INSTALLATION MANUAL
DIGITAL FULL COLOR
MULTIFUNCTIONAL SYSTEM
MX-2640NMX-3140NMX-3640NMODEL
Transit, Installation (using) environment, Note
1. Installing (use) conditions
A. Transportation space
B. Installing space
C. Power source (Capacity, voltage, frequency,
safety, plug)
(1) Power capacity
Current capacity
(2) Power voltage
(3) Power frequency, waveform
(4) Safety
(5) Power plug
D. Floor strength and level
E. Direct rays of the sun, dust, temperature,
humidity, gasses, chemicals, vibration
(1) Temperature and humidity (Environmental
conditions)
No. Content
11-13/16"
(30cm)
11-13/16"
(30cm)
17-23/32"
(45cm)
Operational environment
(2) Contaminates
(3) Direct sunlight
(4) Gases and chemicals
(5) Vibration
F. Note for handling PWB and electronic parts
85%
Humidity RH
60%
20%
G. Note for proper drum, developing, fusing and
transfer unit handling
Drum unit
Transfer unit
Developing unit
Fusing unit
2. Transit and delivery
A. Implements, facility, and manpower
B. Delivery
3. Relationship between the model name and the designation in description of the document
No. Content Method
Model name Designation in description
[2] MX-2640N/3140N/3640N (MAIN UNIT)
1. Unpacking
A. Unpacking
B. Fixing tape and protection material removal
C. Packed items check
No. Name Quantity
1 2
D. Lock release
(1) Tray rotation plate lock release
(2) Scanner (2/3 mirror unit) lock release
2. Installation
A. Developer installation
2
1
3
1
2
B. Set the control level for the reference toner
density
2
1
Color toner cartridge positions
YM
CBK
C. Cleaning
(1) Cleaning of LSU's dust-proof glass and PTC wire
D. Paper feed tray setup
(1) System setting
(2) Tray size setup
E. Specifications setup
Item Description
A
B
SIM No Content
SIM No Content
3. Image quality check
A. Execution items
B. Description
(1) Print engine image distortion adjustment (Manual
adjustment) / OPC drum phase adjustment
(Automatic adjustment) / Color registration
adjustment (Automatic adjustment)
No. Item SIM
EXECUTEAdjustment completed
Abnormal end
Display/
ItemContent Display Default NOTE
(2) Copy color balance and density check
Method 1
1 2 3 4 5 6 7 8 9 10 W
SHARP GRAY CHART
SHARP gray chartPatch 1 is
slightly copied.
Patch 2 is copied.
(Color copy)
1 2 3 4 5 6 7 8 9 10 W
SHARP GRAY CHART
SHARP gray chart
Patch 1 is not copied.
Patch 2 is
slightly copied.
Patch 3 is copied.
( py)
Serviceman chart (Color patch section)
The densities of patches 1 - 6 ofeach color are properly balanced.
Patch 7 is slightlycopied or not copied.
(Color copy)
a. Color copy check items (Check to confirm the following:)
b. Monochrome copy check items (Check to confirm the following:)
Method 2
(3) Printer color balance/density check
Method 1
Method 2
QO PNMLKJIHGFEDCBA
Y
M
C
Bk
Highdensity
1) The max. density section is not blurred.
2) Patch C or D of each of Y, M, C, and BK is very slightly copied.
Lowdensity
CMY
blend
3) Patch for each of Y, M, C, BK
The patch density is identical between patches or not reversed.
The patch density is changed gradually.
PRINTER CALIBRATION
QO PNMLKJIHGFEDCBA
Y
M
C
Bk
1) The max. density section is not blurred.
2) Patch C or D of each of Y, M, C, and BK is very slightly copied.
Low density
CMY
blend
3) Patch for each of Y, M, C, BK
The patch density is identical between patches or not reversed.
The patch density is changed gradually.
High density
(4) Copy/Printer color balance and density adjustment
(Automatic adjustment)
QO PNMLKJIHGFEDCBA
Y
M
C
Bk
Highdensity
Lowdensity
PRINTER CALIBRATION
PRINTER CALIBRATION
1) The max. density section is not blurred.
2) Patch C or D of each of Y, M, C, and BK is very slightly copied.
3) Patch for each of Y, M, C, BK
The patch density is identical between patches or not reversed.
The patch density is changed gradually.
High densityLow density