2.2) Network RTK – Rover setting for Network RTK (GSM) [1]

1. Power on

2. Press “F1” to select “Survey”

3. Press “ENTER” to select Config Set

1

32

AlternativesYou may direct select “6. Configure” in procedure 2 and it will jump to the procedure 4.

2.2) Network RTK – Rover setting for Network RTK (GSM) [2]

4 54. Select “RT_ROV” default

template and press “F2” to make a New config set

5. Give a name for the new config set – Net_RTK, and Press “F1” to continue

2.2) Network RTK – Rover setting for Network RTK (GSM) [3]

67

6. Press “F3” to edit “Net_RTK”

7. Press “ENTER” to select “Advanced” Mode and press “F1” to continue

2.2) Network RTK – Rover setting for Network RTK (GSM) [4]

8

8. Press “ENTER” to select a suitable Ant. Name for your project and press “F1” to Continue

9. Select the Update Rate (0.1s) and Coordinate Sys. (WGS84 Geodetic), Press “F1” to continue

Remark:If you want to increase the accuracy in heighting, then you should transfer the coordinate system [2_Step_(212_2005)] to the rover so that you can select here.

9

Ellipsoid : WGS 1984

2.2) Network RTK – Rover setting for Network RTK (GSM) [5]

10 11 Press “F1” to confirm the default setting

2.2) Network RTK – Rover setting for Network RTK (GSM) [6]

1213

12.Select “Rover” for the Real Time Data

13.Press “ENTER” to select the “Data Format”

2.2) Network RTK – Rover setting for Network RTK (GSM) [7]

RTCM

14.Choose “RTCM 20, 21”for the Data Format

15.Press “F4” to Configure the RTCM Format14 15

2.2) Network RTK – Rover setting for Network RTK (GSM) [8]

RTCM Versn : 2.1#Bits/Byte : 6

RTCM

RTCM REF

1617

16.Select RTCM Version “2.1” and #Bits/Byte “6”and press “F1” to continue

17.Press “F6” to setup the Reference Service for RTCM type 20, 21

2.2) Network RTK – Rover setting for Network RTK (GSM) [9]

Ref Service : VRSSend User ID : NO

RTCM

RTCM REF

1819

18.Select “VRS” for Ref Service and “NO” for Send User ID, press “F1”to continue

19.Press “F5” to setup the Device and Ports

2.2) Network RTK – Rover setting for Network RTK (GSM) [10]

1 *Siemens M20

ADVNULLANTENNA

Use Phase : YES Radio Down : Don’t Log Obs

RTCM REF

2021

20.Select “*Siemens M20”

21.Select “Unknown” for Ref Sensor, “ADVNULLANTENNA” for Ref Antenna, “YES” for Use Phase, “Don’t Log Obs” for Radio Down and press “F1” to continue

2.2) Network RTK – Rover setting for Network RTK (GSM) [11]

22

23

22.Press “ENTER” to input Station name

23.Press “NEW” to make a new station

2.2) Network RTK – Rover setting for Network RTK (GSM) [12]

ConnElement : Non-TransparentNetDataRate :24

24. Input “35120000” to connect with the Server and select “Analog”Mode

25.Follow up the setting shown on the screen captured

25

2.2) Network RTK – Rover setting for Network RTK (GSM) [13]

OCUPY Mode: NormalAuto OCUPY: NOAuto Stop: NOSTOP R-TME: NoneSTOP Store: NOEND Survey: Manual

Press “F1” to confirm the default setting26

2.2) Network RTK – Rover setting for Network RTK (GSM) [14]

Auxil Pts : No Template Used

Avg/Abs Diffs : AvgAvg. Limits Pos : 0.050 mAvg. Limits Hgt : 0.070 mMonitor CQ : Pos + HeightQuality : 0.050 m

DOP

27

Press “F1” to confirm the default setting

2.2) Network RTK – Rover setting for Network RTK (GSM) [15]

Include Hgt : NoPos Quality : 0.100 m

Hidden Point

IFACE

Stake from : JobShow Path : NoUse Beep : YESDist from Pt : 0.500 mDiff Check : Pos + Hgt

Stake-Out

28Press “F1” to confirm the default setting

2.2) Network RTK – Rover setting for Network RTK (GSM) [16]

Use Seismic Record : No

Seismic

29

Press “F1” to continue