8/6/2019 5962 User Manual
1/72
NCR 5962 Wedge Touch ScreenRelease 1.0
Users Guide
BD20-1371-BIssue F
8/6/2019 5962 User Manual
2/72
The produ ct described in this book is a licensed p rodu ct of NCR Corporation.
NCR is a registered trademark of N CR Corporation.
It is the policy of NCR Corporation (NCR) to improve prod ucts as new techn ology, comp onents, softw are,and firmware become available. NCR, therefore, reserves the right t o change specifications w ithout pr iornotice.
All features, functions, and operations d escribed herein may not be m arketed by N CR in all parts of theworld. In some instances, photographs are of equipment prototypes. Therefore, before using this document,consult w ith your N CR representative or NCR office for information th at is app licable and curr ent.
To maintain the qu ality of ou r pu blications, we need you r comm ents on the accuracy, clarity, organizat ion,and value of this book.
Add ress correspondence to:
Manager, Information ProductsNCR Corporation2651 Satellite Blvd.Dulu th, GA 30096
Copyr ight 2000By N CR CorporationDayton , Ohio U.S.A.All Rights Reserved
8/6/2019 5962 User Manual
3/72
i
PrefaceSafety RequirementsCaution: This dev ice shou ld on ly be powered by a (SELV) SafetyExtra Low Voltage pow er sup p ly source with an available pow er levelof 5 amperes or less, and su itable for the coun try of installation. Thepower sou rce mu st be certified by the ap prop riate safety agency for the
country of installation.Attention : Le matriel doit tre relis electriquement au circuit TrsBasse Tension de Scur it (TBTS) ayan t une limite d e 5 amp rescorrespon dant d e faon satisfaisan te et accep table dan s le pays o lematril doit tre install. Le sou rce dalim entation d oit tre app rovepar un e agence de norm alisation ap prop rie et acceptable dans le payso le matriel doit tre install.
Caution: For continu ed p rotection against risk of fire, replace onlywith the same type and ratings of fuse.
Attention : Pour p rvenir et vous protger contre un risque de feu,remplacer la fusible avec un e autre fusible de mm e type, seulem ent.
Caution: The p ower sup ply cord is used as the m ain disconnectdevice. Ensure that the socket ou tlet is located / installed n ear theequ ipm ent an d is easily accessible.
Attention : Le cordon dalimentation est utilis comm e interrupteurgnra l. La prise de couran t doit tre situe ou installe a proximite dumatriel et tr e facile d accs.
Audience
This man u al is w ritten for hard ware installer/ service personnel,system integrators, programmers, and field engineers.
8/6/2019 5962 User Manual
4/72
ii
8/6/2019 5962 User Manual
5/72
iii
Table of Contents
Chapter 1: Introduction
Com patibility ................................................................ 1-2Featu res ......................................................................... 1-2
Wed ge Con troller ................................................... 1-3Du al-Color Pow er LED .......................................... 1-3Keylock.................................................................... 1-3NCR 7450 Stand by Sleep Switch ....................... 1-4Three-Track MSR.................................................... 1-4Speaker ................................................................... .1-4
Externa l Stand ard PC Keyboard Conn ector ......... 1-4
Extern al RS-232 Scanner Connector ...................... 1-4
Chapter 2: Site Preparation
Physical Environ m ent ..................................................2-1
Op era ting Range ................................................2-1
Storag e Range ..................................................... 2-1
Tran sit Range ......................................................2-1Electrical Environment ................................................. 2-2
Pow er Consump tion .......................................... 2-2
Cable Leng th Limitation s ............................................. 2-2
Dim ensions................................................................... .2-3
Chapter 3: Installation
PCI LCD Card ......................................................... 3-2
Setting the Panel Select Switch (SW1)............... 3-2
Wed ge LCD AT Card ............................................. 3-3
Setting th e Board I/ O Ad dress (SW2) .............. 3-3
8/6/2019 5962 User Manual
6/72
iv
Setting the RS-232 I/ O Ad dress (SW1)............. 3-4
Setting the IRQ (SW1) ....................................... .3-5Op tional RS-232 Break Ou t Por t........................ 3-5
Setting DIP Switches (3xxx 686) ........................ 3-6
Installing the 5962................................................... 3-8
Wall Mou nt ing the 5962...................................... .3-11
Installing an Integrated 2x20 Custom er Display 3-13
Con necting to a Works tation .............................. .3-15Pow erin g Up .............................................................. .3-16
Pow er Up ............................................................. .3-16
Powering Up the Workstation afterRep lacing th e PCI LCD Board ........................ .3-16
Powering Up the Workstation after
Rep lacing th e LCD AT Board ......................... .3-16Powering Up the Workstation afterReplacing the Series 35xx Moth erboard ......... 3-16
Screen Saving Featu re ......................................... .3-17
Chapter 4: Programming
Software Driver s and Utilities .....................................4-1MicroTouch Touchscreen Drivers and Utilities ...4-1
Dev ice Interfaces ........................................................... 4-2
Wed ge Con troller Interface ................................... 4-2
Touch Screen Interface ........................................... 4-2An alog MSR Inter face ............................................ 4-3
RS-232 Interface ...................................................... 4-3PS/ 2 Keyboard Inter face........................................ 4-3
Pan el OFF/ ON Sequ ence ............................................. 4-4
PCI LCD Board (65550 Chips) ........................... 4-4
LCD AT Board (65535 Chips) ............................ 4-5
Chapter 5: Service and Repair
8/6/2019 5962 User Manual
7/72
v
Safety Requ irem ents .....................................................5-1
Problem Isolation Procedures...................................... 5-2Servicing the Touch Screen Module............................ 5-8
Op ening the Cabinet .............................................. 5-8
Interna l Com ponents .......................................... .5-11
Rep lacing Prim ary Par ts ..................................... .5-12
Replacing the Tou ch Con trol Board ............... .5-13
Replacing the Speaker..................................... .5-15Rep lacing the M SR .......................................... .5-16
Removing th e Keylock .................................... . 5-18
Removing the Touch Glass............................. .5-19Rem oving the LCD.......................................... .5-21
Reassem bling the Tou ch Screen ......................... .5-23
Spare Parts List .......................................................... .5-24
Con nectors ................................................................. .5-27
External Keyboard Connector ............................ .5-27
Extern al RS-232 Scanner Connector ................... .5-27
Touch Screen Cleaning Proced ures .......................... .5-28
Index
Revision RecordIssue Date Remarks
A 7/ 96 First p rinting
B 7/ 97 Up date to CID Driver for CRT/ LCD supportunder NT
C 9/ 97 Reprint
D 5/ 98 Added touch screen cleaning p rocedu res
E 2/ 99 Add ed Integrated 2x20 Disp lay
F 9/ 00 Ad ded Model 3500 Connection Information
8/6/2019 5962 User Manual
8/72
vi
Radio Frequency Interference Statements
Federal Communications Commission (FCC) Informat ion to UserThis equipm ent has been tested and found to comp ly with the limits for a Class Adigital device, pursua nt to Pa rt 15 of FCC Rules. These limits are designed to provid ereasonable protection against harm ful interference wh en the equipm ent is operated ina commercial environm ent. This equipm ent generates, uses, and can rad iate radiofrequency energy and , if not installed an d u sed in accordance with the instru ctionma nual, may cau se harmful interference to rad io comm un ications. Opera tion of thisequipm ent in a residential area is likely to cause interference in w hich case the u serwill be required to correct the interference at his ow n expense.
NCR is not respon sible for any rad io or television interference caused by un auth orizedmod ification of this equipment or the su bstitution or attachm ent of connecting cablesand equipm ent other t han those specified by N CR. The correction of interferencecaused by such un authorized mod ification, substitution or attachment w ill be theresponsibility of the user. The user is cautioned that chan ges or mod ifications notexpressly approved by N CR may void the u ser s authority to operate the equipment.
Canadian Department of CommunicationsThis digital appara tus d oes not exceed th e Class A limits for rad io noise emissionsfrom digital app aratus set ou t in the Radio Interference Regulations of the CanadianDepartment of Communications.
Le pr sent appareil num rique n met p as de bruits radio lectriques d passant leslimites applicables aux app areils num riques de la classe A p rescrites dans leRglement su r le brouillage rad io lectriques dict par le ministr re desCommun ications du Canada.
Voluntary Control Council For Interference (VCCI)
8/6/2019 5962 User Manual
9/72
Chapter 1: Introduction
S
14010
The NCR 5962 Wedge Touch Screen is a Liqu id Crys tal Display-based(LCD) touch screen POS device. The Touch Screen module contains a10.5-inch passive m atrix (DSTN) color LCD or active m atr ix (TFT) colorLCD. It also p rovides the following: Keylock Op tional stand by switch (with NCR 7450 only) A th ree-track ISO Mag netic Stripe Reader (MSR) Speaker External conn ectors for an externa l PC keyboard Decoded external connector for external RS-232 scanner.
The active matrix LCD is not available at all for the N CR 7450workstation. The passive matr ix modu le connects to a 7450 wor kstationusing a w edg e Y-cable. The 7450 workstation d oes not use the WedgeLCD AT or PCI LCD board s.
8/6/2019 5962 User Manual
10/72
1-2 Chapter 1: Introduction
CompatibilityThe 5962 is designed as an optional inp ut/ outpu t d evice for thefollowing workstations:
PC-based retail workstation
NCR 7453 retail works tation
NCR 7452 retail works tation
NCR 7450 Release 2.x retail worksta tion
An In tel-based PC with an available stan dard 16-bit ISA slot (theLCD board h as been tested and foun d to be comp atible with a widevariety of stand ard PCs)
An In tel-based PC with an available 5V 32-bit PCI slot
FeaturesThe 5962 contains a 10.5-inch p assive matrix (DSTN) or active m atr ix(TFT) color LCD. In ad d ition to the LCD and Touch Sensor, the u nitincludes the following featu res:
Wedg e controller Dual-color pow er/ status LED
LCD contra st control (passive matrix mod el only)
Keylock
Optional stand by sleep switch for the NCR 7450 workstation
Three-track ISO Magn etic Strip e Reader (MSR) Speaker (separate from the PC speaker)
External stand ard PC keyboard connector
External decoded RS-232 scanner connector
8/6/2019 5962 User Manual
11/72
Chapter 1: Introduction 1-3
Wedge ControllerThe Wedge controller consists of a microcontroller an d associatedcircuitry that perm its (via a PC stand ard keyboard interface) theTouch Screen LCD to supp ort the following p eripheral d evices: A three-track MSR Decoded RS-232 Scann er Keylock SpeakerThe controller logically conn ects these dev ices in series with a standardPC keyboard . The retail workstation or PC interpr ets the data flow askeyboard inpu t. For more inform ation on the Wedge, refer to the NCRWedge Software Users Guide, BD20-1368-A.
Dual-Color Power LEDOn the front of the 5962 is a d ual-color LED, used to show the cu rrentstatus.
Color Status
Green LCD power on
Red Wed ge con troller rep orting an error con dition
Oran ge* LCD in stan d by m od e
Off LCD power off or 7450 in sleep mode
Note: The LED may also be orang e for a few second s on p ower -upbefore display is active.
KeylockThe 5962 includes a Keylock, accessible through the Wedge controller.There are four p ositions:
Abbreviation Position Description
Ex Excep tion Perform low level w orkstation p rogram ming,such as d iagnostics, configu ration, and load ing.
L Locked Prohibits keyboard inpu t.
8/6/2019 5962 User Manual
12/72
8/6/2019 5962 User Manual
13/72
Chapter 2: Site Preparation
Physical EnvironmentThe physical environm ents requ ired for the 5962 m odu le, the LCD ATboard , and the PCI LCD board are listed in this section.
Operating Range
Condition Range
Temperatu re 5 to 45 CRela tive Humid ity 35% to 60% (Non-condensing)
Atmospheric Pressure 3000 meters (max.)
Storage Range
Condition RangeTemperatu re -10 to 50 C
Relative H um id ity 10% to 90%
Transit Range
Condition RangeTemperatu re -40 to 60 C (One w eek max.)
Relative H um id ity 5% to 95%
8/6/2019 5962 User Manual
14/72
2-2 Chapter 2: Site Preparation
Electrical Environment
Voltage Tolerance Current (Typical) Current (Max)
5962 Module +12 V Supp ly Voltage 10% 800 mA 1300 mA
+5V Externa lKeyboard Voltage
10% N/ A 250 mA
+5V External Scann erVoltage
10% N/ A 250 mA
LCD AT Card +5V Supply Voltage 10% 900 mA 1200 mA
+12V Sup p ly Voltage 10% 0.5 mA 1.0 m A
-12V Supp ly Voltage 10% 0.06 mA 0.1 m A
LCD PCI Card +5V Supply Voltage(PCI Bus)
5% 500 mA 1500 mA
Note: +12V is not u sed by the PCI LCD board . How ever, the boarddoes pass the +12V through to the 5962 by way of the disk harn ess.
Power ConsumptionTypical Maximum
5962 Module 9.6 W 15.6 W
LCD AT Card 4.5 W 6 W
LCD PCI Card 2.5 W 7.5 W
Cable Length LimitationsConfiguration Length
Connected to an LCD Board 4 m (13 ft )
Connected to an NCR 7450 2 m (6.5 ft)
8/6/2019 5962 User Manual
15/72
Chapter 2: Site Preparation 2-3
Dimensions
14479
S
31 cm(12.2 in.)
6.5 cm(2.56 in.)
34 cm(13.4 in.)
28 cm(11.0 in.)
8/6/2019 5962 User Manual
16/72
2-4 Chapter 2: Site Preparation
8/6/2019 5962 User Manual
17/72
Chapter 3: Installation
Caution: This dev ice shou ld on ly be powered by a (SELV) SafetyExtra Low Voltage pow er sup p ly source with an available pow er level
of 5 amperes or less, and su itable for the coun try of installation. Thepower sou rce mu st be certified by the ap prop riate safety agency for thecountry of installation.
Attention : Le mat riel doit tre reli s electriquemen t au circuit Tr sBasse Tension de S curit (TBTS) ayan t une limite de 5 amp rescorrespond ant d e fa on satisfaisante et accep table dan s le pays o lemat riel doit tre install . Le sou rce d alimentation doit tre app rov epar u ne agence de norm alisation app ropri e et accep table dan s le payso le mat riel doit tre installe.
The pow er supp ly cord is used as the ma in disconn ect device. Ensu rethat the socket outlet is located o r installed n ear the equipment and iseasily accessible.
Le cordon d alimentation est utilis comm e interrup teur g n ral. Laprise de couran t doit tre situ e ou install e a proximite du m at riel ettre facile d acc s.
Caution: Neither the LCD AT Board nor the PCI LCD board is neededto ins tall a 5962 on the 7450 Workstation .
Caution: Use a groun ding strap wh en installing this feature.
8/6/2019 5962 User Manual
18/72
3-2 Chapter 3: Installation
PCI LCD CardThe PCI LCD card p rovides a PCI bus interface for th e 5952/ 5962 LCDDisplay Prod ucts. It is designed to p lug into a 32-bit 5V slot in astand ard PCI-equ ipped 7452. This card does not contain a 16550 UARTand associated sup p ort logic.
The VGA BIOS on this card occup ies mem ory locations C0000-C9FFF.
15376
Keyboard Header Connector(for optional internal harness)
Panel Select Switch(SW1) Power Harness Connector
VGA BIOS
PS/2 Keyboard Connector
LCD Connector
Setting the Panel Select Switch (SW1)
P1 P2 P3 Function
OFF OFF OFF Pan el 8 (Color DSTN) Default
OFF OFF ON Panel 7 (Mono STN)OFF ON OFF Panel 6 (Color TFT)OFF ON ON Panel 5 (Unused)ON OFF OFF Panel 4 (5-in. Mono)ON OFF ON Panel 3 (Unused)
ON ON OFF Panel 2 (Unused)ON ON ON Panel 1 (Unused)
8/6/2019 5962 User Manual
19/72
Chapter 3: Installation 3-3
Wedge LCD AT CardThe Wedge LCD AT Card p rovides an ISA bu s interface for the5952/ 5962 LCD Display Prod ucts. This board occup ies one of the ISAexpansion slots.
14340
RS/232 I/O Addressand IRQ Switch
ON
P1 P2 P3 P4 P5 P6
I/O Address Board IRQ
S W1
Board Adress Switch
ON
P1 P2 P3
Default Setting:All Off
S W2
F2, 1 A, 5 V
F1, 5 A, 12 V
LCD Connector
PS/2 KeyboardConnector
Optional RS-232 P ort
Setting the Board I/O Address (SW2)
The board ad d ress mu st be un ique for the 7452. If there are no conflictswith an y other installed boa rds th en factory settings can be used .
Positions 2 and 3 are used to select the Board I/ O Add ress. Position 1 isused to switch between Ring Indicator an d +5 V on p in 9 of the op tionalRS-232 p ort .
P1 P2 P3 Function
X OFF OFF Address 1A0h (Default)
X OFF ON Address 1B0h
8/6/2019 5962 User Manual
20/72
3-4 Chapter 3: Installation
P1 P2 P3 Function
X ON OFF Ad dress 268hX ON ON Address 288h
OFF X X +5 V on op tional RS-232 Port,pin 9 (Default)
ON X X Ring Ind icator on op tional RS-232 Port, p in 9
Setting the RS-232 I/O Address (SW1)
The first th ree positions of SW1 are used to set the RS-232 port ad d ress.
P1 P2 P3 Function
OFF OFF OFF Address 2F8h (COM2)
OFF OFF ON Address 3F8h (COM1)OFF ON OFF Address 338h
OFF ON ON Add ress 3E8h (COM3)
ON OFF OFF Add ress 238h
ON OFF ON Add ress 2E8h (COM4)
ON ON OFF Ad dress 2E0h (Default)
ON ON ON Disable RS-232 port
8/6/2019 5962 User Manual
21/72
Chapter 3: Installation 3-5
Setting the IRQ (SW1)
The last three positions of SW1 are used to set the IRQ for the board .
P4 P5 P6 Function
OFF OFF OFF IRQ3 (COM2)
OFF OFF ON IRQ4 (COM1)
OFF ON OFF IRQ5OFF ON ON IRQ9
ON OFF OFF IRQ10
ON OFF ON IRQ11 (Default)
ON ON OFF IRQ15
ON ON ON Disable RS-232 p ort
Optional RS-232 Break Out Port
If you want to u se the op tional RS-232 p ort on th e LCD AT Board , youmust install the RS-232 adapter.
Note: The op tional RS-232 port is only available w hen using theDynaKey. It s not av ailable with the Touch Screen.
1. Install the 10- p in header into the 10-p in connector (J7) on th e LCDAT Board.
2. Install the 9-pin D-Shell conn ector into an emp ty bu s slot insid e thePC or 7452.
Note: Becau se of the AT card moun ting bracket arrangement, u singthe adapter cable effectively tak es up an AT slot.
8/6/2019 5962 User Manual
22/72
3-6 Chapter 3: Installation
Setting DIP Switches (3xxx 686)
Note: DIP switch settings are not requ ired for a 5962 Wedge TouchScreen connected to a w orkstation equ ipp ed w ith a Series 4000motherboard . The DIP switches for a Series 4000-equipp ed workstationare located on th e PCI LCD card.
1. Set the p rocessor sp eed according to the following tables:
Processor Type SW1-1 SW1-2 SW1-3 SW1-4 SW1-5
Class 35xx 686/ 233 Off On Off Off Off Class 35xx 686/ 333 Off On Off On OnClass 35xx 686/ 400 Off On On Off Off Class 3xxx 686/ 100 Off On Off Off N/ AClass 3xxx 686/ 166 Off On On On N/ A
Class 3xxx 686/ 233 Off On Off Off N/ AClass 2xxx 686/ 100 Off On Off N/ A N/ A486-DX4/ 100 On N/ A N/ A N/ A N/ A
2. Set the p rocessor voltage control ju mp er accord ing to the followingtable:
Processor Type Jumper SW3-1 SW3-1 SW3-1
Class 35xx 686/ 233 N/ A Off Off Off Class 35xx 686/ 333 N/ A On Off Off Class 35xx 686/ 400 N/ A On Off Off
8/6/2019 5962 User Manual
23/72
Chapter 3: Installation 3-7
3. Strap the 35xx 686 Processor Board accord ing to the following table:
Display Type SW2-1 SW2-2 SW2-3
Color (passive)(F305, F405, F407)
OFF OFF OFF
Mono (passive)(F306, F406, F408)
OFF OFF ON
Active Matrix or TFTDisplay (F310, F409, F410)
OFF ON OFF
5" LCD ON OFF OFF
9" Mono LCD OFF OFF ONNo Disp lay or CRT OFF ON OFF
Note: The 35xx 686 Processor Board has an interna l connection to
COM2: on th e moth erboard . When a Mod el 5962 Tou ch Screen ispresent, COM2: cannot h ave any other d evice conn ected to it.
4. Replace the Base Unit Top .
8/6/2019 5962 User Manual
24/72
3-8 Chapter 3: Installation
Installing the 59621. Pry open the cable cover with a screw d river and remove the cover.
12263
2. Turn the unit over, remove the keys from the keylock and lay it on aflat su rface so the MSR hangs off the edg e.
12375
8/6/2019 5962 User Manual
25/72
Chapter 3: Installation 3-9
3. Route the LCD Display and other cables through the hole in theTou ch Mod ule Base.
Cables Outthe Front
Cable Hold-Down
Cables Outthe Back
If you have an additional cable,it should be pinched between thetwo plastic studs to act as a strain relief.
NOTE:
14102a
Cable Routing in the Touch Module Base
8/6/2019 5962 User Manual
26/72
3-10 Chapter 3: Installation
4. Connect the cables to the proper connectors.
RS-232 Scanner
LCD Display Connector
PC Keyboard Connector
Cable Guide
14101
Cable Connectors
5. Install the cable cover.
14103
8/6/2019 5962 User Manual
27/72
Chapter 3: Installation 3-11
Wall Mounting the 5962The Touch Screen assembly can be tilted to facilitate wa ll mou nting.
1. Remove the Filler Plate from the base.
Filler Plate
Remove (2) Screws12262
2. Mount the bracket on the w all or a vertical structure that canadequ ately sup port the unit.
12368
3 12 Ch t 3 I t ll ti
8/6/2019 5962 User Manual
28/72
3-12 Chapter 3: Installation
3. Hang the unit on the Mounting Bracket shoulder screws.
12367
Shoulder Screws
Chapter 3: Installation 3 13
8/6/2019 5962 User Manual
29/72
Chapter 3: Installation 3-13
Installing an Integrated 2x20 Customer Display1. Remove the Custom er Display Cover (2 screws).
14402
5972 Display (2x20)
Post Mount Cover
Mounting Plate
Customer Display Cover
BaseS
3-14 Chapter 3: Installation
8/6/2019 5962 User Manual
30/72
3 14 Chapter 3: Installation
2. Routing the serial cable.
The serial cable can be routed through the m ouse hole or throughthe oval-shaped hole in the base of the touch m oun t.
3. Routing the p arallel cable.
The p arallel cable mu st be routed throu gh the m ouse hole and upthrou gh the p ost. The D-shell connector is routed dow n th roughthe 2.75 in. x 2 in oval-shap ed open ing to on e side of the swivel of the Remote Base mou nt.
4. Moun t the post to the Base and the Mounting Plate with the 5screws provided .
5. Conn ect the serial or p arallel cable conn ector to the h ostwor kstation. Route the cable throu gh the chan nel in the base of theRemote Base.
6. Plug the pow er cable into the pow er source.7. Turn on the pow er source.
Chapter 3: Installation 3-15
8/6/2019 5962 User Manual
31/72
C apte 3: sta at o 3 5
Connecting to a WorkstationNote: Be sure that the w orkstation is pow ered off before connectingany cables to it.
1. Connect the adap ter cable from the adap ter board (LCD or PCI) tothe keyboard connector on the rear panel of the workstation. (The5-PIN connector connects to the adap ter board . The 6-PIN
connector connects to the workstation keyboard connector.)2. Connect the LCD cable as shown.
To Hard DrivePower Connector
PCI LCD
Board
To PC KeyboardConnector To PC
RS-232 Port To PC KeyboardConnector
LCD AT
Board
PC KeyboardAdapter Cable
15810b
3-16 Chapter 3: Installation
8/6/2019 5962 User Manual
32/72
p
Powering UpThis section describes how to pow er up th e workstation and the initialcheckou t procedu res after all hard ware has been installed .
Note: No u nit setup is required at installation un less the configurationmust be chan ged from factory d efau lts. The Wedge Support Disk (LPING370-0701-0000) permits configuration of the operational parameters inthe Wedge.
Power Up1. Plug the AC Power Cord into an AC p ower sour ce.
2. Turn the keylock to the Ex position.
3. Power on the workstation.
Powering Up the Workstation after Replacing the PCI LCDBoard
If you are insta lling a 5962 after rep lacing the PCI LCD board with aservice board , you m ay need to change the switch settings to set thepan el display on the new board. Otherwise, you may encounter p oord isplay resu lts or a blank screen. Refer to th e table called Setting thePanel Select Switch (SW1) earlier in th is chap ter.
Powering Up the Workstation after Replacing the LCD AT Board
If you are installing a 5962 after replacing the LCD AT board with aservice board , you m ay need to up date the VGA BIOS for the newboard . Otherwise, you m ay encoun ter poor d isp lay resu lts. You alsoneed to up d ate switch settings if you are using the LCD AT Board .
Powering Up the Workstation after Replacing the Series 35xxMotherboard
If you are insta lling a 5962 after rep lacing the Series 35xx Moth erboard ,you may need to chang e the switch settings to set the p anel display on
the new board. Otherwise, you m ay encounter poor d isplay results.
Chapter 3: Installation 3-17
8/6/2019 5962 User Manual
33/72
Screen Saving FeatureThe display has a time-out function that causes the display to go blank after several minu tes of inactivity.
The screen saving featu re is controlled by N CR p latform softwareintegrated into the 5962 d rivers.
Note: If you r screen saver is active and the keylock is in the Lposition, you m ay need to pu t the keylock into another p osition to
un blank the LCD.
When a key is pressed to return the d isplay from screen saver mod e,the resu lting keystroke is passed to the app lication by d efault.
To discard the keystroke, use the /D op tion with th e CONSOLEW. DOSdriver. Ad d itional inform ation on this driver is included in the 7450Software Users Guide , BST0-2122-21 for more in form ation .
See Chapter 4, Program ming, for inform ation on how to p rogram th eVGA controller for p roper p anel OFF/ ON sequencing.
3-18 Chapter 3: Installation
8/6/2019 5962 User Manual
34/72
8/6/2019 5962 User Manual
35/72
Chapter 4: Programming
Software Drivers and Utilities
MicroTouch Touchscreen Drivers and UtilitiesA Wedg e with Touch Screen op tion requ ires the MicroTouch TouchScreen Drivers and Utilities. The LPIN includes Touch Screen Drivers,Utilities and Manuals.
The NCR 74xx Base System an d Client 3 rd Party Drivers LPIN D370-1111-0100 includes the software from G370-0525-0000, G370-1289-0000,and G370-0835-0000. This LPIN includ es configuration and calibrat ionu tilities for the MicroTouch tou ch screen for DOS, Win 3.11, Win 95,Win 98, and Win NT.
Note: Do n ot use th e GetSet3 utility w ith the NCR 5962.
For Wind ows 95 and N T environm ents use the Windows StartMenu at : START/PROGRAMS/MICROTOUCH/TOUCHWARE CONTROL
PANEL
For more informa tion on the Touch Screen controller and firmw arecomm ands , contact MicroTou ch Systems, Inc. at 300 Griffin Brook Park Drive, M ethu en, MA 01844 or teleph one: (508) 659-9000.
Note: When ever an app lication or d river turns the backlight off or on,it shou ld a lso reset the Touch Controller (send a RESET command ).This ensu res that the noise generated by the sideligh t is nu lled an ddoesn t affect touch accuracy.
4-2 Chapter 4: Programming
8/6/2019 5962 User Manual
36/72
Device InterfacesThis section p rovides inform ation on the d evice interfaces.
Wedge Controller InterfaceThe Wedge consists of a microcontroller an d associated circuitry th atsu pp orts a th ree-track Magnet ic Stripe Reader (MSR), an RS-232
device, and keylock. The Wedg e merges the data into the keyboarddata stream.
The data ar rives at the retail workstation or PC as if someone hadentered it directly throu gh a keyboard . An app lication can u se sp ecialstart and end contro l characters to determ ine that the inform ationactually cam e from the Wedge instead of the external keyboard .
The Wedge a lso controls the operation of the bu ilt-in speaker (not th ePC speaker) and the status LEDs.
For more informa tion on the Wed ge, refer to the NCR W edge SoftwareUser s Guide , BD20-1368-A. Contact your N CR sales representative toorder th is book.
Touch Screen InterfaceThe Touch Screen m odu le connects to th e 7453 retail workstation or PCthrou gh th e external conn ector on the N CR Wedge LCD AT board or aPCI LCD board .
The Touch Screen controller stores its configu ration in formation in anon-volat ile RAM (NOVRAM). Therefore, this inform ation is not lostwh en the board loses power.
Chapter 4: Programming 4-3
8/6/2019 5962 User Manual
37/72
The Touch Screen firmw are d efaults to the following comm unicationsparameters: 9600 baud No pa rity 7 data bits 2 stop bit Autobau d d isabled
Note: These p aram eters may be changed by the MicroTouch drivers.To set them, use the MicroTouch M icroCal program.
For more informa tion on the Touch Screen controller and firmw arecomm ands , contact MicroTouch Systems, Inc. at 300 Griffin Brook Park Drive, Methuen, MA 01844 or telephone: (508) 659-9000.
Analog MSR InterfaceThe analog MSR interface sends da ta to the workstation or PC throu ghthe Wedg e controller. The data is amp lified an d th en formatted by thewedge.
RS-232 Interface
The RS-232 interface allows connection of RS-232 devices such as adecoded laser scann er. The conn ector p rovides th e RS-232comm unications lines and +5V and GROUND. Most scanners d o notrequire an external p ower sup ply. The Wedge read s the scanner dataand places it in the PC keyboard da ta stream.
PS/2 Keyboard InterfaceA PS/ 2-style keyboard connector permits alph anu meric entry and non -touch app lications to be used throug h a stand ard PC keyboard. Youcann ot connect and use a Wed ge Keyboard in th is p ort.
Note: The keylock is not available as a pass-through interface. Youcan only access it th rough the Wedge controller.
4-4 Chapter 4: Programming
8/6/2019 5962 User Manual
38/72
Panel OFF/ON SequenceThe instructions for p rogramm ing the LCD pan el OFF/ ON sequ enceare d ifferent for the LCD AT board and the PCI LCD board . Be sure touse the p roper instructions.
Before turn ing th e Panel Off, turn off the v ideo u sing SequencerRegister 1 bit 5 (SR01[S]) in the sam e manner as IBM recommends forthe stan dard VGA. To m ake Video Off more effective, some ad d itional
delay shou ld be included before Panel Off.
By tu rnin g the Video Off via SR01[5], the Sequ encer is no longerrefreshing the screen. This gives the Sequ encer enou gh ban dwid th towork with the Panel Off logic to do an orderly shutd own of the videooutput.
PCI LCD Board (65550 Chips)Panel Off Sequence:
Save Sequencer Register IndexTur n Video Off (SR01[5]=1)Restore SR Ind exDelay 15mS
Turn Panel Off (FR05[3]=1)
Panel On Sequence: Turn Panel On (FR05[3]=0)Save SR IndexTurn Video On (SR01[5]=0Restore SR Ind ex
Chapter 4: Programming 4-5
8/6/2019 5962 User Manual
39/72
LCD AT Board (65535 Chips)
Panel Off Sequence: Save Sequencer Register IndexTur n Video Off (SR01[5]=1)Restore SR Ind exDelay 15mSTurn Panel Off (XR52[3]=1)
Panel On Sequence: Turn Panel On (XR52[3]=0)Save SR IndexTurn Video On (SR01[5]Restore SR Ind ex
These are brief sequence examples. Imp lementation is up to the u ser. If there are any questions regard ing these sequ ences, p lease contact
NCR Techn ical Support, or
Chips and Technologies, Inc.2950 Zanker RoadSan Jose, CA 95134(408) 434-0600.
8/6/2019 5962 User Manual
40/72
8/6/2019 5962 User Manual
41/72
Chapter 5: Service and Repair
Safety RequirementsCarefully follow these safety requ irements before servicing the TouchScreen.
Warning: The Touch Screen LCD contains hazardous vo ltages andshould only serviced by qualified service personnel.
Warning: Before servicing the equ ipment plug y our safety strapinto a prope r grounding outlet. Failure to do so could damage the
equipment.Caution: Before servicing the Touch Screen, disconnect the AC powercord from the retail workstation or PC to wh ich th e Touch Screen isconnected. Also disconn ect the cables from the PC or w orkstation tothe Touch Screen.
Caution: To p rotect the internal circu itry from d amage, unp lug the
AC power cord and then mom entarily press the power switch ON todrain th e power sup ply capacitance.
Caution: The p ower sup ply cord is used as the m ain disconn ectdevice. Ensure that the socket ou tlet is located / installed n ear theequ ipm ent an d is easily accessible.
Attention : Le cordon d alimentation est utilis comme interrupteurgn ral. La prise de couran t doit tre situ e ou install e a p roximite dumat riel et tre facile d acc s.
8/6/2019 5962 User Manual
42/72
Chapter 5: Service and Repair 5-3
8/6/2019 5962 User Manual
43/72
Symptom Probable Cause Solution
Workstation notconfigu red prop erly
Set speaker volume to m aximu m in the7450 Configuration Setup
MSR not work ing MSR ca rd not or ien tedproperly
Ensure that magnetic stripe on card isup when swiped.
MSR ha rness loose orbroken
Ensure that M SR harness is securelyfastened to the Touch Screen controlboard, and that none of the w ires havepu lled loose from the connector.
Wedg e Controllerconfigured incorrectly
Configure MSR operation using Wed geu tility (See NCR Wedge Softw are User sGu ide, BD20-1368-A)
Scanner not working Scanner not powered Check fuse in Touch Screen Module
Unsupp orted scannerconnected to u nit Ensure that the scanner is a decoded (RS-232) model
Wedg e Controllerconfigured incorrectly
Configure scanner operation usingWedge u tility (See NCR Wedge SoftwareUser s Guide, BD20-1368-A)
LCD Dim/ Contrast
too Ligh t or Dark
Unit is cold Wait 15 minu tes for unit to reach
operating temp erature before measu ringbrightn ess or contrast. Do not expose theun it to operating temp eratures below 5 C.
Contrast set incorrectly If your un it has a Passive Matrix LCD,ad just contra st using the control knob.Usually a setting n ear the m idd le
prov ides the best display.
Unit in direct sunlight For best display quality, keep the unit outof direct sunlight or other br ight ligh tsources.
5-4 Chapter 5: Service and Repair
8/6/2019 5962 User Manual
44/72
Symptom Probable Cause Solution
Wron g VGA BIOS Flash th e w orkstation or PC w ith th ecorrect VGA BIOS ( VGABIOSC.B2X forthe p assive m atrix mod el, andVGABIOSA.B2X for the active m atrixmodel)
Wrong VGA BIOS SwitchSetting
If using the PCI LCD board , set the PanelSelect switch to m atch the LCD panel
(pan el 8 for p assive matr ix, pan el 6 foractive matrix).
Lines in LCD Display Intern al LCD harn essloose
Re-seat the LCD harn ess at the TouchScreen control board an d LCD end s.
External LCD cable isloose
Ensure that the LCD cable is securelyfastened to the LCD board , or Y-cable.
Bent p in in external LCDcable
Check both ends of the LCD cable forben t p ins. Fix or rep lace cable.
TFT Adap ter Board loose If active matrix, ensure that the TFTAd ap ter Board is prop erly conn ectedbetween the Touch Screen control boardand LCD harn ess. This board shou ld
NOT be u sed for p assive m atrix un its.Wron g VGA BIOS Flash th e w orkstation or PC w ith th e
correct VGA BIOS ( VGABIOSC.B2X forthe p assive m atrix mod el, andVGABIOSA.B2X for the active m atrixmodel)
Wrong VGA BIOS SwitchSetting
If using the PCI LCD board , set the PanelSelect switch to m atch the LCD panel(pan el 8 for p assive matr ix, pan el 6 foractive matrix).
Chapter 5: Service and Repair 5-5
8/6/2019 5962 User Manual
45/72
Symptom Probable Cause Solution
No d isplay (GreenLED ON )
Contrast control setincorrectly
If p assive matrix, tu rn contra st controlkn ob to ad just contrast. Usua lly a settingnear the m idd le provid es the best displayquality.
Wron g VGA BIO S If u sin g th e PCI LCD Board , set th e Pan elSelect switch to m atch the LCD panel(pan el 8 for p assive matr ix, pan el 6 for
active matrix).Wrong BIOS SwitchSetting
If using th e PCI LCD Board, set the PanelSelect switch to m atch the LCD panel(pan el 8 for p assive matr ix, pan el 6 foractive matrix).
Interna l LCD harn ess
loose
Re-seat the LCD harn ess at the Touch
Screen control board an d LCD end s.LCD Adap ter Board loose If active m atrix, ensure that th e LCD
Adap ter board is prop erly conn ectedbetween the Touch Screen control boardand LCD harn ess. This board shou ldNOT be u sed for p assive m atrix un its.
Interna l backlight harnessloose Ensure that the backlight harness issecurely fastened to the Touch Screencontrol board.
No d isplay (OrangeLED ON )
Unit in standby modescreen blank)
Return un it from stand by as requ ired byap p lication. Ensu re keylock not in Lposition.
LCD-AT board addressswitch set wrong
Set LCD-AT SW2 for boa rd ad dress to1A0
No d isplay (LEDOFF)
7450: Unit in standby mode (screen blank)
Return un it from stand by as requ ired byap p lication. Ensu re keylock not in Lposition.
5-6 Chapter 5: Service and Repair
8/6/2019 5962 User Manual
46/72
Symptom Probable Cause Solution
7450: Workstationstrapped for 2x20 op eratordisplay.
Set d ip sw itches on 7450 processor boardfor non-2x20 an d +12V ON
Cables loose Ensure all cables are securely connected.
Blown fuse - LCD-AT card Check +12V fuse on LCD-AT card
Blown fuse - PCI LCD
card
Check +12V fuse on PCI LCD card
Power Harn ess loose ornot conn ected
If using PCI LCD card, ensu re that th ehard disk pow er harness is properlyconnected to the PCI LCD card.
Touch Screen n otworking
LCD-AT board s RS-232port n ot set correctly
Set SW1 on LCD-AT card for the p rop erCOM ad dress and IRQ. Ensure tha t the
settings d o not conflict w ith otherresources.
PCI LCD board s RS-232port n ot set correctly
If using th e PCI LCD card, set the COMad dress and IRQ on the motherboard orRS-232 expansion card p rop erly. Ensu rethat the settings d o not conflict w ithother resources.
7450: COM2 RS-232 p ortnot set correctly
Ensur e COM2 is enabled on the 7450.
Class 3500: Another d eviceis connected to COM2: onthe motherboard
Remove th e external d evice. The Class35xx 686 motherboa rd has an internalconnection to the 5962 Wedge TouchScreen.
Incorrect RS-232 settingsin the Tou ch ScreenController or ap p lication
The d efau lt setting for the Touch Screenis 9600 N 7 2. Ensu re that the app licationand Touch Screen settings m atch. TheTouch Screen can be reconfigured usingthe MicroTouch MICROCAL.EXE program.
Chapter 5: Service and Repair 5-7
8/6/2019 5962 User Manual
47/72
Symptom Probable Cause Solution
Touch Screen sensorharness loose
Ensur e that the Touch Screen sensorharness is secu rely fastened to the 5962control board.
External h arness loose ornot connected.
If using PCI LCD card, make sure thatthe Y-cable is properly connected. Thiscable is different th an that used by theLCD-AT card .
Bent p in in external LCDcable
Check both ends of the LCD cable forben t p ins. Fix or rep lace cable.
Touch Screen n otaccurate
Touch Screen n otcalibrated properly.
Load th e MICROCAL.EXE program andtest the calibration using th e draw u tility. If calibration is incorrect,recalibrate u sing the 2-point calibration
option in MICROCAL.EXE .Touch Screen n otfound byMICROCAL.EXE
Touch Screen RS-232 portset to add ress other thanCOM1 or COM2.
MICROCAL.EXE program only searchesCOM1 and COM 2 by d efau lt. Typ eMICROCAL.EXE /? for information onhow to search other COM port ad dresses.
NOVRAM error inMICROCAL.EXE
First time p ower u p of a
new board.
The first time a new board is p owered
up , this message is displayed w henrunning MICROCAL.EXE . This does notind icate a failure, but rath er that the on-board non -volatile mem ory is blank. Thecontroller initializes the NOVRAM on thefirst p ower u p. This message should n otbe displayed on subsequent pow er u ps.
5-8 Chapter 5: Service and Repair
8/6/2019 5962 User Manual
48/72
Servicing the Touch Screen ModuleThis section p rovides d etailed instru ctions on h ow to comp letelyd isassemble the N CR 5962 Tou ch Screen LCD.
Opening the Cabinet1. Pry op en the cable cover w ith a screw d river and remove the cover.
12263
2. Disconnect the interface cable(s) from the Touch Module.
14101a
RS-232 Scanner
LCD Display Connector
PC Keyboard Connector
Cable Guide
Chapter 5: Service and Repair 5-9
8/6/2019 5962 User Manual
49/72
3. Remove the Keylock key. Turn th e Tou ch Module over and lay iton a flat sur face so the MSR hangs off the ed ge and pu ll off the
Contrast Control knob.
12375
4. Tilt the un it up to fit the Phillips-head screwdriver and loosen thecabinet screw.
14451
5-10 Chapter 5: Service and Repair
8/6/2019 5962 User Manual
50/72
5. Remove the Base Cabinet Assembly by p ivoting the un it backw ard sto avo id break ing tabs. Leave the screw in the cabinet for easier re-
assembly.
3
2
1
14496
Chapter 5: Service and Repair 5-11
8/6/2019 5962 User Manual
51/72
Internal Components
LCD HarnessConnector
BacklightConnector
SpeakerConnector
Touch SensorConnector
MSRConnector
KeylockConnector
14493
Fuse 1 AMP125V External LCD
Connector
ScannerConnector
KeyboardConnector
Speaker
Keylock
StandbySwitch
Contrast ControlKnob
Caution: For continu ed p rotection against r isk of fire, replace onlywith the same type and ratings of fuse.
Attention : Pour p r venir et vous prot ger contre un risqu e de feu ,remplacer la fusible avec une au tre fusible d e m me typ e, seulement.
5-12 Chapter 5: Service and Repair
8/6/2019 5962 User Manual
52/72
Replacing Primary PartsThe replacement of the following p rimary p arts are covered in thissection.
Touch Con trol Board
Speaker
MSR
Keylock
Touch Glass
LCD
Chapter 5: Service and Repair 5-13
Replacing the Touch Control Board
8/6/2019 5962 User Manual
53/72
Replacing the Touch Control Board
1. Disconn ect the following h arn esses: Touch Sensor, MSR, Keylock,LCD, Speaker, and Backlight.
LCD HarnessConnector
BacklightConnector
SpeakerConnector
Touch SensorConnector
MSR Connector
Keylock Connector
14457
5-14 Chapter 5: Service and Repair
2 Remove the (3) screws that secure th e contro l board to the bracket
8/6/2019 5962 User Manual
54/72
2. Remove the (3) screws that secure th e contro l board to the bracketas shown.
14474
(3) Screws
Standoffs
Chapter 5: Service and Repair 5-15
3. Carefully p ry the board from the (2) metal stand -offs and remove
8/6/2019 5962 User Manual
55/72
3. Carefully p ry the board from the (2) metal stand offs and removethe board.
14454
Replacing the Speaker
1. Disconn ect the sp eaker cable
2. Unscrew the speaker from the bracket.
14456
5-16 Chapter 5: Service and Repair
Note: The replacement speaker is generic in that it has a groun d w ire
8/6/2019 5962 User Manual
56/72
p p g g(white) attached to the speaker assembly. Since the speaker is m oun ted
d irectly to the fram e of the Touch Assembly, the groun d wire is notnecessary.
3. Cut off the speaker groun d wire.
Replacing the MSR
1. Carefully disconnect the MSR Harn ess from the PC Board .
MSR Connector
14472
Chapter 5: Service and Repair 5-17
2. Remove th e (2) screws hold ing th e MSR into p lace.
8/6/2019 5962 User Manual
57/72
(2) Screws
14197
3. Replace th e MSR.
5-18 Chapter 5: Service and Repair
Removing the Keylock
8/6/2019 5962 User Manual
58/72
1. Disconn ect the cable from the PC board .
2. Use need le nose p liers to remov e the metal retaining clip fromkeylock.
14455
3. Squ eeze the plastic retainers and push th e keylock out the front of
the un it.4. Reinsert the keylock, lining u p th e narrow and wide tabs and snap
into p lace.
5. Reinsta ll the meta l retaining clip .
6. Carefully bend the w ires over so they lay flat.
7. Reinsta ll the h arness.
Chapter 5: Service and Repair 5-19
Removing the Touch Glass
8/6/2019 5962 User Manual
59/72
1. Disconn ect the Keylock an d Touch Sensor cables from the p rintedcircuit board .
2. Remove th e (4) screws tha t secu re the LCD Assembly to th e fron tcover.
14475
(4) Screws
3. Remove the assembly.
5-20 Chapter 5: Service and Repair
4. Remove th e glass.
8/6/2019 5962 User Manual
60/72
14453
14453
Note: Clean any lint from th e glass and LCD before reinstalling.
5. Seat the g lass firm ly between th e guid es.
Chapter 5: Service and Repair 5-21
Removing the LCD
8/6/2019 5962 User Manual
61/72
Removing the LCD
1. Disconn ect the Keylock an d Touch Sensor cables from the p rintedcircuit board .
2. Remove th e (4) screws tha t secu re the LCD assembly to the frontcover.
14475
(4) Screws
3. Remove the assembly from the front bezel.
4. Disconn ect the backlight ad ap ter cable.
5. Disconn ect the LCD cable from the LCD (remove from the LCDend).
5-22 Chapter 5: Service and Repair
6. Remove the (2) hex nu ts that secure the Touch Con trol BoardBracket to the Touch Assem bly
8/6/2019 5962 User Manual
62/72
Bracket to the Touch Assem bly.
14294Hex Nuts
7. Remove the Board Bracket.
8. Remove th e (4) p lastic hex nu ts on th e Touch Assembly.
Remove Plastic Hex Nuts (4)
14295
9. Insert the new LCD.
Chapter 5: Service and Repair 5-23
Reassembling the Touch Screen
8/6/2019 5962 User Manual
63/72
The Touch Screen Mod u le can be re-assem bled using the reverse ord erof the p revious p rocedu res. In add ition, be aw are of the followingsuggestions:
Before closing the cabinet check the screen an d sensor g lass tomake sure there are no fingerp rints or lint p articles.
Make su re the cables (especially the Tou ch cable) are rou tedprop erly before closing the cabinet.
5-24 Chapter 5: Service and Repair
Spare Parts List
8/6/2019 5962 User Manual
64/72
Nu mbered items show n in this illustration correspond to the parts liston th e next pag e.
5
1
4
3
1 0
7
6
11
1 3
1 3
1 4
1 5
1 2
2
89
17
18
16
14480
The following is a listing of spa re parts for th e NCR 5962 Wedge TouchScreen.
Chapter 5: Service and Repair 5-25
Item Part Part Number
1 B l A bl (A ) 497 0405494
8/6/2019 5962 User Manual
65/72
1 Bezel Assembly (Assy.) 497-0405494
2 PCB Bracket 497-0405126
3 LCD Bracket 497-00100247
4a LCD Passive Mat rix 10.5 497-0406373
4b LCD Active Mat rix 10.5 497-0407551
5 Assy. - 10.5 Touch Glass 497-0010664
6 Speaker 250-0046042
7 Harness-Color LCD 497-0405341
8 Knob - Touch Screen 497-0404996
9a Harness - Color LCD Inver ter (Passive Matrix) 497-0405259
9b Harness - Color LCD Inver ter (Act ive Matr ix) 497-040662810 Control Board 497-0406460
11 Keylock 497-0405163
Gasket 497-0010180
Mou nt-MSR 497-0405098
Cover-Cable 497-0403221
Cover-No MSR 497-0403630
Card - LCD AT, Color 497-0405180
Card - PCI LCD 497-0408765
Actuator-Switch 497-0405340
Assy.-In teg. Mount 497-0405750
Pad - Compression 497-0407161
TFT LCD Ad ap ter Board 497-0406565
Assy.-Touch Screen Support 497-0405832
5-26 Chapter 5: Service and Repair
Item Part Part Number
MSR 3 Track 497 0405705
8/6/2019 5962 User Manual
66/72
MSR-3 Track 497-0405705
Wed ge Keyboard Adap ter Cable 497-0405420
Wed ge Keyboard Y-Cable 497-0407490
Harness - PCI LCD HD PWR 497-0407803
Wedge Disp lay Cable(1 meter)
497-0405760
Wedge Disp lay Cable(2 meter)
497-0405761
Wedge Disp lay Cable(4 meter)
497-0405762
7450 Wedge Y-Cable 497-0405654
Chapter 5: Service and Repair 5-27
Connectors
8/6/2019 5962 User Manual
67/72
This section d escribes the Touch Screen LCD connectors.
External Keyboard ConnectorThe external keyboard connector is a PS/ 2-style, 6-pin, mini-DINconnector. The table below lists the function of each p in.
Pin Symbol Description1 DATA Keyboard Data
2 N/ C Unused
3 GROUND Ground
4 +5V 5V Power
5 CLOCK Keyboard Clock
6 N/ C Unused
External RS-232 Scanner ConnectorThe external RS-232 scanner connector is an 8-p in m odu lar connector.The table below lists the fun ction of each p in.
Pin Symbol Description
1 N/ C Unused
2 N/ C Unused
3 GROUND Ground
4 TXD Data to Scanner
5 RXD Data from Scanner
6 +5V 5V Power
7 CTS Clear To Send (from Scanner)
8 RTS Request to Send (to Scanner)
5-28 Chapter 5: Service and Repair
Touch Screen Cleaning Procedures
8/6/2019 5962 User Manual
68/72
1. Spray an amm onia-based glass cleaner on a soft cloth and gentlywip e the touch screen clean.
Warning: Do no t use any other types of cleaners such as vinegar,solv ents, or degreasers. These can damage the screen .
2. Wipe th e screen and edges dry.
3. Allow th e glass and screen edges to comp letely dry before usingthe unit.
Index-1
Index
8/6/2019 5962 User Manual
69/72
C Cables
connecting to a PC, 3-15using a w edge Y-cable, 1-1
ConnectorsRS-232, 4-3
K keylock, 1-3Keylock, 1-1
location, 1-3positions, 1-3
L LCD AT board, 1-2
operating ran ge, 2-1operating ran ge, 2-1storage r ange, 2-1transit range, 2-1
LED
status and cond itions, 1-3
M Magnetic Stripe Read er (MSR), 1-1
ana log interface, 4-3
P PC Keyboard, 1-1
external connector, 1-3
S Screen Saving
u nblanking the LCD, 3-17Speaker, 1-1
removing ground wire, 5-17
T Touch Screen Mod u le
servicing, 5-9Troubleshooting Table, 5-2
V VGA BIOS
updating, 3-16
Index-2
8/6/2019 5962 User Manual
70/72
8/6/2019 5962 User Manual
71/72
8/6/2019 5962 User Manual
72/72
BD 20-1371-B Sep . 2000Printed on r ecycled p aper