Technical Specifications:

ZOLL AED 3® WiFi

Operational Bands IEEE 802.11a/b/g/nDual Band: 2.4 & 5 GHz

EncryptionWPA/TKIPWPA/AES (CCMP)WPA2/TKIPWPA2/AES (CCMP)

AuthenticationPSK (Pre-shared Key or ”Personal”)Enterprise Authentication methods (IEEE 802.1X/RADIUS) as follows:• EAP-TLS• PEAPv0/v1-MSCHAPv2

ZOLL AED 3 WiFi Transmission/Setup Error Codes

Error Code Name Explanation

1 ‘AP_UNAVAILABLE’ This error code will be issued if the specified access point is unavailable

2 ‘AP_DHCP This error code will be issued if there is a DHCP error with the specified access point

3 ‘AP_NO_IP_ADDR’This error code will be issued if the ZOLL AED 3 could not get an IP address from the access point

4 ‘AP_AUTH’This error code will be issued if the ZOLL AED 3 could not get authentication with the access point due to an invalid certificate or password

5 ‘AP_ALREADY_CONNECTED’This error code will be issued if the ZOLL AED 3 is trying to connect to an access point while already connected to one

6 ‘AP_INVALID_SSID’ This error code will be issued if the ZOLL AED 3 uses an invalid SSID

7 ‘AP_NO_CONFIG’ Contact ZOLL Technical Support or Local Authorized Distributor

8 ‘AP_NO_SESSION_MGR’This error code will be issued if the ZOLL AED 3 tries to perform a data transfer before the session manager is ready

9 ‘AP_UNDEFINED’This error code will be issued if the ZOLL AED 3 identifies an undefined access point error

When the ZOLL AED 3® is configured to send self-test data to Defibrillator Dashboard™ or PlusTrac™, it will transmit in the following situations:• Following weekly self-test• Following monthly self-test• Following Power Off only if the unit failed the Power Off

self test (transmission will occur 60 seconds after the user powers off the AED.

If the ZOLL AED 3 is not configured to automatically transmit self-test data, users can manually push a self-test from the ‘export’ menu, and the file is labeled Device History.

SSIDBroadcast by APNot broadcast (stealth mode)

Preconfigured ProfilesSoftware Rev. 01.03.203, 02.03.016.5270, and 03.03.008.5508: Two ProfilesSoftware Rev 04.03.500 Forward: Up to 25 Profiles

IP ConfigurationIP v4Dynamic (external DHCP server)Static IP

Root Certificate Key Length (if applicable)2048-bit is supported – default ZOLL Root Cert uses 2048-bit

Error Code Name Explanation

10 ‘SERVER_CERT_VALID’ This error code will be issued if the server determines that the certificate was invalid

11 ‘SERVER_DNS’ This error code will be issued if the ZOLL AED 3 encounters a DNS error resolving the server domain name

12 ‘SERVER_NO_CONFIG’ Contact ZOLL Technical Support or Local Authorized Distributor

13 ‘SERVER_NO_DATA_MGR’ This error code will be issued if the ZOLL AED 3 tries to perform a data transfer before the data manager is ready

14‘SERVER_NOT_CONNECTED

_TO_AP’This error code will be issued if the ZOLL AED 3 tries to connect to server without being connected to an access point

15 ‘SERVER_ALREADY_CONNECTED’ This error code will be issued if the ZOLL AED 3 tries to connect to the server while already connected to the server

16 ‘SERVER_CONNECT_FAILURE’ This error code will be issued if the ZOLL AED 3 encounters an undefined server connection error

© 2018 ZOLL Medical Corporation. All rights reserved. Defibrillator Dashboard, PlusTrac, ZOLL AED 3 and ZOLL are trademarks or registered trademarks of ZOLL Medical Corporation in the United States and/or other countries.

MCN PP 1803 0344

ZOLL AED 3® WiFi Transmission/Setup Error Codes

Wi-Fi Setup to PlusTrac

STEP 1 Turn on ZOLL AED 3 DefibrillatorPress and hold the On/Off button in the upper left for 30 seconds

STEP 2 Select Configuration Mode

On/Offbutton

On/Off button

Select Operating Mode

Device ID Unit OK 08:33 AMi

Configuration

AX00J000000 08:33 AMi

Enter Supervisor Passcode

Cancel OK

1 2 3 4 5

6 7 8 9 0

123456

Press the button with the picture of gears

STEP 3 Once in Configuration Mode Press Unlock Click the orange button with the picture of the lock

Configuration Mode

Unlock

STEP 4 Enter the Supervisor Passcode Default code is 1 2 3 4 5 6 and select OK

Configuration

AX00J000000 08:33 AMi

Status Update

Searching for wirelessnetworks.

Device History Quick Settings

Test Wi-Fi Cancel

Network (SSID)

Password (Pre-Shared Key)

Server Settingsdxsvc.zollonline.com1507131812495EITZExLUu

Save

Edit

Select Wi-Fi Setup Level

Quick Setup IT Setup

Please select the desired Wi-Ficonfiguration setup.

STEP 5 Enter the Wi-Fi Setup menuPress the icon with the ZOLL AED 3

STEP 6 Select the Wi-Fi Level Press Quick Setup button

STEP 7 Once in Setup Mode Press Wi-Fi icon Click the green button to seach for available networks

Wi-Fi Setup

Wi-Fi search

STEP 8 Wait for the AED 3 to find signal Search may take a minute

Status Update

Testing server connectivity.

Enter Pre-Shared Key

Cancel OK

123456q w e r t y u i o p

a s d f g h j k l

z x c v b n m .

ABC 123

Device History Quick Settings

Test Wi-Fi Cancel

Network (SSID)

Password (Pre-Shared Key)

Server Settingsdxsvc.zollonline.com1507131812495EITZExLUu

Save

ZOLLAED3

123456

Edit

Stelect Network

Cancel OK

Select NetworkZOLLAED3Sample Network

^

STEP 9 Choose the correct network from the listPress OK if Network is found, if no network type the name

STEP 10 Enter the Password for your Network Type the pass key into the box using the keyboard and press OK

STEP 11 Testing your Wi-Fi Network After Setup is complete you can test your connection

Select your Wi-Fi Network

STEP 12 When Test is Complete you are READY! Your AED 3 can now communicate to PlusTrac

STEP 13 Log on to the PlusTrac2.com websiteEnter the User Name (email address) and Password provided(new customers will need to complete “Activation” and registration)

STEP 14 Accessing your Device History Press the Equipment Tab on the left Menu Bar

EquipmentTab

STEP 15 Viewing the AED 3 information cardClick the Blue Arrow to Expand the Card and review information

STEP 16 Selecting the Device History Press the Blue text that reads “History” on the Card

DeviceHistory

Expand Card

STEP 17 Viewing the AED 3 communicationYou will see a list of all the information sent from the AED 3.Select the event you want to view by clicking the Blue Text

STEP 18 Understanding the Device History PlusTrac record the communication of the AED 3 and will send Email alerts for any actions that need to be taken

Self Test Results