Printouts, if any, are not controlled. Printed on: 23/01/2018
Mondi Štětí a.s.
STANDARD
Part 13.03
CARBON STEEL PIPING
Mondi Štětí a.s. STANDARD 13.03 Page: 1/18
Version: 1 Valid from: 18.1.2018
Printouts, if any, are not controlled. Printed on: 23/01/2018
STANDARD
Part 13.03
CARBON STEEL PIPING
Worked out by: Verified by: Approved by: Name: Name: Name: Position: Position: Position: Signed by: Signed by: Signed by:
Mondi Štětí a.s. STANDARD 13.03 Page: 2/18
Version: 1 Valid from: 18.1.2018
Printouts, if any, are not controlled. Printed on: 23/01/2018
CONTENT 13.03.01 Pipe classes, summary 13.03.02 Pipes for pipe classes 10C….160C 13.03.03 Elbows for pipe classes 10C...160C 13.03.04 Reducers for pipe classes 10C...160C 13.03.05 Tee pieces for pipe classes 10C...160C 13.03.06 Vent connection DN 25
Mondi Štětí a.s. STANDARD 13.03 Page: 3/18
Version: 1 Valid from: 18.1.2018
Printouts, if any, are not controlled. Printed on: 23/01/2018
TABLE OF CONTENTS
Page
1 Pipe classes, summary ........................................................................................................... 4
2 Pipes for pipe classes 10C…160C ..................................................................................... 10
3 Elbows for pipe classes 10C…63C..................................................................................... 11
4 Reducers for pipe classes 10C…160C .............................................................................. 12 5 Tee pieces for pipe classes 10C…160C ............................................................................ 15 6 Vent connection DN 25 ......................................................................................................... 18
Mondi Štětí a.s. STANDARD 13.03.01 Page: 4/18
Version: 1 Valid from: 18.1.2018
Printouts, if any, are not controlled. Printed on: 23/01/2018
1 Pipe classes, summary
Pipe class Page
10C1C DN 10…DN 1200 5 16C1C DN 10…DN 1200 6 25C1B DN 10…DN 700 7 63C2B DN 10…DN 200 8 160C4B DN 10…DN 550 9
Mondi Štětí a.s. STANDARD 13.03.01 Page: 5/18
Version: 1 Valid from: 18.1.2018
Printouts, if any, are not controlled. Printed on: 23/01/2018
1.1 Pipe Class 10C1C
Pressure MPa
1.0 0.6
Temperature °C
20 200
Piping component
Dimensions Material Notes
Designation Standard Certificate EN 10204
Pipe DN 10...300 DN 350…DN 1200
EN 10216-2, 13.03.02 EN 10217-2 +A1or EN 10217-5+A1, 13.03.02
P235GH
P235GH
EN 10216-2
EN 10217-2 or EN 10217-5
3.1
3.1
Seamless Welded
Elbow DN 10...20 DN 25..1200
Bent pipe EN 10253-2, 13.03.03
P235GH P235GH
EN 10216-2 EN 10253-2
3.1 3.1
R = 3...5Do R = 1.5Do
Tee-piece DN 20…1200
EN 10253-2, 13.03.05
P235GH
EN 10253-2
3.1
Branch connection DN 10...300 DN 350...1200
EN 10216-2 EN 10217-2+A1 or EN 10217-5+A1
P235GH P235GH
EN 10216-2 EN 10217-2
3.1 3.1
Reducer DN 20...1200
EN 10253-2, 13.03.04
P235GH
EN 10253-2
3.1
Cap DN 20...1200
EN 10253-2
P235GH
EN 10253-2
3.1
Welding neck flange DN 10...1200
EN 1092-1 PN 10, Type 11-B1
P245GH
EN 10222-2
3.1
Blind flange DN 10...1200
EN 1092-1 PN 10, Type 05
P265GH
EN 10028-2
3.1
Gasket
EN 1514-1, type IBC, PN 10
1)
Bolt Nut
EN ISO 4014 EN ISO 4032
8.8 2) 8 2)
EN ISO 898-1 EN ISO 898-2
2.2 2.2
Electro galvanized Electro galvanized
Washer
EN ISO 7089 Gr. A
S 235JR or equal
EN 10025-2
Electro galvanized
Threaded fittings DN 10...50
EN 10241
P235GH or equal
EN 10273
3.1
Thread according to ISO 7-1 (R thread))
1) Gasket material depends on flow substance. See “13.01.01 “Technical Specifications for Flow Substances, Piping and Valve Type Selection”. 2) Starting material shall comply with EN 10269. Material certificate from base material.
Mondi Štětí a.s. STANDARD 13.03.01 Page: 6/18
Version: 1 Valid from: 18.1.2018
Printouts, if any, are not controlled. Printed on: 23/01/2018
1.2 Pipe class 16C1C
Pressure MPa
1.6 11.5
Temperature °C
20 200
Piping component
Dimensions Material Notes
Designation Standard Certificate EN 10204
Pipe DN 10...300 DN 350…DN 1200
EN 10216-2, 13.03.02 EN 10217-2 +A1or EN 10217-5+A1, 13.03.02
P235GH
P235GH
EN 10216-2
EN 10217-2 or EN 10217-5
3.1
3.1
Seamless Welded
Elbow DN 10...20 DN 25..1200
Bent pipe EN 10253-2, 13.03.03
P235GH P235GH
EN 10216-2 EN 10253-2
3.1 3.1
R = 3...5Do R = 1.5Do
Tee-piece DN 20…1200
EN 10253-2, 13.03.05
P235GH
EN 10253-2
3.1
Branch connection DN 10...300 DN 350...1200
EN 10216-2 EN 10217-2+A1 or EN 10217-5+A1
P235GH P235GH
EN 10216-2 EN 10217-2
3.1 3.1
Reducer DN 20...1200
EN 10253-2, 13.03.04
P235GH
EN 10253-2
3.1
Cap DN 20...1200
EN 10253-2
P235GH
EN 10253-2
3.1
Welding neck flange DN 10...1200
EN 1092-1 PN 16, Type 11-B1
P245GH
EN 10222-2
3.1
Blind flange DN 10...1200
EN 1092-1 PN 16, Type 05
P265GH
EN 10028-2
3.1
Gasket
EN 1514-1, type IBC, PN 16
1)
Bolt Nut
EN ISO 4014 EN ISO 4032
8.8 2) 8 2)
EN ISO 898-1 EN ISO 898-2
2.2 2.2
Electro galvanized Electro galvanized
Washer
EN ISO 7089 Gr. A
S 235JR or equal
EN 10025-2
Electro galvanized
Threaded fittings DN 10...50
EN 10241
P235GH or equal
EN 10273
3.1
Thread according to ISO 7-1 (R thread))
1) Gasket material depends on flow substance. See “13.01.01 “Technical Specifications for Flow Substances, Piping and Valve Type Selection”. 2) Starting material shall comply with EN 10269. Material certificate from base material.
Mondi Štětí a.s. STANDARD 13.03.01 Page: 7/18
Version: 1 Valid from: 18.1.2018
Printouts, if any, are not controlled. Printed on: 23/01/2018
1.3 Pipe class 25C1B
Pressure MPa
2.5 1.7
Temperature °C
20 250
Piping component
Dimensions Material
Notes
Designation Standard Certificate EN 10204-
Pipe DN 10...300 DN 350…DN 700
EN 10216-2, 13.03.02 EN 10217-2 +A1 or EN 10217-5 +A1, 13.03.02
P235GH P235GH
EN 10216-2 EN 10217-2+A1 or EN 10217-5+A1
3.1 3.1
Seamless Welded
Elbow DN 10...20 DN 25...700
Bent pipe EN 10253-2, 13.03.03
P235GH P235GH
EN 10216-2 EN 10253-2
3.1 3.1
R = 3...5Do R = 1.5Do
Tee-piece DN 20…700
EN 10253-2, 13.03.05
P235GH
EN 10253-2
3.1
Branch connection DN 10...300 DN 350...700
EN 10216-2 EN 10217-2+A1 or EN 10217-5+A1
P235GH P235GH
EN 10216-2 EN 10217-2
3.1 3.1
Reducer DN 20...700
EN 10253-2, 13.03.04
P235GH
EN 10253-2
3.1
Cap DN 20...700
EN 10253-2
P235GH
EN 10253-2
3.1
Welding neck flange DN 10... 700
EN 1092-1 PN 25, Type 11-B1
P245GH
EN 10222-2
3.1
Blind flange DN 10... 700
EN 1092-1 PN 25, Type 05
P265GH
EN 10028-2
3.1
Bolt Nut
EN ISO 4014 EN ISO 4032
8.8 2) 8 2)
EN ISO 898-1 EN ISO 898-2
2.2 2.2
Electro galvanized Electro galvanized
Washer
EN ISO 7089 Gr. A
S 235JR or equal
EN 10025-2
Electro galvanized
Threaded fittings DN 10...50 EN 10241
P235GH or equal
EN 10273
Thread according to ISO 7-1 (R
thread))
Gasket
EN 1514-1, type IBC, PN 25
1)
1) Gasket material depends on flow substance. See “13.01.01 “Technical Specifications for Flow Substances, Piping and Valve Type Selection”. 2) Starting material shall comply with EN 10269. Material certificate from base material.
Mondi Štětí a.s. STANDARD 13.03.01 Page: 8/18
Version: 1 Valid from: 18.1.2018
Printouts, if any, are not controlled. Printed on: 23/01/2018
1.4 Pipe class 63C2B
Pressure MPa
6.3 4.0
Temperature °C
20 460
Piping component Dimensions Material
Notes
Designation Standard Certificate EN 10204-
Pipe DN 10...200
EN 10216-2, 13.03.02
16Mo3
EN 10216-2
3.1
Seamless
Elbow DN 10...20 DN 25...200
Bent pipe 13.03.03
16Mo3 16Mo3
EN 10216-2 EN 10253-2
3.1 3.1
R=4D
Tee-piece DN 20…200
EN 10253-2, 13.03.05
16Mo3
EN 10253-2
3.1
Branch connection DN 10...200
EN 10216-2
16Mo3
EN 10216-2
3.1
Reducer DN 20...200
EN 10253-2, 13.03.04
16Mo3
EN 10253-2
3.1
Cap DN 20...200
EN 10253-2
16Mo3
EN 10253-2
3.1
Welding neck flange DN 10...DN 200
EN 1092-1, PN 63 Type 11-B1
16Mo3
EN 10222-2
3.1
Blind flange DN 10…DN 200
EN 1092-1, PN 63 Type 05
16Mo3
EN 10028-2
3.1
Bolt Nut
EN ISO 4014 EN ISO 4032
40CrMoV4-6 40CrMoV4-6
EN 10269 EN 10269
3.1 3.1
Electro galvanized Electro galvanized
Washer
EN ISO 7089 Gr. A
S 235JR or equal
EN 10025-2
Electro galvanized
Gasket EN 1514-2 Type C/I PN 63
1)
1) Gasket material depends on flow substance. See 13.01.01 “Technical Specifications for Flow Substances, Piping and Valve Type Selection” 2) Starting material shall comply with EN 10269. Material certificate from base material.
Mondi Štětí a.s. STANDARD 13.03.01 Page: 9/18
Version: 1 Valid from: 18.1.2018
Printouts, if any, are not controlled. Printed on: 23/01/2018
1.5 Pipe class 160C4B
Pressure MPa
11.0
Temperature °C
513
Piping component Dimensions Material
Notes
Designation Standard Certificate EN 10204-
Pipe DN 10…125 DN 150…600
EN 10216-2, 13.03.02 EN 10216-2, 13.03.02
10CrMo9-10 X10CrMoVNb9-1
EN 10216-2 EN 10216-2
3.1 3.1
Seamless Seamless
Elbow DN 10…125 DN 150…600
EN 10216-2 Bent pipe, R = 4D EN 10216-2 Bent pipe, R = 4D Wall thickness same as that of pipe
10CrMo9-10 X10CrMoVNb9-1
EN 10216-2 EN 10216-2
3.1 3.1
Main dimensions according to manufacturer’s design.
Cap DN 10…125 DN 150…600
EN 10253-2 EN 10253-2 R1=0,8D, r=0.15D Wall thickness same as that of pipe
10CrMo9-10 X10CrMoVNb9-1
EN 10253-2 EN 10253-2
3.1 3.1
Main dimensions according to manufacturer’s design.
Tee-piece DN 10… 125 DN 200…600
Special T-piece, Special T-piece ,
10CrMo9-10 X10CrMoVNb9-1
EN 10253-2 EN 10253-2
3.1 3.1
Main dimensions according to manufacturer’s design.
Reducer DN 10-125 DN 150-600
Wall thickness same as that of bigger pipe 13.03.04
10CrMo9-10 X10CrMoVNb9-1
EN 10253-2 EN 10253-2 EN 10216-2
3.1 3.1 3.1
Main dimensions according to manufacturer’s design.
1) Gasket material depends on flow substance. See 13.01.01 “Technical Specifications for Flow Substances, Piping and Valve Type Selection”
Mondi Štětí a.s. STANDARD 13.03.02 Page: 10/18
Version: 1 Valid from: 18.1.2018
Printouts, if any, are not controlled. Printed on: 23/01/2018
2 Pipes for pipe classes 10C…160C
2.1 Dimensions
DN D x T
10C1C 16C1C 25C1B 63C2B
160C4B
15 21.3 x 2.0 21.3 x 2.9 21.3 x 4.0
20 26.9 x 2.3 According to According to 26.9 x 2.9 26.9 x 4.0
25 33.7 x 2.6 10C1C 10C1C 33.7 x 3.2 33.7 x 4.5
(32) 42.4 x 2.6 42.4 x 3.6 42.4 x 5.6
40 48.3 x 2.6 48.3 x 4.0 48.3 x 6.3
50 60.3 x 2.9 60.3 x 4.5 60.3 x 7.1
(65) 76.1 x 2.9 76.1 x 5.0 76.1 x 8.8
80 88.9 x 3.2 88.9 x 5.0 88.9 x 10
100 114.3 x 3.6 114.3 x 5.6 114.3 x 12.5
(125) 139.7 x 4.0 139.7 x 6.3 139.7 x 14.2
150 168.3 x 4.5 168.3 x 8.8 168.3 x 12.5
200 219.1 x 6.3 219.1 x 11.0 219.1 x 14.2
250 273 x 6.3 273 x 16
300 323.9 x 7.1 323.9 x 20
350 355.6 x 5.6 355.6 x 8.0
400 406.4 x 6.3 406.4 x 8.8
(450) 457 x 6.3 457 x 10.0
500 508 x 6.3 508 x 11.0
550 559 x 28
600 610 x 6.3 610 x 12.5
700 711 x 7.1 711 x 14.2
800 813 x 8.0
900 914 x 10.0
1000 1016 x 10.0 1200 1220 x 12.5
The nominal sizes inside parenthesis shall be avoided.
Mondi Štětí a.s. STANDARD 13.03.03 Page: 11/18
Version: 1 Valid from: 18.1.2018
Printouts, if any, are not controlled. Printed on: 23/01/2018
3 Elbows for pipe classes 10C…63C
3.1 Dimensions
Pressed elbow
Table 1 Dimensions according to pipe classes
3.2 Designation
Name, D x T, R, material, standard No. Example: Elbow, 219.1 x 6.3, 305, P235GH, EN 10253-2
DN D x T R
10C1C 16C1C 25C1B 63C2B
15 21.3 x 2.0 21.3 x 2.9 38
20 26.9 x 2.3 According According 26.9 x 2.9 38
25 33.7 x 2.6 to 10C1C to 10C1C 33.7 x 3.2 38
(32) 42.4 x 2.6 42.4 x 3.6 48
40 48.3 x 2.6 48.3 x 4.0 57
50 60.3 x 2.9 60.3 x 4.5 76
(65) 76.1 x 2.9 76.1 x 5.0 95
80 88.9 x 3.2 88.9 x 5.0 114
100 114.3 x 3.6 114.3 x 5.6 152
(125) 139.7 x 4.0 139.7 x 6.3 190
150 168.3 x 4.5 168.3 x 8.8 229
200 219.1 x 6.3 219.1 x 11.0 305
250 273 x 6.3 381
300 323.9 x 7.1 457
350 355.6 x 5.6 355.6 x 8.0 533
400 406.4 x 6.3 406.4 x 8.8 610
(450) 457 x 6.3 457 x 10.0 686
500 508 x 6.3 508 x 11.0 762
600 610 x 6.3 610 x 12.5 914
700 711 x 7.1 711 x 14.2 1070
800 813 x 8.0 1220
900 914 x 10.0 1370
1000 1016 x 10.0 1525
1200 1220 x 12,5 1830
Mondi Štětí a.s. STANDARD 13.03.04 Page: 12/18
Version: 1 Valid from: 18.1.2018
Printouts, if any, are not controlled. Printed on: 23/01/2018
4 Reducers for pipe classes 10C…160C
4.1 Dimensions See the following table for dimensions.
Concentric reducer, C Eccentric reducer E
Note: The wall thickness of reducer is at least the same as the wall thicknesses of the pipe at the bigger end of the reducer, however at least 2 mm.
Mondi Štětí a.s. STANDARD 13.03.04 Page: 13/18
Version: 1 Valid from: 18.1.2018
Printouts, if any, are not controlled. Printed on: 23/01/2018
4.2 Dimensions for pipe classes 10C...160C
DN1
DN2
D
D1
L Wall Thickness T/T1
10C1C
T/T1 16C1C
T/T1 25C1B
T/T1 63C2B
T/T1 160C4B
T
25 15 20
33.7 21.3 26.9
51 51
2.6/2.0 2.6/2.3
3.2/2.9
3.2/2.9 4.5 4.5
(32) 15 20 25
42.4 21.3 26.9 33.7
51 51 51
2.6/2.0 2.6/2.3 2.6/2.6
3.6/2.9
3.6/2.9
3.6/3.2
5.6 5.6 5.6 5.6
40 15 20 25 32
48.3 21.3 26.9 33.7 42.4
64 64 64 64
2.6/2.0 2.6/2.3 2.6/2.6 2.6/2.6
4.0/2.9 4.0/2.9 4.0/3.2 4.0/3.6
6.3 6.3 6.3 6.3
50 20 25 32 40
60.3 26.9 33.7 42.4 48.3
76 76 76 76
2.9/2.3 2.9/2.6 2.9/2.6 2.9/2.6
4.5/2.9 4.5/3.2 4.5/3.6 4.5/4.0
7.1 7.1 7.1 7.1
(65) 25 32 40 50
76.1 33.7 42.4 48.3 60.3
89 89 89 89
2.9/2.6 2.9/2.6 2.9/2.6 2.9/2.9
According
According
5.0/3.2 5.0/3.6 5.0/4.0 5.0/4.5
8.8 8.8 8.8 8.8
80 32 40 50 (65)
88.9 42.4 48.3 60.3 76.1
89 89 89 89
3.2/2.6 3.2/2.6 3.2/2.9 3.2/2.9
to 10C1C to 10C1C
5.0/3.6 5.0/4.0 5.0/4.5 5.0/5.0
10 10 10 10
100 40 50 (65) 80
114.3 48.3 60.3 76.1 88.9
102 102 102 102
3.6/2.6 3.6/2.9 3.6/2.9 3.6/3.2
5.6/4.0 5.6/4.5 5.6/5.0 5.6/5.0
12.5 12.5 12.5 12.5
(125) 50 (65) 80 100
139.7 60.3 76.1 88.9 114.3
127 127 127 127
4.0/2.9 4.0/2.9 4.0/3.2 4.0/3.6
6.3/4.5 6.3/5.0 6.3/5.0 6.3/5.6
14.2 14.2 14.2 14.2
150 (65) 80 100 (125)
168.3 76.1 88.9 114.3 139.7
140 140 140 140
4.5/2.9 4.5/3.2 4.5/3.6 4.5/4.0
8.8/5.0 8.8/5.0 8.8/5.6 8.8/6.3
12.5 12.5 12.5 12.5
200 80 100 (125) 150)
168.3 88.9 114.3 139.7 168.3
152 152 152 152
6.3/3.2 6.3/3.6 6.3/4.0 6.3/4.5
11/5.0 11/5.6 11/6.3 11/8.8
14.2 14.2 14.2 14.2
250 100 (125) 150 200
273.0 114.3 139.7 168.3 219.1
178 178 178 178
6.3/3.6 6.3/4.0 6.3/4.5 6.3/6.3
300 (125) 150 200 250
323.9 139.7 168.3 219.1 273.0
203 203 203 203
7.1/4.0 7.1/4.5 7.1/6.3 7.1/6.3
Mondi Štětí a.s. STANDARD 13.03.04 Page: 14/18
Version: 1 Valid from: 18.1.2018
Printouts, if any, are not controlled. Printed on: 23/01/2018
DN1
DN2
D
D1
L
Wall Thickness T/T1
10C1C
T/T1 16C1C
T/T1 25C1B
T/T1
350 150 200 250 300
355.6 168.3 219.1 273.0 323.9
330 330 330 330
7.1/4,5 7.1/6.3 7.1/6.3 7.1/7.1
According
8.0/4.5 8.0/6.3 8.0/6.3 8.0/7.1
400 200 250 300 350
406.4 219.1 273.0 323.9 355.6
356 356 356 356
7.1/6.3 7.1/6.3 7.1/7.1 7.1/5.6
to 10C1C
8.8/6.3 8.8/6.3 8.8/7.1 8.8/8.0
(450) 250 300 350 400
457.0 273.0 323.9 355.6 406.4
381 381 381 381
7.1/6.3 7.1/7.1 7.1/5.6 7.1/6.3
10/6.3 10/7.1 10/8.0 10/8.8
500 300 350 400 (450)
508.0 323.9 355.6 406.4 457.0
508 508 508 508
7.1/7.1 7.1/5.6 7.1/6.3 7.1/6.3
11/7.1 11/8.0 11/8.8 11/10
600 350 400 (450) 500
610.0 355.6 406.4 457.0 508.0
508 508 508 508
6.3 6.3 6.3 6.3
12.5 12.5 12.5 12.5
700 400 (450) 500 600
711.0 406.4 457.0 508.0 610.0
610 610 610 610
7.1 7.1 7.1 7.1
14.2 14.2 14.2 14.2
800 (450) 500 600 700
813.0 457.0 508.0 610.0 711.0
610 610 610 610
8.0 8.0 8.0 8.0
900 500 600 700 800
914.0 508.0 610.0 711.0 813.0
610 610 610 610
10 10 10 10
1000 600 700 800 900
1016.0 610.0 711.0 813.0 914.0
610 610 610 610
10 10 10 10
1200 700 800 900 1000
1220.0 711.0 813.0 914.0 1016.0
711 711 711 711
12.5 12.5 12.5 12.5
4.3 Designation Name, type, DN1/ DN2 x T/T1, material, standard No. Example: Reducer, C, 500/ 350 x 7.1/5.6, P235GH, EN 10253-2
Mondi Štětí a.s. STANDARD 13.03.05 Page: 15/18
Version: 1 Valid from: 18.1.2018
Printouts, if any, are not controlled. Printed on: 23/01/2018
5 Tee pieces for pipe classes 10C…160C
5.1 Dimensions
Equal tee Reducing tee Dimensions are according to Table 1.
Mondi Štětí a.s. STANDARD 13.03.05 Page: 16/18
Version: 1 Valid from: 18.1.2018
Printouts, if any, are not controlled. Printed on: 23/01/2018
Table 1
DN1 DN2 D D1 F G 10C1C
T / T1
16C1C
T / T1
25C1B
T / T1
63C2B
T / T1
(32) (32) 42.4 42.4 48 48 2.6 2.6 2.6 2.6 3.6 3.6
(32) 25 42.4 33.7 48 48 2.6 2.6 According 2.6 2.6 3.6 3.2
40 40 48.3 48.3 57 57 2.6 2.6 to 10C1C 2.6 2.6 4.0 4.0
40 (32) 48.3 42.4 57 57 2.6 2.6 2.6 2.6 4.0 4.0
50 50 60.3 60.3 64 64 2.9 2.9 2.9 2.9 5.6 5.6
50 40 60.3 48.3 64 60 2.9 2.6 2.9 2.6 5.6 5.0
(65) (65) 76.1 76.1 76 76 2.9 2.9 3.2 3.2 5.6 5.6
(65) 50 76.1 60.3 76 70 2.9 2.9 3.2 2.9 5.6 4.0
80 80 88.9 88.9 86 86 3.2 3.2 3.6 3.6 6.3 6.3
80 (65) 88.9 76.1 86 83 3.2 2.9 3.6 3.2 6.3 5.8
100 100 114.3 114.3 105 105 3.6 3.6 4.5 4.5 8.8 8.8
100 80 114.3 88.9 105 98 3.6 3.2 4.5 3.6 8.8 8.0
(125) (125) 139.7 139.7 124 124 4.0 4.0 5.0 5.0 10 10
(125) 100 139.7 114.3 124 117 4.0 3.6 5.0 4.5 10 8.8
150 150 168.3 168.3 143 143 4.5 4.5 6.3 6.3 11 11
150 (125) 168.3 139.7 143 137 4.5 4.0 6.3 5.0 11 10
200 200 219.1 219.1 178 178 6.3 6.3 7.1 7.1 12.5 12.5
200 150 219.1 168.3 178 168 6.3 4.5 7.1 5.6 12.5 11
250 250 273.0 273.0 216 216 6.3 6.3 8.8 8.8
250 200 273.0 219.1 216 203 6.3 6.3 8.8 7.1
300 300 323.9 323.9 254 254 7.1 7.1 8.0 8.0 10 10
300 250 323.9 273.0 254 241 7.1 6.3 8.0 6.3 10 8.8
350 350 355.6 355.6 279 279 6.3 6.3 8.8 8.8 11 11
350 300 355.6 323.9 279 270 6.3 7.1 8.8 7.1 11 10
400 400 406.4 406.4 305 305 7.1 7.1 10 10 12.5 12.5
400 350 406.4 355.6 305 305 7.1 6.3 10 8.0 12.5 11
(450) (450) 457.0 457.0 343 343 8.0 8.0 10 10 14.2 14.2
(450) 400 457.0 406.4 343 330 8.0 7.1 10 8.8 14.2 12.5
500 500 508.0 508.0 381 381 8.8 8.8 11 11 16 16
500 (450) 508.0 457.0 381 356 8.8 7.1 11 10.0 16 14.2
600 600 610.0 610.0 432 432 10 10 14.2 14.2 17.5 17.5
600 500 610.0 508.0 432 432 10 8.0 14.2 11.0 17.5 16
Mondi Štětí a.s. STANDARD 13.03.05 Page: 17/18
Version: 1 Valid from: 18.1.2018
Printouts, if any, are not controlled. Printed on: 23/01/2018
Table 1 (continued)
DN1 DN2 D D1 F G 10C1C
T/ T1
16C1C
T / T1
25C1B
T/ T1
700 700 711.0 711.0 521 521 10 10 14.2 14.2 20 20
700 600 711.0 610.0 521 508 10 10 14.2 12.5 20 17.5
800 800 813.0 813.0 597 597 12.5 12.5 16 16
800 700 813.0 711.0 602 572 12.5 10 16 14.2
900 900 914.0 914.0 673 673 12.5 12.5 17.5 17.5
900 800 914.0 813.0 673 648 12.5 11 17.5 16
1000 1000 1016.0 1016.0 749 749 14.2 14.2 20 20
1000 900 1016.0 914.0 749 737 14.2 12.5 20 17.5
1200 1200 1220.0 1220.0 889 838 16 16 22.2 22.2
1200 1000 1220.0 1016 889 813 16 14.2 22.2 20.0
5.2 Designation
Name, DN1/ DN2, T/ T1, material, standard No. Example: Tee piece, 200/ 200, 6.3/ 6.3, P235GH, EN 10253-2
Mondi Štětí a.s. STANDARD 13.03.06 Page: 18/18
Version: 1 Valid from: 18.1.2018
Printouts, if any, are not controlled. Printed on: 23/01/2018
6 Vent connection DN 25
6.1 Dimensions
4 1 Hex head cap DN 25 EN 10241 P235GH or equal
3 1 Valve DN 25, see valve spec.
2 1 Welding nipple, R 1” EN 10241 P235GH or equal
1 1 Pipe 33.7 x 2.6 EN 10216-2 P235GH
Part Pcs Description Standard No. Material
Note: 1) The length of the pipe depends on insulation thickness.
6.2 Designation Name, DN, type, material, standard No. Example: Vent connection, DN 25, A, P235GH, 13.03.06