Download - 2015 Water PriceList 175R5515 Final-combined · 130b2308 mcc101a62kt3e20a 62 59 46.5 21.26 6.69 10.24 280 $2,750 130b2309 mcc101a75kt3e20a 75 71 56 21.26 6.69 10.24 330 $3,200 130b3181

www.danfossdrives.com

Effective May 2015

VLT® AQUA Drive Price list for the Water/Wastewater/Irrigation market

100%full load tested insuring the highest level of quality and reliability

38 1.800.432.6367 Rev. A - May 2015

Danfoss General

Purpose Products

39www.danfossdrives.comRev. A - May 2015

VLT® Micro Drive

M1 M2 M3 M4 M5

Remote mounting kit

LCP 12 with potentiometer

FC 51 MICRO 200 - 240VAC Single Phase

NEMA

Size 230V HP

Input

Current

Output

Current

Chassis/IP20

Frame

Heat Output

Watts

Order

Number ListW H D

1

1/4 3.3 1.2 2.8 5.9 5.8 M1 16 132F0001 $205 1/2 6.1 2.2 2.8 5.9 5.8 M1 25 132F0002 $220

1 11.6 4.2 2.8 5.9 5.8 M1 44 132F0003 $235 2 18.7 6.8 3.0 7.1 6.6 M2 67 132F0005 $290 3 26.4 9.6 3.5 9.4 7.6 M3 85 132F0007 $400

FC 51 MICRO 200 - 240VAC Three Phase

NEMA

Size 230V HP

Input

Current

Output

Current

Chassis/IP20

Frame

Heat Output

Watts

Order

Number ListW H D

1

1/3 2.4 1.5 2.8 5.9 5.8 M1 20 132F0008 $205 1/2 3.5 2.2 2.8 5.9 5.8 M1 25 132F0009 $220

1 6.7 4.2 2.8 5.9 5.8 M1 44 132F0010 $235 2 10.9 6.8 3.0 7.1 6.6 M2 67 132F0012 $290 3 15.4 9.6 3.5 9.4 7.6 M3 85 132F0014 $400 5 24.3 15.2 3.5 9.4 7.6 M3 122 132F0016 $475

FC 51 MICRO 380-480VAC Three Phase

NEMA

Size 460V HP

Input

Current

Output

Current

Chassis/IP20

Frame

Heat Output

Watts

Order

Number ListW H D

1

1/2 1.7 1.1 2.8 5.9 5.8 M1 25 132F0017 $280 1 3 2.1 2.8 5.9 5.8 M1 44 132F0018 $295 2 5.1 3.4 3.0 7.1 6.6 M2 56 132F0020 $400 3 7.3 4.8 3.0 7.1 6.6 M2 81 132F0022 $470 4 9.9 6.3 3.5 9.4 7.6 M3 101 132F0024 $525 5 12.4 8.2 3.5 9.4 7.6 M3 133 132F0026 $555

7.5 16.6 11 3.5 9.4 7.6 M3 167 132F0028 $625 10 21.4 14 3.5 9.4 7.6 M3 218 132F0030 $795

215 29 21 4.9 11.5 9.5 M4 342 132F0058 $1,115 20 31 27 4.9 11.5 9.5 M4 454 132F0059 $1,420 25 36 34 6.5 13.2 M5 428 132F0060 $1,700

3 30 37.5 40 6.5 13.2 M5 520 132F0061 $2,010

Options

Description

Order

Number List

VLT LCP 11 w/o potentiometer 132B0100 $25 VLT LCP 12 with potentiometer 132B0101 $25

VLT LCP Blank Cover 132B0131 $25Remote Mounting Kit for LCP 132B0102 $15

1NEMA 1 kit for M1 frame 132B0103 $10 1NEMA 1 kit for M2 frame 132B0104 $11 1NEMA 1 kit for M3 frame 132B0105 $12 1NEMA 1 kit for M4 frame 132B0120 $22 1NEMA 1 kit for M5 frame 132B0121 $25

De-coupling plate kit for M1 and M2 frames 132B0106 $10 De-coupling plate kit for M3 frame 132B0107 $10

Decoupling kit for M4 and M5 132B0122 $10 2IP21 for M1 frame 132B0108 $20 2IP21 for M2 frame 132B0109 $25 2IP21 for M3 frame 132B0110 $30

DIN rail mounting kit for M1 132B0111 $10

Line Filter MCC 107 Option for FC51

Order

Number List

M1 200-240v 1ø - .25-.50 HP 130B2522 $80 M1 200-240v 1ø - 1 HP 130B2533 $80

M1 200-480v 3ø - .25 - 1 HP 130B2523 $80

M2 200-240v 1ø - 2 HP 130B2525 $135 M2 380-480v 3ø - 2 HP 130B2524 $135

M2 200-240v 3ø- 1.5 - 2 HP & 380-480v 3ø - 3 HP 130B2526 $135

M3 200-240v 1ø - 3 HP 130B2530 $165 M3 200-240v 3ø - 4 HP &

380-480v 3ø - 7.5 HP 130B2528 $165

M3 200-240v 3ø - 3 HP & 380-480v 3ø - 5 HP 130B2531 $165

M3 200-240v 3ø - 5 HP & 380-480v 3ø - 10 HP 130B2527 $165

M3 380-480v 3ø - 4.0 HP 130B2529 $165

FC51 Terminal Cover with RS485 Plug and

Ground Screw

Order

Number List

M1 Frame 132B0126 $5 M2 Frame 132B0127 $5 M3 Frame 132B0128 $5 M4 Frame 132B0129 $5M5 Frame 132B0130 $6

LCP blank cover

MCC Line FIlter

1 NEMA kits have bottom metal plate for conduit entry with bottom cover.

2 IP21 kits have bottom metal plate with rubber gromets for conduit entry with bottom cover and drive top cover.

40 1.800.432.6367 Rev. A - May 2015

Sine-Wave Filters

Order Number Typecode

Output Current Rating Dimensions ( in ) Filter Loss

(w) List Price @50Hz @60Hz @100Hz Height Width Depth

IP0

0 3

x2

40

-50

0 V

AC

130B2404 MCC101A2K5T3E00A 2.5 2.5 2 7.13 2.95 8.07 60 $300 130B2406 MCC101A4K5T3E00A 4.5 4 3.5 7.13 2.95 8.07 65 $340 130B2408 MCC101A8K0T3E00A 8 7.5 5.5 9.69 3.54 8.07 80 $395 130B2409 MCC101A10KT3E00A 10 9.5 7.5 9.69 3.54 8.07 90 $460 130B2411 MCC101A17KT3E00A 17 16 13 9.69 5.12 8.07 115 $510 130B2412 MCC101A24KT3E00A 24 23 18 10.24 5.91 10.24 150 $790 130B2413 MCC101A38KT3E00A 38 36 28.5 14.96 5.91 10.24 160 $1,040 130B2281 MCC101A48KT3E00A 48 45.5 36 18.11 6.69 10.24 260 $1,560 130B2282 MCC101A62KT3E00A 62 59 46.5 21.26 6.69 10.24 280 $1,950 130B2283 MCC101A75KT3E00A 75 71 56 21.26 6.69 10.24 330 $2,350 130B3179 MCC101A115T3E00B 115 109 86 20.47 18.50 13.15 470 $3,200 130B3182 MCC101A180T3E00B 180 170 135 22.83 18.50 12.24 650 $4,650 130B3184 MCC101A260T3E00B 260 246 195 20.47 19.69 15.75 850 $5,600 130B3186 MCC101A410T3E00B 410 390 308 20.47 19.69 19.29 1150 $8,300 130B3188 MCC101A510T3E00B 510 456 360 20.47 19.69 19.29 1450 $9,995 130B3191 MCC101A660T3E00B 660 627 495 24.41 24.41 22.95 2000 $12,900 130B3193 MCC101A800T3E00B 800 712 562 24.41 24.41 22.95 3000 $15,700

[1] MCC 101 Sine Wave Filter Series

[2] Nominal Current. Example - A2K5 - 2.5 amps Nominal AC current

[3] Mains Voltage: T3 - 3 Phase 200-500 VAC / T7 - 3 Phase 525 -690 VAC.

[4] Enclosure: 00 / IP00 : 20 / IP20 : 23 / IP23 :

[5] A&B - Internal Use only

How to Order: Select one item from each of the feature code

blocks to complete a part number.

MCC101 - A2K5 - T3 - E00 - A

[1] [2] [3] [4]

Order Example:

[5]

Perfectmatch for:

FC 102, FC 202, FC 301, FC 302 and FC 322.

VLT® Drive Sine-Wave Filters


Sine-Wave Filters




IP2

0 /

23

3x

24

0-5

00

VA

C

130B2439 MCC101A2K5T3E20A 2.5 2.5 2 7.13 2.95 8.07 60 $360 130B2441 MCC101A4K5T3E20A 4.5 4 3.5 7.13 2.95 8.07 65 $415 130B2443 MCC101A8K0T3E20A 8 7.5 5.5 9.69 3.54 8.07 80 $480 130B2444 MCC101A10KT3E20A 10 9.5 7.5 9.69 3.54 8.07 90 $560 130B2446 MCC101A17KT3E20A 17 16 13 9.69 5.12 8.07 115 $615 130B2447 MCC101A24KT3E20A 24 23 18 10.24 5.91 10.24 150 $950 130B2448 MCC101A38KT3E20A 38 36 28.5 14.96 5.91 10.24 160 $1,330 130B2307 MCC101A48KT3E20A 48 45.5 36 18.11 6.69 10.24 260 $2,350 130B2308 MCC101A62KT3E20A 62 59 46.5 21.26 6.69 10.24 280 $2,750 130B2309 MCC101A75KT3E20A 75 71 56 21.26 6.69 10.24 330 $3,200 130B3181 MCC101A115T3E23B 115 109 86 36.14 35.59 29.76 470 $4,300 130B3183 MCC101A180T3E23B 180 171 135 36.14 35.59 29.76 650 $6,250 130B3185 MCC101A260T3E23B 260 247 195 36.14 35.59 29.76 850 $7,500 130B3187 MCC101A410T3E23B 410 390 308 36.14 35.59 29.76 1150 $10,050 130B3189 MCC101A510T3E23B 510 456 360 45.71 48.19 37.60 1450 $12,200 130B3192 MCC101A660T3E23B 660 627 495 45.71 48.19 37.60 2000 $15,700 130B3194 MCC101A800T3E23B 800 712 562 45.71 48.19 37.60 3000 $18,995




IP0

0 3

x5

25

-69

0 V

AC

130B3195 MCC101A13KT7E00B 13 12 9 18.31 4.53 8.86 115 $1,625 130B4112 MCC101A28KT7E00B 28 26 21 19.88 6.10 10.63 150 $2,995 130B4114 MCC101A45KT7E00B 45 42 33 24.61 6.10 14.57 250 $4,395 130B4116 MCC101A76KT7E00B 76 72 57 20.47 18.50 13.07 475 $6,295 130B4118 MCC101A115T7E00B 115 109 86 20.47 18.50 13.39 750 $7,795 130B4121 MCC101A165T7E00B 165 156 124 18.50 19.69 15.75 1100 $9,595 130B4125 MCC101A260T7E00B 260 246 195 21.06 24.41 18.11 1300 $12,250 130B4129 MCC101A360T7E00B 360 314 270 25.98 31.50 24.02 1800 $15,995 130B4152 MCC101A430T7E00B 430 407 323 25.98 31.50 24.02 2150 $19,250 130B4154 MCC101A530T7E00B 530 502 398 25.98 31.50 26.93 2400 $20,995 130B4156 MCC101A660T7E00B 660 625 496 27.17 31.50 28.07 3000 $22,995




IP

20

/23

3x

52

5-6

90

VA

C

130B3196 MCC101A13KT7E20B 13 12 9 18.31 4.65 9.57 115 $1,950 130B4113 MCC101A28KT7E20B 28 26 21 19.88 6.22 12.20 150 $3,595 130B4115 MCC101A45KT7E20B 45 42 33 24.61 6.22 12.20 250 $5,275 130B4117 MCC101A76KT7E23B 76 72 57 28.15 29.92 24.41 475 $7,500 130B4119 MCC101A115T7E23B 115 109 86 28.15 29.92 24.41 750 $9,250 130B4124 MCC101A165T7E23B 165 156 124 36.14 35.59 31.18 1100 $11,500 130B4126 MCC101A260T7E23B 260 246 195 45.71 48.19 39.02 1300 $14,395 130B4151 MCC101A360T7E23B 360 314 270 45.71 48.19 39.02 1800 $18,995 130B4153 MCC101A430T7E23B 430 407 323 45.71 48.19 39.02 2150 $22,985 130B4155 MCC101A530T7E23B 530 502 398 45.71 48.19 39.02 2400 $24,985 130B4157 MCC101A660T7E23B 660 625 496 45.71 48.19 39.02 3000 $27,885

VLT® Drive Sine-Wave Filters

42 1.800.432.6367 Rev. A - May 2015

Accessories Order Number List Price

130B3137 l-Shape Terminal Kit 1 - 2 holes 10.5mm $75 130B3138 l - Shape Terminal Kit 2 - 4 holes 13 mm $165 130B4178 Cable Glands Floor Mounted IP23 Filters $100 130B4175 Terminal Kit for 40 Amp for dV/dt Filter $25 130B4176 Terminal Kit for 80/105 Amp for dV/dt Filter $40 130B4177 Terminal Kit 160 Amp for dV/dt Filter $45

Protective earth (PE) grounding Plate for IP00 and IP20 wall mounted filters. The accessory bag also includes all necessary screws and cable holders.

Accessories L- Shaped

Voltage Current Enclosure

Order

Number L-shape List Price

380 - 500V

115 00 130B3179 N/A

- 23 130B3181 N/A

180 00 130B3182 N/A 23 130B3183 N/A

260 00 130B3184 130B3137 $110 23 130B3185

410 00 130B3186

130B3138 $245 23 130B3187

510 00 130B3188 23 130B3189

660 00 130B3191

130B3139

$490

23 130B3192

800 00 130B3193 23 130B3194

525 - 690V

13 00 130B3195

N/A

20 130B3196

28 00 130B4112 20 130B4113

45 00 130B4114 20 130B4115

76 00 130B4116 23 130B4117

115 00 130B4118 23 130B4119

165 00 130B4121

130B3137 $110 23 130B4124

260 00 130B4125 23 130B4126

360 00 130B4129

130B3138 $245

23 130B4151

430 00 130B4152 23 130B4153

530 00 130B4154 23 130B4155

660 00 130B4156 130B3139 $490 23 130B4157

Cable Glands for Floor Standing Filters

Nom. filter current rating

(200-380/460/600/690V) [A]

Filter Code

Number

Spare

part no. List Price

315/303/242/192 130B2848

130B4178 $160480/443/344/290 130B2848658/590/500/450 130B2848880/780/630/630 130B2848

Nom. filter current rating

(200-380/460/600/690V) [A]

Filter Code

Number

Accessory

Bag List Price

44/40/32/27 130B2835 130B4175 $40 130B2836

90/80/58/54 130B2838 130B4176 $60 130B2839

106/105/94/86 130B2841 130B4176 $60 130B2842

177/160/131/108 130B2844 130B4127 $135 130B2845

Voltage Current IP Order Number L-shape List Price

380 - 500V

115 00 130B3179

130B4178 $160

23 130B3181

180 00 130B3182 23 130B3183

260 00 130B3184 23 130B3185

410 00 130B3186 23 130B3187

510 00 130B3188 23 130B3189

660 00 130B3191 23 130B3192

800 00 130B3193 23 130B3194

525 - 690V

13 00 130B3195

130B4175 $40

20 130B3196

28 00 130B4112 20 130B4113

45 00 130B4114 20 130B4115

76 00 130B4116

130B4178 $160

23 130B4117

115 00 130B4118 23 130B4119

165 00 130B4121 23 130B4124

260 00 130B4125 23 130B4126

360 00 130B4129 23 130B4151

430 00 130B4152 23 130B4153

530 00 130B4154 23 130B4155

660 00 130B4156 23 130B4157

VLT® Drive Sine-Wave and dV/dt Accessories

Wall Mounted Sine-Wave and dV/dt Filter Accessory Kits for Installation

Order

Number

IP00

Filter

Type

Order

Number

IP20

Filter

Type

Units to the

right use

Accessory Bag

*List

Price

130B2404 SW 130B2439 SW

130B0385 $40 130B2406 SW 130B2441 SW 130B2408 SW 130B2443 SW 130B2409 SW 130B2444 SW 130B2411 SW 130B2446 SW 130B2412 SW 130B2447 SW

130B0386 $45 130B2413 SW 130B2448 SW 130B2341 dV/dt 130B2321 SW 130B2281 SW 130B2307 SW

130B0387 $85 130B2282 SW 130B2308 SW 130B2283 SW 130B2309 SW 130B2835 dV/dt 130B2836 SW 130B4175 $60 130B2838 dV/dt 130B2839 SW 130B4176 $60 130B2841 dV/dt 130B2842 SW 130B4127 $60

*Note: List Prices on this page are for Accessory Kits only and do not include filter units. Ex: Filter 130B2404 or 130B2439 use accessory kit 130B0385 - List $40.


Range: 0.75kW-1.2MW (1- 1600 HP)

Mains voltage:

T2 (up to 45kW / 60 HP)

T4-7 (up to 1.2MW / 1600 HP)

Enclosure: IP00 and IP20/23

Max. Temp. 45C

Voltage drop: – 0.5%

dV/dt Filters


Current rating (Amp)

Filter Losses

(W)

Dimensions (in)

List Price

380V @ 60Hz200-400/440V

@ 50Hz”

460/480V @ 60Hz500/525V @

50Hz”575/600V @

60Hz 690V @ 50Hz H W D

IP0

0

130B2835 MCC102A40KTME00B 44 40 32 27 37 11.61 4.52 6.69 $550 130B2838 MCC102A80KTME00B 90 80 58 54 130 15.15 6.1 8.66 $975 130B2841 MCC102A105TME00B 106 105 94 86 145 15.55 6.1 8.66 $1,375 130B2844 MCC102A160TME00B 177 160 131 108 205 17.51 7.28 9.25 $1,800 130B2847 MCC102A303TME00B 315 303 242 192 315 9.25 11.81 7.48 $2,125 130B2849 MCC102A460TME00B 480 443 344 290 398 9.25 11.81 9.84 $2,750 130B2851 MCC102A645TME00B 658 590 500 450 550 10.62 13.77 9.84 $3,375 130B2853 MCC102A800TME00B 880 780 660 630 850 11.14 15.74 11.41 $5,275



Filter Losses

(W)

Dimensions (in)

List Price

“380V @ 60Hz200-400/440V

@ 50Hz”

“460/480V @ 60Hz

500/525V @ 50Hz”575/600V @

60Hz 690V @ 50Hz H W D

IP2

0/2

3

130B2836 MCC102A40KTME20B 44 40 32 27 37 14.56 4.64 9.52 $655 130B2839 MCC102A80KTME20B 90 80 58 54 130 18.7 6.18 8.66 $1,175 130B2842 MCC102A105TME20B 106 105 94 86 145 18.7 6.22 8.66 $1,525 130B2845 MCC102A160TME20B 177 160 131 108 205 20.66 7.4 9.25 $2,325 130B2848 MCC102A303TME23B 315 303 242 192 315 16.73 27.55 7.48 $2,975 130B2850 MCC102A460TME23B 480 443 344 290 398 16.73 27.55 9.84 $3,475 130B2852 MCC102A645TME23B 658 590 500 450 550 16.73 27.55 9.84 $4,225 130B2854 MCC102A800TME23B 880 780 660 630 850 31.18 37 11.41 $8,450



Filter Losses

(W)

Dimensions (in)

List Price

“380V @ 60Hz200-400/440V

@ 50Hz”

“460/480V @ 60Hz

500/525V @ 50Hz”575/600V @

60Hz 690V @ 50Hz H W D

IP5

4

130B2837 MCC102A40KTME54B 44 40 32 27 37 7.87 12.59 9.84 $1,175 130B2840 MCC102A80KTME54B 90 80 58 54 130 9.05 16.53 13.97 $1,675 130B2843 MCC102A105TME54B 106 105 94 86 145 10.82 18.50 18.11 $2,100 130B2846 MCC102A160TME54B 177 160 131 108 205 10.82 18.50 18.11 $2,975

dV/dt filters reduce the dV/dt values on the motor terminal phase-to-phase voltage – an issue that is important for short motor cables.

The perfect solution for:

• Applications with short motor cables (up to 150 m)

• Applications with older motors

• Aggressive environments

• Applications with frequent braking

[1] MCC102 - dV/dt filter series

[2] Nominal Current. Example - A2K5 - 2.5 amps Nominal AC current

[3] Mains Voltage: T3 - 3 Phase 200-500 VAC / T7 - 3 Phase 525 -690 VAC.

[4] Enclosure: E00 / IP00 : E20 / IP20 : E23 / IP23 : E54 / IP54

[5] B - Internal use only

How to Order: Select one item from each of the feature

code blocks to complete a part number.

MCC102 - A2K5 - T3 - E00 - A

[1] [2] [3] [4]

Order Example:

[5]

Perfectmatch for:

FC 102, FC 202, FC 301, FC 302 and FC 322.

VLT® Drive dV/dt Filters

44 1.800.432.6367 Rev. A - May 2015

IP21 / NEMA 1 Kits for IP20 Wall Mounted Filters

Nom. Filter Current Rating

(200-380 / 460 / 600 / 690 V)Filter Code Number IP21/NEMA 1 List Price

[A]

44/40/32/27 130B2836 130B4179 $85.00 90/80/58/54 130B2839 130B4181 $125.00

106/105/94/86 130B2842 130B4181 $125.00 177/160/131/108 130B2845 130B4182 $140.00

Cable Glands for Floor Standing Filters


(200-380 / 460 / 600 / 690 V)Filter Code Number Cable Glands List Price

[A]

44/40/32/27 130B2835 130B4175 $45.00 130B2836

90/80/58/54 130B2838 130B4176 $60.00 130B2839

106/105/94/86 130B2841 130B4176 $60.00 130B2842

177/160/131/108 130B2844 130B4177 $85.00 130B2845


(200-380 / 460 / 600 / 690 V)Filter Code Number Cable Glands List Price

[A]

315/303/242/192 130B2848

130B4178 $155.00480/443/344/290 130B2850658/590/500/450 130B2852880/780/630/630 130B2854

Options

VLT® Drive dV/dt Filters


Common Mode Filters

VLT Frame

Size

Core dimension [in] Weight

(lbs)

Packaging

Dimensions (in)

Order

Number List PriceW w H h d

A and B 2.36 1.69 1.57 0.98 0.87 .6 5.12 x 3.94 x 2.76 130B3257 $110 C 4.02 2.72 2.40 1.10 1.46 3.5 7.48 x 3.94 x 2.76 130B3258 $460 D 7.44 5.63 4.96 3.15 1.46 5.4 9.25 x 7.48 x 5.51 130B3259 $1,125

E and F 12.01 9.80 5.79 3.74 1.46 10 11.42 x 10.24 x 4.33 130B3260 $1,825

Cable Length

ft (m)

A-and B Frame C frame D frame E-F frame

480V 690V 480V 690V 480V 690V 480V 690V

165ft (50) 2 4 2 2 2 4 2 2330ft (100) 4 4 2 4 4 4 2 4495ft (150) 4 6 4 4 4 4 4 4985 ft (300) 4 6 4 4 4 6 4 4

Common Mode Filters come 2 to a package.

VLT® Drive Common Mode Filters

High-frequency common-mode core kit Reduce electromagnetic interference and eliminate bearing damage by electrical discharge.

High-frequency common-mode (HF-CM) cores are special nano-crystalline magnetic cores which have superior filtering performance compared to regular ferrite cores. They act like a common-mode inductor (between phases and ground).Installed around the three motor phases (U, V, W), they reduce high frequency common-mode currents. As a result, high-frequency electromagnetic interference from the motor cable is reduced. However, the core kit should not be used as the sole mitigation measure, and even when the cores are used, the EMC installation rules shall be followed.

46 1.800.432.6367 Rev. A - May 2015

440V - 480VAC, 60 Hz

Fil

ter

cu

rre

nt

rati

ng

Mo

tor VLT Power

and Current

Ratings

Losses

Aco

ust

ic n

ois

e

Frame size List Price

En

clo

sure

AHF 5 AHF 10 AHF 5 AHF 10

AHF

005

AHF

010

A HP kW A W W dBaAHF

005

AHF

010

AHF

005

AHF

010

IP00 130B1787 130B1770 AHF-DB-010-460-60-00-A AHF-DA-010-460-60-00-A10 5 PK37-

P4K0 7.4 131 93 <70 X1 X1 $1,478 $1,271

IP20 130B1752 130B1482 AHF-DB-010-460-60-20-A AHF-DA-010-460-60-20-A $1,673 $1,495 IP00 130B1788 130B1771 AHF-DB-014-460-60-00-A AHF-DA-014-460-60-00-A

14 10 P5K5-P7K5 13 184 118 <70 X1 X1

$1,731 $1,312 IP20 130B1753 130B1483 AHF-DB-014-460-60-20-A AHF-DA-014-460-60-20-A $1,933 $1,514 IP00 130B1789 130B1772 AHF-DB-019-460-60-00-A AHF-DA-019-460-60-00-A

19 15 P11K 19 258 206 <70 X2 X2 $1,939 $1,409


25 20 P15K 25 298 224 <70 X2 X2 $2,197 $1,622


31 25 P18K 31 335 233 < 72 X3 X3 $2,378 $1,855


36 30 P22K 36 396 242 < 72 X3 X3 $2,524 $1,924


48 40 P30K 47 482 274 < 72 X3 X3 $3,007 $2,377


60 50 P37K 59 574 352 < 72 X4 X4 $3,389 $2,813


73 60 P45K 73 688 374 < 72 X4 X4 $3,805 $3,033


95 75 P55K 95 747 428 < 75 X5 X5 $4,637 $3,474


118 100 P75K 118 841 488 < 75 X5 X5 $5,257 $4,008


154 125 P90K 154 962 692 < 75 X6 X6 $6,219 $4,605


183 150 P110 183 1080 743 < 75 X6 X6 $6,793 $5,121


231 200 P132 231 1194 864 < 75 X7 X7 $7,974 $5,918


291 250 P160 291 1288 905 < 75 X8 X7 $9,638 $7,116


355 300 P200 348 1406 952 < 75 X8 X7 $11,306 $8,901


380 For paralleling of 650 Hp drive 1510 1175 < 77 X8 X7

$12,269 $10,031 IP20 130B3167 130B3165 AHF-DB-380-460-60-20-A AHF-DA-380-460-60-20-A $13,454 $10,816 IP00 130B2259 130B1786 AHF-DB-436-460-60-00-A AHF-DA-436-460-60-00-A

436 350 P250 436 1852 1542 < 77 X8 X8 $13,936 $11,533

IP20 130B1769 130B1751 AHF-DB-436-460-60-20-A AHF-DA-436-460-60-20-A $14,987 $12,088

NEMA 1 Kit Option

Enclosure

Order

Number

NEMA 1 Enclosure AHF Dimensions List

Pricea b c d e

X1 130B3274 4.72 6.30 12.97 13.56 8.48 $475 X2 130B3275 7.48 7.09 17.07 17.66 10.14 $495 X3 130B3276 5.71 8.27 21.40 21.99 9.92 $650 X4 130B3277 9.06 9.06 22.58 21.99 13.50 $795 X5 130B3278 9.06 9.84 26.83 27.42 13.50 $895 X6 130B3279 11.81 10.63 26.83 27.42 16.14 $1,150 X7 130B3281 11.81 12.60 31.36 31.95 18.05 $1,475 X8 130B3282 15.75 13.78 31.36 31.95 21.77 $1,975

Chassis Dimensions

Enclosure

Dimensions

H W D

X1 13.07 7.48 8.11X2 17.72 9.13 9.76X3 23.39 14.88 9.53X4 24.57 14.88 13.11X5 29.09 16.46 13.11X6 30.63 16.46 23.46X7 35.79 18.43 17.68X8 35.87 18.43 21.38

Backplate Option

Enclosure

Order

Number List Price

X1 130B3283 $70 X2 130B3284 $85 X3 130B3285 $115 X4 130B3286 $155 X5 130B3287 $199 X6 130B3287 $199 X7 130B3288 $375 X8 130B3288 $375

Note: All dimensional information is in Inches.

[4] 460-60 Nominal voltage & frequency[5] 00 Open Chassis/IP00

20 Protected Chassis/IP20[6] A Internal use only

How to Order: Select one item from each of the feature code blocks to complete a part number.

[1] [2] [3] [4]

Order Example:

[5]

AHF - DA - 010 - 380-60 - 20 - A

[6]

[1] Advanced Harmonic Filter [2] DA 10% Filter Series

DB 5% Filter Series[3] 010 Current Rating in Amps

VLT® Drive AHF Advanced Harmonic Filters

Harmonic Reduction Products


NEMA 1 Kit Option

Enclosure

Order

Number

NEMA 1 Enclosure AHF Dimensions List

Pricea b c d e

X3 130B3276 5.71 8.27 21.40 21.99 9.92 $650 X4 130B3277 9.06 9.06 22.58 21.99 13.50 $795 X5 130B3278 9.06 9.84 26.83 27.42 13.50 $895 X6 130B3279 11.81 10.63 26.83 27.42 16.14 $1,150 X7 130B3281 11.81 12.60 31.36 31.95 18.05 $1,475 X8 130B3282 15.75 13.78 31.36 31.95 21.77 $1,975

Chassis Dimensions

Enclosure

Dimensions

H W D

X3 23.39 14.88 9.53X4 24.57 14.88 13.11X5 29.09 16.46 13.11X6 30.63 16.46 23.46X7 35.79 18.43 17.68X8 35.87 18.43 21.38

Backplate Option

Enclosure

Order

Number List Price

X3 130B3285 $115 X4 130B3286 $155 X5 130B3287 $199 X6 130B3287 $199 X7 130B3288 $375 X8 130B3288 $375

Note: All dimensional information is in Inches.

500 - 600 VAC, 60 Hz

Fil

ter

cu

rre

nt

rati

ng

Mo

tor VLT Power

and Current

Ratings

Losses

Aco

ust

ic n

ois

e

Frame size List Price

En

clo

sure

AHF 5 AHF 10 AHF 5 AHF 10

AHF

005

AHF

010

A HP kW A W W dBaAHF

005

AHF

010

AHF

005

AHF

010

IP00 130B5261130B5229AHF-DB-015-600-60-00-A AHF-DA-015-600-60-00-A15 10 P11K 15 298 224 <70 x3 x3

$3,746 $2,771 IP20 130B5246130B5212AHF-DB-015-600-60-20-A AHF-DA-015-600-60-20-A $3,971 $3,071 IP00 130B5262130B5230AHF-DB-020-600-60-00-A AHF-DA-020-600-60-00-A

20 16.4 P15K 19 335 233 <70 x3 x3 $4,271 $3,071

IP20 130B5247130B5213AHF-DB-020-600-60-20-A AHF-DA-020-600-60-20-A $4,571 $3,296 IP00 130B5263130B5231AHF-DB-024-600-60-00-A AHF-DA-024-600-60-00-A

24 20 P18K 24 396 242 <70 x3 x3 $4,646 $3,521


29 24 P22K 29 482 274 <70 x4 x4 $5,321 $3,971


36 33 P30K 36 574 352 <70 x4 x4 $6,371 $4,796


50 40 P37K 49 688 374 <70 x5 x5 $7,046 $5,246


58 50 P45K 58 747 428 <70 x5 x5 $8,096 $5,846


77 60 P55K 74 841 488 <72 x6 x6 $8,696 $6,521


87 75 P75K 85 962 692 <72 x6 x6 $9,746 $7,196


109 100 P90K 106 1080 743 <72 x6 x6 $10,646 $8,021


128 125 P110 124 1194 864 <72 x6 x6 $10,946 $8,471


155 150 P132 151 1288 905 <72 x7 x7 $12,746 $10,271


197 200 P160 189 1406 952 <72 x7 x7 $14,696 $11,771


240 250 P200 234 1510 1175 <75 x8 x8 $15,446 $12,596


296 300 P250 286 1852 1288 <75 x8 x8 $18,221 $14,921

IP20 130B5260130B5226AHF-DB-296-600-60-20-A AHF-DA-296-600-60-20-A $18,746 $14,996 IP00 n/a 130B5244 n/a AHF-DA-366-600-60-00-A

366 350 P315/P355 366 2812 1542 <75 x8

n/a $16,046 IP20 n/a 130B5227 n/a AHF-DA-366-600-60-20-A n/a $16,496 IP00 n/a 130B5245 n/a AHF-DA-395-600-60-00-A

395 400 P400 395 2812 1852 <75 x8 n/a $17,021

IP20 n/a 130B5228 n/a AHF-DA-395-600-60-20-A n/a $17,546

VLT® Drive AHF Advanced Harmonic Filters


48 1.800.432.6367 Rev. A - May 2015

VLT® Active Filter 006

Danfoss AAF 006 Advanced Active Filters are designed utilizing 85% of a standard VFD hardware thus offering robust and known Quality performance.

An active filter is not sized by the VFD current, but by the amount of corrective current the filter must induce into the system for correction.

Sizing of the Advanced Active Filter is easily calculated knowing the input current of the VFD.

For example, a 75 Hp VFD draws 95A, and the estimated Harmonic Current is about 40% of that or 38A.

For exact system calculations and AAF sizing, use MCT 10 Harmonic Analyzer available at http://www.danfoss.com/BusinessAreas/DrivesSolutions/Software+MCT10/MCT10+Downloads.htm.

CT’s

For the AAF to operate, Current Transformers (CT’s) need to be added to the system to monitor the Harmonic and Power Factor loads in the system

Ring Style

List price per

set of 3

500:5 $ Consult factory1000:5 $ Consult factory1500:5 $ Consult factory

Split Ring Style

500:5 $ Consult factory1000:5 $ Consult factory1500:5 $ Consult factory

List price

(380 - 480 V) T4

Advanced

Active Filter

[2] Amp Rating*Base NEMA

1 IP21

ADDITIONAL PRICES

[4] Enclosure Adders [5] RFI Hardware [9] Hardware Options C0

NEMA 12

IP54

NEMA

1 Mains

Shield IP21

NEMA

12 Mains

Shield IP54 Cla

ss A

2

Cla

ss A

1

Gra

ph

ica

l

LC

P

Co

ati

ng

Filter Fused

DisconnectFuses

Active Filter

Control

Option

460V 480V 500V E21 E54 E2M E5M HX H4 G C 3 7 CF

AAF006-A190 190 150 95 $29,599 $2,150 $975 $2,999

STD

$2,599 ST

D

STD

$999 $475

STDAAF006-A250 250 200 125 $39,999 $2,150 $975 $2,999 $4,750 $2,199 $625

AAF006-A310 310 250 155 $46,499 $2,150 $975 $2,999 $5,250 $2,199 $625

AAF006-A400 400 320 200 $59,999 $2,150 $975 $2,999 $5,250 $2,199 $625

* See water catalog page 151 for actual current

AAF Options and accessories

[1] [2] [3] [4] [5] [6] [7] [8] [9] [10] [11] [12] [13] [14] [15] [16] [17] [18] [19]

AAF006-A - - T4 - - - X - G - C - - X - X - SXXX - X - - BX - CF - X - XX -



VLT® Drive Accessories

MCT 10 software offers advanced programming functionality for all Danfoss drive products, greatly reducing programming and setup time. Download from: http://www.danfoss.com/North_America/BusinessAreas/DrivesSolutions

Drives are managed in a standard folder-based user interface that’s familiar and easy to understand. Parameter settings for each drive are contained in a single file, allowing easy duplication of parameter sets between drives.

PC Software

Order

Number Product Type Description List Price

130B1000 MCT 10 MCT 10 set-up software (advanced version) $275

MCT 10 Comparison

MCT 10 Basic MCT 10 Advanced

Number of projects Unlimited UnlimitedNumber of drives per project 4 UnlimitedLogging and scope functions 2 channels 8 channelsReal time logging from drive N/A 4 channelsAlarm display View alarm history Alarm history in saved projectsMotor database N/A Yes

Project folders can also store user-defined files such as PDFs, CAD drawings, or Word documents. MCT 10 is the one PC tool for all your drive programming tasks.

MCT 10 Basic (available free of charge from the Danfoss web site) allows access to a finite number of drives with limited functionality. The Advanced edition, offering a higher level of functionality, is available from your Danfoss sales partner.

PC Software

Order

Number Type Description List Price

130B1000 MCT-10 VLT Software, MCT 10 set-up (1 Copy) $275.00 130B1001 MCT-10 MCT 10 set-up - PC software 5 licences $1,105.00 130B1002 MCT-10 MCT 10 set-up - PC software 10 licences $2,205.00

VLT Misc Accessories

Order

Number Description List Price

175Z0967 VLT dialog 5/6000/2800, comm, v3.0 $45.00 175Z0850 Remote LCP Kit,IP20, N1 $80.00 175N0160 LCP Remote Kit - FCM 300 series $65.00 175N0131 LCP Control Unit - VLT 2800 $175.00 175N0162 LCP Cable FCM 300 $70.00 175N0128 FCM - Motor Remote $155.00 175Z0929 Remote LCP Cable, 3m $40.00 195N3113 Cable for DeviceNet,5 Pole Conn $65.00 130B1107 LCP Graphical Control Panel $170130B1124 LCP Numberical Control Panel $170130B1158 LCP (For Electronic Bypass Only) $170130B1117 LCP Remote Mounting Kit $90176F1827 Pedestal Base 8” High for D frame Drives $1240

50 1.800.432.6367 Rev. A - May 2015

Accessories

MCD Control Panel LCP 501 175G0096 $305 MCD Modbus Module 175G9000 $215MCD Profibus Module 175G9001 $300 MCD DeviceNet Module 175G9002 $265 MCD USB Module 175G9009 $270

As standard, MCD 500 rated impulse withstand voltage is limited to 4kV. The surge protection kits protect the system and make the soft starter immune to high voltage impulses.

IP 20 Finger Guard Kit

MCD5-0131B-MCD5-0215B (G2) 175G5662 $195 MCD5-0245C (G3) 175G5663 $505 MCD5-0360C-MCD5-0927C (G4) 175G5664 $750

MCD5-1200C-MCD5-1600C (G5) 175G5665 $755

MMCD5-0021B-MCD5-105 N/A - Units are IP20

Surge Protection Kits

6kVSurge protection kit for G1 175G0100Surge protection kit G2-G5 175G0101

12kVSurge protection kit for G1 175G0102Surge protection kit G2-G5 175G0103

MCD 500 Soft Starter

[1] Amperage rating [5] Reserved

0021- 1600 (10-1100 HP) X = Not used

[2] Bypass Rating [6] IP Rating

B = Bypassed (21 – 215 amp only) 00 = Open Chassis/IP00

C = Non-Bypassed 20 = Protected Chassis/IP20

[3] Mains Voltage [7] Control Voltage

T5 = 200 - 525 VAC CV1 = 24 VAC / VDC

T7 = 380 – 690 VAC CV2 = 110-120 VAC

OR

[4] Frame Size 220 – 240 VAC

G1 = 21 ~105 amps

G2 = 131 ~ 215 amps

G3 = 245 amps

G4 = 360 ~ 927 amps

G5 = 1200 ~ 1600 amps

VLT® Soft Starter MCD 500 is a total motor starting solution. Current transformers measure motor current and provide feedback for controlled motor ramp profiles.

AAC, the Adaptive Acceleration Control, automatically employs the best starting and stopping profile for the application. Adaptive Acceleration Control means

[1] [2] [3] [4] [5] [6] [7]

MCD5 0021 - B - T5 - G1 - X - 20 - CV2

How to Order:

Choose the Normal or Heavy Duty Rating that is best suited to the application.Find the Continuous Amp value that is greater than or equal to the motor’s nameplate value.

Order Example:

that for each start and stop, the soft starter compares and adapts the process to the chosen profile best suited to the application.

The VLT® Soft Starter MCD 500 has a four-line graphical display and a logic keypad making programming easy. Advanced setup is possible displaying operational status.

MCD 501 Keypad

• Dedicated 9-pin output on MCD500

• Simple remote display

• One part number (175G0096) includes LCP with door mount kit and cable

• Powered by Soft Starter

• All functions available on the MCD500 unit are also available via the LCP 501

• IP65 (NEMA 3R) solid encapsulation protection

• Plug & Play

For Use with MCD 500 unit only

* BP denotes integrally bypassed unit NBP denotes externally bypassed unit Bypass Contactor by others

** Dual current rating denote non-bypassed current rating and bypassed current rating.


*AC-53 Rating for Control Voltage

CV1 = 24 VAC/VDC CV2 = 110 or 220 VAC


MCD 500 Softstarter with Bypass 200 - 240 V (T5)

Frame Description

Current Ratings Part Number

List Price

Light Med Heavy Severe Duty

*AC53b 3.0-20:340

*AC53b 4.0-20:340

*AC-53b 4.5-30:330

*AC-53b;4.5-30:420

55�CCV1 CV2

G1B No Fan

MCD5-0021B-T5-G1X-20-

CV_22 17 15 13 175G5500 175G5525 $940

MCD5-0037B-T5-G1X-20-

CV_39 30 25 23 175G5501 175G5526 $1,095

MCD5-0043B-T5-G1X-20-

CV_46 35 29 26 175G5502 175G5527 $1,110

MCD5-0053B-T5-G1X-20-

CV_53 44 35 32 175G5503 175G5528 $1,125

MCD5-0068B-T5-G1X-20-

CV_68 52 43 39 175G5504 175G5529 $1,165

MCD5-0084B-T5-G1X-20-

CV_84 64 53 48 175G5505 175G5530 $1,375

MCD5-0089B-T5-G1X-20-

CV_89 68 56 50 175G5506 175G5531 $1,540

MCD5-0105B-T5-G1X-20-

CV_105 87 70 64 175G5507 175G5532 $1,695

G2B

MCD5-0131B-T5-G2X-00-

CV_130 100 84 76 175G5508 175G5533 $2,125

MCD5-0141B-T5-G2X-00-

CV_132 101 80 75 175G5509 175G5534 $2,400

MCD5-0195B-T5-G2X-00-

CV_193 147 121 109 175G5510 175G5535 $2,895

MCD5-0215B-T5-G2X-00-

CV_206 163 134 122 175G5511 175G5536 $2,995

G3B

MCD5-0245B-T5-G3X-00-

CV_246 189 164 145 134N9344 134N9345 $3,899

MCD5-0331B-T5-G3X-00-

CV_334 256 218 195 134N9348 134N9349 $4,299

MCD5-0396B-T5-G3X-00-

CV_399 307 261 235 134N9352 134N9353 $4,999

G4B

MCD5-0469B-T5-

G4X-00-CV_469 362 305 275 134N9356 134N9357 $5,699

MCD5-0525B-T5-

G4X-00-CV_518 406 345 309 134N9360 134N9361 $6,375

MCD5-0632B-T5-

G4X-00-CV_623 480 409 368 134N9364 134N9365 $7,199

MCD5-0744B-T5-

G4X-00-CV_733 564 476 429 134N9368 134N9369 $8,199

MCD5-0826B-T5-

G4X-00-CV_809 622 515 466 134N9372 134N9373 $9,799

MCD5-0961B-T5-

G4X-00-CV_941 724 600 542 134N9376 134N9377 $11,650

52 1.800.432.6367 Rev. A - May 2015

MCD 500 Softstarter without Bypass 200 - 240 V (T5)

Frame Description

Current Ratings **Part Number

List Price


*AC53b 3.0-20:340

*AC53b 4.0-20:340

*AC-53b 4.5-30:330

*AC-53b;4.5-30:420 55 C

CV1 CV2

G3CMCD5-

0245C-T5-G3X-00-CV_

236/247 189/197 165/171 147/152 175G5512 175G5537 $3,100

G4C

MCD5-0360C-T5-

G4X-00-CV_354/360 292/302 253/259 223/228 175G5513 175G5538 $3,200

MCD5-0380C-T5-

G4X-00-CV_380/380 330/347 284/293 247/255 175G5514 175G5539 $3,275

MCD5-0428C-T5-

G4X-00-CV_405/429 338/355 292/302 254/264 175G5515 175G5540 $3,425

MCD5-0595C-T5-

G4X-00-CV_544/584 470/502 398/416 346/362 175G5516 175G5541 $4,200

MCD5-0619C-T5-

G4X-00-CV_565/610 485/520 415/434 361/379 175G5517 175G5542 $4,775

MCD5-0790C-T5-

G4X-00-CV_761/790 649/679 547/563 475/489 175G5518 175G5543 $5,995

MCD5-0927C-T5-

G4X-00-CV_858/913 739/784 618/640 530/550 175G5519 175G5544 $8,695

G5C

MCD5-1200C-T5-

G5X-00-CV_1200/1200 1041/1151 925/1003 799/871 175G5520 175G5545 $11,995

MCD5-1410C-T5-

G5X-00-CV_1282/1410 1079/1191 957/1036 835/908 175G5523 175G5546 $14,525

MCD5-1600C-T5-

G5X-00-CV_1506/1600 1283/1438 1136/1244 990/1090 175G5524 175G5547 $17,375



MCD 500 Soft StarterMCD 500 Softstarter with Bypass 380 - 690 V (T7)

Frame Description

Current Ratings Part Number

List PriceLight Med Heavy Severe Duty

*AC53b 3.0-20:340

*AC53b 4.0-20:340

*AC-53b 4.5-30:330

*AC-53b;4.5-30:420

55�CCV1 CV2

G1B

MCD5-0021B-T7-G1X-20-CV_ 22 17 15 13 175G5548 175G5571 $940

MCD5-0037B-T7-G1X-20-CV_ 39 30 25 23 175G5549 175G5572 $1,095

MCD5-0043B-T7-G1X-20-CV_ 46 35 29 26 175G5550 175G5573 $1,110

MCD5-0053B-T7-G1X-20-CV_ 53 44 35 32 175G5551 175G5574 $1,125

MCD5-0068B-T7-G1X-20-CV_ 68 52 43 39 175G5552 175G5575 $1,165

MCD5-0084B-T7-G1X-20-CV_ 84 64 53 48 175G5553 175G5576 $1,375

MCD5-0089B-T7-G1X-20-CV_ 89 68 56 50 175G5554 175G5577 $1,540

MCD5-0105B-T7-G1X-20-CV_ 105 87 70 64 175G5555 175G5578 $1,695

G2B

MCD5-0131B-T7-G2X-00-CV_ 130 100 84 76 175G5556 175G5579 $2,125

MCD5-0141B-T7-G2X-00-CV_ 132 101 80 75 175G5557 175G5580 $2,400

MCD5-0195B-T7-G2X-00-CV_ 193 147 121 109 175G5558 175G5581 $2,895

MCD5-0215B-T7-G2X-00-CV_ 206 163 134 122 175G5559 175G5582 $2,995

G3B

MCD5-0245B-T7-G3X-00-CV_ 246 189 164 145 134N9346 134N9347 $3,899

MCD5-0331B-T7-G3X-00-CV_ 334 256 218 195 134N9350 134N9351 $4,299

MCD5-0396B-T7-G3X-00-CV_ 399 307 261 235 134N9354 134N9355 $4,999

G4B

MCD5-0469B-T7-G4X-00-CV_ 469 362 305 275 134N9358 134N9359 $5,699

MCD5-0525B-T7-G4X-00-CV_ 518 406 345 309 134N9362 134N9363 $6,375

MCD5-0632B-T7-G4X-00-CV_ 623 480 409 368 134N9366 134N9367 $7,199

MCD5-0744B-T7-G4X-00-CV_ 733 564 476 429 134N9370 134N9371 $8,199

MCD5-0826B-T7-G4X-00-CV_ 809 622 515 466 134N9374 134N9375 $9,799

MCD5-0961B-T7-G4X-00-CV_ 941 724 600 542 134N9378 134N9379 $11,650

MCD 500 Softstarter without Bypass 380 - 690 V (T7)

Frame Description

Current Ratings **Part Number

List Price


*AC-53b 3.0-30:330

*AC-53b 4.0-20:340

*AC-53b 4.5-30:330

*AC-53b;4.5-30:420

55�CCV1 CV2

G3C MCD5-0245C-T7-G3X-00-CV_ 236/247 189/197 165/171 147/152 175G5560 175G5583 $3,100

G4C

MCD5-0360C-T7-G4X-00-CV_ 354/360 292/302 253/259 223/228 175G5561 175G5584 $3,200

MCD5-0380C-T7-G4X-00-CV_ 380/380 330/347 284/293 247/255 175G5562 175G5585 $3,275

MCD5-0428C-T7-G4X-00-CV_ 405/429 338/355 292/302 254/264 175G5563 175G5586 $3,425

MCD5-0595C-T7-G4X-00-CV_ 544/584 470/502 398/416 346/362 175G5564 175G5587 $4,200

MCD5-0619C-T7-G4X-00-CV_ 565/610 485/520 415/434 361/379 175G5565 175G5588 $4,775

MCD5-0790C-T7-G4X-00-CV_ 761/790 649/679 547/563 475/489 175G5566 175G5589 $5,995

MCD5-0927C-T7-G4X-00-CV_ 858/913 739/784 618/640 530/550 175G5567 175G5590 $8,695

G5C

MCD5-1200C-T7-G5X-00-CV_ 1200/1200 1041/1151 925/1003 799/871 175G5568 175G5591 $11,995

MCD5-1410C-T7-G5X-00-CV_ 1282/1410 1079/1191 957/1036 835/908 175G5569 175G5592 $14,525

MCD5-1600C-T7-G5X-00-CV_ 1506/1600 1283/1438 1136/1244 990/1090 175G5570 175G5593 $17,375

** Dual current ratings denote non-bypassed current rating and bypassed current rating

54 1.800.432.6367 Rev. A - May 2015

General Conditions of Sale and WarrantyGeneral Conditions of Sale and Warranty

These General Terms and Conditions of Sale (“Terms”) apply to all deliveries of products and services (“Products”) from Danfoss LLC or its Affiliates (each of which is referred to as “Danfoss”) to any customer (“Customer”). In these Terms “Affiliate” shall mean any entity that directly or indirectly through one or more intermediaries, controls, is controlled by or is under common control by Danfoss LLC at such time. No terms and conditions other than these Terms shall be binding upon Danfoss and the Customer unless agreed in writing by both Danfoss and Customer. All terms and conditions contained in any prior communication which are different from or in addition to the Terms shall not be binding on Danfoss unless otherwise expressly agreed in writing by both Danfoss and Customer.1. Confirmation of Order

Danfoss shall not be deemed to have accepted an order until a written, including electronic, acceptance of the Customer’s purchase order by Danfoss is received by Customer or Danfoss has received a written, including electronic, timely and unconditional acceptance by Customer of Danfoss’ quotation.2. Terms of Delivery

The Products are delivered F.O.B. Seller, [freight and insurance prepaid and add]. If the Customer does not provide written instructions, Danfoss may deliver the Products to Customer, at the risk and expense of Customer, by a transport method chosen by Danfoss. Unless otherwise agreed in writing, Danfoss may make delivery in installments. All installments will be separately invoiced and paid as billed without regard to subsequent deliveries. Failure to pay any installment when due will excuse Danfoss from making all future deliveries.3. Shipment Delay

If Danfoss does not ship on the promised date, Customer is entitled to request a reasonable, revised shipment date in writing without undue delay. No claims can be made by the Customer as a result of the delay. 4. Price

Prices for Products do not include taxes or duties. Danfoss reserves the right to adjust accepted prices for non-delivered Products in the event of alterations in rates of exchange, variations in costs of materials, a sub-supplier’s price increases, changes in wages, state requisitions or similar conditions over which Danfoss has no or limited control.5. Packing

Disposable packing is not included in the price and will not be credited if returned. Cost of special boxing, export boxing, cartage or transfer expenses will be added to the invoice unless charges are shown to be included in the prices quoted.6. Terms of Payment

Invoices are payable in full 30 days following the invoice date unless other payments terms are agreed to in writing between Danfoss and the

Customer, subject to approval and continuance of approval of credit by Danfoss. In the event that Danfoss does not approve credit to the Customer, or if at any time Danfoss reverses its prior approval of credit for any reason, terms of payment shall be C.O.D., or immediate partial, or full advance payment, or a combination of the foregoing methods, all as Danfoss may then, or thereafter from time to time, elect or specify. All payments shall be in U.S. dollars. Invoices not paid within 30 days of the invoice date are subject to an interest rate of the lesser of 1½% per month or the highest rate allowable under applicable law.7. Group Set-off

Danfoss and its Affiliates shall be entitled to set off their own claims against the Customer, in event of Customer’s possible claims against any of said companies. 8. Product Information

While Danfoss attempts to provide helpful and accurate information on the weight, dimensions, capacity, and performance capabilities of the Products in catalogues, literature, brochures and advertisements, and on its website, the Customer should not rely on any such information, and no such information is binding on Danfoss, unless explicit reference to the specific information in question is made in a written offer from Danfoss and/or a written order acceptance by Danfoss. Specific demands from the Customer are only binding if and to the extent they have been accepted by Danfoss in writing.9. Proprietary Information and

Confidentiality

Any non-public information, including but not limited to, drawings, descriptions and any other technical documents which Danfoss makes available to the Customer (“Confidential Information”) shall remain the property of Danfoss and shall be treated as confidential by Customer and its representatives and must not, without the written consent of Danfoss, be copied, reproduced, or transferred to third parties or be used for other purposes than those intended when the Confidential Information was made available. Confidential Information shall be returned upon Danfoss’ request. 10. Alterations

Danfoss reserves the right to make, without notice to Customer, alterations to a Product that do not materially affect agreed specifications or the Product’s form, fit or function.11. Limited Warranty

11a Danfoss warrants that VLT Variable Frequency Drives, AC VFD Panels and Harmonic Filters, except VLT Micro Drive, Decentral Drives, Soft Starters and their options to be free from defects in material and workmanship for 18 months from date of shipment. DrivePro Plus units are warranted for 36 months from date of shipment. 11b Danfoss warrants that VLT Micro Drive, Decentral Drives and Soft Starters and their options will be free from defects in materials

and workmanship for a period of 12 months from date of shipment. 11c Accessories for all drives ordered for shipment subsequent to the drive and all items mounted separate from the drive will be free from defects in materials or workmanship for a period of 12-month, from date of shipment.11d All drives parts will be free from defects in materials or workmanship for a period of 6–months from date of shipment.This warranty shall be voided if the article in question is improperly installed, applied, operated or maintained; subjected to overload, misuse, negligence or an accident; or repaired or altered outside of the Danfoss factory or by anyone other than an authorized Danfoss service partner under direction of Danfoss. Products manufactured by others, but supplied by Danfoss as part of a Danfoss Product, are not warranted by Danfoss, and Customer’s sole recourse if any such product should fail shall be under the warranty, if any, of such other manufacturer. Fuses are warranted only when a defect or malfunction of the Product or its components are found to be the cause of the fuse failure. Customer’s sole and exclusive remedy against Danfoss and Danfoss’ only obligation, for breach of warranty, shall be, at Danfoss’ option, the repair or replacement (with either a refurbished or new Product) of any Product that on Danfoss’ examination is found to be defective at the time of delivery due to faulty workmanship and/or defective material, but only if the Customer submits a claim in writing to Danfoss within the warranty period. When making a warranty claim, the Customer must forward the Product to Danfoss in a manner to be agreed upon between Customer and Danfoss with a description of the reason for returning the Product. Freight and insurance will be paid by the Customer. If Danfoss’ determines that the Product is not defective due to faulty workmanship and/or defective material or that the warranty has been voided, the Product shall be returned to the Customer, if the Customer requests. In such case, freight and insurance shall be paid by the Customer. If Danfoss ascertains that the Product is defective due to faculty workmanship and/or defective material, Danfoss shall send the repaired Product or a replacement Product to the Customer. Danfoss may choose the method of delivery and will pay freight and insurance. Products or product parts which have been replaced shall be the property of and retained by Danfoss. The Customer is responsible for repackaging Products returned in suitable packing material to prevent damage in transit. Danfoss may elect to provide service personnel at Customer’s premises to affect Product repair or replacement covered by the terms of the warranty. Danfoss may pay for a portion or all of the travel time and expense for Products located in the 48 adjacent states; island of Oahu, Hawaii;


Anchorage, Alaska; and major metropolitan areas of Canada. For products located in the rest of Hawaii, Alaska, Canada and other countries, travel time and travel expenses will be billed to the Customer. 12. Disclaimer of Warranties

EXCEPT FOR THE WARRANTIES STATED IN SECTION 11, THE PRODUCTS ARE SUPPLIED “AS IS”, “WHERE IS” AND “WITH ALL FAULTS”. DANFOSS DISCLAIMS ALL OTHER WARRANTIES WITH RESPECT TO THE PRODUCTS, EITHER EXPRESS OR IMPLIED, ARISING BY OPERATION OF LAW, COURSE OF DEALING, USAGE OF TRADE OR OTHERWISE, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. 13. Indemnification

Customer shall indemnify, defend and hold Danfoss harmless from all claims, including but not limited to all claims filed by third parties, for injuries, harms, losses or damages of any kind, (a) caused by or resulting from, (i) the Product after it has been delivered, (ii) the improper use, repair, maintenance or operation of the Product by Customer, (iii) the failure of Customer to adequately train personnel in the operation of the Product, or (iv) the Customer’s failure to comply with applicable laws or regulations or (b) to products manufactured by the Customer or to products of which the Customer’s products form a part. The Customer consents to the jurisdiction of any court or arbitral tribunal in which any third party files a claim for injuries, harms, losses or damages allegedly caused by any Product sold to Customer.14. Limitation of Liability

IN NO EVENT SHALL DANFOSS BE LIABLE FOR ANY SPECIAL, INDIRECT, CONSEQUENTIAL, PUNITIVE OR EXEMPLARY DAMAGES OR LOSSES ARISING OUT OF ANY BREACH OF WARRANTY, FAULTY PRODUCT, DELAY IN THE DELIVERY OF THE PRODUCT, PRODUCT LIABILITY, FAILURE TO WARN, RECALL OR OTHERWISE, IRRESPECTIVE OF THE CAUSE, INCLUDING BUT NOT LIMITED TO, LOSS OF PRODUCTION, LOSS OF PROFIT AND LOSS OF GOODWILL. 15. Notice of Claims

Claims or complaints as to defects and/or delay in delivery of the Products or other claims shall be submitted in writing by Customer to Danfoss without undue delay.16. Intellectual Property Rights

If the Product is delivered with embedded software, Customer obtains a non-exclusive, software license in form of a right to use the software solely for the purposes set out in the applicable specification of the Product. Aside from this, Customer obtains no rights in form of license, patent, copyright, trademark or other proprietary right connected to the Products. Customer shall not obtain any rights to source codes to such software. Danfoss, at its’ election, may defend any suit or proceeding brought against Customer as far as the same is based on a claim that any Product of

Danfoss’ design furnished hereunder or any part thereof, constitutes an infringement of any United States or Canadian patent, if notified promptly in writing and given authority, information and assistance for the defense of the same and if such alleged infringement is not the result of the design or other special requirements specified by Customer or the application or use to which such Product is put to use by Customer or others. In the event that Danfoss elects to defend such suit or proceeding, Danfoss will pay all damages and costs awarded in such suit or proceeding against Customer. In the event that such Product or part in such suit is held to infringe any such patent and use thereof is enjoined, Danfoss will, at its option, (a) procure Customer with the right to continue use of such Product or part, (b) replace same with non-infringing Product(s) or parts, (c) modify the same so that it becomes non-infringing, or (d) remove said Product or part and refund the purchase price and the transportation and installation costs thereof. The foregoing states the entire liability of Danfoss to Customer for patent infringement. 17. Export

Customer is hereby advised and put on notice that Products may be subject to export controls and regulations of the United States, another country of manufacture or a country of transshipment, and export may require a valid export license. Danfoss’ acceptance of Customer’s order and delivery of the Products is expressly conditioned on compliance by Customer with all applicable export controls. Danfoss is under no obligation to sell or deliver the Products until all required export licenses have been granted. No Products sold to Customer may be exported unless such export complies fully with all applicable export regulations. Customer shall be responsible for obtaining all required export licenses and for all expenses of obtaining such licenses.18. Prohibition on Resale and Use for Certain

Purposes

Danfoss Products are produced exclusively for civilian use. Customer is not allowed to use or to resell the Products for purposes which have any connection to chemical, biological or nuclear weapons or for missiles which are capable of delivering such weapons. Customer is not allowed to sell the Products to persons, companies or any other kind of organization if Customer has knowledge of or suspects that said persons or entities are related to any kind of terrorist or narcotics activities. The Products may be subject to legal regulations and restrictions and may therefore be subject to restrictions in case of sale to countries/customers covered by export and import ban. These restrictions shall be observed in case of resale of the Products to such countries/customers. Customer is not allowed to resell the Products if there is doubt or suspicion that the Products can be used for the purposes mentioned in the preceding paragraph. If Customer receives knowledge of or suspects that the conditions in

this clause have been violated, Customer shall immediately inform Danfoss. 19. Force Majeure

Danfoss is entitled to cancel orders or suspend or delay delivery of Products and will not be liable for such cancellation, suspension, or any non-delivery, faulty or delayed delivery which partly or wholly is caused by circumstances beyond Danfoss’ control, including, but not limited to, riots, civil unrest, war, terrorism, fire, insurrection, requisition, seizure, embargo or defects or delays in deliveries by sub-contractors, strikes, lockouts, slow downs, lack of transportation, scarcity of materials, accidents in product testing, and insufficient supplies of energy. Any of Customer’s contractual rights are suspended or become void in any such circumstances referred to in this clause. Customer is not entitled to any kind of damages or to make a claim whatsoever in case of cancellation or delayed delivery due to such circumstances.20. Global Compact

Danfoss has joined the United Nations’ Global Compact initiative which means that Danfoss has undertaken to live up to 10 principles on human rights, employees’ rights, the environment and corruption. These principles are listed in “Danfoss Code of Conduct for Suppliers” to be seen on www.danfoss.com. Therefore Danfoss encourages the Customer to comply with these fundamental principles. For further information on Global Compact: http://www.unglobalcompact.org21. Partial Invalidity

If one or more of the terms and conditions in these Terms or any part of a term is deemed invalid, unenforceable, illegal or inoperable, the validity, enforceability, legality or operability of all further terms and conditions shall not be affected or diminished thereby.22. Disputes

Any dispute between the parties concerning or arising from (a) a purchase of a Product or (b) any damages, injuries, losses or harms allegedly caused by any Product shall be decided under Wisconsin law. Any such dispute which the parties themselves are unable to resolve shall be referred to and settled by arbitration in Chicago, Illinois under the American Arbitration Association’s Commercial Arbitration Rules (“AAA Rules”) by one arbitrator appointed in accordance with said AAA Rules. The Parties may refer the enforcement of any arbitral award to any competent court. English shall be the language to be used in the arbitration proceeding unless otherwise agreed between the parties. The arbitration proceedings and the arbitral award shall be confidential and involved persons on both sides are pledged to secrecy.

175R5515 Rev. A© Copyright 2015 by Danfoss 05/15

Danfoss can accept no responsibility for possible errors in catalogs, brochures and other printed material. Danfoss reserves the right to alter its products without notice. This also applies to products already on order provided that such alterations can be made without subsequent changes being necessary in specifications already agreed. All trademarks in this material are property of the respective companies. Danfoss and the Danfoss logotype are trademarks of Danfoss A/S. All rights reserved.

www.danfossdrives.com

Danfoss Drives

4401 N. Bell School Rd.Loves Park, IL 61111, USAPhone: 1.800.432.6367 1.815.639.8600Fax: 1.815.639.8000

EnVisioneeringAs a world leader in components and solutions, Danfoss meets our customers’ challenges through “EnVisioneering.” This approach expresses our views on engineer-ing innovation, energy efficiency, environmental responsibility and sustainable business growth that create strong customer partnerships. This vision is realized through a global production, sales, and service network focused on refrigeration, air conditioning, heating and water, and motion control. Through EnVisioneering, Danfoss is Making Modern Living Possible.Danfoss “EnVisioneering”:

Engineered solutions to improve performance and profitability Energy efficiency to meet higher standards and to lower operating costs Environmental sustainability to provide a financial and social payback Engaged partnerships to foster trust, reliability, and technological superiority

Danfoss Drives

8800 W. Bradley Rd.Milwaukee, WI 53224, USAPhone: 1.800.621.8806 1.414.355.8800Fax: 1.414.355.6117