8/18/2019 02-Huawei SDCCH Call Drop Optimization
1/26
GSM BSS Network KPI (SDCCH Call Drop Rate) Optimization Manual INTERNAL
2015-4-13 Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
Page 1 of 26
Product Name Confidentiality Level
G3BSC INTERNAL
Product Version Total 26 pages
GSM BSS Network KPI (SDCCH Call Drop Rate)
Optimization Manual(For internal use only)
Prepared by Du Jian, WCDMA & GSM NetworkPerformance Research Dept.
Date 2008-8-25
Reviewed by Date yyyy-mm-dd
Reviewed by Date yyyy-mm-dd
Approved by Date yyyy-mm-dd
Huawei Technologies Co., Ltd.All rights reserved
8/18/2019 02-Huawei SDCCH Call Drop Optimization
2/26
8/18/2019 02-Huawei SDCCH Call Drop Optimization
3/26
GSM BSS Network KPI (SDCCH Call Drop Rate) Optimization Manual INTERNAL
2015-4-13 Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
Page 3 of 26
Contents
1 Overview of SDCCH Call Drop Rate ....... ....... ....... ........ .... ........ ....... ....... ........ .... ....... ....... 6
1.1 Definition ......................................................................................................................................................... 6
1.2 Recommended Formula ................................................................................................................................... 6
1.3 Signaling Procedure and Measurement Points ................................................................................................. 7
2 Factors That Affect SDCCH Call Drop Rate ....... ....... ........ ....... .... ........ ....... ........ ....... .... ... 8
2.1 Hardware Failure .............................................................................................................................................. 8
2.2 Transmission .................................................................................................................................................... 8
2.3 Version Upgrade ............................................................................................................................................... 8
2.4 Parameter Setting ............................................................................................................................................. 8
2.5 Intra-Network and Inter-Network Interference ................................................................................................ 9
2.6 Coverage Problem ............................................................................................................................................ 9
2.7 Antenna System ............. ............. ............ ............. ............. ............ .............. ............ ............. ............. ............ .. 10
2.8 Imbalance Between Uplink and Downlink..................................................................................................... 10
2.9 Repeater.......................................................................................................................................................... 10
3 Analysis of and Solutions to High SDCCH Call Drop Rate ....... ....... ....... ........ .... ........ .. 11
3.1 Analysis Process ............................................................................................................................................. 11
3.2 Solutions to High SDCCH Call Drop Rate .................................................................................................... 13
3.2.1 Checking the Hardware ......................................................................................................................... 14
3.2.2 Checking the Transmission ................................................................................................................... 15
3.2.3 Checking the BSC and BTS Version Upgrade ...................................................................................... 16
3.2.4 Checking the Parameter Settings........................................................................................................... 16
3.2.5 Checking the Interference ..................................................................................................................... 18
3.2.6 Checking the Coverage, Antenna System, and Balance Between Uplink and Downlink ..................... 18
3.2.7 Checking the Repeaters ......................................................................................................................... 19
4 Test Method ........................................................................................................................ 20
5 Remarks About the Signaling Analysis of the SDCCH Call Drop Rate ....... ....... ........ .. 21
6 Cases for SDCCH Call Drop Rate Optimization ....... ....... ........ ....... .... ........ ....... ....... ...... 23
6.1 Case 1: SDCCH Call Drop in a Synchronous Network ................................................................................. 23
6.2 Case 2: Call Drop Due to Imbalance Between Uplink and Downlink ........................................................... 23
6.3 Case 3: Call Drop Due to Antenna System Problem ...................................................................................... 24
6.4 Case 4: Call Drop Due to Transmission Problem ........................................................................................... 25
7 Feedback Form for SDCCH Call Drop Rate ....... ....... ........ ....... .... ........ ....... ........ ....... .... .. 26
8/18/2019 02-Huawei SDCCH Call Drop Optimization
4/26
GSM BSS Network KPI (SDCCH Call Drop Rate) Optimization Manual INTERNAL
2015-4-13 Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
Page 4 of 26
Figures
Figure 1-1 Number of successful SDCCH seizures............................................................................................... 7
Figure 1-2 Number of successful SDCCH seizures in the signaling channel handover ........................................ 7
8/18/2019 02-Huawei SDCCH Call Drop Optimization
5/26
GSM BSS Network KPI (SDCCH Call Drop Rate) Optimization Manual INTERNAL
2015-4-13 Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
Page 5 of 26
Revision Record
Date Revision Version Change Description Author
2008-8-25 V1.0 Draft completed. Du Jian
References
SN
Document Author Date
1 G-Guide to Eliminating Interference - 20050311-A-1.0 Chen Baolin 2005-3-11
2 GSM BSS Network KPI (Network Coverage) Optimization Manual Xie Haibin 2008-6-18
3 GSM BSS Network KPI (SDCCH Call Drop Rate) Baseline Wu Zhen 2007-6-22
4 GSM BSS Network KPI (Uplink and Downlink Balance)
Optimization Manual
Yang Jixiang 2008-3-26
5
Guide to Solving Call Drop Problems Yang Bin 2002-3-7
6
GSM BSS Network KPI (TCH Call Drop Rate) Optimization Manual Su Shi 2008-6-20
GSM BSS Network KPI (SDCCH Call Drop Rate) Optimization
Manual
Keywords: SDCCH call drop rate, KPI
Abstract: This document describes the definition, test method, and optimization method ofthe SDCCH call drop rate.
Acronyms and Abbreviations:
Acronym and Abbreviation Full Spelling
SDCCH Standalone Dedicated Control Channel
MS Mobile Station
BSC Base Station Controller
KPI Key Performance Index
TCH Traffic Channel
8/18/2019 02-Huawei SDCCH Call Drop Optimization
6/26
GSM BSS Network KPI (SDCCH Call Drop Rate) Optimization Manual INTERNAL
2015-4-13 Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
Page 6 of 26
1 Overview of SDCCH Call Drop Rate1.1 Definition
The SDCCH call drop rate indicates the probability of call drops when the MS occupies theSDCCH. The SDCCH call drop rate is one of accessibility KPIs. This KPI reflects the seizure
condition of signaling channels. If the value of this KPI is high, user experience is adverselyaffected.
1.2 Recommended FormulaThe SDCCH call drop rate is obtained on the basis of the traffic measurement results. Therecommended formula is as follows:
Call Drop Rate on SDCCH = (Call Drops on SDCCH/Successful SDCCH Seizures +Successful SDCCH Seizures in the signaling channel handover) x 100%
Compared with the formula of the BSC32, the formula of the BSC6000 adds the measurement
of the number of call drops due to release indication received on the SDCCH in stable state.As few call drops due to release indication occur in the existing network, the measurement
values of the BSC32 and BSC6000 are the same in the formula.
For details, see the GSM BSS Network KPI (SDCCH Call Drop Rate) Baseline.
8/18/2019 02-Huawei SDCCH Call Drop Optimization
7/26
GSM BSS Network KPI (SDCCH Call Drop Rate) Optimization Manual INTERNAL
2015-4-13 Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
Page 7 of 26
1.3 Signaling Procedure and Measurement Points
Figure 1-1 Number of successful SDCCH seizures
Figure 1-2 Number of successful SDCCH seizures in the signaling channel handover
The measurement points illustrated in Figure 2 are described as follows:
A indicates the number of successful SDCCH seizures.
B indicates the number of successful SDCCH seizures in the signaling channel handover
8/18/2019 02-Huawei SDCCH Call Drop Optimization
8/26
GSM BSS Network KPI (SDCCH Call Drop Rate) Optimization Manual INTERNAL
2015-4-13 Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
Page 8 of 26
2 Factors That Affect SDCCH Call DropRate
According to user complaints and network optimization experience, the major factors thataffect the SDCCH call drop rate are as follows:
Hardware failure
Transmission
Version upgrade Parameter setting
Intra-network and inter-network interference
Coverage, antenna system, and imbalance between uplink and downlink
2.1 Hardware FailureWhen a TRX or a combiner is faulty, seizing the TCH becomes difficult, and thus the SDCCHcall drop rate increases.
2.2 TransmissionThe SDCCH call drop rate increases in any of the following conditions: (1) The transmissionquality is poor on the A or Abis interface due to var ious reasons. (2) Transmission links are
unstable.
2.3 Version UpgradeAfter the BTS version or BSC version is upgraded, the BTS version may be incompatible
with the BSC version, and the parameters and algorithms in the new version may be changed.In this case, the SDCCH call drop rate increases.
2.4 Parameter SettingThe settings of some parameters on the BSC and MSC sides may affect the SDCCH call droprate. If the following situations occur, the SDCCH call drop rate may increase:
8/18/2019 02-Huawei SDCCH Call Drop Optimization
9/26
GSM BSS Network KPI (SDCCH Call Drop Rate) Optimization Manual INTERNAL
2015-4-13 Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
Page 9 of 26
Radio link and cell parameters:
SACCH Multi-Frames (SACCH period (480ms)) and Radio Link Timeout(SACCH period (480ms)) are set to too small values.
RACH Min.Access Level(dBm) is set to a too small value.
T200 SDCCH(5ms) and N200 of SDCCH are set to too small values.
MAIO is set improperly.
Handover parameters:
SDCCH HO Allowed is set to Yes.
T3103A(ms) and T3103C(ms) are set to too small values.
T3109(ms) is set to a too small value.
T3111(ms) is set to a too small value.
The length of timer T305/T308 is set to an invalid or too great value.
Disconnect Handover Protect Timer is set to a too small value.
The network planning is improper after the Um interface is synchronized.
Software Parameter 13 and MAX TA are set to too small values.
2.5 Intra-Network and Inter-Network InterferenceIf inter-network interference and repeater interference exist, or if severe intra-network
interference occurs because of tight frequency reuse, call drops may occur on SDCCHs due to poor QoS. This affects the SDCCH call drop rate.
The following types of interference may occur:
1.
Inter-network interference from scramblers or privately installed antennas
2. Interference from the CDMA network
3. Repeater interference
4.
Intermodulation interference from BTSs
5. Intra-network co-channel and adjacent-channel interference
2.6 Coverage ProblemThe following coverage problems may affect the SDCCH call drop rate.
1. Poor indoor coverage
Densely distributed buildings and thick walls cause great attenuation and low indoor signal
level, which causes call drops.
2. Coverage failure
If the signal from an antenna is blocked or the BCCH TRX is faulty, call drops may occur.
8/18/2019 02-Huawei SDCCH Call Drop Optimization
10/26
GSM BSS Network KPI (SDCCH Call Drop Rate) Optimization Manual INTERNAL
2015-4-13 Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
Page 10 of 26
2.7 Antenna SystemThe following antenna system problems may affect the SDCCH call drop rate
1. If the transmit antennas of two cells are misconnected, the uplink signal level in each cell
is much lower than the downlink signal level in the cell. Therefore, call drops are likelyto occur at a place far away from the BTS.
2.
If a directional cell has main and diversity antennas, the BCCH and SDCCH of the cellmay be transmitted from different antennas. If the two antennas have different pitch
angles or azimuths, the coverage areas of the two antennas are different. In this case, thefollowing result may occur: An MS can receive the BCCH signals from one antenna;
when a call is made, the MS cannot seize the SDCCH transmitted by the other antennaand thus a call drop occurs.
3. If the feeder is damaged, if water runs into the feeder, or if the feeder and the connector
are not securely connected, both the transmit power and receiver sensitivity of theantenna are reduced. Thus, call drops probably occur.
2.8 Imbalance Between Uplink and DownlinkThe difference between the uplink signal level and the downlink signal level may be great inthe following conditions: The transmit power of the BTS is high; the tower mounted amplifier
(TMA) or BTS amplifier does not work properly; the antenna and the connector are notsecurely connected. As a result, call drops may occur at the edge of the BTS coverage area.
2.9 RepeaterIf a cell is installed with a repeater, BTS coverage problems may occur in the case that therepeater is faulty or that the uplink and downlink gain is inappropriately set. Therefore, the
call drop rate increases.
If a wide-frequency repeater is used and the gain is set to a great value, strong interference
may be caused. As a result, the network quality is adversely affected and the call drop rateincreases.
8/18/2019 02-Huawei SDCCH Call Drop Optimization
11/26
GSM BSS Network KPI (SDCCH Call Drop Rate) Optimization Manual INTERNAL
2015-4-13 Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
Page 11 of 26
3 Analysis of and Solutions to HighSDCCH Call Drop Rate
3.1 Analysis Process
8/18/2019 02-Huawei SDCCH Call Drop Optimization
12/26
GSM BSS Network KPI (SDCCH Call Drop Rate) Optimization Manual INTERNAL
2015-4-13 Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
Page 12 of 26
开始
传输或硬件是否存在问题
是否由于版本升级
数据配置是否
存在问题
是否存在干扰
覆盖是否存在问题
天馈是否存在问题
是否上下行不平衡
直放战是否存在问题
确定掉话率高小区
结束
解决硬件或传输问题
检查版本BUG 更换版本或打补
丁
调整切换功控等
相关参数
是否是网内干
扰
排查外部干扰
检查频率规划情况
根据覆盖优化指导书优化覆盖
调整天馈
根据指导书优化上下行不平衡问
题
解决直放战问题
掉话率问题是
否解决
否
否
否
否
否
否
否
否
否
否
是
是
是
是
是
是
是
是
是
Comment [x1]:开始:Start
确定掉话率高小区:Determine the cell wit
high call drop rate传输或硬件是否存在问题:Transmissionhardware failure?
解决硬件或传输问题:Rectify the
transmission or hardware fault
是否由于版本升级:The problem is caused
version upgrade?
检查版本 BUG:Check version informatio
更换版本或打补丁:Replace the version oinstall patches
数据配置是否存在问题:The dataconfiguration is improper?
调整切换功控等相关参数:Adjust related parameters such as handover and power
control
是否存在干扰:The interference exists?
是否是网内干扰:Intra-network interferen
检查外部干扰:Check external interferenc
检查频率规划情况:Check frequency planning
覆盖是否存在问题:The coverage proble
occurs?
根据覆盖优化指导书优化覆盖:Optimize
coverage according to the coverage
optimization guide
天馈是否存在问题:The antenna system is
faulty?
调整天馈:Adjust the antenna system
是否上下行不平衡:ImUnbalance betweeuplink and downlink?
根据指导书优化上下行不平衡问题:
Optimize the imbalance between uplink anddownlink
直放站是否存在问题:The repeater is faul解决直放站问题:Rectify the repeater faul
掉话率问题是否解决:Check the call droprate
结束:End
是:Yes
否: No
8/18/2019 02-Huawei SDCCH Call Drop Optimization
13/26
GSM BSS Network KPI (SDCCH Call Drop Rate) Optimization Manual INTERNAL
2015-4-13 Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
Page 13 of 26
3.2 Solutions to High SDCCH Call Drop RateBefore analyzing the causes of high SDCCH call drop rates, you should find out the
difference between the actual SDCCH call drop rate and the expected value. You should alsofind out the influence of the problems and the related KPIs.
You can analyze the distribution of call drops based on the related traffic measurement results.
If a certain type of call drop accounts for a large proportion of call drops, you can locate thefault by performing the corresponding procedure. The following table lists the distribution of
call drops based on the type of call drop and the cause for call drop in the traffic statistics.
Analyzing the traffic statistics based on the cause for call drop
Type of Call Drop
Cause for Call Drop MeasurementCode
InterfaceDistribution
Call Drops due to CONN FAIL Received
on SDCCH in Stable State
Radio Link Failure M3001A The sum of the
counter and the
number of calldrops due to
SDCCHhandover failure
is the number ofcall drops on
radio interface(SDCCH).
HO Access Failure M3001B
OM Intervention M3001C
Radio Resource
Unavailable
M3001D
Other Causes M3001E
Call Drops due to ERR IND Received on
SDCCH in Stable State
T200 Expired M3000A
Unsolicited DM
Response
M3000B
Sequence Error M3000C
Call Drops due to REL IND Received on
SDCCH
Release Indication M3002
Call Drops due to No MRs from MS for aLong Time
M302 As the seizureduration of the
SDCCH is short,the call drop
may not occur.
Call Drops due to Abis Terrestrial LinkFailure
M303 Number of calldrops on the
SDCCH due totransmission and
equipmentcauses
Call Drops Due to Equipment Failure
M304
Call Drops due to Forced Handover M305
Call Drops due to Resource Check M306
Clear Requests Sent on the A Interface
M309
According to the traffic statistics, you can obtain the distribution of SDCCH call drops due to
Um and non Um causes. For Um causes, you need to check configuration parameters andnetwork interference. For hardware causes, you need to check hardware, transmission, and
equipment failure. If no obvious causes are found, you can perform the procedures shown in
8/18/2019 02-Huawei SDCCH Call Drop Optimization
14/26
GSM BSS Network KPI (SDCCH Call Drop Rate) Optimization Manual INTERNAL
2015-4-13 Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
Page 14 of 26
the preceding figure. The following table lists the mapping between the traffic measurementcounters and the troubleshooting procedures.
Traffic Measurement Counter
Troubleshooting Procedure
M3000A (T200 expired) 3.2.4 (check whether the T200 and N200 are set properly)
M3001A (radio link failure) 3.2.4 (check whether the radio link failure counter
and the number of SACCH multi-frames are set properly)
M3001D (radio resource
unavailable)
3.2.1 (check hardware failure)
M303 (Abis terrestrial link failure)
3.2.2 (check the transmission)
M304 (equipment failure)
3.2.1 (check hardware failure)
The following sections describe the solutions to high SDCCH call drop rates.
The traffic measurement counters and parameters in this document are the same as those inthe BSC6000V9R8C01B051 version.
3.2.1 Checking the Hardware
If a TRX or a combiner is faulty or if an RF cable is incorrectly connected, seizing the
SDCCH becomes difficult, and thus the SDCCH call drop rate increases. You can checkwhether hardware is faulty by viewing BTS alarms or viewing the hardware state on the Site
Device Panel tab page of the LMT. The following table lists the major BSC alarms related to
hardware failures.
Alarm ID
Alarm Name
1000 LAPD OML Fault
2204
TRX Communication Alarm
4414
TRX VSWR Alarm
3606
DRU Hardware Alarm
In addition, you can locate the fault by checking the traffic measurement related to hardware
failures.
8/18/2019 02-Huawei SDCCH Call Drop Optimization
15/26
GSM BSS Network KPI (SDCCH Call Drop Rate) Optimization Manual INTERNAL
2015-4-13 Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
Page 15 of 26
Cause BSC-Level Cell-Level
EquipmentFaults
BSC Measurement -> Accessmeasurement per BSC ->
Congestion Ratio on SDCCH perBSC
Call Drop Ratio on SDCCH perBSC
SDCCH Availability per BSC
Channel Measurement ->
Analyzed Measurement of Available
Channels (SDCCH)
Call Drop Measurement per Cell in Call
Measurement:
Call Drops due to Equipment Failure
(Signaling Channel)
3.2.2 Checking the Transmission
Poor transmission quality, unstable transmission links, or insufficient resources on the Abis or
A interface may lead to the increase of the SDCCH call drop rate . You can check the
transmission conditions by viewing the alarms related to transmission. If a large number oftransmission alarms are generated, you can infer that transmission failures occur. Then, youshould check the transmission connections.
The following table lists the BSC alarms related to transmission failures.
Alarm ID Alarm Name
1000 LAPD OML Fault
11270
LAPD Alarm
11278
E1 Local Alarm
11280 E1 Remote Alarm
20081 Loss of E1/T1 Signals (LOS)
20082 Loss of E1/T1 Frames (LOF)
In addition, you can locate the fault by checking the traffic measurement related to
transmission failures.
Cause BSC-Level Cell-Level
Transmission
failure
BSC Measurement -> LAPDMeasurement
Call Measurement: -> Channel ActivationMeasurement per Cell
CHAN ACTIV NACK Messages Sent by BTS
Channel Activation Timeouts
Call Measurement -> :Call Drop Measurement per Cell
Measurement of Call Drops Due to AbisTerrestrial Link Failure
8/18/2019 02-Huawei SDCCH Call Drop Optimization
16/26
GSM BSS Network KPI (SDCCH Call Drop Rate) Optimization Manual INTERNAL
2015-4-13 Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
Page 16 of 26
3.2.3 Checking the BSC and BTS Version Upgrade
If the SDCCH call drop rate increases after the BSC version or BTS version is upgraded, Youshould check whether the BTS version is compatible with the BSC version and whether the
parameters and algorithms in the new version are changed.
To locate the problem, you can check the version description document and the related
documents, or provide the feedback for the R&D department to learn whether the new versionhas known defects. If the new version has defects, you should replace it with another version
or install the patch.
For details, see the BSC6000 Upgrade Guide.
3.2.4 Checking the Parameter Settings
The parameter settings on the BSC side and MSC side may affect the SDCCH call drop rate.You should check the settings of the following parameters for a cell with a high SDCCH call
drop rate.
SACCH Multi-Frames (SACCH period (480 ms))
This parameter determines whether an uplink radio link is faulty. Each time the BTS fails
to decode the measurement report on the SACCH from the MS, the counter decreases by1. Each time the BTS successfully decodes the measurement report on the SACCH, the
counter increases by 2. When the value of this parameter is 0, the BTS regards the radio
link as faulty. In the traffic measurement, if there are many call drops (M3001A) relatedto radio link failure, you can infer that the radio propagation conditions are poor. In this
case, you can set this parameter to a greater value.
Radio Link Timeout (SACCH period(480ms))
This parameter determines whether a downlink radio link is faulty. Each time the BTSfails to decode the measurement report on the SACCH from the MS, the counter
decreases by 1. Each time the BTS successfully decodes the measurement report on the
SACCH, the counter increases by 2. When the value of this parameter is 0, the BTS
regards the radio link as faulty. In the traffic measurement, if there are many call drops(M3001A) related to radio link failure, you can infer that the radio propagationconditions are poor. In this case, you can set this parameter to a greater value.
RXLEV_ACCESS_MIN
This parameter specifies the minimum receive level of an MS to access the BSS. If this
parameter is set to a too small value, some MSs with low receive levels may access the
network and call drops are likely to occur. You can set this parameter to a great value toreduce the SDCCH call drop rate. The counters related to traffic volume, however, are
accordingly affected.
RACH Min.Access Level
This parameter determines whether an MS can access the network over the RACH. Ifthis parameter is set to a too small value, some MSs with low signal levels may access
the network and call drops are likely to occur. You can set this parameter to a great value
to reduce the SDCCH call drop rate. The counters such as call setup success rate and
paging success rate, however, are affected.
Min DL Power on HO Candidate Cell and Min Access Level Offset
The sum of the values of the two parameters specifies the minimum downlink receive
level of a candidate neighboring cell for a handover. If this parameter is set to a too greatvalue, some desired cells may be excluded from the candidate cells; if this parameter is
set to a too small value, an unwanted cell may become the candidate cell. Both
conditions may lead to the increase of call drops.
8/18/2019 02-Huawei SDCCH Call Drop Optimization
17/26
GSM BSS Network KPI (SDCCH Call Drop Rate) Optimization Manual INTERNAL
2015-4-13 Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
Page 17 of 26
T3103A(ms) and T3103C(ms)
Timer T3103 series consists of T3103A, T3103C, and T8. These timers are started to
wait for a handover complete message. If the lengths of the timers are set to small values,
probably no message is received when timer T3103 series expires. In this case, the BSCconsiders that the radio link in the originating cell is faulty. Then, the BSC releases the
channel in the originating cell. Thus, call drops occur. In the traffic measurement, ifmany call drops are related to handovers (CM361: Call Drops on Radio Interface in
Handover State), you can set this parameter to a greater value. If this parameter is set to atoo great value, channel resources are wasted and TCH congestion occurs.
T3109(ms)
This parameter specifies the period for waiting for a Release Indication message after the
BSC sends a Channel Release message to the BTS. If this parameter is set to a too small
value, the link may be released before the Release Indication message is received. As aresult, a call drop occurs. You can set this parameter to a greater value to reduce the
SDCCH call drop rate. It is recommended that timer T3109 be set to 1 – 2 seconds longerthan timer Radio Link Timeout.
T3111(ms)
This parameter specifies the interval between the time that the main signaling link is
disconnected and the time that a channel is deactivated. The purpose is to reserve a
period of time for repeated link disconnections. If this timer is set to a too small value, achannel may be deactivated too early. Thus, the ca ll drop rate increases.
Timers T305 and T308
Timers T305 and T308 are used on the MSC side. Timer T305 specifies the period
during which the MSC monitors the on-hook procedure. Timer T308 specifies the periodduring which the MSC monitors the resource release procedure. You should set the two
parameters when adding BSC data. Note that the modification of the data in the timer
table does not take effect. If timers T305 and T308 are set to invalid or great values, theMSC clears the call a long time after the MS hangs up. After the T3103 and Radio Link
Timeout timers expire, the number of call drops is increased and thus the call drop rateis significantly affected.
T200 SDCCH(5ms) and N200 of SDCCH
If T200 SDCCH(5ms) and N200 of SDCCH are set to too small values, data links are
disconnected too early. Thus, call drops are likely to occur. If call drops occur because of
T200 expiry (M3400A), you can increase the values of T200 and N200 properly.
Neighboring relationship (affecting call drops in SDCCH handover when the signaling
channel handover is enabled)
If the neighboring cells configured in the BA2 table are incomplete, call drops are likely
to occur in the case of no suitable neighboring cell for handover and progressivedeterioration in the voice quality. Neighboring relationships should be configured
completely on the basis of the drive test data and electronic map (for example, Nastar) to
minimize the call drops due to no available neighboring cells.
Disconnect Handover Protect Timer
This parameter is a software parameter of the BSC. After receiving a DISCONNECT
message from an MS, the BSC cannot hand over the MS within the period specified bythis parameter. Therefore, the following case can be avoided: After being handed over tothe target cell, the MS cannot be put on hook because it does not receive a release
acknowledgement message. You are advised to set this parameter properly.
MA and TSC settings in Um synchronization
The settings involve the AISS function. If the TSC is planned improperly for a cell in the
synchronous network, a great error decoding probability occurs in the area covered by
8/18/2019 02-Huawei SDCCH Call Drop Optimization
18/26
GSM BSS Network KPI (SDCCH Call Drop Rate) Optimization Manual INTERNAL
2015-4-13 Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
Page 18 of 26
the cells with the same BCCH or MA. When the multi-frame link is set up or thesignaling is transmitted at layer 2, the error decoding causes ERR_IND reporting by the
BTS. In this case, call drops occur. If the value of "Call Drops due to ERR IND Receivedon SDCCH in Stable State" is great, you need to optimize TOP cells.
MAIO
If FH is used in a cell, and MAIO is set improperly (for example, the FH offsets ofdifferent TRXs in a cell are set to the same value), the frequencies collide during the FH.
In this case, the call drop rate increases.
Software Parameter 13 and MAX TA
When Software Parameter 13 is enabled and MAX TA is set to a too small value, the
channel is released when the TA of a call exceeds the value of MAX TA. In this case,call drops occur. It is recommended that Software Parameter 13 should not be enabled.
3.2.5 Checking the Interference
If inter-network interference and repeater interference exist, or if severe intra-network
interference occurs because of tight frequency reuse, call drops may occur on SDCCHs due to poor QoS. This affects the SDCCH call drop rate.
The information on UL interference can be obtained by checking the interference bands in the
traffic statistics. The higher percentage of band level 3-5 indicates that serious ULinterference exists. In this case, you need to view the distribution of interference bands in the
SDCCH measurement report of the TRX.
The interference elimination can be classified into intra-network interference elimination and
inter-network interference elimination. For details about interference elimination, see the
G-Guide to Eliminating Interference.
Cause
TRX-Level
Interference MR Measurement ->
Interference Band Measurement per TRX
Mean Number of SDCCHs in Interference Band 1
Mean Number of SDCCHs in Interference Band 2Mean Number of SDCCHs in Interference Band 3
Mean Number of SDCCHs in Interference Band 4Mean Number of SDCCHs in Interference Band 5
3.2.6 Checking the Coverage, Antenna System, and BalanceBetween Uplink and Downlink
For a cell with a high SDCCH call drop rate, you can check its coverage by the DT and CQT.
If the cases (such as too low DL receive level, great difference between the UL and DL levels, poor level quality, lost DL measurement reports, and long call access time) occur, it indicates
that the problems with the coverage and imbalance between uplink and downlink occur in thecell.
For the problematic cell, the call setup success rate and handover success rate slightly fall and
the receive quality becomes poor. In addition, you can analyze the cell coverage according tothe DT route and geographical conditions and then check the antenna system. Some problems
with the coverage and imbalance between uplink and downlink are caused by the reasons such
8/18/2019 02-Huawei SDCCH Call Drop Optimization
19/26
GSM BSS Network KPI (SDCCH Call Drop Rate) Optimization Manual INTERNAL
2015-4-13 Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
Page 19 of 26
as the antenna coverage direction, down tilt, damaged feeder, water running into the feeder,and insecurely connected connector.
For solutions for the problems, see the GSM BSS Network KPI (Network Coverage)
Optimization Manual and the GSM BSS Network KPI (Uplink and Downlink Balance)Optimization Manual .
3.2.7 Checking the Repeaters
Check whether Directly Magnifier Site Flag is set to Yes and SDCCH HO Allowed is set to
Yes in the data configuration on the LMT. If the parameters are set to Yes, you can infer thatthe cell is configured with repeaters. If the parameters are set to No, you should check
whether other operators' repeaters are installed near the cell.
If repeaters are installed, you should check whether they are wide-frequency repeaters, andcheck whether the uplink/downlink amplification coefficient is too great. Ensure that the
amplification coefficient is properly set. If a repeater has an impact on the SDCCH call droprate, you should switch off the repeater.
In addition, you should check whether a repeater is faulty and whether the uplink/downlink
gain is set to a too great/small value. If such problems exist, the coverage area of the BTSchanges. Thus, the SDCCH call drop rate increases.
If repeater problems exist in a cell, the TA distribution varies greatly in the trafficmeasurement results. The following table lists the traffic measurement counters related to
repeaters.
Cause
Cell-Level TRX-Level
Repeater
None MR Measurement ->
Number of MRs Based on TA
8/18/2019 02-Huawei SDCCH Call Drop Optimization
20/26
GSM BSS Network KPI (SDCCH Call Drop Rate) Optimization Manual INTERNAL
2015-4-13 Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
Page 20 of 26
4 Test MethodThe SDCCH call drop rate is one of accessibility KPIs, which can be measured through
registration or reporting of the related traffic measurement KPIs. Currently, vendors andmobile operators use different formulas to calculate the SDCCH call drop rate, thus leading to
different values of this counter. In actual measurement, you should register the specific
counters and use an appropriate formula to calculate the value of this counter.
8/18/2019 02-Huawei SDCCH Call Drop Optimization
21/26
GSM BSS Network KPI (SDCCH Call Drop Rate) Optimization Manual INTERNAL
2015-4-13 Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
Page 21 of 26
5 Remarks About the Signaling Analysis ofthe SDCCH Call Drop Rate
Trace the RSL signaling on the Abis interface. Then, generate the signaling tracing file on theLMT or through the Signal Analyze Tool. Obtain ”CONN_FAIL” and “ERROR_IND”
signaling, and then choose Call Trace from the shortcut menu, as shown in the followingfigure.
Then, right-click a piece of signaling of a call and choose Show Chart from the shortcutmenu, as shown in the following figure.
From the following figure, you can view such information as the uplink and downlink receive
level of the serving cell, uplink and downlink signal quality of the serving cell, downlinkreceive level of neighboring cells, TA, MS power, and BTS power. Based on the information,
you can find out the causes for call drops, such as insufficient downlink coverage andinterference.
8/18/2019 02-Huawei SDCCH Call Drop Optimization
22/26
GSM BSS Network KPI (SDCCH Call Drop Rate) Optimization Manual INTERNAL
2015-4-13 Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
Page 22 of 26
8/18/2019 02-Huawei SDCCH Call Drop Optimization
23/26
GSM BSS Network KPI (SDCCH Call Drop Rate) Optimization Manual INTERNAL
2015-4-13 Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
Page 23 of 26
6 Cases for SDCCH Call Drop RateOptimization
6.1 Case 1: SDCCH Call Drop in a Synchronous NetworkDescription: The 1x3 radio FH mode is used in a BTS. After the synchronization, the
SDCCH call drop rate increases. According to the t raffic measurement, the counter "CallDrops due to ERR IND Received on SDCCH in Stable State (Sequence Error)" increases. The
counter item is M3000C.
Cause analysis and handling: According to the call drop signaling, the BTS reports an ErrorIndication message when the MS is authenticated. In this case, an error occurs when the BTS
and MS transmit the information with serial numbers to be acknowledged on the Um interface.According to the analysis of the layer 2 procedure, if the serial number V(r) carried in the I
frame received by the receive end is different from the expected value, an error is reportedafter the specified threshold is exceeded. According to the analysis of a TOP cell, the cell and
another cell (cross coverage) in the synchronous area use the same main BCCH and BCC
settings. In this case, the error decoding probability greatly increases when the signaling istransmitted at layer 2 in a synchronous network. After the TSC is modified for cross coverage
signals, the SDCCH call drop rate reaches a normal value.
Fault point: The TSC is planned improperly in a synchronous network.
6.2 Case 2: Call Drop Due to Imbalance Between Uplinkand Downlink
Description: The following symptoms occur during the DT: After the test MS camps on a cell,
it cannot make calls; the MS can only receive calls; call drops occur frequently at a certaindistance from the antenna.
Cause analysis and handling: When the uplink signal level is much lower than the downlinksignal level, the power may not be balanced. In this case, the authentication or assignment
procedure cannot be completed.
8/18/2019 02-Huawei SDCCH Call Drop Optimization
24/26
GSM BSS Network KPI (SDCCH Call Drop Rate) Optimization Manual INTERNAL
2015-4-13 Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
Page 24 of 26
The tracing result (as shown in the previous figure) shows that the uplink signal level is muchlower than the downlink signal level. Therefore, call drops occur.
6.3 Case 3: Call Drop Due to Antenna System ProblemDescription: A new BTS3012 is deployed at a site and the cell configuration is S2/2/2. After
the BTS3012 is put into operation, the number of TCH call drops in cell 1 and ce ll 2 in busy
hours reaches 20 and the number of SDCCH call drops reaches 1,000. These counters in cell 3are normal.
Cause analysis and handling: According to the analysis of the traffic measurement results ofTRX-level radio link performance in busy hours, the number of abnormal radio links on both
TRX 3 (TRX 2 and TRX 3 are configured for cell 1) and TRX 7 (TRX 6 and TRX 7 areconfigured for cell 2) is great. TRX 3 and TRX 7 are the second TRX in cell 1 and cell 2
respectively; therefore, they are connected to the TXB channel of the DDPU in the
corresponding cell. The jumpers of the two non-main BCCH TRXs may be misconnected.
According to the analysis of the traffic measurement results related to the uplink and
downlink balance performance, the proportions of the TRX 3 in cell 1 and TRX 7 in cell 2 atlevel 1, level 2, and level 3 are large, which indicates that the downlink loss is too great and
the downlink transmit power is too small. Because TRX 2 (main BCCH TRX) in cell 1 andTRX 6 (main BCCH TRX) in cell 2 transmit the signal through the TXA port of the DDPU in
the sector independently. When the call is assigned on the channel in the non BCCH TRX, the
transmit power decreases sharply and incurs the call drop due to the inverse transmission ofTRX 3 and TRX 7. After the wrong connection between TRX 3 and TRX 7 is adjusted, the
number of call drops on the TCH and the SDCCH in two cells is normal.
8/18/2019 02-Huawei SDCCH Call Drop Optimization
25/26
GSM BSS Network KPI (SDCCH Call Drop Rate) Optimization Manual INTERNAL
2015-4-13 Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
Page 25 of 26
6.4 Case 4: Call Drop Due to Transmission ProblemDescription: At a certain site, the MOTO BTS is replaced with Huawei BTS and the cell
configuration is S2/2/2. At the night of the replacement, calls are made normally and drivetests show that all performance counters are normal. The traffic measurement results within a
measurement period of 15 minutes show that MS-originated and MS-terminated calls aremade normally and handovers are performed normally. After a week of operation, the traffic
measurement results show that the value of the counter SDCCH Seizure Request is not
normal: The maximum number of SDCCH seizure requests reaches 9,000, the number ofSuccessful SDCCH Seizure Requests is over 7,000, and the number of Failed SDCCH
Seizures due to Busy SDCCH is over 900. Compared with the similar SDCCH counters, theTCH traffic volume is small and the TCH call drop rate is high.
Cause analysis and handling: According to the check of the hardware on site, making a callis difficult on site. In addition, some subscribers complain that it is difficult to make calls after
the replacement. After obtaining the consent from the customer, the on-site engineer powers
off the BTS and loads the data again. During the initialization of the BTS, a message is
displayed, indicating that the process is disrupted and that the communication expires. Some parameters of the BTS cannot be initialized. The BTS hardware is normal and the cableconnections are proper.
Before the replacement, the transmission is normal. After the replacement, most of thetransmission cables are the original ones. Huawei engineers replace only the transmission
cable between the transmission equipment room and the Huawei BSC and use a new E1connector to fix the DDF transmission cable to the E1 port on top of the BTS cabinet. The
possible cause is that the E1 connector is made improperly. In this case, the transmission bit
error rate is high and the BTS cannot be completely initialized. As a result, when a subscribermakes a call, assigning a TCH is difficult. A detailed check shows that the E1 connector on
top of the BTS cabinet is made improperly. After a proper E1 connector is used, the problemis solved.
8/18/2019 02-Huawei SDCCH Call Drop Optimization
26/26
GSM BSS Network KPI (SDCCH Call Drop Rate) Optimization Manual INTERNAL
2015-4-13 Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd
Page 26 of 26
7 Feedback Form for SDCCH Call DropRate
If the SDCCH call drop rate is high and technical support is required, you need to fill in thefollowing form.
Check Item Remarks Purpose
Software version Software versions of the BSC andBTS
Check whether the software version is faulty.
Data
configuration
*.dat file Check the network optimization parameters and
power configuration.
Alarminformation
Hardware, clock, and transmissionalarms (self-check)
Check whether these alarms are generated in thecell. Clear the alarms if they are generated.
Traffic
measurement
Cause for call drop Measure SDCCH call drops.
Traffic
measurement
Traffic measurement results related
to the voice quality and the balance between uplink and downlink
Check whether interference and imbalance between
uplink and downlink exist.
Signaling RSL signaling tracing data Check the causes for call drops.
DT data *.log (*.cell site) or *.ant file Based on the DT data, determine whether
interference or coverage problems exist.
Others Engineering parameter table and
electronic map
Check the geographical information through the
Nastar software.