7/25/2019 01-02 Using the LMT of the GGSN9811
1/24
2Using the LMT of the GGSN9811About This Chapter
This part describes how to start, configure, log in to, and log out of the local maintenance terminal
(LMT) of theGGSN9811.
2.1 Setting the IP Address of the LMT
This part describes how to set the IP address of the LMT by using the example that the LMT
and the GGSN9811 are connected though the local area network (LAN). When the LMT of the
GGSN9811 changes to another network segment, you need to set the IP address of the LMT of
the GGSN9811.
2.2 Connecting the LMT to the GGSN9811This part describes how to connect the local maintenance terminal (LMT) to the GGSN9811 by
taking the local area network (LAN) as an example. When you log in to the LMT for the first
time, you need to perform this operation.
2.3 Starting the LMT
This part describes how to start the local maintenance terminal (LMT).
2.4 Configuring the LMT
This part describes how to configure the local maintenance terminal (LMT), including the
maximum lines of the output messages, whether to automatically lock the LMT, timeout of man-
machine language (MML) commands, output command report to files, and saving of entered
MML commands.
2.5 Setting Office Information
This part describes how to set the office information on the local maintenance terminal (LMT),
including adding, modifying, and deleting an office.
2.6 Locking the LMT
This part describes how to manually lock the local maintenance terminal (LMT). This is to
prevent unauthorized users from logging in to the LMT when the authorized operator is absent.
2.7 Unlocking the LMT
This part describes how to unlock the local maintenance terminal (LMT).
2.8 Running MML Commands
This part describes how to run the man-machine language (MML) commands. The localmaintenance terminal (LMT) of the GGSN9811 provides a man-machine interface based on the
HUAWEI GGSN9811 Gateway GPRS Support Node
Operation Guide 2 Using the LMT of the GGSN9811
Issue 03 (2008-04-10) Huawei Proprietary and Confidential
Copyright Huawei Technologies Co., Ltd
2-1
7/25/2019 01-02 Using the LMT of the GGSN9811
2/24
MML command line. You can configure data for the GGSN9811 through visual and simple
graphic user interfaces (GUIs) to guarantee the normal running of the system.
2.9 Logging Out of the LMT
This part describes how to log out of the local maintenance terminal (LMT) of the
GGSN9811.
2 Using the LMT of the GGSN9811
HUAWEI GGSN9811 Gateway GPRS Support Node
Operation Guide
2-2 Huawei Proprietary and Confidential
Copyright Huawei Technologies Co., Ltd
Issue 03 (2008-04-10)
7/25/2019 01-02 Using the LMT of the GGSN9811
3/24
2.1 Setting the IP Address of the LMT
This part describes how to set the IP address of the LMT by using the example that the LMT
and the GGSN9811 are connected though the local area network (LAN). When the LMT of the
GGSN9811 changes to another network segment, you need to set the IP address of the LMT of
the GGSN9811.
Prerequisite
The new IP address, mask, and default gateway of the LMT are determined.
Context
The principles for configuring the IP address of the LMT is as follows:
l When the LMT and the GGSN9811 are connected through a LAN, the IP address of theLMT must be in the same network segment as the virtual IP address of the external network
of the GGSN9811.
l When the LMT and the GGSN9811 are connected through a router, the IP addresses can
be in different network segments.
Procedure
Step 1 Choose start> Settings> Control Panelon the computer where the LMT is installed. Then,select Network Connections.
Step 2 Select the local connection of the LMT of which the IP address is to reset. Then, right-click andchoose Properties. The Local Area Connection Propertiesdialog box is displayed. Refer to
Figure 2-1.
HUAWEI GGSN9811 Gateway GPRS Support Node
Operation Guide 2 Using the LMT of the GGSN9811
Issue 03 (2008-04-10) Huawei Proprietary and Confidential
Copyright Huawei Technologies Co., Ltd
2-3
7/25/2019 01-02 Using the LMT of the GGSN9811
4/24
Figure 2-1Local area connection properties
Step 3 Select Internet Protocol (TCP/IP)on the Generaltab.
Step 4 Select Internet Protocol (TCP/IP)and click Properties. The Internet Protocol (TCP/IP)Propertiesdialog box is displayed. Refer to Figure 2-2.
2 Using the LMT of the GGSN9811
HUAWEI GGSN9811 Gateway GPRS Support Node
Operation Guide
2-4 Huawei Proprietary and Confidential
Copyright Huawei Technologies Co., Ltd
Issue 03 (2008-04-10)
7/25/2019 01-02 Using the LMT of the GGSN9811
5/24
Figure 2-2Internet Protocol (TCP/IP) properties
Step 5 Select Use the following IP addresson the Generaltab. Set IP addressto ensure that it is inthe same network segment as the virtual IP address of the external network of the GGSN9811.
Set Subnet maskand Default gatewayto be the same as those of the GGSN9811.
Step 6 Select Use the following DNS server addresses. Set the address of the domain name server(DNS) to be the same as that of the GGSN9811.
Step 7 Click OK. The Local Area Connection Propertiesdialog box is displayed. Refer to Figure2-1.
Step 8 Click OKin the Local Area Connection Propertiesdialog box.
----End
2.2 Connecting the LMT to the GGSN9811
This part describes how to connect the local maintenance terminal (LMT) to the GGSN9811 by
taking the local area network (LAN) as an example. When you log in to the LMT for the first
time, you need to perform this operation.
Prerequisite
l The network port of the LMT (or router) is connected to the LAN.
l The communication between the LAN (or router) and the network is normal.
HUAWEI GGSN9811 Gateway GPRS Support Node
Operation Guide 2 Using the LMT of the GGSN9811
Issue 03 (2008-04-10) Huawei Proprietary and Confidential
Copyright Huawei Technologies Co., Ltd
2-5
7/25/2019 01-02 Using the LMT of the GGSN9811
6/24
l The physical connection between the LMT and the GGSN9811 is established.
Context
The computer where the LMT is installed can be connected to the GGSN9811 through the LAN
or router.
Procedure
Step 1 Set the IP address of the LMT. Refer to 2.1 Setting the IP Address of the LMT.
Step 2 Choose start> Runon the LMT. Then, enter cmdin the entry box of Run. Press Enter, andthen the cmd.exewindow is displayed.
Step 3 Enter ping Virtual IP address of external network of the GGSN9811in the cmd.exewindow.
When the following similar information is displayed, it indicates that the communication
between the LMT and the GGSN9811 is normal and the task is complete. Assume that the virtualIP address of the external network of the GGSN9811 is 10.110.42.26.
Pinging 10.110.42.26 with 32 bytes of data:
Reply from 10.110.42.26: bytes=32 time
7/25/2019 01-02 Using the LMT of the GGSN9811
7/24
Condition Operation
The icon of LMT Service Manager exists. It indicates that the LMT Service Manager is
started. Go to Step 2.
The icon of LMT Service Manager does
not exist.
Choose start> Programs> HUAWEI Local
Maintenance Terminalto start the LMT
service manager on the computer where the
LMT is installed. Then, go to Step 2.
Step 2 Choose start > Programs> HUAWEI Local Maintenance Terminal> Local MaintenanceTerminal. The User Logindialog box is displayed. Refer to Figure 2-3.
Start for the First Time? Operation
Yes Go to Step 3.
No Select an office to which the LMT is connected in the Officedrop-
down list box. Go to Step 7.
Figure 2-3User Login
NOTE
l You can also log in to the LMT by clicking Offline. Thus, you can use some functions of the LMT
offline such as help browsing, eliminating the need to log in to the GGSN9811.
l You can log out of the LMT by clicking Exit.
Step 3 Click . The Office Managementdialog box is displayed. Refer to Figure 2-4.
HUAWEI GGSN9811 Gateway GPRS Support Node
Operation Guide 2 Using the LMT of the GGSN9811
Issue 03 (2008-04-10) Huawei Proprietary and Confidential
Copyright Huawei Technologies Co., Ltd
2-7
7/25/2019 01-02 Using the LMT of the GGSN9811
8/24
Figure 2-4Office Management
Step 4 Click Add.... The Adddialog box is displayed.
Step 5 Specify the office name and virtual IP address of the external network of the GGSN9811 in theAdddialog box. Then, click OK. The Office Managementdialog box is displayed. Refer to
Figure 2-5.
Figure 2-5Adding the office
Step 6 Click Closein the Office Managementdialog box. The office configuration is complete. TheUser Logindialog box is displayed. Refer to Figure 2-6.
2 Using the LMT of the GGSN9811
HUAWEI GGSN9811 Gateway GPRS Support Node
Operation Guide
2-8 Huawei Proprietary and Confidential
Copyright Huawei Technologies Co., Ltd
Issue 03 (2008-04-10)
7/25/2019 01-02 Using the LMT of the GGSN9811
9/24
Figure 2-6User Login
Step 7 Enter user name and password, and then click Login. Display the Local MaintenanceTerminal main interface.
NOTE
If the LMT and the GGSN9811 are connected through the M2000 Proxy Server, select Proxy Serverin
the User Logindialog box, and then enter the IP address of the M2000 server.
When logging in to the LMT for the first time, you must log in as an admin user. The password is determined
when the GGSN9811 software is installed.
----End
2.4 Configuring the LMT
This part describes how to configure the local maintenance terminal (LMT), including the
maximum lines of the output messages, whether to automatically lock the LMT, timeout of man-
machine language (MML) commands, output command report to files, and saving of entered
MML commands.
Prerequisite
The Local Maintenance Terminal of the GGSN9811 is started. In addition, the LMT and the
GGSN9811 are connected.
Procedure
l Setting maximum output lines
1. Choose System> System Setting...on the LMT.
2. Set Maximum Output Lineson the Output Windowtab of the System Setting...
dialog box.
NOTE
When the number of the output lines in the output window exceeds the threshold, the earliest
lines are automatically deleted. The latest lines are displayed.
l Setting whether the LMT is automatically locked
1. Choose System> System Setting...on the LMT.
HUAWEI GGSN9811 Gateway GPRS Support Node
Operation Guide 2 Using the LMT of the GGSN9811
Issue 03 (2008-04-10) Huawei Proprietary and Confidential
Copyright Huawei Technologies Co., Ltd
2-9
7/25/2019 01-02 Using the LMT of the GGSN9811
10/24
2. Specify Automatically lockedon the Terminaltab of the System Setting...dialog
box.
NOTE
If the user does not operate the LMT within the specified automatically locked period, the LMT
is automatically locked.
l Setting the MML command timeout
1. Choose System> Command Timeout Setting...on the LMT.
2. Specify the MML Command Timeout(s)in the Command Timeout Settingdialog
box.
NOTE
The MML timeout refers to the period during which the LMT communicates with the
GGSN9811 through MML commands. If the LMT cannot receive the response from the
GGSN9811 within the period, the system sends a prompt.
l Setting the output window
1. Choose System> Output Window Setting...on the LMT.
2. Specify the parameters in the Output Settingarea of the Output Window Setting
dialog box.
NOTE
Some long command reports cannot be displayed in the maintenance output window. The
command output report in a specified period can be saved in the form of a file. This operation
is valid only for the current login.
l Saving input MML commands
1. Choose System> Save Input Command...on the LMT.
2. Specify the parameters in the Save Input Commanddialog box.
NOTE
This function is used to automatically save the MML commands that are executed successfully
or unsuccessfully. By default, the system automatically saves all the commands.
----End
2.5 Setting Office Information
This part describes how to set the office information on the local maintenance terminal (LMT),
including adding, modifying, and deleting an office.
Prerequisite
The LMT is started.
Context
Adding an office refers to establishing a connection between the LMT and the office so that the
office can be managed through the LMT. Modifying an office refers to modifying the office
name and the IP address. Deleting an office refers to deleting the office information on the LMT.
Procedure
l Adding an office
2 Using the LMT of the GGSN9811
HUAWEI GGSN9811 Gateway GPRS Support Node
Operation Guide
2-10 Huawei Proprietary and Confidential
Copyright Huawei Technologies Co., Ltd
Issue 03 (2008-04-10)
7/25/2019 01-02 Using the LMT of the GGSN9811
11/24
1. Choose System > Office Management...on the LMT. The Office Management
dialog box is displayed. Refer to Figure 2-7.
Figure 2-7Office Management
2. Click Add...in the Office Managementdialog box to display the Adddialog box.
Refer to Figure 2-8.
Figure 2-8Adding an office
3. Enter the office name, network element (NE) type, and virtual IP address of the
external network of the GGSN9811.
4. Click OK. The OfficeManagementdialog box is displayed.
5. Click Closein the Office Managementdialog box.
l Modifying an office
1. Choose System > Office Management...on the LMT. The Office Management
dialog box is displayed. Refer to Figure 2-7.
2. Select the office to be modified in the office list of the Office Managementdialog
box. Click Modify...to display the Modifydialog box. Refer to Figure 2-9.
HUAWEI GGSN9811 Gateway GPRS Support Node
Operation Guide 2 Using the LMT of the GGSN9811
Issue 03 (2008-04-10) Huawei Proprietary and Confidential
Copyright Huawei Technologies Co., Ltd
2-11
7/25/2019 01-02 Using the LMT of the GGSN9811
12/24
Figure 2-9Modifying an office
3. Modify the office name, IP address, or NE type.
4. Click OK. The Office Managementdialog box is displayed.
5. Click Closein the Office Managementdialog box.
l Deleting an office
1. Choose System > Office Management...on the LMT. The Office Management
dialog box is displayed. Refer to Figure 2-7.
2. Select the office to be deleted in the office list of the Office Managementdialog box.
Click Delete. Then, a confirmation prompt is displayed.
3. Click Yes. The Office Managementdialog box is displayed.
4. Click Closein the Office Managementdialog box.
----End
2.6 Locking the LMT
This part describes how to manually lock the local maintenance terminal (LMT). This is to
prevent unauthorized users from logging in to the LMT when the authorized operator is absent.
Prerequisite
The LMT is started.
Context
You can lock the LMT of the GGSN9811 in the following ways.
Procedure
l Choose System> Lock.
l Press Ctrl+Alt+M.
l Click on the LMT.
----End
Result
The Terminal Lockedwindow is displayed when the LMT is manually locked.
2 Using the LMT of the GGSN9811
HUAWEI GGSN9811 Gateway GPRS Support Node
Operation Guide
2-12 Huawei Proprietary and Confidential
Copyright Huawei Technologies Co., Ltd
Issue 03 (2008-04-10)
7/25/2019 01-02 Using the LMT of the GGSN9811
13/24
2.7 Unlocking the LMT
This part describes how to unlock the local maintenance terminal (LMT).
Prerequisite
The Terminal Lockedwindow is displayed on the LMT.
Procedure
Step 1 Press Ctrl+Alt+Uin the Terminal Lockedwindow. The Unlock Terminaldialog box isdisplayed.
Step 2 Enter the password, and then click OKto unlock the LMT.
----End
2.8 Running MML Commands
This part describes how to run the man-machine language (MML) commands. The local
maintenance terminal (LMT) of the GGSN9811 provides a man-machine interface based on the
MML command line. You can configure data for the GGSN9811 through visual and simple
graphic user interfaces (GUIs) to guarantee the normal running of the system.
2.8.1 Introduction to MML Commands
Man-machine language (MML) commands are an operational means provided by the localmaintenance terminal (LMT) in addition to the graphic user interface (GUI). The GGSN9811
provides abundant MML commands, with which you can perform overall operation and
maintenance to the system.
2.8.2 Introduction to the MML Command Operation Interface
The man-machine language (MML) command window of the local maintenance terminal (LMT)
consists of the menu, toolbar, status bar, and MML command area. The MML command area is
further divided into the following: the command navigation tree pane, the command display
area, the common maintenance/operation record/help information area, and the command and
parameter input area.
2.8.3 Starting the MML Command Line
This part describes how to start the man-machine language (MML) command line when thecurrent window is not the window of the MML command line. Before running the MML
command, start the GGSN9811 MML command line. When the local maintenance terminal
(LMT) is started, the MML command line is started by default.
2.8.4 Running an MML Command
This part describes how to run a man-machine language (MML) command in the MML
command line. This can facilitate routine configuration and maintenance.
2.8.5 Batching MML Commands
This part describes how to batch the man-machine language (MML) commands. Batching MML
commands refer to that multiple MML commands are executed at one time. You can run the
edited batch files on the local maintenance terminal (LMT), eliminating the need to run an MMLcommand at one time.
HUAWEI GGSN9811 Gateway GPRS Support Node
Operation Guide 2 Using the LMT of the GGSN9811
Issue 03 (2008-04-10) Huawei Proprietary and Confidential
Copyright Huawei Technologies Co., Ltd
2-13
7/25/2019 01-02 Using the LMT of the GGSN9811
14/24
2.8.1 Introduction to MML Commands
Man-machine language (MML) commands are an operational means provided by the local
maintenance terminal (LMT) in addition to the graphic user interface (GUI). The GGSN9811
provides abundant MML commands, with which you can perform overall operation andmaintenance to the system.
The format of MML commands is "action + object", for example, ADD IP. Table 2-1lists the
types of actions.
Table 2-1Description of MML commands action types
Abbreviation Meaning
ACT Activate
ADD Add
BCK Dump manually
BKP Back up
CLR Clear
CON Confirm
CPY Copy
CRE Create
DEA Deactivate, close, or disable
DEL Delete
DLD Download
DSP Display
EXP Export
FMT Format
FOC Forcibly obtain
LCK Lock
LOD Load
LST List
MOD Modify
MOV Move
REF Refresh
REQ Request
RMV Remove
2 Using the LMT of the GGSN9811
HUAWEI GGSN9811 Gateway GPRS Support Node
Operation Guide
2-14 Huawei Proprietary and Confidential
Copyright Huawei Technologies Co., Ltd
Issue 03 (2008-04-10)
7/25/2019 01-02 Using the LMT of the GGSN9811
15/24
Abbreviation Meaning
RST Reset
RTR Restore
SAV Save
SET Set
STP Stop
STR Start
SWP Swap, and forcibly switch over
SYN Synchronize
ULD Upload
ULK Unlock
UPD Upgrade
VRF Verify
The syntax structure of an MML command is divided into three parts: the command keyword,
parameter, and parameter value. For example:
ADD IP: INTFN="ethernet1/0/0", IPADDR="10.10.10.1", MASK="255.255.255.0";
Here, the character string ADD IPbefore ":" is the keyword of the command; INTFN,
IPADDR, and MASKbefore "=" are parameters, which are separated by ","; ethernet1/0/0,
10.10.10.1, and 255.255.255.0behind "=" are parameter values. The whole command ends with
";".
2.8.2 Introduction to the MML Command Operation Interface
The man-machine language (MML) command window of the local maintenance terminal (LMT)
consists of the menu, toolbar, status bar, and MML command area. The MML command area is
further divided into the following: the command navigation tree pane, the command display
area, the common maintenance/operation record/help information area, and the command and
parameter input area.
HUAWEI GGSN9811 Gateway GPRS Support Node
Operation Guide 2 Using the LMT of the GGSN9811
Issue 03 (2008-04-10) Huawei Proprietary and Confidential
Copyright Huawei Technologies Co., Ltd
2-15
7/25/2019 01-02 Using the LMT of the GGSN9811
16/24
Figure 2-10GUI of the LMT
When you use MML commands to configure data, the following interfaces are involved: the
command navigation tree pane, the command window, and the output window. Refer to Figure
2-10. The MML command window includes areas (5), (6), and (7). Refer to Figure 2-10. By
default, the output window is hidden, and it is mainly used to display the detailed information
when the command is executed. For details, see the following description.
MML Command Navigation Tree
On the system menu of the LMT, choose View > Navigation Tree, or click on the toolbar
to display the navigation tree pane. Refer to Figure 2-11. In the navigation tree pane, there are
three tabs: Maintenance, MML Command, and Device Panel. Here, the MML Command
tab contains two subtabs: Navigation Treeand Search.
l On the MML Commandtab, select the Navigation Treesubtab to display the MML
command navigation tree. Select the Maintenancetab to display the maintenance
navigation tree. Select the Device Paneltab to display the device panel navigation tree.
The navigation tree displays the logical structure of system configuration and maintenance
as well as all the MML commands.
l On the MML Commandtab, select the Searchsubtab to display the MML commandsearch page. To search a command, enter a keyword in the search page.
2 Using the LMT of the GGSN9811
HUAWEI GGSN9811 Gateway GPRS Support Node
Operation Guide
2-16 Huawei Proprietary and Confidential
Copyright Huawei Technologies Co., Ltd
Issue 03 (2008-04-10)
7/25/2019 01-02 Using the LMT of the GGSN9811
17/24
Figure 2-11MML Commandtab
MML Command Window
To open the MML command window, you can choose View > Command Windowon the
menu, click on the toolbar, double-click a command on the Navigation Treetab, or press
F4. Areas (5), (6), and (7) as shown in Figure 2-10are all in the command window.
Three areas of the command window from top to bottom are as follows: the Common
Maintenance/Operation Record/Help Information area, the command display area, and the
command and parameter input area. Their functions are as follows:
l Common maintenance/operation record/help information area: Three tabs are included to
respectively display execution results of the command, record history commands, and
provide command help information. The Help Information area details the command
function, precautions, meaning of each parameter, and examples of the commands.
l Command display area: It is used to display the complete configuration command.
l Command and parameter input area: It is used for entering the command parameters one
by one based on the prompt of the parameter name.
NOTE
In the command and parameter input area, red parameters are compulsory, and you must type or select a
parameter value; black parameters are optional, and you can type or select a parameter value based on your
actual requirements.
Table 2-2describes the four key shortcut icons in the command and parameter input area.
HUAWEI GGSN9811 Gateway GPRS Support Node
Operation Guide 2 Using the LMT of the GGSN9811
Issue 03 (2008-04-10) Huawei Proprietary and Confidential
Copyright Huawei Technologies Co., Ltd
2-17
7/25/2019 01-02 Using the LMT of the GGSN9811
18/24
Table 2-2Shortcut icons in the command and parameter input area
Shortcut Icon Meaning
Goes to the parameter input interface. you can also go to the
parameter input interface by pressing Enterafter entering thecommand.
Runs a command. You can also run a command by pressing F9.
Selects the next command. You can also select the next command
by pressing F8.
Selects the previous command. You can also select the previous
command by pressing the F7key.
MML Command Output WindowTo open the output window, you can choose View > Output Windowon the menu, or click
on the toolbar, and then the output window appears on the status bar automatically. Refer
to Figure 2-12.
Figure 2-12Output window
By default, the output window is hidden. It is mainly used to display the detailed return
information when the MML command is executed.
Inputting the Command Keyword
You can enter the command keyword in the following ways.
l Locate the command by double-clicking Set IP address (ADD IP)in the MML command
navigation tree.
l Directly type the command keyword ADD IPin the Command Inputfield of the command
window, and then click the icon or press Enter. When you type one or more letters of
a command keyword, the system searches all commands initiated by the letter(s) in the
alphabetical sequence. The first command in the sequence is displayed in the input field.
l If you remember only part of the keyword, you can search the complete keyword in the
Search tab.
Running the Command
After configuring all the parameters, click to run this command. You can view the execution
result from the Common Maintenancepage in the output window.
If only the command keyword is provided, the earlier mentioned three steps are applicable toall data configuration commands of the GGSN9811. Therefore, for data configuration hereafter
2 Using the LMT of the GGSN9811
HUAWEI GGSN9811 Gateway GPRS Support Node
Operation Guide
2-18 Huawei Proprietary and Confidential
Copyright Huawei Technologies Co., Ltd
Issue 03 (2008-04-10)
7/25/2019 01-02 Using the LMT of the GGSN9811
19/24
in this document, only the keywords of the commands are given in the table. Refer to Table
2-3.
Table 2-3Setting IP addresses
Command Function
ADD IP Set the interface IP address
2.8.3 Starting the MML Command Line
This part describes how to start the man-machine language (MML) command line when the
current window is not the window of the MML command line. Before running the MML
command, start the GGSN9811 MML command line. When the local maintenance terminal
(LMT) is started, the MML command line is started by default.
Prerequisite
The LMT is started.
Procedure
Step 1 Click the MML Commandtab at the lower left part of the navigation tree pane on the LMT.Display the Navigation Treepane.
Step 2 Double-click MML Commandin the Navigation Treepane to start the MML command line.
----End
2.8.4 Running an MML Command
This part describes how to run a man-machine language (MML) command in the MML
command line. This can facilitate routine configuration and maintenance.
Prerequisite
l The LMT is started and the GGSN9811 is connected.
l The MML command line is started.
l If the configuration commands need to be executed, ensure that the right to configure the
commands is granted.
Context
You can run an MML command in the following ways.
l Enter the MML command in the Command Input (F5)box.
l Select the MML command in the History Commandbox.
l Copy the MML command scripts to the command input area.
l Select the MML command in the MML Commandof the navigation tree.
HUAWEI GGSN9811 Gateway GPRS Support Node
Operation Guide 2 Using the LMT of the GGSN9811
Issue 03 (2008-04-10) Huawei Proprietary and Confidential
Copyright Huawei Technologies Co., Ltd
2-19
7/25/2019 01-02 Using the LMT of the GGSN9811
20/24
Procedure
l Entering the MML command in the Command Input (F5)box
1. Enter an MML command in the Command Input (F5)box of the MML command
line.
2. Press Enteror click at the right side of the command input box.
All the parameters of the command are displayed in the command parameter area.
3. Enter the parameter value in the command parameter area.
4. Press F9or click at the right side of the command input box.
The execution results are displayed in the Common Maintenancewindow of the
MML command line.
l Selecting the MML command in the History Commandbox
1. Select a history command in the history command box. You can press F7or F8to
select the previous or the next history command. Alternatively, you can press orbehind the history command box to select the previous or the next history
command.
All the parameters of the command are displayed in the command parameter area.
2. Modify the parameter value in the command parameter area.
3. Press F9or click to run the command.
The execution results are displayed in the Common Maintenancewindow of the
MML command line.
l Copying the MML command scripts to the command input area
1. Copy the complete scripts of the MML command to the command input area.
2. Press F9or click to run the command.
The execution results are displayed in the Common Maintenancewindow of the
MML command line.
l Selecting the MML command in the MML Commandof the navigation tree
1. Double-click the MML command in the MML Commandof the navigation tree.
2. Enter the parameter value in the command parameter area.
3. Press F9or click to run the command.
The execution results are displayed in the Common Maintenancewindow of the
MML command line.
----End
2.8.5 Batching MML Commands
This part describes how to batch the man-machine language (MML) commands. Batching MML
commands refer to that multiple MML commands are executed at one time. You can run the
edited batch files on the local maintenance terminal (LMT), eliminating the need to run an MML
command at one time.
Prerequisite
l The LMT is started and the GGSN9811 is displayed.
2 Using the LMT of the GGSN9811
HUAWEI GGSN9811 Gateway GPRS Support Node
Operation Guide
2-20 Huawei Proprietary and Confidential
Copyright Huawei Technologies Co., Ltd
Issue 03 (2008-04-10)
7/25/2019 01-02 Using the LMT of the GGSN9811
21/24
l If the configuration commands need to be executed, ensure that the right to configure the
commands is granted.
l The MML command line is started.
l The batch files are available.
Context
The batch file (file of data scripts) is a text file made through MML commands. The scripts of
a group of MML commands for completing a specific task are saved in the batch file. The MML
commands are automatically batched according to the order of the scripts in the batch file.
You can batch the MML commands in two ways.
l Immediate batch command: indicates that the specified batch file is run immediately.
l Timing batch command: indicates that the system runs the batch file at a specified time of
a specified date.
Procedure
l Immediate batch command
1. Choose System > Batch Commands...on the LMT or press Ctrl+E. The MML
Batchwindow is displayed. Refer to Figure 2-13.
Figure 2-13Immediate batch command
HUAWEI GGSN9811 Gateway GPRS Support Node
Operation Guide 2 Using the LMT of the GGSN9811
Issue 03 (2008-04-10) Huawei Proprietary and Confidential
Copyright Huawei Technologies Co., Ltd
2-21
7/25/2019 01-02 Using the LMT of the GGSN9811
22/24
2. Click Newin the Immediate Batch Commandtab, and then enter the batch
commands in the input box. Alternatively, click Open...to select an edited batch file.
3. Set running parameters.
4. Click Go.
l Timing batch command
1. Choose System > Batch Commands...or press Ctrl+Eon the LMT. The MML
Batchwindow is displayed. Refer to Figure 2-13.
2. Select the Timing Batch Commandtab. Refer to Figure 2-14.
Figure 2-14Timing batch command
3. Click the icon besideBatch File
to select the batch file.
4. Click the icon beside the Execution Timeto set the execution time.
5. Click Add.... The MML Batchwindow must be displayed. Otherwise, the timing task
is deleted.
----End
2.9 Logging Out of the LMT
This part describes how to log out of the local maintenance terminal (LMT) of the
GGSN9811.
2 Using the LMT of the GGSN9811
HUAWEI GGSN9811 Gateway GPRS Support Node
Operation Guide
2-22 Huawei Proprietary and Confidential
Copyright Huawei Technologies Co., Ltd
Issue 03 (2008-04-10)
7/25/2019 01-02 Using the LMT of the GGSN9811
23/24
Procedure
Step 1 You can log out of the LMT in the following ways.
l Choose System> Log Out.
l Press Alt+X.
l Click .
Step 2 The Confirmationdialog box is displayed. Click OK.
You log out of the LMT.
----End
HUAWEI GGSN9811 Gateway GPRS Support Node
Operation Guide 2 Using the LMT of the GGSN9811
Issue 03 (2008-04-10) Huawei Proprietary and Confidential
Copyright Huawei Technologies Co., Ltd
2-23
7/25/2019 01-02 Using the LMT of the GGSN9811
24/24