8/9/2019 08B21 SED 6002 96EN00 Rear View Camera
1/26
INSTALLATIONINSTRUCTIONS
Honda Access Corp. 08B21-SED-6002-962006
PARKING AID CAMERA ATTACHMENT KIT
ACCORD
JUL. 2006
INDEXParts List
Attachment Kit...................................................................................................................................................... 1 Parking Aid Camera Kit........................................................................................................................................ 2
Tools and Supplies Required ............................................................................................................................ 2
Before You Begin
Customer Information .......................................................................................................................................... 2
Wire Harness Routing Precaution ....................................................................................................................... 3
Installation ............................................................................................................................................................. 3
Removing the Vehicle Parts................................................................................................................................. 3
Installing the Parking Aid Camera...................................................................................................................... 16
Processing the License Light Garnish and Installing the Parking Aid Camera Garnish .................................... 23Checking the Installation .................................................................................................................................. 26
Parts List
Attachment Kit
Parking aid camera bracket Camera sub harness Parking aid camera garnish
Pattern Blind fasteners (2) Coupler 6P
Grommet Wire ties (33) EPT sealers (9)
8/9/2019 08B21 SED 6002 96EN00 Rear View Camera
2/26
08B21-SED-6002-962 / 26
Parking Aid Camera Kit
Tools and Supplies Required
Before You Begin
Customer Information
Write down the customers radio station presets. The radio memory will be erased when the negative cable is discon-
nected.
The radio may have a coded theft protection circuit. If so, be sure you have the anti-theft code before you disconnect
the battery.
Disconnect the negative cable from the battery.
Be extremely careful not to damage the body paint finish and rear bumper.
To prevent damage to the rear bumper, set it on a cardboard or a blanket during the installation.
Washer-screws (2) Packings A (15) Packings B (2)
Packings C (3)
Parking aid camera Manual
Phillips screwdriver Flat-tip screwdriver Spanner (10 mm)
Ratchet wrench Socket (10 mm) Utility knife
Center-punch Pushpin Electric drill (3, 8, 10 mm bits)
File Touch up paint Eye protection
Hole saw (20 mm) Scissors Shop towel Vinyl tape Contact cleaner Felt-tip pen
Fret-saw Tape measure Cardboard or blanket
8/9/2019 08B21 SED 6002 96EN00 Rear View Camera
3/26
3 / 2608B21-SED-6002-96
Wire Harness Routing Precaution
Disconnect the connectors andterminals by holding them. Donot pull the harness to discon-nect the connector
Do not pull the harness withforce. It will damage the har-ness.
Cut off the excess of the wireties.
Connect the connectors andterminals securely until theylock.
Reinstall the connectors to thecorresponding stays wheneverthey are removed. After opera-tion, check that the connectorsare installed on the stays se-curely and not loose or comeout of the stays.
Take care not to pinch the har-ness with the vehicle parts dur-ing assembly.
Secure the harness to the vehi-cle harness securely not to letthem hang down. Reinstall theclamps of the vehicle if they areremoved.
Installation
Removing the Vehicle Parts
1. Raise the rear seat cushion and release the four
retaining tabs and remove the right slide cover.
5628012B
REAR SEATCUSHION
RIGHT SLIDECOVER
RETAININGTAB
RETAININGTAB
8/9/2019 08B21 SED 6002 96EN00 Rear View Camera
4/26
08B21-SED-6002-964 / 26
2. Remove the weatherstrip. Release the clip A
and two clips B, and remove the right rear side
step.
5829080B
RIGHT REARSIDE STEP
WEATHERSTRIP
CLIP A
CLIPS B (2)
3. Pull down the rear seatback forward. Releasethe three clips and four retaining tabs, and re-
move the right rear side cushion.
5829090B
REARSEATBACK
RIGHT REARSIDE CUSHION
RETAININGTAB
RETAININGTAB
CLIPS (3)
8/9/2019 08B21 SED 6002 96EN00 Rear View Camera
5/26
5 / 2608B21-SED-6002-96
4. Open the tailgate. Release the four clips and re-
move the tailgate upper garnish.
5. Release the two clips and two retaining tabs,
and remove the right and left tailgate side gar-
nishes.
5829100B
TAILGATE UPPERGARNISH
LEFT TAILGATESIDE GARNISH
RIGHT TAILGATESIDE GARNISH
CLIP A
CLIP A RETAININGTAB
RETAININGTAB
CLIP B
CLIP B
6. Open the cap and remove the torx screw.
7. Remove the two clips A from the underside of
the tailgate.
8. Loosen the tailgate lining by removing the
twelve clips. Disconnect the vehicle connector
and remove the tailgate lining.
5829110B
TAILGATE
TAILGATELINING
CLIP A
CLIP A
CAP Open.
TORXSCREW
CLIPS (12)
VEHICLE
CONNECTOR
8/9/2019 08B21 SED 6002 96EN00 Rear View Camera
6/26
08B21-SED-6002-966 / 26
9. Remove the two bolts and two nuts from the in-
ner side of the tailgate.
5829120B
TAILGATE
BOLT
NUT
10. Pull the license light garnish toward you andloosen it by removing the sixteen clips. Discon-
nect the vehicle connector and remove the li-
cense light garnish.
5829130B
LICENSE LIGHTGARNISH
CLIPS (16)
VEHICLECONNECTOR
8/9/2019 08B21 SED 6002 96EN00 Rear View Camera
7/26
7 / 2608B21-SED-6002-96
11. Remove the vehicle seal packings from the in-
ner side of the license light garnish you just re-
moved and replace them with fifteen seal
packings A, two seal packings B and three seal
packings C as shown.
5829140B
LICENSELIGHTGARNISH
VEHICLEPACKING(Discard.)
VEHICLEPACKING(Discard.)
PACKINGS A (2)
PACKINGS A (13)
PACKINGSC (3)
PACKINGSB (2)
STUD
BOLT
CLIP
CLIP
BOLTINSTALLATIONPOSITION
VEHICLE
PACKING(Discard.)
VEHICLE PACKING(Discard.)
12. Release the five clips and remove the rear end
upper garnish.
5829150B
REAR END UPPERGARNISH
CLIPS (5)
8/9/2019 08B21 SED 6002 96EN00 Rear View Camera
8/26
08B21-SED-6002-968 / 26
13. Release the two clips A and remove the floor
center lid.
14. Release the two clips B and two bolts and re-
move the floor rear lid.
15. Remove the rear floor box.
5720051B
FLOORCENTER LID
CLIPS A (2)
FLOORREAR LID
BOLT
CLIPS B (2)
REARFLOORBOX
16. Release the two hooks A and remove the rightlid.
17. Release the hook B and clip A, and remove the
right trunk side pocket lid.
18. Remove the clip C, remove the two clips (both
four retaining tabs), and remove the right side
pocket.
When the car is equipped with the premium
sound system, release the five clips B and
remove the speaker lid.
Remove the left lid, the left trunk side pock-
et lid and the left trunk side pocket in thesame way.
5829160B
HOOK A RIGHTLID
CLIP A
HOOK B
RIGHTTRUNKSIDEPOCKETLID
CLIP C
RIGHTTRUNK SIDEPOCKET
RETAININGTABS (4)
SPEAKERLID
CLIP B
CLIP (2)
8/9/2019 08B21 SED 6002 96EN00 Rear View Camera
9/26
9 / 2608B21-SED-6002-96
19. Remove the weatherstrip.
20. Release the eight clips and remove the rear
panel lining.
5829170B
WEATHERSTRIP
CLIPS (8)
REARPANELLINING
21. Remove the three clips from the right rear sidelining.
22. Remove the two bolts and remove the two an-
chors from the right rear side lining.
5720071B
RIGHTREAR SIDELINING
ANCHOR ANCHOR
BOLT
BOLT
CLIP
CLIP
8/9/2019 08B21 SED 6002 96EN00 Rear View Camera
10/26
08B21-SED-6002-9610 / 26
23. Remove the weatherstrip. Release the retaining
tab using a flat-tip screwdriver and push down
the hook forward. Remove one self-tapping
screw.
24. Release the eight clips and pull the right rear
side lining toward you, disconnect the vehicle
connector and remove the right rear side lining.
5829181B
WEATHERSTRIP
RIGHTREAR SIDE
LINING
CLIPS (8)
VEHICLECONNECTORS (2)
HOOK RETAININGTABFLAT-TIP
SCREWDRIVER
a. When the car is equipped with the premium
sound system, pull out the speaker toward you
by removing the five bolts. Disconnect the vehi-
cle connector and remove the speaker.
5720061B
SPEAKER
BOLT Remove
VEHICLECONNECTOR
8/9/2019 08B21 SED 6002 96EN00 Rear View Camera
11/26
11 / 2608B21-SED-6002-96
25. Release the four clips and turn down the right
quarter pillar garnish.
5720081B
RIGHT QUARTERPILLAR GARNISHCLIPS (4)
Turn down.
26. Release the one retaining tab, band of the hingecover and two clips and remove the right hinge
cover from the hinge.
5829190B
RIGHTHINGE
RIGHTHINGECOVER
CLIP
BAND
RETAININGTAB
27. Pull the front and rear door opening seals out of
position. Release the two clips, release the re-
taining tabs by pushing the top of the right cent-
er pillar lower garnish and loosen the right
center pillar lower garnish. Connect the battery cable to the battery ter-
minal and slide the front seat forward before
loosening the right center pillar lower gar-
nish.
After this step, disconnect the negative ca-
ble from the battery.
5829200B
DOOROPENINGSEAL
RIGHT CENTER
PILLAR LOWERGARNISH
DOOR OPENING SEAL
CLIPS (2)
Push to releasethe retaining tab.
Push to releasethe retaining tab.
8/9/2019 08B21 SED 6002 96EN00 Rear View Camera
12/26
08B21-SED-6002-9612 / 26
28. Release the two retaining tabs and five clips
and remove the right side step garnish.
5629081B
RETAININGTAB
RIGHT SIDESTEP GARNISH
CLIPS (5)
29. Turn up the weatherstrip. Release the two re-taining tabs and two clips, and remove the right
cowl side lining.
5629091B
RIGHT COWLSIDE LINING
CLIPS (2)
WEATHERSTRIP
RETAININGTAB
30. Release the three clips and the three pins, then
remove the passenger under cover.
5829290B
PASSENGERUNDER COVER
CLIPS (3)
PIN
PIN
8/9/2019 08B21 SED 6002 96EN00 Rear View Camera
13/26
13 / 2608B21-SED-6002-96
31. Remove the two self-tapping screws from the
glove box. Open the glove box.
32. Release the stopper. Remove the glove box by
pushing the right and left hooks inward.
2D10120S
GLOVEBOX
SELF-TAPPINGSCREW
STOPPER
HOOK
HOOK
(AT Car)33. Move the gearshift lever to the Neutral (N) posi-
tion.
34. Release the two clips A and four clips B, and re-
move the escutcheon panel.
When the car is equipped with the seat
heater, disconnect the two vehicle connec-
tors before removing the escutcheon panel.
5829300B
ESCUTCHEONPANEL
CLIPS A (2)
CLIPS B (4)
GEARSHIFT LEVER Move the gearshiftlever to the Neutral(N) position.
VEHICLECONNECTOR
8/9/2019 08B21 SED 6002 96EN00 Rear View Camera
14/26
08B21-SED-6002-9614 / 26
(MT Car)
35. Release the two tabs and turn the gearshift
knob counterclockwise and remove it.
5720091B
GEARSHIFTKNOB
TABGEARSHIFTBOOT
36. Release the two clips A and four clips B, and re-move the escutcheon panel.
When the car is equipped with the seat
heater, disconnect the two vehicle connec-
tors before removing the escutcheon panel.
5829310B
CLIPS A (2)
CLIPS B (4)
ESCUTCHEONPANEL
VEHICLECONNECTORS (2)
8/9/2019 08B21 SED 6002 96EN00 Rear View Camera
15/26
15 / 2608B21-SED-6002-96
37. Open the ashtray holder and remove the ash-
tray.
38. Remove the two self-tapping screws, release
the two clips and pull the ashtray holder toward
you.
39. Disconnect the vehicle connectors and bulb.
Release the bulb cord from the holder and re-
move the ashtray holder.
5829320B
ASHTRAYHOLDER
ASHTRAY
VEHICLECONNECTOR
SELF-TAPPINGSCREW
CLIP
BULB CORD
BULBCORD
HOLDER
BULB
40. Release the two self-tapping screws and two
clips, and remove the pocket panel.
5829330B
POCKETPANEL
CLIPS (2)
SELF-TAPPINGSCREW
8/9/2019 08B21 SED 6002 96EN00 Rear View Camera
16/26
08B21-SED-6002-9616 / 26
41. Remove the two nuts and two bolts and remove
the two vehicle harness clip from the vehicle
bracket. Pull the vehicle navigation unit toward
you.
42. Disconnect the five vehicle connectors and re-
move the vehicle navigation unit.
5629102B
BOLT
NUT
VEHICLEHARNESSCLIPS (2)
VEHICLEBRACKET
VEHICLECONNECTORS (5)
VEHICLENAVIGATIONUNIT
Installing the Parking Aid Camera43. Cut out the template A.
44. Align the template A that you just cut out with
the hole in the tailgate and with the two points of
the end of the radius, and secure the template
A with pieces of vinyl tape.
5628060B
TEMPLATE A
TAILGATETEMPLATE A
VINYL TAPE
HOLE IN TAILGATE Align with the holein the template A.
8/9/2019 08B21 SED 6002 96EN00 Rear View Camera
17/26
17 / 2608B21-SED-6002-96
45. Mark the template A at the three points with a
punch as shown.
5628070B
TAILGATE
TEMPLATE A
PUNCH
MARKPOSITION
46. Remove the template A. Drill the template at thethree marked points using an electric drill motor.
Drill with the 3 mm bit first (at the three points),
then drill with the 6 mm, and finish drilling with
the 8 mm bits (at the two points) and with the 20
mm hole saw (at one point).
5628080B
TAILGATE
ELECTRICDRILL MOTOR(3 mm 6 mm
8 mm BIT)
HOLE SAW(20 mm)
DRILL BIT
GUMMEDCLOTHTAPE
PUNCHMARK
20 ~ 30 mm
47. Pass the parking aid camera harness through
the center hole in the parking aid camera brack-
et. Install the parking aid camera bracket on the
parking aid camera using four screws.
Turn the seal side of parking aid camera tothe top.
5817130B
PARKING AIDCAMERABRACKET
PARKING AIDCAMERA
SCREW
PARKING AID
CAMERAHARNESS
SEAL
8/9/2019 08B21 SED 6002 96EN00 Rear View Camera
18/26
08B21-SED-6002-9618 / 26
48. Wind the vinyl tape onto the parking aid camera
terminal and pass it through the grommet.
49. Measure the area shown and secure the grom-
met to the parking aid camera harness. Note
the installation direction of the grommet.
5817140B
PARKING AIDCAMERA
GROMMET
PARKING AIDCAMERA
PARKINGAID CAMERATERMINAL
VINYLTAPE
GROMMET
VINYLTAPE
10 mm
50. Install the blind fasteners in the two 8 mm holesin the vehicle panel.
51. Route the parking aid camera harness through
the 20 mm hole in the vehicle panel. Install the
grommet as shown and install the parking aid
camera bracket on the vehicle panel using two
washer-screws.
5817150B
PARKING AIDCAMERA
GROMMET
BLINDFASTENER
BLINDFASTENER
VEHICLEPANEL
GROMMET
WASHER-SCREW
PARKING AIDCAMERAHARNESS
52. Route the parking aid camera harness along
the vehicle harness to the right hinge. Secure
the parking aid camera harness to the vehicle
harness using eight wire ties.
53. Attach the EPT sealer to the edge of the vehiclepanel where the parking aid camera harness
will contact.
Clean the surface where the EPT sealer will
attach using contact cleaner.
5720102B
PARKINGAID CAMERAHARNESS
WIRE TIES (8)
VEHICLE HARNESS
EPT SEALER
8/9/2019 08B21 SED 6002 96EN00 Rear View Camera
19/26
19 / 2608B21-SED-6002-96
54. Route the parking aid camera harness under
the hinge and route it into the passenger com-
partment. Secure the parking aid camera har-
ness to the vehicle harness using a wire tie.
Do not secure the parking aid camera har-
ness to the washer hose using a wire tie.
2909150T
PARKINGAID CAMERAHARNESS
VEHICLEHARNESS
WIRE TIE
HINGE Route theparking aidcameraharnessunder thehinge.
55. Pull out the parking aid camera harness. Usinga felt-tip pen, mark the harness at the point
where it contacts the edge of the vehicle panel.
Pull the parking aid camera harness to the tail-
gate side, again.
56. Wind the EPT sealer onto the parking aid cam-
era harness so that the marked point on the
parking aid camera harness is at the center of
the EPT sealer.
2015010T
PARKINGAID CAMERAHARNESS
PARKINGAID CAMERAHARNESS
FELT-TIPPEN
MARK WITHFELT-TIP PEN
MARK WITHFELT-TIP PEN
EPTSEALER
8/9/2019 08B21 SED 6002 96EN00 Rear View Camera
20/26
08B21-SED-6002-9620 / 26
57. Secure the parking aid camera harness to the
vehicle harness using three wire ties and three
pieces of EPT sealers as shown.
Cut the two EPT sealers beforehand as
shown.
5913300Y
PARKING AIDCAMERA HARNESS
WIRE TIES (3)
VEHICLEHARNESS
EPT SEALERS(1/2: 3)
EPTSEALER Cut.
58. Remove the vinyl tape from the parking aidcamera harness terminal. Plug the parking aid
camera harness terminal into the 6-pin connec-
tor, lock the connector and connect the 6-pin
connector to the camera sub harness.
59. Secure the camera sub harness and parking
aid camera harness to the vehicle harness us-
ing two wire ties and two pieces of EPT sealers.
60. Attach one piece of EPT sealer to the vehicle re-
lay bracket.
Do not secure the parking aid camera har-
ness to the washer hose with a wire tie. Se-cure it to the vehicle harness.
Cut the EPT sealer beforehand as shown.
Clean the surface where the EPT sealer will
attach using contact cleaner.
5720112B
VEHICLEHARNESS
WIRETIES (2)
EPT SEALERS(1/2: 2) Cut.
RELAY
CAMERA SUBHARNESS
6-PIN CONNECTOR
LOCK
6-PIN CONNECTOR
RED
BLACK
BROWN
BLUE
WHITE
YELLOW
PARKING AIDCAMERA
HARNESS
CAMERA SUBHARNESS
View
8/9/2019 08B21 SED 6002 96EN00 Rear View Camera
21/26
21 / 2608B21-SED-6002-96
61. Secure the camera sub harness to the vehicle
harness using three wire ties.
5628181B
CAMERA SUBHARNESS
VEHICLEHARNESS
WIRE TIE
62. While loosening the right center pillar lower gar-nish, secure the camera sub harness to the ve-
hicle harness using four wire ties.
Connect the battery cable to the battery ter-
minal and slide the front seat forward before
loosening the right center pillar lower gar-
nish.
Do not secure the parking aid camera har-
ness to the washer hose with a wire tie. Se-
cure it to the vehicle harness.
After this step, disconnect the negative ca-
ble from the battery.
5628191B
RIGHT CENTER PILLARLOWER GARNISH Loosen.
VEHICLEHARNESS
CAMERA SUBHARNESS
WIRE TIES (4)
63. Turn up the floor mat. Secure the camera sub
harness to the vehicle panel using three EPT
sealers.
Clean the surface where the EPT sealer will
attach using contact cleaner.
5629112B
CAMERA SUB
HARNESS
EPT SEALER
FLOOR MAT Turn up.
8/9/2019 08B21 SED 6002 96EN00 Rear View Camera
22/26
08B21-SED-6002-9622 / 26
64. Secure the camera sub harness to the vehicle
unit harness using one wire tie.
Connect the battery cable to the battery ter-
minal and slide the front seat to the rear-
most position before securing the camera
sub harness to the vehicle unit harness.
After this step, disconnect the negative ca-ble from the battery.
5629121B
VEHICLE UNITHARNESS
CAMERA SUBHARNESS
WIRE TIE
65. Secure the camera sub harness to the vehicle
panel using an EPT sealer.
Connect the battery cable to the battery ter-
minal and slide the front seat to the rear-
most position before securing the camera
sub harness to the vehicle panel.
Clean the surface where the EPT sealer will
attach using contact cleaner.
After this step, disconnect the negative ca-
ble from the battery.
5629131B
CAMERA SUBHARNESS
EPTSEALER
VEHICLEPANEL
66. Route the camera sub harness along the vehi-
cle harness and route it through the glove box
opening. Secure the camera sub harness as
shown using four wire ties.
5629141BCAMERA SUBHARNESSWIRE TIES (4)
VEHICLEHARNESS
8/9/2019 08B21 SED 6002 96EN00 Rear View Camera
23/26
23 / 2608B21-SED-6002-96
67. Route the camera sub harness to the center
panel opening. Secure the camera sub harness
to the vehicle harness using two wire ties. Align
the end of the vehicle 20-pin connector with the
end of the camera sub harness connector.
5629152B
CAMERA SUBHARNESS
VEHICLEHARNESS
WIRE TIECENTERPANELOPENING
Align.
20-PIN CONNECTOR
68. Connect the camera sub harness to the vehiclenavigation unit.
69. Connect the five vehicle connectors to the vehi-
cle navigation unit. Secure the vehicle naviga-
tion unit to the vehicle using two nuts and two
bolts.
See the illustration for the connecting posi-
tion of the camera sub harness connector.
5628241B
CAMERA SUBHARNESS
VEHICLE NAVIGATIONUNIT
VEHICLECONNECTORS (5)
NUT
BOLT
CAMERA SUB HARNESSCONNECTING POSITION
VEHICLENAVIGATIONUNIT
Processing the License Light Garnish
and Installing the Parking Aid Camera
Garnish
70. Cut out the template B.71. Align the template B that you just cut out with
the license light garnish and secure the tem-
plate with vinyl tape.
2909211T
LICENSE LIGHTGARNISH
TEMPLATE B
VINYLTAPETEMPLATE B
8/9/2019 08B21 SED 6002 96EN00 Rear View Camera
24/26
08B21-SED-6002-9624 / 26
72. Mark the template B at the six points shown us-
ing a pushpin.
Check that the license light garnish is
pierced through at the three lower holes.
2909220T
LICENSE LIGHT GARNISH
PUSHPIN
TEMPLATE B
MARK POSITION (LOWER SIDE) Be sure that the license light garnishis pierced through as it will be drilledfrom the back side.
PUSHPIN
73. Remove the template B. Drill the license lightgarnish at the three upper marks using an elec-
tric drill motor. Drill with the 3 mm bit first, then
finish drilling with the 10 mm bit.
After drilling, remove the burrs thoroughly
from the edge of the holes.
2909230T
LICENSE LIGHTGARNISH
ELECTRIC DRILL MOTOR(3 mm BIT 10 mm BIT)
MARK (UPPER SIDE)
74. From the back side of the license light garnish,
drill it at the three lower marks you made in step
72. Drill using an electric drill motor with the 3
mm bit first, then finish drilling with the 10 mm
bit. After drilling, remove the burrs thoroughly
from the edge of the holes.
2909240T
LICENSE LIGHTGARNISH(BACK SIDE)
ELECTRIC DRILL MOTOR(3 mm BIT 10 mm BIT)
MARK (LOWER SIDE)
8/9/2019 08B21 SED 6002 96EN00 Rear View Camera
25/26
25 / 2608B21-SED-6002-96
75. Cut the template B as shown. Align the six circle
marks on the template B with the six 10 mm
holes and mark around the template using a
felt-tip pen.
5829280B
LICENSELIGHTGARNISH
TEMPLATE B FELT-TIP PEN
Markaround thetemplate B.
TEMPLATE B
76. Using a fret saw, cut along the mark you justmade around the template in step 75.
File off the cut surface.
2909260T
LICENSE LIGHTGARNISH
CUTOUTPART
FRETSAW
77. Install the parking aid camera garnish in the cut-
out in the license light garnish using three re-
taining tabs.
5628251B
LICENSE LIGHTGARNISH
PARKING AID CAMERAGARNISH
RETAININGTAB
8/9/2019 08B21 SED 6002 96EN00 Rear View Camera
26/26
78. Bring the license light garnish close to the tail-
gate. Reconnect the vehicle connector and
align the parking aid camera garnish with the
parking aid camera.
79. Reinstall the license light garnish.
Check that the parking aid camera garnish
aligns with the parking aid camera securely.
Install the license light garnish with care notto drop the seal packings A, B and C out of
position.
5628261B
PARKING AIDCAMERA
VEHICLECONNECTOR
PARKING AIDCAMERAGARNISH
LICENSELIGHTGARNISH
Checking the Installation Check and adjust the installation of the parking aid
camera garnish and parking aid camera lens as
follows not to allow a shadow to be reflected in the
monitor picture.
1. Move the parking aid camera garnish with your
fingers and adjust so that the top edge of the
lens body is equal to the right and left sides by
viewing the lens from the front side.
Adjust so that the right and left edges are
equal in width, too.
5628271B
TOP EDGE OFLENS BODY
RIGHTEDGE OFLENS BODY
LEFT EDGEOF LENSBODY
PARKING AIDCAMERAGARNISH