Visual PLC5.7" display, EtherNet/IP™ - VT250 serie (Economy)VT250-57C-L7-IPM
Edi
tion
• 201
7-06
-25T
16:3
6:46
+02:
00
1 / 3 Hans Turck GmbH & Co.KG ñ D-45472 Mülheim an der Ruhr ñ Witzlebenstraße 7 ñ Tel. 0208 4952-0 ñ Fax 0208 4952-264 ñ [email protected] ñ www.turck.com
Type designation VT250-57C-L7-IPMIdent no. 6828017
Function PLC with integrated touch display
Display / TouchDisplay TFT LCD colour displayTouch ResistiveActive screen area 5.7'' (approx. 118 * 89 mm)Resolution (pixels) 320 × 240 (240 * 320 with edgewise design)Number of usable colours 65536 colours
ControllerProcessor ARM9, 32 bit, 200 MHzProgram and data memory 4 MB (CoDeSys and QViS)Remanent memory 16 kB SDRAMAdd-on memory 1 x SD/MMC memory cardReal time clock yesOperating system rcX
Programming CODESYS V.3
InterfacesEthernet Double (integrated switch)Protocols EtherNet/IP™ (Scanner/Master)
Modbus RTU (Master/Slave)USB DeviceSerial RS232 / RS485
Power supplyRated value 24 VDC reverse-polarity protected, 0.35 A maximumAdmissible voltage range 20.4…28.8VDC
General dataOperating ambient conditions 0…50 °C, 10…90 % relative humidity, non-condens-
ingStorage ambient conditions -20…60 °C, 10…95 % relative humidity, non-con-
densingApprovals CE, cULusProtection class IP65 front
IP20 rear
DimensionsFront (W x H x D) 212x156x50mmCut-out (W x H) 198x142mmWeight approx. 0.7 kg
■ TFT LCD color display
■ 5.7", 320 × 240 pixels, 65 K colors
■ Resistive Touch
■ 2 x RJ45 real-time Ethernet interface
■ Serial interface RS232/485 and USB de-vice
■ EtherNet/IP™ master
■ Programmable with CODESYS V3 acc.toIEC 61131-3
■ 32 Bit RISC processor 200 MHz
■ 4 MB program and data memory(CODESYS and QViS project files)
■ 16 kB non-volatile memory
■ SD/MMC memory card
■ Protection class IP65, front face
The HMI touch panel with a 5.7“ TFT displaycan be used both as operator and control ter-minal. The control software applied is CoDeSys V3and approved according to the internationalstandard IEC 61131-3. QViS is the software used for visualizationand especially developed for embedded sys-tems.
The exchange of variables between controlunit and visualization is implemented via inter-face. The HMI panel is equipped with all rele-vant RT Ethernet and fieldbus systems.
Visual PLC5.7" display, EtherNet/IP™ - VT250 serie (Economy)VT250-57C-L7-IPM
Edi
tion
• 201
7-06
-25T
16:3
6:46
+02:
00
2 / 3 Hans Turck GmbH & Co.KG ñ D-45472 Mülheim an der Ruhr ñ Witzlebenstraße 7 ñ Tel. 0208 4952-0 ñ Fax 0208 4952-264 ñ [email protected] ñ www.turck.com
Connection and pin assignment
Power SupplyNominal voltage 24 VDCNominal current 0.35 A
Pin Assignment
CAN / DeviceNet™ Fieldbus InterfacePluggable terminal strip, 5-pole
Pin Assignment
Ethernet Ports2 x RJ45 jackIntegrated switch10/100 Mbps
Pin Assignment
RS232 InterfaceSUB-D male connector, 9-poleAttention:Do not connect pins 1, 4, 6 and 9 when using RS232!
Pin Assignment
Visual PLC5.7" display, EtherNet/IP™ - VT250 serie (Economy)VT250-57C-L7-IPM
Edi
tion
• 201
7-06
-25T
16:3
6:46
+02:
00
3 / 3 Hans Turck GmbH & Co.KG ñ D-45472 Mülheim an der Ruhr ñ Witzlebenstraße 7 ñ Tel. 0208 4952-0 ñ Fax 0208 4952-264 ñ [email protected] ñ www.turck.com
USB InterfaceUSB deviceService interface
Pin Assignment