not suppliednot supplied
not supplied
#5
#3
#3
#3#3
#3
#3
#3
#3
#4
#4
#4
52
53
54
51
51 A-1088-884-A MAIN BOARD, COMPLETE52 2-546-700-01 PANEL (FRONT) (US)52 2-546-700-11 PANEL (FRONT) (E)53 3-912-431-01 SCREW (+–P)
54 3-253-537-01 SCREW (M5X11)#3 7-682-948-01 SCREW +PSW 3X8#4 7-682-648-09 SCREW +PS 3X8#5 7-685-546-19 SCREW +BTP 3X8 TYPE2 N-S
13
XM-1652ZSECTION 5
ELECTRICAL PARTS LIST
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
NOTE:• Due to standardization, replacements in
the parts list may be different from theparts specified in the diagrams or thecomponents used on the set.
• RESISTORSAll resistors are in ohms.METAL:Metal-film resistor.METAL OXIDE: Metal oxide-film resistor.F:nonflammable
• Items marked “*” are not stocked sincethey are seldom required for routine service.Some delay should be anticipatedwhen ordering these items.
• SEMICONDUCTORSIn each case, u : µ, for example:uA.. : µA.. uPA.. : µPA..uPB.. : µPB.. uPC.. : µPC.. uPD.. : µPD..
• CAPACITORSuF : µF
• COILSuH : µH
A-1088-884-A MAIN BOARD, COMPLETE*********************
3-253-537-01 SCREW (M5X11)3-912-431-01 SCREW (+–P)7-682-648-09 SCREW +PS 3X87-682-948-01 SCREW +PSW 3X87-685-146-14 SCREW +P 3X8 TYPE2 NON-SLIT
< CAPACITOR >
C101 1-162-927-11 CERAMIC CHIP 100PF 5% 50VC102 1-162-927-11 CERAMIC CHIP 100PF 5% 50VC103 1-162-923-11 CERAMIC CHIP 47PF 5% 50VC104 1-162-923-11 CERAMIC CHIP 47PF 5% 50VC105 1-162-923-11 CERAMIC CHIP 47PF 5% 50V
C106 1-126-933-11 ELECT 100uF 20% 16VC107 1-162-923-11 CERAMIC CHIP 47PF 5% 50VC109 1-126-933-11 ELECT 100uF 20% 16VC110 1-126-933-11 ELECT 100uF 20% 16VC111 1-162-923-11 CERAMIC CHIP 47PF 5% 50V
C112 1-162-919-11 CERAMIC CHIP 22PF 5% 50VC113 1-100-597-11 CERAMIC CHIP 0.1uF 10% 25VC114 1-100-597-11 CERAMIC CHIP 0.1uF 10% 25VC115 1-100-597-11 CERAMIC CHIP 0.1uF 10% 25VC116 1-162-923-11 CERAMIC CHIP 47PF 5% 50V
C201 1-162-927-11 CERAMIC CHIP 100PF 5% 50VC202 1-162-927-11 CERAMIC CHIP 100PF 5% 50VC203 1-162-923-11 CERAMIC CHIP 47PF 5% 50VC204 1-162-923-11 CERAMIC CHIP 47PF 5% 50VC205 1-162-923-11 CERAMIC CHIP 47PF 5% 50V
C206 1-126-933-11 ELECT 100uF 20% 16VC207 1-162-923-11 CERAMIC CHIP 47PF 5% 50VC208 1-162-923-11 CERAMIC CHIP 47PF 5% 50VC209 1-126-933-11 ELECT 100uF 20% 16VC210 1-126-933-11 ELECT 100uF 20% 16V
C211 1-162-923-11 CERAMIC CHIP 47PF 5% 50VC212 1-162-919-11 CERAMIC CHIP 22PF 5% 50VC213 1-100-597-11 CERAMIC CHIP 0.1uF 10% 25VC214 1-100-597-11 CERAMIC CHIP 0.1uF 10% 25VC215 1-100-597-11 CERAMIC CHIP 0.1uF 10% 25V
C216 1-162-923-11 CERAMIC CHIP 47PF 5% 50VC301 1-165-128-11 CERAMIC CHIP 0.22uF 16VC302 1-126-934-11 ELECT 220uF 20% 16VC303 1-100-597-11 CERAMIC CHIP 0.1uF 10% 25VC304 1-100-597-11 CERAMIC CHIP 0.1uF 10% 25V
C305 1-100-597-11 CERAMIC CHIP 0.1uF 10% 25VC306 1-100-756-11 CERAMIC CHIP 0.047uF 50VC307 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC308 1-126-933-11 ELECT 100uF 20% 16VC309 1-100-597-11 CERAMIC CHIP 0.1uF 10% 25V
C310 1-126-965-11 ELECT 22uF 20% 50VC311 1-107-914-11 ELECT 1000uF 20% 50VC312 1-107-914-11 ELECT 1000uF 20% 50VC313 1-107-914-11 ELECT 1000uF 20% 50VC314 1-107-914-11 ELECT 1000uF 20% 50V
C315 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC316 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC317 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50VC318 1-100-597-11 CERAMIC CHIP 0.1uF 10% 25VC319 1-100-597-11 CERAMIC CHIP 0.1uF 10% 25V
C320 1-100-597-11 CERAMIC CHIP 0.1uF 10% 25VC321 1-100-597-11 CERAMIC CHIP 0.1uF 10% 25VC322 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50VC323 1-104-655-11 ELECT 470uF 20% 6.3VC324 1-100-597-11 CERAMIC CHIP 0.1uF 10% 25V
C325 1-162-923-11 CERAMIC CHIP 47PF 5% 50VC326 1-100-597-11 CERAMIC CHIP 0.1uF 10% 25VC901 1-137-194-11 FILM 0.47uF 5% 50VC902 1-100-597-11 CERAMIC CHIP 0.1uF 10% 25VC903 1-100-597-11 CERAMIC CHIP 0.1uF 10% 25V
C905 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50VC906 1-126-933-11 ELECT 100uF 20% 16VC907 1-100-597-11 CERAMIC CHIP 0.1uF 10% 25VC908 1-126-933-11 ELECT 100uF 20% 16VC909 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C910 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC911 1-100-597-11 CERAMIC CHIP 0.1uF 10% 25VC912 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50VC913 1-126-960-11 ELECT 1uF 20% 50VC914 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C915 1-100-597-11 CERAMIC CHIP 0.1uF 10% 25VC916 1-128-951-31 ELECT 2200uF 20% 16VC917 1-128-951-31 ELECT 2200uF 20% 16VC918 1-128-951-31 ELECT 2200uF 20% 16V
< CONNECTOR >
* CN901 1-691-785-11 PIN, CONNECTOR (PC BOARD) 4P(HIGH LEVEL INPUT)
The components identified bymark 0 or dotted line with mark0 are critical for safety.Replace only with part numberspecified.
When indicating parts by referencenumber, please include the board.
MAIN
14
XM-1652Z
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
< JACK >
CN902 1-770-068-82 JACK, PIN 2P (INPUT)
< TERMINAL BOARD >
CN903 1-780-220-11 TERMINAL BOARD (4P+3P+2FUSE)(SPEAKER OUT,REM,+12V,GND,30A,30A)
< DIODE >
D301 8-719-914-43 DIODE DAN202KD302 8-719-079-00 DIODE FCH10A15D303 8-719-079-01 DIODE FRH10A15D304 8-719-083-83 DIODE UDZS-TE17-15BD305 8-719-083-52 DIODE UDZSTE-1716B
D306 8-719-914-43 DIODE DAN202KD307 8-719-083-87 DIODE UDZSTE-1733BD308 8-719-083-87 DIODE UDZSTE-1733BD309 8-719-083-71 DIODE UDZSTE-1730BD901 8-719-914-43 DIODE DAN202K
D902 8-719-083-52 DIODE UDZSTE-1716BD903 8-719-914-43 DIODE DAN202K
< IC >
IC301 8-759-710-28 IC NJM4565M-AIC302 8-759-710-28 IC NJM4565M-AIC303 8-759-710-28 IC NJM4565M-AIC304 8-759-710-28 IC NJM4565M-AIC902 8-759-144-88 IC uPC494GS
< PHOTO COUPLER >
IC901 8-719-156-73 PHOTO COUPLER PS2501-1-LIC903 8-719-156-73 PHOTO COUPLER PS2501-1-L
< JUMPER RESISTOR >
J1 1-216-295-11 SHORT 0J2 1-216-295-11 SHORT 0J5 1-216-296-11 SHORT 0J6 1-216-296-11 SHORT 0J7 1-216-296-11 SHORT 0
J8 1-216-296-11 SHORT 0
< COIL >
L301 1-410-396-41 FERRITE 0.45uHL901 1-411-756-11 INDUCTOR 50uHL902 1-411-756-11 INDUCTOR 50uH
< DIODE >
LED901 8-719-076-62 LED GL5ED60 (POWER/PROTECTOR)
< TRANSISTOR >
Q101 8-729-202-38 TRANSISTOR 2SC3326N-AQ102 8-729-202-38 TRANSISTOR 2SC3326N-AQ103 8-729-014-85 TRANSISTOR 2SA1618-YGRTE85RQ104 8-729-014-87 TRANSISTOR 2SC4207-YGRTE85RQ105 8-729-901-81 TRANSISTOR 2SC2412K-T-146-R
Q106 8-729-901-81 TRANSISTOR 2SC2412K-T-146-RQ107 8-729-140-82 TRANSISTOR 2SA988-PAFAEA
Q108 8-729-184-53 TRANSISTOR 2SC1845-EAQ109 8-729-046-09 TRANSISTOR 2SD1864-RQ110 8-729-026-49 TRANSISTOR 2SA1037AK-T146-RQ111 8-729-207-82 TRANSISTOR 2SC3421-YQ112 8-729-207-89 TRANSISTOR 2SA1358-Y
Q113 8-729-024-80 TRANSISTOR 2SC5100-YQ114 8-729-024-77 TRANSISTOR 2SA1908-YQ115 8-729-184-53 TRANSISTOR 2SC1845-EAQ116 8-729-024-80 TRANSISTOR 2SC5100-YQ117 8-729-024-77 TRANSISTOR 2SA1908-Y
Q118 8-729-184-53 TRANSISTOR 2SC1845-EAQ119 8-729-024-80 TRANSISTOR 2SC5100-YQ120 8-729-024-77 TRANSISTOR 2SA1908-YQ121 8-729-184-53 TRANSISTOR 2SC1845-EAQ201 8-729-202-38 TRANSISTOR 2SC3326N-A
Q202 8-729-202-38 TRANSISTOR 2SC3326N-AQ203 8-729-014-85 TRANSISTOR 2SA1618-YGRTE85RQ204 8-729-014-87 TRANSISTOR 2SC4207-YGRTE85RQ205 8-729-901-81 TRANSISTOR 2SC2412K-T-146-RQ206 8-729-901-81 TRANSISTOR 2SC2412K-T-146-R
Q207 8-729-140-82 TRANSISTOR 2SA988-PAFAEAQ208 8-729-184-53 TRANSISTOR 2SC1845-EAQ209 8-729-046-09 TRANSISTOR 2SD1864-RQ210 8-729-026-49 TRANSISTOR 2SA1037AK-T146-RQ211 8-729-207-82 TRANSISTOR 2SC3421-Y
Q212 8-729-207-89 TRANSISTOR 2SA1358-YQ213 8-729-024-80 TRANSISTOR 2SC5100-YQ214 8-729-024-77 TRANSISTOR 2SA1908-YQ215 8-729-184-53 TRANSISTOR 2SC1845-EAQ216 8-729-024-80 TRANSISTOR 2SC5100-Y
Q217 8-729-024-77 TRANSISTOR 2SA1908-YQ218 8-729-184-53 TRANSISTOR 2SC1845-EAQ219 8-729-024-80 TRANSISTOR 2SC5100-YQ220 8-729-024-77 TRANSISTOR 2SA1908-YQ221 8-729-184-53 TRANSISTOR 2SC1845-EA
Q301 8-729-027-43 TRANSISTOR DTC114EKA-T146Q307 8-729-207-82 TRANSISTOR 2SC3421-YQ308 8-729-207-89 TRANSISTOR 2SA1358-YQ309 8-729-901-81 TRANSISTOR 2SC2412K-T-146-RQ310 8-729-901-81 TRANSISTOR 2SC2412K-T-146-R
Q311 8-729-027-43 TRANSISTOR DTC114EKA-T146Q901 8-729-106-60 TRANSISTOR 2SB1115A-YQQ902 8-729-027-43 TRANSISTOR DTC114EKA-T146Q903 8-729-901-81 TRANSISTOR 2SC2412K-T-146-RQ904 8-729-027-38 TRANSISTOR DTA144EKA-T146
Q905 8-729-027-43 TRANSISTOR DTC114EKA-T146Q906 8-729-027-43 TRANSISTOR DTC114EKA-T146Q907 8-729-202-38 TRANSISTOR 2SC3326N-AQ908 8-729-202-38 TRANSISTOR 2SC3326N-AQ909 6-550-341-01 FET FKV550N
Q910 6-550-341-01 FET FKV550NQ911 6-550-341-01 FET FKV550NQ912 6-550-341-01 FET FKV550NQ913 6-550-341-01 FET FKV550NQ914 6-550-341-01 FET FKV550N
< RESISTOR >
R101 1-216-198-11 RES-CHIP 1K 5% 1/8W
MAIN
15
XM-1652Z
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
R102 1-216-198-11 RES-CHIP 1K 5% 1/8WR103 1-216-837-11 METAL CHIP 22K 5% 1/10WR104 1-216-837-11 METAL CHIP 22K 5% 1/10WR105 1-218-875-11 METAL CHIP 15K 0.5% 1/10WR106 1-216-845-11 METAL CHIP 100K 5% 1/10W
R107 1-216-845-11 METAL CHIP 100K 5% 1/10WR108 1-218-875-11 METAL CHIP 15K 0.5% 1/10WR109 1-216-837-11 METAL CHIP 22K 5% 1/10WR110 1-216-833-11 METAL CHIP 10K 5% 1/10WR111 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R112 1-218-833-11 METAL CHIP 270 0.5% 1/10WR115 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR116 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR117 1-216-206-00 RES-CHIP 2.2K 5% 1/8WR118 1-216-222-00 RES-CHIP 10K 5% 1/8W
R119 1-216-821-11 METAL CHIP 1K 5% 1/10WR120 1-218-891-11 METAL CHIP 68K 0.5% 1/10WR121 1-218-851-11 METAL CHIP 1.5K 0.5% 1/10WR122 1-218-851-11 METAL CHIP 1.5K 0.5% 1/10WR123 1-218-851-11 METAL CHIP 1.5K 0.5% 1/10W
R124 1-218-851-11 METAL CHIP 1.5K 0.5% 1/10WR125 1-218-891-11 METAL CHIP 68K 0.5% 1/10WR126 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR127 1-216-809-11 METAL CHIP 100 5% 1/10WR128 1-216-845-11 METAL CHIP 100K 5% 1/10W
R129 1-216-845-11 METAL CHIP 100K 5% 1/10WR130 1-216-809-11 METAL CHIP 100 5% 1/10WR131 1-218-851-11 METAL CHIP 1.5K 0.5% 1/10WR132 1-216-817-11 METAL CHIP 470 5% 1/10WR133 1-245-855-11 METAL CHIP 13K 0.5% 1/10W
R134 1-216-222-00 RES-CHIP 10K 5% 1/8WR135 1-216-182-00 RES-CHIP 220 5% 1/8WR136 1-216-134-00 RES-CHIP 2.2 5% 1/8WR137 1-216-134-00 RES-CHIP 2.2 5% 1/8WR138 1-205-991-11 METAL 0.1X2 10% 5W F
R139 1-216-134-00 RES-CHIP 2.2 5% 1/8WR140 1-216-134-00 RES-CHIP 2.2 5% 1/8WR141 1-205-991-11 METAL 0.1X2 10% 5W FR142 1-216-134-00 RES-CHIP 2.2 5% 1/8WR143 1-216-134-00 RES-CHIP 2.2 5% 1/8W
R144 1-205-991-11 METAL 0.1X2 10% 5W FR145 1-216-833-11 METAL CHIP 10K 5% 1/10WR146 1-216-134-00 RES-CHIP 2.2 5% 1/8WR147 1-216-841-11 METAL CHIP 47K 5% 1/10WR148 1-216-833-11 METAL CHIP 10K 5% 1/10W
R149 1-216-833-11 METAL CHIP 10K 5% 1/10WR150 1-216-833-11 METAL CHIP 10K 5% 1/10WR151 1-216-833-11 METAL CHIP 10K 5% 1/10WR152 1-216-833-11 METAL CHIP 10K 5% 1/10WR153 1-216-833-11 METAL CHIP 10K 5% 1/10W
R154 1-218-859-11 METAL CHIP 3.3K 0.5% 1/10WR201 1-216-198-11 RES-CHIP 1K 5% 1/8WR202 1-216-198-11 RES-CHIP 1K 5% 1/8WR203 1-216-837-11 METAL CHIP 22K 5% 1/10WR204 1-216-837-11 METAL CHIP 22K 5% 1/10W
R205 1-218-875-11 METAL CHIP 15K 0.5% 1/10WR206 1-216-845-11 METAL CHIP 100K 5% 1/10WR207 1-216-845-11 METAL CHIP 100K 5% 1/10W
R208 1-218-875-11 METAL CHIP 15K 0.5% 1/10WR209 1-216-837-11 METAL CHIP 22K 5% 1/10WR210 1-216-833-11 METAL CHIP 10K 5% 1/10WR211 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR212 1-218-833-11 METAL CHIP 270 0.5% 1/10W
R213 1-216-833-11 METAL CHIP 10K 5% 1/10WR214 1-216-833-11 METAL CHIP 10K 5% 1/10WR215 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR216 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR217 1-216-206-00 RES-CHIP 2.2K 5% 1/8W
R218 1-216-222-00 RES-CHIP 10K 5% 1/8WR219 1-216-821-11 METAL CHIP 1K 5% 1/10WR220 1-218-891-11 METAL CHIP 68K 0.5% 1/10WR221 1-218-851-11 METAL CHIP 1.5K 0.5% 1/10WR222 1-218-851-11 METAL CHIP 1.5K 0.5% 1/10W
R223 1-218-851-11 METAL CHIP 1.5K 0.5% 1/10WR224 1-218-851-11 METAL CHIP 1.5K 0.5% 1/10WR225 1-218-891-11 METAL CHIP 68K 0.5% 1/10WR226 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR227 1-216-809-11 METAL CHIP 100 5% 1/10W
R228 1-216-845-11 METAL CHIP 100K 5% 1/10WR229 1-216-845-11 METAL CHIP 100K 5% 1/10WR230 1-216-809-11 METAL CHIP 100 5% 1/10WR231 1-218-851-11 METAL CHIP 1.5K 0.5% 1/10WR232 1-216-817-11 METAL CHIP 470 5% 1/10W
R233 1-245-855-11 METAL CHIP 13K 0.5% 1/10WR234 1-216-222-00 RES-CHIP 10K 5% 1/8WR235 1-216-182-00 RES-CHIP 220 5% 1/8WR236 1-216-134-00 RES-CHIP 2.2 5% 1/8WR237 1-216-134-00 RES-CHIP 2.2 5% 1/8W
R238 1-205-991-11 METAL 0.1X2 10% 5W FR239 1-216-134-00 RES-CHIP 2.2 5% 1/8WR240 1-216-134-00 RES-CHIP 2.2 5% 1/8WR241 1-205-991-11 METAL 0.1X2 10% 5W FR242 1-216-134-00 RES-CHIP 2.2 5% 1/8W
R243 1-216-134-00 RES-CHIP 2.2 5% 1/8WR244 1-205-991-11 METAL 0.1X2 10% 5W FR245 1-216-833-11 METAL CHIP 10K 5% 1/10WR246 1-216-134-00 RES-CHIP 2.2 5% 1/8WR247 1-216-841-11 METAL CHIP 47K 5% 1/10W
R248 1-216-833-11 METAL CHIP 10K 5% 1/10WR249 1-216-833-11 METAL CHIP 10K 5% 1/10WR250 1-216-833-11 METAL CHIP 10K 5% 1/10WR251 1-216-833-11 METAL CHIP 10K 5% 1/10WR252 1-216-833-11 METAL CHIP 10K 5% 1/10W
R253 1-216-833-11 METAL CHIP 10K 5% 1/10WR254 1-218-859-11 METAL CHIP 3.3K 0.5% 1/10WR301 1-216-198-11 RES-CHIP 1K 5% 1/8WR302 1-216-206-00 RES-CHIP 2.2K 5% 1/8WR303 1-216-845-11 METAL CHIP 100K 5% 1/10W
R304 1-216-845-11 METAL CHIP 100K 5% 1/10WR305 1-216-833-11 METAL CHIP 10K 5% 1/10WR306 1-216-206-00 RES-CHIP 2.2K 5% 1/8WR307 1-218-859-11 METAL CHIP 3.3K 0.5% 1/10WR308 1-218-873-11 METAL CHIP 12K 0.5% 1/10W
R309 1-216-833-11 METAL CHIP 10K 5% 1/10WR310 1-216-845-11 METAL CHIP 100K 5% 1/10WR311 1-218-875-11 METAL CHIP 15K 0.5% 1/10W
MAIN
16
XM-1652Z
Ref. No. Part No. Description Remark
R312 1-218-875-11 METAL CHIP 15K 0.5% 1/10WR313 1-216-837-11 METAL CHIP 22K 5% 1/10WR314 1-216-837-11 METAL CHIP 22K 5% 1/10WR315 1-216-845-11 METAL CHIP 100K 5% 1/10WR316 1-218-901-11 METAL CHIP 180K 0.5% 1/10W
R317 1-216-234-00 RES-CHIP 33K 5% 1/8WR318 1-216-837-11 METAL CHIP 22K 5% 1/10WR319 1-216-821-11 METAL CHIP 1K 5% 1/10WR320 1-216-222-00 RES-CHIP 10K 5% 1/8WR321 1-216-222-00 RES-CHIP 10K 5% 1/8W
R322 1-216-821-11 METAL CHIP 1K 5% 1/10WR901 1-216-206-00 RES-CHIP 2.2K 5% 1/8WR902 1-216-222-00 RES-CHIP 10K 5% 1/8WR903 1-216-833-11 METAL CHIP 10K 5% 1/10WR904 1-216-833-11 METAL CHIP 10K 5% 1/10W
R905 1-216-821-11 METAL CHIP 1K 5% 1/10WR906 1-218-833-11 METAL CHIP 270 0.5% 1/10WR907 1-216-206-00 RES-CHIP 2.2K 5% 1/8WR908 1-216-206-00 RES-CHIP 2.2K 5% 1/8WR909 1-216-833-11 METAL CHIP 10K 5% 1/10W
R910 1-216-837-11 METAL CHIP 22K 5% 1/10WR911 1-218-867-11 METAL CHIP 6.8K 0.5% 1/10WR912 1-216-833-11 METAL CHIP 10K 5% 1/10WR913 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR914 1-216-833-11 METAL CHIP 10K 5% 1/10W
R915 1-216-841-11 METAL CHIP 47K 5% 1/10WR916 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR917 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR918 1-216-813-11 METAL CHIP 220 5% 1/10WR919 1-216-206-00 RES-CHIP 2.2K 5% 1/8W
R920 1-216-190-00 RES-CHIP 470 5% 1/8WR921 1-216-190-00 RES-CHIP 470 5% 1/8WR922 1-216-821-11 METAL CHIP 1K 5% 1/10WR923 1-216-158-00 RES-CHIP 22 5% 1/8WR924 1-216-821-11 METAL CHIP 1K 5% 1/10W
R925 1-216-821-11 METAL CHIP 1K 5% 1/10WR926 1-216-158-00 RES-CHIP 22 5% 1/8WR927 1-216-821-11 METAL CHIP 1K 5% 1/10WR928 1-216-789-11 METAL CHIP 2.2 5% 1/10WR929 1-216-789-11 METAL CHIP 2.2 5% 1/10W
R930 1-216-789-11 METAL CHIP 2.2 5% 1/10WR931 1-216-789-11 METAL CHIP 2.2 5% 1/10WR932 1-216-789-11 METAL CHIP 2.2 5% 1/10WR933 1-216-789-11 METAL CHIP 2.2 5% 1/10WR934 1-216-845-11 METAL CHIP 100K 5% 1/10W
R935 1-216-833-11 METAL CHIP 10K 5% 1/10WR936 1-216-833-11 METAL CHIP 10K 5% 1/10W
< SWITCH >
SW301 1-771-271-11 SWITCH, SLIDE (LPF(80Hz))
< TRANSFORMER >
T901 1-443-569-11 TRANSFORMER, DC-DC CONVERTER
< THERMISTOR >
TH301 1-809-992-21 THERMISTOR NTH5G42B104K02TETH302 1-809-992-21 THERMISTOR NTH5G42B104K02TE
TH303 1-809-992-21 THERMISTOR NTH5G42B104K02TE
< VARIABLE RESISTOR >
VR301 1-225-459-11 RES, VAR, CARBON 10KX2 (LEVEL)*************************************************************
MISCELLANEOUS***************
0F901 1-532-947-11 FUSE (BLADE TYPE) (AUTO FUSE) (30A)0F902 1-532-947-11 FUSE (BLADE TYPE) (AUTO FUSE) (30A)*************************************************************
ACCESSORIES************
2-546-724-11 MANUAL, INSTRUCTION (ENGLISH,SPANISH)(US)
2-546-724-21 MANUAL, INSTRUCTION (ENGLISH,SPANISH,TRADITIONAL CHINESE) (E)
*************************************************************
PARTS FOR INSTALLATION AND CONNECTIONS***************************************
101 3-367-410-11 SCREW (DIA. 5X15), TAPPING(MOUNTING SCREW)
102 1-690-779-31 CORD (WITH CONNECTOR) (0.2m)103 3-249-791-01 COVER (POWER)
Ref. No. Part No. Description Remark
101 102 103
φ 5 × 15 mm(× 4) 0.2 m (8 in)
MAIN
The components identified bymark 0 or dotted line with mark0 are critical for safety.Replace only with part numberspecified.
18
XM-1652Z
REVISION HISTORY
Clicking the version allows you to jump to the revised page.Also, clicking the version at the upper right on the revised page allows you to jump to the next revisedpage.
Ver. Date Description of Revision1.0 2005. 01 New