8/11/2019 725C Instruction Manual Rev 0.1
1/134
Series 725C Instruction Manual
Page 1 of 134
Warning The 725C System described herein operates on a logic voltage of 24VDC andas standard 24VDC is used for the field contact supply voltage.
Internal or External power supplies using higher voltage AC/DC primarysources and optional high voltage field contact voltages may be present.If this is the case please ensure the necessary precautions are taken.
REV DATED DESCRIPTION AUTHOR APPROVED0 31-08-06 First Issue P.Cartmell T. McLeman
7 2
5 C S e
r i e s
A l ar m A nn
un
c i a t o
r
8/11/2019 725C Instruction Manual Rev 0.1
2/134
Series 725C Instruction Manual
Page 2 of 134
S ECTION 1 - INTRODUCTION .......... ........... ............. ........... ........... ......... 7 General.................................................................................................................... 7 Programmable Features............. ........ ........ ......... ........ ........ ........ ......... ........ ........ ..... 7 Glossary of Terms .................................................................................................... 8
Annunciator Model Code Definition.... .... .... .... .... .... .... .... ... .... .... ... .... .... ... .... .... ... .... .... 9 Product Overview ................................................................................................... 11 System Front View.................................................................................................. 11 Window Illumination................................................................................................ 13 Window Colours ..................................................................................................... 13
Adding or Changing Film Legends... .... ... .... .... ... .... .... .... ... .... .... ... .... .... ... .... .... ... .... .. 14 Filter & Bezel Spare Parts Numbers...... ........ ........ ........ ........ ......... ........ ........ ........ .. 14 Laser Printed Legends ............................................................................................ 14 Window Numbering System ........ ......... ........ ........ ........ ........ ......... ........ ........ ........ .. 15 Remote Pushbutton Module ........ ......... ........ ........ ........ ........ ......... ........ ........ ........ .. 18
S ECTION 2 CELL TYPES .......... ........... ............. ........... ........... ........... 19 A Cell Detail .... .... .... .... .... .... .... ... .... .... ... .... .... ... .... .... .... ... .... .... ... .... .... ... .... .... ... .... .. 19
A Cell - Differential Input Version .... .... .... .... .... ... .... .... .... ... .... .... ... .... .... ... .... .... ... .... .. 20
AR Cell Detail .... ... .... .... ... .... .... ... .... .... ... .... .... ... .... .... .... ... .... .... ... .... .... ... .... .... ... .... .. 21 AR Cell - Differential Input Version..... .... .... .... .... .... .... .... ... .... .... ... .... .... ... .... .... ... .... .. 22 AP Cell Detail .... ... .... .... ... .... .... ... .... .... ... .... .... ... .... .... .... ... .... .... ... .... .... ... .... .... ... .... .. 23 APR Cell Detail... .... .... .... .... .... .... .... .... ... .... .... ... .... .... .... ... .... .... ... .... .... ... .... .... ... .... .. 24 AS Cell Detail .... ... .... .... ... .... .... ... .... .... ... .... .... ... .... .... .... ... .... .... ... .... .... ... .... .... ... .... .. 25 AS Cell - Differential Input Version.. .... .... .... .... ... .... .... .... ... .... .... ... .... .... ... .... .... ... .... .. 26 S Cell Detail ........................................................................................................... 27 SS Cell Detail ......................................................................................................... 28 WR Cell Detail........................................................................................................ 29 WRS Cell Detail...................................................................................................... 30 WRR Cell Detail...................................................................................................... 31 Optional WR Cell Detail............... ......... ........ ........ ........ ........ ......... ........ ........ ........ .. 32
S ECTION 3 LOGIC SUPPLY & FUSING......... .......... ........... ............. ... 34 Externally Powered Systems ......... ........ ........ ........ ......... ........ ........ ........ ......... ........ 34 SI/O Card Versions................................................................................................. 34 Systems using Internal Power Cards....... ......... ........ ........ ........ ........ ......... ........ ....... 35 SI/O Card Versions................................................................................................. 35
S ECTION 4 - SIGNAL SUPPLY VOLTAGE SETTING.......... ........... ....... 36 24V or 125V AC/DC Signal Inputs......... ........ ........ ........ ........ ......... ........ ........ ........ .. 36 48V or 250V AC/DC Signal Inputs......... ........ ........ ........ ........ ......... ........ ........ ........ .. 37 24VAC/DC Signal Inputs ......................................................................................... 38 Optional 125VAC/DC Signal Inputs.... ........ ........ ........ ......... ........ ........ ........ ......... .... 39 Optional 48VAC/DC Signal Inputs ......... ........ ........ ........ ........ ......... ........ ........ ........ .. 40 48VAC/DC Signal Supply. ......... ........ ........ ........ ........ ......... ........ ........ ........ ......... .... 40 Optional 250VAC/DC Signal Inputs.... ........ ........ ........ ......... ........ ........ ........ ......... .... 41 250VAC/DC Signal Supply ........ ........ ........ ........ ........ ......... ........ ........ ........ ......... .... 41 Optional Differential Input Version........... ......... ........ ........ ........ ........ ......... ........ ....... 42
S ECTION 5 COMMON RELAYS......... ........... ........... ............. ........... ... 43 Group Relay........................................................................................................... 44 Input Follower Relay ............................................................................................... 44
Alarm Follower Relay.. .... .... .... .... .... .... ... .... .... ... .... .... .... ... .... .... ... .... .... ... .... .... ... .... .. 44 Audible Follower Relay ....... .... .... .... .... ... .... .... ... .... .... .... ... .... .... ... .... .... ... .... .... ... .... .. 44 Pushbutton Follower Relay..... ........ ........ ......... ........ ........ ........ ........ ......... ........ ....... 44 Diagnostic / Watchdog Relay...... ........ ........ ......... ........ ........ ........ ......... ........ ........ ... 44 Field Contact Monitoring ........ ........ ........ ......... ........ ........ ........ ........ ......... ........ ....... 45 System Fault Monitoring....... ......... ........ ........ ........ ......... ........ ........ ........ ......... ........ 45 Communication Fault Monitoring........ ........ ........ ........ ......... ........ ........ ........ ......... .... 45 Power Monitoring.................................................................................................... 45
8/11/2019 725C Instruction Manual Rev 0.1
3/134
Series 725C Instruction Manual
Page 3 of 134
Card Fault Monitoring......... ........ ........ ........ ......... ........ ........ ........ ......... ........ ........ ... 45
S ECTION 6 INDIVIDUAL CHANNEL REPEAT RELAYS .......... ........... 46 Input Follower......................................................................................................... 46 Logic Follower........................................................................................................ 46 Display Follower ..................................................................................................... 46
S ECTION 7 - TYPICAL 725C REAR VIEWS........ .......... ........... ............. . 47 Typical Large Window Version........ ........ ......... ........ ........ ........ ........ ......... ........ ....... 47 Typical Medium Window Version ........ ........ ......... ........ ........ ........ ......... ........ ........ ... 48 Typical Small Window Version.............. ........ ........ ........ ........ ......... ........ ........ ........ .. 49
S ECTION 8 - INSTALLATION ........... ........... ............. ........... ........... ....... 50 Unpacking.............................................................................................................. 50 Mounting................................................................................................................ 50 Panel Mounting ...................................................................................................... 50
Annunciator depth... .... .... .... .... .... .... .... ... .... .... ... .... .... .... ... .... .... ... .... .... ... .... .... ... .... .. 50 19 Rack Mounting.................................................................................................. 51 Wall Mounting ........................................................................................................ 51 Floor Standing........................................................................................................ 51
S ECTION 9 - SOFTWARE INSTALLATION.......... ........... ............. .......... 52 USB Com Port Allocation ........ ........ ......... ........ ........ ........ ......... ........ ........ ........ ...... 52
Auto Detect Hardware Configuration. .... .... .... .... .... .... .... .... .... .... ... .... .... ... .... .... ... .... .. 53 Load from a Saved File.. ........ ........ ........ ......... ........ ........ ........ ........ ......... ........ ....... 53 Create a New System ............................................................................................. 54 File Menu............................................................................................................... 54 New Configuration .................................................................................................. 54 Open Configuration.............. ......... ........ ........ ........ ......... ........ ........ ........ ......... ........ 54 Save Configuration (*.rtk) ........ ........ ......... ........ ........ ........ ......... ........ ........ ........ ...... 54 Print....................................................................................................................... 54 Print Legends ......................................................................................................... 55 Export Legends ...................................................................................................... 55
Exit ........................................................................................................................ 55 View Menu ............................................................................................................. 56 Normal View........................................................................................................... 56
Advanced View.... .... .... .... .... .... ... .... .... ... .... .... ... .... .... .... ... .... .... ... .... .... ... .... .... ... .... .. 56 Front View.............................................................................................................. 57 Rear View .............................................................................................................. 58 Tools Menu ............................................................................................................ 59 Send Settings......................................................................................................... 59 Receive Settings..................................................................................................... 60 Restore System Settings to Default.... ........ ........ ........ ......... ........ ........ ........ ......... .... 61 Help....................................................................................................................... 61
About Configurator...... .... .... .... .... .... .... ... .... .... ... .... .... .... ... .... .... ... .... .... ... .... .... ... .... .. 61
S ECTION 10 AUTO DETECT HARDWARE........... ........... ............. ...... 62
Auto Detect Hardware Configuration. .... .... .... .... .... .... .... .... .... .... ... .... .... ... .... .... ... .... .. 62
S ECTION 11 CREATE A NEW SYSTEM ........... ........... ............. .......... 63 Physical Size Tab ................................................................................................... 63 Window Size .......................................................................................................... 63 Windows Wide........................................................................................................ 63 Windows High ........................................................................................................ 64 Pushbutton Module................................................................................................. 64 Window Configuration Tab ........ ........ ........ ........ ........ ......... ........ ........ ........ ......... .... 65 Mixed Window Sizes............................................................................................... 65 Repeat Relays and Power Tab ........ ......... ........ ........ ........ ......... ........ ........ ........ ...... 66 No Repeat Relays................................................................................................... 66 Repeat Relays........................................................................................................ 66 Power Supply ......................................................................................................... 67 External Power Supply. ........ ......... ........ ........ ........ ......... ........ ........ ........ ......... ........ 67
8/11/2019 725C Instruction Manual Rev 0.1
4/134
Series 725C Instruction Manual
Page 4 of 134
Integral Power Supply ............................................................................................. 67 Alarm Inputs and Remote Pushbuttons Tab... .... .... .... .... .... .... .... ... .... .... ... .... .... ... .... .. 68 Alarm Inputs .... .... .... .... .... .... .... ... .... .... ... .... .... ... .... .... .... ... .... .... ... .... .... ... .... .... ... .... .. 68 Number of Remote Pushbuttons ........ ........ ........ ........ ......... ........ ........ ........ ......... .... 69 Common Relays..................................................................................................... 71
S ECTION 12 SAVED CONFIGURATIONS........... ........... ............. ........ 73 Open Configuration.............. ......... ........ ........ ........ ......... ........ ........ ........ ......... ........ 73
S ECTION 13 SYSTEM SETTINGS ........... ........... ............ ........... ......... 74 General Tab........................................................................................................... 74 Plant Name ............................................................................................................ 74 Description............................................................................................................. 74 Tag No................................................................................................................... 74 Serial No................................................................................................................ 74 WR1 Tab................................................................................................................ 75 Relay 1 4 (Available on all standard systems) ........ ........ ........ ........ ......... ........ ....... 75 Relay 1 to 8 (Relay 5 to 8 - Optional) ........ ........ ........ ........ ......... ........ ........ ........ ...... 75 WR2 Tab................................................................................................................ 76 Relay 1 to 12 (Relay 5 to 12 Optional) ........ ........ ........ ........ ......... ........ ........ ........ .. 76 Group Relay........................................................................................................... 77 Pushbutton............................................................................................................. 77 Fault Relay............................................................................................................. 78 Summary of Fault Relay function ........ ........ ......... ........ ........ ........ ......... ........ ........ ... 78 Field Contact.......................................................................................................... 78 System .................................................................................................................. 78 Comms ................................................................................................................. 78 Card ...................................................................................................................... 78 Coil Status ............................................................................................................. 78 Reflash Pulse Length.............................................................................................. 79 Local Pushbuttons Tab ........ ......... ........ ........ ........ ......... ........ ........ ........ ......... ........ 80 Remote Pushbuttons Tab........ ........ ......... ........ ........ ........ ......... ........ ........ ........ ...... 80
Additional Pushbutton Groups .... .... .... .... .... .... ... .... .... .... ... .... .... ... .... .... ... .... .... ... .... .. 81 Sleep Mode............................................................................................................ 82 Inhibit..................................................................................................................... 83 Internal Horns Tab .................................................................................................. 84 Test Volume........................................................................................................... 85
Auto Acknowledge Tab ...... .... .... .... .... .... .... .... ... .... .... .... ... .... .... ... .... .... ... .... .... ... .... .. 86 Auto Silence Tab .... .... .... .... .... .... .... .... ... .... .... ... .... .... .... ... .... .... ... .... .... ... .... .... ... .... .. 87 Group Operations Tab ............................................................................................ 88
S ECTION 14 CHANNEL SETTINGS................ ........... ............. ........... . 89 Channel Tab .......................................................................................................... 89
Alarm Legend..... .... .... .... .... .... .... .... .... ... .... .... ... .... .... .... ... .... .... ... .... .... ... .... .... ... .... .. 90 Show the Legends .................................................................................................. 90 Print the Legends ........ ........ ......... ........ ........ ........ ......... ........ ........ ........ ......... ........ 90 Export the Legends ........ ........ ........ ........ ......... ........ ........ ........ ........ ......... ........ ....... 91 Manual Inhibit......................................................................................................... 91 Inhibit Input ............................................................................................................ 91 Group 1 to Group 8................................................................................................. 91 Colour.................................................................................................................... 92 Input Tab ............................................................................................................... 92 Contact Type.......................................................................................................... 92 Delay Timers.......................................................................................................... 92
Abnormal Delay (ms) .... ... .... .... ... .... .... ... .... .... ... .... .... .... ... .... .... ... .... .... ... .... .... ... .... .. 92 Normal Delay (ms).................................................................................................. 93 Field Contact Voltage. ........ ........ ........ ........ ......... ........ ........ ........ ......... ........ ........ ... 93 Contact Fault Monitoring ......................................................................................... 94 Relay Tab .............................................................................................................. 95 Coil Status ............................................................................................................. 95 Relay Function ....................................................................................................... 95
8/11/2019 725C Instruction Manual Rev 0.1
5/134
8/11/2019 725C Instruction Manual Rev 0.1
6/134
Series 725C Instruction Manual
Page 6 of 134
Procedures for Factory Repair and Return Warranty ........ ........ ........ ........ ......... ...... 129 RMA FORM ......................................................................................................... 130
SECTION 19 - FACTORY DEFAULT SETTINGS.............. ........... ......... 131
8/11/2019 725C Instruction Manual Rev 0.1
7/134
Series 725C Instruction Manual
Page 7 of 134
SECTION 1 - INTRODUCTION
GeneralThe RTK 725C Series alarm annunciator is used to inform the operator that a
process has gone beyond set limits using visual and audible alarms.
The Annunciator is manufactured from universal cells, each 60mm x 60mm,which can be assembled in an array to provide the number of rows andcolumns required to suit individual panel designs. Each cell within theannunciator is able to contain either:- one large, two medium or four smallalarm windows and each window is illuminated by plug-in universal whiteLEDs assemblies providing a maintenance free solution, a reduction in powerconsumption and the units run at cooler temperatures.
Large, Medium & Sm all Window Sizes
Programmable FeaturesThe 725C is fully programmable allowing the user to enable or disable anumber of pre-defined features to suit individual application. A USBprogramming port is provided behind the pushbutton face plate which can beconnected via a USB port to a suitable laptop / PC running the RTK suppliedconfiguration software utility. Selection of features is on a per channel basiswith no special tools or programming knowledge required.
When the Annunciator is in the CAL mode the user can:-
Dynamically view the current status of all signal inputs.
Set the non alarm state of the alarm input to N/O or N/C on per channelbasis as described in later sections.
8/11/2019 725C Instruction Manual Rev 0.1
8/134
Series 725C Instruction Manual
Page 8 of 134
Glossary of Terms
Cell: A single module 60mm x 60mm which can be joined to adjacentcells in varying heights and widths to provide the number ofalarms required. The number of alarms available per Celldepends on the window size required.
N/C: A Normally Closed contact which opens in the abnormal state.
N/O: A Normally Open contact which closes in the abnormal state.
EN: Energised Relay Coil that De-Energises in the abnormal state.
DE-EN: De-Energised Relay Coil that Energises in the abnormal state.
Form A: Normally Open Single Pole, Single Throw Relay (SPST) contactthat Closes in the abnormal state.
Form B: Normally Closed Single Pole, Single Throw Relay (SPST)contact that Opens in the abnormal state.
Form C: Changeover contacts, Single Pole, Double Throw (SPDT)contact both poles change in the abnormal state.
FCV: Field Contact Voltage. (Wetting Voltage)
Card: Refers to individual electronic circuit boards. There are varioustypes of Cards used within the 725C i.e. Alarm Cards, RelayCards and Supply Cards.
8/11/2019 725C Instruction Manual Rev 0.1
9/134
8/11/2019 725C Instruction Manual Rev 0.1
10/134
Series 725C Instruction Manual
Page 10 of 134
Ground Detection X Not FittedG Internal Ground Detection card fitted
Additional Remote Pushbutton Inputs (3 per card)
X Not Fitted1 A 1 = 3 x additional remote pushbutton Inputs fitted to9 = 27 x additional remote pushbutton Inputs fitted
A = 30 x additional remote pushbutton Inputs fitted to
Common Relay Cards (4 per card) X Not Fitted
1 7 1 = 4 x additional common relays fitted to7 = 28 x additional common relays fitted
Special Options X Not Fitted
1 Z Reserved for Special Options
8/11/2019 725C Instruction Manual Rev 0.1
11/134
Series 725C Instruction Manual
Page 11 of 134
Product OverviewThe 725C is a modular alarm annunciator constructed from 60mm x 60mmcells to form a single unit suitable for mounting in a panel cut-out. Thismodular design allows units to be constructed in vast range of heights and
widths to suit individual panel designs and allows systems to be supplied froma single alarm to a maximum of 256 alarms per annunciator.
System Front View
Typical Small Window Version
Typical Medium W indow Version
Typical Large Window Version
8/11/2019 725C Instruction Manual Rev 0.1
12/134
Series 725C Instruction Manual
Page 12 of 134
Each 60mm x 60mm cell within the annunciator can contain 1, 2 or 4 alarmsdepending on the required window size:-
Window Style Window Size (W x H) Alarms per CellLarge 60mm x 60mm 1
Medium 60mm x 30mm 2Small 30mm x 30mm 4
Integral Pushbutton LocationWhen viewing the front of the annunciator the bottom right hand corner isnormally reserved for the integral pushbutton module.
If advised at the time of order the following alternatives are available
1. The integral pushbutton module can be placed in any cell within theannunciator.
2. The integral pushbutton module can be replaced with active alarmchannels and remote pushbuttons can be used to control the alarmannunciator.
8/11/2019 725C Instruction Manual Rev 0.1
13/134
Series 725C Instruction Manual
Page 13 of 134
Window IlluminationEach channel is illuminated by white Plug-In LEDs which offer amaintenance free solution, lower heat dissipation and lower powerconsumption. Each LED assembly is equipped with 2 pins that allows it be
plugged into the 2 pin socket in the cell behind each alarm window.
CB7028-0RTK
POLARITYMARKING
FRONT VIEW SIDE VIEW
725B CELL PINS
Please note the CB7028POP1 white LED assembly is factory fitted with thehalf circle in the top left hand corner as shown above. If it is inserted upsidedown, no damage will occur but the LED will not function. To remove the LEDassembly a pair of pin-nosed pliers can be used on the sides of the circuitboard to gently pull the assembly towards you. The number of LEDs requiredper window is governed by the window size.
Small window versions use a single LED assembly
Medium window versions use two LED assemblies Large window versions use four LED assemblies
Window ColoursEach channel is equipped with its own removable lens assembly, which,contains a coloured filter and a laser printed film legend. White is used instandard applications but coloured filters can be used as an alternative toprovide a clear indication of alarm type. For example Red can be used for tripalarms, amber for pre-alarms and green for status.
A choice of Six colours are available:- White, Red, Amber, Yellow, Green orBlue.
8/11/2019 725C Instruction Manual Rev 0.1
14/134
Series 725C Instruction Manual
Page 14 of 134
Adding or Changing Film LegendsEach lens assembly has a small slot in the upper ridge of the surround bezel,which allows a flat blade terminal screwdriver to be used to gently lever theassembly from the annunciator. Once the assembly has been removed the
lens, coloured filter and film legend can be accessed by gently pushingoutwards on the side of the inside face of the bezel to allow the lens to clearthe associated moulding tabs.
TAHH-32ATEMPERATURE
ALARMHIGH-HIGH
COLOURED FILTER
FILM LEGENDSLOT TO LEVERTHE BEZEL OUT
BEZELLENS
Filter & Bezel Spare Parts Numbers
Part Small Window Medium Window Large WindowBezel ML-7227-S ML-7227-M ML-7227-L
Lens ML-7228-S ML-7228-M ML-7228-L
Red filter ML-7229-RD ML-7229-RD ML-7229-RD
Amber filter ML-7229-AM ML-7229-AM ML-7229-AM
Yellow filter ML-7229-YL ML-7229-YL ML-7229-YL
Blue filter ML-7229-BL ML-7229-BL ML-7229-BL
Green filter ML-7229-GN ML-7229-GN ML-7229-GN
Laser Printed LegendsFilm legends can be easily created in a style, size, font and language usingMicrosoft Excel or the RTK supplied configuration software.
Once the legend details have been entered they can be laser printed ontooverhead transparency film and placed between the clear front lens of thewindow assembly and the associated coloured filter as shown above.
8/11/2019 725C Instruction Manual Rev 0.1
15/134
Series 725C Instruction Manual
Page 15 of 134
Window Numbering SystemRTK have adopted the following window numbering system to aid with thelocation of the film legend and the associated alarm cards.
This method is used to ensure that the legend matches the functions selectedfor the designated alarm.
2
1 5
6
4
3RESETMUTE
SYSTTEST
FIRSTRESET
LAMPTEST ACK ACK
FIRSTRESET
SYSTTEST
MUTE
LAMPTEST
RESET
FIRSTRESET
3
2
1
SYSTTEST
LAMPTEST
MUTE
ACK
RESET
1 2
43
5 6
87
9 10
11 12
Large Window Version Medium Window Version Small Window Version
WD
COM
PWR
F C WD
COM
PWR
FC WD
COM
PWR
FC
Pushbutton Module On standard systems the Pushbutton / Programming module is located in thebottom right hand corner of the Annunciator when viewed from the front.
Six Pushbuttons are available to allow the user to control all of the customerselectable ISA sequences and four green status LED bars are used to monitorlogic power, field contact power, watchdog and internal communicationsstates.
8/11/2019 725C Instruction Manual Rev 0.1
16/134
Series 725C Instruction Manual
Page 16 of 134
The LEDs indicate
1. PWR = 24VDC logic power2. FC = Field contact power & contact loop resistance monitoring
3. COM = Communications4. WD = Watchdog
When 24VDC is initially applied to the unit the four green LED bars illuminatein sequence whilst the system starts and once the start up routine is completethe LEDs stay ON if all functions are fully operational.
Although the Pushbutton Module is normally integrally mounted it can besupplied as a stand alone item suitable for panel mounting, DIN-rail mountingor wall mounting. The remote pushbutton module can be connected to asingle or group of annunciators using RTK supplied ribbon cables to connectcommon signals.
If the pushbutton module is hinged down the user is able to access the USBprogramming port, dynamically view the status of the associated plant inputsor manually configure the alarm inputs for use with N/O or N/C contacts
USB Programming portThis port is used to view the current configuration or to update the settings ofthe 725C and full details of programming are provided in later sections of thismanual.
8/11/2019 725C Instruction Manual Rev 0.1
17/134
Series 725C Instruction Manual
Page 17 of 134
Plant StatusIf the CAL switch shown above is placed into the ON position the LED bars onthe front of the pushbutton assembly flash in sequence to indicate that the unithas been placed in CAL mode.
Once placed into CAL mode each window on the 725C indicates the dynamicstatus of the associated plant inputs.
If the window is OFF the associated input is OPEN
If the window is ON the associated input is CLOSED
Please note: The OPEN and CLOSED indication refers to the customers fieldcontact and is not related to the non alarm normally open or closed state setin the annunciator.
Configuring Alarm Inputs for use with N/O or N/C field contactsWhen the CAL switch is placed in the ON position the function of the integralpushbuttons changes as detailed below.
Pushbutton Abbreviation Function in CAL ModeLamp Test CHDN Channel Down
Ack FDN Function DownMute SET SetReset SET SetSystem Test CHUP Channel UpFirst Reset FUP Function Up
These functions are indicated on the inside face of the pushbutton assemblyin the circles associated with each pushbutton. These abbreviations areshown for reference only the pushbutton must be used to activate eachfunction.
Select FunctionWhen the unit is first switched to CAL mode it will be in the contact monitoring
state. To change the mode to the set input state the First Reset, (functionUp), pushbutton must be pressed. This action is confirmed when the top lefthand window flashes to indicate that the 1st channel is in programming mode.
Navigating between channels:-The user is able to navigate to the required channel by pressing the SystemTest and Lamp Test Pushbutton.
8/11/2019 725C Instruction Manual Rev 0.1
18/134
Series 725C Instruction Manual
Page 18 of 134
Setting the Non Alarm Input StateOnce the user has navigated to the required channel each time the Mute, orReset, pushbutton is pressed the input state is inverted from N/O to N/C.
If the status LED is OFF the channel is suitable for use with N/O
contacts.
If the status LED is ON the channel is suitable for use with N/Ccontacts.
CAUTION :- This information is only saved when the user navigates to anotherchannel (up or down). If the user places the CAL switch to the OFF positionwithout navigating to an adjacent channel the information will not be stored.
Remote Pushbutton Module As an alternative the 725B can be fully equipped with alarm windows and thePushbutton Module can be supplied as a remote item or the user can useconventional panel mounting momentary, N/O, pushbuttons to control theannunciator.
In these applications the common watchdog / relay, WR, card part noCB6641POP2 is equipped with a USB programming port which is located onthe underside of the associated cell. Full details are provided in section 2 ofthis manual
Audible AlarmsTwo audible alarms are provided as standard behind the pushbutton modulefor use as critical and non critical audibles. Each channel can be software setto activate either of the horns and the volume of each horn can be adjusted inthe software as required.
8/11/2019 725C Instruction Manual Rev 0.1
19/134
8/11/2019 725C Instruction Manual Rev 0.1
20/134
Series 725C Instruction Manual
Page 20 of 134
A Cell - Differential Input Version
AINPUTS
1 2 3 4 3C2C1C 4C
CHANNEL
CUSTOMERINPUTS
CELL 1 - REAR VIEW
5 - 8 ALARM CARD VERSIONS USED IN "A" CELLS(LOWER SLOT)
CB6611POP9 - 24/125V DIFFERENTIAL INPUT VERSION
CB6611POP10 - 48/250V DIFFERENTIAL INPUT VERSION
Cell type A is used to provide:-
Four isolated digital inputs for use with volt-free or powered contacts
The drawing above indicates the OPTIONAL differential input versionwhere each channel is provided with a fully isolated bi-polar input.
8/11/2019 725C Instruction Manual Rev 0.1
21/134
8/11/2019 725C Instruction Manual Rev 0.1
22/134
Series 725C Instruction Manual
Page 22 of 134
AR Cell - Differential Input Version
ARINPUTS
1 2 3 4 3C2C1C 4C
CHANNEL
CUSTOMERINPUTS
CELL 1 - REAR VIEW
5 - 8
R3 R4R2R1
RELAY OUTPUTS
ALARM CARD VERSIONS USED IN "AR" CELLS(LOWER SLOT)
CB6613POP1 (4) CHANNEL RELAY CARD
RELAY CARD VERSION USED IN "AR" CELLS(UPPER SLOT)
CB6611POP9 - 24/125V DIFFERNTIAL INPUT VERSION
CB6611POP10 - 48/250V DIFFERENTIAL INPUT VERSION
Cell type AR is used to provide:-
Four isolated digital inputs for use with volt-free or powered contacts
Four repeat relays providing volt-free contact outputs for use with thirdparty devices
Each of the output contacts can be set to N/C or N/O using a 3 wayheader and 2 way shorting bar located on the card.
The coil state can be programmed to be either EN or DE-EN per relay
The drawing above indicates the standard card types available for cell type AR
8/11/2019 725C Instruction Manual Rev 0.1
23/134
Series 725C Instruction Manual
Page 23 of 134
AP Cell Detail (Alarm P ushbutton Cell)
APINPUTS
1 2 3 4 P2P1C P3
CHANNEL
CUSTOMERSVOLT FREEINPUTS
CELL 0 - REAR VIEW
1 - 4
EXTERNALPUSHBUTTONINPUTS
CB6611POP3 - 24/125V SIGNAL INPUT VERSION PLUS 3 x PUSHBUTTON INPUTS
CB6611POP4 - 48/250V SIGNAL INPUT VERSION
PLUS 3 x PUSHBUTTON INPUTS
ALARM CARD VERSIONS USED IN "AP" CELLS(LOWER SLOT)
Cell type AP is used to provide:-
Four digital inputs for use with volt-free or powered contacts Three external pushbutton inputs for use with optional remote
mounting pushbuttons as required.
Each of the external pushbutton inputs can be programmed to operateas either:- Lamp Test, Silence, Acknowledge, Reset, 1 st Reset orSystem Test or Sleep Mode as required.
The drawing above indicates the standard card types available for celltype AP.
Multiple AP cells may be used in applications that require more than 3x pushbutton inputs or in systems using multiple pushbutton groups tocontrol selective channels
8/11/2019 725C Instruction Manual Rev 0.1
24/134
Series 725C Instruction Manual
Page 24 of 134
APR Cell Detail (Alarm / Pushbutton Relay Cell)
APRINPUTS
1 2 3 4 P2P1C P3
CHANNEL
CUSTOMERSVOLT FREEINPUTS
CELL 0 - REAR VIEW
1 - 4
EXTERNALPUSHBUTTONINPUTS
RELAY OUTPUTS
R1 R2 R4R3
RELAY CARD VERSION USED IN "APR" CELLS(UPPER SLOT)
CB6613POP1 (4) CHANNEL RELAY CARD
CB6611POP3 - 24/125V SIGNAL INPUT VERSION PLUS 3 x PUSHBUTTON INPUTS
CB6611POP4 - 48/250V SIGNAL INPUT VERSION
PLUS 3 x PUSHBUTTON INPUTS
ALARM CARD VERSIONS USED IN "APR" CELLS(LOWER SLOT)
Cell type APR is used to provide:-
Four digital inputs for use with volt-free or powered contacts
Three external pushbutton inputs for use with optional remotemounting pushbuttons as required.
Each of the external pushbutton inputs can be programmed to operateas either:- Lamp Test, Silence, Acknowledge, Reset, 1 st Reset orSystem Test or Sleep Mode as required.
Four repeat relays providing volt-free contact outputs for use with thirdparty devices
Each of the output contacts can be set to N/C or N/O using a 3 wayheader and 2 way shorting bar located on the card.
The coil state can be programmed to be either EN or DE-EN per relay
The drawing above indicates the standard card types available for celltype APR.
Multiple APR cells may be used in applications that require more than3 x pushbutton inputs or in systems using multiple pushbutton groupsto control selective channels.
8/11/2019 725C Instruction Manual Rev 0.1
25/134
Series 725C Instruction Manual
Page 25 of 134
AS Cell Detail (Alarm S upply Cell)
POWER CARD VERSION USED IN "AS" CELLS(UPPER SLOT)
CB6617POP1 POWER CARD 85-264VAC or 88-360VDC
2A / T
CUSTOMERSVOLT FREEINPUTS
4C
CHANNEL
1 2
5 - 8
INPUTS
1C3 4 2C 3C
AS
CELL 1 - REAR VIEW
PSU
N L
CB6611POP1 - 24/125V SIGNAL INPUT VERSION
CB6611POP2 - 48/250V SIGNAL INPUT VERSION
ALARM CARD VERSIONS USED IN "AS" CELLS(LOWER SLOT)
Cell type AS is used to provide:-
Four digital inputs for use with volt-free or powered contacts
Universal Input Power Supply capable of accepting either:-
AC voltages in the range 85-264VAC or
DC voltages in the range 88-360VDC
The Power Supply card is located in the upper card slot as typicallyshown above.
The power supply is suitable for use with a number of cells whichvaries depending on the window size used and the options fitted.
Multiple power supply cards can be used in larger annunciators.
The drawing above indicates the standard card types available for celltype AS
8/11/2019 725C Instruction Manual Rev 0.1
26/134
Series 725C Instruction Manual
Page 26 of 134
AS Cell - Differential Input Version
CUSTOMERINPUTS
AS
2C
5 - 8CHANNEL
1 2 3
INPUTS
4 1C 3C 4C
LN
CELL 1 - REAR VIEW
2A / T
PSU
POWER CARD VERSION USED IN "AS" CELLS
(UPPER SLOT)
CB6617POP1 POWER CARD 85-264VAC or 88-360VDC
ALARM CARD VERSIONS USED IN "AS" CELLS(LOWER SLOT)
CB6611POP9 - 24/125V DIFFERENTIAL INPUT VERSION
CB6611POP10 - 48/250V DIFFERENTIAL INPUT VERSION
Cell type AS is used to provide:-
Four Isolated digital inputs for use with volt-free or powered contacts
Universal Input Power Supply capable of accepting either:-
AC voltages in the range 85-264VAC or
DC voltages in the range 88-360VDC
The Power Supply card is located in the upper card slot as typicallyshown above.
The power supply is suitable for use with a number of cells which
varies depending on the window size used and the options fitted.
Multiple power supply cards can be used in larger annunciators.
The drawing above indicates the standard card types available for celltype AS
8/11/2019 725C Instruction Manual Rev 0.1
27/134
8/11/2019 725C Instruction Manual Rev 0.1
28/134
8/11/2019 725C Instruction Manual Rev 0.1
29/134
Series 725C Instruction Manual
Page 29 of 134
WR Cell Detail (Watchdog - Relay Cell)
WR
RELAY OUTPUTS
CR1
REAR VIEW
CB6641POP1 - WATCHDOG / RELAY CARD
RELAY CARD VERSION USED IN "WR" CELLS(LOWER SLOT)
CR2 CR3 CR4
Cell type WR is used to provide:-
WR cells are equipped with a four channel relay card which provide
Four Common Relays which can be programmed for use as horn,common alarm or diagnostic watchdog relays
Each of the output contacts can be set to N/C or N/O using a 3 wayheader and 2 way shorting bar located on the card.
The non alarm coil state of each relay can be programmed to be eitherEN or DE-EN.
8/11/2019 725C Instruction Manual Rev 0.1
30/134
Series 725C Instruction Manual
Page 30 of 134
WRS Cell Detail (Watchdog / Relay - Supply Cell)
WRS
RELAY OUTPUTS
CR1
REAR VIEW
CB6641POP1 - WATCHDOG / RELAY CARD
RELAY CARD VERSION USED IN "WRS" CELLS(LOWER SLOT)
CR2 CR3 CR4
CB6617POP1 POWER CARD 85-264VAC or 88-360VDC
POWER CARD VERSION USED IN "WRS" CELLS(UPPER SLOT)
2A / T
PSU
N L
Cell type WRS is used to provide:-
WR cells are equipped with a four channel relay card which provide
Four Common Relays which can be programmed for use as horn,common alarm or watchdog relays
Each of the output contacts can be set to N/C or N/O using a 3 wayheader and 2 way shorting bar located on the card.
The non alarm coil state of each relays can be programmed to beeither EN or DE-EN
Universal Input Power Supply capable of accepting:-
AC voltages in the range 85-264VAC or
DC voltages in the range 88-360VDC
The Power Supply card is located in the upper card slot and thecommon relay card is located in the lower card slot as typically shownabove.
The power supply is suitable for use with a number of cells whichvaries depending on the window size and options required
Multiple power supply cards can be used in larger annunciators asrequired.
8/11/2019 725C Instruction Manual Rev 0.1
31/134
Series 725C Instruction Manual
Page 31 of 134
WRR Cell Detail (Watchdog / Relay - Relay Cell)
WRR
CR1
REAR VIEW
CB6641POP1 - WATCHDOG / RELAY CARD
RELAY CARD VERSION USED IN "WRR" CELLS(LOWER SLOT)
CR2 CR3 CR4
RELAY CARD VERSION USED IN "WRR" CELLS(UPPER SLOT)
CB6613POP1 - (4) CHANNEL RELAY CARD
CR5 CR6 CR7 CR8
RELAY OUTPUTS
RELAY OUTPUTS
Cell type WRR is used to provide:-
WRR cells are equipped with two four channel relay cards which provide
Eight Common Relays which can be programmed for use as horn,common alarm or diagnostic watchdog relays
Each of the output contacts can be set to N/C or N/O using a 3 wayheader and 2 way shorting bar located on the card.
The non alarm coil state of each relay can be programmed to be eitherEN or DE-EN
8/11/2019 725C Instruction Manual Rev 0.1
32/134
Series 725C Instruction Manual
Page 32 of 134
Optional WR Cell Detail (Watchdog - Relay Cell) used on systems notequipped with integral Pushbutton / Programming Modules
WR
RELAY OUTPUTS
CR1
REAR VIEW
RELAY CARD VERSION USED IN "WR" CELLS(LOWER SLOT)
CR2 CR3 CR4
CB6641POP2 - WATCHDOG / RELAY CARDFOR USE WITH SYSTEMS NOT EQUIPPEDWITH INTEGARL PUSHBUTTONS
This version of Cell type WR is used on systems that are not equipped withthe integral pushbutton / programming module.
This version of the WR cell is equipped with a four channel relay card plus aUSB programming port which provide
Four Common Relays which can be programmed for use as horn,common alarm or diagnostic watchdog relays
Each of the output contacts can be set to N/C or N/O using a 3 wayheader and 2 way shorting bar located on the card.
The non alarm coil state of each relay can be programmed to be eitherEN or DE-EN.
USB Programming port which is located on the underside of theassociated cell to allow the unit to be programmed.
8/11/2019 725C Instruction Manual Rev 0.1
33/134
8/11/2019 725C Instruction Manual Rev 0.1
34/134
Series 725C Instruction Manual
Page 34 of 134
SECTION 3 LO GIC SUPPLY & FUSING
All 725C Alarm Annunciators operate from a 24VDC logic supply.
Externally Powered SystemsWhen external power supplies are used 24VDC must be connected toterminals OV and +V as shown below. Fuse F1, (5 x 20mm 8A), is providedon the underside of the power input card to protect the alarm logic and+24VDC is internally linked to all of the associated cards within the system.Red LED F1 is used to indicate that the +V fuse has blown.
REAR VIEW
OV OV +V+V 0VC +VC
Rx F1 F2 Tx
FROM EXTERNAL24VDC SUPPLY
(+)
(OV)UNDERSIDE VIEW OFPOWER INPUT CARD
F 18A
F21A
LOGICFUSE
8A
SIGNALFUSE
1A
SI/O Card Versions
Part No DescriptionCB6648POP1 Used on standard versions with remote power supplies
8/11/2019 725C Instruction Manual Rev 0.1
35/134
8/11/2019 725C Instruction Manual Rev 0.1
36/134
Series 725C Instruction Manual
Page 36 of 134
SECTION 4 - SIGNAL SUPPLY VOL TAGE SETTING
24V or 125V AC/DC Signal Inputs
On standard 725C systems each 4 channel alarm card is suitable for use with24V or 125V AC/DC signal inputs.
Each channel on the alarm card is equipped with a 3 pin header and 2 wayshorting bar that allows the user to set the input to match the required signalinput voltage level.
L K 1
L K 2
L K 3
L K 4
125V 24V
24V125V
125V 24V
OR
L K 1
L K 1
SIGNAL SUPPLYVOLTAGE SETTING
CHANNEL 1
CHANNEL 1
CHANNEL 2
CHANNEL 4
CHANNEL 3
SIGNAL SUPPLYSET TO 24V
SIGNAL SUPPLYSET TO 125V
The above settings are available on the following (4) channel alarm cards
Card Type FeaturesCB6611POP1 24/125V Signal InputCB6611POP3 24/125V Signal Input plus 3 x Pushbutton Inputs
Differential Input Versions
Card Type FeaturesCB6611POP9 24/125V Differential Signal Inputs
8/11/2019 725C Instruction Manual Rev 0.1
37/134
Series 725C Instruction Manual
Page 37 of 134
48V or 250V AC/DC Signal Inputs
As an option each 4 channel alarm card can be supplied suitable for use with48V or 250V AC/DC signal inputs.
Each channel on the alarm card is equipped with a 3 pin header and 2 wayshorting bar that allows the user to set the input to match the required signalinput voltage level.
L K 1
L K 2
L K 3
L K 4
250V 48V
48V250V
250V 48V
OR
L K 1
L K 1
SIGNAL SUPPLYVOLTAGE SETTING
CHANNEL 1
SIGNAL SUPPLYSET TO 48V
SIGNAL SUPPLYSET TO 250V
CHANNEL 3
CHANNEL 4
CHANNEL 2
CHANNEL 1
The above settings are available on the following (4) channel alarm cards
Card Type FeaturesCB6611POP2 48/250V Signal InputCB6611POP4 48/250V Signal Input plus 3 x Pushbutton Inputs
Differential Input Versions
Card Type FeaturesCB6611POP10 48/250V Differential Signal Inputs
8/11/2019 725C Instruction Manual Rev 0.1
38/134
Series 725C Instruction Manual
Page 38 of 134
24VAC/DC Signal Inputs
WR
725B SMALL WINDOW VERSION TYPICAL REAR VIEW
OV OV +V+V OVC +VC
Rx F1 F2 Tx
CHANNEL
21
5 - 8
3C
INPUTS
43 1C 2C
A
4C
APINPUTS
CHANNEL
31 2 1C4
1 - 4
P3P1 P2CR1 CR2 CR3 CR4
F2 - 1A
EXT PB
INTERNAL SIGNALSUPPLY COMMON
24VDC SIGNAL SUPPLYLINKED FROM THE
LOGIC SUPPLY
CELL 2 CELL 1 CELL 0
+V
Each channel on the alarm card is provided with a 3 pin header and 2 wayshorting bar which allows the user to select the inputs to operate on either24VAC/DC or 125VAC/DC.
On standard 725C systems the 24VDC logic supply is linked as follows - OVand OVC and +V and +VC this provides a 24VDC signal contact supply on allC terminals as shown above.
LED F2 is used to indicate that the signal supply, (+VC), fuse has blown.
As all *C terminals are internally linked the customer can connect each inputcontact to a dedicated terminal as shown in the middle cell or a single feedcan be used for multiple contacts as shown in the right hand cell.
Inputs are bi-polar and therefore 24VAC or 24VDC can be used as a signalsupply however if 24VAC is required the link between the logic supply and thesignal supply must be removed and the 24VAC must be externally sourced.
The common return for all remote pushbuttons is +V (+24VDC)
8/11/2019 725C Instruction Manual Rev 0.1
39/134
8/11/2019 725C Instruction Manual Rev 0.1
40/134
8/11/2019 725C Instruction Manual Rev 0.1
41/134
Series 725C Instruction Manual
Page 41 of 134
Optional 250VAC/DC Signal Inputs
WR
725B SMALL WINDOW VERSION TYPICAL REAR VIEW
OV OV +V+V OVC +VC
Rx F1 F2 Tx
250VAC/DC SIGNAL
CHANNEL
21
5 - 8
3C
INPUTS
43 1C 2C
A
4C
APINPUTS
CHANNEL
31 2 1C4
1 - 4
P3P1 P2CR1 CR2 CR3 CR4
F2 - 1A
SUPPLY VOLTAGE
EXT PB
INTERNAL SIGNALSUPPLY COMMON
CELL 2 CELL 1 CELL 0
+V
Note:- In applications that require 250VAC/DC signal inputs RTK supplyoptional 4 channel alarm cards in place of the standard version
250VAC/DC Signal SupplyEach channel on the alarm card is provided with a 3 pin header and 2 wayshorting bar which allows the user to select the inputs to operate on either48VAC/DC or 250VAC/DC.
On 725C systems where 250VAC/DC is required as a signal supply voltagethis needs to be derived externally and connected to terminals OVC and +VCas typically shown above.
LED F2 is used to indicate that the signal supply fuse has blown.
Fuse F2, (5 X 20mm 1A), is provided on the power input card to protect thesignal supply voltage and the 24VDC is internally linked to all associated inputcard *C terminals to allow distribution to the external field contacts.
As all *C terminals are internally linked the customer can connect each inputcontact to a dedicated terminal as shown in the middle cell or a single feedcan be used for multiple contacts as shown in the right hand cell.
Inputs are bi-polar and therefore an externally derived 250VAC or 250VDCcan be used as a signal supply as required.
The common return for all remote pushbuttons is +V (+24VDC)
8/11/2019 725C Instruction Manual Rev 0.1
42/134
Series 725C Instruction Manual
Page 42 of 134
Optional Differential Input Version As an option RTK can supply fully isolated inputs for each alarm way.
As the Inputs are bi-polar the user can switch AC or DC voltages as required.
WR
725B SMALL WINDOW VERSION TYPICAL REAR VIEW
OV OV +V+V OVC +VC
Rx F1 F2 Tx
CHANNEL
21
5 - 8
3C
INPUTS
43 1C 2C
A
4C
AINPUTS
CHANNEL
31 2 1C4
1 - 4
4C2C 3CCR1 CR2 CR3 CR4
EXT PB
INTERNAL SIGNALSUPPLY COMMON
CELL 2 CELL 1 CELL 0
(+) (+) (+) (+) (-)(-) (-)(-)
TYPICAL CUSTOMERSUPPLIED
24VDC INPUTS
C H
- 5
C H
- 6
C H
- 7
C H
- 8
C H
- 5
C H
- 6
C H
- 7
C H
- 8
C H
- 1
C H
- 2
C H
- 3
C H
- 4
C H
- 1
C H
- 2
C H
- 3
C H
- 4
TYPICAL CUSTOMERSUPPLIED
24VDC INPUTS
(+) (+) (+)(+)(-)(-) (-) (-)
In the above typical example cell 0 is shown with OV switched inputs and cell1 is shown with +24V switched inputs
Standard 24V/125V AC/DC Version Each (4) channel alarm card is provided with a 3 pin header and 2 way jumperlink per channel which allows the user to select the input for use with either24V or 125V as required.
Optional - 48V/250V AC/DC Version
Each (4) channel alarm card is provided with a 3 pin headers and 2 way jumper link which allows the user to select the input for use with either 48V or250V as required.
8/11/2019 725C Instruction Manual Rev 0.1
43/134
Series 725C Instruction Manual
Page 43 of 134
SECTION 5 COMMO N REL A YS
WR
RELAY OUTPUTS
CR1
REAR VIEW
CB6641POP1 - WATCHDOG / RELAY CARD
RELAY CARD VERSION USED IN "WR" CELLS(LOWER SLOT)
CR2 CR3 CR4
Four common relays are located in the WR Cell within the Annunciator asshown above. Each relay is equipped with a C/O contact and the user canselect the contact state to N/C or N/O using a 3 way header and 2 wayshorting bar located on the card as shown below.
NO LK3 NC
RL3
OR
NO LK4 NC
NO LK4 NC
NORMALLY
OPEN
NORMALLYCLOSED
RL4
RELAYCONTACT
STATENO LK4 NC
RL2 RL1
NO LK1 NCNO LK2 NC
CARD ADDRESSDIL SWITCH SW1
SW1
The coil state of each relay can be set to EN or DE-EN as described in thesoftware configuration section of this manual.
Multiple common relay cards may be present in larger systems to provide thenecessary features.
8/11/2019 725C Instruction Manual Rev 0.1
44/134
Series 725C Instruction Manual
Page 44 of 134
The function of each relay can be set within the software allowing the relay tooperate as:-
Group Relay
Groups can be used within an Annunciator for alarms which need to be linkedto form first-up, common alarm or audible groups. Once groups have beendefined the functionality of each group can be set using the GROUPOPERATION settings within the software.
The following group operation settings are available:-
Input Follower RelayIn applications where common alarm groups are required the group operationcan be set to input. Any common relay can be linked to any input group toprovide a volt-free summary contact for customer use.
The common relay will activate when any alarm in the group is in theabnormal state and the relay will remain active until all inputs in the grouphave returned to normal.
Alarm Follower RelayIn applications where common alarm groups are required the group operationcan be set to alarm. Any common relay can be linked to any alarm groupwhich will provide a volt-free summary contact for customer use.
The common relay will activate when any alarm in the group is in theabnormal state and the relay will remain active until all inputs in the grouphave returned to normal and the alarm has been cleared using the relevantpushbuttons.
Audible Follower RelayChannels within the Annunciator can be software linked into groups which canbe used to drive either of the internal audible alarms or they can be linked toany of the common relays to provide a volt-free contact to drive externalaudible alarms.
The common relay will activate when an alarm occurs and will remain activeuntil the silence or acknowledge pushbutton is operated.
Pushbutton Follower Relay Any common relay can be set to follow the action of any of the pushbuttonfunctions. The group operation should be set to match the required functioni.e. if Lamp Test is selected the common relay contact will activate insympathy when the Lamp Test Pushbutton is pressed.
Diagnostic / Watchdog Relay Any common relay can be set to operate as diagnostic / watchdog relays toprovide a volt free contact for use with 3 rd party devices to indicate that a faulthas occurred within the annunciator.
8/11/2019 725C Instruction Manual Rev 0.1
45/134
8/11/2019 725C Instruction Manual Rev 0.1
46/134
Series 725C Instruction Manual
Page 46 of 134
SECTION 6 INDIVIDUAL CHA NNEL RE PEA T RELA YS
Each four channel alarm card can be supplied with an optional four channelrelay card, part no CB6613POP1, which plugs into the alarm card andprovides the user with a volt-free contact per alarm channel for use with 3 rd Party devices.
Each relay is equipped with a C/O contact and the user can select the contactstate to N/C or N/O using a 3 way header and 2 way shorting bar located onthe card as shown below
OR
NO
RL1
NC
L K 1
L K 2
NC
NO
RL2 L K 3
NC
RL3
NO
NC
NO
L K 4
RL4
CB6613POP1REPEAT RELAY
CARD
NC
NO
L K 4
L K 4
SIDE VIEW
NO
NC
NORMALLYOPEN
NORMALLYCLOSED
RELAYCONTACT
STATE
Each relay can be configured in software to operate in accordance with one ofthe following:-
Input FollowerThe relay changes state each time there is a change to the associated signalinput contact.
Logic FollowerThe relay changes state on alarm and remains in the abnormal state until theinput has returned to normal and the logic has been reset using thepushbuttons associated with the ISA sequence set for this channel.
Display FollowerThe relay changes state on alarm and faithfully follows the display window i.e.Flashing, Steady or Off depending on the alarm sequence selected for thischannel.
8/11/2019 725C Instruction Manual Rev 0.1
47/134
Series 725C Instruction Manual
Page 47 of 134
SECTION 7 - TYPICAL 725C REA R VIEWS
The following details are provided as typical examples of 725C Annunciatorrear views showing alarm inputs, remote pushbutton inputs, common alarmrelay outputs, 24VDC logic and signal wiring
Typical Large Window Version ,(each alarm window = 60mm w x 60mm h)
WR
OV OV +V+V OVC +VC
Rx F1 F2 Tx
24VDC SIGNAL
CR1 CR2 CR3 CR4F2 - 1A
SUPPLY VOLTAGE
24VDC LOGICSUPPLY VOLTAGE
INTERNAL SIGNALSUPPLY COMMON
CHANNEL AP
P1
EXT. PBINPUTS
2 31 4 C P3P2
1 - 4
2C
INPUTS
2 31 1C4 4C3C
A5 - 7CHANNEL
CELL 6 CELL 4 CELL 2 CELL 0
CELL 3CELL 7 CELL 5 CELL 1
+V
The above rear view shows a typical large window 725C annunciator 4 cellswide x 2 cells high with seven active alarms, common relay card and anintegral pushbutton module.
Each cell within the Annunciator is used to display a single channel.
In the example shown the top right hand cell is equipped with a four channelalarm card plus provision for three remote pushbutton inputs.
In large window versions of the 725C only the first cell in a group of four issupplied with an alarm card and the outputs are distributed to the next threecells working down in columns then moving onto the next row.
8/11/2019 725C Instruction Manual Rev 0.1
48/134
8/11/2019 725C Instruction Manual Rev 0.1
49/134
Series 725C Instruction Manual
Page 49 of 134
Typical Small Window Version , (each alarm window = 30mm w x 30mm h),
WR
OV OV +V+V OVC +VC
Rx F1 F2 Tx
CR1 CR2 CR3 CR4F2 - 1A
24VDC LOGICSUPPLY VOLTAGE
INTERNAL SIGNALSUPPLY COMMON
CHANNEL AP
P1
EXT. PBINPUTS
2 31 4 C P3P2
1 - 4
2C
INPUTS
2 31 1C4 4C3C
A17 - 20CHANNEL
1 2 4C1C43 3C2C
INPUTS
ACHANNEL9 - 12
1 2 4C1C43 3C2C
INPUTS
ACHANNEL25 - 28
321 4 1C 2C 3C 4CINPUTS
ACHANNEL21 - 24
1 2 4CINPUTS
1C43 3C2C
CHANNEL13 - 16 A
1INPUTS
3 42 2C 3C1C 4C
5 - 8CHANNEL
A
24VDCSIGNALSUPPLY VOLTAGE
CELL 6 CELL 4 CELL 2 CELL 0
CELL 7 CELL 5 CELL 3 +VCELL 1
The above rear view shows a typical small window 725C configured 4 cellswide x 2 cells high with twenty eight active alarms, common relay card and anintegral pushbutton module.
Each cell within the Annunciator is used to display four alarm channels.
In the example shown the top right hand cell is equipped with a four channelalarm card plus provision for three remote pushbutton inputs.
In small window versions of the 725C each cell is supplied with an alarm cardand the outputs are distributed to four channels within the cell.
8/11/2019 725C Instruction Manual Rev 0.1
50/134
Series 725C Instruction Manual
Page 50 of 134
SECTION 8 - INSTAL LA TION
UnpackingOnce the item has been unpacked please visually examine the unit for anysigns of transit damage before installing the unit into the control system. If anydamage has occurred please report the damage to the freight forwarder andcopy RTK. The alarm annunciator is supplied with panel mounting clampslocked in place, however please check all packages to ensure that noadditional pieces are left in the box as any auxillary items like power supplies,horns, pushbuttons or spares kits will be packed separately.
Please double check that all items listed on the packing list have beenunpacked before disposing of any packing material.
MountingStandard 725C units are designed for panel mounting, as an option they canbe supplied fitted within 19 filler plates to allow direct mounting into Industrystandard 19 rack systems or fully integrated into wall or floor standing panels.
Panel Mounting
CABINET DIMENSIONS IN MMWIDE HIGH
Cells Overall Cut-Out Cells Overall Cut-Out1 88 74 1 88 74
2 148 134 2 148 1343 208 194 3 208 1944 268 254 4 268 2545 328 314 5 328 3146 388 374 6 388 3747 448 434 7 448 4348 508 494 8 508 4949 568 554 9 568 554
10 628 614 10 628 61411 688 674 11 688 674
12 748 734 12 748 73413 808 794 13 808 79414 868 854 14 868 85415 928 914 15 928 91416 988 974
X
16 988 974
Please note:-The cut out tolerance should be with 2mm.
Annunciator depth is 143mm
8/11/2019 725C Instruction Manual Rev 0.1
51/134
8/11/2019 725C Instruction Manual Rev 0.1
52/134
Series 725C Instruction Manual
Page 52 of 134
SECTION 9 - SOFTWA RE INSTALL ATIONInsert the Installation CD into the associated drive and a welcome screen willappear advising the user that a wizard will guide them through the initialsetup.
USB Com Port Allocation As part of the installation a USB com port is assigned to a dedicated port andthis is used to communicate with the 725C. The setting is retained by theconfiguration software but can be manually adjusted if another PC is used.
To check which com port has been allocated standard Windows navigationtechniques can be used to select My Computer, Control Panel, System,Hardware Tab, Device Manager, Ports and the allocated com port will beshown as USB Serial Port (COM3 in the example below).
.
This port number must be used in the configuration utility to successfully
upload or download data to the 725C.
Once the software has loaded a software wizard will guide the user throughthe remaining screens
8/11/2019 725C Instruction Manual Rev 0.1
53/134
8/11/2019 725C Instruction Manual Rev 0.1
54/134
Series 725C Instruction Manual
Page 54 of 134
Create a New System After the software has loaded the user is able to access the following Menus.
File Menu
The File Menu provides access to the following:-.
New ConfigurationSelecting the File menu followed by New Configuration allows the user tostart the configuration process from the very beginning. Please note:- Thisoption automatically refreshes all of the associated fields to the defaultcondition, it is therefore recommended that the user save any existingconfigurations first.
Open Configuration
Selecting the File Menu followed by Open Configuration allows a previouslysaved configuration file to be uploaded. Standard Microsoft Windows navigation techniques allow the user to locate the file and a left mouse clickon the Open command button uploads the configuration for review ormodification.
Save Configuration (*.rtk)Once the user has created a new or modified an existing configuration theassociated file can be saved using the File Menu followed by SaveConfiguration. Standard Microsoft Windows navigation techniques can be
used to define the location and after a file name has been defined a leftmouse click on the Save command button completes the process.
PrintThe configuration software provides access to front or rear views of theannunciator and these views can be printed if required. Once the Print menuhas been selected additional sub menus are available to allow selection ofprinter type, page size, orientation etc.
8/11/2019 725C Instruction Manual Rev 0.1
55/134
Series 725C Instruction Manual
Page 55 of 134
Print LegendsThe Configuration software allows the user to define the alarm legends foreach channel as described later in this manual. Once the Legend details havebeen entered into the software the user can produce laser printed acetate filmlegends using the Print Legends Menu.
Export Legends As an alternative the user can export the Legend details for future referenceusing the Export Legends Menu and standard Microsoft Windows navigationtechniques to save the associated Windows Excel file.
ExitThe Exit Menu allows the user to quit the application but please ensure that
you save any configuration changes before selecting exit.
8/11/2019 725C Instruction Manual Rev 0.1
56/134
Series 725C Instruction Manual
Page 56 of 134
View MenuThe following options are available under the View menu
Normal ViewIn the Normal View the number of groups displayed is limited to 8. A max of32 Groups are available within the 725C for use as Horn, First Up or Common
Alarm groups and the additional groups are accessed under the advancedview.
Advanced ViewIn more complex applications the Advanced View allows full access to all 32groups and other advanced features within the annunciator as shown in theexample below.
8/11/2019 725C Instruction Manual Rev 0.1
57/134
Series 725C Instruction Manual
Page 57 of 134
Show LegendsThe alarm text and colour for each alarm way can be displayed on theannunciator graphic using the View menu followed by the Show Legendsas shown below.
As a default the window colour is Red and the channel number is used toidentify each alarm way. The user is able to edit the alarm text and colour ofeach channel to provide a clearer view and to aid navigation within thesoftware.
Front View
The front view of the alarm Annunciator is displayed by default to simplifyconfiguration. This view is defined under the View menu followed by FrontView as shown below.
8/11/2019 725C Instruction Manual Rev 0.1
58/134
8/11/2019 725C Instruction Manual Rev 0.1
59/134
Series 725C Instruction Manual
Page 59 of 134
Tools Menu
The following options are available under the Tools menu
Send SettingsSelecting the Send Settings menu allows the user to transmit theconfiguration to the associated 725C Annunciator. Once selected theCommunications Port will be displayed and the Send command key shouldbe pressed using a left mouse click.
Once selected a status bar is used to provide a visual indication of progressas shown below.
The software will monitor the data lines and if communication is notestablished an Error screen will appear as shown below.
8/11/2019 725C Instruction Manual Rev 0.1
60/134
Series 725C Instruction Manual
Page 60 of 134
Receive SettingsSelecting the Receive Settings menu allows the user to receive theconfiguration from the associated 725C Annunciator. Once selected the
Communications Port will be displayed and the Read command key shouldbe pressed using a left mouse click.
Once selected a status bar is used to provide a visual indication of progressas shown below.
The software will monitor the data lines and if communication is notestablished an Error screen will appear as shown below
8/11/2019 725C Instruction Manual Rev 0.1
61/134
Series 725C Instruction Manual
Page 61 of 134
Restore System Settings to DefaultIf the software has been used to trial configurations the unit can be returned tofactory default settings using the Tools menu followed by Restore SystemSettings to Default as shown below.
CAUTIONThis setting will automatically convert ALL of the Systems options to thefactory default setting and therefore it should only be used with caution. Fulldetails of default settings are provided in the rear of this manual.
HelpDynamic help screen provide help for specific features as required. At anytime the user can select the Help Menu to access information on theselectable features of the 725C.
The user is able to search by topic and navigate forward and backwardswithin the help call out screens as required.
About ConfiguratorThis allows the user to view the revision number of the configuration software
8/11/2019 725C Instruction Manual Rev 0.1
62/134
Series 725C Instruction Manual
Page 62 of 134
SECTION 10 A UTO DETE CT HA RDWA RE.
The user is able to Auto Detect Hardware Configuration as follows:-
Insert the Installation CD into the associated drive and a welcome screen willappear advising the user that a wizard will guide them through the initialsetup.
To configure a 725C please select the 725 radio button using a left mouseclick.
Once the 725 radio button has been checked the user is prompted to selectone of three options:- To upload the factory configuration select Auto DetectHardware Configuration
Auto Detect Hardware Configuration.If a 725C System is connected to the associated PC and communication hasbeen established the software will be able to read the configuration data directfrom the annunciator system. Once upload is complete the Annunciatorgraphic should match the supplied instrument and the associated fields willindicate all of the configured features.
Please refer to Section 6 & 7 for details of conf igurabl e options
8/11/2019 725C Instruction Manual Rev 0.1
63/134
Series 725C Instruction Manual
Page 63 of 134
SECTION 11 CREA TE A NEW S YSTEMThis section is only required for trial purposes or when creating configurationsfrom scratch. In standard applications the user can upload a configurationdirect from the Annunciator. Once the information has been uploaded it canbe reviewed / modified as required and a copy can be saved to the local PCand downloaded to the Annunciator as required.
If the user selects Create a New System all of the following parameters willneed to be defined.
Physical Size Tab A drop-down menu is provided to the right of each of the following three fieldsto allow the cabinet to be defined. The graphical view of the Annunciator isdynamically updated as selections are made.
Window SizeThe window size defines the number of windows available in each 60mm x60mm cell in accordance with the following chart.
Window Style Window Size (W x H) Alarms per CellLarge 60mm x 60mm 1
Medium 60mm x 30mm 2Small 30mm x 30mm 4
Windows WideOnce a window size has been assigned the user is able to select the totalnumber of windows wide within the range defined below.
Window Style WINDOWS WIDELarge Selectable from 1 to 16 Wide
Medium Selectable from 1 to 16 WideSmall Selectable in pairs from 2, 4, 6, 8, 10, 12, 14 to 16 Wide
8/11/2019 725C Instruction Manual Rev 0.1
64/134
Series 725C Instruction Manual
Page 64 of 134
Windows HighOnce a window size has been assigned the user is able to select the totalnumber of windows high within the range defined below.
Window Style WINDOWS HIGHLarge Selectable from 1 to 16 Wide
Medium Selectable from 1 to 16 WideSmall Selectable in pairs from 2, 4, 6, 8, 10, 12, 14 to 16 Wide
Pushbutton ModuleStandard 725C Systems are supplied with an integral pushbutton /programming module located in the bottom right hand corner of the
Annunciator when viewed from the front as typically shown below.
To enable the integral pushbutton function the tick-box to the left of thePushbutton Module field needs to be checked using a left mouse and theannunciator graphic is automatically updated. If the tick-box is left uncheckedthe pushbutton module will be not be shown on the graphic.
In standard systems the Pushbutton module is located in the bottom righthand corner as shown above.
Once the user has configured the basic unit a left mouse click on the Nextcontrol button navigates to the Window Configuration screen. This screen isonly required in applications that use mixed window sizes.
The Next control b utton can be used to pr oceed w ith con figurat ion.
8/11/2019 725C Instruction Manual Rev 0.1
65/134
Series 725C Instruction Manual
Page 65 of 134
Window Configuration TabThis section is only used in systems supplied with mixed window sizes onstandard system the user can bypass this screen using the Next controlbutton.
Mixed Window SizesThe Window Configuration Tab allows the user to define the window style ofeach cell. A left mouse click on one of the four cells shown under the tabautomatically copies the style. The selection is confirmed when a red borderappears around the icon as typically shown below. A left mouse click into anycell in the annunciator graphic pastes the style.
The Next control b utton can be used to proceed w ith con figurat ion.
8/11/2019 725C Instruction Manual Rev 0.1
66/134
Series 725C Instruction Manual
Page 66 of 134
Repeat Relays and Power TabThis tab provides access to the fields associated with optional repeat relay perchannel facilities and Integral Power Supplies.
No Repeat RelaysOn standard systems there individual channel repeat relays are not fitted andtherefore the drop down menu is set to No Repeat Relays.
Repeat Relays As an option each channel can be supplied with a dedicated repeat relayfacility to provide an isolated output for use with 3 rd party devices. In theseapplications the drop-down menu needs to be set to Repeat Relays asshown below.
Dual Repeat Relays As an option each channel can be supplied with dual repeat relays to providetwo isolated outputs for use with 3 rd party devices. In these applications thedrop-down menu needs to be set to Dual Repeat Relays as shown below
8/11/2019 725C Instruction Manual Rev 0.1
67/134
Series 725C Instruction Manual
Page 67 of 134
Power Supply725C Systems operate on a logic voltage of 24VDC and this can be suppliedvia External or Internal Power Supplies.
External Power SupplyIn Systems using an externally derived 24VDC the drop down menu under thePower Supply Field needs to set to be External Power Supply as shownbelow.
Integral Power SupplyIf the annunciator system is directly powered from 72 to 144VDC or 85 to264VAC integral power supplies are used to convert to 24VDC and the dropdown menu needs to be set to Integral Power Supply.
The Next control b utton can be used to pr oceed w ith con figurat ion.
8/11/2019 725C Instruction Manual Rev 0.1
68/134
Series 725C Instruction Manual
Page 68 of 134
Alarm Inputs and Remote Pushbuttons Tab
Alarm InputsStandard systems use optically isolated digital inputs fed via a volt-free
contact or externally powered device. In these applications the standard inputYES radio button is checked as shown below..
If NO is checked the differential input feature is enabled.
8/11/2019 725C Instruction Manual Rev 0.1
69/134
Series 725C Instruction Manual
Page 69 of 134
Number of Remote PushbuttonsOn standard 725C Systems 3 control Inputs are available on the first alarmcard in the system for use with external control inputs.
Example 1 :- Remote Pushbuttons only
Function Required Number of Remote Inputs RequiredSystem Test 1
Acknowledge 1Reset 1Total 3
In this application the 3 control inputs provided as standard are sufficient
The Number of Remote Pushbuttons Field should be set to 3 as shownbelow.
Example 2 :- Remote Pushbuttons plus Inhibit Group Inputs
Function Required Number of Remote Inputs RequiredLamp Test 1Silence 1
Acknowledge 1Reset 1Inhibit Group 1 1Inhibit Group 2 1Total 6
In this application 3 control inputs are provided on the first alarm card in the
system and a second alarm card would be provided with 3 control inputs.
The Number of Remote Pushbuttons Field should be set to 6 as shownbelow.
8/11/2019 725C Instruction Manual Rev 0.1
70/134
Series 725C Instruction Manual
Page 70 of 134
Example 3 :- Remote Pushbuttons plus Sleep Mode Input
Function Required Number of Remote Inputs RequiredSystem Test 1
Acknowledge 11st Reset 1Sleep Mode 1Total 4
In this application 3 control inputs are provided on the first alarm card in thesystem and a second alarm card would be provided with 3 control inputs. (2available for future use)
The Number of Remote Pushbuttons Field should be set to 6.
Example 4 :- 2 x Remote Pushbutton Groups plus 2 Group Inhibit
Function Required Number of Remote Inputs RequiredPushbutton Group 1System Test 1
Acknowledge 11 st Reset 1Pushbutton Group 2System Test 1
Acknowledge 11 st Reset 1InhibitInhibit Group 1 1Inhibit Group 2 1Total 8
In this application 3 control inputs are provided on the first alarm card in thesystem and two additional alarm cards would each be provided with 3 controlinputs. (1 available for future use).
The Number of Remote Pushbuttons Field should be set to 9.Error MessageIf the number of Remote Pushbutton Inputs selected exceeds the number of
Alarm cards available a warning message appears to advise the user that theconfiguration is not possible.
8/11/2019 725C Instruction Manual Rev 0.1
71/134
Series 725C Instruction Manual
Page 71 of 134
Common Relays A four channel common relay card is provided as standard and each relay canbe assigned to a group, fault or pushbutton.
Example 1 :- 1 Horn, 2 Common Alarm and 1 Fault Relay
Function Required Number of Common RelaysHorn Relay 1Group 1 Relay 1Group 2 Relay 1System Fault Relay 1Total 4
In this application the 4 common relays provided as standard are sufficient.
The Number of Common Relays Field should be set to 4 as shown below.
Example 2 :- 2 Horn, 3 Common Alarm and 1 Fault Relay
Function Required Number of Common Relays
Horn Group 1 Relay 1Horn Group 2 Relay 1Group 1 Relay 1Group 2 Relay 1Group 3 Relay 1System Fault Relay 1Total 6
In this application the 4 common relays provided as standard are insufficientand an additional 4 channel common relay card would be provided.
8/11/2019 725C Instruction Manual Rev 0.1
72/134
Series 725C Instruction Manual
Page 72 of 134
Example 3 :- 2 Horn, 3 Common Alarm, 1 Acknowledge Output and 1 FaultRelay
Function Required Number of Common RelaysHorn Group 1 Relay 1
Horn Group 2 Relay 1Group 1 Relay 1Group 2 Relay 1Group 3 Relay 1
Ack PB Follower 1System Fault Relay 1Total 7
In this application the 4 common relays provided as standard are insufficientand an additional 4 channel common relay card would be provided.
The Number of Common Relays Field should be set to 8.
Error MessageIf the number of Relays selected exceeds the space available a warningmessage appears indicating how many relays cannot be fitted.
The Next control b utton can be used to proceed w ith con figurat ion.
8/11/2019 725C Instruction Manual Rev 0.1
73/134
Series 725C Instruction Manual
Page 73 of 134
SECTION 12 SA VED CONFIGURA TIONS
Open ConfigurationThe File and Open Configuration menu provide normal Microsoft Windowsnavigation allowing a previously saved configuration to be opened from thestored location. Once a previous configuration file has been opened the usercan review configuration settings as detailed in Section 6 & 7.
8/11/2019 725C Instruction Manual Rev 0.1
74/134
Series 725C Instruction Manual
Page 74 of 134
SE CTION 13 SYSTEM S ETTINGS
General TabThe fields listed under the General tab allow the user to uniquely identifyeach Alarm Annunciator System to aid with the storage and retrieval ofconfiguration data.
The user can update any of the fields within the software but the changes willonly be saved after the Confirm Settings control button is pressed using aleft mouse click.
Plant NameIn the example shown above the annunciator is located in RTK InstrumentsLtd.
DescriptionThis field is used to identify the specific plant area or annunciator functionwithin the plant..
Tag No.This field allow a Customer assigned number to be used to identify a uniquealarm annunciator.
Serial No. A serial number is automatically provided once the software is communicatingwith the alarm annunciator.
8/11/2019 725C Instruction Manual Rev 0.1
75/134
Series 725C Instruction Manual
Page 75 of 134
WR1 TabThe WR1 Tab, (Watchdog / Relay), allows the user to assign any of thecommon relays for use as a Group, Pushbutton Follower or Fault Relays.
On standard 725C systems one 4 channel relay card is used to providecommon relays.
Relay 1 4 (Available on all standard systems) A drop-down menu is accessed using a left mouse click on the control buttonassociated with each Relay. This menu is used to assign define whether theRelay operates as a Group, Pushbutton Follower or Fault Relays.
In some applications users require more than 4 common relays, in theseinstances a single or multiple 4 channel relay cards can be used to expandthe system.
The WR1 Tab provides configuration for a maximum of 8 Relays.
Relay 1 to 8 (Relay 5 to 8 - Optional)In the example below one additional 4 Channel Relay card has been fitted,providing 8 Relays in total.
If more than 8 Relays are installed two WR* Tabs will be available toconfigure Relays 9 onwards, as shown in the following typical examples.
8/11/2019 725C Instruction Manual Rev 0.1
76/134
Series 725C Instruction Manual
Page 76 of 134
WR2 Tab
Relay 1 to 12 (Relay 5 to 12 Optional)
In the example below a total of 12 Relays are fitted with Relay 1 to 8 beingconfigured under the WR1 Tab and the remaining Relays being configuredunder the WR2 Tab.
This pattern continues as shown below, (4 Relays per additional card),
No of Common Relays WR* Tab No Relay No4 WR1 1 to 4
WR1 1 to 48WR1 1 to 4
WR1 1 to 4WR1 1 to 412WR2 1 to 4WR1 1 to 4WR1 1 to 4WR2 1 to 4
16
WR2 1 to 4ETC
8/11/2019 725C Instruction Manual Rev 0.1
77/134
Series 725C Instruction Manual
Page 77 of 134
Group Relay.Each Channel within the Annunciator can be assigned to a single or multipleGroups. These Groups can be software linked to any of the common relays toprovide contact outputs for use with 3 rd Party devices.
In the example below Relay 1 is being assigned to Group 1 and a left mouseclick would complete the selection.
Once the Relay has been assigned the Control Button is automaticallyupdated to indicate its function. I.E. Relay 3 has been assigned to Group 2and Relay 4 has been assigned as a System Fault Relay.
Pushbutton Any one of the Common Relays can be assigned to any of the Pushbuttonfunctions shown below. In this example Relay 1 has been assigned as aSilence Pushbutton Follower and each time the Silence Pushbutton is
activated on the Annunciator the contacts on Relay 1 will change state.
8/11/2019 725C Instruction Manual Rev 0.1
78/134
Series 725C Instruction Manual
Page 78 of 134
Fault Relay. Any of the Common Relays can be assigned to a diagnost