FOREWORD - Team-BHP

FOREWORDThis manual is an essential part of yourvehicle and should remain with the vehiclewhen resold or otherwise transferred to anew owner or operator. Please read thismanual carefully before operating yournew MARUTI SUZUKI and review themanual from time to time. It containsimportant information on safety, operationand maintenance. You are invited to availthe three Free Inspection Services asdescribed in the manual. Three freeinspection coupons are attached to thismanual. Please show this manual to yourdealer workshop while you take yourMARUTI SUZUKI for any Service.To prolong the life of your vehicle andreduce maintenance cost, the periodicmaintenance must be carried out accord-ing to “PERIODIC MAINTENANCESCHEDULE” described in “INSPECTIONAND MAINTENANCE” section of this man-ual. It is essential for preventing troubleand accidents to ensure your satisfactionand safety.Daily inspection and care as per “DAILYINSPECTION CHECKLIST” described inthe “OPERATING YOUR VEHICLE” sec-tion of this manual is essential for prolong-ing the life of the vehicle and for safedriving.

MARUTI SUZUKI INDIA LIMITED believesin conservation and protection of Earth’snatural resources.To that end, we encourage every vehicleowner to recycle, trade-in or properly dis-pose of, as appropriate, used Engine Oil,coolant and other fluids, batteries andtyres etc.

MARUTI SUZUKI INDIA LIMITED

All information in this manual is basedon the latest product information avail-able at the time of publication. Due toimprovements or other changes, theremay be discrepancies between informa-tion in this manual and your vehicle.MARUTI SUZUKI INDIA LIMITEDreserves the right to make productionchanges at any time, without notice andwithout incurring any obligation tomake the same or similar changes tovehicles previously built or sold.

This vehicle may not comply with stan-dards or regulations of other countries.Before attempting to register this vehi-cle in any other country, check all appli-cable regulations and make any neces-sary modifications.

IMPORTANTWARNING/ CAUTION/NOTICE/

NOTEPlease read this manual and follow itsinstructions carefully. To emphasize spe-cial information, the symbol and the wordsWARNING, CAUTION, NOTICE andNOTE have special meanings. Pay partic-ular attention to messages highlighted bythese signal words:

NOTE:Indicates special information to makemaintenance easier or instructions clearer.

75F135

The circle with a slash in this manualmeans “Don’t do this” or “Don’t let this hap-pen”.

MODIFICATION WARNING

WARNING

Indicates a potential hazard thatcould result in death or seriousinjury.

CAUTION

Indicates a potential hazard thatcould result in minor or moderateinjury.

NOTICE

Indicates a potential hazard thatcould result in vehicle damage.

WARNING

Do not modify your vehicle. Modifica-tion could adversely affect safety,handling, performance, or durabilityand may violate governmental regula-tions. In addition, damage or perfor-mance problems resulting frommodification may not be coveredunder warranty.

NOTICE

Improper installation of mobile commu-nication equipment such as cellulartelephones, CB (Citizen’s Band) radiosmay cause electronic interference withyour vehicle’s ignition system, result-ing in vehicle performance problems.Consult your Maruti Suzuki authorisedworkshop or qualified service techni-cian for advice on installing suchmobile communication equipment.

NOTICE

The diagnostic connector of yourvehicle is prepared only for the spe-cific diagnostic tool for inspectionand service purpose. Connecting anyother tool or device may interferewith electronic parts operations andcause running out of batteries.

Vehicle may , meet with an or due to

1. Installation of- High wattage bulbs- Non genuine lamps / horns- Modified suspension / wheels- Non genuine parts / accessories etc.

2. Retrofitment of LPG / CNG fuel systems/kits.

3. Usage of domestic LPG.

4. Short circuiting due to tampering of wiring harness.

CAUTION: DO NOT STORE OR CARRY INFLAMMABLE MATERIALS IN THE VEHICLE.

break-downaccident catch fire

Avoid driving into or starting the vehicle in a heavily water logged area. Vehicle may break-down or engine may fail due to

1. Water entry into the engine.

2. Short circuiting of the electrical systems.

If the vehicle is stuck in deep water, start / crank the vehicle until the level of water drops below the level of exhaust pipe.

NOTE:IF THE VEHICLE IS SUBMERGED IN WATER, REPORT TO THE NEAREST AUTHORIZED WORKSHOP.

do not

“WARNING”

1. Retro-fitment of LPG / CNG kit may deteriorate vehicle performance, reduce engine & enginerelated component’s life and also warranty will be null and void for such vehicles.

2. Do not use domestic LPG/LPG cylinder for your factory fitted LPG vehicles.3. Usage of domestic LPG for running vehicles is prohibited as per law.4. Do not remove company fitted LPG/CNG kit to install some other kit. It may affect vehicle

performance and may cause fire.5. Drive slowly on wet roads. Tires may slip while braking at higher speeds due to aquaplaning.

(reduced contact area between tire and road due to presence of water)6. Do not leave engine running in garages or confined areas, with passengers inside. This may result in

accumulation of carbon-monoxide in cabin and may lead to suffocation or breathing problems.7. Do not park vehicle on dry leaves or grass. This may lead to fire due to hot catalytic converter,

igniting the dry leaves/grass.8. If the vehicle is equipped with CNG/LPG, ensure availability of fire extinguisher in the vehicle all the time.9. Always wear seat belt at all the times.10.Do not use mobile phone while driving.11.Avoid Smoking in the car, live bud thrown in car may cause fire.12.Do not put any body part under the vehicle when it is supported on a Jack.13.Do not use non-genuine accessories in your vehicle.14.Do not fit accessories from unauthorized workshops/sources.15.Usage of non-approved electrical accessories in your vehicle may result in spark, fire or personal

injury.

“CAUTION”

VIN:MODEL:

OWNERNAME & ADDRESS

VARIANT:

COLOUR:

ENGINE NO.: CONTACT NO.

KEY NO.: E-mail ID:

INVOICE DATE:SELLING DEALER NAME & CODE

ODOMETER READING KM

REGISTRATION NO.:

BATTERY MAKE:DEALER SHOWROOM ADDRESS & CONTACT NO. (STAMP)

BATTERY NO.:

BATTERY BATCH

TYRE MAKE BATCH CODE

Front Right

CONTACT NO. FOR SERVICE APPOINTMENT & SUPPORT

Front Left

Rear Right

Rear Left

Spare

For any assistance with regard to our product, please contact General Manager/Works Manager at any of our Maruti Suzuki authorised Nexadealer / Maruti Suzuki authorised workshop. For additional enquiry you may contact our Regional Office or Service Department. Theaddresses and phone numbers are given in Service Network section of this Manual.

CUSTOMER SERVICE MAINTENANCE RECORD (to be filled by customer)INSPECTION SCHEDULE DATE OF SERVICE MILEAGE (KM) NAME OF SERVICING WORKSHOP

1st Free inspection service - 1000 KM / 1 Months

2nd Free inspection service - 5000 KM / 6 Months

3rd Free inspection service - 10000 KM / 12 Months

1st Paid inspection service - 20000 KM / 24 Months

2nd Paid inspection service - 30000 KM / 36 Months

3rd Paid inspection service - 40000 KM / 48 Months

4th Paid inspection service - 50000 KM / 60 Months









Maruti Suzuki Network can be viewed by installing below Mobile Apps:

For Arena Models; For Nexa Models;

Maruti care Nexa

1ST. FREE INSPECTION COUPON (Customer’s copy) (1,000 KM or 1 MONTH)

COST OF MATERIALS AND CONSUMABLES TO BEBORNE BY CUSTOMER

1ST. FREE INSPECTION COUPON (Selling dealer copy) (1,000 KM or 1 MONTH)


1ST. FREE INSPECTION COUPON (Servicing W/S copy) (1,000 KM or 1 MONTH)


Model Name

Model Code*

VIN

Engine No.

Mileage

Invoice Date

Date of Inspection

Registration No.

Customer Name

Ph. No.

Service workshop / MASS Code (fill below)

Workshop In charge Signature

Model Name

Model Code*

VIN

Engine No.

Mileage

Invoice Date

Date of Inspection

Registration No.

Customer Name

Ph. No.



Model Name

Model Code*

VIN

Engine No.

Mileage

Invoice Date

Date of Inspection

Registration No.

Customer Name

Ph. No.



—— —— ——

For periodic maintenance schedule, refer to “Inspection and Maintenance” section of this manual

D D M M Y YD D M M Y Y



1ST. FREE INSPECTION COUPON (Servicing W/S copy) (1,000 KM or 1 MONTH)

For Servicing Workshop1. Please Fill up Model codes correctly.2. Please fill up Complete VIN. 3. Please fill up customer name and Phone No.

details legibly and correctly for the latest owner. 4. Free service coupon of selling dealer not

operational at present, should be sent to MSIL onmonthly basis.

Service Division Maruti Suzuki India Limited

1ST. FREE INSPECTION COUPON (Selling dealer copy) (1,000 KM or 1 MONTH)





1ST. FREE INSPECTION COUPON (Customer’s copy) (1,000 KM or 1 MONTH)





Stamp of Selling dealer (Code & Full Address)



FOR BAR CODE FOR BAR CODE FOR BAR CODE

2ND. FREE INSPECTION COUPON (Customer’s copy) (5,000 KM or 6 MONTHS)


2ND. FREE INSPECTION COUPON (Selling dealer copy) (5,000 KM or 6 MONTHS)


2ND. FREE INSPECTION COUPON (Servicing W/S copy (5,000 KM or 6 MONTHS)


Model Name

Model Code*

VIN

Engine No.

Mileage

Invoice Date

Date of Inspection

Registration No.

Customer Name

Ph. No.



Model Name

Model Code*

VIN

Engine No.

Mileage

Invoice Date

Date of Inspection

Registration No.

Customer Name

Ph. No.



Model Name

Model Code*

VIN

Engine No.

Mileage

Invoice Date

Date of Inspection

Registration No.

Customer Name

Ph. No.




—— —— ——




2ND. FREE INSPECTION COUPON (Servicing W/S copy) (5,000 KM or 6 MONTHS)





2ND. FREE INSPECTION COUPON (Selling dealer copy) (5,000 KM or 6 MONTHS)

For Servicing Workshop1. Please Fill up Model codes correctly.

2. Please fill up Complete VIN. 3. Please fill up customer name and Phone No.




2ND. FREE INSPECTION COUPON (Customer’s copy) (5,000 KM or 6 MONTHS)









3RD. FREE INSPECTION COUPON (Customer’s copy) (10,000 KM or 12 MONTHS)


3RD. FREE INSPECTION COUPON (Selling dealer copy) (10,000 KM or 12 MONTHS)


3RD. FREE INSPECTION COUPON (Servicing W/S copy) (10,000 KM or 12 MONTHS)


Model Name

Model Code*

VIN

Engine No.

Mileage

Invoice Date

Date of Inspection

Registration No.

Customer Name

Ph. No.



Model Name

Model Code*

VIN

Engine No.

Mileage

Invoice Date

Date of Inspection

Registration No.

Customer Name

Ph. No.



Model Name

Model Code*

VIN

Engine No.

Mileage

Invoice Date

Date of Inspection

Registration No.

Customer Name

Ph. No.



—— —— ——





3RD. FREE INSPECTION COUPON (Servicing W/S copy) (10,000 KM or 12 MONTHS)





3RD. FREE INSPECTION COUPON (Selling dealer copy) (10,000 KM or 12 MONTHS)

For Servicing Workshop1. Please Fill up Model codes correctly.

2. Please fill up Complete VIN. 3. Please fill up customer name and Phone No.




3RD. FREE INSPECTION COUPON (Customer’s copy) (10,000 KM or 12 MONTHS)









WARRANTY POLICY

Maruti Suzuki India Limited (hereinafter called “Maruti Suzuki”),warrants that each new Maruti Suzuki vehicle distributed in Indiaby Maruti Suzuki and sold by a Maruti Suzuki authorised dealerwill be free, under normal use and service, from any defects inmaterial and workmanship at the time of manufacture SUBJECTTO THE FOLLOWING TERMS AND CONDITIONS:

(1) Qualification:To qualify for this warranty the vehicle must be delivered by aMaruti Suzuki authorised dealer and set-up, and serviced by aMaruti Suzuki authorised workshop.

(2) Term:The term of the warranty shall be twenty-four (24) months or40,000 kilometers (whichever occurs first) from the date ofinvoice to the first owner.

(3) Maruti Suzuki Warranty Obligation:If any defect(s) should be found in a Maruti Suzuki vehicle withinthe term stipulated above, Maruti Suzuki’s only obligation is torepair or replace at its sole discretion any part shown to be defec-tive, with a new part or the equivalent at no cost to the owner forparts or labour, when Maruti Suzuki acknowledges that such adefect is attributable to faulty material or workmanship at the timeof manufacture. Such defective parts, which have been replaced,will become the property of Maruti Suzuki. The owner is responsi-ble for any repair or replacements which are not covered by thiswarranty. The decision of Maruti Suzuki shall be final & binding.

(4) Limitation:

This warranty shall not apply to:

(a) Normal maintenance service required other than the threefree services, including without limitation, oil and fluidchanges, Consumables, headlight aiming, fastener retighten-ing, wheel balancing, wheel alignment and tyre rotation,cleaning of injectors, adjustments of clutch and valve clear-ance.

(b) The normal wear of parts including without limitation, bulbs,tyres and tubes, spark plugs, belts, hoses, filters, wiperblades, brushes, contact points, fuses, clutch disc, brakeshoes, brake pads, cable and all rubber parts (except oil sealand glass run).

(c) Any vehicle which has been used for competition, rallies orracing.

(d) Any repairs or replacement arising from accidents or colli-sion.

(e) Any defect/ damage caused by misuse, negligence, abnor-mal use, insufficient care, vandalism, theft, riot, fire, flooding -not limited to entry of water in the components resulting inengine seizure, hydrostatic lock, etc. or external damages tothe body/ components.

(f) Any damage resulting due to usage of adulterated fuel/ lubri-cants/ oil/ coolant/ fluids/ polishing products and fuel/ lubri-cants/ oil/ coolant/ fluids used other than those specified inthe Owner’s Manual.

(g) Any vehicle which has been modified or altered, includingwithout limitation, the installation of performance accessories,enlargements of lights, other changes and external/ conse-quential reasons.

(h) Any vehicle on which parts or accessories not approved byMaruti Suzuki (Non-MSGA, Non-MSGP) have been used.

(i) Any vehicle which has not been operated in accordance withthe operating instructions in this Owner’s Manual and ServiceBooklet.

NOTICE

Maruti Suzuki offers warranty of sixty (60) months or1,00,000 kilometers (whichever occurs first) for Lithium-ion battery & Integrated Starter Generator (ISG) in petrolmodel from the date of invoice to the first owner.

(j) Any vehicle which has not received the service inspectionsprescribed in this Owner’s Manual and Service Booklet.

(k) Any vehicle which has been assembled, disassembled,adjusted or repaired by other than a Maruti Suzuki authorisedworkshop.

(l) Any vehicle which has been used for purposes other thanwhat it was designed for.

(m) Any damage or deterioration caused by airborne fallout,industrial fallout, acid rain, hail or hail storm, wind storm,lightning, bird droppings, rodents bite / rat bite and such otherthing that result in damage to the vehicle.

(n) Insignificant defects which do not affect the function of thevehicle including without limitation, sound, vibration and fluidseep.

(o) Any natural wear and tear including without limitation, ageing,wear & tear or deterioration such as discoloration, fading,deformation or blurring and fabric discoloration.

(p) Installation and usage of domestic LPG gas/LPG Cylinder.(q) V-belts, hoses and gas leaks.(r) Any vehicle retrofitted with LPG/CNG kits.(s) Repainting including patchwork, bodywork and mouldings

and interior trims.(t) Corrosion, rusting of body parts and/ or components.(u) Any vehicle on which odometer has been changed unautho-

risedly or odometer reading has been modified/ tamperedwith/ or not matching the service records.

(v) The damage(s) caused to the vehicle being unattendeddespite knowledge that the defect exists and ignorance bythe owner/ user of the vehicle.

(w) Any damage(s) caused to vehicle including battery/ tyre dueto parking of the vehicle in idle condition for long duration oftime periods.

(5) Extent of Warranty:This warranty is the entire written warranty given by Maruti Suzukifor Maruti Suzuki vehicles and no dealer or its or his agent oremployee is authorised to extend or enlarge this warranty and nodealer or its or his agent or employee is authorised to make anyoral warranty or representation or assurance on behalf of MarutiSuzuki.Maruti Suzuki reserves the right to add any improvements orchange the design of any model at any time with no obligation tomake the same changes on units previously sold.

(6) Warranty Service:To obtain warranty service, the complete vehicle must be pre-sented at the owner’s expenses to Maruti Suzuki authorised work-shop.The customer shall be responsible for his belongings or accesso-ries fitted in the vehicle at the time of presenting the vehicle forservice and no claim shall be entertained in any manner under anycircumstances.

(7) Owner’s Warranty Responsibilities:It is responsibility of each owner to:

– Have performed, at his own expenses, by a Maruti Suzukiauthorised workshop all the service inspections specified inthe Maruti Suzuki “Owner’s Manual and Service Booklet” andmaintain adequate proof that such service inspections havebeen performed.

– Update and maintain the 'Customer service maintenancerecords' page in the “Owner’s Manual and Service Booklet”,whenever service inspection or warranty service is carried outon the vehicle in a Maruti Suzuki authorised workshop.

– Present the Maruti Suzuki “Owner’s Manual and ServiceBooklet” to the Maruti Suzuki authorised workshop wheneverrequesting service inspections or warranty service.

If the “Owner’s Manual and Service Booklet” should be lost ordestroyed the owner should consult the Maruti Suzuki authoriseddealer from whom the vehicle was purchased for instructions con-cerning replacement of the “Owner’s Manual and Service Book-let”.

(8) Disclaimer of Consequential Damage:Maruti Suzuki assumes no responsibility for loss of vehicle, loss oftime, inconvenience or any other indirect incidental or consequen-tial damage resulting from the vehicle not being available to theowner because of any defect covered by this warranty.

(9) Change of OwnerEven if ownership of the vehicle changes, the remaining warrantyperiod is effective for the new owner.

EMISSION WARRANTY POLICY

Maruti Suzuki offers the Emission Warranty on all Maruti Suzukivehicles (apart from the Regular Warranty and will run parallel tothe regular product warranty) only in four metropolitan cities (NewDelhi, Kolkata, Mumbai and Chennai) with effect from July 1st,2001.

Terms:The Emission Warranty will be applicable for 80,000 kms or 3years (Whichever comes earlier) from the date of invoice to thefirst owner. The remaining warranty terms will be valid in case ofany change in ownership provided the production of all valid docu-ments.

Conditions:1. Under Emission Warranty, Warranty claims will be admitted for

a prima-facie examination, in case vehicle fails to meet theEmission Standard as specified in sub rule (2) of rule no. 115 ofCentral Motor Vehicles Rules (CMVR), 1989.

2. The warranty claims will only be accepted after examinationcarried out by Maruti Suzuki or Maruti Suzuki authorised work-shop which leads to firm conclusions that thea) Original settings have not been tampered in any case. b) Part (as given in Annexure - A) has a manufacturing defect. c) Vehicle is unable to meet the Emission Standards (as given

in 1.), inspite of the vehicle having been maintained andused in accordance with the instructions as specified inOwner’s Manual and Service Booklet and the used fuel anddifferent oils (Engine oil, Transmission oil, Brake oil etc.) arealso as per specification.

3. The method of examination for deciding the warranty of theparts will be at the sole discretion of Maruti Suzuki and MarutiSuzuki authorised workshop and results of the examination willbe final and binding. If after examination, the warrantable con-dition is not established, Maruti Suzuki and Maruti Suzukiauthorised workshop has the right to charge all, or part of thecost of such examination.

4. Under Emission Warranty, the parts (as given in Annexure - A)will be changed free of cost, but the consumables will becharged as per actual.

5. If the part covered under Emission Warranty or the associatedparts, are not independently replaceable, on account of thesebeing integral parts of a complete assembly, Maruti Suzuki andMaruti Suzuki authorised workshop will have the sole discre-tion to replace either the entire assembly or by using some ofthe parts of the system through suitable repairs or modifica-tions.

6. Any consequential repairs or replacement of parts which maybe found necessary to establish compliance of Emission War-ranty, will not be considered under warranty, unless the sameis under product warranty. The consumable will be charged asper actual under such repair or replacement.

7. Maruti Suzuki will not be responsible for the cost of transporta-tion of the vehicle to the nearest Maruti Suzuki authorisedworkshop or any loss due to non-availability of the vehicleduring the period of lodging of a warranty claim and examina-tion and/or repair by Maruti Suzuki authorised workshop.

8. Maruti Suzuki will not be responsible for any penalty that maybe charged by statutory authorities on account of failure tocomply with the EMISSION STANDARDS.

9. Emission Warranty will not be affected by the change of owner,provided all the documents are available.

10. All maintenance actions (as specified in the Owner’s Manualand Service Booklet) need to be followed and recorded in themanual for emission warranty.

11. The customer needs to produce the PUC (Pollution UnderControl) certificate valid for the period preceding the testduring which the failure is discovered. The receipts (for themaintenance of the vehicle as per specification in Owner’sManual and Service Booklet from the date of original purchaseof the vehicle) will also be required.

Conditions under which the Emission Warranty is notAPPLICABLE1. In the absence of valid PUC certificate.

2. Vehicle not serviced from Maruti Suzuki authorised workshopas per the schedule specified in the Owner’s Manual.

3. Vehicle subjected to abnormal use (accident, motor race, ral-lies or for the purpose of establishing the records etc).

4. Use of non MSGP (Maruti Suzuki Genuine Part).

5. Vehicle that has been tampered with.

6. Tampering with odometer so that the actual kilometer readingcannot be determined.

7. Use of adulterated fuel and/or unspecified oils (Engine oil,Transmission oil and Brake oil etc).

Annexure - AList of parts (if applicable) covered under Emission Warranty1. Fuel Injection Assembly, Pressure Regulator, Throttle Body

Assembly.2. Electronic Control Module (ECM).3. Intake Manifold.4. EGR valve.5. Ignition Coil.6. Canister Assembly.7. Vapour Liquid Seperator.8. Fuel Tank and Filler Cap.9. PCV (Positive Crankcase Ventilation) Valve.10. Oil Filler Cap.11. Catalytic Convertor.12. Exhaust Manifold.13. All Fuel Injection System related Sensors.14. High Pressure Fuel Pump.15. Glow Plug.16. Glow Plug Controller.

69RH0-74E

TABLE OF CONTENTS FOR SAFE DRIVING 1

BEFORE DRIVING 2

OPERATING YOUR VEHICLE 3

DRIVING TIPS 4

OTHER CONTROLS AND EQUIPMENT 5

INSPECTION AND MAINTENANCE 6

EMERGENCY SERVICE 7

APPEARANCE CARE 8

SPECIFICATIONS 9

SERVICE NETWORK 10

FOR SAFE DRIVING

1

72SM0-74E

72SM01000

FOR SAFE DRIVINGFloor Mats ............................................................................ 1-1Front Seats .......................................................................... 1-1Rear Seats ............................................................................ 1-3Seat Belts and Child Restraint Systems ........................... 1-8Child Restraint System for India......................................... 1-16Supplemental Restraint System (airbags) ........................ 1-22Exhaust Gas Warning ......................................................... 1-29

1-1

FOR SAFE DRIVING

72SM0-74E

Floor Mats (if equipped)

60MK020

To prevent the driver’s side floor mat fromsliding forward and possibly interfering withthe operation of the pedals, MARUTISUZUKI genuine floor mats are recom-mended.Whenever you put the driver’s side floormat back in the vehicle after it has beenremoved, be sure to hook the floor matgrommets to the fasteners and position thefloor mat properly in the footwell.

When you replace the floor mats in yourvehicle with a different type such as all-weather floor mats, we highly recommendusing MARUTI SUZUKI genuine floor matsfor proper fitting.

Front Seats

Seat AdjustmentEXAMPLE

WARNING

Failure to take the following precau-tions may result in the driver’s sidefloor mat interfering with the pedalsand causing a loss of vehicle controlor an accident.• Make sure that the floor mat grom-

mets are hooked to the fasteners.• Never stack additional floor mats

on top of the existing floor mat.

WARNING

Never attempt to adjust the driver’sseat or seatback while driving. Theseat or seatback could move unex-pectedly, causing loss of control.Make sure that the driver’s seat andseatback are properly adjustedbefore you start driving.

WARNING

To avoid excessive seat belt slack,which reduces the effectiveness ofthe seat belts as a safety device,make sure that the seats are adjustedbefore the seat belts are fastened.

WARNING

Do not place any object under thefront seat. If an object becomescaught under the front seat, the fol-lowing may occur.• The seat will not be latched.

1-2

FOR SAFE DRIVING

72SM0-74E

Adjusting Seat Position

73R0032

The adjustment lever for each front seat islocated under the front of the seat. Toadjust the seat position, pull up on theadjustment lever and slide the seat forwardor rearward. After adjustment, try to move the seat for-ward and rearward to ensure that it issecurely latched.

Adjusting Seat height (if equipped)

72R0132

If the driver’s seat is equipped with a seatheight adjuster lever on the outboard sideof the seat, raise or lower the seat by pull-ing up or down the adjuster lever.

Adjusting Seatbacks

72R0133

To adjust the seatback angle of front seats,pull up the lever on the outboard side ofthe seat, move the seatback to the desiredposition, and release the lever to lock theseatback in place.

WARNING

Do not leave cigarette lighters orspray cans on the floor. If a cigarettelighter or spray can is on the floor, itmay light accidentally when luggageis loaded or the seat is adjusted,causing a fire.

EXAMPLE

EXAMPLE WARNING

All seatbacks should always be in anupright position when driving, or seatbelt effectiveness may be reduced.Seat belts are designed to offer maxi-mum protection when seatbacks arein the upright position.

EXAMPLE

1-3

FOR SAFE DRIVING

72SM0-74E

Head Restraints

63J246

Head restraints are designed to helpreduce the risk of neck injuries in the caseof an accident. Adjust the head restraint tothe position which places the center of thehead restraint closest to the top of yourears. If this is not possible for very tall pas-sengers, adjust the head restraint as highas possible.

NOTE:It may be necessary to recline the seat-back to provide enough overhead clear-ance to remove the head restraint.

73R0035

To raise the front head restraint, pullupward on the restraint until it clicks. Tolower the restraint, push down on therestraint while holding in the lock lever inpushed condition as shown. If a headrestraint must be removed (for cleaning,replacement, etc.), push in the lock leverand pull the head restraint all the way out.

Rear Seats

Seat Adjustment

WARNING

• Never drive the vehicle with thehead restraints removed.

• Do not attempt to adjust the headrestraint while driving.

EXAMPLE

EXAMPLE

WARNING

To avoid excessive seat belt slack,which reduces the effectiveness ofthe seat belts as a safety device,make sure that the seats are adjustedbefore the seat belts are fastened.

WARNING

Do not place any object under 2ndrow seat. If an object gets caughtunder the seat, the seat will not belatched.

WARNING

Do not leave cigarette lighters orspray cans on the floor. If a cigarettelighter or spray can is on the floor, itmay light accidentally when luggageis loaded or the seat is adjusted,causing a fire.

1-4

FOR SAFE DRIVING

72SM0-74E

Adjusting Seat Position

For 2nd row seats

72SM01001

The adjustment levers for 2nd row seatsare located under the front of the seats. Toadjust the seat position, pull up on theadjustment lever and slide the seat forwardor rearward. After adjustment, try to move the seat for-ward and rearward to ensure that it issecurely latched.

Adjusting Seatbacks

For 2nd row seats

72SM01002

To adjust the seatback angle of 2nd rowseats, pull up the lever on the seat asshown in figure, move the seatback to thedesired position, and release the lever tolock the seatback in place.After adjustment, try to move the seat for-ward and rearward to ensure that it issecurely latched.

For 3rd row seats

73RS017

To adjust the seatback angle of 3rd rowseats, put one hand on the backrest andfully lift up the release lever in the upperside of the backrest. With the release lever in raised condition,pull down the backrest till the position littlebit more than desired angle. Then, remove hand from release lever andpush the backrest towards back to fix it inposition.

NOTICE

When the 3rd row seat is folded for-ward, adjust the 2nd row seat not toreach the 3rd row seat.

EXAMPLEWARNING

All seatbacks should always be in anupright position when driving, or seatbelt effectiveness may be reduced.Seat belts are designed to offer maxi-mum protection when seatbacks arein the upright position.

EXAMPLE

WARNING

Do not pull down the backrest morethan required, the seat belt cannotshow full effect.

EXAMPLEEXAMPLEEXAMPLE

1-5

FOR SAFE DRIVING

72SM0-74E

Walk-in Type Seats

For 2nd row seats

73R0038

NOTE:To enter to or exit from the 3rd row seat,insert the tongue plate of the buckle intothe part (1) before moving the 2nd rowseat.

72SM01003

The walk-in type seat can be moved toprovide easy entry to and exit from the 3rdrow seats. You can move a walk-in seat bylifting up the release lever and pushing theseatback forward.

NOTICE

Adjust the 3rd row seat after gettingdown from the seat. If the releaselever is pulled while being seated, thebackrest will suddenly collapse tomax angle.Pull the release lever fully. If the seatis made to collapse without the lockbeing released, movement of lockwill become heavy.

(1)

EXAMPLE

EXAMPLE

WARNING

• After using the walk-in function, besure to return the folded seat backto an upright position.

• Before returning a walk-in seat toits normal seating position, makesure that the feet of the passengerin the 3rd row seat are out of theway.

• After returning the seat to its nor-mal seating position, make sure itis securely latched.

NOTICE

• Release lever is meant for easyentry purpose only. Not to be usedfor adjusting seatback.

• When the 2nd row seat headrestraint reaches the front seat-back, slide the front seat forward.

1-6

FOR SAFE DRIVING

72SM0-74E

Head RestraintsHead restraints are designed to helpreduce the risk of neck injuries in the caseof an accident.

NOTE:It may be necessary to fold forward theseatback to provide enough overheadclearance to remove the head restraint.

Adjust the head restraint to the positionwhich places the center of the headrestraint closest to the top of your ears. Ifthis is not possible for very tall passengers,adjust the head restraint as high as possi-ble.

2nd row seats

72SM01004

3rd row seats

72SM01017

To raise the rear head restraint, pullupward on the restraint until it clicks. Tolower the restraint, push down on therestraint while holding in the lock lever. If ahead restraint must be removed (for clean-ing, replacement, etc.), push in the locklever and pull the head restraint all the wayout.

When installing a child restraint system,raise the head restraint to the most upperposition.

2nd row Armrest

72SM01016

Armrest is stowed at inboard side of theseats. Tilt it downward to use.

WARNING

• Never drive the vehicle with thehead restraints removed.

• Do not attempt to adjust the headrestraint while driving.

EXAMPLE

EXAMPLE

NOTICE

To prevent damage to the armrest, donot lean or sit on the armrest.

EXAMPLE

1-7

FOR SAFE DRIVING

72SM0-74E

Folding Rear Seats

3rd row seatsThe 3rd row seat of your vehicle can befolded forward to provide additional cargospace.

To fold the 3rd row seat forward:

1) Lower the head restraint fully.

73R0207

2) Stow the seat belt buckles of the rightand left seating position into the pocketof the seat cushion as shown in theillustration.

73R0007

3) Lift up the release lever on the top ofseat, and fold the seatback forward.

To return the seat to the normal position,follow the procedure below.

72SM01006

Raise the seatback until it locks into place.

When you raise the seat from back of it,pull the strap (1).

WARNING

If the seat belt is obstructed by anypart of the armrest when fastened, itcannot provide the intended protec-tion. After fastening the seat belt,always check that the armrest is notinterfering with the belt.

EXAMPLE

NOTICE

When the 3rd row seat head restraintreaches the 2nd row seatback, slidethe 2nd row seat forward.

NOTICE

When you are not using a seat belt,stow the seat belt buckles of the rightand left seating position into thepocket first. This helps prevent beingcaught by the seat and being dam-aged.

EXAMPLE

WARNING

If you need to carry cargo in the pas-senger compartment with the 3rd rowseatback folded forward, be sure tosecure the cargo or it may be thrownabout, causing injury. Never pilecargo higher than the seatback.

(1)

EXAMPLE

1-8

FOR SAFE DRIVING

72SM0-74E

After returning the seat, try moving theseatback to make sure they are securelylatched.

Seat Belts and Child Restraint Systems

65D231S 65D606

NOTICE

Do not allow items in the luggage boxto extend above the top of the lug-gage box. Otherwise, the luggagebox or cover may be damaged.

WARNING

• Wear Your Seat Belts at All Times.• An airbag supplements, or adds to,

the frontal collision protectionoffered by seat belts. The driverand all passengers must be prop-erly restrained by wearing seatbelts at all times, whether or not anairbag is mounted at their seatingposition, to minimize the risk ofsevere injury or death in the eventof a collision.

• Do not modify, remove, disassem-ble seat belts. Doing so may pre-vent them from functioningproperly and cause the risk ofsevere injury or death in the eventof a collision.

(Continued)

EXAMPLE

WARNING

• Never allow persons to ride in thecargo area of a vehicle. In the eventof an accident, there is a muchgreater risk of injury for personswho are not riding in a seat withtheir seat belt securely fastened.

• Seat belts should always beadjusted as follows:– the lap portion of the belt should

be worn low across the pelvis,not across the waist.

– the shoulder straps should beworn on the outside shoulderonly, and never under the arm.

– the shoulder straps should beaway from your face and neck,but not falling off your shoulder.

(Continued)

Above the pelvis

EXAMPLE

1-9

FOR SAFE DRIVING

72SM0-74E

65D201 65D199

WARNING

(Continued)• Seat belts should never be worn

with the straps twisted and shouldbe adjusted as tightly as is com-fortable to provide the protectionfor which they have been designed.A slack belt will provide less pro-tection than one which is snug.

• Check that seat belt latch plate(tongue) is inserted into the properbuckle especially in the rear seats.It is not possible to insert into thewrong buckles in the rear seats.

(Continued)

Across the pelvis

EXAMPLE

WARNING

(Continued)• Pregnant women should use seat

belts, although specific recommen-dations about driving should bemade by the woman’s medical advi-sor. Remember that the lap portionof the belt should be worn as lowas possible across the hips, asshown in the diagram.

• Do not wear your seat belt overhard or breakable objects in yourpockets or on your clothing. If anaccident occurs, objects such asglasses, pens, etc. under the seatbelt can cause injury.

(Continued)

as low as possible across the hips

EXAMPLE WARNING

(Continued)• Never use the same seat belt on

more than one occupant and neverattach a seat belt over an infant orchild being held on an occupant’slap. Such seat belt use could causeserious injury in the event of anaccident.

• Periodically inspect seat beltassemblies for excessive wear anddamage. Seat belts should bereplaced if webbing becomesfrayed, contaminated, or damagedin any way. It is essential to replacethe entire seat belt assembly after ithas been worn in a severe impact,even if damage to the assembly isnot obvious.

• Children age 12 and under shouldride properly restrained in the rearseat.

• Infants and small children shouldnever be transported unless theyare properly restrained. Restraintsystems for infants and small chil-dren can be purchased locally andshould be used. Make sure that thesystem you purchase meets appli-cable safety standards. Read andfollow all the directions providedby the manufacturer.

(Continued)

1-10

FOR SAFE DRIVING

72SM0-74E

Lap-Shoulder Belt

Emergency Locking Retractor (ELR)The seat belt has an emergency lockingretractor (ELR), which is designed to lockthe seat belt only during a sudden stop orimpact. It also may lock if you pull the beltacross your body very quickly. If this hap-pens, let the belt go back to unlock it, andthen pull the belt across your body moreslowly.

Safety reminder

60A038

60A040

To reduce the risk of sliding under the beltduring a collision, position the lap portionof the belt across your lap as low on yourhips as possible and adjust it to a snug fitby pulling the shoulder portion of the beltupward through the latch plate. The lengthof the diagonal shoulder strap adjusts itselfto allow freedom of movement.

WARNING

(Continued)• For children, if the shoulder belt

irritates the neck or face, move thechild closer to the center of thevehicle.

• Avoid contamination of seat beltwebbing by polishes, oils, chemi-cals, and particularly battery acid.Cleaning may safely be carried outusing mild soap and water.

• Do not insert any items such ascoins, clips, etc. into the seat beltbuckles, and be careful not to spillliquids into these parts. If foreignmaterials get into a seat beltbuckle, the seat belt may not workproperly.

• All seatbacks should always be inan upright position when driving,or seat belt effectiveness may bereduced. Seat belts are designed tooffer maximum protection whenseatbacks are in the upright posi-tion.

Sit up straight and fully back

Low on hips

EXAMPLE

Low on hips

EXAMPLE

1-11

FOR SAFE DRIVING

72SM0-74E

All Seat Belts

60A036

To fasten the seat belt, sit up straight andwell back in the seat, pull the latch plateattached to the seat belt across your bodyand press it straight into the buckle untilyou hear a “click”.

60A039

To unfasten the seat belt, push the buttonon the buckle and retract the belt slowlywhile attaching a hand to the belt or/andthe latch plate.

Driver’s seat belt reminder light / Front passenger’s seat belt reminder light

72SM01012

When the driver and/or front passengerdo(does) not fasten their seat belts, theseat belt reminder lights will come on orblink and a buzzer will sound to remind thedriver and/or passenger to fasten their seatbelts. For more details, refer to the expla-nation below.

NOTE:The driver’s seat belt reminder light / frontpassenger’s seat belt reminder light is forboth the driver and front passenger.

Driver’s seat belt reminderIf the driver’s seat belt remains unbuckledwhen the ignition mode is “ON”, thereminder works as follows: 1) The driver’s seat belt reminder light will

come on. 2) After the vehicle’s speed has reached

about 15 km/h, the driver’s seat beltreminder light will blink and a buzzerwill sound for about 95 seconds.

3) The reminder light will remain on untilthe driver’s seat belt is buckled.

If the driver has buckled his or her seat beltand later unbuckles the seat belt, thereminder system will be activated fromStep 1) or 2) according to the vehicle’sspeed. When the vehicle’s speed is lessthan 15 km/h, the reminder will start fromStep 1). When the vehicle’s speed is morethan 15 km/h, the reminder will start fromStep 2).The reminder will be automatically can-celed when the driver’s seat belt is buckledor the ignition mode is “OFF”.

EXAMPLE

EXAMPLE

EXAMPLE

1-12

FOR SAFE DRIVING

72SM0-74E

Front passenger’s seat belt reminderIf there is a person sitting in the front pas-senger seat and the front passenger seatbelt is unbuckled when the ignition mode is“ON”, the front passenger's seat beltreminder will activate.

69RH203

(2) The sensor of the front passenger’sseat belt reminder

The seat belt reminder sensor (2) detectswhether a person is sitting in the front seat.The sensor of the front passenger's seatbelt reminder is located in the seat cush-ion. The front passenger’s seat beltreminder works in the same manner as thedriver’s seat belt reminder.

(2)(2)

EXAMPLE

WARNING

It is absolutely essential that thedriver and passengers fasten theirseat belts at all times. Persons whoare not fastening seat belts have amuch greater risk of injury if an acci-dent occurs. Make a regular habit ofbuckling your seat belt before puttingthe key in the ignition or pressing theengine switch.

CAUTION

• Do not spill liquid or semi-solid onthe front passenger's seat. If youspill it on the front passenger'sseat, immediately wipe it dry with asoft cloth. Contact of liquid withsensor may impact the function ofseat belt reminder sensor.

• Do not place any sharp or heavyobject on passenger seat whichcan penetrate through seat uphol-stery and can cause damage tosensor.

NOTICE

• The sensor of the front passenger’sseat belt reminder is located in theseat cushion. If heavy or sharpobjects are put on the seat cush-ion, or a removal, disassembly andmodification of the passenger’sseat are performed, the sensor maynot work properly or can be dam-aged. Do not put heavy or sharpobjects on the seat cushion. Do notremove, disassemble and modifythe passenger’s seat.

• Depending on the variety of seatcover, operation of the sensor maybe adversely affected. MARUTISUZUKI highly recommends thatyou use MARUTI SUZUKI genuineseat cover exclusively for this vehi-cle.

• If you spill liquid such as liquid aro-matics, soft drinks or juice on thefront passenger’s seat cushion, thesensor of the front passenger’sseat belt reminder located in theseat cushion can be damaged.Immediately wipe it dry with a softcloth when spilled.

(Continued)

1-13

FOR SAFE DRIVING

72SM0-74E

NOTE:• If you put an object on the passenger’s

seat, the weight of the object will besensed by the sensor and the front pas-senger’s seat belt reminder light willcome on and then the interior buzzermay beep.

• If a child or a small sized person sits onthe front passenger’s seat or the cushionis put on the front passenger’s seat, theweight may not be sensed by the sensorand the interior buzzer may not beep.

• Maruti Suzuki recommends use ofMaruti Suzuki Genuine accessory of“Seat cover”.

Shoulder anchor height adjuster

64J198

Adjust the shoulder anchor height so thatthe shoulder belt rides on the center of theoutboard shoulder. To move upward, slidethe anchor up. To move downward, slidethe anchor down while pulling the lockknob out. After adjustment, check that theanchor is securely locked.

Seat Belt Catch Hole (for 2nd row seats)

73R0038

NOTE:To enter to or exit from the 3rd row seat,insert the tongue plate of the buckle intothe part (1) before moving the 2nd rowseat.

NOTICE

(Continued) • When sitting on the front passen-

ger’s seat, it is very important thatthe passenger sits upright, leaningagainst the seat backrest and cen-tered on the seat cushion in orderfor the seatbelt reminder system tofunction effectively. An occupantsitting improperly (slouches, turnssideways, sits forward or side-ways) may hamper the functioningof this system as it may not detectthe occupant.

WARNING

Check that the shoulder belt is posi-tioned on the center of the outsideshoulder. The belt should be awayfrom your face and neck, but not fall-ing off your shoulder. Misadjustmentof the belt could reduce the effective-ness of the seat belt in a collision.

EXAMPLE

NOTICE

When you move a seatback, makesure the tongue plate of the buckle isinserted in the seat belt catch hole sothe seat belts are not caught by theseatback, seat hinge, or seat latch.This helps prevent damage to the beltsystem.

(1)

EXAMPLE

1-14

FOR SAFE DRIVING

72SM0-74E

Seat Belt Inspection

65D209S

Periodically inspect the seat belts to makesure they work properly and are not dam-aged. Check the webbing, buckles, latchplates, retractors, anchorages, and guideloops. Replace any seat belts which do notwork properly or are damaged.

Child Restraint Systems

60G332S

The following types of child restraint sys-tem are available generally.Infant restraint - rear seat only

79J221

Child restraint

64L30820

Booster seat

79J223

WARNING

Inspect all seat belt assemblies afterany collision. Any seat belt assemblywhich was in use during a collision(other than a very minor one) shouldbe replaced, even if damage to theassembly is not obvious. Any seatbelt assembly which was not in useduring a collision must be replaced ifthe airbags and the seat belt preten-sioners activated. The airbags, thepretensioners and the load limitterwill only function once. In case theydid not activate, consult with a MarutiSuzuki authorised workshop.

EXAMPLE EXAMPLE

EXAMPLE

EXAMPLE

EXAMPLE

1-15

FOR SAFE DRIVING

72SM0-74E

MARUTI SUZUKI highly recommends thatyou use a child restraint system to restraininfants and small children. Many differenttypes of child restraint systems are avail-able; check that the restraint system youselect meets applicable safety standards.

All child restraint systems are designed tobe secured in vehicle seats either by seatbelts (the lap portion of lap-shoulder belts)or by special rigid lower anchor bars builtinto the seat.

NOTE:Observe any statutory regulation aboutchild restraints.

61M0241

65D608D

65D609S

EXAMPLE

WARNING

Do not install a child restraint systemon the front passenger's seat since achild restraint system cannot beinstalled appropriately.

WARNING

If you install a child restraint systemin the 2nd row seat, slide the seatinstalled the child restraint system asfar back as possible. So that, thechild’s feet do not contact the frontseatback. These will help avoid injuryto the child in the event of an acci-dent.

EXAMPLE

WARNING

Children could be endangered in acollision if their child restraint sys-tems are not properly secured in thevehicle. When installing a childrestraint system, follow the instruc-tions below. secure the child in therestraint system according to themanufacturer’s instructions.

EXAMPLE

1-16

FOR SAFE DRIVING

72SM0-74E

Child Restraint System for IndiaChild Restraint

The suitability of each passenger’s seat position for carriage of children and fitting of child restraint system is shown in the table below.Whenever you carry children up to 12 years of age, properly use the child restraints which conform to AIS 072, the standard for childrestraints, referring to the table.

Key of letters to be inserted in the above table:U =Suitable for ‘universal’ category restraints approved for use in this mass groupX =Seat position not suitable for children in this mass groupN.A = Seat position not available for children in this mass group. NOTE: ‘universal’ is the category in the AIS 072. : ‘Outboard’ indicates window side seat.

MASS GROUP

Seating position (or other site)

Front Passenger

Rear Outboard

Rear Centre

Intermediate Outboard

Intermediate Centre

Group 0Up to 10 kg X X N.A U N.A

Group 0+Up to 13 kg X X N.A U N.A

Group I9 to 18 kg X X N.A U N.A

Group II15 to 25 kg X X N.A U N.A

Group III22 to 36 kg X X N.A U N.A

1-17

FOR SAFE DRIVING

72SM0-74E

Installation with lap-shoulder seat belts

NOTE:Stow the removed head restraint in the lug-gage compartment so it will not causeinconvenience to the occupants.

ELR type belt

80JC021

Install your child restraint system accord-ing to the instructions provided by the childrestraint system manufacturer.

Check that the seat belt is securelylatched.Move the child restraint system in all direc-tions to check that it is securely installed.When you put your child in the childrestraint system, appropriately slide thefront seat forward not to touch a part ofyour child’s body.

Installation with ISOFIX type anchorages

72SM01009

Your vehicle is equipped with the loweranchorages in the 2nd row seat for secur-ing an ISOFIX type of child restraints withthe connecting bars. The lower anchor-ages are located where the rear of the seatcushion meets the bottom of the seatback.

Install the ISOFIX type child restraint sys-tem according to the instructions providedby the child restraint system manufacturer.After installation, try moving the childrestraint system in all directions especiallyforward to check that connecting bars aresecurely latched to the anchorages.

CAUTION

If your vehicle is equipped with therear head restraint, adjust the heightof the head restraint or remove it forfitting the child restraint, as neces-sary. However, if a booster cushionnot equipped with the seatback is fit-ted, the seat head restraint shouldnot be removed. If the head restraintis removed for fitting the childrestraint, you need to install it againafter removing the child restraint.If the child restraint is fitted improp-erly, a child sitting in it could beinjured in a collision.

EXAMPLEEXAMPLE

1-18

FOR SAFE DRIVING

72SM0-74E

72SM01007

Your vehicle is equipped with the top tetheranchorages. Use the top tether strap of thechild restraint according to the instructionsprovided by the child restraint system man-ufacturer.

Here is a general instruction:


78F114

1) Place the child restraint in the 2nd rowseat, inserting the connecting bars tothe anchorages between the seat cush-ion and the seatback.

68LM268

EXAMPLECAUTION

If your vehicle is equipped with therear head restraint, adjust the heightof the rear head restraint or remove itfor fitting the child restraint, as nec-essary. However, if a booster cushionnot equipped with the seatback is fit-ted, the 2nd row seat head restraintshould not be removed. If the rearhead restraint is removed for fittingthe child restraint, you need to installit again after removing the childrestraint.If the child restraint is fitted improp-erly, a child sitting in it could beinjured in a collision.

EXAMPLE

EXAMPLE

1-19

FOR SAFE DRIVING

72SM0-74E

2) Use your hands to carefully align theconnecting bar tips with the anchor-ages. Take care not to pinch your fin-gers.

54G184

3) Push the child restraint toward the anchor-ages so that the connecting bar tips arepartially hooked to the anchorages. Useyour hands to confirm the position.

54G185

4) Grasp the front of the child restraint andpush the child restraint forcefully tolatch the connecting bars. Check thatthey are securely latched by trying tomove the child restraint system in alldirections, especially forward.

5) Attach the top tether strap referring to“Installation of child restraint with toptether” section.When you put your child in the childrestraint system, appropriately slide thefront seat forward not to touch a part ofyour child’s body.

Installation of child restraint with top tether


EXAMPLE

NOTICE

When installing a child restraint sys-tem to the 2nd row seat, slide theseat installed the child restraint sys-tem as far back as possible.

EXAMPLE

CAUTION

If your vehicle is equipped with therear head restraint, adjust the heightof the rear head restraint or remove itfor fitting the child restraint, as nec-essary. However, if a booster cushionnot equipped with the seatback is fit-ted, the 2nd row seat head restraintshould not be removed. If the rearhead restraint is removed for fittingthe child restraint, you need to installit again after removing the childrestraint.If the child restraint is fitted improp-erly, a child sitting in it could beinjured in a collision.

1-20

FOR SAFE DRIVING

72SM0-74E

72SM01014

Some child restraint systems require theuse of a top tether strap. Top tether anchor-age brackets (2) are provided in your vehi-cle at the locations shown in the illustration.Lift the flap (1) to access the brackets.The number of the top tether anchoragebrackets provided in your vehicle dependson the vehicle specification. Install the childrestraint system as follows:

1) Secure the child restraint on the 2ndrow seat using the procedure describedabove for securing a restraint systemthat does not require a top tether strap.

2) Hook the top tether strap to the toptether anchorage bracket and tightenthe top tether strap according to theinstructions provided by the childrestraint system manufacturer. Attachthe top tether strap to the correspond-ing top tether anchorage bracketlocated directly behind the childrestraint.

72SM01015

3) When routing the top tether strap, passthe top tether strap as shown in theillustration. (Refer to “Head restraints”section for details on how to adjust theheight of head restraint or remove it.)

4) Check that cargo does not interferewith routing of the top tether strap.

NOTE:Maruti Suzuki recommends use of MarutiSuzuki Genuine accessory of “Child seat,ISOFIX”.

Seat belt pretensioner system

63J269

(1)

(2)

Front

EXAMPLE

EXAMPLE

NOTICE

When installing a child restraint sys-tem to the 2nd row seat, adjust thefront seat position so that the frontseat does not interfere with the childrestraint system.

and/or

Label

EXAMPLE

1-21

FOR SAFE DRIVING

72SM0-74E

To determine if your vehicle is equippedwith a seat belt pretensioner system at thefront seating positions, check the label onthe seat belt at the bottom part. If the let-ters “p” and/or “PRE” appear as illustrated,your vehicle is equipped with the seat beltpretensioner system. You can use the pre-tensioner seat belts in the same manner asordinary seat belts.Read this section and “Supplementalrestraint system (airbags)” section to learnmore about the pretensioner system.

The seat belt pretensioner system workswith the supplemental restraint system (airbags). The collision sensors and the elec-tronic controller of the airbag system alsocontrol the seat belt pretensioners. Thepretensioners are triggered only whenthere is a frontal collision severe enough totrigger the airbags and the seat belts arefastened. For precautions and generalinformation including servicing the preten-sioner system, refer to “Supplementalrestraint system (airbags)” section in addi-tion to this “Seat belt pretensioner system”section, and follow all those precautions.

The pretensioner is located in each frontseat belt retractor. The pretensioner tight-ens the seat belt so the belt fits the occu-pant’s body more snugly in the event of afrontal collision. The retractors will remainlocked after the pretensioners are acti-vated. Upon activation, some noise willoccur and some smoke may be released.These conditions are not harmful and donot indicate a fire in the vehicle.

The driver and all passengers must beproperly restrained by fastening seat beltsat all times, whether or not a pretensioneris equipped at their seating position, tominimize the risk of severe injury or deathin the event of a collision.

Sit fully back in the seat; sit up straight; donot lean forward or sideways. Adjust thebelt so the lap portion of the belt is wornlow across the pelvis, not across the waist.Please refer to “Seat adjustment” sectionand the instructions and precautions aboutthe seat belts in this “Seat belts and childrestraint systems” section for details onproper seat and seat belt adjustments.

Please note that the pretensioners alongwith the airbags will activate in severe fron-tal collisions. They are not designed toactivate in rear impacts, roll-overs, orminor frontal collisions. The pretensionerscan be activated only once. If the preten-sioners are activated (that is, if the airbagsare activated), have the pretensioner sys-

tem serviced by a Maruti Suzuki autho-rised workshop as soon as possible.

If AIRBAG light on the instrument clusterdoes not blink or come on briefly when theignition is pushed to “ON” mode, stays onfor more than 10 seconds, or comes onwhile driving, the pretensioner system orthe airbag system may not work properly.Have both systems inspected by a MarutiSuzuki authorised workshop as soon aspossible.

Service on or around the pretensioner sys-tem components or wiring must be per-formed only by a Maruti Suzuki authorisedworkshop who is specially trained.Improper service could result in unin-tended activation of pretensioners or couldrender the pretensioner inoperative. Eitherof these two conditions may result in per-sonal injury.

To prevent damage or unintended activa-tion of the pretensioners, check that thelead-acid battery is disconnected and theignition mode has been LOCK (OFF) for atleast 90 seconds before performing anyelectrical service work on your MARUTISUZUKI vehicle.

Do not touch pretensioner system compo-nents or wiring. The wires are wrappedwith yellow tape or yellow tubing, and thecouplers are yellow. When scrapping yourMARUTI SUZUKI vehicle, ask a MarutiSuzuki authorised workshop, body repairshop, or scrap yard for assistance.

WARNING

This section describes your MARUTISUZUKI vehicle’s seat belt preten-sioner system. Read and follow allthese instructions carefully to mini-mize your risk of severe injury ordeath.

1-22

FOR SAFE DRIVING

72SM0-74E

Supplemental Restraint System (airbags)

Your vehicle is equipped with a Supple-mental Restraint System consisting of thefollowing components in addition to a lap-shoulder belt at each front seating position.

1. Driver’s front airbag module 2. Front passenger’s front airbag mod-

ule3. Seat belt pretensioners4. Airbag controller5. Forward collision sensor

WARNING

This section of the owner’s manualdescribes the protection provided byyour Maruti Suzuki’s supplementalrestraint system (airbags). Please read and follow all theseinstructions carefully to minimizeyour risk of severe injury or death inthe event of a collision.

73R0044

3

5

1

2

3

33

55

11

22

33

EXAMPLE

1-23

FOR SAFE DRIVING

72SM0-74E

AIRBAG light

63J030

If the “AIRBAG” light on the instrumentcluster does not blink or come on when theignition mode is first changed to “ON”, orthe “AIRBAG” light stays on, or comes onwhile driving, the airbag system (or theseat belt pretensioner system) may notwork properly. Have the airbag systeminspected by a Maruti Suzuki authorisedworkshop as soon as possible.

Front Airbags

63J259

Front airbag is designed to inflate insevere frontal collisions when the ignitionmode is “ON”.

Front airbag is not designed to inflate inrear impacts, side impacts, rollovers orminor frontal collisions, since they wouldoffer no protection in those types of acci-dents. Remember, since an airbag deploysonly one time during an accident, seatbelts are needed to restrain occupantsfrom further movements during the acci-dent.

Therefore, an airbag is not a substitute forseat belts. To maximize your protection,always fasten your seat belts. Be awarethat no system can prevent all possibleinjuries that may occur in an accident.

Driver's front airbag

73R0009

Front passenger’s front airbag

72R0143

WARNING

An airbag supplements or adds to thecollision protection offered by seatbelts. The driver and all passengersmust be properly restrained by fas-tening seat belts at all times, whetheror not an airbag is mounted at theirseating position, to minimize the riskof severe injury or death in the eventof a collision.

EXAMPLE EXAMPLE

EXAMPLE

1-24

FOR SAFE DRIVING

72SM0-74E

The driver’s front airbag is located behindthe center pad of the steering wheel andthe front passenger’s front airbag islocated behind the passenger’s side of thedashboard. The words “SRS AIRBAG” aremolded into the airbag covers to identifythe location of the airbags.

61M0241

Refer to “Seat belts and child restraint sys-tems” section for details on securing yourchild.

Conditions of front airbags deployment(inflation)

80J097

• Frontal collision with a fixed wall thatdoes not move or deform at more thanabout 25 km/h

80J098E

• Strong impact equivalent to frontal colli-sion such as above at left and rightangles of about 30 degrees (1) or lessfrom the front of your vehicle

Conditions of front airbags may inflateReceiving a strong impact to the lowerbody of your vehicle, the front airbags mayinflate.

80J099

• Hitting a curb or medial strip

WARNING

Do not install a child restraint systemon the front passenger's seat since achild restraint system cannot beinstalled appropriately.

EXAMPLE

WARNING

If the airbag stored place is damagedor cracked, the airbag system maynot work properly, which could resultin serious injury in the event of a col-lision. Have your vehicle inspectedby a Maruti Suzuki authorised work-shop.

EXAMPLE

(1)

(1)

(1)

(1)

EXAMPLE

EXAMPLE

1-25

FOR SAFE DRIVING

72SM0-74E

80J100E

• Falling into a deep hole or ditch

80J101

• Landing hard or falling

Front airbags may not inflateThe front airbags may not inflate when astrong impact has not occurred since thecollision object was easy to be deformedor moved, or the collided portion of yourvehicle was easy to be deformed.Also, front airbags may not inflate in manycases when the collision angle is greaterthan about 30 degrees at left and rightangles from the front of your vehicle.

80J102

• Frontal collision to a stopped vehicle atless than about 50 km/h

80J103

• Collision that the front of your vehiclegoes under the bed of a truck etc.

80J104

• Collision with a utility pole or stumpage

80J105E

• Collision with a fixed wall or guardrail atleft and right angles of greater thanabout 30 degrees (1) from the front ofyour vehicle

EXAMPLE

EXAMPLE

EXAMPLE

EXAMPLE

EXAMPLE

(1)(1)

EXAMPLE

1-26

FOR SAFE DRIVING

72SM0-74E

80J106

• Frontal collision with a fixed wall thatdoes not move or deform at less thanabout 25 km/h

Front airbags do not inflateFront airbags do not inflate in rear impacts,side impacts or rollovers, etc. However,these might inflate in a strong impact.

80J120

• Impact from the rear

80J119

• Impact from the side

80J110

• Vehicle rollover

Airbag symbol meaning

72M00150

You may find this label on the sun visor.

EXAMPLE

EXAMPLE

EXAMPLE

EXAMPLE

WARNING

NEVER use a rearward facing childrestraint on a seat protected by anACTIVE AIRBAG in front of it, DEATHor SERIOUS INJURY to the CHILDcan occur.

WARNING

If the AIRBAG light in the instrumentcluster ever comes on and stays on,it means that something may bewrong with the airbag system. If thisever happens, have the vehicle ser-viced immediately, because the air-bags may not offer the protection forwhich they were designed.

EXAMPLE

1-27

FOR SAFE DRIVING

72SM0-74E

How the System WorksIn a frontal collision, the collision sensorswill detect rapid deceleration, and if thecontroller judges that the deceleration rep-resents a severe frontal collision, the con-troller will trigger the inflators. The inflatorsinflate the appropriate airbags with nitro-gen or argon gas. The inflated airbags pro-vide a cushion for your head and upperbody. The airbag inflates and deflates soquickly that you may not even realize that ithas activated. The airbag will neither hin-der your view nor make it harder to exit thevehicle.

Airbags must inflate quickly and forcefullyin order to reduce the chance of serious orfatal injuries. However, an unavoidableconsequence of the quick inflation is thatthe airbag may irritate bare skin, such asthe facial area against a front airbag. Washoff any residue as soon as possible to pre-vent skin irritation. Also, upon inflation, aloud noise will occur and some powderand smoke will be released. These condi-tions are not harmful and do not indicate afire in the vehicle. Be aware, however, thatsome airbag components may be hot for awhile after inflation.

A seat belt helps keep you in the properposition for maximum protection when anairbag inflates. Adjust your seat as farback as possible while still maintainingcontrol of the vehicle. Sit fully back in yourseat; sit up straight; do not lean over thesteering wheel or dashboard. Please referto the “Seat Adjustment” section and the“Seat Belts and Child Restraint Systems”in this section for details on proper seatand seat belt adjustments.

65D610S

EXAMPLE

WARNING

• The driver should not lean over thesteering wheel. The front passen-ger should not rest his or her bodyagainst the dashboard, or other-wise get too close to the dash-board. In these situations, the out-of-position occupant would be tooclose to an inflating airbag, andmay suffer severe injury.

• Do not attach any objects to, orplace any objects over, the steeringwheel or dashboard. Do not placeany objects between the airbag andthe driver or front passenger.These objects may interfere withairbag operation or may be pro-pelled by the airbag in the event ofa collision. Also, these objects maymove when you start moving vehi-cle or while vehicle is moving, theymay interfere with driver’s view orsafe driving. In each conditionsmay cause severe injury.

• Do not strike or apply significantlevels of impact to the air bag com-ponent areas. It can cause the airbags to malfunction.

1-28

FOR SAFE DRIVING

72SM0-74E

Note that even though your vehicle may bemoderately damaged in a collision, the col-lision may not have been severe enough totrigger the airbags to inflate. If your vehiclesustains any front-end or side damage,have the airbag system inspected by aMaruti Suzuki authorised workshop toensure it is in proper working order.

Your vehicle is equipped with a diagnosticmodule which records information aboutthe airbag system if the airbags deploy in acollision. The module records informationabout overall system status, which sensorsactivated the deployment, and for a certain

vehicle only, whether the driver’s seat beltwas in use.

Servicing the airbag systemIf the airbags inflate, have the airbags andrelated components replaced by a MarutiSuzuki authorised workshop as soon aspossible.

If your vehicle ever gets in deep water andthe driver’s floor is submerged, the airbagcontroller could be damaged. If it does,have the airbag system inspected by theMaruti Suzuki authorised workshop assoon as possible.

Special procedures are required for servic-ing or replacing an airbag. For that reason,only a Maruti Suzuki authorised workshopshould be allowed to service or replaceyour airbags. Please remind anyone whoservices your MARUTI SUZUKI that it hasairbags.

Service on or around airbag componentsor wiring must be performed only by aMaruti Suzuki authorised workshop.Improper service could result in unin-tended airbag deployment or could renderthe airbag inoperative. Either of these twoconditions may result in severe injury.

To prevent damage or unintended inflationof the airbag system, be sure the lead-acidbattery is disconnected and the ignitionmode has been in the LOCK (OFF) posi-tion for at least 90 seconds before per-forming any electrical service work on your

MARUTI SUZUKI. Do not touch airbagsystem components or wires. The wiresare wrapped with yellow tape or yellow tub-ing, and the couplers are yellow for easyidentification.

Scrapping a vehicle that has an uninflatedairbag can be hazardous. Ask your dealer,body repair shop or scrap yard for helpwith disposal.

WARNING

• Do not modify the system in anyway including replacing the steer-ing wheel, placing stickers on thesteering wheel pad, painting thesteering wheel, or covering thesteering wheel with a cover.

• Do not place stickers on or paintthe instrument panel. Do not installand set up accessories, air fresh-eners, ETC readers, or portablenavigation systems. Do not standumbrellas or similar in front of air-bags.

• Excluding Maruti Suzuki genuineparts, do not attach accessories tothe front windshield or the rearviewmirror.

1-29

FOR SAFE DRIVING

72SM0-74E

Exhaust Gas Warning

72SM01011

WARNING

Avoid breathing exhaust gases.Exhaust gases contain carbon mon-oxide, a potentially lethal gas that iscolorless and odorless. Since carbonmonoxide is difficult to detect byitself, be sure to take the followingprecautions to help prevent carbonmonoxide from entering your vehicle.• Do not leave the engine running in

garages or other confined areas.(Continued)

EXAMPLE

WARNING

(Continued)• Do not park with the engine run-

ning for a long period of time, evenin an open area. If it is necessary tosit for a short time in a parked vehi-cle with the engine running, makesure the air intake selector is set to“FRESH AIR” and the blower is athigh speed.

• Avoid operating the vehicle withthe tailgate or trunk open. If it isnecessary to operate the vehiclewith the tailgate or trunk open,make sure all windows are closed,and the blower is at high speedwith the air intake selector set to“FRESH AIR”.

• To allow proper operation of yourvehicle’s ventilation system, keepthe air inlet grille in front of thewindshield clear of snow, leaves orother obstructions at all times.

• Keep the exhaust tailpipe area clearof snow and other material to helpreduce the buildup of exhaustgases under the vehicle. This isparticularly important when parkedin blizzard conditions.

• Have the exhaust system inspectedperiodically for damage and leaks.Any damage or leaks should berepaired immediately.

BEFORE DRIVING

2

72SM0-74E

60G404

Keys ......................................................................................2-1Door Locks ...........................................................................2-2Keyless push start system remote controller....................2-5Security System ...................................................................2-12Theft deterrent light .............................................................2-14Windows ...............................................................................2-14Mirrors ..................................................................................2-17Instrument Cluster ...............................................................2-21Speedometer ........................................................................2-22

BEFORE DRIVINGTachometer .......................................................................... 2-22Fuel gauge ........................................................................... 2-22Temperature Gauge ............................................................. 2-23Brightness Control .............................................................. 2-23Information Display ............................................................. 2-24Warning and Indicator Lights ............................................ 2-47Lighting Control Lever ........................................................ 2-54Front Fog Light Switch ....................................................... 2-59Headlight Leveling Switch .................................................. 2-59Turn Signal Control Lever .................................................. 2-60Hazard Warning Switch ...................................................... 2-61Windshield Wiper and Washer Lever ................................ 2-61Tilt Steering Lock Lever ..................................................... 2-63Horn ...................................................................................... 2-64Heated Rear Window Switch .............................................. 2-64Vehicle Loading ................................................................... 2-65Trailer Towing your vehicle ................................................ 2-65

2-1

BEFORE DRIVING

72SM0-74E

Keys

72SM02004

Your vehicle comes with a pair of identicalkeys. Keep the spare key in a safe place.One key can open all of the locks on thevehicle.

The key identification number is stampedon a metal tag provided with the keys or onthe keys. Keep the tag in a safe place. Ifyou lose your keys, you will need this num-ber to have new keys made. Write thenumber below for your future reference.

Immobilizer System This system is designed to help preventvehicle theft by electronically disabling theengine starting system.The engine can be started only with yourvehicle’s original keyless push start systemremote controller, which has an electronicidentification code programmed in it. Theremote controller communicates the identi-fication code to the vehicle when the igni-tion is pushed to “ON” mode. If you need tomake spare keys or remote controllers,see a Maruti Suzuki authorised workshop.The vehicle must be programmed with thecorrect identification code for the spare. Akey made by an ordinary locksmith will notwork.

80JM122

If the immobilizer/keyless push start sys-tem warning light blinks when the ignitionmode is “ON”, the engine will not start.

If this light blinks, change the ignition modeto “LOCK” (OFF), and then change it backto “ON”. Also refer to “If the master warn-ing indicator light blinks and the enginecannot be started” in “Starting engine” in“OPERATING YOUR VEHICLE” section.

If the light still blinks after the ignition modeis changed back to “ON”, there may besomething wrong with your key or with theimmobilizer system. Ask a Maruti Suzukiauthorised workshop to have the systeminspected.

The immobilizer/keyless push start systemwarning light may also blink if the remotecontroller is not in the vehicle when youclose the door and attempt to start theengine.

NOTE:• If you lose your immobilizer remote con-

troller, ask a Maruti Suzuki authorisedworkshop as soon as possible to deacti-vate the lost one, and to make a newremote controller.

• If you own other vehicles with immobi-lizer keys, keep those keys away fromthe engine switch when using yourMARUTI SUZUKI vehicle. Otherwise, orthe engine may not be started becausethey may interfere with your MARUTISUZUKI vehicle’s immobilizer system.

• If you attach any metal objects to theremote controller, it may not start theengine.

KEY NUMBER:

EXAMPLE

2-2

BEFORE DRIVING

72SM0-74E

This immobilizer system is maintenance-free.

Door Locks

Side Door Locks

60B008

(1) UNLOCK(2) LOCK(3) Front(4) Rear

To lock a front door from outside the vehi-cle:

• Insert the key and turn the top of the keytoward the front of the vehicle, or

• Turn the lock knob forward, then pull andhold the door handle as you close thedoor.

To unlock a front door from outside thevehicle, insert the key and turn the top ofthe key toward the rear of the vehicle.

73R0001

(1) LOCK(2) UNLOCK

To lock a door from inside the vehicle, turnthe lock knob forward. Turn the lock knobrearward to unlock the door.

To lock a rear door from outside the vehi-cle, turn the lock knob forward and closethe door. You do not need to pull and holdthe door handle as you close the door.

NOTE:Be sure to hold the door handle when youclose a locked front door, or the door willnot remain locked.

NOTICE

The remote controller are sensitiveelectronic instruments.To avoid damaging them:• Do not expose them to impacts,

moisture or high temperature suchas on the dashboard under directsunlight.

• Keep them away from magneticobjects.

NOTICE

Do not modify or remove the immobi-lizer system.If modified or removed, the systemcannot be properly operated.

(2)

(1)

(3)

(4)

EXAMPLE

(2)(1)EXAMPLE

2-3

BEFORE DRIVING

72SM0-74E

Central Door Locking System

54G294

(1) UNLOCK(2) LOCK(3) Front(4) Rear

You can lock and unlock all doors (includ-ing the tailgate) simultaneously by usingthe key in the driver’s door lock.

To lock all doors simultaneously, insert the keyin the driver’s door lock and turn the top of thekey toward the front of the vehicle once.

To unlock all doors simultaneously, insert thekey in the driver’s door lock and turn the top ofthe key toward the rear of the vehicle twice.

To unlock the driver’s door only, insert the keyin that door lock and turn the top of the keytoward the rear of the vehicle once.

73R0002

(1) LOCK(2) UNLOCK

You can also lock or unlock all doors bydepressing the front or rear of the switch,respectively.

NOTE:• You can also lock or unlock all doors by

operating the remote controller. Refer to“Keyless push start system remote con-troller” in this section.

• You can also lock or unlock all doors bypushing the request switch. Refer to“Keyless push start system remote con-troller” in this section.

NOTE:• All doors are automatically unlocked

when you change the ignition mode toLOCK (OFF).

• All doors are automatically locked forsafety when the vehicle speed reaches15 km/h.

• You can change the automatic locking orunlocking function mentioned above viathe setting mode of the information dis-play. For details on how to use the infor-mation display, refer to “Informationdisplay” in this section.

(1)

(2)

(3)

(4)

EXAMPLE(2)

(1)EXAMPLE

2-4

BEFORE DRIVING

72SM0-74E

Child-Proof Locks (rear door)

73R0003

(1) LOCK(2) UNLOCK

Each of the rear doors is equipped with achild-proof lock which can be used to helpprevent unwanted opening of the doorfrom inside the vehicle. When the locklever is in LOCK position (1), the rear doorcan only be opened from outside. Whenthe lock lever is in UNLOCK position (2),the rear door can be opened from inside oroutside.

Tailgate

72SM02001

(1) Tailgate handle

You can lock and unlock the tailgate byusing the key in the driver’s door lock.

To open the tailgate, pull up the tailgatehandle (1) and lift the tailgate.If you cannot unlock the tailgate by usingthe key in the driver’s door lock due to a

discharged lead-acid battery or malfunc-tion, follow the procedure below to unlatchthe tailgate from inside the vehicle.1) Fold the rear seat forward for easier

access. Refer to “Folding rear seats”section for details on how to fold therear seat forward.

73R0020

2) Open the cover (2) in the lock mecha-nism of the tailgate.

NOTE:Be careful not to lose the cover (2)because it is small and detachable.

WARNING

Place the child-proof lock in LOCKposition whenever children areseated in the rear.

(2)

(1)

EXAMPLE WARNING

Always make sure that the tailgate isclosed and latched securely. Com-pletely closing the tailgate helps pre-vent occupants from being thrownfrom the vehicle in the event of anaccident. Completely closing it alsohelps keep exhaust gases from enter-ing the vehicle.

(1)

EXAMPLE(2)(2)(2)

EXAMPLE

2-5

BEFORE DRIVING

72SM0-74E

73R0021

3) Move the lever (3) in arrow direction byusing a flat-bladed screwdriver tounlock the tailgate.

4) Push open the tailgate from inside. Thetailgate will be latched again by simplyclosing the tailgate.

If the tailgate cannot be unlatched by push-ing the unlatch switch (1), have the vehicleinspected by a Maruti Suzuki authorisedworkshop.

Keyless push start system remote controller

72SM02002

Your vehicle is equipped with a keylesspush start system. The remote controller ofthis system has keyless entry function andkeyless push start function. For details,refer to the following explanations.

CAUTION

Check that there is no one near thetailgate when pushing open the tail-gate from inside the vehicle.

(3)(3)(3)

(3)(3)(3)EXAMPLE

EXAMPLE

WARNING

Radio waves from the keyless pushstart system antenna(s) may interferewith operation of electrical medicalequipment such as pacemakers. Fail-ure to take the precautions listedbelow can increase the risk of severeinjury or death due to radio waveinterference.• Anyone who uses electrical medi-

cal equipment such as a pace-maker should consult the medicalequipment supplier or their medicaladvisor about whether radio wavesfrom the antenna(s) can interferewith the medical equipment.

• If radio wave interference is a con-cern, have the function of theantenna(s) disabled by a MarutiSuzuki authorised workshop.

2-6

BEFORE DRIVING

72SM0-74E

Keyless Push Start System Remote ControllerThe remote controller enables the follow-ing operations:

• You can lock or unlock the doors bypushing LOCK/UNLOCK buttons on theremote controller. Refer to the explana-tion in this section.

• You can lock or unlock the doors bypushing the request switch in the frontoutside door handles. For details, referto the explanation in this section.

• You can start the engine without usingan ignition key. For details, refer to“Engine Switch” in “OPERATING YOURVEHICLE” section.

52RM20060

(1) LOCK button(2) UNLOCK button

You can lock or unlock all doors (includingthe tailgate) simultaneously by operatingthe remote controller near the vehicle.

Central door locking system• To lock all doors, push LOCK button (1)

once.• To unlock only the driver’s door, push

UNLOCK button (2) once.• To unlock other doors, push UNLOCK

button (2) once again.

NOTE:You can switch the function that unlocks alldoors from twice operations to once opera-tion, and vice versa, via the setting modeof the information display. For details onhow to use the information display, refer to“Information Display” in this section.

The turn signal lights will flash once andthe siren will sound once when the doorsare locked.

When the doors are unlocked:

• The turn signal lights will flash twice andthe siren will sound twice.

• If the interior light switch is in the“DOOR” position, the interior light willturn on for 15 seconds and then fadeout. If you press the engine switch duringthis time, the light will start to fade outimmediately.

Be sure the doors are locked after youoperate the LOCK button (1).

NOTE:If no door is opened within about 30 sec-onds after the UNLOCK button (2) is oper-ated, the doors will automatically lockagain.

NOTE:• If the security system was triggered due

to an unauthorized entry into the vehicleand then you unlock the doors using theremote controller, the siren will sound 4times to remind you. If this happens,check whether your vehicle has beenbroken into while you were away from it.

• Once you push both of the LOCK button(1) and UNLOCK button (2), then youpush one of the buttons within 5 sec-onds, the siren will not sound.

• You can set whether the siren soundswhen locking or unlocking the doors viathe setting mode of the information dis-play. For details on how to use the infor-mation display, refer to “InformationDisplay” in this section.

NOTE:• The maximum operating distance of the

remote controller is about 5 m (16 ft.),but this can vary depending on the sur-roundings, especially near other trans-mitting devices such as radio towers orCB (Citizen’s Band) radios.

(1)

(2)

(1)

(2)

EXAMPLE

2-7

BEFORE DRIVING

72SM0-74E

• The door locks cannot be operated withthe remote controller if the ignition modeis other than the “LOCK” (OFF).

• When any door is open, if you push theLOCK button on the remote controller,the siren will sound and doors cannot belocked.

• If you lose one of the remote controllers,ask a Maruti Suzuki authorised work-shop as soon as possible for a replace-ment. Be sure to have your dealerprogram the new remote controller codein your vehicle’s memory so that the oldcode is erased.

Car locator alarm functionThis function is to get the attention of oth-ers. Push both of the LOCK button (1) andUNLOCK button (2) for more than 3 sec-onds. The turn signal lights will blink forabout 27.5 seconds. Also, the siren willsound for about 27.5 seconds at the sametime. To cancel the car locator alarm, pressany button (LOCK or UNLOCK). You canalso cancel the car locator alarm in any ofthe following operations.

• Press the engine switch to change theignition mode to ON (if car is unlocked).

• Bring the remote controller with you andpress the request switch (if car islocked).

NOTE:The car locator alarm function will not acti-vate when the ignition mode is ACC or ON.

Keyless unlocking/locking using therequest switches

72SM02003

When the remote controller is within theoperating range described in this section,you can lock or unlock the doors (includingthe tailgate) by pushing the request switch(1) on the driver’s door handle, front pas-senger’s door handle or tailgate (2).

To lock all doors when all doors areunlocked:

• To lock all doors, push one of therequest switches once.

The turn signal lights will flash once andthe siren will sound once when the doorsare locked.

To unlock a door or all doors:

• Push one of the request switches onceto unlock the respective door or the tail-gate.

• Push one of the request switches twiceto unlock all doors.

NOTE:You can switch the function that unlocks alldoors from twice operations to once opera-tion, and vice versa, via the setting modeof the information display. For details onhow to use the information display, refer to“Information Display” in this section.

When the doors are unlocked:

• The turn signal lights will flash twice andthe siren will sound twice.

• If the interior dome light switch is inDOOR position, the interior dome lightwill turn on for 15 seconds and then fadeout. If you press the engine switchduring this time period, the light will startto fade out immediately.

Be sure the doors are locked after youoperate the request switch to lock thedoors.

NOTE:• The door locks cannot be operated by

the request switch under the followingconditions: – If any door or tailgate is open or is not

completely closed.

(1)

(2)

EXAMPLE

2-8

BEFORE DRIVING

72SM0-74E

– If the ignition mode is other than“LOCK” (OFF).

• If no doors are opened within about 30seconds after unlocking the doors bypushing the request switch, the doorswill be locked again automatically.

80J056

(1) 80 cm (2 1/2 feet)

When the remote controller is withinapproximately 80 cm (2 1/2 feet) from afront door handle or the tailgate switch,which is specified as the operating range,you can lock or unlock the doors by push-ing the request switch.

NOTE:• If the remote controller is outside the

operating range described above, youwill not be able to operate the requestswitch.

• If the battery of the remote controllerruns down or there are strong radiowaves or noise, the operating range maybe reduced or the remote controller maybecome inoperative.

• If the remote controller is too close to thedoor glass, the request switches may notoperate.

• If a spare remote controller is in the vehi-cle, the request switches may not oper-ate normally.

• The remote controller will only activate arequest switch if it is within the activateoperating range. For example, if theremote controller is within the operatingrange for the driver’s door request switchbut not for the front passenger’s doorrequest switch not for the tailgaterequest switch, the driver’s door switchcan be operated but the front passen-ger’s door switch or tailgate switch can-not be operated.

NOTE:The keyless push start system may notfunction correctly in certain environmentsor under certain operating conditions suchas the followings:• When there are strong electromagnetic

wave coming from a television, powerstation or a cellular phone.

• When the remote controller is in contactwith or covered by a metal object.

• When a radio wave type remote keylessentry is used nearby.

• When the remote controller is placednear an electronic device such as per-sonal computer.

Some additional precautions you shouldtake and information you should be awareof are:

• Make sure the key is always stowed inthe remote controller. If the remote con-troller becomes unusable, you will not beable to lock or unlock the doors withoutthe key.

• Make sure that the driver always carriesthe remote controller.

• If you lose one of the remote controllers,ask a Maruti Suzuki authorised work-shop as soon as possible for a replace-ment. Be sure to have your dealerprogram the new remote controller codein your vehicle’s memory so that the oldcode is erased.

(1)

(1)

(1)

EXAMPLE

NOTICE

The remote controller is a sensitiveelectronic instrument. To avoid dam-aging the remote controller:• Do not expose it to impacts, mois-

ture or high temperature such asby leaving it on the dashboardunder direct sunlight.

• Keep the remote controller awayfrom magnetic objects such as atelevision.

2-9

BEFORE DRIVING

72SM0-74E

• You can use up to four remote control-lers and the keys for your vehicle. Ask aMaruti Suzuki authorised workshop fordetails.

• The battery life of the remote controlleris about two years, but it can varydepending on usage conditions.

52RM20080

To stow the key into the remote controller,push the key in the remote controller untilyou hear a click.

52RM20090

To remove the key from the remote control-ler, slide the lock knob (A) in the directionof the arrow and pull the key out from theremote controller.

Request switch warning buzzerThis exterior buzzer beeps for about 2 sec-onds in the following conditions to warnyou that the request switch is not working:• The request switch is pressed after all

doors and the tailgate are closed withthe ignition mode in ACC or ON positionby pressing the engine switch.

• The request switch is pressed under anyof the following conditions with the igni-tion mode in “LOCK” (OFF) position.– The remote controller is left inside the

vehicle.– Any door (including the tailgate) is

open.

To securely lock the doors and the tailgateusing the remote controller:With the ignition mode changed to “LOCK”(OFF) by pressing the engine switch, bringout the remote controller. Press therequest switch again and check that alldoors are completely locked.

EXAMPLE

(A)

EXAMPLE

2-10

BEFORE DRIVING

72SM0-74E

Reminder function

72SM02007

If the remote controller is not in the vehicleunder the following conditions, the buzzersounds intermittently for about 2 secondsand the immobilizer/keyless push start sys-tem warning light on the instrument clusterblinks:When one or more doors are opened andall of the doors are later closed with theignition mode is other than “LOCK”.While the warning light is on, the enginecan not start.

The indicator light will turn off within sev-eral seconds after the remote controller isreturned to an area of the vehicle otherthan the rear luggage area.

If the remote controller is left in the vehicleand you try to lock the driver’s door or frontpassenger’s door as described below, thedoor will be automatically unlocked.

• If you open the driver’s door and try tolock the door by turning the lock knobforward or pushing the power door lock-ing switch, the driver’s door will be auto-matically unlocked.

• If you open the front passenger’s doorand try to lock the door by turning thelock knob forward or pushing the powerdoor locking switch, the front passen-ger’s door will be automaticallyunlocked.

NOTE:• The reminder will not operate when the

remote controller is on the instrumentpanel, in the glove box, in a storagecompartment, in the sun visor or on thefloor etc.

• Be sure that the driver always carries theremote controller.

• Do not leave the remote controller in thevehicle when leaving the vehicle.

Keyless push start system remote controller battery consumption warning light

70K122

If the remote controller becomes unreli-able, this light appears on the informationdisplay for several seconds when theengine switch is pressed to change theignition mode to ON.

NOTE:If this light comes on, replace the battery,and then perform the following operation toreset the light.• Lock and unlock the doors with the

remote controller twice or more.

If the power of your spare remote controlleris enough, you can reset the light by oper-ating above procedure with the spareremote controller.

EXAMPLE

2-11

BEFORE DRIVING

72SM0-74E

Battery replacementIf the remote controller becomes unreli-able, replace the battery.

To replace the battery of the remote con-troller:

52RM20650

1) Pull the key out from the remote con-troller.

2) Insert a flat blade screwdriver coveredwith a soft cloth in the slot of the remotecontroller and pry it open.

56RH00214

(1) Button type lithium battery:CR2032 or equivalent

3) Replace the battery (1) so its + terminalfaces the bottom of the case as shownin the illustration.

4) Close the remote controller case firmly.5) Make sure the door locks can be oper-

ated with the remote controller.6) Dispose of the used battery properly

according to applicable rules or regula-tions. Do not dispose of lithium batter-ies as ordinary household trash.

NOTE:Used batteries must be disposed of prop-erly according to applicable rules or regu-lations and must not be disposed of withordinary household trash.

EXAMPLE

(1)

EXAMPLE WARNING

Swallowing a lithium battery maycause serious internal injury. Do notallow anyone to swallow a lithiumbattery. Keep lithium batteries awayfrom children and pets. If swallowed,contact a physician immediately.

NOTICE

• The remote controller is a sensitiveelectronic instrument. To avoiddamaging it, do not expose it todust or moisture or tamper withinternal parts.

• When replacing the battery byyourself, the remote controllercould be damaged affected bystatic electricity. Discharge thestatic electricity built up in yourbody by touching metal beforereplacing the battery.

2-12

BEFORE DRIVING

72SM0-74E

80JM133

(1) Crossed-out wheeled bin symbol

The crossed-out wheeled bin symbol (1)indicates that a used battery should be col-lected separately from ordinary householdtrash.

By ensuring the used battery is disposedof or recycled correctly, you will help pre-vent potential negative consequences forthe environment and human health, whichcould otherwise be caused by inappropri-ate battery disposal. The recycling ofmaterials will help to conserve naturalresources. For more detailed informationabout disposing of or recycling the usedbattery, consult a Maruti Suzuki authorisedworkshop.

Security SystemThe security system sets after you closethe all doors, engine hood. For the system to armed, you must lockthe all doors with the keyless push startsystem remote controller or request switch.

Once the system is armed, any attempt toopen a door by using any other means (*)than the keyless push start system remotecontroller, the request switch or open theengine hood will cause the alarm to be trig-gered. * These means include the following:

– The key– The lock knob on a door– The power door locking switch

Also, in case that you have set the shocksensor to enabled state and set sensitivityof the pre-warning function and full blastwarning function to a level other than 0, thealarm will be triggered if any attempt totamper with the vehicle. The shock sensorcan be selected enabled or disabled state,and sensitivity of each warning can beadjusted as desired. To set the shock sen-sor, ask your Maruti Suzuki authorisedworkshop or use the setting mode of theinformation display.

NOTE:• The default setting of the shock sensor

is in the disabled state. Set to theenabled state and adjust sensitivity ofeach warning according to your prefer-ence. For details on how to use the infor-mation display, refer to “Informationdisplay” in this section.

• Your dealer may have already set theshock sensor of the vehicle to theenabled state before you purchase it.Consult your dealer for further informa-tion.

NOTE:• The security system generates alarms

when any of the predetermined condi-tions is met. However, the system doesnot have any function of blocking unau-thorized entry into your vehicle.

• Always use the keyless push start sys-tem remote controller or the requestswitch to unlock the doors when thesecurity system has been armed. Usinga key instead will trigger the alarm.

• If a person who does not know the secu-rity system is going to drive your vehicle,we recommend you explain the systemand its operation to the person.

• Even if the security system is armed,you should still be careful to guardagainst theft. Do not leave money orthings of value in your vehicle.

(1)(1)

EXAMPLE

2-13

BEFORE DRIVING

72SM0-74E

How to arm the security systemWith the all door (including engine hoodand tailgate) closed, use the keyless pushstart system remote controller or requestswitch to lock all the doors. The securitysystem will be armed.While the system is armed, the indicator(1) continues to blink at intervals ofapproximately 2 seconds.

72SM02008

NOTE:• To prevent the alarm from being acci-

dentally triggered, avoid arming it whileanyone remains inside the vehicle. Thealarm will be triggered if any personinside opens the door, tailgate, enginehood, or swings the vehicle (if the shocksensor is in the enabled state).

• The security system is not armed whenall doors are locked using the key fromoutside, or using the door lock levers or

the power door locking switch frominside.

• If any door is not operated within approx-imately 30 seconds after the doors havebeen unlocked using the keyless pushstart system remote controller or requestswitch, the doors are automaticallylocked again. When the doors arelocked, the security system will bearmed if the system is in the enabledstate.

How to disarm the security systemSimply unlock the doors using the keylesspush start system remote controller or therequest switch. The security system indica-tor light will go out, indicating that the secu-rity system is disarmed.

How to stop the alarmShould the alarm be triggered accidentally,unlock the doors using the keyless pushstart system remote controller or therequest switch or press the engine switchto change the ignition mode to ON. Thealarm will then stop.

NOTE:• Even after the alarm has stopped, if you

lock the doors using the keyless pushstart system remote controller or requestswitch, the security system will berearmed.

• If you disconnect the lead-acid batterywhile the security system is in the armedcondition or the alarm is actually in oper-

ation, the alarm will be triggered or re-triggered when the lead-acid battery isthen reconnected, although, in the lattercase, the alarm remains stopped for theperiod between disconnection andreconnection of the lead-acid battery.

• Even after the alarm has stopped at theend of the predetermined operation time,it will be triggered again if any of thedoors, tailgate or engine hood is opened,or the vehicle feels a shock (if the shocksensor is in the enabled state), withoutdisarming the security system.

Checking whether the alarm has beentriggered during parkingIf the alarm was triggered due to an unau-thorized entry into the vehicle and you thenpress the engine switch to change the igni-tion mode to ON, the security system indi-cator light will blink rapidly for about 8seconds and a buzzer will beep 4 timesduring this period. If this happens, checkwhether your vehicle has been broken intowhile you were away from it.

(1)

EXAMPLE

2-14

BEFORE DRIVING

72SM0-74E

Security system indication• If any of the doors or tailgate are opened

without unlocking by the keyless pushstart system remote controller or requestswitch, all turn signal lights start to blinkand the interior buzzer beeps intermit-tently. After 5 seconds, the siren willsound for about 27.5 seconds. Thesecurity system indicator continues toblink during this time.

• If the engine hood is opened, all turn sig-nal lights blink, and the siren sounds forabout 27.5 seconds. The security sys-tem indicator continues to blink duringthis time.

• (If the shock sensor is in the enabledstate)The vehicle feels a shock higher thanthe pre-warning sensitivity, the sirensounds for about 2 seconds (pre-warn-ing). If the vehicle feel a shock higherthan the full blast warning sensitivity, thesiren sounds for about 5 seconds (fullblast warning). The security system indi-cator continues to blink during this time.

NOTE:If you set the full blast warning sensitivityhigher than the pre-warning sensitivity inthe setting mode of the information display,or the vehicle feels such shock as to beable to trigger the full blast warning, the fullblast warning will be triggered preferen-tially. In this case, the pre-warning will notbe triggered.

Theft deterrent light

72SM02005

This light will blink with the ignition mode“LOCK” (OFF) or “ACC”. The blinking lightis intended to deter theft by leading othersto believe that the vehicle is equipped witha security system.

NOTE:For the security system, refer to “SecuritySystem” in this section.

Windows

Power Window Controls The power windows can only be operatedwhen the ignition mode is in the ON.

Driver’s side

73R0004

The driver’s door has a switch (1) to oper-ate the driver’s window, and a switch (2) tooperate the front passenger’s window orthere are switches (3) and (4) to operatethe rear right and left passenger windows,respectively.

EXAMPLE

(3)

(1)

(2)

(4)

EXAMPLE

2-15

BEFORE DRIVING

72SM0-74E

Passenger’s door / rear door

74LHT0205

The passenger’s door/rear door has aswitch (5) to operate the passenger’s win-dow.

81A009

To open a window, push the top part of theswitch. To close the window, lift up the toppart of the switch.The driver’s window has AUTO-DOWNfeatures for greater convenience (at tollbooths or drive-through restaurants, forexample). These features allow the driverto open the window without holding thewindow switch in DOWN position. Pressdown the driver’s window switch com-pletely and release it. To stop the windowbefore it reaches the FULL-DOWN posi-tion, pull up the switch briefly.

Lock switch

73R0005

The driver’s door also has a lock switch forthe passenger’s windows. When you pushin the lock switch, the passenger’s win-dows cannot be raised or lowered by oper-ating any of the switches (2), (3), (4) or (5).

To restore normal operation, release thelock switch by pushing again.

NOTE:If you drive with one of the rear windowsopen, you may hear a loud sound causedby air vibration. To reduce the sound, openthe driver’s or front passenger’s window, ornarrow the rear window opening.

(5)EXAMPLE

CLOSE

OPEN

EXAMPLE

EXAMPLEEXAMPLE

WARNING

• You should always lock the pas-senger’s window operation whenthere are children in the vehicle.Children can be seriously injured ifthey get part of their body caughtby the window during operation.

• To avoid injuring an occupant bywindow entrapment, check that nopart of the occupant’s body such ashands or head is in the path of thepower windows when closingthem.

• Always take the keyless push startsystem remote controller with youwhen leaving the vehicle even onlyfor a short time. Also do not leavechildren alone in a parked vehicle.Unattended children could use thepower window switches and gettrapped by the window.

2-16

BEFORE DRIVING

72SM0-74E

Pinching Prevention Function The driver’s window is equipped with thepinching prevention function. The functiondetects a foreign object caught in the win-dow while being closed by the AUTO-UPfeature, by which you can close the win-dow without holding the window switch inthe UP position, and stops the windowclosing to prevent damage.

NOTE:If you cannot close the window by theAUTO UP feature because there may besomething wrong with the pinching preven-tion function, you can close the window byholding the window switch in the UP posi-tion.If you drive in extreme off-road condition,the pinching prevention function may oper-ate accidentally because the window reactto vehicle jolting.

The Pinching Prevention Function Ini-tializationWhen you disconnect and re-connect thelead-acid battery or replace the fuse, thefunction will be deactivated. In this condi-tion, the AUTO-DOWN feature will bedeactivated, while the AUTO-UP featuremay remain being activated. The pinchingprevention function needs to be initialized.

To initialize the pinching prevention func-tion, use the following procedure:1) Press the engine switch to change the

ignition mode to “ON”.2) Open the driver’s window fully by hold-

ing the window switch in the DOWNposition.

3) Close the driver’s window by holdingthe switch in the UP position, and keepholding the switch for 2 seconds afterthe window fully closed.

4) Check the driver’s window if the AUTO-DOWN/UP feature work.

If the AUTO-DOWN/UP feature would notwork after initialization, there might besomething wrong with the pinching preven-tion function. Have your vehicle inspectedby Maruti Suzuki authorised workshop.

WARNING

To avoid injuring an occupant by win-dow entrapment, be sure no part ofthe occupant’s body such as handsor head is in the path of the electricwindow when closing it.The function may not detect theobject depending on size, hardness,and position of the object caught bythe closing window.

CAUTION

• The pinching prevention functiondoes not act while you are holdingthe window switch in the UP posi-tion.

• The pinching prevention functionmay not detect an object caught inthe window just before the windowis fully closed.

WARNING

Whenever you disconnect and recon-nect the lead-acid battery or replacethe fuse, the pinching preventionfunction needs to be reinitialized. The pinching prevention function willnot be activated until the initializationcomplete.

2-17

BEFORE DRIVING

72SM0-74E

Mirrors

Inside Rearview MirrorYou can adjust the inside rearview mirrorby hand to see the rear of your vehicle inthe mirror.

68LMT0205

68LMT0206

(2) Day driving(3) Night driving

To adjust the mirror, set the selector tab (1)to the day position, and then move the mir-ror up, down or sideways by hand to obtainthe best view.When driving at night, you can move theselector tab to the night position to reduceglare from the headlights of vehiclesbehind you.

Outside Rearview MirrorsAdjust the outside rearview mirrors so youcan just see the side of your vehicle in themirrors.

73R0030

The switch to control the electric mirrors islocated on the driver’s door panel. You canadjust the mirrors when the ignition modeis “ACC” or “ON”. To adjust the mirrors:

1) Rotate the selector switch to the left orright to select the mirror you wish toadjust.

2) Push the side of the switch to the direc-tion in which you wish to move the mir-ror.

3) Return the selector switch to the centerposition to prevent unintended mirrormovement.

EXAMPLE

(1)

(2) (3)

EXAMPLE

WARNING

• Always adjust the mirror with theselector set to the day position.

• Only use the night position if it isnecessary to reduce glare from theheadlights of vehicles behind you.Be aware that in this position youmay not be able to see someobjects that could be seen in theday position.

WARNING

Be careful when judging the size ordistance of a vehicle or other objectseen in the side convex mirror. Beaware that objects look smaller andappear farther away than when seenin a flat mirror.

(1)

(2) (3)

(4)

(1)

(3

(4)

(2)

EXAMPLE

2-18

BEFORE DRIVING

72SM0-74E

Outside Rearview Mirrors Folding Switch

73R0031

You can fold the mirrors when you park thevehicle in a narrow space. When the igni-tion mode is “ACC” or “ON”, push the fold-ing switch (1) to fold and unfold themirrors.Make sure the mirrors are completelyunfolded before you start driving.

Remote folding mirrors (if equipped)When the outside rearview mirrors foldingswitch is in the unfolded position, the out-side rearview mirrors are folded orunfolded in conjunction with the door lock-ing or engine switch operation.• When you lock the doors (including the

tailgate) by using the remote controlleror pushing the request switch, the mir-rors will be folded automatically.

• To unfold the mirrors, push the engineswitch to change the ignition mode toACC or ON.

• The factory setting is that the function isenabled. You can switch the functionfrom enabled to disabled, and viceversa. To switch the function for yourpreference, refer to “How to switch theremote folding mirrors function”.

NOTE:• If the doors are locked by using the key,

lock knob on the door or power doorlocking switch, the mirrors will not befolded automatically.

• If the outside rearview mirrors foldingswitch is in the folded position, the mir-

rors will not be unfolded automatically,even when the engine switch is pushedto change the ignition mode to ACC orON.

• If any of the doors is not opened withinabout 30 seconds after the doors areunlocked by using the keyless push startsystem remote controller or requestswitch, the doors will be locked againand the mirrors will be folded automati-cally.

CAUTION

Moving mirrors can pinch and injurea hand. Do not allow any one’s handto get near the mirrors when foldingand unfolding the mirrors.

(1)

EXAMPLE

NOTICE

In cold conditions when the mirrorsare frozen, disable the function. If themirrors are folded and unfoldedrepeatedly without thawing, the mir-rors may be damaged.

2-19

BEFORE DRIVING

72SM0-74E

How to switch the remote folding mir-rors functionWhen the ignition mode is “LOCK (OFF)”,you can switch the function from theenabled state to the disabled state, andvice versa, using the following method.

1) Sit in the driver’s seat and make surethat all doors are closed.• If any door is open, the open door

warning light comes on.

68PH20004

2) Turn the lock knob (1) on the driver’sdoor rearward (2).

NOTE:All operations included in the followingsteps 3) and 4) must be completed within15 seconds.

72SM02009

3) Push the lock end (3) (forward end) ofthe power door lock switch (4) to lockthe doors, and then the unlock end (2)(backward end) to unlock the doors.Repeat the operations of this step for 4times.

72SM02010

(5) Lock button(6) Unlock button

4) Push any of the buttons on the keylesspush start system remote controller 3times.

• Push either lock button or unlock buttondescribed above you like.

• During operation, the doors are notlocked or unlocked.

Every time you perform the series of theabove steps, the state of the remote fold-ing mirrors function changes from the cur-rently selected one to the other. You cancheck whether the system is enabled ordisabled by the number of interior buzzerbeeps at the end of the procedure as fol-lows.

(1)

(2)

EXAMPLE

(4)

(3)

(2)

4 timesEXAMPLE

(5)

(6)

EXAMPLE

2-20

BEFORE DRIVING

72SM0-74E

• If you cannot complete the operations instep 3) and 4) within 15 seconds cor-rectly, the state of the remote folding mir-rors function will not change and theinterior buzzer does not beep. Performthe procedure again from the beginning.

System state Number of beeps

Disabled Once

Enabled 2 times

2-21

BEFORE DRIVING

72SM0-74E

Instrument Cluster

1. Speedometer2. Tachometer3. Fuel gauge4. Temperature gauge5. Information display6. Trip meter selector knob7. Indicator selector knob8. Warning and indicator lights

72SM02006

182

56 8 734

EXAMPLE

2-22

BEFORE DRIVING

72SM0-74E

Speedometer

72R0056

The speedometer indicates vehicle speedin km/h.

Speed Alert SystemThe speed alert system gives audiblewarning for alert of over-speed to driver.When vehicle speed exceeds about 80 km/h, primary level warning with two beeps willsound every minute. When the vehiclespeed exceeds about 120 km/h, second-ary level warning with continuous beepswill sound. If the vehicle speed is sloweddown to about 118 km/h, primary warningwill resume. If the vehicle is slowed downto about 78 km/h, speed alert warning willstop. This buzzer does not indicate anymalfunction in vehicle.

Tachometer

72R0057

The tachometer indicates engine speed inrevolutions per minute.

Fuel gauge

72R0058

When the ignition mode is “ON”, thisgauge gives a rough indication of theamount of fuel in the fuel tank. “F” standsfor full and “E” stands for empty.

If the indicator approaches a low level(near “E”) on fuel gauge, refill the tank assoon as possible.

NOTE:The indicator moves a little depending onroad conditions (for example, slope orcurve) and driving conditions because offuel moving in the tank.

EXAMPLE

NOTICE

Never drive the vehicle with theengine revving in the red zone orsevere engine damage can result.Keep the engine speed below the redzone even when downshifting to alower gear position.Refer to “Downshifting maximumallowable speeds” in the “OPERAT-ING YOUR VEHICLE” section.

EXAMPLE

(1)

(2)

EXAMPLE

2-23

BEFORE DRIVING

72SM0-74E

If the low fuel warning light (1) comes on,refill the fuel tank as soon as possible.

NOTE:The activation point of the low fuel warninglight (1) varies depending on road condi-tions (for example, slope or curve) anddriving conditions because of fuel move-ment in the tank.

Refer to “Low fuel warning light” in “Warn-ing and indicator lights” in this section fordetails.

The mark (2) indicates that the fuel fillerdoor is located on the left side of the vehi-cle.

Temperature Gauge

72R0059

When the ignition mode is “ON”, thisgauge indicates the engine coolant tem-perature. Under normal driving conditions,the indicator should stay within the normal,acceptable temperature range between“H” and “C”. If the indicator approaches“H”, overheating is indicated. Follow theinstructions for engine overheating in“EMERGENCY SERVICE” section.

Brightness Control

72R0063

72R0060

NOTICE

Continuing to drive the vehicle whenengine overheating is indicated canresult in severe engine damage.

EXAMPLE EXAMPLE

(1) EXAMPLE

2-24

BEFORE DRIVING

72SM0-74E

When the ignition is pushed to “ON” mode,the instrument panel lights come on.

Your vehicle has a system to automaticallydim the brightness of the instrument panellights when the position lights or headlightsare on.

When the position lights and/or headlightsare ON, you can control the meter illumina-tion intensity.

To increase the brightness of the instru-ment panel lights, turn the brightness con-trol knob (1) clockwise.

To reduce the brightness of the instrumentpanel lights, turn the brightness controlknob (1) counterclockwise.

NOTE:• If you do not turn the brightness control

knob within several seconds of activat-ing, the brightness control display will becanceled automatically.

• When you reconnect the lead-acid bat-tery, the brightness of the instrumentpanel lights will be reinitialized. Readjustthe brightness according to your prefer-ence.

NOTE:If you adjust to the maximum brightnesslevel when the position lights or headlightsare on, the following functions will be can-celled.• The function which automatically dims

the brightness of instrument panel lights.• The function which operates with the

brightness control, except maximumbrightness level.

Information DisplayThe information display is shown when theignition mode is “ON”.

72R0061

1. Information display

72R0062

WARNING

Do not adjust the brightness of theinstrument panel lights while driving.Otherwise, you could lose control ofthe vehicle.

(D) (E)(F)

(A) (B)

(C)

(D) (E)(F)

(A) (B)

(C)

(1)

EXAMPLE

(2) (3)

EXAMPLE

2-25

BEFORE DRIVING

72SM0-74E

(2) Trip meter selector knob(3) Indicator selector knob

The information display shows the follow-ing information.

Display (A)Clock

Display (B)Thermometer

Display (C)Fuel consumption / Driving range / Aver-age speed / Driving time / Total idling stoptime and Total idling fuel saved (ifequipped) / Clock and date / Motion (ifequipped) / Torque and power (ifequipped) / Accelerator and brake (ifequipped) / Energy flow (if equipped)

Display (D)Selector position (for automatic transmis-sion vehicles) / Gearshift indicator (formanual transmission vehicles)

Display (E)Trip meter

Display (F)Odometer

72R0135

When ignition mode is made “ON”, mes-sage shown in above illustration willappear on display for several seconds.

Some warning and indicator messagesmay appear on the display when the igni-tion mode is “ACC” or “LOCK” (OFF).

ClockWhen the ignition mode is “ON”, the dis-play (A) shows the time.

To set the clock, follow “Setting mode”instructions in this section.

Thermometer When the ignition mode is “ON”, the dis-play (B) shows the thermometer.

The thermometer indicates the outsidetemperature.

52RM21050

If the outside temperature nears freezingcondition, the message shown in theabove illustration will appear on the dis-play.

WARNING

If you attempt to adjust the displaywhile driving, you could lose controlof the vehicle.Do not attempt to adjust the displaywhile driving.

EXAMPLE

EXAMPLE

2-26

BEFORE DRIVING

72SM0-74E

NOTE:• The outside temperature indication is not

the actual outside temperature whendriving at low speed, or when stopped.

• If there is something wrong with the ther-mometer, or just after the ignition ispushed to “ON” mode, the display maynot indicate the outside temperature.

You can change the unit of temperature.To change the unit of temperature, refer to“Setting mode” in this section.

Fuel Consumption / Driving Range / Average Speed / Driving Time / Total Idling Stop Time and Total Idling Fuel Saved (if equipped) / Clock and Date / Motion (if equipped) / Torque and Power / Accelerator and Brake (if equipped) / Energy flow (if equipped)When there are no warning or indicatormessages on the display (C), you canselect one of the following indications toappear on the display: instantaneous fuelconsumption, average fuel consumption,driving range, average speed, driving time,total idling stop time and total idling fuelsaved (if equipped), clock and date, motion(if equipped), torque and power, accelera-tor and brake (if equipped), energy flow (ifequipped) or no indication.

2-27

BEFORE DRIVING

72SM0-74E

72RM02002

(a) Instantaneous fuel consumption / Average fuel consumption / Driving range(b) Instantaneous fuel consumption / Average fuel consumption / 5-minute average fuel

consumption / 1-driving cycle average fuel consumption(c) Average speed / 5-minute average speed / Driving time(d) Total idling stop time / Total idling fuel saved (if equipped)(e) Clock and date(f) Motion (if equipped)(g) Torque and power(h) Accelerator and brake (if equipped)(i) Energy flow (if equipped)(j) No indication

(j) (i)

(a) (b) (c)

(f)

(e)(d)

(g)(h)

EXAMPLETo switch the display indication, push theindicator selector knob (3) quickly.

NOTE:The value of instantaneous fuel consump-tion, average fuel consumption, drivingrange, average speed, total idling fuelsaved (if equipped), motion (if equipped),torque and power, accelerator and brake (ifequipped) and energy flow (if equipped)shown on the display are affected by thefollowing conditions; • road condition• surrounding traffic condition• driving condition• vehicle condition• a malfunction which causes the malfunc-

tion indicator light to come on or blink

2-28

BEFORE DRIVING

72SM0-74E

Instantaneous fuel consumptionThe display shows instantaneous fuel con-sumption with a bar graph only when thevehicle is moving.

52RM21070

(4) Instantaneous fuel consumption

NOTE:• The display does not show the bar graph

unless the vehicle is moving.• Depending on the vehicle’s specification,

the fuel consumption units of initial set-ting are indicated as L/100km, km/L,MPG (UK).

• The indicated maximum value of instan-taneous fuel consumption is one of thefollowings. No more than the maximumvalue will be indicated on the displayeven if the actual instantaneous fuelconsumption is higher.– For L/100km setting: 30– For km/L setting: 50– For MPG (UK) setting: 80

• The indication on the display may bedelayed if fuel consumption is greatlyaffected by driving conditions.

• The display shows estimated values.Indications may not be the same asactual values.

Average fuel consumption / 5-minuteaverage fuel consumption / 1-drivingcycle average fuel consumptionAverage fuel consumption from previousreset and 5-minute average fuel consump-tion, and 1-driving cycle average fuel con-sumption are shown.

(Average fuel consumption)

52RM21080

(5) Average fuel consumption

If you selected average fuel consumptionthe last time you drove the vehicle, the dis-play shows the last value of average fuelconsumption from previous driving whenthe ignition is pushed to “ON” mode.Unless you reset the value of average fuelconsumption, the display indicates thevalue of average fuel consumption basedon the average fuel consumption duringprevious driving.

NOTE:When you reconnect the negative (–) ter-minal to the lead-acid battery, the value ofaverage fuel consumption will be shownafter driving for a period of time.

You can select the timing to reset the valueof average fuel consumption by one of thefollowing three methods; • Reset after refuel: the value of average

fuel consumption will be reset automati-cally by refueling.

• Reset with trip meter A: the value ofaverage fuel consumption will be resetautomatically by resetting trip meter A.

• Reset manually: the value of averagefuel consumption will be reset by push-ing and holding the indicator selectorknob (3) when the display indicates theaverage fuel consumption.

To change the timing to reset the value ofaverage fuel consumption, refer to “Settingmode” in this section.

(4)EXAMPLE

(5)

(5)

EXAMPLE

2-29

BEFORE DRIVING

72SM0-74E

NOTE:If you add only a small amount of fuelwhen you select “Reset after refuel”, theaverage fuel consumption value may notbe reset.

(5-minute average fuel consumption)

72R0136

(6) 5-minute average fuel consumption

(1-driving cycle average fuel consump-tion)

72RM02003

(7) 1-driving cycle average fuel con-sumption

You can check transition of average fuelconsumption every 5 minutes from 15 min-utes before up to now. Also, you can checktransition of average fuel consumption thepast 3 driving cycles. Time indication anddriving cycle indication can be changed.For details, refer to “Setting mode” in thissection.

Driving range

52RM21090

(8) Driving range

If you selected driving range the last timeyou drove the vehicle, the display indicates“---” for a few seconds and then indicatesthe current driving range when the ignitionis pushed to “ON” mode.

The driving range shown in the display isthe approximate distance you can driveuntil the fuel gauge indicates “E”, based oncurrent driving conditions.

When the low fuel warning light comes on,the display “---” will appear. If the low fuelwarning light comes on, fill the fuel tankimmediately regardless of the value of driv-ing range shown in the display.

(6)

EXAMPLE

(7)

EXAMPLE

(8)

EXAMPLE

2-30

BEFORE DRIVING

72SM0-74E

When you refuel, the driving range isupdated. However, if you only add a smallamount of fuel, the correct value will not bedisplayed.

NOTE:• If you refuel when the ignition mode is

“ON”, the driving range may not indicatethe correct value.

• When you reconnect the negative (–)terminal to the lead-acid battery, thevalue of driving range will be shown afterdriving for a period of time.

Average speed / 5-minute averagespeedAverage speed from previous reset and 5-minute average speed are shown.

(Average speed)

52RM21100

(9) Average speed

If you selected average speed the last timeyou drove the vehicle, the display indicatesthe last value of average speed from previ-ous driving when the ignition is pushed to“ON” mode. Unless you reset the value ofaverage speed, the display indicates thevalue of average speed which includesaverage speed during previous driving.

To reset the value of average speed, pushand hold the indicator selector knob (3) forabout 2 seconds when the display indi-cates an average speed. The displayshows “---” and then indicates a new aver-age speed after driving for a short time.

NOTE:When you reconnect the negative (–) ter-minal to the lead-acid battery, the value ofaverage speed will be shown after drivingfor a period of time.

(5-minute average speed)

52RM21110

(10) 5-minute average speed

You can check transition of 5-minute aver-age speed every 5 minutes from 10 min-utes before up to now.

(9)

EXAMPLE

(10)

EXAMPLE

2-31

BEFORE DRIVING

72SM0-74E

Driving time

52RM21120

(11) Driving time

Driving time from previous reset is shown.To reset the driving time, push and hold theindicator selector knob (3) for about 2 sec-onds when the display indicates a drivingtime. The display shows “---” and then indi-cates a new driving time after driving for ashort time.

NOTE:• Disconnection of the lead-acid battery

negative (-) terminal will reset the indica-tion of the driving time.

• The indicated maximum value of drivingtime is 99:59:59. No more than thisvalue will be indicated on the displayuntil you reset the driving time.

Total idling stop time and total idlingfuel saved (if equipped)

52RM217

(12) Total idling stop time(13) Total idling fuel saved

The display shows the total length (inhours, minutes and seconds) of enginestopping time and the total amount (in milli-liters) of fuel conservation by ENG A-STOP system since the indication wasreset.• To reset the total idling stop time and the

total idling fuel saved, push and hold theindicator selector knob (3) for a whilewhen the display shows the total idlingstop time and the total idling fuel saved.

NOTE:• The indicated maximum value of the

total idling stop time is 99:59:59 and thisvalue is fixed until it is reset.

• When you reconnect the negative (–)terminal to the lead-acid battery, thevalue of the total idling stop time and thetotal idling fuel saved will be reset.

Clock and dateDate and time are shown. For the settingprocedure, refer to “Setting mode” in thissection.

Motion

52RM218

The meter indication is different dependingon whether the vehicle is stopped or run-ning.

When driving, real time movement of ima-ginal G position (center of gravity) is dis-played on the globe (14), which is resultantwith inertia force.

When stopped, historical data of imaginalG positions applied to the vehicle body

(11)

EXAMPLE

(13)

(12)

EXAMPLE

(14) (15) EXAMPLE

2-32

BEFORE DRIVING

72SM0-74E

during the driving is shown as a graph(15).

G position history graph when the vehiclestopped can be changed to indicate orhide. For details, refer to “Setting mode” inthis section.

NOTE:• If G position history graph at the vehicle

stopped has been set in indicationmode, the graph (15) is shown for sev-eral seconds when you change the igni-tion mode to “LOCK” (OFF) after driving.

• The graph is shown approximately andthe actual movement may differ.

Torque and powerPresent engine torque and power areshown.

Accelerator and brake (if equipped)Present accelerator pedal depressingdegree and brake line pressure are shown.The display is selectable to indicate or notto indicate. For details, refer to “Settingmode” in this section.

WARNING

Do not look in the display intensivelywhile driving. Doing so may result inan accident.

Energy flow (if equipped)The state of Smart Hybrid operation can be checked on the information display. Fordetails, refer to “Smart Hybrid” in “OPERATING YOUR VEHICLE” section.

Information display Description

72RM02004

When the vehicle is running, ISG (Integrated Starter Gen-erator) assists engine power as an electric motor.

72RM02005

When the vehicle is powered by the engine.

72RM02006

When decelerating your vehicle, the ISG generates elec-tricity without engine power.

72RM02007

When the engine automatically stops by the ENG A-STOPsystem.

2-33

BEFORE DRIVING

72SM0-74E

Information shown after drivingWhen you press the engine switch tochange the ignition mode to “LOCK”(OFF), the following information appearsfor several seconds on the information dis-play.

52RM21140

Selector position (for automatic transmission vehicles) / Gearshift Indicator (for manual transmission vehicles)

52RM242

Selector position (for automatic trans-mission vehicles)When the engine switch is pressed tochange the ignition mode to “ON”, the dis-play (D) indicates the gear position (l).

For details on how to use the transmission,refer to “Using transmission” in “OPERAT-ING YOUR VEHICLE” section.

Gearshift Indicator (for manual trans-mission vehicles)Refer to “Gearshift indicator” in “OPERAT-ING YOUR VEHICLE” section.

Trip meterThe display (E) shows the trip meter.

The trip meter can be used to measure thedistance traveled on short trips or betweenfuel stops.You can use trip meter A or trip meter Bindependently.

To reset the trip meter, push and hold thetrip meter selector knob (2) for about 2seconds when the display shows the tripmeter.

OdometerThe display (F) shows the odometer.

The odometer records the total distancethe vehicle has been driven.

EXAMPLE(l)(l)

EXAMPLE

NOTICE

Keep track of your odometer readingand check the maintenance sched-ule regularly for required services.Increased wear or damage to certainparts can result from failure to per-form required services at the propermileage intervals.

2-34

BEFORE DRIVING

72SM0-74E

Setting ModeWhen the ignition mode is “ON” and thevehicle is stationary, you can enter into thesetting mode of the information display bypushing and holding the indicator selectorknob (3) for more than 3 seconds.

• To select the setting item that you wantto change, turn the indicator selectorknob (3) left or right.

• To change the setting, push the indicatorselector knob (3).

• To exit the setting mode, select “Back”and push the indicator selector knob (3).

72R0142

NOTE:The currently selected setting item is sur-rounded by a frame.

NOTE:• If you push and hold the indicator selec-

tor knob (3) to enter into the settingmode when the display (C) shows aver-age fuel consumption, average speed,driving time, total idling stop time andtotal idling fuel saved (if equipped), thevalue will be reset simultaneously. If youdo not want to reset the value, push theindicator selector knob quickly to switchthe indication of the display.

• If you press the engine switch or start tomove the vehicle when the display is inthe setting mode, the setting mode willbe canceled automatically.

Distance unit(Odometer / trip meter / driving range /average speed distance unit setting)You can change the units in which odome-ter / trip meter / driving range / averagespeed distance is displayed.

Fuel economy(Fuel consumption unit setting)You can change the units that fuel con-sumption is displayed in.

LanguageYou can change the language of the infor-mation display.

Fuel reset(Average fuel consumption reset set-ting)You can change when the value of aver-age fuel consumption is reset.

Temperature(Temperature unit setting) (if equipped)You can change the units that temperatureis displayed in.• To change the temperature unit, select

“Temperature” in “Setting mode”. Then,select “°C” or “°F”.

NOTE:When you change the units that tempera-ture is displayed in, the automatic heatingand air conditioning system temperaturedisplay units will be changed automatically.

Set sensors (Parking sensor setting) The parking sensor can be switchedbetween the normal mode and trailermode.

Clock setting(Adjusting the clock)• Adjust the clock by selecting “Clock set-

ting” in “Setting mode”. Then, select“Adjust clock”.

• To change the hour indication, turn theindicator selector knob (3) left or rightrepeatedly when the hour indicationblinks. To change the hour indicationquickly, turn and hold the indicator selec-

EXAMPLE

2-35

BEFORE DRIVING

72SM0-74E

tor knob (3). To set the hour indication,push the indicator selector knob (3) andthe minute indication blinks.

• To change the minute indication, turn theindicator selector knob (3) left or rightrepeatedly when the minute indicationblinks. To change the minute indicationquickly, turn and hold the indicator selec-tor knob (3). To set the minute indication,push the indicator selector knob (3).

(Selecting 12H/24H format)• Switch the time indication between 12-

hour and 24-hour format by selecting“Clock setting” in “Setting mode”. Then,select “12H” or “24H”.

(Adjusting the date)• Adjust the date by selecting “Clock set-

ting” in “Setting mode”. Then select“Adjust date”.

• To adjust year, month and day, operatethe indicator selector knob (3) in thesame way as adjusting the clock.

Door lock (Door lock setting)(Door unlock)• All Doors:

Unlock all doors by keyless push startsystem remote controller or requestswitch once

• Driver Door: Unlock all doors by keyless push startsystem remote controller or requestswitch twice (default setting)

(Auto lock)• Manual Lock:

Disable the automatic door locking func-tion

• Speed Syncro: Lock all doors when the vehicle speedreaches 15 km/h (default setting)

• Shift Syncro: (For automatic transmission vehicle) Lock all doors when the gearshift lever isin other than “P”.

(Auto unlock)• Syncro Off:

Disable the automatic door unlockingfunction (default setting for the vehiclewith the keyless push start system)

• Shift Syncro: (For automatic transmission vehicle) Unlock all doors when the gearshift leveris moved to the “P” from other position.

• IG-OFF Sync: Unlock all doors when the engine switchis pressed to change the ignition modeto LOCK (OFF) (default setting for thevehicle without the keyless push startsystem)

(Alarm)• You can turn off or on the siren sound

when the door(s) is(are) locked orunlocked.

Lights(Lane change setting)The turn signal and its indicator can be setwhether they flash three times even if youreturn the turn signal control lever immedi-ately after moving it.

(Guide me light setting) (if equipped)You can change the lighting time of “Tocar” function or “To home” function.

Antitheft(Shock sensor system setting)You can change the on/off of the shocksensor.

(Shock sensor P setting)You can adjust the pre-warning sensitivityof shock sensor.

(Shock sensor F setting)You can adjust the full blast warning sensi-tivity of shock sensor.

IS A/C(ENG A-STOP system setting) • When the automatic air conditioning sys-

tem is turned ON, you can select one ofthe following engine auto stop settings.– Standard– Economy– Comfort

• When “Economy” is selected, comparedwith “Standard” the engine auto stopcondition will occur more frequently, thestop time will be longer, leading to reduc-tion of fuel consumption.

2-36

BEFORE DRIVING

72SM0-74E

• When “Comfort” is selected, comparedwith “Standard” the engine auto stopcondition will occur less frequently, thestop time will be shorter, leading to morecomfortable cabin condition by the airconditioning system.

Display item(“Car color” setting)You can change the car color of the infor-mation display.

(“Calendar dis” setting)You can select whether you show the cal-ender on the information display or not.

(“Calendar form” setting)You can change the calendar form of theinformation display.To change the calendar form, select “Cal-endar form” in “Display item”. Then, selectthe display order of date, month and year.

(“Fuel eco hist” setting)Transitional indication of average fuel con-sumption can be switched to time indica-tion and driving cycle indication.

(“Motion hist” setting) (if equipped)Indication of G position history graph at thevehicle stopped can be selected to enableor disable.

(“Idling disp” setting) (if equipped)Display of ENG A-STOP operation withignition mode “LOCK” (OFF) is selectableto indicate or not to indicate.

(“Idling warn” setting) (if equipped)You can switch whether the informationdisplay shows the warning and indicatormessages related on the ENG A-STOPsystem.

(“Pedal op disp” setting) (if equipped)Display of “Accelerator and brake” isselectable to indicate or not to indicate.

Eco lighting (if equipped)Information display can be set to showcolor blue always or to three color light toindicate driving modes.

Default(initialization setting)If you select “YES” and push the indicatorselector knob (3), all settings will be reini-tialized.

Warning and Indicator MessagesThe display shows warning and indicatormessages to let you know about certainvehicle problems.A tone may also sound to alert you.

If warning and indicator messages appearon the display, follow the messages.

Master warning indicator light

80P0382

When the display shows warning and indi-cator messages, the master warning indi-cator light may also blink.

NOTE:• When the problem that causes a mes-

sage to appear is corrected, the mes-sage will disappear.

• If a message is displayed, and otherproblems requiring a message occur, themessage for each of the problems willbe alternately displayed about every 5seconds.

• When you push and hold the indicatorselector knob (2) for about 2 secondswhile a message is displayed, the mes-sage will disappear temporarily. If theproblem that caused the message is notcorrected, the message will appearagain after 5 seconds.

2-37

BEFORE DRIVING

72SM0-74E

Warning and indicator messages

All model

(#1) This message will disappear after a while even if the problem that caused the message to appear is not corrected.

Warning and indicator message

Master warning indicator light Sound Cause and remedy

72RM02008

Blinks (only while vehicleis in motion)

Beep (one time from interiorbuzzer; only while vehicle isin motion)

A door or tailgate is not properly closed.Stop the vehicle in a safe place and closethe door or tailgate properly. (#1)

52RS005

Blinks Continuous beep (from inte-rior buzzer)

The parking brake is not released. Stop thevehicle in a safe place and release the park-ing brake.

2-38

BEFORE DRIVING

72SM0-74E




52RM21170

Blinks Continuous beep (from inte-rior buzzer)

The headlights and/or the position lights areleft on. Turn them off.

52RM21180

Off Beep (one time from interiorbuzzer)

Fuel is low. Refill it immediately. (#1)

2-39

BEFORE DRIVING

72SM0-74E




52RM21190

Off Off The road may be icy. Drive very carefully.(#1)

2-40

BEFORE DRIVING

72SM0-74E

Vehicle with keyless push start system




52RM21210

Off Off This message is displayed when “ACC”position is selected as the ignition mode.(#1)

52RM21220

Off Off The brake pedal (for automatic transmissionmodels) or the clutch pedal (for manualtransmission models) is depressed. Pressthe engine switch to start the engine.

2-41

BEFORE DRIVING

72SM0-74E



52RM21230

Blinks Beep (one time from interiorbuzzer)

There is a problem with the steering locksystem.Have your vehicle inspected by a MarutiSuzuki authorised workshop.

52RM21240


There is a problem with the immobilizer/keyless push start system. Also, the vehiclelead-acid battery voltage may bedecreased.When the message is displayed even if youstart the engine with normal voltage of thevehicle lead-acid battery, have your vehicleinspected by a Maruti Suzuki authorisedworkshop.

2-42

BEFORE DRIVING

72SM0-74E



52RM21250

52RM21260

Blinks By certain conditions, somekind of sound you will hearfrom interior and/or exterior ofthe vehicle.

The remote controller may be outside thevehicle or its battery may have become dis-charged. Locate the remote controller ortouch the engine switch with the remotecontroller.If the message still appears, replace theremote controller battery.

2-43

BEFORE DRIVING

72SM0-74E




52RM21270

Off Off This message is displayed when “ON” posi-tion is selected as the ignition mode. (#1)

52RM21280


The steering lock is not disengaged. Whilelightly turning the steering wheel in bothdirections, press the engine switch again.

2-44

BEFORE DRIVING

72SM0-74E




52RM21290

Off Off The remote controller battery is about tobecome flat. Replace the battery. (#1)

Manual transmission

52RM21300

Off Off The engine switch is pressed withoutdepressing the brake and clutch pedals. Tryagain as instructed by the message.

2-45

BEFORE DRIVING

72SM0-74E



Automatic transmission

52RM21310

Off Off The engine switch is pressed with the gear-shift lever in a position other than “P” or “N”and depressing the brake pedal. Try againas instructed by message.

Automatic transmission

52RM21320

Off Off The engine switch is pressed with the gear-shift lever in a position other than “P”. Tryagain as instructed by the message.

2-46

BEFORE DRIVING

72SM0-74E

Vehicle with ESP® system



52RM21340


There may be a problem with ESP® system.Have your vehicle inspected by a MarutiSuzuki authorised workshop.

Hill hold control system

52RM21350


There may be a problem with hill hold con-trol system (if equipped).Have your vehicle inspected by a MarutiSuzuki authorised workshop.

2-47

BEFORE DRIVING

72SM0-74E

Warning and Indicator Lights

Brake System Warning Light

82K170

Three different types of operations existdepending on the vehicle’s specification.

• The light comes on briefly when the igni-tion is pushed to “ON” mode.

• The light comes on when the parkingbrake is engaged with the ignition mode“ON”.

• The light comes on under either or bothof above two conditions.

The light also comes on when the fluid inthe brake fluid reservoir falls below thespecified level.

The light should go out after starting theengine and fully releasing the parkingbrake, if the fluid level in the brake fluidreservoir is adequate.

The light also comes on together with theABS warning light when the rear brakeforce control function (proportioning valvefunction) of the ABS system fails.

If the brake system warning light comes onwhile you are driving the vehicle, it maymean that there is something wrong withthe vehicle’s brake system. If this happens:

1) Pull off the road and stop carefully.

2) Test the brakes by carefully starting andstopping the vehicle on the shoulder ofthe road.

3) If you determine that it is safe, drive thevehicle cautiously at low speed to thenearest Maruti Suzuki authorised work-shop for repairs or tow the vehicle tothe nearest Maruti Suzuki authorisedworkshop for repairs.

NOTE:Because the brake system is self-adjust-ing, the fluid level will drop as the brakepads become worn. Replenishing thebrake fluid reservoir is considered normalperiodic maintenance.

NOTE:A buzzer sounds intermittently to remindyou to release the parking brake if youstart the vehicle without releasing the park-ing brake. Make sure that the parkingbrake is fully released and the brake sys-tem warning light turns off.

WARNING

Remember that stopping distancemay be longer, you may have to pushharder on the pedal, and the pedalmay go down farther than normal.

WARNING

If any of the following conditionsoccur, you should immediately ask aMaruti Suzuki authorised workshopto inspect the brake system.• If the brake system warning light

does not go out after the enginehas been started and the parkingbrake has been fully released.

• If the brake system warning lightdoes not come on when the igni-tion is pushed to “ON” mode.

• If the brake system warning lightcomes on at any time during vehi-cle operation.

2-48

BEFORE DRIVING

72SM0-74E

Anti-Lock Brake System (ABS)

Warning Light

65D529

When the ignition is pushed to “ON” mode,this light comes on briefly so you cancheck that the light is working.If the light stays on, or comes on whendriving, there may be something wrongwith the ABS.

If this happens: 1) Pull off the road and stop carefully.2) Change the ignition mode to “LOCK”

(OFF) by pressing the engine switchand then start the engine again.

If the warning light comes on briefly andthen turns off, the system is normal. If thewarning light still stays on, something iswrong with the system.

If the light and the brake system warninglight stay on or come on simultaneouslywhen driving, your ABS system isequipped with the rear brake force controlfunction (proportioning valve function) andthere may be something wrong with boththe rear brake force control function andthen anti-lock function of the ABS system.

If one of the above occurs, have the sys-tem inspected by a Maruti Suzuki autho-rised workshop.If the ABS becomes inoperative, the brakesystem will function as an ordinary brakesystem that does not have this ABS sys-tem.

For details of ABS system, refer to “Anti-Lock Brake System (ABS)” in “OPERAT-ING YOUR VEHICLE” section.

Oil Pressure Warning Light

50G051

When the ignition is pushed to “ON” mode,this light comes on. When the engine isstarted, the light goes out. The light willcome on and remain on if there is insuffi-cient oil pressure. If the light comes onwhen driving, pull off the road as soon asyou can and stop the engine. Check the oil level and add oil if necessary.If there is enough oil, the lubrication sys-tem should be inspected by a MarutiSuzuki authorised workshop before youdrive the vehicle again.

ESP® Warning Light (if equipped)

52KM133

ESP® is a registered trademark of DaimlerAG.

This light blinks 5 times per second whenone of the following systems is activated.• Stability control system• Traction control system

If this light blinks, drive carefully.

When the ignition is pushed to “ON” mode,the light comes on briefly so you can checkthat the light is working. If the light stays onor comes on when driving, there may besomething wrong with the ESP® systems(other than ABS). You should have thesystem inspected by a Maruti Suzukiauthorised workshop.

ABSABS

NOTICE

• If you operate the engine with thislight on, severe engine damage canresult.

• Do not rely on the oil pressure lightto indicate the need to add oil. Peri-odically check the engine oil level.

2-49

BEFORE DRIVING

72SM0-74E

For details of the ESP® systems, refer to“Electronic Stability Program (ESP®) (ifequipped)” in “OPERATING YOUR VEHI-CLE” section.

ESP® OFF Indicator Light (if equipped)

73R0196

When the ignition is pushed to “ON” mode,this light comes on briefly so you cancheck that the light is working.

When the ESP® OFF switch is pushed toturn off the ESP® systems (other thanABS), the ESP® OFF indicator light comeson and stays on.

For details of the ESP® systems, refer to“Electronic Stability Program (ESP®) (ifequipped)” in “OPERATING YOUR VEHI-CLE” section.

Charging Light

50G052

When the ignition is pushed to “ON” mode,this light comes on. When the engine isstarted, the light goes out. The light willcome on and remain on if there is some-thing wrong with the lead-acid batterycharging system. If the light comes onwhen the engine is running, the chargingsystem should be inspected immediatelyby a Maruti Suzuki authorised workshop.

Driver’s seat belt reminder light /Front passenger’s seat belt reminder light

60G049

When the driver or front passenger doesnot buckle his or her seat belt, this light willcome on and/or blink.For details of the seat belt reminder, referto “Seat Belts and Child Restraint Sys-tems” in “FOR SAFE DRIVING” section.

AIRBAG Light

63J030

When the ignition is pushed to “ON” mode,this light comes on for several seconds soyou can check that the light is working.

The light will come on and stay on if thereis a problem in the airbag system or theseat belt pretensioner system.

WARNING

The ESP® systems cannot preventaccidents. Always drive carefully.

2-50

BEFORE DRIVING

72SM0-74E

Malfunction Indicator Light

63J031

Your vehicle has a computer-controlledemission control system. A malfunctionindicator light is provided on the instrumentcluster to indicate when it is necessary tohave the emission control system serviced.When the ignition is pushed to “ON” mode,this light comes on. When the engine isstarted, the light goes out.

If the malfunction indicator light comes onor blinks when the engine is running, there

is a damage in the emission control sys-tem.Bring the vehicle to a Maruti Suzuki autho-rised workshop to have the damage fixed.

Also, if this light comes on when theengine is running, there is a problem withthe automatic transmission system. Ask aMaruti Suzuki authorised workshop tohave the system inspected.

Transmission Warning Light (if equipped)

81A262

When the ignition is pushed to “ON” mode,this light comes on for several seconds soyou can check that the light is working.

If this light comes on when the engine isrunning, there is a problem with the auto-matic transmission system. Ask a MarutiSuzuki authorised workshop to have thesystem inspected.

WARNING

If the AIRBAG light does not blink orcome on briefly when the ignition ispushed to “ON” mode, stays on formore than 10 seconds, or comes onwhile driving, the airbag system orthe seat belt pretensioner systemmay not work properly, which couldresult in serious injury in the event ofa collision. Have both systemsinspected by a Maruti Suzuki autho-rised workshop.

CAUTION

If this light blinks, stop your vehicleimmediately in a safe place to avoidcatalyst's melting problem sincethere may be a misfire in the engine.• Do not drive or stop over such as

withered grasses.• Drive slowly if required to move the

vehicle.

NOTICE

Continuing to drive the vehicle whenthe malfunction indicator light is onor blinking can cause permanentdamage to the vehicle’s emissioncontrol system, and can affect fueleconomy and driveability.

2-51

BEFORE DRIVING

72SM0-74E

Immobilizer/Keyless Push Start System Warning Light

80JM122


If this light blinks or stays on, there is aproblem with the system or the steeringlock cannot be released. If this happens,press the engine switch, turning the steer-ing wheel to the right or left. If this light stillblinks or stays on even if you start theengine with normal voltage of the vehiclelead-acid battery, ask a Maruti Suzukiauthorised workshop.

Open Door Warning Light

54G391

This light remains on until all doors (includ-ing the tailgate) are completely closed.

If any door (including the tailgate) is openwhen the vehicle is moving, a ding soundsto remind you to close all doors completely.

Main Beam (high beam) Indicator Light

50G056

This indicator comes on when headlightmain beams (high beams) are turned on.

Low Fuel Warning Light

54G343

If this light comes on, refuel the fuel tankas soon as possible.

When this light comes on, a ding soundsonce to remind you to refuel.If you do not refuel, a ding sounds everytime when the ignition is pushed to “ON”mode.

NOTE:The activation point of this light variesdepending on road conditions (for exam-ple, slope or curve) and driving conditionsbecause of fuel movement in the tank.

2-52

BEFORE DRIVING

72SM0-74E

Electric Power Steering Light

79J039

When the ignition is pushed to “ON” mode,this light comes on. When the engine isstarted, the light goes out.

If this light comes on while driving, thepower steering system may not work prop-erly. Have the system inspected by aMaruti Suzuki authorised workshop.

NOTE:The following steering wheel operationsmay gradually take more effort while park-ing or driving at a very low speed. This isnot a malfunction of the steering system,but the power steering control system lim-its the power assist in order to prevent itfrom overheating.• The steering wheel is operated very

often.• The steering wheel is kept in a fully

turned position for a long while.When the power steering control systemcool down, the power steering system willreturn to its original condition.However, repeating these operations couldcause damage to the power steering sys-tem.

• This light comes on when continuingperiod of time of limiting the power assistin order to prevent from overheating.

NOTE:If the power steering system does not workproperly, it will require greater effort tosteer, but you still will be able to steer.

NOTE:If the steering is operated, you may hearnoise caused by electric power steeringoperation. This is normal and indicates thatthe power steering system works properly.

Turn Signal Indicators

50G055

When you turn on the left or right turn sig-nals, the corresponding green arrow on theinstrument panel will blink along with therespective turn signal lights. When youturn on the hazard warning switch, botharrows will blink along with all of the turnsignal lights.

Illumination Indicator Light

64J045

This indicator light comes on while theposition lights, tail light and/or the head-lights are on.

2-53

BEFORE DRIVING

72SM0-74E

Front Fog Light Indicator Light

68PM00268

The front fog light indicator light comes onwhen the front fog light operates.

Over Drive Off Indicator (if equipped)

73R0047

This light comes on when OD switch isOFF.

ENG A-STOP Indicator Light

72M00032

When the ignition mode is in “ON”, thislight comes on briefly so you can checkthat the light is working.

When the engine stops automatically, thislight comes on.

For details, refer to “ENG A-STOP System(Engine Auto Stop Start System)” in“OPERATING YOUR VEHICLE” section.

ENG A-STOP OFF Light

72M00159

When the ignition mode is in “ON”, thislight comes on briefly so you can checkthat the light is working.

When you push the ENG A-STOP OFFswitch, this light comes on.

If this light blinks when driving, there maybe something wrong with the ENG A-STOP system or the Smart Hybrid system.You should have the system inspected bya Maruti Suzuki authorised workshop.

For details, refer to “ENG A-STOP System(Engine Auto Stop Start System)” and“Smart Hybrid” in “OPERATING YOURVEHICLE” section.

2-54

BEFORE DRIVING

72SM0-74E

Master Warning Indicator Light

80P0382


When the information display shows warn-ing and indicator messages, this indicatorlight may also blink.

For details, refer to “Information display” inthis section.

Lighting Control Lever

65D611S

Lighting Operation

73R0056

To turn the lights on or off, twist the knobon the end of the lever. There are threepositions:

OFF (1)All lights are off.

(2)Front position lights, tail lights, licenseplate light and instrument lights are on, butheadlights are off.

(3)Front position lights, tail lights, licenseplate light, instrument lights and headlightsare on.

WARNING

To avoid possible injury, do not oper-ate controls by reaching through thesteering wheel.

EXAMPLE

(3)

(2)(1)

EXAMPLE

2-55

BEFORE DRIVING

72SM0-74E

73R0057

With the headlights on, push the lever for-ward to switch to the high beams (mainbeams) or pull the lever toward you toswitch to the low beams. When the highbeams (main beams) are on, a light on theinstrument cluster will come on. Tomomentarily activate the high beams (mainbeams) as a passing signal, pull the leverslightly toward you and release it when youhave completed the signal.

Automatic Lights Operation (If equipped)

68PH00252

68PH00253

Your vehicle’s lighting system is controlledby two main systems: the Lighting switchand the Auto-On Headlight System (Whenthe lighting switch is in the “AUTO” posi-tion).The two systems work together to operateyour lights as shown in the following chart:

EXAMPLE

(1)(2)

(3) (4)EXAMPLE

(5)

EXAMPLE

2-56

BEFORE DRIVING

72SM0-74E

ON: Lights ONLIGHT: When it is light around the light sensor (5).DARK: When it is dark around the light sensor (5).

Lighting switch posi-tion

Main lights to be operated

Ignition mode “LOCK” (OFF)

or “ACC”Ignition mode “ON”

LIGHT DARK LIGHT DARK

(1) OFFPosition lights, Tail lights – – – –

Headlights – – – –

(2) AUTOPosition lights, Tail lights – – – ON

Headlights – – – ON

(3) Position lights, Tail lights ON ON ON ON

Headlights – – – –

(4) Position lights, Tail lights ON ON ON ON

Headlights ON ON ON ON

To turn the lights on or off, twist the knobon the end of the lever. There are fourpositions:

OFF (1)All lights are off.

AUTO (2)This function works when the ignitionmode has been changed to “ON” by press-ing the engine switch. The headlights andposition lights are turned on and off auto-matically according to the amount of out-side light detected by a sensor. They goout automatically when you change theignition mode to “ACC” or “LOCK” bypressing the engine switch.

The light sensor (5) for sensing the amountof outside light is installed on the passen-ger’s seat side instrument panel.

CAUTION

If the light sensor area of the wind-shield is covered with mud, ice, orother similar substances, the head-lights and position lights may beturned on even when it is still lightoutside.

2-57

BEFORE DRIVING

72SM0-74E

NOTE:• Avoid covering the light sensor area of

the windshield with a sticker. The stickermay impair the performance of the sen-sor and make the system unable to con-trol operation of the lights correctly.

• If you changed the ignition mode to “ON”by pressing the engine switch and the“AUTO” position remains selected, theheadlights and position lights come onautomatically as the outside gets darkeven with the engine not running. Leav-ing the lights lit for a long time may leadto a completely discharged battery.

(3)Front position lights, tail lights, licenseplate light and instrument lights are on, butheadlights are off.

(4)Front position lights, tail lights, licenseplate light, instrument lights and headlightsare on.

68PH00254

With the headlights on, push the lever for-ward to switch to the high beams (Mainbeams) or pull the lever toward you toswitch to the low beams. When the highbeams (Main beams) are on, a light on theinstrument panel will come on. To momen-tarily activate the high beams (Mainbeams) as a passing signal, pull the leverslightly toward you and release it when youhave completed the signal.

Auto-on headlight system

68PH00253

The Auto-on headlight system automati-cally turns on all lights that are operated bythe lighting control lever on the steeringcolumn, when the following three condi-tions are all met.

Conditions for Auto-on headlight systemoperation:1) It is dark around the light sensor (5).2) The lighting control lever is in the

“AUTO” position.3) You press the engine switch to change

the ignition mode to “ON”.

This system is operated by a signal fromthe light sensor (5) on the passenger’sseat side Instrument panel. Do not coverthe sensor (5). If you do, the system willnot work correctly.

EXAMPLE

(5)

EXAMPLE

2-58

BEFORE DRIVING

72SM0-74E

NOTE:The light sensor reacts even to infraredrays, so it may operate incorrectly whenthere are strong infrared rays.

Light Reminder BuzzerThe interior buzzer continuously beeps ifyou open the driver’s door without turningoff the headlights and position lights. Thisfunction is triggered under the followingcondition: The headlights and/or position lights areon even after the engine switch is pressedto change the ignition mode to “LOCK”(OFF).

The buzzer stops sounding when you turnoff the headlights and position lights.

Daytime Running Light (D.R.L.) SystemWhen the engine is started, this systemturns on the daytime running lights.

Conditions for D.R.L. system operation 1) The engine is running.2) Headlights and front fog light are off.

NOTE:Brightness of the daytime running lights isdifferent from the brightness of the positionlights, but it is not a malfunction.

Guide Me Light (Vehicle with auto-matic lights operation)

Follow me home functionThis function turns on the front positionlights and the headlights in the low beamsetting for about 10, 15, 20, 25 or 30 sec-onds after the engine switch is pressed tochange the ignition mode to “LOCK”(OFF).

To set the function:1) Turn the lighting switch to the “AUTO”

position2) Press the engine switch to change the

ignition mode to “LOCK” (OFF). 3) Pull the lighting control lever toward

you once and open the driver’s sidedoor within 60 seconds. Or pull thelighting control lever toward you oncewhile the driver’s side door is open.

To cancel the function:Perform any of the following operations. • Pull the lighting control lever toward you

once.• Change the ignition mode to “ACC” or

“ON” by pressing the engine switch.• Turn the lighting switch to any other

position than the “AUTO” position.

NOTE:• When the “follow me home” is function-

ing, the front fog lights and the head-lights (High beam) are not turned on.

• Lighting time of the “follow me homefunction” can be changed on the infor-mation display. Refer to “Information Dis-play” in this section.

Lead to vehicle functionIf the “UNLOCK” button of the remote con-troller is pressed while the lighting switch ispositioned in the “AUTO”, the front positionlights and the headlights in the low beamare turned on for 10, 15, 20 or 25 seconds.The lead to vehicle function will operateonly when it is dark outside the vehicle.

To cancel the function:Perform any of the following operations.• Lock the doors by using the remote con-

troller or request switch, or the key in thedriver’s door lock.

• Change the ignition mode to “ACC” or“ON” by pressing the engine switch.

• Turn the lighting switch to any otherposition than the “AUTO” position.

WARNING

It takes about 5 seconds for the lightsensor to react to a change in light-ing conditions. To help avoid an acci-dent due to reduced visibility, turn onyour headlights before driving into atunnel, parking structure or the like.

2-59

BEFORE DRIVING

72SM0-74E

NOTE:• When the “lead to vehicle” is functioning,

the front fog lights and the headlights(high beam) are not turned on.

• Lighting time of the “lead to vehicle func-tion” can be changed on the informationdisplay. Refer to “Information Display” inthis section.

Front Fog Light Switch

73R0058

To turn the front fog light on, twist the knobas shown in the illustration with the posi-tion lights, tail lights and/or the headlightsare on. When the front fog light is on, anindicator light on the instrument cluster willcome on.

Headlight Leveling Switch

75RM008

Level the headlight beam according to theload condition of your vehicle by turningthis switch. The chart shows the appropri-ate switch position for different vehicle-load conditions.

EXAMPLE EXAMPLE

2-60

BEFORE DRIVING

72SM0-74E

Turn Signal Control Lever

65D611S

Turn Signal OperationWith the ignition mode “ON”, move thelever upward or downward to activate theright or left turn signals.

Normal turn signal

73R0059

Move the lever all the way upward ordownward to signal. When the turn is com-pleted, the signal will cancel and the leverwill return to its normal position.

Loading Conditions Switch Position

Driver (1 Seat) 0

Driver + Co-Driver (2 Seats) 0

Driver + Co-Driver + 2ndrow 2 Seats (Total-4 Seats)

1

All Passengers (6 Seats) 1.5

All Passengers + Cargo(Evenly distributed load inluggage boot)

2.5

Driver + Cargo (Evenlydistributed load in lug-gage boot)

4 WARNING


EXAMPLE

EXAMPLE

2-61

BEFORE DRIVING

72SM0-74E

Lane change signal

73R0060

Move the lever partially upward or down-ward to turn right or left and hold the leverin the moved position.• The turn signal and its indicator flash

while the lever is held at the moved posi-tion.

• The turn signal and its indicator flash 3times even if you returned the leverimmediately after the activation.

NOTE:The turn signal and its indicator can be setwhether they flash 3 times after the turnsignal lever is returned via the informationdisplay. Refer to “Information display” inthis section.

Hazard Warning Switch

73R0011

Push the hazard warning switch to activatethe hazard warning lights. All turn signallights and both turn signal indicators willflash simultaneously. To turn off the lights,push the switch again.Use the hazard warning lights to warnother drivers of possible risk of traffic haz-ard when you park your vehicle in case ofemergency.

Windshield Wiper and Washer Lever

65D611S

EXAMPLEEXAMPLE

WARNING


EXAMPLE

2-62

BEFORE DRIVING

72SM0-74E

Wiper and Washer OperationWhen the ignition mode is “ON”, you canuse the wiper/washer lever or switch.

When the wipers are under heavy loadsuch as covered by snow, the breaker willbe activated and the wipers will stop oper-ating to protect the wiper motor from over-heating.

If the wiper stops during operation, do thefollowing methods.

1) Stop the vehicle in a safe place, andturn the engine off.

2) Move the wiper lever and switch to“OFF” position.

3) Remove obstacles such as snow on thewipers.

4) After a while, when the temperature ofthe wiper motor becomes low enough,the breaker will be reset automaticallyand the wipers will be able to use.

If you cannot use the wipers after a while,there may be another problem. Ask aMaruti Suzuki authorised workshop tohave the wipers inspected.

Windshield Wipers

72R0126

To turn the windshield wipers on, move thelever down to one of the three operatingpositions. In “INT” position, the wipersoperate intermittently. “INT” position is veryconvenient for driving in mist or light rain.In “LO” position, the wipers operate at asteady low speed. In “HI” position, the wip-ers operate at a steady high speed. To turnoff the wipers, move the lever back to“OFF” position.

Move the lever up and hold it to “MIST”position, the windshield wipers will turn oncontinuously at low speed.

Windshield Washer

72R0127

To spray windshield washer fluid, pull thelever toward you. The windshield wiperswill automatically turn on at low speed ifthey are not already on and “INT” positionis equipped.

MIST

HI

OFF

LO

INT

EXAMPLE

WARNING

• To prevent windshield icing in coldweather, turn on the defroster toheat the windshield before andduring windshield washer use.

• Do not use radiator antifreeze solu-tion in the windshield washer res-ervoir. This can severely impairvisibility when sprayed on thewindshield, and also damage yourvehicle’s paint.

EXAMPLE

2-63

BEFORE DRIVING

72SM0-74E

Rear Window Wiper/Washer Switch

72R0128

To turn the rear wiper on, twist the rearwiper switch on the end of the lever for-ward to “ON” position. To turn the rearwiper off, twist the switch rearward to“OFF” position.

To spray window washer fluid, twist theswitch rearward from “OFF” position, ortwist the switch forward from “ON” position.The rear wiper will turn on automaticallywhile spraying the window washer fluid.

Tilt Steering Lock Lever

73R0012

(1) LOCK(2) UNLOCK

The lock lever is located under the steeringcolumn. To adjust the steering wheelheight:

1) Push down the lock lever to unlock thesteering column.

2) Adjust the steering wheel to the desiredheight and lock the steering column bypulling up the lock lever.

3) Try moving the steering wheel up anddown to make sure it is securely lockedin position.

NOTICE

To help prevent damage to the wind-shield wiper and washer systemcomponents, you should take the fol-lowing precautions:• Do not continue to hold in the lever

when there is no windshieldwasher fluid being sprayed or thewasher motor can be damaged.

• Do not attempt to remove dirt froma dry windshield with the wipers oryou can damage the windshieldand the wiper blades. Always wetthe windshield with washer fluidbefore operating the wipers.

• Clear ice or packed snow from thewiper blades before using the wip-ers.

• Check the washer fluid level regu-larly. Check it often when theweather is bad.

• Only fill the washer fluid reservoir3/4 full during cold weather to allowroom for expansion if the tempera-ture falls low enough to freeze thesolution.

NOTICE

Clear ice or snow from the rear win-dow and rear wiper blade beforeusing the rear wiper. Accumulatedice or snow could prevent the wiperblade from moving, causing damageto the wiper motor.

Washer

Wiper

EXAMPLE

WARNING

Never attempt to adjust the steeringwheel while the vehicle is moving oryou could lose control of the vehicle.

(1)

(2)

EXAMPLE

2-64

BEFORE DRIVING

72SM0-74E

Horn

73R0062

Press the horn button of the steering wheelto sound the horn. The horn will sound inany ignition mode.

Heated Rear Window Switch

72R0043

When the rear window is misted, push thisswitch (1) to clear the window.

An indicator light will come on when thedefogger is on. The defogger will work onlywhen the engine is running. To turn off thedefogger, push the switch (1) again.

NOTE:• The defogger will work only when the

engine is running.• The defogger will automatically turn off

after the defogger remains on for 15 min-utes to prevent discharging of the lead-acid battery.

EXAMPLE

NOTICE

The heated rear window use a largeamount of electricity. Turn off theswitch after the window have becomeclear.

(1)

EXAMPLE

2-65

BEFORE DRIVING

72SM0-74E

Vehicle LoadingYour vehicle was designed for specificweight capacities. The weight capacities ofyour vehicle are indicated by the GrossVehicle Weight Rating (GVWR) and thePermissible maximum Axle Weight (PAW,front and rear). The GVWR and PAW (frontand rear) are listed in “SPECIFICATIONS”section.

GVWR – Maximum permissible overallweight of the fully loaded vehicle (includingall the occupants, accessories and cargoplus the trailer nose weight if towing atrailer).PAW – (Front and Rear) Maximum permis-sible weight on an individual axle.

Actual weight of the loaded vehicle andactual loads at the front and rear axles canonly be determined by weighing the vehi-cle. Compare these weights to the GVWRand PAW (front and rear). If the gross vehi-cle weight or the load on either axleexceeds these ratings, you must removeenough weight to bring the load down tothe rated capacity.

Trailer Towing your vehicleYour MARUTI SUZUKI was originallydesigned to carry people and a normalamount of cargo, not to tow a trailer.

WARNING

Never overload your vehicle. Thegross vehicle weight (sum of theweights of the vehicle, all the occu-pants, accessories, cargo plus trailernose weight if towing a trailer) mustnever exceed the Gross VehicleWeight Rating (GVWR). In addition,never distribute a load so that theweight on either the front or rear axleexceeds the Permissible maximumAxle Weight (PAW).

WARNING

Always distribute cargo evenly. Toavoid personal injury or damage toyour vehicle, always secure cargo toprevent it from shifting if the vehiclemoves suddenly. Place heavierobjects on the floor and as far for-ward in the cargo area as possible.Never pile cargo higher than the topof the seat backs.

OPERATING YOUR VEHICLE

3

72SM0-74E

60G408

OPERATING YOUR VEHICLEDaily Inspection Checklist .................................................. 3-1Engine Oil Consumption .................................................... 3-2Engine Switch....................................................................... 3-2Keyless Push Start System ................................................ 3-3Parking Brake Lever ........................................................... 3-7Pedal ..................................................................................... 3-8Starting the Engine .............................................................. 3-9Using the Transmission ..................................................... 3-12Gearshift Indicator (if equipped) ........................................ 3-16Smart Hybrid ........................................................................ 3-17ENG A-STOP System (Engine Auto Stop Start System) ....................................... 3-19Cruise Control ..................................................................... 3-25Parking Sensors .................................................................. 3-28Rearview Camera (if equipped) .......................................... 3-32Braking.................................................................................. 3-35Electronic stability program (ESP®) (if equipped) ............ 3-38

3-1


72SM0-74E

Daily Inspection Checklist

Before Driving

72SM03003

1) Make sure that windows, mirrors, lightsand reflectors are clean and unob-structed.

2) Visually check the tires for the followingpoints:

– the depth of the tread groove– abnormal wear, cracks and damage– loose wheel nuts– existence of foreign material such as

nails, stones, etc.

Refer to “Tires” in “INSPECTION ANDMAINTENANCE” section for details.3) Look for fluid and oil leakage.

NOTE:It is normal for water to drip from the airconditioning system while and after use.

4) Make sure the hood is fully closed andlatched.

5) Check the headlights, turn signal lights,brake lights and horn for proper opera-tion.

6) Adjust the seat and head restraint. 7) Check the brake pedal and the parking

brake lever.8) Adjust the mirrors.9) Make sure that you and all passengers

have properly fastened the seat belts.10)Make sure that all warning lights come

on as the ignition is pushed to “ON”.11)Check all gauges.12)Make sure that the BRAKE SYSTEM

WARNING light turns off when the park-ing brake is released.

Once a week, or each time you fill your fueltank, perform the following under-hoodchecks:

1) Engine oil level2) Coolant level3) Brake fluid level4) Battery fluid (acid) level5) Windshield washer fluid level6) Hood latch operation

Pull the hood release handle inside thevehicle. Make sure that you cannotopen the hood all the way withoutreleasing the secondary latch. Be sureto close the hood securely after check-

ing for proper latch operation. See theitem “All latches, hinges and locks” of“CHASSIS AND BODY” in “PeriodicMaintenance Schedule” in “INSPEC-TION AND MAINTENANCE” section forlubrication schedule.

Once a month, or each time you fill yourfuel tank, check the tire pressure using atire pressure gauge. Also check the tirepressure of the spare tire.

EXAMPLE

WARNING

Make sure the hood is fully closedand latched before driving. If it is not,it can fly up unexpectedly duringdriving, obstructing your view andresulting in an accident.

3-2


72SM0-74E

Engine Oil ConsumptionIt is normal for the engine to consumesome engine oil during normal vehicleoperation.The amount of engine oil consumptiondepends on viscosity and quality of the oiland your driving conditions. More oil is consumed during high-speeddriving and when there is frequent acceler-ation and deceleration. Under high loads,your engine also will consume more oil.A new engine also consumes more oil,since its pistons, piston rings and cylinderwalls have not yet become conditioned.New engines reach the normal level of oilconsumption only after approximately5000 km driving.

Oil consumption: Max. 1.0 L per 1000 kmWhen judging the amount of oil consump-tion, note that the oil may become dilutedand it is difficult to judge the accurate oillevel. As an example, if a vehicle is used forrepeated short trips, and consumes a nor-mal amount of oil, the dipstick may notshow any drop in the oil level at all, evenafter 1000 km or more of driving. This isbecause the oil is gradually becomingdiluted with fuel or moisture, making itappear that the oil level has not changed.You should also be aware that the dilutingingredients evaporate out when the vehicleis subsequently driven at high speeds,such as on an expressway, making itappear that oil is excessively consumedafter high-speed driving.

Engine Switch

73R0063

LOCK (OFF)This mode is for parking the vehicle. Whenthis mode is selected by pressing theengine switch and then any door (includingthe tailgate) is opened or closed, the steer-ing will be locked automatically.

ACCPress the engine switch to select this igni-tion mode to use such electric equipmentas the audio system, outside rearview mir-rors and accessory socket with the engineoff. When this position is selected, the“ACC” indicator light in the instrument clus-ter comes on. Refer to “Warning and Indi-cator Lights” in “BEFORE DRIVING”section for details.

EXAMPLE

3-3


72SM0-74E

ON• With the engine off

You can use such electric equipment asthe power windows and wipers with theengine off. When this ignition mode isselected by pressing the engine switch,the Ignition “ON” indicator light in theinstrument cluster will come on.

• With the engine onAll electric equipment is operational. Thevehicle can be driven when you haveselected this ignition mode by pressingthe engine switch.

STARTManual transmission – Provided you havethe keyless push start system remote con-troller with you, the engine automaticallystarts when you press the engine switch toselect this ignition mode after shifting to“N” (Neutral) and depressing the brake andclutch pedals.

Automatic transmission – Provided youhave the keyless push start system remotecontroller with you, the engine automati-cally starts when you press the engineswitch to select this ignition mode afterplacing the gearshift lever in P position anddepressing the brake pedal. (If you need tore-start the engine while the vehicle ismoving, shift into “N”.)

NOTE:You do not need to keep the engine switchpressed to start the engine.

NOTE:• The steering lock may not be released

and the immobilizer/ keyless push startsystem warning light turns on if someload is applied on the steering wheel. Ifthis happens, turn the steering wheel tothe right or left to relieve it from the loadbefore you press the engine switchagain to change to the desired ignitionmode.

• In the presence of strong radio wave ornoise, you may not be able to changethe ignition mode to “ACC” or “ON” or tostart the engine using the engine switch.

Keyless Push Start System Provided the keyless push start systemremote controller is within the interior work-able area (refer to the related explanationin this section), you can use the engineswitch for starting the engine and selectingan ignition mode (“ACC” or “ON”). In addi-tion, the following functions can be used:

• Keyless entry function. Refer to “Keylesspush start system remote controller” in“BEFORE DRIVING” section for details.

• Locking and unlocking doors (includingthe tailgate) using a request switch.Refer to “Keyless push start systemremote controller” in “BEFORE DRIV-ING” section for details.

• Immobilizer (anti-theft) function. Refer to“Immobilizer System” in “BEFOREDRIVING” section for details.

Engine Switch IlluminationThe engine switch is illuminated (lit) in thefollowing situations:• When the engine is off and the driver’s

door is open, or for 15 seconds after thedriver’s door is closed. The illuminationwill fade out after 15 seconds passed.

• When the engine is off and the positionlights are on. The illumination will go outwhen the position lights are turned off.

• When the engine is on and the positionlights and/or the headlights are on. Theillumination will go out when the positionlights and the headlights are turned off.

NOTICE

Do not leave the engine switch in“ACC” or “ON” mode when theengine is not running. Avoid usingthe radio or other electric accesso-ries for a long time when the engineswitch is in the “ACC” or “ON” modewhen the engine is not running, oth-erwise the lead-acid battery may dis-charge.

3-4


72SM0-74E

82K253

NOTE:To save the lead-acid battery, the illumina-tion will be automatically turned off whenboth of the following conditions are simul-taneously met:• The headlights and position lights are

turned off.• 15 minutes has elapsed since opening

the driver’s door.

Selection of Ignition ModesPress the engine switch to select “ACC” or“ON” mode as follows when you use anelectric accessory or check the operationof instruments without running the engine.

1) Bring the keyless push start systemremote controller with you and sit in thedriver’s seat.

2) Manual transmission – Withoutdepressing the clutch pedal, press theengine switch (1).Automatic transmission – Withoutdepressing the brake pedal, press theengine switch (1).

82K254

Every time you press the engine switch,the ignition mode changes as follows.

Manual Transmission

68PH00322

Automatic Transmission

57L31006

EXAMPLE

(1)

EXAMPLE

EXAMPLE

(OFF) (Audio equipment)

P

P

(OFF)

ONACCLOCK(Audio equipment)

Gearshift lever in a position other than

Gearshift lever in

EXAMPLE

3-5


72SM0-74E

NOTE:• Automatic transmission – If the gearshift

lever is in any position other than “P”, orif the knob button is pushed when thegearshift lever is in P position, the igni-tion mode cannot be returned to “LOCK”(OFF).

If the “PUSH” indication comes on ininformation display and the ignitionmodes cannot be selectedYour keyless push start system remote con-troller may not be sensed as being within the“interior workable area” (refer to the relatedexplanation in this section). Try again aftermaking sure you have the remote controllerwith you. If the ignition modes still cannot beselected, the battery of the remote controllermay be discharged. To be able to select anignition mode, you must then use the follow-ing method:

52RM30020

1) Without depressing the brake pedaland the clutch pedal, push the engineswitch (1).

2) Within about 10 seconds during whichthe “PUSH” indicator light in the instru-ment cluster is blinking, touch theengine switch with the LOCK buttonend of the remote controller (2) forabout 2 seconds.

NOTE:• If you still cannot select the ignition

modes, there may be some problemswith the keyless push start system. Con-tact a Maruti Suzuki authorised work-shop for an inspection of the system.

• The immobilizer/keyless push start sys-tem warning light come on for about 5seconds while the “PUSH” indicator lightis blinking. Refer to “Warning and Indica-tor Lights” in “BEFORE DRIVING” sec-tion for details.

• You may customize the system to causethe interior buzzer to sound once for the“remote controller out of sensing range”warning. To incorporate this customiza-tion, please contact a Maruti Suzukiauthorised workshop.

• If the battery of the remote controller isabout to become completely discharged,the keyless push start system remote con-troller battery consumption warning light inthe instrument cluster will come on for afew seconds when you press the engineswitch to change the ignition mode to“ON”. Refer to “Keyless Push Start System

Remote Controller Battery ConsumptionWarning Light” in “Keyless Push Start Sys-tem Remote Controller” in “BEFOREDRIVING” section for details. For detailson replacing the battery, refer to “KeylessPush Start System Remote Controller” in“BEFORE DRIVING” section.

“Remote Controller Outside” Warn-ingWhen either of the conditions describedbelow is met, the system causes a“Remote Controller Outside” warning bysounding the interior and exterior buzzers.At the same time, the immobilizer/keylesspush start system warning light blinks.

• Any door is opened and then closed whilethe remote controller is not inside the vehi-cle and the engine is running or the ignitionmode has been changed to “ACC” or “ON”by pressing the engine switch.

• The remote controller is not inside thevehicle when you attempt to start theengine after changing the ignition modeto “ACC” or “ON” by pressing the engineswitch.

(1)

(2)

EXAMPLE

3-6


72SM0-74E

72SM03001

(1) Immobilizer/keyless push start sys-tem warning light (blinks)

NOTE:• If the warning is given, relocate the

remote controller as soon as possible.• Any attempt to start the engine will fail

while the warning is active. Blinking ofthe immobilizer/keyless push start sys-tem warning light in the instrument clus-ter will indicate this condition. Refer to“Warning and Indicator Lights” in“BEFORE DRIVING” section for details.

• Blinking of the immobilizer/keyless pushstart system warning light should stopshortly after the remote controller isbrought back inside the vehicle. If theimmobilizer/keyless push start systemwarning light does not stop blinking,change the ignition mode to “LOCK”(OFF) by pressing the engine switch and

then perform the engine starting opera-tion.

• Always keep the remote controller withyou as the driver.

Interior Workable Area for Engine Starting, Ignition Mode Selection and “Remote Controller Outside” Warning

73R0198

(1) Interior workable area

The “interior workable area” for these func-tions is defined as all the interior spacesexcept for the space above the instrumentpanel.

NOTE:• Even when the remote controller is in the

“interior workable area”, if it is in any ofthe following conditions, you may not beable to start the engine or select the igni-

tion modes, and the “remote controlleroutside” warning may be given.–The remote controller’s battery is low.–The remote controller is affected by

strong radio signals or noise.–The remote controller is in contact with

or covered by a metallic object.–The remote controller is in stowage like

the glove box or a door pocket.–The remote controller is in the sun visor

pocket or on the floor.• Even when the remote controller is out-

side the “interior workable area”, if it is inany of the following conditions, you maybe able to start the engine or select theignition mode. The “remote controlleroutside” warning may not be given atthat time.–The remote controller is outside the

vehicle but very close to a door.–The remote controller is on the instru-

ment panel.

(1)

EXAMPLE

(1)

EXAMPLE

3-7


72SM0-74E

Parking Brake Lever

60MHM03001

(1) To set(2) To release(3) To release

The parking brake lever is located betweenthe front seats. To set the parking brake,depress the brake pedal and pull the park-ing brake lever all the way up. To releasethe parking brake, depress the brake pedaland pull up slightly on the parking brakelever, push the button on the end of thelever with your thumb, and lower the leverto its original position.

For automatic transmission vehicles,always set the parking brake before mov-ing the gearshift lever to P (PARK) posi-tion. If you park on an incline and shift into“P” before setting the parking brake, theweight of the vehicle may make it difficult

to shift out of “P” when you are ready todrive the vehicle.

When preparing to drive the vehicle, movethe gearshift lever out of P position beforereleasing the parking brake.

(1)

(2)

(3)

EXAMPLE

WARNING

• Never drive your vehicle with theparking brake on: rear brake effec-tiveness can be reduced from over-heating, brake life may beshortened, or permanent brakedamage may result.

• If the parking brake does not holdthe vehicle securely or does notfully release, have your vehicleinspected immediately by a MarutiSuzuki authorised workshop.

• When parking on an uphill, turn thesteering wheel so that the frontwheels point to the center of theroad.

• When parking on a downhill, turnthe steering wheel so that the frontwheels point to the curb.

WARNING

Whenever parking, make sure thegearshift lever for manual transmis-sion vehicles is in 1st gear or “R”(Reverse) and the gearshift lever forautomatic transmission vehicles is in“P” (Park). Remember, even thoughthe transmission is in gear or in Park,you must set the parking brake fully.

WARNING

When parking the vehicle inextremely cold weather, the followingprocedure should be used:1) Set the parking brake.2) Manual Transmission - turn off the

engine, then shift into reverse orfirst gear.Automatic Transmission - shiftinto “P” (Park) and turn off theengine.

3) Get out of the vehicle and putchocks under the wheels.

4) Release the parking brake. When you return to your vehicle,you must remember to first set theparking brake, then remove thewheel chocks.

3-8


72SM0-74E

Parking Brake Reminder BuzzerA buzzer sounds intermittently to remindyou to release the parking brake if youstart the vehicle without fully releasing theparking brake. Make sure that the parkingbrake is fully released and the brake sys-tem warning light turns off.

Pedal

Manual Transmission

80J2121

Automatic Transmission

80J2122

Clutch Pedal (1)(for manual transmission)A clutch pedal is used to disengage thedriving force to the wheels when startingthe engine, stopping, or shifting the gear-shift lever. Depressing the pedal disen-gages the clutch.

Brake Pedal (2)Your vehicle is equipped with front discbrakes and rear drum brakes. Depressingthe brake pedal applies both sets ofbrakes.

You may hear occasional brake squealwhen you apply the brakes. This is a nor-mal condition caused by environmentalfactors such as temperature, humidity ordust, etc.Automatic transmission – You may hearoccasional sound when you release brakepedal while vehicle is in “D” (Drive) modeand about to move. This is a normal phe-nomenon.

WARNING

Do not leave cigarette lighters, spraycans, soft drink cans or plastic arti-cles (such as glasses, CD cases, etc.)in sun-heated vehicle. The tempera-ture inside the vehicle may cause asfollows:• Gas may leak from a cigarette

lighter or spray can and may leadto a fire.

• The glasses, plastic cards or CDcases, etc. may deform or crack.

• Soft drink cans may fracture.

(2)(1)

(3)

EXAMPLE

(3)

(2)

EXAMPLE

WARNING

Do not drive with your foot resting onthe clutch pedal. It could result inexcessive clutch wear, clutch dam-age, or unexpected loss of enginebraking.

3-9


72SM0-74E

Accelerator Pedal (3)An accelerator pedal controls the speed ofthe engine. Depressing the acceleratorpedal increases power output and speed.

Starting the Engine

Before Starting the Engine

72RM03002

1) Make sure the parking brake is set fully.2) Manual transmission – Shift to “N”

(Neutral) and fully depress the clutchpedal. Hold the clutch and brake pedalsfully depressed.Automatic transmission – If the gear-shift lever is not in the P (Park) position,shift it to “P”. Hold the brake pedal fullydepressed.

82K254

3) The “PUSH START SWITCH” indica-tion appears in the information display.Push the engine switch (1). When theengine is started, the starter motor willautomatically stop.

WARNING

If brake squeal is excessive andoccurs each time the brakes areapplied, you should have the brakeschecked by a Maruti Suzuki autho-rised workshop.

WARNING

Do not apply brakes continuously orrest your foot on the brake pedal.This will result in overheating of thebrakes which could cause unpredict-able braking action, longer stoppingdistances, or permanent brake dam-age.

MT

AT

EXAMPLE

WARNING

Make sure that the parking brake isset fully and the transmission is inNeutral (or Park for vehicles with anautomatic transmission) beforeattempting to start the engine.

(1)

EXAMPLE

3-10


72SM0-74E

NOTE:• You do not need to keep the engine

switch pressed to start the engine.• The engine of a manual transmission

vehicle will not start unless the clutchpedal is depressed.

• Automatic transmission vehicles have astarter interlock device which isdesigned to keep the starter from operat-ing if the transmission is in any of thedrive positions.

• You should turn off such loads as theheadlights and air conditioning system tofacilitate starting of the engine.

• Even if you fail to start the engine, thestarter motor will stop turning automati-cally after a short time. After the startermotor has stopped or if there is someproblem with the system, the starter

motor will rotate only while the engineswitch is being pressed.

Stopping the Engine• Depress the engine switch to stop the

engine after the vehicle stopped com-pletely.

• In case of emergency, you can stop theengine by quickly pushing the engineswitch more than 3 times, or pushingand holding the engine switch for morethan 2 seconds while the vehicle inmotion.

NOTE:Except in cases of emergency, do not stopthe engine while the vehicle is in motion.The steering and braking operation willrequire more effort when the engine isstopped.Refer to “Braking” in this section.

• If the engine remains stopped for whileafter it was stopped unexpectedly or wasraced before stopping, a clicking soundmay be heard from around the enginewhen it is restarted. This is not a mal-

function. Always let the engine idlebefore stopping it.

Starting a Cold and Warm EngineWith your foot taken off the acceleratorpedal, crank the engine by pressing theengine switch to change the ignition modeto “START”.

After pressing the engine switch to changethe ignition mode to “START”, the startercranks the engine for about 12 secondsbefore it can start the engine. If the enginefails to start at the first attempt, wait 15seconds, and then try again while keepingthe engine switch pressed while pressingdown the accelerator pedal to 1/3 of itsstroke. Release the accelerator pedalwhen the engine starts.

If the engine still does not start, try holdingthe accelerator pedal all the way to thefloor while cranking. If you are unable to start the engine usingthis procedure, consult a Maruti Suzukiauthorised workshop.

NOTICE

• Do not depress the acceleratorduring the engine starting proce-dure.

• If the engine does not respondwhen you try to start it with theengine switch or if the engineswitch repeats cycling through“LOCK”(OFF) - “ACC” - “ON”mode, the lead-acid battery may bedischarged. Check the voltage ofthe lead-acid battery before tryingagain.

NOTICE

If you stop the engine while the vehi-cle is in motion, the automatic trans-mission may be damaged.Avoid stopping the engine while driv-ing.

NOTICE

Do not crank the engine for morethan 12 seconds at a time. If the engine does not start on thefirst try, wait 15 seconds before try-ing again.

3-11


72SM0-74E

If the “PUSH” indication comes on andthe engine cannot be startedYour keyless push start system remotecontroller may not be sensed as beingwithin the interior workable area. Try againafter checking that you have the remotecontroller with you. If the engine still can-not be started, the battery of the remotecontroller may be discharged. To start theengine, use the following method:

52RM30020

1) Make sure the parking brake is set fully.2) Manual Transmission – Shift to “N”

(Neutral) and fully depress the clutchpedal. Hold the clutch and brake pedalsfully depressed. Automatic Transmission – If the gear-shift lever is not in the P (Park) position,shift it to “P”. Hold the brake pedal fullydepressed.

3) The “PUSH” indication in the informa-tion display will come on. Press theengine switch (1).

4) Within about 10 seconds of blinking ofthe “PUSH” indicator light in the instru-ment cluster, touch the engine switchwith the LOCK button end of the remotecontroller (2) for about 2 seconds.

NOTE:• If you still cannot start the engine after

several attempts using the abovemethod, there may be a problem else-where, such as a low battery. Contact aMaruti Suzuki authorised workshop forinspection.

• The immobilizer/keyless push start sys-tem warning light will come on for about5 seconds while the “PUSH” indicatorlight is blinking.

• You may customize the system to causethe interior buzzer to sound once forwarning that remote controller is out ofsensing range. Please contact a MarutiSuzuki authorised workshop for the cus-tomization.

• If the battery of the remote controller isabout to become completely discharged,the keyless push start system remotecontroller battery consumption indicationin information display will come on for afew seconds when you press the engineswitch to change the ignition mode to“ON”. For details on replacing the bat-tery, refer to “Keyless Push Start System

Remote Controller” in “BEFORE DRIV-ING” section.

Returning the Ignition Mode to “LOCK” (OFF)Automatic Transmission – To ensuresafety, the ignition mode can be returnedto “LOCK” (OFF) by pressing the engineswitch only when the gearshift lever isplaced in P position without pressing theknob button.

NOTE:In the case of an automatic transmissionmodel, the ignition mode cannot bereturned to “LOCK” (OFF) mode if thegearshift lever is in any other position than“P”.Certain problems like a fault in engine sys-tem may prevent the engine switch fromgoing back to “LOCK” (OFF) mode. If thishappens, have the vehicle inspected by aMaruti Suzuki authorised workshop afterdoing the following:• Lock the doors using the key to prevent

theft. (The request switches and the key-less push start system remote controllercannot be used to lock them.)

• Disconnect the negative cable from thelead-acid battery to prevent discharge.

(1)

(2)

EXAMPLE

3-12


72SM0-74E

“LOCK” (OFF) mode reminder buzzer If the driver’s door is opened withoutreturning the ignition mode to “LOCK”(OFF) by pressing the engine switch, abuzzer sounds to warn you of this state.

• If you open the driver’s door after press-ing the engine switch to change the igni-tion mode to “ACC”, the interior buzzerbeeps intermittently.

• The buzzer will stop sounding if you thenpush the engine switch twice, thus bring-ing it back the ignition mode to “LOCK”(OFF).

NOTE:Whenever you leave the vehicle, makesure you have returned the ignition modeto “LOCK” (OFF) using the engine switchand then lock the doors. Without returningthe ignition mode to “LOCK” (OFF), youcannot use a request switch or keylesspush start system remote controller to lockthe doors.

Steering lock warning buzzerIf the steering lock fails to engage due to afault in the system when the ignition modeis changed to “LOCK” (OFF) by pressingthe engine switch and any door (includingthe tailgate) is opened or closed, the inte-rior buzzer will warn you of this conditionwith repeated short beeps. If this happens,have the vehicle inspected by a MarutiSuzuki authorised workshop.

Using the Transmission

Manual Transmission

73R0014

Starting offTo start off, depress the clutch pedal all theway to the floor and shift into 1st gear.After releasing the parking brake, graduallyrelease the clutch. When you hear achange in the engine’s sound, slowly pressthe accelerator while continuing to gradu-ally release the clutch.

ShiftingAll forward gears are synchronized, whichprovides for quiet and easy shifting.Always depress the clutch pedal all theway to the floor before shifting gears. Keepthe engine speed below the red zone ofthe tachometer.

Downshifting maximum allowablespeeds

*NOTE:You may not accelerate to the maximumallowable speed because of the driving sit-uation and/or the vehicle condition.

WARNING

Do not hang any items on the gear-shift lever and do not use the gear-shift lever as a handrest. Otherwise,it could prevent proper operation ofthe gearshift lever and cause its mal-function, resulting in an accident.

EXAMPLE

Downshifting km/h

2nd to 1st 20

3rd to 2nd 80

4th to 3rd 115

5th to 4th 155*

NOTICE

Do not downshift to a lower gear atthe speed faster than the maximumallowable speeds for the next lowerspeed, or severe damage to engineand transmission can result.

3-13


72SM0-74E

If it is difficult to engage reverse gear “R”,follow below procedure:-1) Put gear lever in neutral “N”.2) Release the clutch pedal once.Again depress the clutch pedal, and shiftfrom “N” to “R”.

4-Speed Automatic Transmission

73R0068

(1) Overdrive off switch

73R0072

Overdrive off switchThe transmission is a 4-speed (3-speedplus overdrive) automatic transmission. Byoperating the overdrive off switch, thetransmission can be converted to a 3-speed automatic transmission that will notmove to the overdrive position. To convertthe transmission to the 3-speed mode,push in the overdrive off switch andrelease it.

To return the transmission to the 4-speedmode, push in the overdrive off switchagain.

When the engine switch is pressed tochange the ignition mode to “ACC”, thetransmission in the 3-speed mode is con-verted to the 4-speed mode automatically.

The 3-speed mode is suitable for the fol-lowing driving conditions:

WARNING

• Reduce your speed and downshiftto a lower gear before going downa long or steep hill. A lower gearwill allow the engine to providebraking. Avoid riding the brakes orthey may overheat, resulting inbrake failure.

• When driving on slippery roads,slow down before downshifting.Excessive and/or sudden changesin engine speed may cause loss oftraction, which could cause you tolose control.

NOTICE

Before engaging reverse gear “R”,check that the vehicle is completelystationary and gear lever is in neutral“N” position. After depressing clutchpedal fully, shift to “R”.

NOTICE

• To help avoid clutch damage, donot use the clutch pedal as a foot-rest while driving or use the clutchto keep the vehicle stationary on aslope. Depress the clutch fullywhen shifting.

• When shifting or starting off, do notrace the engine. Racing the enginecan shorten engine life and causenegative effect to smooth shifting.

EXAMPLE

(1)

EXAMPLE

3-14


72SM0-74E

• Driving on hilly, winding roads– You can drive more smoothly with less

frequent gear changing• Going down a steep hill

– Some engine braking is provided

Gearshift lever

73R0069

(1) knob button

The gearshift lever is designed so that itcannot be shifted out of P position unlessthe ignition mode is “ON” and the brakepedal is depressed.

The gearshift lever has a lock mechanismto help prevent accidental shifting. To shiftthe gearshift lever:

NOTE:• Always shift the gearshift lever without

pushing in the knob button (1) exceptwhen you shift from “P” to “R”, from “D”to “2”, from “2” to “L”, from “N” to “R” orfrom “R” to “P”. If you always push in theknob button (1) when shifting the gear-shift lever, you could shift into “P”, “R”,“2”, or “L” by mistake.

• If driver’s or passenger’s knee hits thegearshift lever while driving, the levercould move and the gear could bechanged unexpectedly.

Use the gearshift lever positions asdescribed below:

P (Park)Use this position to lock the transmissionwhen the vehicle is parked or when start-ing the engine. Shift into Park only whenthe vehicle is completely stationary.

R (Reverse)Use this position to reverse the vehiclefrom stop. Make sure that vehicle is com-pletely stationary before shifting intoReverse.

N (Neutral)Use this position for starting the engine ifthe engine stalls and you need to restart itwhile the vehicle is moving. You may alsoshift into Neutral and depress the brakepedal to hold the vehicle stationary duringidling.

D (Drive)Use this position for all normal driving.

With the gearshift lever in “D” range youcan get an automatic downshift by pressingthe accelerator pedal. The higher the vehi-cle speed is, the more you need to pressthe accelerator pedal to get a downshift.

2 (Low 2)Use this position to provide extra powerwhen climbing hills, or to provide enginebraking when going down hills.

L (Low 1)Use this position to provide maximumpower when climbing steep hills or drivingthrough deep snow or mud, or to providemaximum engine braking when goingdown steep hills.

WARNING

Always depress the brake pedalbefore shifting from “P” (Park) (or“N” (Neutral) if the vehicle is station-ary) to a forward or reverse gear, tohelp prevent the vehicle from movingunexpectedly when you shift.

(1)EXAMPLE

Shift with the knob button (1)pushed in and the brake pedaldepressed.

Shift with the knob button (1)pushed in.

Shift without the knob button (1)pushed in.

3-15


72SM0-74E

NOTE:If you move the gearshift lever to a lowergear while driving faster than the maximumallowable speed for the lower gear, thetransmission will not actually downshiftuntil your speed drops below the maximumspeed for the lower gear.

If You Cannot Shift Automatic Transmission Gearshift Lever Out of “P” (PARK)

73R0070

Vehicles with an automatic transmissionhave an electrically operated park-lock fea-ture. If the vehicle’s lead-acid battery isdischarged, or there is some other electri-cal failure, the automatic transmission can-not be shifted out of Park in the normalway. Jump starting may correct the condi-tion. If not, follow the procedure describedbelow. This procedure will permit shiftingthe transmission out of Park.

1) Be sure the parking brake is firmlyapplied.

2) If the engine is running, stop theengine.

3) Make sure the ignition mode is “ON” or“ACC”.

4) With the release button (1) pushed,push the knob button (2) and shift thegearshift lever to the desired position.

This procedure is for emergency use only.If repeated use of this procedure is neces-sary, or the procedure does not work asdescribed, take the vehicle to a MarutiSuzuki authorised workshop for repair.

NOTICE

• Do not shift the gearshift lever into“R” while moving forward, or thetransmission may be damaged. Ifyou shift into “R” when the vehiclespeed is over 11 km/h, the trans-mission will not shift into reverse.

• Be sure to take the following pre-cautions to help avoid damage tothe automatic transmission:– Make sure that the vehicle is

completely stationary beforeshifting into “P” or “R”.

– Do not shift from “P” or “N” to“R”, “D”, “2”, or “L” when theengine is running above idlespeed.

– Do not rev the engine with thetransmission in a drive position(“R”, “D”, “2”, or “L”) and thefront wheels not moving.

– Do not use the accelerator tohold the vehicle on a hill. Use thevehicle’s brakes.

(2)

(1)

EXAMPLE

3-16


72SM0-74E

Gearshift Indicator (if equipped)

72R0074

When the gearshift lever is in a positionother than “N” (Neutral), the gearshift indi-cator is indicated on the information dis-play when the ignition mode is “ON”.

The electronic control system monitorsdriving condition (such as vehicle speedand/or engine revolution), and it showswhich gear position is optimal for your driv-ing with the indication on the display.

If UP/DOWN arrow is indicated on the dis-play while driving, we recommend you toshift up or down the gear until the arrowdisappears. It is the optimal gear positionfor a driving condition that reduces theover revolution and stress to the engine,and improves fuel consumption.

For details on how to use the transmission,refer to “Using the Transmission” in thissection.

NOTE:• The gearshift indicator is not indicated

when the gear position is in “N” (Neu-tral).

• If you depress the clutch pedal while UP/DOWN arrow is indicated, the indicationwill disappear.

• If you release your foot from the acceler-ator pedal, UP arrow will disappear.

• The indication of gearshift indicator tim-ing may differ depending on the vehiclecondition and/or driving situation even inthe same vehicle speed and engine rev-olution.

EXAMPLE

WARNING

The gearshift indicator is designed toindicate optimal gear position foryour driving, however, a driver willnot be relieved from the duty of careof driving operation or gear changewith this indicator.To drive safe, do not gaze the gear-shift indicator, pay attention to yourdriving situation and shift up or downif necessary.

3-17


72SM0-74E

Example of the gearshift indicator

Indication Description

Lower gear position is selected for the vehicle speed and/orengine revolution. Changing to a higher gear position is recom-mended.• In this case, shifting up to 4th gear position is recommended.

Current gear position is optimal for the vehicle speed and/orengine revolution.• In this case, 3rd gear position is the best.

Higher gear position is selected for the vehicle speed and/orengine revolution. Changing to a lower gear position is recom-mended. • In this case, shifting down to 2nd gear position is recom-

mended.

Smart HybridSmart Hybrid has an Integrated StarterGenerator (ISG) instead of conventionalgenerator to get a better fuel consumption.

Integrated Starter Generator (ISG) is agenerator which incorporated a motorfunction.

The ISG has the following 3 functions.• Deceleration energy regenerating func-

tion• Engine power assist function• Starter motor function

3-18


72SM0-74E

Deceleration Energy Regenerating Function

72RM03003

While decelerating your vehicle, the ISGgenerates electricity without engine power.This reduces engine loads and improvesfuel consumption.

While decelerating your vehicle, decelera-tion energy regenerating function will beactivated when the following conditions aresatisfied.• Gearshift lever is not in “N” (Neutral).• Clutch pedal is not depressed.• Engine speed is more than 950 rpm.• Inside temperature of lead-acid battery

is in normal condition.• Lithium-ion battery is not fully charged

and inside temperature is in normal con-dition etc.

NOTE:The deceleration energy regeneratingfunction may not work depending on vehi-cle conditions.

Engine Power Assist Function

72RM03004

While the vehicle is running, ISG assistsengine power as a motor in the followinglimited condition. This reduces engineloads and improves fuel consumption.

While the vehicle is running with theengine speed at approximately 4000 rpmor less, engine power assist function willbe activated when all of the following con-ditions are satisfied.

• Smart Hybrid system and ENG A-STOPsystem are working properly. (“ENG A-STOP OFF” indicator light is not blink-ing.)

• Clutch pedal is not depressed.

• ESP® (if equipped) is not activated.• Accelerator pedal is excessively

depressed.• Lead-acid battery and lithium-ion bat-

tery are fully charged and each insidetemperature is in normal condition.

• Engine coolant temperature is in normalcondition.

• ISG inside temperature is in normal con-dition.

NOTE:The engine power assist function may notwork depending on vehicle conditions.

Starter Motor Function

72RM03005

After the engine auto stop by the ENG A-STOP system, the engine will be restartedusing a cranking power of the ISG.

EXAMPLE

EXAMPLE

EXAMPLE

3-19


72SM0-74E

The starting with the ISG is quiet com-pared with starting by the conventionalstarter motor.

NOTE:When you restart the engine by pushingthe engine switch, the conventional startermotor is used and you will hear a gearengagement sound.

Lithium-ion Battery Indication

72R0099

The segments in the lithium-ion batteryindicator (1) give an approximate indicationof the charge of the lithium-ion battery. Thenumber of segments that appear in theindication increases or decreases with thecharge of the lithium-ion battery.

NOTE:The indicator gives an approximate indica-tion. The indication may be delayed or dif-fer from the actual charge of the lithium-ionbattery under certain conditions, for exam-ple, when the outside temperature is low.Also, the minimum segment is 1 bar andthe bar will never be 0. Even when 1 bar isshown, the battery level may be close tobe flat.

ENG A-STOP System (Engine Auto Stop Start System) The ENG A-STOP system (engine autostop start system) automatically stops theengine while waiting briefly at a traffic light,etc., and automatically restarts the engineafterward. This system helps reduce emis-sions, improve fuel consumption and lowerengine noise.

This system stops the engine temporarilyunder specific conditions. Before parkingthe vehicle for an extended period of timeor leaving the vehicle, properly apply theparking brake and stop the engine with theengine switch.

Once the specific conditions are met, theengine will stop automatically after thevehicle has stopped. However, the enginewill not be stopped automatically until con-firmation of the system function is finished.

NOTE:You can change the automatic engine stopcondition via the information display. Referto “Information display” in “BEFORE DRIV-ING” section.

EXAMPLE

3-20


72SM0-74E

Lithium-ion Battery

72R0100

(1) Battery (lead-acid battery)(2) Lithium-ion battery

This lithium-ion battery is used exclusivelyfor the vehicle equipped with ENG A-STOP system or Smart Hybrid, andlocated below the front left side seat.• Just like a battery (lead-acid battery), the

lithium-ion battery also discharges grad-ually. To prevent the lithium-ion batteryfrom dying, you must charge the lithium-ion battery by driving continuously for atleast 30 minutes once a month.

• Vehicle should not be left with the igni-tion mode is “ON” or “ACC” for extendedperiods of time.

• Do not add any external electrical load tolithium-ion battery.

• The lithium-ion battery is maintenance-free.

CAUTION

• Do not get out of the vehicle whilethe engine is automatically stoppedby the ENG A-STOP system. Doingso may lead to an accident. – Manual transmission vehicle – If

the driver’s seat belt is unfas-tened or the driver’s door isopened, the engine will restart.

– Automatic transmission vehicle –If the driver’s seat belt is unfas-tened, even if the brake pedal ispressed down, or the driver’sdoor is opened, the engine will berestarted to warn you that theengine was stopped automati-cally by the ENG A-STOP system.

• If the engine does not restart auto-matically after having beenstopped automatically by the ENGA-STOP system, push the engineswitch to start the engine. Trying tomove the vehicle when the enginehas not yet restarted requires astrong force to turn the steeringwheel or depress the brake pedal,potentially leading to an accident.

NOTICE

The vehicle equipped with this sys-tem uses a dedicated high-perfor-mance lead-acid battery thatsupports ENG A-STOP system.Accordingly, observe the instructionslisted below. If these instructions arenot observed, the system may notactuate properly or the lead-acid bat-tery may die prematurely.• When replacing the lead-acid bat-

tery, use a MARUTI SUZUKI genu-ine battery specified in theSpecification.

• Do not draw power from the lead-acid battery terminals for electricalproducts.

(1)

(2)

EXAMPLE

3-21


72SM0-74E

• To replace or dispose of the lithium-ionbattery, consult a Maruti Suzuki autho-rised workshop.

Automatic Stopping/Restarting of the Engine

Manual transmission vehicle1) With the brake pedal depressed, decel-

erate the vehicle.

72R0101

2) After the vehicle has stopped with theclutch pedal depressed and the gear-shift lever shifted to “N”, and thenrelease the clutch pedal, the engine willstop automatically. The ENG A-STOP indicator light(green) (1) will come on. • The ENG A-STOP system will not

stop the engine automatically if all theautomatic engine stop conditions arenot met. For details, refer to the sec-tion, “Automatic engine stop condi-tions”.

• During the automatic engine stop, theengine may shut down, accompanied

by an interior buzzer or restarted, toensure safety.For details, refer to the section,“Points to note during the automaticengine stop”.

NOTE:The ENG A-STOP system will not operateand engine does not stop automaticallyunder the following conditions:• Engine auto stop function will be ready

once the vehicle runs at a speedexceeding 6km/h after restart of theengine.

• The audio and other electrical compo-nent can be used during the automaticengine stop, but the air conditioner willswitch to the fan mode.

• The fan speed will be limited during theautomatic engine stop (only in the autocontrol mode) to keep the cabin air-con-ditioned for a longer time.

WARNING

Wrong handling of the lithium-ionbattery may result in fire, electricshock or system malfunction.Accordingly, observe the instructionslisted below:• Do not dismount or disassemble

the lithium-ion battery.• Do not let the lithium-ion battery

come in contact with water or otherliquids.

• Do not apply strong impact on thelithium-ion battery.

• Do not step on the lithium-ion bat-tery or put articles on the lithium-ion battery.

• Do not disconnect the lithium-ionbattery terminals or draw powerfrom the terminals for electricalproducts.

(1)

EXAMPLE NOTICE

During the automatic engine stop, donot shift the gearshift lever to a posi-tion other than “N” without depress-ing the clutch pedal. If the gear shiftlever is in a position other than “N”,the engine will not restart automati-cally even if the clutch pedal isdepressed.

3-22


72SM0-74E

72R0102

3) Regardless of whether the vehicle hasstopped or not, depressing the clutchpedal will restart the engine and ENGA-STOP indicator light (green) (1) willgo off.

While the engine is stopped automatically,depressing the clutch pedal will restart theengine consuming fuel. Therefore, for fueleconomy, it is recommended to depressthe clutch pedal just before the vehiclestart.• Without depressing the clutch pedal, the

engine may restart automatically if theautomatic engine restart conditions aremet.For details, refer to the section, “Auto-matic engine restart conditions”.

Automatic transmission vehicle1) With the brake pedal depressed, decel-

erate the vehicle.

72R0146

2) While depressing the brake pedal,place the gearshift lever in “D” or “N”position. The ENG A-STOP indicator light(green) (1) will come on. • The ENG A-STOP system will not

stop the engine automatically if all theautomatic engine stop conditions arenot met. For details, refer to the sec-tion, “Automatic engine stop condi-tions”.

• During the automatic engine stop, theengine may shut down, accompaniedby an interior buzzer or restarted, toensure safety.For details, refer to the section,“Points to note during the automaticengine stop”.

NOTE:The ENG A-STOP system will not operateand engine does not stop automaticallyunder the following conditions:• Engine auto stop function will be ready

once the vehicle runs at a speedexceeding 6km/h after restart of theengine.

• The audio and other electrical compo-nent can be used during the automaticengine stop, but the air conditioner willswitch to the fan mode.

• The fan speed will be limited during theautomatic engine stop (only in the autocontrol mode) to keep the cabin air-con-ditioned for a longer time.

72R0147

(1)

EXAMPLE

(1)

EXAMPLE

(1)

EXAMPLE

3-23


72SM0-74E

3) Remove your foot from the brake pedal.“ENG A-STOP” indicator light (green)(1) in the instrument cluster will beturned off and the engine will restartautomatically.

When restarting the engine, keeping brakeforce temporarily prevents the vehicle frommoving forward by the creeping function.Also, this prevents the vehicle from rollingdownward on a hill. For details, refer to thesection “Hill hold control system”.

NOTE:When the engine is restarted automati-cally, the following conditions may befound as the hill hold control system is acti-vated, but this is not a malfunction.• You may hear a sound from the engine

room.• As brake pedal becomes heavy, it may

be difficult for you to depress it.

Points to note during the automatic engine stopWhen the following operations are per-formed during the automatic engine stop,the engine may shut down, accompaniedby an interior buzzer or restarted, toensure safety.• When the hood is opened, an interior

buzzer will sound intermittently and theengine will come out of the automaticengine stop mode and shut down. TheENG A-STOP indicator light (green) willgo off.

• When the driver releases the seat belt oropens the driver’s door, the engine willrestart automatically. The ENG A-STOPindicator light (green) will blink forapproximately 5 seconds and then gooff.

• During the automatic engine stop, if thegearshift lever is shifted to a positionother than “N” without depressing theclutch pedal and open the driver’s doorwith the driver’s seat belt unfastened, aninterior buzzer will sound and the enginewill shut down without control of auto-matic engine stop. The ENG A-STOPindicator light (green) will go off.

NOTE:The power steering warning light, oil pres-sure warning light and charge warning lighton the meter panel do not come on duringthe automatic engine stop, but they willcome on once the engine shuts down.

Actuation conditions for ENG A-STOP system

Standby conditionsWhen all of the following conditions aremet while the vehicle is traveling, ENG A-STOP system will be permitted:• The engine is started with the hood com-

pletely closed.• The ENG A-STOP OFF switch has not

been pressed to deactivate the ENG A-STOP system.

• The lead-acid battery and the lithium-ionbattery are fully charged and the tem-perature inside the lead-acid battery orthe lithium-ion battery is within the speci-fied range (#1).

• The engine has warmed up and theengine coolant temperature is within thespecified range.

• The driver is wearing seat belts.• The driver’s door is completely closed.• The hood is completely closed.• No electronically controlled system

besides the ENG A-STOP system isissuing a signal to inhibit stopping of theengine (#2).

• The temperatures at air-conditioner out-lets are sufficiently low in the coolingmode or sufficiently high in the heatingmode.

• The defroster is turned off.#1 If the vehicle has not been in use for an

extended period of time or the audio orother electrical component was usedfor an extended period of time while the

3-24


72SM0-74E

engine was stopped, the lead-acid bat-tery may have discharged and it maytake some time before the standbymode is achieved.

#2 If any of the warning and indicator lightsaffecting the ENG A-STOP systemcome on, the engine will not be stoppedautomatically.

Automatic engine stop conditionsWhen all of the following conditions aremet under the standby conditions, theengine will stop automatically after thevehicle has stopped:• The gearshift lever is in “N” (Neutral)

position (for manual transmission vehi-cle).

• The clutch pedal is released (for manualtransmission vehicle).

• The vehicle has stopped.• The accelerator pedal is not depressed.• Neither the ABS nor ESP® is in opera-

tion.• The negative pressure of the brake

booster is normal.• The vehicle is stopped on a steep hill (for

automatic transmission vehicle).• The gearshift lever is in a position other

than “D” or “N” (for automatic transmis-sion vehicle).

• When the vehicle has stopped withoutdepressing the brake pedal (for auto-matic transmission vehicle).

Automatic engine restart conditionsIf one of the following operations is per-formed or the vehicle enters one of the fol-lowing modes during the automatic enginestop, the engine will restart automaticallyand the ENG A-STOP indicator light(green) will go off:

Common• The clutch pedal is depressed.• The ENG A-STOP OFF switch is

pressed to deactivate the ENG A-STOPsystem.

• The lead-acid battery or the lithium-ionbattery has discharged substantially (#).

• A malfunction of the system is detected(#).

• The negative pressure of the brakebooster has dropped (#).

• The temperatures at air conditioner out-lets have changed considerably after theautomatic engine stop to the point ofaffecting the cooling/heating perfor-mance (#).

• The temperature selector has beenturned considerably to the COOL side inthe cooling mode or to the HOT side inthe heating mode (#).

• The defroster is turned on (#).• The accelerator pedal depressed (for

automatic transmission vehicle) (#).• The gearshift lever is put in “P” or “R” (for

automatic transmission vehicle) (#).• After the gearshift lever is shifted to “N”,

it is returned to “D” (for automatic trans-mission vehicle) (#).

• The driver releases the seat belt (#).• The driver’s door is opened (#).• The vehicle starts to move on a slope,

etc. (#).• Some time (3 minutes or so) has

elapsed after the start of the automaticengine stop (#).

# The ENG A-STOP indicator light(green) will blink and then go off.

ENG A-STOP OFF SwitchThe ENG A-STOP system can be deacti-vated.

• To deactivate the system, press the ENGA-STOP OFF switch (1) to turn on ENGA-STOP OFF light (2).

• To activate the system once again, pressthe switch (1) again to turn off the indica-tor.

• Every time the engine is stopped manu-ally, the system is enabled again and theENG A-STOP OFF light (2) goes off.

3-25


72SM0-74E

72SM03006

NOTE:Pressing the ENG A-STOP OFF switch (1)during the automatic engine stop willrestart the engine automatically and theENG A-STOP OFF light (2) will come on.

ENG A-STOP OFF Light

52RM30460

This indicator comes on in the informationdisplay.

• This indicator comes on when the ENGA-STOP system is deactivated.

• The indicator blinks when the engineswitch is pressed to change the ignitionmode to ON, if one of the conditionslisted below is met.The ENG A-STOP system or the SmartHybrid system does not actuate correctlywhile the indicator is blinking. Have thesystem inspected by a Maruti Suzukiauthorised workshop.– There may be something wrong with

the ENG A-STOP system or the SmartHybrid system.

– An engine component (ISG) or thelead-acid battery is due for replace-ment.

NOTE:If the indicator blinks during the automaticengine stop, the engine may shut down.

Cruise ControlThe cruise control system allows you tomaintain a steady speed without keepingyour foot on the accelerator pedal. Thecontrols for operating the cruise controlsystem are on the steering wheel.

You can use the cruise control systemunder the following conditions:• For manual transmission vehicle, the

gear position is in 3rd, 4th or 5th.• For automatic transmission vehicle, the

gearshift lever is in “D” position.• The vehicle speed is about 40 km/h or

higher.

(2)(1)

EXAMPLE

WARNING

To help avoid loss of vehicle control,do not use the cruise control systemwhen driving in heavy traffic, on slip-pery or winding roads, or on steepdownhills.

3-26


72SM0-74E

Setting Cruising Speed

Cruise control switch

72RS050

(1) Cruise switch(2) “CANCEL” switch(3) “RES +/SET –” switch

72SM03005

(4) Cruise indicator(5) “SET” indicator(6) Set speed indication

1) Turn on the cruise control system bypushing cruise switch (1). When thecruise indicator (4) comes on, you canset cruising speed.

2) Accelerate or decelerate to the desiredspeed.

3) Push down the “RES +/SET –” switch(3), “SET” indicator (5) comes on. Also,set speed indication (6) comes on atthe same time. Take your foot off theaccelerator pedal and the set speed willbe maintained.

NOTE:Established cruising speed may differ a lit-tle from the speed meter indicationdepending on the road conditions.

Changing Speed TemporarilyWhen the cruising speed is maintained, youcan temporarily accelerate or decelerate.

To accelerate, depress the acceleratorpedal. When you take your foot off the pedal,your vehicle will return to the set speed.

To decelerate, depress the brake pedal.The set speed will be canceled and “SET”indicator (5) will go off.

To resume the previously set speed, pushup the “RES +/SET –” switch (3) and “SET”indicator (5) again when vehicle speed isabove 40 km/h. The vehicle will accelerateto the previously set speed and maintainits speed.

NOTE:For automatic transmission vehicle, whenthe cruising speed is maintained, you can-not decelerate by using the engine brakeeven if you downshift from higher gear to3rd in the manual mode.To decelerate while the cruise control ison, depress the brake pedal or push downthe “RES +/SET –” switch (3).

(1)(2)

(3)

(1)(2)

(3)

EXAMPLE

(5) (6)(4) (5) (6)(4)

WARNING

If the cruising speed is set by acci-dent, you cannot decelerate or couldloose control of the vehicle. Thiscould lead to an accident, resulting insevere injury or death.Turn off the cruise control systemand check that cruise indicator (4) isoff when the system is not in use.

3-27


72SM0-74E

Changing Cruising Speed

Using the accelerator pedalTo reset at a faster cruising speed, acceler-ate to the desired speed using the accelera-tor pedal and push down the “RES +/SET –”switch (3). The new speed will be main-tained.

Using the brake pedalTo reset at a slower cruising speed, decel-erate to the desired speed using the brakepedal and push down the “RES +/SET –”switch (3). The new speed will be main-tained.

NOTE:When the brake pedal is depressed, “SET”indicator (5) will go off until you reset thecruising speed.

Using “RES +/SET –” switchTo reset at a faster cruising speed, pressrepeatedly or hold push up the “RES +/SET –” switch (3). Vehicle speed willsteadily increase. When you release theswitch, the new speed will be maintained.

To reset at a slower cruising speed, pressrepeatedly or hold push down the “RES +/SET –” switch (3) until the vehicle hasslowed to the desired speed, and thenrelease the switch. The new speed will bemaintained.

NOTE:• You can adjust the set speed by approxi-

mately 1 km/h by pushing “RES +/SET –” switch quickly.

• When the current vehicle speed is about10 km/h or more faster than the previ-ously set speed, you cannot adjust afaster cruising speed by using the“RES +/SET –” switch (3).

• When the current vehicle speed is about10 km/h or more slower than the previ-ously set speed, you cannot adjust aslower cruising speed by using the“RES +/SET –” switch (3).

Cancelling Cruise Control“SET” indicator (5) will go off and thecruise control will be canceled temporarilywith the following conditions:

• Push “CANCEL” switch (2).• Depress the brake pedal.• For manual transmission, depress the clutch

pedal.• The vehicle speed falls more than about

20 percent from the set speed.• Any time the vehicle speed falls below

40 km/h.• When the vehicle skids and ESP® is

activated.

To resume the previously set speed, pushup the “RES +/SET –” switch (3) and turnon “SET” indicator (5). The vehicle speedmust be above 40 km/h when the vehicle isnot under the above conditions.

To turn off the cruise control system, pushcruise switch (1) and check that the cruiseindicator (4) is off.

Also, if the malfunction indicator light in theinstrument cluster comes on or blinks, thecruise control system will be turned off.

NOTE:If you turn off the cruise control system, thepreviously set speed in the memory iscleared. Reset your cruising speed again.

3-28


72SM0-74E

Parking SensorsThe parking sensor system uses ultrasonicsensors to detect obstacles near the rearbumper. If obstacles are sensed while youare parking or moving the vehicle slowly,the system warns you by sounding abuzzer and displaying symbols represent-ing the obstacles on the information dis-play in the instrument cluster.• The system emits an ultrasonic wave

and the relevant sensor detects thereturn of the wave reflected by an obsta-cle. The system measures the timetaken by the ultrasonic wave to reach theobstacle and return from it, from which itdetermines the obstacle’s position.

• The parking sensor function can be usedwhen the ignition mode to “ON”, thegearshift lever is in R position. This func-tion is helpful in the following cases: pull-ing over to the curb; parallel-parking thevehicle; steering the vehicle into agarage; driving along an alley; and mov-ing slowly in a place with obstacles.

Information Display Symbol

72RM03008

(1) Symbol representing an obstacledetected by parking sensor** This symbol shows that an obstacle

is located near the vehicle.

(1)(1)

EXAMPLE WARNING

• The parking sensor warns you ofobstacles with buzzers and byshowing you the location of theobstacles on the information dis-play. However, you must still payfull attention yourself while driving.

• The sensors can detect obstaclesonly within a limited area and onlywhen the vehicle is moving within alimited speed range. So, in trickyareas, you must move the vehicleslowly while checking around itusing your direct vision or rearviewmirrors. There is increased risk ofan accident if you control the vehi-cle relying only on the parking sen-sor.

3-29


72SM0-74E

Sensor Locations

72SM03004

(1) Rear center sensors (2 places)(2) Rear corner sensors (2 places)

NOTICE

• Avoid hitting the sensor areas ordirecting the nozzle of a high-pres-sure car washer onto the sensorareas. Otherwise, the sensors maybe damaged.

• If the bumper hits a hard object, thesensors on it may not work prop-erly. If this occurs, have the sen-sors inspected by a Maruti Suzukiauthorised workshop.

(1)(2) (1) (2)

EXAMPLE

Working sensorsThe sensors work depending on the position of gearshift lever as shown in the belowtable:

Gearshift lever positionManual Transmission Automatic Transmission

R N, 1st - 5th R N, D, 2 or L

Rear sensorsCenter On Off On Off

Corner On Off On Off

3-30


72SM0-74E

Approximate areas where obstacles canbe detected

60MH126

• An obstacle within about 20 cm (8 in)from a sensor or just below a sensor isnot detectable.

• The sensors can detect an obstacle upto about 1.5 m (5 ft) from the rear ofvehicle.

NOTE:• Thin poles or obstacles lower than the

sensors may become undetectable asthe vehicle moves closer to them even ifthey have been detected from longerdistances.

EXAMPLE

WARNING

• Under the following conditions, theparking sensor system may notwork normally because the sensorscannot detect obstacles correctly.– Sensors are covered with mud,

ice or other materials. (Suchmaterials must be removed fornormal operation.)

– Sensors are wet from watersplashes or heavy rain.

– Sensors are covered by a hand,sticker, accessory, etc.

– There is an accessory or otherobject attached within the sen-sor’s sensing area.

– Items such as tow hooks, com-mercially available corner poles,radio antenna, etc. are installedon the bumper.

– The height of the bumper ischanged due to alteration to thesuspension or other causes.

– The sensor areas are extremelyhot from direct sunlight or colddue to freezing weather.

– The vehicle is on a rough sur-face, slope, gravel road or grassfield.

– The vehicle is at a steep angle.(Continued)

WARNING

(Continued)– Sensors have intercepted ultra-

sonic noise from another vehi-cle’s horn, engine, air brakingsystem (large vehicles), or park-ing sensor.

– Obstacles are too close to thesensors.

– Sensors are at an angle to ahighly reflective object such asglass. (Ultrasonic waves are notreflected back from the obstacle.)

• Sensors may not be able to cor-rectly detect the following types ofobstacles:– Objects made of a thin material

like wire netting and ropes– Square-shaped curbstones or

other objects with sharp edges– Tall objects with a large upper

part like a road sign– Low-profile objects such as curb-

stones– Sound-absorbing objects such

as cotton and snow

3-31


72SM0-74E

• The system may calculate the distanceto a road sign or similar obstacle to beshorter than the actual distance.

Obstacle Indication by Parking Sen-sor

Information display symbol

72RM03009

(1) Obstacle detected by rear center sen-sors

(2) Obstacle detected by rear corner sen-sors

Upon detecting an obstacle, the parkingsensor causes an interior buzzer to soundand a symbol representing the obstacleappears on the information display in theinstrument cluster.• A different symbol is displayed depend-

ing on the direction and distance of theobstacle.

(1) (2)(2) (1) (2)(2)

EXAMPLE

• A buzzer located behind the rear seat sounds when a sensor at the rear detects anobstacle.

• Warnings when obstacles such as wall are detected by corner sensors

• Warnings when obstacles such as wall are detected by center sensors

NOTE:• Symbols are displayed with a short delay after the detection of obstacles.• If the system detects multiple obstacles simultaneously, the display shows all of their

positions using the corresponding symbols. However, the buzzers will sound only forthe nearest obstacles.

Distance (approx.) Buzzer Symbol45 – 60 cm(18 – 24 in) Short beeps at short intervals Three lines

35 – 45 cm(14 – 18 in) Short beeps at very short intervals Two lines

Less than 35 cm (14 in) Continuous beep One line

Distance (approx.) Buzzer Symbol60 – 150 cm(24 – 59 in) Short beeps at long intervals

Three lines45 – 60 cm(18 – 24 in) Short beeps at short intervals

35 – 45 cm(14 – 18 in) Short beeps at very short intervals Two lines

Less than 35 cm (14 in) Continuous beep One line

3-32


72SM0-74E

Warning and Indicator MessagesIf there is a problem or warning regarding the parking sensor system, a message is dis-played on the information display in the instrument cluster, and a symbol blinks and thebuzzer sounds. If a message is displayed, follow its instruction.

Message Symbol Buzzer Probable cause and remedy

68PH02303

Two blinking lines in a sen-sor location.

Series of double beeps

There may be a problem with the parking sensor system. Have your vehicle inspected by a Maruti Suzuki authorised work-shop.

68PH02304

One blinking line in a sensor location.

Series of single beeps

The indicated sensor is contami-nated.Wipe it clean with a soft cloth.

Rearview Camera (if equipped)When the gearshift lever is shifted to “R”position while the ignition mode is “ON”,the rearview camera system automaticallyshows the view behind the vehicle on thedisplay.

WARNING

The distance viewed in the rearviewcamera may differ from the actualdistance according to the conditionof road or the load the vehicle is car-rying. Since the camera display areais also limited, backing up by onlylooking at the display may cause anaccident or a collision with an object. The rearview camera cannot replacethe driver’s attention. The driveralone is responsible for parking andsimilar driving maneuvers.• Use the rearview camera only to

provide driving assistance. • Always drive carefully confirming

the safety of the rear and the sur-rounding conditions by lookingdirectly with your eyes and usingthe rear view mirror.

• Check that the tailgate is securelyclosed when backing up.

3-33


72SM0-74E

Rearview Camera Location

72SM03002

(1) Rearview camera

The rearview camera is installed besidethe license plate light.

NOTE:If body wax gets on the camera lens, wipeoff the wax with a clean cloth dampenedwith mild detergent diluted with water, andthen wipe the lens with a dry cloth.

How to Use Rearview Camera1) Press the engine switch to change the

ignition mode to “ON”. 2) Shift the gearshift lever in “R” position.

•The display automatically shows theview behind the vehicle.

•When the gearshift lever is shifted from“R” to another gearshift lever posi-tion, the display returns to the previ-ous display.

NOTE:The rearview camera display has first pri-ority in any display mode. However, therearview camera display does not showthe rear view while the system is initializ-ing.

Display Range of Rearview CameraThe rearview camera display shows thearea behind the rear end of the tailgate.The display cannot show objects which areclose to the bumper or under the bumper.The rearview camera display cannot showobstacles which are higher than the cam-era. Upper parts of tall objects such asroad signs cannot be viewed on the dis-play.

NOTICE

If you use the rearview camera for along time when the ignition mode is“ON”, but the engine is not running,the lead-acid battery may discharge.Do not leave the ignition mode “ON”for a long time when the engine is notrunning.

(1)

EXAMPLE

NOTICE

The rearview camera is a precisioninstrument. If you strike the camera,it may be broken and cause damageresulting in a catch fire or a malfunc-tion. • Do not strike the camera.• Do not remove snow or mud on the

camera lens with a stick.

NOTICE

If water enters the rearview camera, itmay cause a malfunction or catchfire.Do not use high pressure wateraround the camera.

NOTICE

This lens is hard coated to preventdamage or discoloration. Damage ordiscoloration of lens may obscurethe image.• Do not use a brush to clean lens. • Do not use alcohol, benzene or

thinner to clean the lens.• Do not use wax on the camera lens.

3-34


72SM0-74E

Display range of rearview camera

72R0039

61MM0B012

(1) Display range

NOTE:• Images shown on the display from the

rearview camera are reversed images(mirror images).

• The colors of objects on the rearviewcamera may differ from the actual objectcolors.

• The rearview camera display may be dif-ficult to see under the following condi-tions, but this is not a systemmalfunction. – In dark areas, on a rainy day or at

night. – When the temperature around the lens

is too high/low, or the camera is wetsuch as on a rainy day or during peri-ods of high humidity (dew condensa-tion may occur on the camera lens).

– When a foreign object such as mud ora drop of water is stuck around thecamera lens.

– When strong light directly enters thecamera (vertical lines may be seen onthe display).

– Under fluorescent light. (The displaymay flicker.)

– When the outside temperature is low(the image on the display may bedarkened).

Rearview camera screen indicationThe distance viewed in the rearview cam-era may differ from the actual distanceaccording to the condition of the road orthe load the vehicle is carrying.

Uphill incline behind the vehicle

72R0040

(1) Object(2) Actual distance(3) Distance on the display

When there is an uphill incline behind thevehicle, the object shown on the displayappears farther away than the actual dis-tance.

(1)

EXAMPLE

(1)EXAMPLE

(1)

(2)

(3)

EXAMPLE

3-35


72SM0-74E

Downhill incline behind the vehicle

72R0041

(1) Object(2) Actual distance(3) Distance on the display

When there is a downhill incline behind thevehicle, the object shown on the displayappears closer than the actual distance.

If the rear view from the rearview cam-era is not shown or there is a poorimage• If the rear view from the rearview camera

is not shown. – Check that the ignition mode is “ON”.– Check that the gearshift lever is

shifted to “R” position.• If the image from the rearview camera is

poor. – Check that the camera lens is not dirty. – Check that light from the sun or the

beam of the headlights from the vehi-cle behind is not shining directly intothe lens.

If the rearview camera system is still notworking properly after checking the above,have the system inspected by a MarutiSuzuki authorised workshop as soon aspossible.

Braking

60G165A

The distance needed to bring any vehicleto a halt increases with the speed of thevehicle. The braking distance needed, forexample, at 60 km/h will be approximately4 times greater than the braking distanceneeded at 30 km/h. Start to depress thebrake pedal when there is plenty of dis-tance between your vehicle and the stop-ping point, and slow down gradually.

(1)

(3)

(2)

(1)

(3)

(2)

EXAMPLEEXAMPLE

3-36


72SM0-74E

Power-Assisted BrakesYour vehicle has power-assisted brakes. Ifpower assistance is lost due to a stalledengine or other failures, the system is stillfully operational on reserve power and youcan bring the vehicle to a complete stop bypressing the brake pedal once and holdingit down. The reserve power is partly usedup when you depress the brake pedal andreduces each time the pedal is pressed.Apply smooth and even pressure to thepedal. Do not pump the pedal.

Anti-Lock Brake System (ABS)ABS will help you avoid skidding by elec-tronically controlling braking pressure. Itwill also help you maintain steering controlwhen braking on slippery surfaces or whenbraking hard.The ABS works automatically, so you donot need any special braking technique.Just push the brake pedal down withoutpumping. The ABS will operate wheneverit senses that the wheels are locking up.You may feel the brake pedal moves a littlewhile the ABS is operating.

NOTE:• The ABS will not work if vehicle speed is

under about 9 km/h.• If the ABS system is activated, you may

hear a clunking noise and/or feel pulsat-ing in the brake pedal. This is normaland indicates that the brake fluid pres-sure is being controlled properly.

• You may hear an operation sound whenyou start the engine or after the vehiclebegins to move. This means that theabove systems are in the self-checkmode. This sound does not indicate amalfunction.

WARNING

If water gets into the brake devices,brake performance may become poorand unpredictable. After drivingthrough water or washing the under-side of the vehicle, test the brakeswhile driving at a slow speed to see ifthey have maintained their normaleffectiveness. If the brakes are lesseffective than normal, dry them byrepeatedly applying the brakes whiledriving slowly until the brakes haveregained their normal effectiveness. WARNING

Even without reserve power in thebrake system, you can still stop thevehicle by pressing the brake pedalharder than normally required. How-ever, the stopping distance may belonger.

3-37


72SM0-74E

54MN069

(1) ABS warning light(2) Brake system warning light

WARNING

• On some types of loose surfaces(such as gravel, snow-coveredroads, etc.), the stopping distancerequired for a vehicle with ABSmay be slightly greater than theone required for a comparable vehi-cle with a conventional brake sys-tem. With a conventional brakesystem, skidding tires are able toplow the gravel or snow layer,shortening the stopping distance.ABS minimizes this resistanceeffect. Allow for extra stopping dis-tance when driving on loose sur-faces.

• On regular paved roads, some driv-ers may be able to obtain slightlyshorter stopping distances withconventional brake systems thanwith ABS.

• In both of the above conditions,ABS will still offer the advantage ofhelping you maintain directionalcontrol. However, remember thatABS will not compensate for badroad or weather conditions or poordriver judgment. Use good judg-ment and do not drive too fast.

(1) (2)(1) (2)

EXAMPLE WARNING

• If the ABS warning light (1) on theinstrument panel comes on andstays on while driving, there maybe a problem with the ABS system.Ask a Maruti Suzuki authorisedworkshop to inspect the ABS sys-tem immediately. If the ABS systembecomes inoperative, the brakesystem will function as an ordinarybrake system that has no ABS.

• If the ABS warning light (1) and theBrake system warning light (2) onthe instrument panel simultane-ously stays on or comes on whiledriving, both anti-lock function andrear brake force control function(proportioning valve function) ofthe ABS system may have failed. Ifso, the rear wheels may easily skidor the vehicle can even spin in theworst case when braking on a slip-pery road or when hard brakingeven on a dry paved road. Ask aMaruti Suzuki authorised workshopto inspect the ABS system immedi-ately. Drive carefully, avoiding hardbraking as much as possible.

3-38


72SM0-74E

How the ABS WorksA computer continuously monitors wheelspeed. The computer compares thechanges in wheel speed when braking. Ifthe wheels slow suddenly, indicating askidding situation, the computer willchange braking pressure several timeseach second to prevent the wheels fromlocking. When you start your vehicle orwhen you accelerate after a hard stop, youmay hear a momentary motor or clickingnoise as the system resets or checks itself.“This is absolutely normal and indicate thatABS is functioning properly”.

Electronic stability program (ESP®) (if equipped)ESP® is a registered trademark of DaimlerAG.

The Electronic Stability Program (ESP®)helps to control the vehicle during corner-ing if front wheels or rear wheels skid. Italso assists you in maintaining tractionwhile accelerating on loose or slipperyroad surfaces. It does this by regulatingthe engine’s output, and by selectivelyapplying the brakes. In addition, ESP®

helps to avoid skidding by controlling brak-ing pressure.

The ESP® totally manages following foursystems, (stability control, traction control,ABS and Brake assist) to help enhancevehicle stability in response to various driv-ing conditions;

Stability control systemThe vehicle stability control system helpsprovide integrated control of systems suchas anti-lock brakes, traction control, enginecontrol, etc. This system automaticallycontrols the brakes and engine to help pre-vent the vehicle from skidding when cor-nering on a slippery road surface or whenturning the steering wheel abruptly.

Traction control systemThe traction control system automaticallyhelps prevent the spinning of wheels whenthe vehicle is started or accelerated onslippery road surfaces. The system oper-ates only if it senses that some of thewheels are spinning or beginning to losetraction. When this happens, the systemoperates the front or rear brakes andreduces engine power to limit wheel spin.

NOTE:You may hear an operation sound whenyou start the engine or after the vehiclebegins to move. This means that theabove systems are in the self-check mode.This sound does not indicate a malfunc-tion.

WARNING

The ABS may not work properly iftires or wheels other than thosespecified in the owner’s manual areused. This is because the ABS worksby comparing changes in wheelspeed. When replacing tires orwheels, use only the size and typespecified in this owner’s manual.

WARNING

The ESP® cannot enhance the vehi-cle’s driving stability in all situationsand does not control your vehicle’sentire braking system. The ESP® can-not prevent accidents, includingthose resulting from excessive speedin turns, or hydroplaning. Only safeand attentive drive can prevent acci-dents. The capabilities of an ESP®-equipped vehicle must never be usedas a substitute for careful driving.

3-39


72SM0-74E

Anti-Lock Brake System (ABS)ABS will help you avoid skidding by elec-tronically controlling braking pressure. Itwill also help you maintain steering controlwhen braking on slippery surfaces or whenbraking hard. The ABS works automati-cally, so you do not have to use any spe-cial braking technique. Just push the brakepedal down without pumping. The ABS willoperate whenever it senses that wheelsare locking up. You may feel the brakepedal pulsate while the ABS is operating.(For more information on ABS, see “Brak-ing” in this section.)

NOTE:• The ABS will not work if vehicle speed is

under about 9 km/h.• If the ABS system is activated, you may


Brake assist systemWhen you step on the brake pedal, thebrake assist system determines it to be anemergency stop and provides more power-ful braking for a driver who cannot holddown the brake pedal firmly.

NOTE:If you quickly and forcefully depress thebrakes, you may hear a clicking sound inthe brake pedal. This is normal and indi-

cates that the brake assist system is acti-vated properly.

NOTE:• If the ESP® system is activated, you may


• You may hear an operation sound whenyou start the engine or after the vehiclebegins to move. This means that theabove systems are in the self-checkmode. This sound does not indicate amalfunction.

The ESP® indicator lights are describedbelow:

ESP® warning light

52KM133

This light blinks 5 times per second whenone of the following systems is activated.• Stability control system• Traction control systemIf this light blinks, drive carefully.


WARNING

• The ESP® may not work properly iftires or wheels other than thosespecified in the owner’s manual areused. When replacing tires orwheels, use only the size and typespecified in this owner’s manual.

• The ESP® may not work properly iftires are not inflated to the recom-mended tire pressure.

• The ESP® may not work properly iftires are fitted with tire chains.

• The ESP® may not work properly ifthe tires are excessively worn.Replace tires when the tread wearindicators in the grooves appear onthe tread surface.

• The ESP® is not a substitute forwinter tires or tire chains on asnow-covered road.

WARNING

• The ESP® may not work properly ifengine related parts such as themuffler are not equivalent to stan-dard equipment or are extremelydeteriorated.

• Do not modify the vehicle’s sus-pension since the ESP® may notwork properly.

3-40


72SM0-74E

NOTE:When the ESP® warning light comes onand stays on while driving, indicating amalfunction of the ESP® systems (otherthan ABS), the brake system will functionas an ordinary ABS with no additionalESP® functions.

ESP® OFF indicator light

73R0196

You should turn the ESP® on during yourordinary driving, so that you have the ben-efits of all of the ESP® systems.

It may be required to turn the ESP® sys-tems (other than ABS) off if your vehicle isstuck in sand, mud, or snow, where wheelspin is necessary.

ESP® OFF switch

75RM055

(1) ESP® OFF switch

When the ESP® OFF switch located at theinstrument panel is pushed and held toturn off the ESP® systems (other thanABS), the ESP® OFF indicator light in theinstrument cluster comes on.When you have turned the ESP® systems(other than ABS) off, turn them back onbefore resuming ordinary driving.When you push the ESP® OFF switchagain, the ESP® OFF indicator light will goout and all of the ESP® systems will beactivated.

ABS warning light / brake system warning lightSee “Braking” in this section.

Hill hold control system(if equipped)The hill hold control system is designed toassist you in starting to move up hills.When you start to move up a hill, the sys-tem helps to prevent the vehicle from roll-ing downward (for approximately 2seconds) while you move your foot fromthe brake pedal to the accelerator pedal.

NOTICE

If the ESP® warning light comes onand stays on while driving, there maybe a malfunction of the ESP® sys-tems (other than ABS). You shouldhave the systems inspected by aMaruti Suzuki authorised workshop.

(1)(1)

EXAMPLE

3-41


72SM0-74E

The hill hold control system activates for amaximum of about 2 seconds if your foot ismoved from the brake pedal when the fol-lowing conditions are all met.

1) The gearshift lever is in a forward gearor reverse gear.

2) The parking brake is released.3) The vehicle is on an upward incline.

The hill hold control system is activatedwhen the engine is restarted after beingstopped automatically, even if the previousconditions are not met.

NOTE:When the hill hold control system is acti-vated, the following conditions may befound, but this is not a malfunction.• You may hear a sound from the engine

room.• As brake pedal becomes heavy, it may

be difficult for you to depress it.

WARNING

• Do not rely excessively on the hillhold control system. The hill holdcontrol system may not prevent thevehicle from rolling downward on ahill under all load or road condi-tions. Always be prepared todepress the brake pedal to preventthe vehicle from rolling downward.Failure to pay attention anddepress the brake pedal to hold thevehicle on a hill when necessary,may result in loss of control or anaccident.

• The hill hold control system is notdesigned to stop the vehicle on ahill.

• After you release your foot from thebrake pedal, accelerate the vehicleto move up immediately. If yourelease your foot from the brakepedal over 2 seconds, the hill holdcontrol system will be canceled. Ifso, the vehicle may roll downward,which can result in an accidentdepending on the degree of slope.And, the engine may stall and thepower assist for the steering andbrakes will not work so steeringand braking will be much harderthan usual which can result in anaccident or vehicle damage.

DRIVING TIPS

4

72SM0-74E

72RM04000

DRIVING TIPSRunning-in ........................................................................... 4-1Catalytic Converter ............................................................. 4-1Improving Fuel Economy ................................................... 4-2Highway Driving .................................................................. 4-3Driving on Hills .................................................................... 4-3Driving on Slippery Roads ................................................. 4-4Off-road Driving ................................................................... 4-6When Encountering a Flooded Area ................................. 4-6Do’s and Dont’s for safe driving ........................................ 4-7Margin for safety ................................................................. 4-9

4-1

DRIVING TIPS

72SM0-74E

55RM04002

Running-in Catalytic Converter

80G106

The purpose of the catalytic converter is tominimize the amount of harmful pollutantsin your vehicle’s exhaust. Use of leadedfuel in vehicles equipped with catalyticconverters is prohibited, because leaddeactivates the pollutant-reducing compo-nents of the catalyst system.

The converter is designed to last the life ofthe vehicle under normal usage and whenunleaded fuel is used. No special mainte-nance is required on the converter. How-ever, it is very important to keep the engineproperly tuned. Engine misfiring, which canresult from an improperly tuned engine,may cause overheating of the catalyticconverter. This may result in permanentheat damage to the catalytic converter andother vehicle components.

WARNING

• Fasten Your Seat Belts at All Times.Even though airbags are equippedat the front seating positions, thedriver and all passengers shouldbe properly restrained at all times,using the seat belts provided. Referto “Seat Belts and Child RestraintSystems” section for instructionson proper use of the seat belts.

• Never drive while under the influ-ence of alcohol or other drugs.Alcohol and drugs can seriouslyimpair your ability to drive safely,greatly increasing the risk of injuryto yourself and others. You shouldalso avoid driving when you aretired, sick, irritated, or understress.

EXAMPLE

NOTICE

The future performance and reliabil-ity of the engine depends on the careand restraint exercised during itsearly life. It is especially important toobserve the following precautionsduring the first 960 km of vehicleoperation.• After starting, do not race the

engine. Warm it up gradually.• Avoid prolonged vehicle operation

at a constant speed. Moving partswill break in better if you vary yourspeed.

• Start off from a stop slowly. Avoidfull throttle starts.

• Avoid hard braking, especiallyduring the first 320 km of driving.

• Do not drive slowly with the trans-mission in a high gear.

• Drive the vehicle at moderateengine speeds.

EXAMPLE

4-2

DRIVING TIPS

72SM0-74E

72SM04001

Improving Fuel EconomyThe following instructions will help youimprove fuel economy.

Avoid excessive idlingIf you park your vehicle for more than oneminute, stop the engine and start it againlater. When warming up a cold engine, donot allow the engine to idle or apply fullthrottle until the engine has reached oper-ating temperature. Allow the engine towarm up by driving.

Avoid sudden accelerationSudden acceleration starting from rest orwhile driving will consume fuel unneces-sarily and shorten engine life. Start offslowly.

Avoid unnecessary stopsAvoid unnecessary deceleration and stop-ping. Try to maintain a moderate, steadyspeed whenever possible. Slowing downand then accelerating again uses morefuel.

Keep a steady cruising speedDrive at a constant speed that road andtraffic conditions will permit.

NOTICE

To minimize the possibility of cata-lytic converter or other vehicle dam-age:• Maintain the engine in the proper

operating condition.• In the event of an engine malfunc-

tion, particularly one involvingengine misfiring or other apparentloss of performance, have the vehi-cle serviced promptly.

• Do not turn off the engine or inter-rupt the ignition when the transmis-sion is in gear and the vehicle is inmotion.

• Do not try to start the engine bypushing or towing the vehicle, orcoasting down a hill.

• Do not idle the engine with anyspark plug wires disconnected orremoved, such as during diagnos-tic testing.

• Do not idle the vehicle for pro-longed periods if idling seemsrough or there are other malfunc-tions.

• Do not allow the fuel tank to getnear the empty level.

• Avoid driving your vehicle atexcessively high engine speed inor around the red zone of thetachometer.

WARNING

Be careful where you park and drive;the catalytic converter and otherexhaust components can get veryhot. As with any vehicle, do not parkor operate this vehicle in areas wherecombustible materials such as drygrass or leaves can come in contactwith a hot exhaust system.

EXAMPLE

4-3

DRIVING TIPS

72SM0-74E

Keep the air cleaner clean

60A183S

If the air cleaner is clogged with dust, therewill be greater intake resistance, resultingin decreased power output and increasedfuel consumption.

Keep weight to a minimumThe heavier the load is, the more fuel thevehicle consumes. Unload any unneces-sary luggage or cargo.

Keep tire pressures correctUnder-inflation of the tires can waste fueldue to increased rolling resistance of thetires. Keep your tires inflated to the correctpressure shown in the label on driver’sdoor lock pillar.

Highway DrivingWhen driving at highway speeds, payattention to the following:• Stopping distance progressively

increases with vehicle speed. Apply thebrakes far enough ahead of the stoppingpoint to allow for the extra stopping dis-tance.

• On rainy days, hydroplaning can occur.Hydroplaning is the loss of direct contactbetween the road surface and the vehi-cle’s tires due to a water film formingbetween them. Steering or braking thevehicle during hydroplaning can be verydifficult, and loss of control can occur.Keep speed down when the road sur-face is wet.

• At high speeds, the vehicle may beaffected by side winds. Therefore,reduce speed and be prepared for unex-pected buffeting, which can occur at theexits of tunnels, when passing by a cutof a hill, or when being overtaken bylarge vehicles, etc.

Driving on Hills

72RM04008

• When climbing steep hills, the vehiclemay begin to slow down and show a lackof power. If this happens, you shouldshift to a lower gear so that the enginewill again be operating in its higherpower range. Shift rapidly to prevent thevehicle from losing momentum.

• When driving down a hill, the engineshould be used for braking by shifting tothe next lower gear.

EXAMPLE

MT

AT

MT

AT

EXAMPLE

4-4

DRIVING TIPS

72SM0-74E

While moving uphill/gradient from astand still condition - For manual tran-saxle• Apply the parking brake firmly so that the

vehicle does not roll backwards. • Depress the Clutch pedal and Shift the

gearshift lever to 1st Select position. • Do not slip the clutch.• When ready to start, press accelerator

pedal and slowly release the clutchpedal simultaneously. When the vehiclestarts to move, gradually release theparking brake.

Driving on Slippery Roads

72SM04002

On wet roads, you should drive at a lowerspeed than you do on dry roads due topossible slippage of tires during braking.When driving on icy, snow-covered, ormuddy roads, reduce your speed andavoid sudden acceleration, abrupt braking,or sharp steering movements.

Snow ChainsSnow chains should only be used if theyare needed to increase traction or arerequired by law. Make sure that the chainsyou use are the correct size for your vehi-cle’s tires. Also make sure that there isenough clearance between the fendersand the chains as installed on the tires.

Install the chains on the front tires tightly,according to the chain manufacturer’sinstructions. Retighten the chains afterdriving about 1.0 km if necessary. With thechains installed, drive slowly.

WARNING

Do not hold the brake pedal down toolong or too often while going down asteep or long hill. This could causethe brakes to overheat, resulting inreduced braking efficiency. Failure totake this precaution could result inloss of vehicle control.

NOTICE

When descending a downhill, neverpress the engine switch to changethe ignition mode to “LOCK” (OFF).Emission control system and auto-matic transmission (if equipped)damage may result.

EXAMPLE

NOTICE

• If you hear the chains hittingagainst the vehicle body while driv-ing, stop and tighten them.

• If your vehicle is equipped with fullwheel caps, remove the wheel capsbefore installing the chains or thewheel caps can be damaged by thechain bands.

4-5

DRIVING TIPS

72SM0-74E

Stuck VehicleIf your vehicle gets stuck in snow, mud, orsand, follow the directions below:

1) Shift the transmission back and forthbetween a forward range (or first gearfor manual transmission) and reverse.This will create a rocking motion whichmay give you enough momentum tofree the vehicle. Press gently on theaccelerator to keep wheel spinning to aminimum wheel rpm. Remove your footfrom the accelerator while shifting. Do not race the engine. Excessivewheel spin will cause the tires to digdeeper, making it more difficult to freethe vehicle.

NOTE:If your vehicle is equipped with the ESP®,you may have to turn the ESP® system offin order to allow spinning the wheels.

2) If your vehicle remains stuck after a fewminutes of rocking, we recommend youto consult a Maruti Suzuki authorisedworkshop or a roadside assistance ser-vice. If a towing service is not availablein an emergency, your vehicle may betemporarily towed by other vehicle witha towing cable or chain secured to thetowing eye either on the front of thevehicle or on the rear of the vehicle.Refer to “Frame Hooks” in “OTHERCONTROLS AND EQUIPMENT” sec-tion.

72SM04003

WARNING

Do not allow anyone to stand nearthe vehicle when you are rocking it,and do not spin the wheels fasterthan an indicated 40 km/h on thespeedometer. Personal injury and/ orvehicle damage may result from spin-ning the wheels too fast.

NOTICE

Do not continue rocking the vehiclefor more than a few minutes. Pro-longed rocking can cause engineoverheating or transmission damage.

EXAMPLE

WARNING

In addition to following the drivingtips in this section, it is important toobserve the following precautions.• Make sure your tires are in good

condition and always maintain thespecified tire pressure. Refer to“Tires” in the “INSPECTION ANDMAINTENANCE” section fordetails.

• Do not use tires other than thosespecified by MARUTI SUZUKI.Never use different sizes or typesof tires on the front and rearwheels. For information regardingthe specified tires, refer to the tireinformation label located on thedriver’s door lock pillar.

• Never use oversized tires or spe-cial shock absorbers and springsto raise (jack up) your vehicle. Thiswill change the handling character-istics. Oversized tires may also rubagainst the fender over bumps,causing vehicle damage or tire fail-ure.

(Continued)

4-6

DRIVING TIPS

72SM0-74E

Off-road Driving

Do not drive in the field covered with grown grassIf you drive in the field covered with grass,it may cause accident or vehicle damageby getting caught in grown grass.

When Encountering a Flooded Area

72SM04004

Avoid driving in a flooded area or a deeppuddle. If driving in a flooded area isunavoidable, go slowly in the lowest gear.In case that you have driven in a floodedarea, stop the vehicle in a safe place whilechecking the brake effectiveness. Then,ask a Maruti Suzuki authorised workshopto check the following inspection items.

• Function of brake• Function of electrical components• Changes of oil level and quality for

engine, transmission and differential. Incase that the oil is turbid whitely, waterhas been mixed in the oil and an oilchange is required.

• Lubricant condition of the bearings, sus-pension joints, etc.

WARNING

(Continued)• After driving through water, test the

brakes while driving at a slowspeed to see if they have main-tained their normal effectiveness. Ifthe brakes are less effective thannormal, dry them by repeatedlyapplying the brakes while drivingslowly until the brakes haveregained their normal effective-ness.

EXAMPLE

NOTICE

• Avoid driving in a flooded area or adeep puddle. It may cause anengine stall, short in electrical com-ponents, engine and transmissiondamages, etc.

• If the vehicle get stuck in deepwater do not start the engine.

4-7

DRIVING TIPS

72SM0-74E

Do’s and Dont’s for safe drivingExercise care in handling your vehicle. Beconscious of not only your own safety butalso the safety of others on the road, andthus enjoy the best and most comfortabledriving experience.

Following are basic rules for safe driving.Read them carefully for good understand-ing of the content so that you can enjoysafe and pleasant driving in your vehicle.

Starting1) Adjust the driver’s seat for the proper

driving posture.2) Adjust the rear view mirror so as to

obtain the best possible rear view.

72RM04001

3) Before moving, look around your vehi-cle to confirm safety.

4) Don’t accelerate suddenly, since it isdangerous and wastes fuel.

General Driving1) Be sure to stop before a stop light or

stop sign. When moving into an inter-section without any traffic lights orsigns, drive slowly to confirm safety.

2) Always follow other vehicles at a safedistance in order to prevent a rear-endcollision, in case the vehicle aheadmakes a sudden stop.

72SM04005

3) Turn on the turn signal at least 30meters before making a turn or chang-ing the lane so as not to be hit.

4) Before entering a corner, decelerate toa safe speed. Don’t apply brakes duringcornering, or skidding may occur.

5) When overtaking other vehicles, watchout for oncoming vehicles and carefullyensure safety.

6) Don’t attempt zigzag driving as it willhinder your control over the vehicle andmay cause an accident.

7) Avoid reckless high speed driving andtry to drive at a safe speed suitable forthe road conditions while maintaining aconstant speed.

8) The higher the speed, the narrower thedriver’s visual range becomes. In sucha state, it is difficult to anticipate anyhazard and the driver feels fatigued.

72RM04003

9) Do not attempt sharp handling duringhigh speed driving. You may lose yourcontrol over your vehicle.

10)When overtaking or changing laneswhile driving at a high speed, keepample vehicle-to-vehicle distance.

EXAMPLE

EXAMPLE EXAMPLE

4-8

DRIVING TIPS

72SM0-74E

Braking

72RM04004

1) Use the parking brake when parkingyour vehicle and shift the gear shiftlever into the first gear or reverse gearposition for the sake of safety.

2) Don’t use hand-braking unlessunavoidable. It causes the vehicle toskid and a collision may occur. It isespecially dangerous when the tires areworn out as they skid more.

72SM04006

Use foot brake in three stages1. Warn the vehicle behind you.2. Gradually apply the brake.3. Bring the vehicle to a halt.

3) When driving downhill, try not to applythe brake but use the engine brakeeffectively. Overuse of the foot-brakemay result in reduction of brake effec-tiveness.

Long Distance Driving1) Be sure to perform safety checks

before starting a trip.2) Take rest at regular intervals to prevent

accidents which may occur due to feel-ing sleepy or tired.

Night Time Driving

72SM04007

1) Drive at lower speeds during the nightthan in the daytime, as the visual rangeis restricted at night.

2) Avoid overtaking other vehicles at night.Darkness bothers your sense of speedand hinders your judgment of vehicle-to-vehicle distance.

EXAMPLEEXAMPLE

EXAMPLE

4-9

DRIVING TIPS

72SM0-74E

72F-08-021

3) Don’t use headlights on high beamunless its use is inevitable. It maycause visual impairment to the driver ofthe oncoming vehicle or the vehicleahead of you, which may cause anaccident.

4) Always keep the window glasses clean.Don’t operate the windshield wiperwhen the windshield glass is dry elsethe wiper blade and glass may getdamaged.

Margin for safetyIt is important to allow yourself a margin forsafety during driving so that you can copewith erroneous or unexpected driving ofother drivers. For that, observe the follow-ing.• Drive at a safe speed.• Maintain a sufficient distance between

your vehicle and the vehicle ahead.• Don’t force yourself to overtake other

vehicles.• Don’t accelerate suddenly, steer sharply

or stop suddenly.• Keep ample gaps between driving

schedules.• Observe traffic rules and regulations.

ConclusionA perfect driver does not exist. Theendeavour of every motorist should be tostrive for perfection. Safety consciousnessnot only ensures your safety and the safetyof other road users, it also helps reducethe wear and tear on your vehicle, length-ens its life, gives better fuel efficiency andensures a comfortable driving experience.Follow the do’s and dont’s listed, anddriving will never be the same again.

EXAMPLE

OTHER CONTROLS AND EQUIPMENT

5

72SM0-74E

60G407

OTHER CONTROLS AND EQUIPMENTHeating and Air Conditioning System ............................... 5-1Automatic Heating and Air Conditioning System(climate control) ................................................................... 5-4Radio Antenna ..................................................................... 5-10Installation of Radio Frequency Transmitters .................. 5-10Fuel Filler Cap ..................................................................... 5-10Engine Hood ........................................................................ 5-12Sun Visor ............................................................................. 5-14Interior Light ........................................................................ 5-15Accessory Socket ............................................................... 5-16Assist Grips ......................................................................... 5-17Glove Box ............................................................................ 5-18Overhead Console .............................................................. 5-19AUX/USB Socket ................................................................. 5-19Cup Holder and Storage Area ............................................ 5-20Footrest (if equipped) ......................................................... 5-23Front Seat Back Pocket ...................................................... 5-23Luggage Box ....................................................................... 5-23Roof Rail .............................................................................. 5-24Frame Hooks ....................................................................... 5-25

5-1


72SM0-74E

Heating and Air Conditioning System

Air Outlet

72SM05001

3

1

2 2

443

556 6

EXAMPLE

1. Windshield defroster outlet2. Side defroster outlet3. Side outlet4. Center outlet5. Floor outlet6. Cup holder outlet

5-2


72SM0-74E

Center outlet

72SM05002

Move the knob (1) vertically or horizontally to adjust the direction of air flow as desired.

(1) (1)

EXAMPLESide outlet

73R0076

When open, air comes out regardless ofthe air flow selector position.

Move the knob (1) vertically or horizontally,to adjust the direction of air flow asdesired.The side outlet opens when you turn thedial (2) upward and closes when you turn itdownward.

(2)(2)(1)(1) 2(22)1((1)

EXAMPLE

5-3


72SM0-74E

Overhead rear air conditioning system

73R0077

To turn on the overhead rear air condition-ing system, set the blower speed selectorof the heating and air conditioning systemto a position other than off and push in “A/C” switch. Refer to “Air conditioning switch”in this section. And set the rear blowerspeed selector (2) to a position other thanoff.

Move the knob (1) vertically or horizontallyto adjust the direction of air flow asdesired.

During operation of the air conditioner, youmay notice slight changes in enginespeed. These changes are normal, thesystem is designed so that the compressorturns on or off to maintain the desired tem-perature. Less operation of the compres-sor results in better fuel economy.

CAUTION

Prolonged exposure to hot air fromthe heater or air conditioner couldresult in low temperature burns. Allvehicle occupants, particularly chil-dren, the elderly, those with specialneeds, individuals with delicate skin,and sleeping individuals, shouldmaintain sufficient distance from theair outlets to prevent prolongedexposure to hot airflow.

(1)(1)

(2)

EXAMPLE

5-4


72SM0-74E

Automatic Heating and Air Conditioning System (climate control)

Description of Controls

72R0002

84

2

7 3

5 9 6 1

84

2

7 3

5 9 6 1EXAMPLE

1. Temperature selector2. Blower speed selector3. Air intake selector4. Air flow selector5. Defrost switch6. Air conditioning switch7. “OFF” switch8. “AUTO” switch9. Display

Temperature selector (1)

72R0003

Turn the temperature selector (1) to adjustthe temperature.

NOTE:If you turn the temperature selector (1)until “HI” or “LO” appears on the display,the climate control system will operate atmaximum heating or cooling. The tempera-ture of the air from the outlets may change

(1)

EXAMPLE

5-5


72SM0-74E

suddenly while “LO” or “HI” is displayed,but this is normal.

NOTE:When you change the unit of temperaturein the information display, the unit of tem-perature in the air conditioning system willbe changed. Refer to “Information display”in the “BEFORE DRIVING” section fordetails.

Blower speed selector (2)

72R0004

The blower speed selector (2) is used toturn on the blower and to select blowerspeed.

If “AUTO” switch (8) is pushed, the blowerspeed will vary automatically as the cli-mate control system maintains theselected temperature.

Air intake selector (3)

72R0005

Push the air intake selector (3) to changebetween the recirculated air and fresh airmode.

If “AUTO” switch (8) is pushed, the airintake will vary automatically as the climatecontrol system maintains the selected tem-perature.

NOTE:When the recirculated air mode isselected, the automatic operation systemis deactivated even if you push “AUTO”switch (8).

RECIRCULATED AIR (a)When this mode is selected, outside air isshut off and inside air is recirculated. Thismode is suitable when driving throughdusty or polluted air such as a tunnel, orwhen attempting to quickly cool down orwarm up the interior.

FRESH AIR (b)When this mode is selected, outside air isintroduced.

FRESH AIR and RECIRCULATED AIR areselected alternately each time the airintake selector is pushed.

NOTE:If you select RECIRCULATED AIR for anextended period of time, the air in the vehi-cle can become contaminated and the win-dows tend to get misted. Therefore, youshould select FRESH AIR whenever possi-ble.

(2)

EXAMPLE

(a)

(b)

(3)

(a)

(b)

(3)

EXAMPLE

5-6


72SM0-74E

Air flow selector (4)

72R0020

Push the air flow selector (4) to changeamong the following functions. The indica-tion of the selected mode appears in thedisplay.

If “AUTO” switch (8) is pushed, the air flowwill vary automatically as the climate con-trol system maintains the selected tem-perature.

VENTILATION (c)

72R0013

Temperature-controlled air comes out ofthe center, side and cup holder outlets.

BI-LEVEL (d)

72R0014

Temperature-controlled air comes out ofthe floor outlets and cooler air comes out

of the center, side and cup holder outlets.When the temperature selector (1) is in thefully cold position or fully hot position, how-ever, the air from the floor outlets and theair from the center, side and cup holderoutlets will be the same temperature.

HEAT (e)

72R0006

Temperature-controlled air comes out ofthe floor outlets and the side outlets, asmall amount of air comes out of the wind-shield defroster outlets and also comesslightly out of the side defroster outlets.

(c)

(d)

(e)

(f)

(c)

(d)

(e)

(f) (4)

EXAMPLE EXAMPLE

EXAMPLE

EXAMPLE

5-7


72SM0-74E

HEAT & DEFROST (f)

72R0007

Temperature-controlled air comes out ofthe floor outlets, the windshield defrosteroutlets, the side defroster outlets and theside outlets.

Defrost switch (5)

72R0008

Push the defrost switch (5) to turn on thedefroster.This is used to clear the windscreen andside windows by pushing the switch whenthe defroster switch is ON, the indicatorlight above the defroster switch will comeON and the defroster display is shown isthe display.

DEFROST

72R0009

Temperature-controlled air comes out ofthe windshield defroster outlets, the sidedefroster outlets and the side outlets.

NOTE:When the defrost switch (5) is pushed toturn on the defroster, the air conditioningsystem will operate and FRESH AIR modewill be selected automatically. In very coldweather, however, the air conditioning sys-tem will not operate.

EXAMPLE

(5)EXAMPLE

EXAMPLE

5-8


72SM0-74E

Air conditioning switch (6)

72R0010

The air conditioning switch (6) is used toturn on and off the air conditioning systemonly when the blower is on. To turn on theair conditioning system, push in the switchand “A/C” will appear in the display. To turnoff the air conditioning system, push in theswitch again and “A/C” will go off.

System Operating Instructions

Automatic operation

72R0011

You can let the climate control systemwork automatically. To set the system forfully-automatic operation, follow the proce-dure below.

1) Start the engine.2) Push “AUTO” switch (8).3) Set the desired temperature by turning

the temperature selector (1).

The blower speed, air intake and air floware controlled automatically to maintain theset temperature. However, the air flow isnot changed to DEFROST position auto-matically.

NOTE:When the recirculated air mode isselected, the automatic operation system

is deactivated even if you push “AUTO”switch (8).

You can use the air conditioning switch (6)to manually turn the air conditioner on oroff according to your preference. Whenyou turn the air conditioning switch off, theclimate control system cannot lower theinside temperature below outside tempera-ture.

To turn the climate control system off, push“OFF” switch (7).

NOTE:If “AUTO” in the display blinks, there is aproblem in the heating system and/or airconditioning system. You should have thesystem inspected by a Maruti Suzukiauthorised workshop.

NOTE:• To find the temperature at which you are

most comfortable, start with the 22°C(72°F) or 25°C (75°F) setting. (the tem-perature vary depending on vehiclespecifications.).

• If you turn the temperature selector (1)until “HI” or “LO” appears on the display,the climate control system will operate atmaximum heating or cooling and theblower will run at full speed.

• To avoid blowing cold air in cold weatheror hot air in hot weather, the system willdelay turning on the blower until warmedor cooled air is available.

(6) EXAMPLE(8) (7) (6) (1)(8) (7) (6) (1)

EXAMPLE

5-9


72SM0-74E

• If your vehicle has been left in the sunwith the windows closed, it will coolfaster if you open the windows briefly.

• Even under the automatic operation, youcan set individual selectors to the man-ual mode. The manually selected func-tions are maintained, and the otherfunctions remain under automatic opera-tion.

• If the windshield and/or the front doorwindows are fogged, push the defrostswitch (5) to turn on the defroster, orpush the air flow selector (4) to changethe air flow to HEAT & DEFROST posi-tion to defog the windows.

• To return the blower speed selector (2),air intake selector (3), and air flow selec-tor (4) to automatic operation, push“AUTO” switch (8).

72R0021

Be careful not to cover the interior tem-perature sensor (10) located between the

steering wheel and the climate controlpanel, or the solar sensor (11) located atthe top of the driver’s side dashboard.These sensors are used by the automaticsystem to regulate temperature.Even if the engine is turned OFF, the tem-perature setting remains in the memory.

Manual operationYou can manually control the climate con-trol system. Set the selectors to thedesired positions.

72R0012

NOTE:If you need maximum defrosting: • push the defrost switch (5) to turn on the

defroster (the air conditioning system willoperate and FRESH AIR mode will beselected automatically),

• set the blower speed selector to high, • adjust the temperature selector to “HI”

indication on the display, and • adjust the side outlets so the air blows

on the side windows.

MaintenanceIf you do not use the air conditioner for along period, such as during winter, it maynot give the best performance when youstart using it again. To help maintain opti-mum performance and durability of your airconditioner, it needs to be run periodically.Operate the air conditioner at least once amonth for one minute with the engineidling. This circulates the refrigerant and oiland helps protect the internal components.

Clean or replace air filter as specified in“Maintenance schedule” in “INSPECTIONAND MAINTENANCE” section. Have thisjob done by a Maruti Suzuki authorisedworkshop as the lower glove box must belowered for this job.

NOTE:Your vehicle uses the air conditioningrefrigerant HFC-134a, commonly called R-134a. R-134a replaced R-12 around 1993for automotive applications. Other refriger-ants are available, including recycled R-12,but only R-134a should be used in yourvehicle.

(11)

(10)

(11)

(10)

EXAMPLE

EXAMPLE

NOTICE

Using the wrong refrigerant maydamage your air conditioning sys-tem. Use R-134a only. Do not mix orreplace the R-134a with other refrig-erants.

5-10


72SM0-74E

Radio Antenna

68KH052

The radio antenna on the roof is remov-able. To remove the antenna, turn it coun-terclockwise. To reinstall the antenna, turnit clockwise firmly by hand.

Installation of Radio Frequency TransmittersWe recommend that you always ask aMaruti Suzuki authorised workshop aboutfrequency band, max output power,antenna position at vehicle and specificconditions for installation and/or use beforeinstalling a radio transmitter in your vehi-cle. Such equipments may cause the elec-tronic control system to malfunction if theyare incorrectly installed or they are notsuited for the vehicle.

Fuel Filler Cap

72SM05004

73R0084

NOTICE

To avoid damage to the radioantenna:• Remove the antenna when using an

automatic car wash.• Remove the antenna when the

antenna hits anything such as alow ceiling in a parking garage orputting a car cover over your vehi-cle.

EXAMPLE EXAMPLE

EXAMPLE

5-11


72SM0-74E

The fuel filler cap is located on the left rearside of the vehicle. The fuel filler door canbe unlocked by pulling up the opener leverlocated on the outboard lower side of thedriver’s seat and locked by simply closingthe door.

57L51093

To remove the fuel filler cap:1) Stop the engine and close all the doors

and windows while refueling.2) Open the fuel filler door.3) Remove the cap by turning it counter-

clockwise.

73R0085

NOTE:The cap holder (1) holds the fuel filler cap(2) by hooking the groove (3) when refuel-ing.

To reinstall the fuel filler cap:1) Turn the cap clockwise until you hear

several clicks.2) Close the fuel filler door.

CAUTION

Remove the fuel filler cap slowly. Thefuel may be under pressure and mayspray out, causing injury.

Open Close

EXAMPLE

WARNING

Fuel is extremely flammable. Do notsmoke when refueling, and makesure there are no open flames orsparks in the area.

(1)

(1)(2)

(1)

(3)

EXAMPLE WARNING

If you need to replace the fuel cap,use a MARUTI SUZUKI genuine cap.Use of an improper cap can result ina malfunction of the fuel system oremission control system. It may alsoresult in fuel leakage while drivingand in the event of an accident.

5-12


72SM0-74E

Engine Hood

73R0086

To open the engine hood:1) Pull the hood release handle located

under the driver’s side instrument panelin the outboard position. This will disen-gage the engine hood lock halfway.

72SM05014

2) Push the under-hood release lever left-ward with your finger, as shown in theillustration. While pushing the lever, liftup the engine hood.

72SM05018

3) While holding the hood, pull the proprod out from the holding clip by protec-tor (1), and then insert the end of therod into the designated hole.

WARNING

• Never allow children to open orclose the hood. Children may injurethemselves because the hood isheavy. Contact with the enginecompartment and related parts maycause burns when this area/theseparts are hot.

• Do not allow children to be near thevehicle when opening the hood.

• Do not leave tools, cloths, andother objects, which were used toclean or perform maintenance andinspections, in the engine compart-ment. Doing so may cause opera-tional failures or even the vehicle tocatch fire when the engine com-partment becomes hot.

EXAMPLE

CAUTION

The release lever and its peripheral,or engine hood can be hot enough toburn your finger right after driving.Touch after those becomes coolenough.

EXAMPLE

NOTICE

Check that the wiper arms are notraised before you lift up the enginehood to avoid damaging the wiperarms and the engine hood.

(1)

EXAMPLE

5-13


72SM0-74E

To close the engine hood:1) Lift the hood up slightly and remove the

prop rod from the hole. Put the prop rodback to the holding clip.

72SM05015

2) Lower the hood to about 20 cm abovethe hood latch, and then let it dropdown. Make sure the hood is securelylatched after closing.

CAUTION

• The prop rod can be hot enough toburn your finger right after driving.Hold the prop rod by protector (1)

• Insert the end of the rod into thehole securely. If the rod slips out,you may get caught in the closinghood.

• The rod may slip out when thehood is blown by wind. Be carefulon windy days.

EXAMPLE WARNING

Make sure the hood is fully closedand latched before driving. If it is not,it can fly up unexpectedly duringdriving, obstructing your view andresulting in an accident.

CAUTION

To avoid injury, check that no part ofthe occupant’s body such as handsor head is in the path of the hoodwhen closing it.

NOTICE

Pushing on the hood from the topmay damage it.

5-14


72SM0-74E

Sun Visor

79J161

The sun visors can be pulled down to blockglare coming through the windshield, orthey can be unhooked and turned to theside to block glare coming through the sidewindow.

Card holder

Type A

74LHT0516

Type B

68PH00509

(1) Card holder(2) Mirror cover

You can put a card in the card holder (1) onthe back of the sun visor.

Vanity mirror (If equipped)

68PH02501

(3) Vanity mirror(4) Vanity mirror light

To use the vanity mirror (3) on the back ofthe sun visor, pull up the mirror cover (2).The vanity mirror light (4) comes on whenthe mirror cover (2) is opened.

NOTICE

When unhooking and hooking a sunvisor, handle it by the hard plasticparts or the sun visor can be dam-aged.

EXAMPLE

(1)

EXAMPLE

(2)(2)

(1)

EXAMPLE

NOTICE

When you park your vehicle outdoorsin direct sunlight or in hot weather,do not leave plastic cards in theholder. The heat may distort them.

(4)

(3)

(4)

(3)

EXAMPLE

5-15


72SM0-74E

Interior Light

Front

72SM05016

Rear

64J211

Interior light switch has three positionswhich function as described below:

ON (1)The light comes on and stays on regard-less of whether the door is open or closed.

NOTE:The light will automatically be turned off toprevent the lead-acid battery from dis-charging when the following conditions aresimultaneously met:• The ignition mode is “LOCK” (OFF). • The hazard warning lights, the position

lights and the headlights are off. • After 15 minutes from the light on.

DOOR (2)• The light comes on when the door is

opened. After closing all doors, the lightwill remain on for 15 seconds and thenfade out. If you press the engine switchto change the ignition mode to “ACC” or“ON” during this time, the light will startto fade out immediately. After pressingthe engine switch to change the ignitionmode to “LOCK” (OFF), the light will turnon for 15 seconds and then fade out.

• When the ignition mode is “LOCK”(OFF), to prevent the lead-acid batteryfrom discharging, the light will automati-cally be turned off when a period of 15minutes has elapsed after any of thedoors (including the tailgate) is openedand other operations are not done.

WARNING

• Do not use the vanity mirror whiledriving. Doing so may result in anaccident due to failure to pay atten-tion to the road in front of you.

• Do not place any weight on orcome to close to the locationswhere an airbag is stored whenusing a vanity mirror. Doing so maycause the airbag to deploy andcause serious injury due to theimpact of the airbag.

NOTICE

If the vanity mirror has the light, donot leave the mirror cover open for along time, or the lead-acid battery willget discharged.

(3)(4) (2) (1) (4)

EXAMPLE

(3) (2) (1)(3) (2) (1)

EXAMPLE

5-16


72SM0-74E

OFF (3)The light remains off even when the door isopened.

SPOT LIGHT (4)When the light switch is in the DOOR orOFF position, push the switch to turn onthe light and push it again to turn off thelight.

73R0091

NOTE:The number of doors involved in the light-ing operation of the interior light dependson the vehicle specification. If there is aswitch (rubber projection) at the dooropening as shown, the door is involved inthe lighting operation. The tailgate is alsoinvolved in this operation even without therubber projection depending on the vehiclespecification.

Accessory Socket

Center console

72SM05005

Floor ConsoleThe accessory socket will work when theignition mode is “ACC” or “ON”.Each socket can be used to provide 12volt/120 watt/10 ampere power for electri-cal accessories when used alone.

72R0047

3rd Row Seats

72R0048

EXAMPLE

EXAMPLE

EXAMPLE

EXAMPLE

5-17


72SM0-74E

Assist Grips

Front Passenger's Seat / 2rd Row Seat

54G249

WARNING

If you pay too much attention to oper-ating the Accessory socket whiledriving, an accident can occur.

CAUTION

All accessory sockets together havea power rating of 120 watt/10 amperecombined. Total load at one time onall ACC sockets should not be morethan 120 watt.

NOTICE

• Use of inappropriate electricalaccessories can cause damage toyour vehicle’s electrical system.Check that any electrical accesso-ries you use are designed to pluginto this type of socket.

• Always close the cap on the socketwhen the socket is not in use.

• When the ignition mode is LOCK(OFF) while using the accessorysocket, the following may occur;– the audio or navigation system

does not turn off.– the keyless entry system does

not work, etc.If they occur, disconnect the itemfrom the accessory socket andcheck whether the electrical equip-ments work properly.If the problem persists, ask aMaruti Suzuki authorised workshopto have the system inspected.

EXAMPLE

5-18


72SM0-74E

3rd Row Seat

73R0094

Assist grips are provided for convenience.

Glove Box

73R0095

To open the glove box, pull the latch lever.To close it, push the lid until it latchessecurely.NOTICE

To avoid damaging the assist gripand the molded headlining, do nothang down the assist grip.

EXAMPLE

WARNING

Never drive with the glove box lidopen. It could cause injury if an acci-dent occurs.

EXAMPLEWARNING

Do not leave cigarette lighters orspray cans in the glove box. If a ciga-rette lighter or spray can is in a placesuch as the glove box, it may lightaccidentally when luggage is loaded,causing a fire.

WARNING

Do not drive the vehicle with the lid ofglove box open.

5-19


72SM0-74E

Overhead Console

72SM05017

Use this stowage to keep small articles.You can open the lid (1) by pressing theraised portion on it.

AUX/USB Socket

72SM05006

Connect your portable digital music player,etc. to this socket to enjoy music throughthe vehicle’s audio system.

(1)

EXAMPLEWARNING

• Do not drive with the overhead con-sole lid open, or the articles stowedinside could fall down during brak-ing, acceleration or in the event ofa collision. Always close the lidafter putting something into or tak-ing something out of the console.

• If you park your vehicle outdoors indirect sunlight or in hot weather,the overhead console can get veryhot since it is close to the roof. So,when parking in such conditions: – Do not leave eyeglasses in the

overhead console. The heat maydistort plastic lenses or frames.

– Do not place flammable items,such as a lighter, in the overheadconsole. The heat may cause afire.

NOTICE

• Do not apply undue force to the lidwhen closing it. Doing so couldbreak the lid and articles inside.

• Place glasses in a case when stow-ing them in the overhead console,or the lenses may be damaged.

NOTICE

Always close the cap when not inuse, since entry of foreign material,dust, water, conductive liquids maydamage the audio system or USBdevice.

WARNING

If you pay too much attention to oper-ating the AUX/USB socket while driv-ing, an accident may occur.

EXAMPLE

5-20


72SM0-74E

Cup Holder and Storage Area

Front

73R0097

Ventilated cup holderIf you turn on the air conditioning system,air flow comes out of the cup holder outlet.Air flow prevent the temperature of thedrink from increasing.Turn the dial wheel (1) clockwise, the cupholder outlet will open. Turn the dial wheel(1) counterclockwise,the cup holder outlet will close.

NOTE:• The temperature of air flow in cup holder

is about the same with the center outlet. • There is no effect to cool the drink in the

cup holder.

3rd Row Seats

73R0098

WARNING

Do not put items in the vehicle thatmay fall or roll around in the vehiclewhile driving. Objects getting caughtin the brake pedal or acceleratorpedal may prevent proper operationof the pedals, which may result in anaccident.

(1)EXAMPLE

EXAMPLE

5-21


72SM0-74E

Bottle Holder

Front seats

73R0099

2nd row seats

73R0100

You should hold a bottle with a cap in theholder.

NOTE:Maruti Suzuki recommends to use maxi-mum 1 liter capacity of bottle.

Front Armrest with Console Box

72R0044

The armrest can be slid forward.

WARNING

Failure to take the precautions listedbelow could cause personal injury orvehicle damage.• Be careful when you are using the

cup holders to hold a cup contain-ing hot liquid. Spilling out hot liq-uid can cause burn injury.In addition, liquids spilling on thelithium-ion battery may cause a fireor electric shock or damage to thebattery.

• Do not use the cup holders to holdsharp-edged, hard, or breakableobjects. Objects in the cup holdersmay be thrown about during a sud-den stop or impact, and couldcause personal injury.

• Be careful not to spill liquid orinsert any foreign materials into themoving part of the gearshift lever,or any electrical components. Liq-uid or foreign materials may dam-age these parts.

• If you spill, or drop liquid acciden-tally, have your vehicle inspectedby a Maruti Suzuki authorisedworkshop.

EXAMPLE

EXAMPLE

NOTICE

To avoid damage to the armrest, donot lean on it or allow a child to sit onit.

EXAMPLE

5-22


72SM0-74E

Console box

72R0045

Use this stowage for keeping small items.Open the compartment by raising the toplid while keeping the lever (1) up.

NOTE:Always close the lid after you put some-thing into or take something out of the box.

Bill/coin Holder

73R0216

Pull the upper portion of the holder, down-ward to open the cover.It is recommended to separate coins (2)and bills (3) with partition.The holder can also be used after slidingout and removing the partition plate (1).Push the upper portion of the holder,upward to close the cover.

(1)

(1)

EXAMPLE

(1)(1)(1)(2)(2)(2)

(3)(3)(3)

EXAMPLE WARNING

Never drive with the bill/coin holderlid open. It could cause injury if anaccident occurs.

5-23


72SM0-74E

Footrest (if equipped)

73R0173

Use the footrest (1) as a support for yourleft foot and body.

Front Seat Back Pocket

72SM05008

This pocket is provided for holding lightand soft things such as gloves, newspa-pers or magazines.

Luggage Box

73R0102

Insert your hands into the notches and liftup the luggage box cover to use the box.

(1)

EXAMPLE

CAUTION

Do not put hard or breakable objectsin the pocket. If an accident occurs,objects such as bottles, cans, etc.can injure the occupants in the rearseat.

EXAMPLE

NOTICE

Do not allow items in the box toextend above the top of the box. Oth-erwise, the box or cover may be dam-aged.

NOTICE

Observe the following instructions,not to break the luggage box cover.• Do not hold open the cover while

driving.• Do not apply any load to the cover

while holding it open.

EXAMPLE

5-24


72SM0-74E

Roof Rail

72SM05019

You can use the roof rails to attach theoptional roof rack. If you use a roof rack,observe the instructions and precautions inthis section.

• Check that the roof rack is securelyinstalled.

• To mount various types of cargo (suchas skis, bicycles, etc.) properly, use suit-able attachments. Install the attach-ments properly and securely. Do notmount cargo directly on the roof panel.The cargo can damage the roof panel.

• The gross weight of the roof rack pluscargo must not exceed the loadingcapacity.– Roof rails: 50 kgAlso, do not let the gross vehicle weight(fully loaded vehicle including driver,passengers, cargo, roof load and trailer

tongue weight) exceed the Gross Vehi-cle Weight Rating (GVWR) listed in the“SPECIFICATIONS” section.

• Mount and secure the cargo onto theroof rack properly. Stow the heaviestitems at the bottom and distribute thecargo as evenly as possible.

• Do not carry large items that hang overthe bumpers or the sides of the vehicle.Otherwise, these items could block yourview.

• Secure the front and rear ends of longitems such as wood panels and surf-boards, to both the front and rear of thevehicle. You should protect the paintedsurfaces of the vehicle from scuffingcaused by tie-down ropes.

• Check periodically that the roof rack issecurely installed and free from damage.

• Roof rack is not the standard accessoryand shall be installed and used in conso-nance with the instructions mentioned inthis manual.

EXAMPLEWARNING

• Abrupt maneuvers or failure toproperly secure cargo can allowthe cargo to fly off the vehicle andhit others, causing personal injuryor property damage.

• Mount cargo securely and avoidabrupt maneuvers such as jackrab-bit starts, sharp turns, fast corner-ing and sudden braking. Checkperiodically that cargo is securelyfastened.

• Large, bulky, long or flat items canaffect vehicle aerodynamics or becaught by the wind, and can reducevehicle control resulting in an acci-dent and personal injury. Drive cau-tiously at a safely reduced speedwhen carrying this type of cargo.

• Non adherence of instructions andprecautions may cause damage toproperty and life of an individual.

5-25


72SM0-74E

Frame HooksIt is not recommended that you use theframe hooks for towing another vehicle.They were originally designed to tow yourvehicle in emergency situation.If your vehicle needs to be towed in anemergency, refer to “Towing your vehicle”in “EMERGENCY SERVICE” section.

Front

72SM05009

The towing eye (1) is provided on the frontof the vehicle for use in emergency situa-tions and sea shipping purpose only.

To install the hook (1), follow the procedurebelow.

52RM50170

1) Pick up the towing eye (1), jack handle(A) and wheel wrench (B) in the lug-gage compartment.

WARNING

Observe the following instructionswhen using frame hooks. The towingeye or vehicle body may break andcause serious injury or damage:• Do not use the frame hooks for

towing another vehicle.• Avoid pulling the vehicle to get out

of severe snowy, muddy or sandyconditions, sudden starts or erraticdriving maneuvers which couldcause excessive stress on the tow-ing eye.

In such case, we recommend thatyou contact a professional service.

NOTICE

To prevent damage to the vehicle,never use the towing eye (1) fortrailer / train shipping.

(1)(1)

EXAMPLE（1）

（A）

（B）

（1）

（A）

（B）

EXAMPLE

5-26


72SM0-74E

72SM05010

2) Remove the cover (C) by using a jackhandle (A) covered with a soft cloth asshown in the illustration.

NOTE:Do not use excessive force as it may dam-age the cover strap.

72SM05011

3) Install the towing eye (1) by hand.

NOTE:It is recommended to secure the cover withtape to prevent damage during towing.

72SM05012

4) To tighten the towing eye (1), turn itclockwise by using a wheel wrench (B)until the towing eye (1) is securelyinstalled.

To remove the towing eye (1), reverse theinstallation procedure.

(A)

(C)

EXAMPLE

(1)

EXAMPLE

(1)

（B）

EXAMPLE

5-27


72SM0-74E

Rear

72SM05013

The frame hook (2) is provided on the rearof the vehicle for use in emergency situa-tions and sea shipping purposes only.

Other Holes

73R0105

The frame holes (3) are provided only fortransporting by a car carrier trailer.

NOTICE

To prevent damage to the vehicle,never use the frame hook (2) fortrailer / train shipping.

(2)((2))

EXAMPLE

NOTICE

Do not use the frame holes (3) fortowing purpose. These holes maybreak and cause serious injury ordamage.

(3) (3)

EXAMPLE

INSPECTION AND MAINTENANCE

6

72RH0-74E

72SM06000

INSPECTION AND MAINTENANCEMaintenance Schedule ....................................................... 6-2Periodic Maintenance Schedule ........................................ 6-2Drive Belt ............................................................................. 6-6Engine Oil and Filter ........................................................... 6-6Engine Coolant .................................................................... 6-10Air Cleaner ........................................................................... 6-11Spark Plugs ......................................................................... 6-12Gear Oil ................................................................................ 6-13Clutch Pedal ........................................................................ 6-14Fuel Filter ............................................................................. 6-14Automatic Transmission (AT) Fluid .................................. 6-15Brakes .................................................................................. 6-16Steering Wheel .................................................................... 6-18Tires ...................................................................................... 6-19Lead-acid Battery ................................................................ 6-21Fuses .................................................................................... 6-23Headlight Aiming ................................................................. 6-27Bulb Replacement ............................................................... 6-27Wiper Blades ....................................................................... 6-31Windshield Washer Fluid ................................................... 6-33Air Conditioning System .................................................... 6-34

6-1


72RH0-74E

72SM03003

WARNING

Take extreme care when working onyour vehicle to prevent accidentalinjury. Carefully observe the follow-ing precautions: • To prevent damage or unintended

activation of the airbag system orseat belt pretensioner system, besure that the lead-acid battery is dis-connected and the ignition modehas been “LOCK” (OFF) for at least90 seconds before performing anyelectrical service work on yourMARUTI SUZUKI vehicle. Do nottouch airbag system components,seat belt pretensioner system com-ponents or wires. The wires are wrapped with yellowtape or yellow tubing, and the cou-plers are yellow for easy identifica-tion.

(Continued)

EXAMPLE WARNING

(Continued)• Do not leave the engine running in

garages or other confined areas.• When the engine is running, keep

hands, clothing, tools, and otherobjects away from the fan and drivebelt. Even though the fan may notbe moving, it can automaticallyturn on without warning.

• When it is necessary to performservice work with the engine run-ning, make sure that the parkingbrake is set fully and the transmis-sion is in Neutral (for manual trans-mission vehicles) or Park (forautomatic transmission vehicles).

• Do not touch ignition wires or otherignition system parts when startingthe engine or when the engine isrunning, or you could receive anelectric shock.

• Be careful not to touch a hotengine, exhaust manifold andpipes, muffler, radiator and waterhoses.

• Do not allow smoking, sparks, orflames around fuel or the lead-acidbattery. Flammable fumes are pres-ent.

(Continued)

WARNING

(Continued)• Do not get under your vehicle if it is

supported only with the portablejack provided in your vehicle.

• Be careful not to cause accidentalshort circuits between the positiveand negative lead-acid battery ter-minals.

• Keep used oil, coolant, and otherfluids away from children and pets.Dispose of used fluids properly;never pour them on the ground,into sewers, etc.

6-2


72RH0-74E

Maintenance ScheduleThe following table shows the times whenyou should perform regular maintenanceon your vehicle. This table shows in kilo-meters and months when you should per-form inspections, adjustments, lubricationand other services.

Periodic MaintenanceSchedule“C”: Clean“R”: Replace or Change“I”: Inspect, clean, adjust, lubricate or replace as necessary“L”: Lubricate“T”: Tighten to Specified Torque“O”: Rotate

NOTE:This table includes services as scheduledup to 80,000 km mileage. Beyond 80,000km, carry out the same services at thesame intervals respectively.

WARNING

MARUTI SUZUKI recommends thatmaintenance on your Maruti Suzukivehicle should be performed by aMaruti Suzuki authorised workshop.

NOTICE

Whenever it becomes necessary toreplace parts on your vehicle, it isrecommended that you use MARUTISUZUKI genuine replacement partsor their equivalent.

6-3


72RH0-74E

Interval: This interval should be judged by odom-eter reading or months, whichever comes first.

FREE INSPECTION PERIODIC MAINTENANCE AT COST

km (x1000) 1 5 10 20 30 40 50 60 70 80

months 1 6 12 24 36 48 60 72 84 96

ENGINE

1-1. Water pump drive belt – – I I I I I I I R

1-2. Engine Coolant (Level, Leakage) l l l R l R l R l R

1-3. Engine oil, engine oil filter and drain plug gasket (Level, Leakage) l l R R R R R R R R

1-4. Cooling system hoses and connections (Leakage and Damage) l l l l l l l l l l

1-5. Engine Mounting & manifold fixing (Loose, Damage) – – I – I – I – I –

1-6. Valve Clearance – – – – I – – I – –

1-7. Exhaust System (Noise, Leakage etc.) – l – l – I – I – l

1-8. Positive Crank Case Ventilation System (Hoses, Connections and Valve) – I – l – I – I – l

IGNITION

2-1. Ignition wire (Damage, Deterioration) – – – l – l – I – l

2-2. Spark Plug – – – – – R – – – R

FUEL

3-1. Air cleaner filter elementPaved-road Clean after every 5,000 KM. Replace after every 40,000 KM.

Dusty Condition Clean after every 2,500 KM or as required. Replace after every 40,000 KM.

3-2. Fuel tank cap, fuel lines and connections (Leakage and Damage) – l – – – l – – – l

3-3. Fuel Filter – – – – – R – – – R

CLUTCH AND TRANSMISSION

4-1. Clutch fluid (Level, Leakage) l l l R l R l R l R

4-2. Clutch slipping (Dragging or Excess Damage) l l l l l l l l l l

4-3. Manual Transaxle Oil (Level, Leakage) l l l l l l l l l l

4-4. Automatic Transaxle Fluid (Level, Leakage) Replace at 1,65,000 km or 11 years whichever comes first

4-5. Hose, Automatic Transaxle Fluid l l l l l l l l l l

4-6. Gear shifter (Operation) l l l l l l l l l l

DRIVE SHAFT

5-1. Drive shaft noise I l l l l l l l l l

5-2. Drive shaft boot (boot damage) – l l l l l l l l l

6-4


72RH0-74E



km (x1000) 1 5 10 20 30 40 50 60 70 80

months 1 6 12 24 36 48 60 72 84 96

BRAKE

6-1. Brake Fluid (Level, Leakage) I I I R I R I R I R

6-2. Brake pedal (Pedal - wall clearance) I I I I I I I I I I

6-3. Parking brake lever and cable (Play, Damage) I I I I I I I I I I

6-4. Brake disc and pad (Wear) – I I I I I I I I I

6-5. Brake drum and shoes (Wear) – – I I I I I I I I

6-6. Brake hoses and pipes (Fluid leakage, Damage) I I I I I I I I I I

6-7. Master cylinder, wheel cylinder and caliper piston (Fluid leakage, Boot/Seal damage) I I I I I I I I I I

WHEEL

7-1. Tires (Air pressure, Abnormal wear, Crack and Rotation) I I&O I&O I&O I&O I&O I&O I&O I&O I&O

7-2. Wheels (Damage) I I I I I I I I I I

7-3. Front/Rear wheel bearing (Loose, Damage) I I I I I I I I I I

FRONT / REAR SUSPENSION

8-1. Suspension strut (Oil leakage, Damage) I I I I I I I I I I

8-2. Suspension arms / Knuckle support and Torsion rods (Loose, Damage) – I I I I I I I I I

8-3. Rear spring (Damage) I I I I I I I I I I

8-4. Shock absorbers (Oil leakage, Damage) I I I I I I I I I I

8-5. All bolts and nuts (Loose) – T T T T T T T T T

STEERING

9-1. Steering wheel (Play, Loose) I I I I I I I I I I

9-2. All rods and arms (Loose, Damage, Wear) I I I I I I I I I I

9-3. Tilt Steering (Operation) I I I I I I I I I I

6-5


72RH0-74E



km (x1000) 1 5 10 20 30 40 50 60 70 80

months 1 6 12 24 36 48 60 72 84 96

ELECTRICAL

10-1. Battery - electrolyte (Level, leakage) and voltage I I I I I I I I I I

10-2. Wiring harness connection (Loose, Damage) – I I I I I I I I I

10-3. Lighting system (Operation, Stains, Damage) I I I I I I I I I I

10-4. Wiper (Operation, Stains, Damage) I I I I I I I I I I

10-5. Horn (Operation) I I I I I I I I I I

10-6. AUX, USB and accessory socket (Operation) – I I I I I I I I I

BODY

11-1. All chassis bolts and nuts (Tighten) – T T T T T T T T T

11-2. All latches, hinges and locks (Function) I I&L I&L I&L I&L I&L I&L I&L I&L I&L

ROAD TEST

12-1. Operation of Brakes, gear shifting and speedometer I I I I I I I I I I

12-2. Body and chassis noise I I I I I I I I I I

AIR CONDITIONER

13-1. Check belt tension I I I I I I I I I I

13-2. Tighten compressor mounting bolt – T T T T T T T T T

13-3. All hose joint (Check, Tighten) I I I I I I I I I I

13-4. Check functioning of Recirculating flap I I I I I I I I I I

13-5. Clean condenser with low pressure water – C C C C C C C C C

13-6. Check belt for frayed edges I I I I I I I I I I

13-7. Check all mounting bolts I I I I I I I I I I

13-8. Air conditioner filter element I I I I R I I R I I

6-6


72RH0-74E

Drive Belt

Check that the drive belt tension is correctwhile the engine is stopped. If the belt istoo loose, insufficient lead-acid batterycharging, engine overheating, poor airconditioning, or excessive belt wear canresult. When you push the belt with yourthumb midpoint between the pulleys, thereshould be a deflection according to the fol-lowing chart.

The belts should also be examined toensure that they are not damaged.

If you need to replace or adjust the belthave it done by a Maruti Suzuki authorisedworkshop.

The drive belts tension is adjusted auto-matically.

Engine Oil and Filter

Specified Oil

72SM06019

(1) Recommended

Check that the engine oil you use comesunder the quality classification of SN.Select the appropriate oil viscosity accord-ing to the above chart.

SAE 0W-16 (1) is the best choice for goodfuel economy and good startability in coldweather.

NOTE:We recommend that you use MARUTISUZUKI genuine oil. To purchase it, visit aMaruti Suzuki authorised workshop.

Oil Level Check

72R0117

72R0118

WARNING

When the engine is running, keephands, hair, clothing, tools, etc. awayfrom the moving fan and drive belts.

-30 -20 -10 0 10 20 30 40-22 -4 14 32 50 68 86 104

(1)5W-30

0W-20

0W-16oCoF

-30 -20 -10 0 10 20 30 40-22 -4 14 32 50 68 86 104

(1)5W-30

0W-20

0W-16oCoF

EXAMPLE

EXAMPLE

UpperLower

EXAMPLE

6-7


72RH0-74E

It is important to keep the engine oil at thecorrect level for proper lubrication of yourvehicle’s engine. Check the oil level withthe vehicle on a level surface. The oil levelindication may be inaccurate if the vehicleis on a slope. The oil level should bechecked either before starting the engineor at least 5 minutes after stopping theengine.The handle of the engine oil dipstick is col-ored with yellow for easy identification.

Pull out the oil dipstick, wipe oil off with aclean cloth, insert the dipstick all the wayinto the engine, then remove it again. Theoil on the stick should be between theupper and lower limits shown on the stick.If the oil level indication is near the lowerlimit, add enough oil to raise the level tothe upper limit.

Refilling

72SM06005

Remove the oil filler cap and pour oil slowlythrough the filler hole to bring the oil level tothe upper limit on the dipstick. Be carefulnot to overfill the oil. Too much oil is almostas bad as too little oil. After refilling, start theengine and allow it to idle for about a min-ute. Stop the engine, wait about 5 minutesand check the oil level again.

Changing Engine Oil and Filter

Drain the engine oil while the engine is stillwarm.

72SM06006

1) Remove the oil filler cap.2) Place a drain pan under the drain plug.3) Using a wrench, remove the drain plug

and drain the engine oil.NOTICE

Failure to check the oil level regularlycould lead to serious engine troubledue to insufficient oil.

CloseOpen

EXAMPLE

CAUTION

The engine oil temperature may behigh enough to burn your fingerswhen the drain plug is loosened. Waituntil the drain plug is cool enough totouch with your bare hands.

Open Close

EXAMPLE

6-8


72RH0-74E

68PH00705

Tightening torque for drain plug 35 Nm (3.6 kg-m, 25.8 lb-ft)

4) Reinstall the drain plug with new gas-ket. Tighten the plug with a wrench tothe specified torque.

Oil Filter Replacement1) Using an oil filter wrench, turn the oil fil-

ter counterclockwise and remove it.2) Using a clean rag, wipe off the mount-

ing surface on the engine where thenew filter will be seated.

3) Smear a small amount of engine oilaround the rubber gasket of the new oilfilter.

4) Screw the new filter by hand until the fil-ter gasket contacts the mounting sur-face.

54G092

(1) Loosen(2) Tighten

WARNING

• Engine oil can be hazardous. Chil-dren and pets may be harmed byswallowing new or used oil. Keepnew and used oil and used oil fil-ters away from children and pets.

• Repeated, prolonged contact withused engine oil may cause skincancer.

• Brief contact with used oil may irri-tate skin.

(Continued)

EXAMPLE WARNING

(Continued)• To minimize your exposure to used

oil, wear a long-sleeve shirt andmoisture-proof gloves (such asdishwashing gloves) when chang-ing oil. If oil contacts your skin,wash thoroughly with soap andwater.

• Launder any clothing or rags if it iswith oil.

• Recycle or properly dispose ofused oil and filters.

(1) (2)(1) (2)

EXAMPLE

6-9


72RH0-74E

Tightening (viewed from filter top)

54G093

(1) Oil filter(2) 3/4 turn

5) Tighten the filter as specified belowfrom the point of contact with themounting surface (or to the specifiedtorque) using an oil filter wrench.

Tightening torque for oil filter

3/4 turn or 14 Nm (1.4 kg-m, 10.3 lb-ft)

Refill with Oil and Oil Leakage Check1) Pour oil through the filler hole and

install the filler cap. For the approximate capacity of the oil,refer to “Capacities” in “SPECIFICA-TIONS” section.

2) Start the engine and carefully check theoil filter and the drain plug for leakage.Run the engine at various speeds for atleast 5 minutes.

3) Stop the engine and wait about 5 min-utes. Check the oil level again and addoil if necessary. Check for leakageagain.

NOTICE

To tighten the oil filter properly, it isimportant to accurately identify theposition at which the filter gasketfirst contacts the mounting surface.

(1)

(2)

(1)

(2)

EXAMPLE

NOTICE

To prevent oil leakage, make surethat the oil filter is tight, but do notover-tighten it.

NOTICE

• When replacing the oil filter, it isrecommended that you use aMARUTI SUZUKI genuine replace-ment filter. If you use an aftermar-ket filter, make sure it is ofequivalent quality and follow themanufacturer’s instructions.

• Oil leakage from the periphery ofthe oil filter or drain plug indicateincorrect installation or gasketdamage. If you find any leakage orare not sure that the filter has beenproperly tightened, have the vehi-cle inspected by a Maruti Suzukiauthorised workshop.

6-10


72RH0-74E

Engine Coolant

Selection of CoolantTo maintain optimum performance anddurability of your engine, use MARUTISUZUKI genuine coolant or equivalent.

This type of coolant is the best for coolingsystem for the following reasons:• The coolant helps maintain proper

engine temperature.• It gives proper protection against freez-

ing and boiling.• It gives proper protection against corro-

sion and rust.

Failure to use the proper coolant can dam-age your cooling system, Maruti Suzukiauthorised workshop can help you selectthe proper coolant.

Coolant Level CheckCheck the coolant level at the reservoirtank, not at the radiator. With the enginecool, the coolant level should be between“FULL” and “LOW” marks.

Adding Coolant

NOTICE

To avoid damaging your cooling sys-tem:• Always use a high quality ethylene

glycol base non-silicate type cool-ant diluted with distilled water atthe correct mixture concentration.

• Check that the proper mix is 30/70and in no case higher than 70/30.Concentrations greater than 70/30coolant to distilled water will causeoverheating conditions.

• Do not use straight coolant norplain water.

• Do not add extra inhibitors or addi-tives. They may not be compatiblewith your cooling system.

• Do not mix different types of basecoolants. Doing so may result inaccelerated seal wear and/or thepossibility of severe overheatingand extensive engine or automatictransmission damage.

WARNING

Swallowing engine coolant can causesevere injury or death. Inhaling cool-ant mist or vapors or getting coolantin your eyes could result in severeinjury.• Do not drink antifreeze or coolant

solution. If swallowed, do notinduce vomiting. Immediately con-tact a poison control center or aphysician.

• Avoid inhaling coolant mist or hotvapors. If inhaled, remove to afresh air area.

• If coolant gets in the eyes, flushwith water and seek medical atten-tion.

• Wash thoroughly after handlingcoolant.

• Keep engine coolant out of thereach of children and pets.

6-11


72RH0-74E

73R0110

If the coolant level is below “LOW” mark,coolant should be added. While the engineis cool, remove the reservoir tank cap andadd coolant until the reservoir tank levelreaches “FULL” mark. Never fill the reser-voir tank above “FULL” mark.

Coolant ReplacementSince special procedures are required, aska Maruti Suzuki authorised workshop forthis job.

Air CleanerIf the air cleaner is clogged with dust, therewill be greater intake resistance, resultingin decreased power output and increasedfuel consumption.

73R0112

1) Unclamp the side clamps and removethe element from the air cleaner case. Ifit appears to be dirty, replace it with anew one.

2) Clamp the side clamps securely.

NOTICE

• The mixture you use should con-tain 50% concentration of anti-freeze.

• If the lowest ambient temperaturein your area is expected to be –35°C (–31°F) or below, use higherconcentrations up to 60% followingthe instructions on the antifreezecontainer.

FULL

LOW

FULL

LOW

EXAMPLE

NOTICE

When putting the cap on the reser-voir tank, line up the mark on the capand the mark on the tank. Failure tofollow this can result in coolant leak-age. EXAMPLE

6-12


72RH0-74E

Spark PlugsFor nickel spark plugs (traditional type):You should inspect spark plugs periodicallyfor carbon deposits. When carbon accu-mulates on a spark plug, a strong sparkmay not be produced. Remove carbondeposits with a wire or pin.

73R0119

To access the spark plug:1) If necessary, disconnect the coupler (1)

while pushing the release lever.2) Remove the ignitor bolts.3) Pull the spark plug boots out.

NOTE:During installation, make sure that thewires, couplers, sealing rubber of aircleaner assy and washers, are correctlyreturned in place.

78K179 60G160S

(1)

EXAMPLE

NOTICE

• When pulling out the ignition coils,do not pull on the cable. Pulling onthe cable can damage it.

• When servicing the iridium/plati-num spark plugs (slender centerelectrode type plugs), do not touchthe center electrode, as it is easy todamage.

Correct Wrong

EXAMPLE

NOTICE

• When installing the spark plugs,screw them in with your fingers toavoid stripping the threads.Tighten the spark plugs with atorque wrench to 17.5 Nm (1.8 kg-m, 13.0 lb-ft). Do not allow contami-nants to enter the engine throughthe spark plug holes when theplugs are removed.

• Never use spark plugs with thewrong thread size.

Loosen

Tighten

EXAMPLE

6-13


72RH0-74E

80G093

Gear Oil

Specified Gear OilWhen adding gear oil, use gear oil with theappropriate viscosity and grade as shownin the chart below.

We highly recommend you use:“MARUTI GEAR OIL 75W” for manualtransmission gear oil.

Manual Transmission oil

54P120706

Gear Oil Level Check

Manual Transmission

60MH047

(1) Oil filler and level plug

To check the gear oil level, use the follow-ing procedure:

1) Park the vehicle on a level surface withthe parking brake applied. Then, stopthe engine.

2) Remove the oil filler and level plug (1).3) If gear oil flows from the plug hole, the

oil level is correct. Reinstall the plug. Ifgear oil does not flow from the plughole, add oil through the filler plug holeuntil oil flows a little from the plug hole.

4) If the oil level is low, add gear oilthrough the oil filler and level plug hole(1) until the oil level reaches the bottomof the filler hole, then reinstall the plug.

NOTICE

When replacing spark plugs, youshould use the brand and type speci-fied for your vehicle. For the speci-fied plugs, refer to“SPECIFICATIONS” section in theend of this book. If you wish to use abrand of spark plug other than thespecified plugs, consult a MarutiSuzuki authorised workshop.

0.95 – 1.05mm (0.037 – 0.041 in.)

EXAMPLE

CFo

o -30-22

-20-4

-1014 32 50 68 86 104

0 10 20 30 40

75W

CFo

o -30-22

-20-4

-1014 32 50 68 86 104

0 10 20 30 40

75W (1)

EXAMPLE

6-14


72RH0-74E

Tightening torque for oil filler andlevel plug (1)Manual Transmission:21 Nm (2.1 kg-m, 15.5 lb-ft)

Gear Oil ChangeSince special procedures, materials andtools are required, ask a Maruti Suzukiauthorised workshop for this job.

Clutch Pedal

Fluid Control Clutch

73R0115

Check the clutch pedal for smooth opera-tion and clutch fluid level from time to time. If clutch dragging is felt with the pedal fullydepressed, have the clutch inspected byyour Maruti Suzuki authorised workshop. Ifthe clutch fluid level is near the “MIN” line,fill it up to the “MAX” line with Maruti Genu-ine Brake Fluid (MGBF) or DOT 3. We highly recommend to use “Maruti Gen-uine Brake Fluid” (MGBF).

Fuel FilterThe fuel filter is located on the way of thefuel hose line under the vehicle body.

72R0124

(1) Fuel filter(2) Fuel inlet hose(3) Fuel outlet hose

Replace the fuel filterSince special procedure are required, werecommend you take your vehicle to aMaruti Suzuki authorised workshop for fuelfilter replacement.

CAUTION

After driving the vehicle, the gear oiltemperature may be high enough toburn you. Wait until the oil filler andlevel plug is cool enough to touchwith your bare hands before inspect-ing gear oil level.

NOTICE

When tightening the plug, apply thefollowing sealing compound orequivalent to the plug threads to pre-vent oil leakage.

MARUTI SUZUKI Bond No. “1216E” or“1217G”

EXAMPLE

(3)

(2)(1)

EXAMPLE

6-15


72RH0-74E

Automatic Transmission (AT) Fluid

Specified FluidUse an automatic transmission fluidSUZUKI AT OIL AW-1.

Fluid Level Check

You must check the fluid level with theautomatic transmission fluid at normaloperating temperature.

To check the fluid level:1) To warm up the transmission fluid, drive

the vehicle or idle the engine until theengine coolant temperature light (bluecolor) goes off.

2) Then drive for ten more minutes.

NOTE:Do not check the fluid level if you have justdriven the vehicle for a long time at highspeed, if you have driven in city traffic inhot weather. Wait until the fluid cools down(about 30 minutes), or the fluid level indica-tion will not be correct.

63J125

3) Park your vehicle on level ground.4) Apply the parking brake and then start

the engine in “P” (Park). Let it idle fortwo minutes and keep it running duringthe fluid level check.

5) With your foot on the brake pedal,move the gearshift lever through eachgear position, pausing for about threeseconds in each position. Then move itback to “P” (Park) position.

80J2071

6) The handle of the A/T fluid dipstick iscolored red for easy identification.Remove the dipstick, wipe the oil offwith a clean cloth and push it back inuntil the cap seats. Then pull out thedipstick.

NOTICE

Driving with too much or too littlefluid can damage the transmission.

NOTICE

Be sure to use the specified auto-matic transmission fluid. Using auto-matic transmission fluid other thanSUZUKI AT OIL AW-1 may damagethe automatic transmission of yourvehicle.

EXAMPLE

WARNING

Be sure to depress the brake pedalwhen moving the gearshift lever, orthe vehicle can move suddenly.

EXAMPLE

6-16


72RH0-74E

7) Check both sides of the dipstick, andread the lowest level. The fluid levelshould be between the two marks in hotrange on the dipstick.

73R0208

(1) FULL HOT(2) LOW HOT(3) The lowest point = Fluid level

8) Add just enough specified fluid throughthe dipstick hole to fill the transmissionoil to the proper level.

Changing OilSince special procedures, materials, andtools are required to change the automatictransmission oil, ask a Maruti Suzukiauthorised workshop for this job.

Brakes

Brake Fluid

73R0116

Check the brake fluid level by looking atthe reservoir in the engine compartment.Check that the fluid level is between “MAX”and “MIN” lines.

NOTICE

After checking or adding oil, be sureto insert the dipstick securely.

EXAMPLE

CH

(3)

(2)

(1)

NOTICE

If your brake fluid level is near “MIN”line, there is a possibility of brakepad and/or shoe wear and brake fluidleakage. Consult with a Maruti Suzukiauthorised workshop regarding thispossibility before filling the reservoir.

EXAMPLE

WARNING

Failure to follow the guidelines belowcan result in personal injury or seri-ous damage to the brake system.• If the brake fluid in the reservoir

drops below a certain level, thebrake warning light on the instru-ment panel will come on (theengine must be running with theparking brake fully disengaged).Should the light come on, immedi-ately ask a Maruti Suzuki autho-rised workshop to inspect thebrake system.

• A rapid fluid loss indicates a leak-age in the brake system whichshould be inspected by a MarutiSuzuki authorised workshop imme-diately.

• Do not use any fluid other thanMaruti Genuine Brake Fluid (MGBF)or DOT3 brake fluid. Do not usereclaimed fluid or fluid that hasbeen stored in old or open contain-ers. It is essential that foreign parti-cles and other liquids are kept outof the brake fluid reservoir.

CAUTION

Brake fluid can harm your eyes anddamage painted surfaces. Use cau-tion when refilling the reservoir.

6-17


72RH0-74E

NOTE:• The fluid level can be expected to gradu-

ally fall as the brake pad and/or shoewear.

• Brake fluid absorbs water over time andbrake fluid with high water content maycause vapor lock or brake system mal-function.Replace your brake fluid in accordancewith the maintenance schedule in yourOwner's Manual.

Brake PedalCheck if the brake pedal stops at the regu-lar height without “spongy” feeling whenyou depress it. If not, have the brake sys-tem inspected by a Maruti Suzuki autho-rised workshop. If you doubt the brakepedal for the regular height, check it as fol-lows:

54G108

Pedal to floor carpet minimum dis-tance “a”: 51 mm (2.0 in.)

With the engine running, measure the dis-tance between the brake pedal and floorcarpet when the pedal is depressed withapproximately 30 kg (66 lbs) of force. Theminimum distance required is as specified.Since your vehicle’s brake system is self-adjusting, there is no need for pedaladjustment. If the pedal to floor carpet distance asmeasured above is less than the minimumdistance required, have your vehicleinspected by a Maruti Suzuki authorisedworkshop.

NOTE:When measuring the distance between thebrake pedal and floor wall, be sure not toinclude the floor mat or rubber on the floorwall in your measurement.

WARNING

Brake fluid is harmful or fatal if swal-lowed, and harmful if it comes in con-tact with skin or eyes. If swallowed,do not induce vomiting. Immediatelycontact a poison control center or aphysician. If brake fluid gets in eyes,flush eyes with water and seek medi-cal attention. Wash thoroughly afterhandling. Solution can be poisonousto animals. Keep out of reach of chil-dren and animals.

“a”“a”

EXAMPLE

6-18


72RH0-74E

72SM06012

Parking Brake

60MHM07001

Ratchet tooth specification “b”: 4th – 9thLever pull force (1):200 N (20 kg, 45 lbs)

Check the parking brake for proper adjust-ment by counting the number of clicksmade by the ratchet teeth as you slowlypull up on the parking brake lever to thepoint of full engagement. The parkingbrake lever should stop between the speci-fied ratchet teeth and the rear wheelsshould be securely locked. If the parkingbrake is not properly adjusted or thebrakes drag is suspected even after thelever has been fully released, have theparking brake inspected and/or adjusted bya Maruti Suzuki authorised workshop.

Steering Wheel

73R0117

Steering wheel play “c”: 0 – 30 mm (0.0 – 1.2 in.)

Check the play of the steering wheel bygently turning it from left to right and mea-suring the distance that it moves beforeyou feel slight resistance. The play shouldbe between the specified values.

Check that the steering wheel turns easilyand smoothly without rattling by turning itall the way to the right and to the left whiledriving very slowly in an open area. If theamount of free play is outside the specifi-cation or you find anything else to bewrong, an inspection must be performedby a Maruti Suzuki authorised workshop.

WARNING

If you experience any of the followingproblems with your vehicle’s brakesystem, have the vehicle inspectedimmediately by a Maruti Suzukiauthorised workshop.• Poor braking performance• Uneven braking (brakes not work-

ing uniformly on all wheels.)• Excessive pedal travel• Brake dragging• Excessive noise

EXAMPLE

(1)

“b”

(1)

“b”

EXAMPLE

“c”“c”

EXAMPLE

6-19


72RH0-74E

Tires

73R0118

The front and rear tire pressure specifica-tions for your vehicle are listed in the tireinformation label. Both front and rear tiresshould have the specified tire pressure.

Tire InspectionInspect your vehicle’s tires at least once amonth or before long trip by performing thefollowing checks:

1) Measure the air pressure with a tiregauge. Adjust the pressure if neces-sary. Remember to check the sparetire, too.

54G136

(1) Tread wear indicator(2) Indicator location mark

2) Check that the depth of the treadgroove is more than 1.6 mm (0.06 in.).To help you check this, the tires havemolded-in tread wear indicators in thegrooves. When the indicators appearon the tread surface, the remainingdepth of the tread is 1.6 mm (0.06 in.)or less and the tire should be replaced.

3) Check for abnormal wear, cracks anddamage. Any tires with cracks or otherdamage should be replaced. If any tiresshow abnormal wear, have theminspected by a Maruti Suzuki autho-rised workshop.

4) Check for loose wheel nuts.5) Check that there are no nails, stones or

other objects sticking into the tires.

EXAMPLEEXAMPLEWARNING

• Air pressures should be checkedwhen the tires are cold or you mayget inaccurate readings.

• Check the inflation pressure fromtime to time while inflating the tiregradually, until the specified pres-sure is obtained.

• Never underinflate or over-inflatethe tires. Underinflation can cause unusualhandling characteristics or cancause the rim to slip on the tirebead, resulting in an accident ordamage to the tire or rim. Overinflation can cause the tire toburst, resulting in personal injury.Overinflation can also causeunusual handling characteristicswhich may result in an accident.

(1)

(2)

EXAMPLE

CAUTION

Hitting curbs and running over rockscan damage tires and affect wheelalignment. Have tires and wheelalignment checked periodically by aMaruti Suzuki authorised workshop.

6-20


72RH0-74E

Tire Rotation

5-tire rotation

80JK040

4-tire rotation

54G114

To avoid uneven wear of your tires and toprolong their life, rotate the tires as illus-trated. Tires should be rotated every 10000km. After rotation, adjust front and rear tirepressures to the specification listed in yourvehicle’s Tire Information Label.

Wheel BalancingIf the vehicle vibrates abnormally onsmooth road, have the wheel balanced atMaruti Suzuki authorised workshop.

Wheel AlignmentIn case of abnormal tire wear or pullingtowards one side, have the wheel alignedat Maruti Suzuki authorised workshop.

Tubeless Tires (If equipped)The vehicle is equipped with TubelessTires. In tubeless tire, a thin layer of butylrubber is used for lining the inside of thetubeless tire. This layer is to prevent airloss and fulfilling the purpose of tube. Theair pressure is maintained by the sealingbetween tire bead and wheel rim. Tubelesstires are having advantage of slow air lossand preventing sudden deflation while driv-ing.

Care and maintenance tips for tubelesstires1) Always maintain recommended infla-

tion pressure. Driving continuously atlow inflation pressure can lead to tiredamage.

2) In case any leakage is found, check forany nail penetration/valve core damageor rim bent. Damaged wheel must notbe used.

3) In case tire has run at low pressure, itmust be inspected for any defect.

4) Whenever new tire is fitted, replace thevalve.

WARNING

• Your MARUTI SUZUKI vehicle isequipped with tires which are allthe same type and size. This isimportant to ensure proper steeringand handling of the vehicle. Nevermix tires of different size or type onthe four wheels of your vehicle. Thesize and type of tires used shouldbe only those approved by MARUTISUZUKI as standard or optionalequipment for your vehicle.

• Replacing the wheels and tiresequipped on your vehicle with cer-tain combinations of aftermarketwheels and tires can significantlychange the steering and handlingcharacteristics of your vehicle.

• Therefore, use only those wheeland tire combinations approved byMARUTI SUZUKI as standard oroptional equipment for your vehi-cle.

NOTICE

Replacing the original tires with tiresof a different size may result in falsespeedometer or odometer readings.Check with a Maruti Suzuki autho-rised workshop before purchasingreplacement tires that differ in sizefrom the original tires.

EXAMPLE

EXAMPLE

6-21


72RH0-74E

5) If continuous high speed driving isrequired, increase pressure of tires by 5psi over recommended inflation pres-sure.

6) Never run the tire beyond TWI (Treadwear indicator). The tire is recom-mended to be replaced when theremaining tread has worn to this point.The indicators are spaced across thetread around the tire marked by a trian-gular symbol (TWI).

7) Always prefer tubeless tire mountingmachine. In case of manual mountingtire/ wheel rim damage may occur.

8) In case of any problem, please get intouch with a Maruti Suzuki authorisedworkshop.

Lead-acid Battery

54G118

For maintenance-free battery (cap-lesstype), you need not add water. For tradi-tional type battery, which has water fillercaps, the level of the battery fluid must bekept between the “MAX” and the “MIN”level lines at all times. You should periodi-cally check the battery, battery terminals,and battery hold-down bracket for corro-sion. Remove corrosion using a stiff brushand ammonia mixed with water, or bakingsoda mixed with water. After removing cor-rosion, rinse with clean water.

If your vehicle is not going to be driven fora month or longer, disconnect the cablefrom the negative terminal of the battery tohelp prevent discharge.

WARNING

• Batteries produce flammablehydrogen gas. Keep flames andsparks away from the lead-acid bat-tery or an explosion may occur.Never smoke when working in thevicinity of the lead-acid battery.

• When checking or servicing thelead-acid battery, disconnect thenegative cable. Be careful not tocause a short circuit by allowingmetal objects to contact the lead-acid battery posts and the vehicleat the same time.

• To avoid harm to yourself or dam-age to your vehicle or lead-acidbattery, follow the jump startinginstructions in “EMERGENCY SER-VICE” section of this manual if it isnecessary to jump-start your vehi-cle.

• Diluted sulfuric acid spilled fromlead-acid battery can cause blind-ness or severe burns. Use propereye protection and gloves. Flusheyes or body with ample water andget medical care immediately if suf-fered. Keep batteries out of reachof children.

MAX

MIN

EXAMPLE

6-22


72RH0-74E

NOTE:The battery liquid is consumed when thebattery is used. If the level is found to beless than the center of upper level “MAX”and lower level “MIN”, add distilled watertill it reaches the upper level line “MAX”.

Replacement of the battery

72RM06006

To remove the battery:1) Disconnect the negative cable (1).2) Disconnect the positive cable (2).3) Remove the retainer nuts (3) and

remove the retainer (4).4) Remove the battery.

To install the battery:1) Install the battery in the reverse order of

removal.2) Tighten the bracket bolt and battery

cables securely.

NOTE:• When the battery is disconnected, some

of the vehicle’s functions will be initial-ized and/or deactivated.These functions are required to be resetafter the battery is reconnected.

• Do not disconnect the battery terminalsfor at least one minute after the engineswitch is pressed to change the ignitionmode to “LOCK” (OFF).

WARNING

If the battery is used with batterylevel being less than the lower levelline “MIN”, it may cause reduced bat-tery life, an exothermic heat, or anexplosion by hydrogen gas occurringfrom the battery. Do not use the bat-tery with battery level being less thanthe lower level line “MIN”.

NOTICE

If the battery liquid is added morethan the upper level line “MAX”, liq-uid may leak by vibrations duringdriving or liquid may spray out insome case depending on the condi-tion of battery charging. These maycause damage to the parts near thebattery. If the battery liquid over-spills, immediatelywash away with water. Do not add thebattery liquid more than the upperlevel line “MAX”.

(1)

(2)

(3)

(4)

EXAMPLE

WARNING

Batteries contain toxic substancesincluding sulfuric acid and lead. Theycould have potential negative conse-quences for the environment andhuman health. Used batteries mustbe disposed of or recycled accordingto applicable rules or regulations andmust not be disposed of with ordi-nary household trash. Make sure notto tip over the battery when youremove it from the vehicle. Other-wise, sulfuric acid could run out andyou might get injured.

NOTICE

Do not use regular battery in ISGVehicle. Use only Exide ConservoN55 battery, else it may deteriorateSmart Hybrid performance.

6-23


72RH0-74E

72SM06007

You may find this label on the inside ofhood.

FusesYour vehicle has three types of fuses, asdescribed below:

Main fuseThe main fuse takes current directly fromthe lead-acid battery.

Primary fusesThese fuses are between the main fuseand individual fuses, and are for electricalload groups.

Individual fusesThese fuses are for individual electrical cir-cuits.

To remove a fuse, use the fuse puller (1)provided in the relay box cover.

Relay box cover

72RM06010

63J095

Fuses in Engine Compartment

73R0195

(1) Main fuse box(2) Relay box

NOTICETHIS VEHICLE USES SPECIAL BATTERY.ONLY USE BATTERY TYPE APPROVED BY THEVEHICLE MANUFACTURER FOR THIS VEHICLE.FOR MORE DETAILS REFER OWNER’S MANUAL.

EXAMPLE

(1)

SpareFuses

(1)

SpareFuses

EXAMPLE

EXAMPLE

(2)(1) (2)2(2(1)

EXAMPLE

6-24


72RH0-74E

Main fuse box

72SM06001

Relay box

72R0115

Sub fuse box

72RM06013

(5)

(4)

(3)

(2)(1)

(6)(5)

(4)

(3)

(2)(1)

(6)

(19)

(12)

(13)

(14)

(15)

(16)

(17)

(18)

(30)

(11)(7)

(8)

(9)

(10)

(31) (32) (33) (34)

(20)

(21)

(23)

(24)

(25)

(26)

(27)

(28)

(29)

(22)

(12)

(14)

(15)

(16)

(17)

(18)

(30)

(31) (32) (33) (34)

(23)

(24)

(25)

(26)

(28)

(29)

(27)

(22)

(21)

(20)

(19)

(13)

(8)

(7)

(11)

(10)(9)

MAIN FUSE / PRIMARY FUSE

(1) – FL1

(2) 100 A FL2

(3) 80 A FL3

(4) 100 A FL4

(5) 50 A FL5

(6) 200 A FL6

(7) 30 A Starting motor

(8) 30 A Blower fan

(9) – Battery

(10) 40 A ABS motor

(11) 40 A Ignition switch

(12) 30 A Back up light

(13) 30 A Sub battery

(14) 20 A Front fog light

(15) – ECM

(35)

Spare

(36)(37)

(35)

Spare

(36)(37)

(16) 25 A ABS solenoid

(17) – Blank

(18) 10 A A/C Compressor

(19) – FI main

(20) 30 A Radiator fan

(21) – Blank

(22) – Blank

(23) 25 A Headlight HI

(24) 15 A Headlight (Left)

(25) 15 A Headlight (Right)

(26) – Fuel pump

(27) 50 A Ignition switch -2

(28) 15 A Auto Transmission

(29) 15 A Fuel Injection

(30) – CNG valve

(31) 15 A Headlight HI (Left)

(32) 15 A Headlight HI (Right)

(33) 5 A Starting Signal

(34) 7.5 A WIP SUB

(35) 25 A Headlight HI

(36) 15 A Headlight HI (Left)

(37) 15 A Headlight HI (Right)

6-25


72RH0-74E

The main fuse, primary fuses and some ofthe individual fuses are located in theengine compartment. If the main fuseblows, no electrical component will func-tion. If a primary fuse blows, no electricalcomponent in the corresponding loadgroup will function. When replacing themain fuse, a primary fuse or an individualfuse, use a MARUTI SUZUKI genuinereplacement parts or equivalent for individ-ual fuses.To remove a fuse, use the fuse puller pro-vided in the fuse box. The amperage ofeach fuse is shown in the back of the fusebox cover and in the relay box.

60G111

NOTE:Make sure that the fuse box always carriesspare fuses.

Fuses under Dashboard

73R0121

80P0185

OK

BLOWN

EXAMPLE

WARNING

If the main fuse or a primary fuseblows, have your vehicle inspectedby a Maruti Suzuki authorised work-shop. Always use a MARUTI SUZUKIgenuine replacement. Never use asubstitute such as a wire even for atemporary repair, or extensive electri-cal damage and a fire can result.

EXAMPLEPRIMARY FUSE

(1) 30 A Power window

(2) 10 A Meter

(3) 15 A Ignition coil

(4) 5 A Ignition-1 signal 2

(5) 20 A Auto Gear Shift lever

(6) 20 A Sunroof motor

(7) – Blank

(8) 20 A Door lock

(9) 15 A Steering lock

(10) 10 A Hazard light

(11) 5 A AUTO-STOP

1 2

15

28

14

27

13

26

3

16

29

4

17

30

5

18

31

6

19

32

7

20

33

8

21

34

9

22

35

10

23

36

11

24

37

12

25

38

6-26


72RH0-74E

81A283

NOTE:According to the vehicle specifications,fuse setting may be different from thespecifications which are shown in theabove tables.

(12) 10 A Rear fog light

(13) 5 A ABS control module

(14) 15 A Rear air conditioner

(15) 5 A Ignition-1 signal 3

(16) 10 A Dome light-2

(17) 5 A Dome light

(18) 15 A Radio

(19) 5 A Controller

(20) 5 A Key2

(21) 20 A Power window timer

(22) 5 A Key

(23) 15 A Horn

(24) 5 A Tail light (Left)

(25) 10 A Tail light

(26) 10 A Airbag

(27) 10 A Ignition-1 signal

(28) 10 A Back up light

(29) 5 A Accessory 3

(30) 20 A Rear defogger

(31) 10 A Mirror heater

(32) 15 A Accessory 2

(33) 5 A Accessory

(34) 10 A Rear wiper

(35) 5 A Ignition-2 signal

(36) 15 A Washer

(37) 25 A Front wiper

(38) 10 A Stop light

BLOWNOK BLOWNOK

EXAMPLE

WARNING

Always replace a blown fuse with afuse of the correct amperage. Neveruse a substitute such as aluminumfoil or wire to replace a blown fuse. Ifyou replace a fuse and the new oneblows in a short period of time, youmay have a major electrical problem.Have your vehicle inspected immedi-ately by a Maruti Suzuki authorisedworkshop.

6-27


72RH0-74E

Headlight AimingSince special procedures are required, aska Maruti Suzuki authorised workshop forthis job.

Bulb Replacement

NOTE:Mist may form on the lenses of exteriorlights (Headlight, Rear combination lightetc.) during or after driving in the rain orafter car washing. This is a natural phe-nomenon which occurs due to temperaturedifference between lamp inside and out-side. Temporary mist on the lens is not amalfunction and will not cause any discom-fort during vehicle driving. The mist would get cleared when the envi-ronmental condition change to sunny orwhen headlamp is kept on. However ifthere is water leakage inside the lamp,contact your Maruti Suzuki authorisedworkshop.

Headlight

72SM06008

Lo beam (1), Hi beam (2) & front position /DRL (3) of headlight unit are of LED typeand non replaceable. It is recommendedthat you take your vehicle to your MarutiSuzuki authorised workshop for replacingthe headlight unit.

Front turn signal light

72SM06009

(4) Front turn signal light

CAUTION

• Light bulbs can be hot enough toburn your finger right after turningoff lights. Replace the bulbs afterthey become cool enough.

• To avoid injury by sharp-edgedparts of the body, wear gloves anda long-sleeved shirt when replacinglight bulbs.

NOTICE

• Frequent bulb replacement indi-cates the need for an inspection ofthe electrical system. This shouldbe carried out by a Maruti Suzukiauthorised workshop.

• During bulb replacement alwaysuse same bulb number as used invehicle.

(1) (2)

(3)

(1) (2)

(3)

EXAMPLE

(4)

EXAMPLE

6-28


72RH0-74E

68PH0073

1) Open the engine hood while the engineis stopped. To remove the bulb holderof the front turn signal light from thelight housing, turn the holder counter-clockwise and pull it out.

72SM06010

(5) Removal(6) Installation

2) To remove and install the bulb of thefront turn signal light (4), simply pull outor push in the bulb.

Side turn signal lightLED is used. It is recommended that youtake your vehicle to a Maruti Suzuki autho-rised workshop for side turn signal lightreplacement.

Rear combination light LED is used for tail light and brake light. Itis recommended that you take your vehicleto a Maruti Suzuki authorised workshop forrear combination light replacement.

72SM06015

(A) Tail light(B) Brake light

72SM06014

With the tailgate opened, remove the bolts(1) and upper tail light (2) gently. Then,press tab (C) of connector and pull it out inarrow direction as shown in the figure.Then, pull the rear combination light (3)firmly to the rearward.

NOTE:When it is difficult to remove the rear com-bination lamp from the body at a low tem-perature (10 deg. C or less), pour waterbetween the body and the rear combina-tion lamp to make the removal smooth.

Front fog lightLED is used. It is recommended that youtake your vehicle to a Maruti Suzuki autho-rised workshop for front fog light replace-ment.

EXAMPLE

(4)(5)

(6)

EXAMPLE

(3)(A)

(2)(1)

(1)

(1)

(1)

(B)

3)((A)

(2)(2(2(1)

(1)

(1)

(1)

(B))

EXAMPLE

(C)(C)

EXAMPLE

6-29


72RH0-74E

Turn light and reverse light

72SM06016

1) To remove the bulb holder of the rearturn signal light (4) or the reversing light(5) from the light housing, turn theholder counterclockwise and pull it out.

72SM06011

(6) Removal(7) Installation

2) To remove the bulb of the rear turn sig-nal light (4) from the bulb holder, pushin the bulb and turn it counterclockwise.To install a new bulb, push it in and turnit clockwise.

3) To remove reversing light (5), pull it outand to install it, push it in arrow direc-tions as shown in figure.

72SM06017

72SM06018

NOTE:When reinstalling the rear combinationlight and upper tail light, check that theclips and connector are properly attached.

(5)(4) (5)(4)

EXAMPLE

(5)

(4)

(6)

(7)0.00.20.40.60.81.0

EXAMPLE EXAMPLE

EXAMPLE

6-30


72RH0-74E

License plate light

73R0211

1) Remove the lens (1) by turning it coun-terclockwise.

73R0192

2) To remove and install the bulb of thelicense plate light (2), simply pull out orpush in the bulb.

High-mount stop lightLED is used. It is recommended that youtake your vehicle to a Maruti Suzuki autho-rised workshop for high-mount stop lightreplacement.

Interior light

Front

72SM06004

Rear

67LH084

Remove the lens by using a flat-bladedscrewdriver covered with a soft cloth asshown. To install it, simply push it back in.The bulb can be removed by simply pullingit out. When replacing the bulb, make surethat the contact springs are holding thebulb securely.

Vanity mirror light

72SM06013

Remove the lens by using a flat-bladedscrewdriver covered with a soft cloth asshown. To install it, simply push it back in.The bulb can be removed by simply pullingit out. When replacing the bulb, make surethat the contact springs are holding thebulb securely.

(1)

EXAMPLE

(2)

EXAMPLE

EXAMPLE

EXAMPLE

EXAMPLE

6-31


72RH0-74E

Wiper Blades

72SM06002

If the wiper blades become brittle or dam-aged, or make streaks when wiping,replace the wiper blades.

To install new wiper blades, follow the pro-cedures below.

NOTE:Some wiper blades may be different fromthe ones described here depending onvehicle specifications. If so, consult aMaruti Suzuki authorised workshop forproper replacement method.

For windshield wipers:

72SM06003

1) Hold the wiper arm away from the win-dow.

NOTE:When raising both of the front wiper arms,pull the driver’s side wiper arm up first.When returning the wiper arms, lower thepassenger’s side wiper arm first. Other-wise, the wiper arms may interfere witheach other.

54G130

2) Squeeze lock (1) towards wiper arm (2)and remove the wiper frame (3) from thearm as shown.

3) Unlock the lock end of the wiper bladeand slide the blade out as shown.

NOTICE

To avoid scratching or breaking thewindow, do not let the wiper armstrike the window while replacing thewiper blade.

EXAMPLEEXAMPLE

(2)

(3)

(3)

(2)

(1)

(1)

EXAMPLE

6-32


72RH0-74E

Removal

60A260

Installation

71LMT0707

(4) Locked end

71LMT0708

(5) Retainer

4) If the new blade is provided without thetwo metal retainers (5), move themfrom the old blade to the new one.

60MH072

(A) Up(B) Down

NOTE:When you install the metal retainers (5),make sure the direction of metal retainersas shown in the above illustrations.

5) Install the new blade in the reverseorder of removal, with the locked end(4) positioned toward the wiper arm. Make sure the blade is properlyretained by all the hooks. Lock theblade end into place.

6) Reinstall wiper frame (3) to wiper arm(2), making sure that the lock lever issnapped securely into the arm.

For rear wipers:

72RM06002

1) Hold the wiper arm away from the win-dow.

EXAMPLE

(4)

(3)

EXAMPLE

(5)

(5)

EXAMPLE

(5)

(A)

(B)

EXAMPLE

EXAMPLE

6-33


72RH0-74E

72RM06003

2) Remove the wiper frame from the wiperarm as shown.

65D151

3) Slide the blade out as shown.

NOTE:Do not flex the wiper blade frame end morethan necessary. If you do, it can break off.

54G135

(1) Retainer

4) If the new blade is provided without thetwo metal retainers, move them fromthe old blade to the new one.

5) Install the new blade in the reverseorder of removal. Make sure the blade is properlyretained by all the hooks.

6) Reinstall wiper frame to arm in thereverse order of removal.

Windshield Washer Fluid

72RM06004

Check that there is washer fluid in the tank.Refill it if necessary. Use a good qualitywindshield washer fluid, diluted with wateras necessary.

EXAMPLE

EXAMPLE

(1)

(1)

EXAMPLE

WARNING

Do not use radiator antifreeze solu-tion in the windshield washer reser-voir. This can severely impairvisibility when sprayed on the wind-shield, and also can damage yourvehicle’s paint.

NOTICE

Damage may result if the washermotor is operated with no fluid in thewasher tank.

EXAMPLE

6-34


72RH0-74E

Air Conditioning SystemIf you do not use the air conditioner for along period, such as during winter, it maynot give the best performance when youstart using it again. To help maintain opti-mum performance and durability of your airconditioner, it needs to be run periodically.Operate the air conditioner at least once amonth for one minute with the engineidling. This circulates the refrigerant and oiland helps protect the internal components.

Air conditioner filter replacementSince special procedures are required, aska Maruti Suzuki authorised workshop forthis job.

73R0201

1) To approach the air conditioner filter,remove the glove box by pressing bothsides of the glove box inward and pull-ing it out.

73R0202

2) Remove the cover (1) and pull out theair conditioner filter (2).

NOTE:When you install a new filter, check thatthe UP mark (3) faces upward.

EXAMPLE

(1)

(2)

(3)

EXAMPLE

EMERGENCY SERVICE

7

72RH0-74E

60G411A

EMERGENCY SERVICETire Changing Tool ............................................................. 7-1Jacking Instructions ........................................................... 7-3Jump-Starting Instructions ................................................ 7-7Towing your vehicle ............................................................ 7-9Engine trouble: Starter does not operate ......................... 7-9Engine trouble: Does not start ........................................... 7-10Engine trouble: Overheating .............................................. 7-10Warning Triangle ................................................................. 7-11

7-1

EMERGENCY SERVICE

72RH0-74E

Tire Changing Tool

61MM0B100

(1) Jack(2) Wheel wrench(3) Jack handle

The tire changing tools are stowed in theside of the luggage compartment. Removethe cover to access the tools.

73R0126

To remove the jack (1), turn its shaft coun-terclockwise by using jack handle (3) andpull the jack out of the storage bracket.

73R0203

NOTE:If you are difficult to use the jack handle(3), use jack handle and wheel wrench (2)as shown in the illustration.

73R0205

To stow the jack, place it in the storagebracket and turn the shaft clockwise withhand.

(3)

(2)

(1)

EXAMPLE

(1)(3)

EXAMPLE

(1)

(3)

(2)

EXAMPLE

EXAMPLE

7-2

EMERGENCY SERVICE

72RH0-74E

73R0206

After temporarily holding the jack (1) until itcontacts the storage bracket, turn the shaft(4) approximately 90° to 180° by using jackhandle (3) to securely hold the jack inplace.

The spare tire is stowed under the rearfloor.

To remove the spare tire:

73R0127

1) Remove the cap and use a wheelwrench to loosen the hook bolt of thespare tire holder. Then, rotate using theend of the jack handle.

73R0128

2) Unhook the spare tire holder and lowerit slowly.

3) Remove the tire.

To install the spare tire:1) Install the spare tire facing up the out-

side of the wheel in the reverse order ofremoval.

2) Tighten the spare tire holder hook boltsecurely.

WARNING

After using the tire changing tools,stow them securely or they cancause injury if an accident occurs.

CAUTION

The jack should be used only tochange wheels. It is important to readthe jacking instructions in this sec-tion before attempting to use thejack.

(1)(3)

(4)

EXAMPLE

NOTICE

Loose the spare tire holder hook boltuntil you can remove the hook byyourself. If the bolt is loosen toomuch, the hook might off and thespare tire might drop off to theground.

Tighten

Loosen

EXAMPLE

WARNING

Do not drive your vehicle with theloose spare tire holder hook bolt, oth-erwise it may come loose or thespare tire may drop off, which canresult in an accident.

EXAMPLE

7-3

EMERGENCY SERVICE

72RH0-74E

Tightening torque for the spare tireholder hook bolt29 Nm (2.8 kg-m, 20.6 lb-ft)

Jacking Instructions

52KM119

1) Place the vehicle on level, hard ground.2) Set the parking brake firmly and shift

into “P” (Park) if your vehicle has anautomatic transmission, or shift into “R”(Reverse) if your vehicle has a manualtransmission.

3) Turn on the hazard warning switch ifyour vehicle is near traffic.

4) Block the front and rear of the wheeldiagonally opposite of the wheel beinglifted.

5) Place the spare tire near the wheelbeing lifted as shown in the illustrationin case the jack slips.

66RM08006

73R0190

NOTICE

Make sure that the spare tire is fixedsecurely. Loosely fixed tire maycause noise during driving. How-ever, do not overtighten the bolt, itmay be warped or broken.

NOTICE

Tighten the spare tire holder hookbolt securely. However, do not over-tighten the bolt, it may be warped orbroken.

WARNING

• Shift into “P” (Park) for an automatictransmission, or into “R” (Reverse)for a manual transmission vehiclewhen you jack up the vehicle.

• Never jack up the vehicle with thetransmission in “N” (Neutral). Oth-erwise, unstable jack may cause anaccident.

EXAMPLE

EXAMPLE

EXAMPLE

7-4

EMERGENCY SERVICE

72RH0-74E

73R0191

6) Position the jack at an angle as shownin the illustration and raise the jack byturning the jack handle clockwise untilthe jack-head groove fits around thejacking bar beneath the vehicle body.

7) Continue to raise the jack slowly andsmoothly until the tire clears theground. Do not raise the vehicle morethan necessary.

Raising vehicle with garage jack• Apply the garage jack to one of the

points indicated below.• Always support the raised vehicle with

jack stands (commercially available) atthe points indicated below.

EXAMPLE WARNING

• Use the jack only to change wheelson level, hard ground.

• Never jack up the vehicle on aninclined surface.

• Never raise the vehicle with thejack in a location other than thespecified jacking point (shown inthe illustration) near the wheel tobe changed.Especially, do not raise the vehiclewith a jack at a part of the torsionbeam which is located under thevehicle body, between rear wheels.

• Make sure that the jack is raised atleast 51 mm (2 inches) before itcontacts the flange. Use of the jackwhen it is within 51 mm (2 inches)of being fully collapsed may resultin failure of the jack.

• Never get under the vehicle when itis supported by the jack.

• Never run the engine when thevehicle is supported by the jackand never allow passengers toremain in the vehicle.

7-5

EMERGENCY SERVICE

72RH0-74E

72R0130

(1)

(1)

(2) (2)(3)

(4)

(5)

(6) (7)

(6)

(4)

(3)

(6)

EXAMPLE(1) Front(2) Jack stand(3) Jacking point for onboard jack(4) Rear(5) Front suspension frame(6) Jacking point for garage jack(7) Application point for two-column lift

and jack stand

NOTE:For more details, please contact a MarutiSuzuki authorised workshop.

NOTICE

• Never apply a garage jack to theexhaust pipe or engine undercoverand rear torsion beam.

• When you apply a garage jack tothe rear jacking point, it may inter-fere with the rear bumper depend-ing on the shape of the garage jack.

7-6

EMERGENCY SERVICE

72RH0-74E

Changing WheelsTo change a wheel, use the following pro-cedure:

1) Remove the jack, tools and sparewheel from the vehicle.

2) Loosen, but do not remove the wheelnuts.

3) Jack up the vehicle (follow the jackinginstructions in this section).

4) Remove the wheel nuts and wheel.

65J4033

5) Clean any mud or dirt off from the sur-face of the wheel (1), hub (2), threadpart (3) and surface of the wheel nuts(4) with a clean cloth. Clean the hubcarefully; it may be hot from driving.

6) Install the new wheel and replace thewheel nuts with their cone shaped endfacing the wheel. Tighten each nutsnugly by hand until the wheel issecurely seated on the hub.

81A057

Tightening torque for wheel nuts100 Nm (10.2 kg-m, 74.0 lb-ft)

7) Lower the jack and fully tighten the nutswith a wheel wrench in numerical orderas shown in the illustration.

WARNING

• Shift into “P” (Park) for an automatictransmission, or into “R” (Reverse)for a manual transmission vehiclewhen you jack up the vehicle.

• Never jack up the vehicle with thetransmission in “N” (Neutral). Oth-erwise, unstable jack may cause anaccident.

(1)

(2)

(3)

(4)

EXAMPLE

WARNING

Use genuine wheel nuts and tightenthem to the specified torque as soonas possible after changing wheels.Incorrect wheel nuts or improperlytightened wheel nuts may comeloose or fall off, which can result inan accident. If you do not have atorque wrench, have the wheel nuttorque checked by a Maruti Suzukiauthorised workshop.

EXAMPLE

7-7

EMERGENCY SERVICE

72RH0-74E

After Changing WheelsStow the tire changing tools (jack, jackhandle and lug wrench) in place. Also,stow the flat tire in the spare tire stowedposition. Refer to “Tire Changing Tool” inthis section.

Jump-Starting Instructions

Jump-Starting1) Use only a 12-volt battery to jump-start

your vehicle. Position the good 12-voltbattery close to your vehicle so that thejump leads will reach both batteries.When using a battery installed onanother vehicle, check that two vehiclesdo not touch each other. Set the park-ing brakes fully on both vehicles.

2) Turn off all vehicle accessories, exceptthose necessary for safety reasons (forexample, headlights or hazard lights).

NOTICE

Repair or replace the flat tire immedi-ately. If the flat tire is placed in thespare tire stowed position for longtime, it can cause vehicle shakiness,noise, or scratches.

WARNING

• Never attempt to jump-start yourvehicle if the lead-acid batteryappears to be frozen. Lead-acidbatteries in this condition mayexplode.

• When making jump lead connec-tions, be certain that your handsand the jump leads remain clearfrom pulleys, belts or fans.

• Batteries produce flammablehydrogen gas. Keep flames andsparks away from the lead-acid bat-tery or an explosion may occur.Never smoke when working nearthe lead-acid battery.

• If the booster lead-acid battery youuse for jump-starting is installed inanother vehicle, make sure the twovehicles are not touching eachother.

• If your lead-acid battery dischargesrepeatedly, for no apparent reason,have your vehicle inspected by aMaruti Suzuki authorised work-shop.

• To avoid harm to yourself or dam-age to your vehicle or lead-acidbattery, follow the jump-startinginstructions below. If you are in doubt, call for qualifiedroad service.

NOTICE

Your vehicle should not be started bypushing or towing. This startingmethod could result in permanentdamage to the catalytic converter.Use jump leads to start a vehicle witha weak or discharged battery.

7-8

EMERGENCY SERVICE

72RH0-74E

73R0199

3) Connect jump leads as follows:

1. Connect one end of the first jumplead to the positive (+) terminal ofthe discharged battery (1).

2. Connect the other end to the positive(+) terminal of the booster battery(2).

3. Connect one end of the second jumplead to the negative (–) terminal ofthe booster battery (2).

4. Make the final connection to anunpainted, heavy metal part(i.e.engine mount bolt (3)) of theengine of the vehicle with the dis-charged battery (1).

4) If the booster battery you are using isfitted to another vehicle, start theengine of the vehicle with the boosterbattery. Run the engine at moderatespeed.

5) Start the engine of the vehicle with thedischarged lead-acid battery.

6) Remove the jump leads in the exactreverse order in which you connectedthem.

(3)

(1)

32

4 1

(2)

EXAMPLE

WARNING

Never connect the jump lead directlyto the negative (–) terminal of the dis-charged lead-acid battery, or anexplosion may occur.

CAUTION

Connect the jump lead to the enginemount bolt securely. If the jump leaddisconnects from the engine mountbolt because of vibration at the startof the engine, the jump lead could becaught in the drive belts.

7-9

EMERGENCY SERVICE

72RH0-74E

Towing your vehicleIf you need to have your vehicle towed,contact a professional service, MarutiSuzuki authorised workshop can provideyou with detailed towing instructions.

2-Wheel Drive (2WD) Automatic TransmissionAutomatic transmission vehicles may betowed using either of the following meth-ods.

1) From the front, with the front wheelslifted and the rear wheels on theground. Before towing, make sure thatthe parking brake is released.

2) From the rear, with the rear wheelslifted and a dolly under the front wheels.

2-Wheel Drive (2WD) Manual Trans-missionManual transmission vehicles may betowed using either of the following meth-ods.

1) From the front, with the front wheelslifted and the rear wheels on theground. Before towing, make sure thatthe parking brake is released.

2) From the rear, with the rear wheelslifted and the front wheels on theground, provided the steering anddrivetrain are in operational condition.Before towing, make sure that trans-mission is in neutral, the steering wheelis unlocked (ignition mode is “ACC”),and the steering wheel is secured witha clamping device designed for towingservice.

Engine trouble: Starter does not operate1) Try pressing the engine switch to

change the ignition mode to “START”with the headlights turned on to deter-mine the lead-acid battery condition. Ifthe headlights go excessively dim or gooff, it usually means that either thelead-acid battery is discharged or thelead-acid battery terminal contact ispoor. Recharge the lead-acid battery orcorrect lead-acid battery terminal con-tact as necessary.

2) If the headlights remain bright, checkthe fuses. If the reason for failure of thestarter is not obvious, there may be amajor electrical problem. Have the vehi-cle inspected by a Maruti Suzuki autho-rised workshop.

NOTICE

Observe the following instructionswhen towing your vehicle.• To help avoid damage to your vehi-

cle during towing, proper equip-ment and towing procedures mustbe used.

• Using the frame hook, tow yourvehicle on paved roads for shortdistances at low speed.

NOTICE

Towing your vehicle with the frontwheels on the ground can result indamage to the automatic transmis-sion.

NOTICE

The steering column is not strongenough to withstand shocks trans-mitted from the front wheels duringtowing. Always unlock the steeringwheel before towing.

7-10

EMERGENCY SERVICE

72RH0-74E

Engine trouble: Does not startMake sure that your vehicle has enoughfuel and lead-acid battery.If the engine does not start under very coldcondition, press the accelerator pedal allthe way to the floor and hold it while crank-ing the engine.Refer to “Starting engine” in operating yourvehicle section.If the engine still does not start have yourvehicle inspected at a Maruti Suzuki autho-rised workshop.Do not operate the starter motor for morethan 12 seconds.

NOTE:If the engine refuses to start, the startermotor automatically stops after a certainperiod of time. After the starter motor hasautomatically stopped or if there is any-thing abnormal in the engine starting sys-tem, the starter motor runs only while theengine switch is held pressed.

Engine trouble: OverheatingThe engine could overheat temporarilyunder severe driving conditions. If the highengine coolant temperature warning lightcomes on as overheating during driving:

1) Turn off the air conditioner.2) Take the vehicle to a safe place and

park.3) Run the engine at a normal idle speed

for a few minutes until the high enginecoolant temperature warning light goesoff.

If the high engine coolant temperaturewarning light does not go off:

1) Turn off the engine and check that thewater pump belt and pulleys are notdamaged or slipping. If any abnormalityis found, correct it.

2) Check the coolant level in the reservoir.If it is found to be lower than “LOW”line, check radiator, water pump andradiator hoses for leakage. If leakagethat may cause overheating is found,do not run the engine until these prob-lems have been corrected.

3) If leakage is not found, carefully addcoolant to the reservoir and then theradiator, if necessary. (Refer to “EngineCoolant” in “INSPECTION AND MAIN-TENANCE” section.)

79J007

WARNING

If you see or hear escaping steam,stop the vehicle in a safe place andimmediately turn off the engine tocool it. Do not open the hood whensteam is present. When the steamcan no longer be seen or heard, openthe hood to see if the coolant is stillboiling. If it is, you must wait until itstops boiling before you proceed.

EXAMPLE

7-11

EMERGENCY SERVICE

72RH0-74E

Warning Triangle

MHO-07-001

In case of vehicle break-down or duringemergency stopping, where, your vehiclecould become a potential traffic hazard,keep the warning triangle, provided withyour vehicle, on the road free from anyobstacles behind your vehicle so as towarn the approaching traffic, at an approxi-mate distance of 50-100 m. The reflectingside of the triangle should face the on com-ing traffic. Please activate the hazardwarning lamps before alighting the vehicleto keep the warning triangle.

MHO-07-014

• Remove the warning triangle carefullyfrom the cover as shown by arrow 1.

• Open both the reflector arms as shownby arrow and lock the arms with eachother with the clip provided in the rightarm. Open the bottom stand in counterclock-wise direction as shown by arrow3. Position the warning triangle behindthe vehicle on a plain surface.

• Reverse the removal procedure forkeeping inside the cover.

• Place the warning triangle below 3rd rowseat.

MHO-07-015

WARNING

• It is hazardous to remove the radia-tor cap when the water temperatureis high, because scalding fluid andsteam may be blown out underpressure. The cap should only betaken off when the coolant tem-perature has lowered.

• To help prevent personal injury,keep hands, tools and clothingaway from the engine cooling fanand air-conditioner fan. These elec-tric fans can automatically turn onwithout warning.

EXAMPLE

EXAMPLE

EXAMPLE

APPEARANCE CARE

8

72RH0-74E

72SM08000

APPEARANCE CARECorrosion Prevention ......................................................... 8-1Vehicle Cleaning ................................................................. 8-2

8-1

APPEARANCE CARE

72RH0-74E

Corrosion PreventionIt is important to take good care of yourvehicle to protect it from corrosion. Listedbelow are instructions for how to maintainyour vehicle to prevent corrosion. Pleaseread and follow these instructions carefully.

Important Information about Corro-sion

Common causes of corrosion1) Accumulation of road salt, dirt, mois-

ture, or chemicals in hard-to-reachareas of the vehicle underbody orframe.

2) Chipping, scratches and any damage totreated or painted metal surfacesresulting from minor accidents or abra-sion by stones and gravel.

Environmental conditions which accel-erate corrosion1) Road salt, dust control chemicals, sea

breeze or industrial pollution will allaccelerate the corrosion of metal.

2) High humidity will increase the rate ofcorrosion particularly when the tem-perature range is just above the freez-ing point.

3) Moisture in certain areas of a vehiclefor an extended period of time may pro-mote corrosion even though other bodysections may be completely dry.

4) High temperatures will cause an accel-erated rate of corrosion to parts of thevehicle which are not well-ventilated topermit quick drying.

This information illustrates the necessity ofkeeping your vehicle (particularly theunderbody) as clean and dry as possible. Itis equally important to repair any damageto the paint or protective coatings as soonas possible.

How to Help Prevent Corrosion

Wash your vehicle frequentlyThe best way to preserve the finish on yourvehicle and to help avoid corrosion is tokeep it clean with frequent washing.Wash your vehicle at least once during thewinter and once immediately after the win-ter. Keep your vehicle, particularly theunderside, as clean and dry as possible.If you frequently drive on salted roads,your vehicle should be washed at leastonce a month during the winter. If you livenear the ocean, your vehicle should bewashed at least once a month throughoutthe year.

For washing instructions, refer to “VehicleCleaning” section.

Remove foreign material depositsForeign material such as salts, chemicals,road oil or tar, tree sap, bird droppings andindustrial fall-out may damage the finish ofyour vehicle if it is left on painted surfaces.Remove these types of deposits as quicklyas possible. If these deposits are difficult towash off, an additional cleaner may berequired. Be sure that any cleaner you useis not harmful to painted surfaces and is

specifically intended for your purposes.Follow the manufacturer’s directions whenusing these special cleaners.

Repair finish damageCarefully examine your vehicle for damageto the painted surfaces. Should you findany chips or scratches in the paint, touchthem up immediately to prevent corrosionfrom starting. If the chips or scratches havegone through to the bare metal, have aqualified body shop make the repair.

Keep passenger and luggage compart-ments cleanMoisture, dirt or mud can accumulateunder the floor mats and may cause corro-sion. Occasionally, check under thesemats to ensure that this area is clean anddry. More frequent checks are necessary ifthe vehicle is used for off-road driving or inwet weather.Certain cargos such as chemicals, fertiliz-ers, cleaners, salts, etc. are extremely cor-rosive by nature. These products shouldbe transported in sealed containers. If theyare spilled or leaked, clean and dry thearea immediately.

8-2

APPEARANCE CARE

72RH0-74E

Park your vehicle in a dry, well-venti-lated areaDo not park your vehicle in a damp, poorlyventilated area. If you often wash yourvehicle in the garage and place it there inwet condition, your garage may be damp.The high humidity in the garage maycause or accelerate corrosion. A wet vehi-cle may corrode even in a heated garage ifthe ventilation is poor.

Vehicle Cleaning

72SM08001

Cleaning Interior

Leather upholsteryRemove loose dirt with a vacuum cleaner.Using a mild soap or saddle soap solution,wipe dirt off with a clean damp soft cloth.To remove soap, wipe the areas again witha soft cloth dampened with water. Wipe theareas dry with a soft dry cloth. Repeat thisuntil the dirt or stain is removed, or use acommercial leather cleaner for tougher dirtor stains. If you use a leather cleaner,carefully follow the manufacturer’s instruc-tions and precautions. Do not use solventtype cleaners or abrasive cleaners.

NOTE:• In order to keep leather upholstery look-

ing good, it should be cleaned at leasttwice a year.

• If leather upholstery becomes wet,immediately wipe it dry with tissue paperor a soft cloth. Water may cause leatherto harden and shrink if it is not wiped off.

• When parking on sunny days, select ashady place or use a sunshade. Ifleather upholstery is exposed to directsunlight for a long time, it may discolorand shrink.

• As is common with natural materials,leather is inherently irregular in grain andcowhide has spots in its natural state.These do not affect the performance ofthe leather in any way.

WARNING

Do not apply additional undercoatingor rust preventive coating on oraround exhaust system componentssuch as the catalytic converter,exhaust pipes, etc. A fire could bestarted if the undercoating substancebecomes overheated.

WARNING

When cleaning the interior or exteriorof the vehicle, do not use flammablesolvents such as lacquer thinners,petrol and benzene. Also, do not usecleaning materials such as bleachesand strong household detergents.The materials could cause personalinjury or damage to the vehicle.

EXAMPLE

8-3

APPEARANCE CARE

72RH0-74E

Vinyl upholsteryPrepare a solution of soap or mild deter-gent mixed with warm water. Apply thesolution to the vinyl with a sponge or softcloth and let it soak for a few minutes toloosen dirt.Rub the surface with a clean, damp clothto remove dirt and the soap solution. Ifsome dirt still remains on the surface,repeat this procedure.

Fabric upholstery (Except front passen-ger seat)Remove loose dirt with a vacuum cleaner.Using a mild soap solution, rub stainedareas with a clean damp cloth. To removesoap, rub the areas again with a clothdampened with water. Repeat this until thestain is removed, or use a commercial fab-ric cleaner for tougher stains. If you use afabric cleaner, carefully follow the manu-facturer’s instructions and precautions.

Fabric upholstery (For front passengerseat)Do not use liquid for cleaning as it maypenetrate the fabric and damage the seatsensor.

Seat beltsClean seat belts with a mild soap andwater. Do not use bleach or dye on thebelts. They may weaken the fabric in thebelts.

Vinyl floor matsOrdinary dirt can be removed from vinylwith water or mild soap. Use a brush tohelp loosen dirt. After the dirt is loosened,rinse the mat thoroughly with water anddry it in the shade.

CarpetsRemove dirt and soil as much as possiblewith a vacuum cleaner. Using a mild soapsolution, rub stained areas with a cleandamp cloth. To remove soap, rub the areasagain with a cloth dampened with water.Repeat this until the stain is removed, oruse a commercial carpet cleaner fortougher stains. If you use a carpet cleaner,carefully follow the manufacturer’s instruc-tions and precautions.

Instrument panel and consoleRemove loose dirt with a vacuum cleaner.Gently wipe dirt off with a tightly squeezeddamp clean cloth. Repeat this until the dirtis removed.

CAUTION



CAUTION



NOTICE

Do not use chemical products thatcontain silicon to wipe electricalcomponents such as the air condi-tioning system, audio, navigationsystem, or other switches. These willcause damage to the components.

8-4

APPEARANCE CARE

72RH0-74E

Cleaning Exterior

Caring for Aluminum Wheels

NOTE:• Do not use an acidic or alkaline deter-

gent, or a cleaner containing petroleumsolvent to wash aluminum wheels.These types of cleaner will cause per-manent spots, discoloration and crackson finished surfaces and damage to cen-ter caps.

• Do not use a bristle brush and soap con-taining an abrasive material. These willdamage finished surfaces.

Washing

Washing by hand

72SM08002

NOTICE

• Liquid such as liquid aromatics,soft drinks or juice may cause dis-coloration, wrinkles, and crackingto resin-based parts and textiles.Immediately wipe it dry with tissuepaper or a soft cloth.

• Do not leave leather products withcolor, fur or vinyl products, etc. inyour vehicle for long periods. Itmay cause discoloration or deterio-ration of interior.

NOTICE

It is important that your vehicle bekept clean and free from dirt. Failureto keep your vehicle clean may resultin fading of the paint or corrosion tovarious parts of the vehicle body.

WARNING

• Never attempt to wash and waxyour vehicle with the engine run-ning.

• When cleaning the underside of thebody and fender, where there maybe sharp-edged parts, wear glovesand a long-sleeved shirt to protectyour hands and arms from beingcut.

• After washing your vehicle, care-fully test the brakes before drivingto make sure they have maintainedtheir normal effectiveness.

EXAMPLE

8-5

APPEARANCE CARE

72RH0-74E

When washing the vehicle, park it in theplace where direct sunlight does not fall onit as much as possible and follow theinstructions below:1) Flush the underside of body and wheel

housings with pressurized water toremove mud and debris. Use plenty ofwater.

2) Rinse the body to loosen the dirt.Remove dirt and mud from the bodyexterior with running water. You mayuse a soft sponge or brush. Do not usehard materials which can scratch thepaint or plastic. Remember that theheadlight covers or lenses are made ofplastic in many cases.

3) Wash the entire exterior with a milddetergent or car wash soap using asponge or soft cloth. The sponge orcloth should be frequently soaked in thesoap solution.

4) Once the dirt has been completelyremoved, rinse off the detergent withrunning water.

5) Wipe off the vehicle body with a wetchamois or cloth and allow it to dry inthe shade.

6) Check carefully for damage to paintedsurfaces. If there is any damage, touchup the damage following the procedurebelow:1. Clean all damaged spots and allow

them to dry.2. Stir the paint and touch up the dam-

aged spots lightly using a smallbrush.

3. Allow the paint to dry completely.

Washing by an automatic car wash

Washing by a high-pressure cleanerNOTICE

When washing the vehicle:• Avoid directing steam or hot water

of more than 80°C (176°F) on plas-tic parts.

• To avoid damaging engine compo-nents, do not use pressurizedwater in the engine compartment.

NOTICE

To avoid damage to the paint or plas-tic surface, do not wipe the dirt offwithout ample water. Follow theabove procedure.

NOTICE

When using a commercial car washproduct, observe the cautions speci-fied by the manufacturer. Never usestrong household detergents orsoaps.

NOTICE

If you use an automatic car wash,make sure that your vehicle’s bodyparts, such as spoilers, cannot bedamaged. If you are in doubt, consultthe car wash operator for advice.

NOTICE

If you use a high-pressure cleaner,keep away the nozzle from your vehi-cle sufficiently.• Bringing the nozzle to your vehicle

too close or pointing the nozzle tothe opening of front grill or bumperetc. can cause damage and mal-function of the vehicle body andparts.

• Pointing the nozzle to the weather-strip of door glasses and doors canallow water to enter the cabin.

8-6

APPEARANCE CARE

72RH0-74E

Waxing

72SM08003

After washing the vehicle, waxing and pol-ishing are recommended to further protectand beautify the paint.

• Only use waxes and polishes of goodquality.

• When using waxes and polishes,observe the precautions specified by themanufacturers.

EXAMPLE

SPECIFICATIONS

9

72RH0-74E

81MM01001

SPECIFICATIONSVehicle Identification .......................................................... 9-1FASTag (if equipped) ........................................................... 9-1High Security Registration Plate (HSRP) .......................... 9-2Fuel ....................................................................................... 9-3SPECIFICATIONS ................................................................ 9-5

9-1

SPECIFICATIONS

72RH0-74E

SPECIFICATIONSVehicle Identification

Chassis Serial Number

73R0135

72SM09001

The chassis and/or engine serial numbersare used to register the vehicle. They arealso used to assist a Maruti Suzuki autho-rised workshop when ordering or referringto special service information. Wheneveryou have occasion to consult a MarutiSuzuki authorised workshop, remember toidentify your vehicle with this number.Should you find the number difficult toread, you will also find it on the identifica-tion plate.

Engine Serial Number

60G128

The engine serial number is stamped onthe cylinder block as shown in the illustra-tion.

FASTag (if equipped)As per Ministry of Road Transport andHighways, the FASTag (1) is mandatory foreach vehicle for the purpose of electronictoll collection or any other purpose as maybe defined by the Government of India.

In case of any damage to FASTag orreplacement of front windscreen, pleasecontact your nearest Maruti Suzuki autho-rised workshop.

72RM09001

EXAMPLE

EXAMPLE

EXAMPLE

(1)EXAMPLE

9-2

SPECIFICATIONS

72RH0-74E

As seen from inside of the vehicle

64MM01002

NOTE:The picture shown is for indicative purposeonly. Internal structure of actual devicemounted on vehicle may be different.

As seen from outside of the vehicle

64MM01003

NOTE:The picture shown is for indicative purposeonly. Internal structure of actual devicemounted on vehicle may be different.

NOTE:• Any attempt to remove the tag from the

windscreen will result in permanent dam-age to the tag.

• Use of chemical cleaners to clean thewindscreen area where the tag ismounted can damage the tag.

• Use of any sharp objects on the tag candamage the tag.

High Security Registration Plate (HSRP)As per Ministry of Road Transport andHighways, every new vehicle must haveHSRP.HSRP contains;• Front and rear HSRP, which will be fitted

with 2 snap-locks each on number platearea.

• Third license plate on front windshield.

Third License Plate

64MM01005

(1) Third license plate

Please do not peel off the tag, as itwould permanently damage the tag!

EXAMPLE

4xxxx xxxx xxxx xxxx xxxx xxxx

Easy to Cruise

EXAMPLE

(1)EXAMPLE

9-3

SPECIFICATIONS

72RH0-74E

Third license plate - As seen from out-side of the vehicle

64MM01008

(a) HSRP issuing authority name (b) Vehicle registration number (c) Unique laser number - Front plate (d) Unique laser number - Rear plate (e) Date of 1st registration (in DD-MM-YYYY format)

NOTE:The picture shown is for indicative purposeonly. Internal structure of actual labelmounted on vehicle may be different.

NOTE:• Any attempt to remove the third license

plate from the windscreen will result inpermanent damage to the label.

• Use of chemical cleaners to clean thewindscreen area where the label ismounted can damage the same.

• Use of any sharp objects on the labelcan damage the label.

• In the event of any replacement of thethird license plate may please contactthe approved authority.

Third license plate - As seen frominside of the vehicle

64MM01009

NOTE:The picture shown is for indicative purposeonly.

NOTE:Color of third license plate (back) is as perHSRP regulation as defined by Ministry ofRoad Transport and highways.

FuelTo avoid damaging catalytic converter, youmust use unleaded petrol with an octanenumber (RON) of 90 or higher.

Petrol/Ethanol blendsBlends of unleaded petrol and ethanol(grain alcohol), also known as gasohol, arecommercially available in certain areas.Blends of this type may be used in yourvehicle if they are no more than 10% etha-nol. Make sure this petrol-ethanol blendhas octane ratings no lower than thoserecommended for the petrol.

NOTE:If you are not satisfied with the driveabilityor fuel economy of your vehicle when youuse a petrol/alcohol blend, you shouldswitch back to unleaded petrol containingno alcohol.

Petrol containing MTBEUnleaded petrol containing MTBE (methyltertiary butyl ether) may be used in yourvehicle if the MTBE content is not greaterthan 15%. This oxygenated fuel does notcontain alcohol.

RXXXXXXXXF R XXXXXXXX::

(a)

(b)

(c) (d)R

( )

) ( )(e) - -

EXAMPLE

It is unlawful for any person to duplicate, alter,change, deface, destroy, multilate, remove, tear down this Third Registration Plate Sticker, except if done by authority of law.Do not wipe with harsh abrasive materials,detergents, etc. as it may deface or damage this Sticker.

NoticeNotice

EXAMPLE

9-4

SPECIFICATIONS

72RH0-74E

NOTICE

The fuel tank has an air space toallow for fuel expansion in hotweather. If you continue to add fuelafter the filler nozzle has automati-cally shut off or an initial blowbackoccurs, the air chamber will becomefull. Exposure to heat when fullyfuelled in this manner will result inleakage due to fuel expansion. Toprevent such fuel leakage, stop fillingafter the filler nozzle has automati-cally shut off, or when initial ventblowback occurs, if using an alterna-tive non-automatic system.

NOTICE

Be careful not to spill fuel containingalcohol while refueling. If fuel isspilled on the vehicle body, wipe it upimmediately. Fuels containing alco-hol can cause paint damage, which isnot covered under the New VehicleLimited Warranty.

9-5

SPECIFICATIONS

72RH0-74E

SPECIFICATIONS

NOTE:Specifications are subject to change without notice.M/T: Manual Transmission A/T: Automatic Transmission

ITEM: Dimensions UNIT: mm

Overall length 4445

Overall width 1775

Overall height 1700

Wheelbase 2740

TrackFront 1510

Rear 1520

ITEM: Mass (weight) UNIT: kg

Curb mass (weight)5M/T 1180

A/T 1190

Gross vehicle mass (weight) rating5M/T 1730

A/T 1740

Permissible maximum Axle Weight

5M/TFront 815

Rear 960

A/TFront 815

Rear 960

9-6

SPECIFICATIONS

72RH0-74E

*1 When battery replacement is necessary, use only N55 (Exide Conservo) battery. Else it may deteriorate performance of Smart Hybridsystem.

*2 If the lithium-ion battery is completely discharged, the battery cannot be recharged. When replacing or disposing the lithium-ionbattery, consult your Maruti Suzuki authorised workshop.

ITEM: Engine

Type K15B (DOHC)

Number of cylinders 4

Bore 74.0 mm

Stroke 85.0 mm

Piston displacement 1462 cm3

Compression ratio 10.5 : 1

ITEM: Electrical

Standard spark plug NGK KR6A-10

Lead-acid battery 12V ISS N55*1

Lithium-ion battery Maintenance free*2

Fuses See “INSPECTION AND MAINTENANCE” section.

9-7

SPECIFICATIONS

72RH0-74E

ITEM: Lights WATTAGE BULB No.

Headlight LED

Turn signal lightFront 12V 21W WY21W

Rear 12V 21W PY21W

Daytime running light (DRL) LED

Position light LED

Side turn signal light (on outside rearview mirror) LED

Tail/brake light LED

License plate light 12V 5W W5W

Reversing light 12V 16W W16W

Interior light 12V 10W –

Front fog light LED

High mount stop light LED

9-8

SPECIFICATIONS

72RH0-74E

*1 If you cannot prepare tires with the specified load index rate and speed symbol, prepare tires with higher load index rate and speedsymbol.

# Spare tire is steel wheel.

NOTE:The spare wheel provided with alloy wheel variant is of steel wheel rim, hence follow 4 tire rotation only. (Refer: Section Inspection andMaintenance)

# The fuel tank capacity is slightly more than the recommended quantity of fuel that you can fill. The additional voluminous space is provided for safety and scientific reasons.

ITEM: Wheels and Tires

Tire size (front, rear and spare#) 185/65R15 88H*1

Rim size 15X5 1/2J

Tire pressures For the specified tire pressure, see the Tire Information Label located on the driver’sdoor lock pillar.

ITEM: Capacities (approx.)

Fuel tank 45 L#

Coolant (including reservoir tank)

M/T See “INSPECTION AND MAINTENANCE”section.

4.7 L

A/T 4.6 L

Engine oil Classification: API SNViscosity: SAE 0W-16 3.1 L (replacement with oil filter)

Transmission oilM/T “MARUTI GENUINE GEAR OIL 75W” 2.6 L

A/T “SUZUKI AT OIL AW-1” 5.0 L

Brake fluid / Clutch fluid MARUTI GENUINE BRAKE FLUID (MGBF) or DOT 3.

Refill to the proper oil level according to the instructions in “INSPECTION AND MAINTENANCE” section.

9-9

SPECIFICATIONS

72RH0-74E

Date post:	29-Mar-2023
Category:	Documents
Upload:	khangminh22
View:	0 times
Download:	0 times

FOREWORD - Team-BHP

Documents