Date: 19 September 2021 Please contact email us: [email protected]with any questions or to enquire for a price. We can offer the following machines subject to remaining unsold: - REF: 37212 BABCOCK STENTER WOVEN, WW 1850 MM, YEAR 2001 BABCOCK STENTER RANGE, GAS HEATED WITH 5 CHAMBERS. WW 1850MM, 2001. TYPE STAR 5301 ECO AIR SUITABLE FOR KNITTED & WOVEN FABRICS PLC CONTROL TYPE BT -15, CENTRE UNWIND, PRE-TENSION ENTRY WITH CENTRALIZING GUIDER AND SCROLL UNIT, BETA 2 BOWL FINISHING PADDER WITH ONBOARD COMPRESSOR ABB AC INVERTER DRIVE, WITH TWO x 1000 LITER SS CHEMICAL MIXING & DOSING TANKS. DM Textile Machinery Ltd is a Limited company registered in the U.K. Registration No: 5667922 VAT No: 880 7188 92 TEL: 01484 460 611 Brooks Mill, Clay Lane, Slaithwaite, Huddersfield, HD7 5BG We have a wide range of Second Hand and Reconditioned Dyeing & Finishing Machines available from stock.
Transcript
Date: 19 September 2021
Please contact email us: [email protected] with any questions or to enquire for a price.We can offer the following machines subject to remaining unsold: -
REF: 37212 BABCOCK STENTER WOVEN, WW 1850 MM, YEAR 2001
BABCOCK STENTER RANGE, GAS HEATED WITH 5 CHAMBERS. WW 1850MM, 2001.TYPE STAR 5301 ECO AIR SUITABLE FOR KNITTED & WOVEN FABRICS PLC CONTROL TYPE BT -15, CENTRE UNWIND, PRE-TENSION ENTRY WITH CENTRALIZING GUIDER AND SCROLL UNIT, BETA 2 BOWL FINISHING PADDER WITH ONBOARD COMPRESSOR ABB AC INVERTER DRIVE, WITH TWO x 1000 LITER SS CHEMICAL MIXING & DOSING TANKS.
DM Textile Machinery Ltd is a Limited company registered in the U.K. Registration No: 5667922 VAT No: 880 7188 92
MAHLO WEFT STRAIGHTENER TYPE RMFC 10A, 4 METER ENTRY TO THE STENTER ENTRY DESK WITH 2 SS DRIVEN SCROLL ROLLERS, OVER FEED, WITH 3 FINGER UN-CURLERS, E+L GUIDERS TYPE FR 5501, HORIZONTAL PIN & CLIP CHAIN, GAS HEATING WITH 5 MAXON VALUE PAK NATURALGAS BURNERS, COMPLETE WITH MAINS GAS TRAIN AND SAFETY VALVE.5 CHAMBERS, WITH PLEVA MOISTURE CONTROL, MAHLO SCANNING BRIDGE TYPE ORTHOPAK. TAKE OFF BY CENTER WIND BATCHER ONTO A FRAMES.
OPTIONAL: We can offer the following machine in factory condition to run in line with the above Babcock stenter, REF: 37219 PAGANINI PALMER CYLINDER 1.800 MM WW YEAR 2001
FELT FINISHING CALENDAR STEAM HEATED TO FIX THE SHRINKAGE ON VARIOUS TYPES OF FABRICS AND DRIES RESIDUAL HUMIDITY, ONE POLISHED FINISH MILD STEEL CYLINDER 1,500 MM DIA MAX TEMP 150 C. ENDLESS NOMEX FELT BLANKETENTRY WITH ADJUSTABLE K-F 20 20 GUIDERS, PATH ROLLERS, FELT GUIDING & TENSIONING ROLLERS, ONE DRYING CYLINDER TO REMOVE CONDENSATION 800 DIA, EXIT VIA LINIER COMPENSATOR AND CONTACT BATCHING ARM, AC INVERTER DRIVES
Video Link: https://youtu.be/u4s3siHH1Us
DM Textile Machinery Ltd is a Limited company registered in the U.K. Registration No: 5667922 VAT No: 880 7188 92
Spurn Point, Manchester Road, Linthwaite, Huddersfield, HD7 5RF
REF: 37223 KRANTZ STENTER KNITS, WW 2200 MM, YEAR 1998
KRANTZ STENTER, 6 CHAMBERS, GAS HEATED MAXON BURNERS, VERTICAL PIN AND CLIP CHAIN, MANUAL WEFT STRAIGHTER WITH SCROLL ROLLERS, LONG ENTRY WITH GUMMING AND E+L TRIMMING UNITS SUITABLE FOR KNITS AND LIGHTWOVEN FABRICS, EXIT WITH COOLING ZONE AND SURFACE BATCHER
REF: 36594 KRANTZ STENTER KNITS, WW 2200 MM, YEAR 1985
FABRIC ENTRY FROM PLAIT OR ROLL WITH SUCTION DEVICE, CORINO DOGAL GUIDING AND SPREADING CENTERING DEVICE, 3 BOWL BETA PADDER (2 RUBBER, 1 STEEL) MAHLO WEFT STRAIGHTENER, PRE-STEAMING DEVICE POSITIONED UNDER THE ENTRY ARMS OF THE TACKLE DEVICE. 5 CHAMBERS HEATED WITH DIATHERMIC OIL, OUPUT COOLING, EDGE DEVICES CUTS AND SUCKS SELVEDGES.EXIT BY PLAITER AND A FRAMES. ELECTRICAL CABINET.
REF: 36236 MONFORTS STENTER KNITS, WW 2200 MM, YEAR 1991
MONFORTS - MONTEX STENTER RANGE -WORKING WIDTH 2200 BABCOCK PADDER WORKING WIDTH 2200MM YEAR 199810 BAYS GAS HEATED OVER FEED WITH E&L UNCURLERS HORIZONTAL PIN CHAIN, MAHLO VMC12 PYROMETERS FITTED, YEAR 2004EXIT WITH COOLING ZONE AND COOLING CYLINDER BIRCH CRUSH CUT EDGE TRIMMING EXIT BY BIRCH NON-STOP CENTREWINDLOW RUNNING HOURS SUITABLE FOR WOVEN & KNITTED FABRICS
REF: 32583 KRANTZ STENTER KNITS, WW 2200 MM, YEAR 1980
KRANTZ STENTER, REFURBISHED IN 1999 AND FITTED WITH NEW BURNERS AND OPERATORS TEMP CONTROLS. 4 CHAMBERS, GAS HEATED, VERTICAL PIN AND CLIP CHAIN, MANUAL WEFT STRAIGHTER WITH SCROLL ROLLERS, LONG ENTRY WITH GUMMING AND TRIMMING SUITABLE FOR KNITS AND WOVEN, EXIT WITH COOLING ZONE, A FRAME BATCHER AND PLAITER
REF: 37006 STENTEX STENTER MULTI LAYER (TENTER), WW 2200 MM, YEAR 1996
STENTEX MULTI LAYER STENTER FRAME, SUITABLE FOR KNITS AND WOVEN FABRICS. ENTRY E+L GUIDERS TYPE FR 1501, OVERFEEDING, PRE STEAMING, 4 CHAMBERS, 6 PASSES GAS HEATED MAXON BURNERS VALUPAK BV, VERTICAL PINCHAIN, GUMMING AND TRIMMING, EXIT BY COOLING ZONE, EXIT BY ROLLER AND A-FRAME.
OPTION WITH PADDER AND WEFT STRAIGHTNERSTENTEX MULTI LAYER STENTER FRAME, HIGH ENTRY WITH BIANCO SCROLL ROLLERS, BIANCO WEFT STRAIGHTENER TYPE DIGITEX, ARTOS BABCOCK 2 BOWL FINISHING PADDER, 2.200 MM WW 12 TON NIP PRESSURE SUITABLE FOR PAD FINISHING ON THE ENTRY TO A STENTER. ADJUSTABLE PRE-TENSION ENTRY WITH CORINO DOGAL CENTRALISING GUIDER WITH 2 DRIVEN SCROLL ROLLERS, TWO PATH ROLLERS, ONE BOW ROLLER.STAINLESS STEEL DIP TANK WITH LEVEL SENSING AND SIDE TANK. NEW CONTROL PANEL WITH ELECTRONIC VARIABLE SPEED DRIVE 11 KWMAIN FRAMES CONSTRUCTED FROM MILD STEEL TOP BOWL 400 MM DIAMETER 80°SHORE HARDNESS NITRILE RUBBER BOTTOM BOWL 400 MM DIAMETER 90° SHORE HARDNESS NITRILE RUBBER, COMPLETE WITH FINE TRIM COMPENSATOR TO SYNCHRONISE WITH ANY TYPE OF DRYING RANGE OR STENTER.
E+L GUIDERS TYPE FR 1501, OVERFEEDING 4 CHAMBERS, 6 PASSES GAS HEATED MAXON BURNERS VALUPAK BV, VERTICAL PIN CHAIN, GUMMING AND TRIMMING, EXIT BY COOLING ZONE, EXIT BY ROLLER AND A-FRAME.
REF: 37107 BABCOCK ARTOS STENTER WOVEN, WW 2000 MM, YEAR 1991
BABCOCK STENTER 2000 MM WORKING WIDTH SUITABLE FOR KNITS & WOVEN FABRIC, PRE TENSION ENTRY WITH GUIDER SYSTEM AND SCROLL ROLLERSBABCOCK 2 BOWL SQUEEZE PADDER MANUAL WEFT STRAIGHTENER,ENTRY CHAIN RAILS WITH E+L FR015 GUIDERS,TANDAMATIC EDGE SPREADERS OVER FEED,NEW AC INVERTER CONTROL PANEL FOR ALL THE DRIVES FITTED IN 2009,HORIZONTAL PIN CHAIN, 10 CHAMBERS THERMAL OIL HEATING SYSTEM,COOLING ZONE TAKE OFF BY PLAITER.
VIDEO:- https://youtu.be/Y4HI9SIuvc0
***As you can see from the photos this machine has been completely inverterised in 2009, this modification alone cost over €50,000 Euros ***
REF: 36938 BABCOCK STENTER WOVEN, WW 1800 MM, YEAR 1989
PRE-TENSION ENTRY FRAMEWORK, BABCOCK 2 BOWL FINISHING PADDER, 1.800 MM WW 12 TON NIP PRESSURE, TOP BOWL 400 MM DIAMETER 100° SHORE HARDNESS STAINLESS STEEL BOTTOM BOWL 400 MM DIAMETER 90° SHORE HARDNESS NITRILE RUBBER COMPLETE WITH FINE TRIM COMPENSATOR LENZE AC INVERTER DRIVE 2009 MAHLO WEFT STRAIGHTENER RFMC9, ENTRY CHAIN 4.5 METERS, E+L UNCURLERS & GUIDERS TYPE FR 1501 OVER FEED WITH LENZE AC INVERTER DRIVES 2009, HEATING 6 CHAMBERS WITH MAXON GAS FIRED BURNERS, THE BURNERS WERE UPGRADED IN 2009 FITTED WITH DOUBLE SOLENOID VALVES TO COMPLY WITH EUROPEAN SAFETY REGULATIONS. 2009HORIZONTAL PIN CHAIN REFURBISHED IN 2009, MAIN DRIVE CHAIN WITH SIEMANS DC DRIVE, COOLING ZONE ON EXIT, TAKE OF BY BATCH ARM/PLAITER LENZE AC INVERTER DRIVE 2009 LENZE AC INVERTER DRIVEN TO A FRAME CENTER WIND. EXAUST SYSTEM WITH AIR MOISTURE CONTRL, FITTED WITH LENZE AC INVERTER,
REF: 36429 FAMATEX STENTER WOVEN, WW 1800 MM, YEAR 1971
PRE-TENSION ENTRY WITH J BOX, HIGH ENTRY WITH E+L KF 10 GUIDERS KUSTER FINISHING PADDER TYPE 222/52, MAHLO WEFT STRAIGHTENER WITH SQUEWING DEVICE. FAMATEX STENTER WITH 5 GAS FIRED HEATING CHAMBERS,ENTRY WITH OPERATORS PLATFORM, ENTRY DESK WITH OVERFEED AND FINGER UN-CURLERS, 3.5-METER-LONG ENTRY CHAIN, HORIZONTAL PIN AND CLIP CHAIN UPGRADED IN 2005 AND FITTED WITH ONE NEW GAS BURNER AND A NEW HEAT RECOVERY SYSTEM, OVERHEAD OPERATORS BRIDGE CONTROLS ON ENTRY DESK. EXIT WITH COOLING ZONE, WITH 60 METER ACCUMULATOR, A FRAME BATCHER AND PLAITER.
REF: 36428 BABCOCK STENTER WOVEN, WW 1800 MM, YEAR 1991
PRE-TENSION ENTRY WITH J BOX, E+L KF20 CENTRALISING GUIDERSBETA 3 BOWL FINISHING PADDER, 1.800 MM WW 15 TON NIP PRESSURE WITH FINE TRIM COMPENSATOR, MAHLO WEFT STRAIGHTENER TYPE RFMC 9 BABCOCK 8 BAY STENTER, TYPE 5000.3800 ECON-AIR, MOUNTED ON A MEZZANINE PLATFORM.ENTRY CHAIN 3 METERS, E+L GUIDERS TYPE FR 1501 OVERFEED 50% +HEATING BY 8 MAXON GAS FIRED BURNERS, HORIZONTAL PIN CHAIN & CLIP. EXIT WITH COOLING ZONE, ACCUMULATOR 40 METRE CLOTH CONTENT TAKE OFF BY DOUBLE NONE STOP BATCHER.
REF: 32856 MONFORTS STENTER WOVEN, WW 2000 MM, YEAR 1990
ENTRY FRAMEWORK WITH BIANCO CENTRALISING GUIDER. MAHLO TYPE RFMC-94H WEFT DETECTION AND STRAIGHTENING UNIT, MONFORT MONTEX STENTER OVEN, YEAR 1990, 2000 MM WORKING WIDTH, MODEL 8G/K, E+L GUIDERS TYPE FR1510 GAS FIRED WITH 4 MAXON BURNERS 4 CHAMBER, HORIZONTAL CLIP/PIN CHAIN, TAKE OFF BY SURFACE BATCHER FOR SMALL ROLLS AND CONTACT BATCHER ONTO A FRAMES.
We look forward to hearing from you soon. In the meantime, should you require further information or additional photographs, please do not hesitate to contact us.
Martin DowneyManaging DirectorDM Textile MachineryE: [email protected]
DM Textile Machinery Ltd is a Limited company registered in the U.K. Registration No: 5667922 VAT No: 880 7188 92
Spurn Point, Manchester Road, Linthwaite, Huddersfield, HD7 5RF
