CTA
: 142
584
1425
84
Amsler HIT1100F drop weight tester Amsler HIT1100F drop weight tester, detail view
The Amsler HIT1100F and Amsler HIT2000F weredeveloped for testing components. They featuremodular design and can optionally be
equipped with acceleration unit and temperaturechamber. These drop weight testers offer exceptionalflexibility.
Range of application• Component testing• Puncture tests on plastics to ISO 6603-2 and ASTM
D3763• Accelerated puncture tests on plastics in accordance
with various automotive standards• Puncture tests on plastic films to ISO7765-2, ASTM
D7192, ASTM D4272
• Charpy tests to ISO 179-2• Izod tests to ISO 180 and ASTM D256
Advantages and featuresReliable test results
• Sturdy guides make these drop weight testers idealfor testing components.
• High natural measuring frequency enables accuratetest results.
Flexibility• T-slotted mounting platforms allow flexible attachment
of various test arrangements.• These drop weight testers can optionally be equipped
with a temperature chamber and an acceleration unit.
ZwickMaterials testing
Product InformationAmsler HIT 1100F/HIT 2000F drop weight testers
PI 9
40 0
917
Technische Daten zum Grundgerät Amsler HIT1100F / HIT2000F
Item No. 1050792 1050814
Maximum energy 275 440 J
Dimensions
Height 3270 3870 mm
Width 1400 1400 mm
Depth 920 920 mm
Drop height, maximum 1 1,5 m
Drop height, minimum 0,05 0,05 m
Drop mass, maximum 29,4 29,4 kg
Drop mass, minimum 9,3 9,3 kg
Drop velocity, maximum 4,4 5,4 m/s at 1 m dropheight
Force signal resolution 16 16 bits
Measured-value rate (force signal), maxi‐mum
3 3 MHz
Clamping force 100 100 N
Weight 1450 1600 kg
Compressed air supply
Supply pressure 6 6 bar
Air consumption, approx. 10 20 l/impact
Required air-supply output-rate 600 600 l/min
Service unit mounted on instrument mounted on instrument
Required floor load capacity 20 20 kN/m²1)
Leveling feet concentrated load 150 166 N/cm²
Electrical supply data
Electrical supply 230 230 V (1 Ph, N, PE)
Power consumption (pre-load), approx. 16 16 A
1) It depends on the peak dynamic force the can be achieved
Accessories required
Tup-holder and weightsDescription Item number
Tup-holder with modular weight set up to 30 kg,comprising the following weight steps: 9,3 kg to 29,4 kg in 1kg steps
1050795
Mounts for clamping ringsDescription Item number
Mount for clamping rings for ISO and ASTM specimens(pneumatic clamping, temperature range -40 to 70°C)
1050857
Mount for clamping rings for ISO and ASTM specimens(manual clamping, temperature range -70 to 140°C)
1050858
ZwickMaterials testing
Product InformationAmsler HIT 1100F/HIT 2000F drop weight testers
We reserve the right to make technical changes in the course of ongoingdevelopment.
All data at ambient temperature.
Clamping rings
TypeInside diameter[mm] Clamping faces
Scope of delivery[pair] Item No.
Clamping rings as perISO 6603-2
20 grooved 1 1050797
Clamping rings as perISO 6603-2
40 grooved 1 1050796
Clamping rings as perASTM D3763
76 grooved 1 1050798
Clamping rings as perISO 7765-2
40 smooth 1 1050800
Force sensors
• Easily interchangeable• Replaceable tips• Guarded axial terminal for measuring lead
StandardDiameter[mm]
Max. force[kN] Item No.
ISO 6603-2 10 9 1050802
ISO 6603-2 20 15 1050801
ASTM D3763 12.7 (I/2") 15 1050803
Charpy and Izod testing equipmentA set of testing equipment consists of a basic mount, test fixture, load cell and striker.
Description Item number
Basic mount for Charpy and Izod test fixtures 1050806
Charpy test fixture1)
- for tests to ISO179-1/-2- incl. specimen centering
1050807
Izod test fixture1)
- for tests to ISO 180- incl. specimen centering
1050808
Tup incl. Piezo load cell, Fmax. 10kN, for Charpy and Izod 1050810
Striker as per ISO179-1/-2 (Charpy)2) 1050811
Striker as per ISO 180 (Izod) 2) 1050812
1) Required: basic mount for Charpy and Izod test fixtures2) Required: piezo load cell, Fmax. 10kN, for Charpy and Izod strikers
Optional accessories
Acceleration unit for Amsler HIT 1100FFor higher speeds and energies
ZwickMaterials testing
Product InformationAmsler HIT 1100F/HIT 2000F drop weight testers
We reserve the right to make technical changes in the course of ongoingdevelopment.
All data at ambient temperature.
• Easy to operate with Zwick Roell testing software
Description Item number
Acceleration unit for Amsler HIT1100F- Maximum impact velocity at 29,4 kg: 8,75 m/s- Maximum energy at 29,4 kg: 1126 J- Maximum impact velocity at 9,3 kg: 14,1m/s- Maximum energy at 9,3 kg: 926 J
1050793
Acceleration unit for Amsler HIT 2000FFor higher speeds and energies
• Easy to operate with Zwick Roell testing software
Description Item number
Acceleration unit for Amsler HIT2000F- Maximum impact velocity at 29,4 kg: 11,8 m/s- Maximum energy at 29,4 kg: 2044 J- Maximum impact velocity at 9,3 kg: 19,4 m/s- Maximum energy at 9,3 kg: 1745 J
1050815
Temperature chamberFor tests at low and high temperatures
Description Item number
Temperature chamber for Amsler HIT1100F and Amsler HIT2000F- Internal dimensions 400x400x400mm- Temperature range -70 to 180°C- LN² required for cooling
1050794
ZwickMaterials testing
Product InformationAmsler HIT 1100F/HIT 2000F drop weight testers
We reserve the right to make technical changes in the course of ongoingdevelopment.
All data at ambient temperature.