Assembly Drawing Titles Listing SUPERBA EQUIPMENT
ASSYID TITLE
SI01 EPIC PREBULKERS FOR 200 & 260MM WIDESUPERBA-TYPE YARN HEATSET LINES
SI02 EPIC SUPER COOL-OUT FAN SYSTEMS FOR SUPERBA-TYPE HEATSET LINES
SI03 EPIC DUAL END HYDRAULIC SYSTEMFOR SEALING HEADS ON SUPERBA HEATSET LINES
SI04 EPIC/SIGNAL COOLING ZONES AND REPLACEMENT PARTSFOR SUPERBA-TYPE HEATSET LINES
SI05 EPIC/SIGNAL HANDWAY BLOWERS FOR SUPERBA-TYPE COOLING ZONES
SI06 EPIC MOTOR CONTROL CENTER
SI07 EPIC/SIGNAL ENTRY HEAT ZONE ASSEMBLY
SI07A EPIC/SIGNAL INTERMEDIATE HEAT ZONE ASSEMBLY
SI07B EPIC/SIGNAL EXIT HEAT ZONE ASSEMBLY
SI08 EPIC/SIGNAL RECIRCULATOR BLOWER ASSEMBLYFOR SUPERBA-TYPE HEATSET LINES
SI08A EXPLODED VIEW OF PARTS FOR 212-00 TURBINE FAN & SHAFT ASSEMBLYFOR CBS RECIRCULATED BLOWER ASSEMBLY
SI11 SPARE PARTS FOR SIGNAL OPTIBULK & OPTIBULK EZPREBULKING SYSTEM FOR SUPERBA-TYPE HEATSET
Page 1 of 1March 2008
CLICK ON THE ASSYID NUMBER BELOW TO GO TO THE DRAWING
CLICK BACK ON THE DRAWING TO RETURN HERE
SI01Epic Enterprises, Inc.bmb1.TIF
EPIC PREBULKERS FOR 200 & 260MM WIDESUPERBA-TYPE YARN HEATSET LINES
PREBULKERS ÉPICO PARA 200 Y 260M M ANCHOS
Epic Enterprises, Inc., P.O. Box 979, Southern Pines, NC 28388-0979 USATelephone Toll Free 800-648-7273 or 910-692-5441 Outside USA
Fax Toll Free 888-692-4147 or 910-692-4147 Outside USAWebsite: http://www.epicenterprises.com E-Mail: [email protected]
BACK
SI01Epic Enterprises, Inc.
Position OEM Ref. Nos. Epic No. Description UOM
SI01-01 EE150100 Prebulker, Standard Width (200mm Wide)
Pre-Voluminador, 200mm Ancho
EA
SI01-02 EE150200 Prebulker, Wide Band (260mm Wide)
Pre-Voluminador, 260mm Ancho
EA
Superba is a trademark of Superba SA
Many existing Superba heatset lines are equipped with the older hot water bath type prebulkers with inherent scaling problems (often requiring descaling every 3-4 months) and do not have fans to increase heat penetration. Epic units increase prebulking efficiency as part of increasing total line speed and productivity. Epic Prebulkers use fan-delivered, live steam to speed prebulking efficiency. The steam is brought to the yarn through a bottom-mounted tray in the housing and is then reclaimed through a manifold system. The Epic unit provides the same function as the latest Superba HEP Prebulker design but is much lower in cost. Epic construction is stainless steel in the chamber and manifold.
The Epic Prebulker is equipped with a 4-20 milliamp micro-processor unit that controls steam flow and temperature. Temperature is sensed with a dual element resistance temperature probe. The micro-processor control unit can be connected to an existing Superba computer control system, to an Epic computer control system or can be operated independently.
Maintenance and part replacement is negligible. After very long service, it is possible that a steam valve, controller or valve may have to be replaced. Parts are available from Epic.
The Epic Prebulker is furnished with assembly and operation instructions as well as a complete wiring diagram. Customer must specify voltage.
The 200mm Wide Epic Prebulker is EE150100. The 260mm Wide Unit is Epic Prebulker EE150200.
Epic products are intended as replacements for worn or damaged parts in OEM products. OEM Part numbers in (parenthesis) indicate either 1) Improved design 2) the part serves the same function as the OEM part, but may differ from the OEM design, or 3) it is a component of an assembly where no OEM reference number is available, or 4) it is a repair service for the referenced OEM part.
EE is an Epic trademark designating Epic parts © Epic Enterprises, March 2008
Epic Enterprises, Inc., P.O. Box 979, Southern Pines, NC 28388-0979 USATelephone Toll Free 800-648-7273 or 910-692-5441 Outside USA
Fax Toll Free 888-692-4147 or 910-692-4147 Outside USAWebsite: http://www.epicenterprises.com E-Mail: [email protected]
SI02Epic Enterprises, Inc.bmb3.TIF
EPIC SUPER COOL-OUT FAN SYSTEMS FOR SUPERBA-TYPE HEATSET LINES
SISTEMAS ESTUPENDOS ÉPICOS DEL VENTILADOR DE COOL-OUT PARA LAS LÍNEAS DE
Epic Enterprises, Inc., P.O. Box 979, Southern Pines, NC 28388-0979 USATelephone Toll Free 800-648-7273 or 910-692-5441 Outside USA
Fax Toll Free 888-692-4147 or 910-692-4147 Outside USAWebsite: http://www.epicenterprises.com E-Mail: [email protected]
BACK
SI02Epic Enterprises, Inc.
Position OEM Ref. Nos. Epic No. Description UOM
SI02-01 EE150000 Super Cool-Out Fan for Standard Superba (200mm) (Includes 3 Stainless Steel Roller Assemblies)
Ventilador-"Super Cool-Out", con Conjunto de 3 Rodillos de Acero Inoxidable
EA
SI02-02 EE150000-1 Super Cool-Out Fan for 2-S Superba (260mm) (Includes 3 Stainless Steel Roller Assemblies)
Ventilador - "Super cool-Out", con Conjunto de 3 Rodillos de Acero
EA
SI02-03 EE102004S Roller Assembly, Stainless Steel, (Inlet/Outlet Chamber)
Conjunto de Rodillos de Acero Inoxidable para Camera Entrada y Salida
EA731-230-084720-992-452
SI02-03A EE102004-1S Roller Assembly, Stainless Steel, (Inlet/Outlet Chamber) (Hardened Roller)
Conjunto de Rodillos de Acero Inoxidable para Camera Entrada y Salida (Enduracido)
EA(731-230-084)(720-992-452)
SI02-04 EE150800 Fan Blade for Entrance/Exit Cooling (RTD) Fan on Standard 200mm Superba
Aspa del ventilador para el ventilador que se refresca de Entrance/Exit (RTD) para 200mm Superba
EANot Applicable
SI02-05 EE150801 Motor for Entrance/Exit Cooling (RTD) Fan, on Standard 200mm Superba
Motor para el ventilador que se refresca de Entrance/Exit (RTD) para 200mm Superba
EANot Applicable
SI02-06 EE150803 Stainless Steel Brackets to Mount Fan Shaft, Bearing and Blade to Cool Out Fan on Standard 200mm Superba
Soportes del acero inoxidable para montar el eje, el cojinete y la lámina del ventilador para refrescarse fuera del ventilador para 200mm Superba
EANot Applicable
Cool-out fans are used immediately after the Prebulker to eliminate heat and moisture in the yarn before it goes into the heatset tunnel. They are also used after exit from the heatset tunnel to provide a cool, dry yarn prior to winding. Older Superba cool-out fans were satisfactory only for very slow processing speeds. Some of the components of the Superba cool-out fan systems are sheet steel and subject to rusting. The Epic System is
Epic Enterprises, Inc., P.O. Box 979, Southern Pines, NC 28388-0979 USATelephone Toll Free 800-648-7273 or 910-692-5441 Outside USA
Fax Toll Free 888-692-4147 or 910-692-4147 Outside USAWebsite: http://www.epicenterprises.com E-Mail: [email protected]
SI02Epic Enterprises, Inc.
Superba is a trademark of Superba SA
stainless steel.
Epic Cool-Out Turbine Fans move approximately twice the amount of cooling air through the yarn so it is possible to nearly double speed capabilities. The Epic System has an expanded stainless grid guard to assist in preventing yarn choking of the fan. The Epic System fits both 200mm and 260mm wide band units. The fan units are equipped with OSHA-approved lockout switches. Epic Cool-Out Fan Systems are 100% stainless.
The Epic system comes with installation and operating instructions and a wiring schematic. Customer must specify line voltage so that the correct motor is installed.
The system is very low maintenance. Occasionally, a replacement 12" stainless fan or 3/4HP (0.5KW) motor may need to be replaced. Parts are available from Epic.
Epic products are intended as replacements for worn or damaged parts in OEM products. OEM Part numbers in (parenthesis) indicate either 1) Improved design 2) the part serves the same function as the OEM part, but may differ from the OEM design, or 3) it is a component of an assembly where no OEM reference number is available, or 4) it is a repair service for the referenced OEM part.
EE is an Epic trademark designating Epic parts © Epic Enterprises, March 2008
Epic Enterprises, Inc., P.O. Box 979, Southern Pines, NC 28388-0979 USATelephone Toll Free 800-648-7273 or 910-692-5441 Outside USA
Fax Toll Free 888-692-4147 or 910-692-4147 Outside USAWebsite: http://www.epicenterprises.com E-Mail: [email protected]
SI03Epic Enterprises, Inc.BMB12.TIF
EPIC DUAL END HYDRAULIC SYSTEMFOR SEALING HEADS ON SUPERBA HEATSET LINES
SISTEMA HYDRÁULICO DEL EXTREMO DUAL ÉPICO
Epic Enterprises, Inc., P.O. Box 979, Southern Pines, NC 28388-0979 USATelephone Toll Free 800-648-7273 or 910-692-5441 Outside USA
Fax Toll Free 888-692-4147 or 910-692-4147 Outside USAWebsite: http://www.epicenterprises.com E-Mail: [email protected]
BACK
SI03Epic Enterprises, Inc.
Position OEM Ref. Nos. Epic No. Description UOM
SI03-01 EE150300 Dual End Hydraulic System
Dispositivo de Hidraulica- Fin Doble
EA
Superba is a trademark of Superba SA
Older Superba Power Transformer Units were equipped with a hand pump to create sufficient hydraulic pressure to effect a seal on the heads at both entry and exit ends of the machine. At start-up, it often can take one-two hours or more to create the seal by hand pumping. The original hydraulic and air system needed to initiate or break the seal ran the full length of the machine and was subject to leaks, line breakage, etc.
The complete Epic Hydraulic System EE150300 has two air driven pumps mounted outboard of the line immediately adjacent to the sealing heads. By actuation of the lever in the Epic system the seal can be made on start-up in approximately 10 seconds. The Epic system is similar to Superba's hydraulic system used on the most recent 2S machine and is comparatively very low in cost.
The Epic Dual End System includes two outboard hydraulic systems, mounting brackets, and metering valve distribution blocks. The hydraulic outputs can be connected to existing hydraulic jack lines. The system comes complete with installation and operation instructions as well as a piping diagram. Desired air pressure supplied to the System is 40-60 psi or 3-4 BAR. System maintenance is extremely low. Over an extended period of time, an air pump, valve or gauge may have to be replaced. Parts are available from Epic.
Epic products are intended as replacements for worn or damaged parts in OEM products. OEM Part numbers in (parenthesis) indicate either 1) Improved design 2) the part serves the same function as the OEM part, but may differ from the OEM design, or 3) it is a component of an assembly where no OEM reference number is available, or 4) it is a repair service for the referenced OEM part.
EE is an Epic trademark designating Epic parts © Epic Enterprises, March 2008
Epic Enterprises, Inc., P.O. Box 979, Southern Pines, NC 28388-0979 USATelephone Toll Free 800-648-7273 or 910-692-5441 Outside USA
Fax Toll Free 888-692-4147 or 910-692-4147 Outside USAWebsite: http://www.epicenterprises.com E-Mail: [email protected]
SI04Epic Enterprises, Inc.CBS6.TIF
EPIC/SIGNAL COOLING ZONES AND REPLACEMENT PARTSFOR SUPERBA-TYPE HEATSET LINES
ZONAS DE ENFRIAMIENTO DE EPIC/SIGNAL Y PIEZAS DE RECAMBIO
Epic Enterprises, Inc., P.O. Box 979, Southern Pines, NC 28388-0979 USATelephone Toll Free 800-648-7273 or 910-692-5441 Outside USA
Fax Toll Free 888-692-4147 or 910-692-4147 Outside USAWebsite: http://www.epicenterprises.com E-Mail: [email protected]
BACK
SI04Epic Enterprises, Inc.
Position OEM Ref. Nos. Epic No. Description UOM
SI04-01 CC-CS-100 Cooling Zone, 1.0 Meter, ASME
Zona de Refrigerante, 1.0 Meter
EA
SI04-01A CC-CS-151 Cooling Zone, 1.5 Meter, ASME (Includes 3 EE102004 Stainless Steel Roller Assemblies)
Zona Refrigerante, 1.5 meter con Ensamble de 3 Rodillos de Azero Inoxidable Sopurte de Correa en Zona Refigerante, 1.5 Meter
EA
SI04-01B CC-CS-201 Cooling Zone, 2.0 Meter, ASME (Includes 3 EE102004 Stainless Steel roller Assemblies)
Zona de Refrigerante, 2.0 Meters, con Conjunto de 3 Rodillos de Azero Inoxidable
EA
SI04-01C CC-CS-301 Cooling Zone, 3.0 Meter, ASME (Includes 4 EE102004 Stainless Steel Roller Assemblies)
Zona de Refrigerante, 3.0 Meters con Ensamble de 4 Rodillos de Acero Inoxidable
EA
SI04-02 CC-CS-103-1 Support, 1.0 Meter Cooling Zone Belt
Soparte para correa en Zona refrigerante, 1 Meter
EA
SI04-02A CC-CS-153-1 Support, 1.5 Meter Cooling Zone Belt
Sopurte de corea en Zona Refrigerante, 1.5 Meter
EA30-238
SI04-02B CC-CS-203-1 Support, Cooling Zone Belt, 2.0 Meter
Soporte de Correa en Zona Refrigerante, 2.0 Meter
EA
SI04-02C CC-CS-303-1 Support, Cooling Zone Belt, 3.0 Meter
Soparte de Correa en Zona Refrigerante, 3.0 Meter
EA
SI04-03 CC-CS-104 Coil, Finned Cooling, 1.0 Meter
Rollo de Refrigerante con Aletas, 1.0 Meter
EA
SI04-03A CC-CS-154 Coil, Finned Cooling, 1.5 Meter
Rollo de Refrigerante con Aletas, 1.5 Meter
EA
Epic Enterprises, Inc., P.O. Box 979, Southern Pines, NC 28388-0979 USATelephone Toll Free 800-648-7273 or 910-692-5441 Outside USA
Fax Toll Free 888-692-4147 or 910-692-4147 Outside USAWebsite: http://www.epicenterprises.com E-Mail: [email protected]
SI04Epic Enterprises, Inc.SI04-03B CC-CS-204 Coil, Finned Cooling, 2.0 Meter
Rollo de Refrigerante con Aletas, 2.0 Meter
EA
SI04-03C CC-CS-304 Coil, Finned Cooling, 3.0 Meter
Rollo de Refrigerane con Aletas, 3.0 Meter
EA
SI04-04 260-13 Tunnel Gasket
Guarnicion para Tunel
EA
SI04-05 260-09 Pipe Flange Gasket 8"
Guarnicion, 8"
EA
SI04-06 CC-CS-100-3 Bolt, Handway
Tornillo para Puerto de Mano
EA
SI04-07 CC-CS-103-3 Cover, Condensate Handway (231-02)
Cubierta para Puerta de Mano Para condensasian
EA
SI04-08 CC-CS-103-2 Shield, Cooling Zone Condensate, 1.0 Meter
Protecion de Agua de Condensacion en Zona refrigerante, 1.0 Meter
EA
SI04-08A CC-CS-153-2 Shield, Cooling Zone Condensate, 1.5 Meter
Proteccion de Aqua de Condensacion in Aona Refrigerante
EA30-239
SI04-08B CC-CS-203-2 Shield, Cooling Zone Condensate, 2.0 Meter
Proteccian de agua de Condensacion en Zona Refrigerante, 2.0 Meter
EA
SI04-08C CC-CS-203-2.5 Shield, Cooling Zone Condensate, 2.5 Meter
Proteccion de Agua de Condensacion in Zona Refrigerante, 2.5 Meter
EA
SI04-08D CC-CS-303-2 Shield, Cooling Zone Condensate, 3.0 Meter
Proteccian de Agua den Condensacion en Zona Refrigrante, 3.0 Meter
EA
SI04-09 CC-CS-100-2 Nut, Flange
Tuerca para Brida
EA
SI04-10 CC-CS-100-1 Bolt, Flange
Tornillo para Brida
EA
Epic Enterprises, Inc., P.O. Box 979, Southern Pines, NC 28388-0979 USATelephone Toll Free 800-648-7273 or 910-692-5441 Outside USA
Fax Toll Free 888-692-4147 or 910-692-4147 Outside USAWebsite: http://www.epicenterprises.com E-Mail: [email protected]
SI04Epic Enterprises, Inc.SI04-11 CC-CS-100-4 Nut, Handway
Tuerca para Pueto de Mano
EA
Superba is a trademark of Superba SA
Cooling zones are employed immediately prior to entry into the heatsetting zone and immediately after exit from the heatsetting zone to cool the yarn. Early Superbas came only with an entry end 0.5 meter cooling zone, but did have an exit 2.0 meter cooling zone. Trials proved that better yarn could be produced at a higher speed with longer cooling zones. Early Superba machines are most typically upgraded by adding a 1.5 meter extension to the 0.5 meter entry cooling zone or replacing it with a 2 meter entry cooling zone. Some yarns benefit from even longer 3.0 meter entry and exit zones. The 1.5 and 2.0 meter cooling zones include three Epic EE102004 stainless steel roller assemblies. The 3.0 includes four.
Air in the cooling zone is cooled by chilled water passing through finned stainless cooling coils. Cooling coils fit Epic/Signal cooling zones and are readily adapted to Superba machines.
Also see section on Epic/Signal Handway Blowers for Cooling Zones for increased speed and improved yarn quality.
Epic products are intended as replacements for worn or damaged parts in OEM products. OEM Part numbers in (parenthesis) indicate either 1) Improved design 2) the part serves the same function as the OEM part, but may differ from the OEM design, or 3) it is a component of an assembly where no OEM reference number is available, or 4) it is a repair service for the referenced OEM part.
EE is an Epic trademark designating Epic parts © Epic Enterprises, March 2008
Epic Enterprises, Inc., P.O. Box 979, Southern Pines, NC 28388-0979 USATelephone Toll Free 800-648-7273 or 910-692-5441 Outside USA
Fax Toll Free 888-692-4147 or 910-692-4147 Outside USAWebsite: http://www.epicenterprises.com E-Mail: [email protected]
SI05Epic Enterprises, Inc.HB.TIF
EPIC/SIGNAL HANDWAY BLOWERS FOR SUPERBA-TYPE COOLING ZONESSOPLADORES DE EPIC/SIGNAL HANDWAY
Epic Enterprises, Inc., P.O. Box 979, Southern Pines, NC 28388-0979 USATelephone Toll Free 800-648-7273 or 910-692-5441 Outside USA
Fax Toll Free 888-692-4147 or 910-692-4147 Outside USAWebsite: http://www.epicenterprises.com E-Mail: [email protected]
BACK
SI05Epic Enterprises, Inc.
Position OEM Ref. Nos. Epic No. Description UOM
SI05-01 CC-HB-01 Blower, Handway
Ventilador para Puertade Mano
EA30-022
SI05-02 HB-01 Blower Wheel
Rueda de Ventilador
EA
SI05-03 HB-02 Blower Shaft
Eje de Ventilador
EA30-023
SI05-04NS HB-03 Blower Motor 1HP, (0.66KW), 220/440V
Motor de Ventilador, (0.66KW), 220/440V
EA
SI05-05NS HB-04 Blower Motor Belt
Correa para Motor de Ventilador
EA
SI05-06 HB-05 Blower Housing Side Wall (CALL EPIC FOR PRICING)
Pieza de Proteccion de Ventiador
EA
SI05-07 HB-06 Blower Housing Assembly (CALL EPIC FOR PRICING)
Conjunto de Caja de Ventilador
EA
SI05-08 HB-07 Blower Shaft Pulley
Polea para Eje de Ventilador
EA
SI05-09 HB-08 Blower Shaft Bushing
Buje para Eje de Ventilador
EA
SI05-10NS HB-09 Blower Motor Pulley
Polea para Motor de Vertilador
EA
SI05-11NS HB-10 Blower Motor Bushing
Buje para Motor de Ventilador
EA
SI05-12 214-01 Housing, Packing
Caja para Empoque dura
EA
SI05-13 214-02 Bushing, Brass Housing
Buje de Laton para Caja de Empaquedura
EA30-036
SI05-14 214-03C Packing Material, 5/16" Square X 25" Long, Graphite
Empaquerdura, 5/16" X 25" Largo
EA30-037
SI05-15 214-04 Insert, Brass Housing
Insercion de Laton para Caja
EA30-038
Epic Enterprises, Inc., P.O. Box 979, Southern Pines, NC 28388-0979 USATelephone Toll Free 800-648-7273 or 910-692-5441 Outside USA
Fax Toll Free 888-692-4147 or 910-692-4147 Outside USAWebsite: http://www.epicenterprises.com E-Mail: [email protected]
SI05Epic Enterprises, Inc.SI05-16 214-05 Bolt, Insert Mounting, 3/8-16 SS Stud X
2-1/8" with Nut
Perno y Tuerca para Montage, 3/8-16 SS Stud X 2-1/8"
EA
SI05-17 214-06 O-Ring, Housing, 242 Silicone 4-1/4" OD X 4" ID
Anillo "O", 242 Silicone 4-1/4" OD X 4" ID
EA30-040
SI05-18 214-08 Washer, 3/8", Stainless
Arandela Plana de Acero Inoxidable, 3/8"
EA
SI05-19NS 214-09 Screw, Socket Head Cap, 10-32X1/2"
Tornillo Cilindrico, 10-32X1/2"
EA
SI05-21 214-12 Nut, 3/8-16" Hex
Tuerca, Hexagonal, 3/8-16"
EA
SI05-22 217-02 Bearing Housing
Coja para Rodiamento de Bolas
EA30-043
SI05-23 217-03 Bearing, Shaft, NTN#6206NSL
Rodamiento de Bolas, NTN#6206NSL
EA
SI05-24 217-04 Ring, Inside Snap (#5000-237)
Retenador Internal (#5000-237)
EA
SI05-25 217-05 Ring, Outside Snap (#5100-118)
Retenador External (#5100-118)
EA
Superba is a trademark of Superba SA
Handway Blowers may be fitted to the entry and exit cooling zones of the heatset line at the handway flanges on all tunnels. The cooling zones are cooled by forcing chilled water through the cooling coils within the tunnel. Earlier Superbas were not equipped with these blowers so that the only circulation of cool air was caused by normal air usage needed to pressurize the Superba tunnels. By adding Handway Blowers to the cooling zone ports, the blowers rapidly recirculate the chilled air to provide better cooling, better yarn quality and faster processing speeds or greater productivity.
The Epic/Signal Blowers may readily be installed on cooling zones supplied by both Superba and Epic/Signal.
The drive motor is 220/440V AC. The unit is relatively low maintenance but occasionally parts such as bearings or bushings may need to be replaced.
Epic products are intended as replacements for worn or damaged parts in OEM products. OEM Part numbers in (parenthesis) indicate either 1) Improved design 2) the part serves the same function as the OEM part, but may differ from the OEM design, or 3) it is a component of an assembly where no OEM reference number is available, or 4) it is a repair service for the referenced OEM part.
EE is an Epic trademark designating Epic parts © Epic Enterprises, March 2008
Epic Enterprises, Inc., P.O. Box 979, Southern Pines, NC 28388-0979 USATelephone Toll Free 800-648-7273 or 910-692-5441 Outside USA
Fax Toll Free 888-692-4147 or 910-692-4147 Outside USAWebsite: http://www.epicenterprises.com E-Mail: [email protected]
SI06Epic Enterprises, Inc.BMB5.TIF
EPIC MOTOR CONTROL CENTERCENTRO DE CONTROL ÉPICO DEL MOTOR
Epic Enterprises, Inc., P.O. Box 979, Southern Pines, NC 28388-0979 USATelephone Toll Free 800-648-7273 or 910-692-5441 Outside USA
Fax Toll Free 888-692-4147 or 910-692-4147 Outside USAWebsite: http://www.epicenterprises.com E-Mail: [email protected]
BACK
SI06Epic Enterprises, Inc.Position OEM Ref. Nos. Epic No. Description UOM
SI06-01 EE150400 Motor Control Center
Panel para Mando de Motor
EA
Superba is a trademark of Superba SA
Older Superbas were equipped with a very bulky Center Electric Console Unit using DC motor controllers and DC switchgear. The DC components in the Console are largely outdated and almost impossible to obtain in the event of a break-down. The old system also meant in a dual tunnel system that both tunnels had to be shut down.
The Epic Motor Control Center is much smaller and uses simplified, state-of-the-art AC variable speed motor controllers that are readily available from electric supply houses. The Epic Center controls one tunnel, thus separating two tunnel units and allowing each tunnel to operate independently. The complete Motor Control Center is Epic part number EE150400.
The control panel measures 4'x5'x 20" (100x125x500mm) and contains 3 transistor invertors as 2-1.5 HP (1KW) invertors for the prefeed and coiler units and 1-3HP (2KW) invertor for the belt drive. Also included is an M40 Programmable Controller (PLC) for interfacing the motor controls with the computer control system (Epic or Superba). The unit is complete and includes wiring, wire tray, conduit, relays, overload switches, contactors, terminal strips, etc.
The unit is furnished with wiring instructions, schematics and the PLC program. Customer must specify voltage information so that the correct voltage components may be included.
The system is almost maintenance free. Replacement electrical controls are readily available from electrical distributors. In the event that the M40 Programmable Logic Center fails or the memory is lost, Epic can supply the Logic Center or can reprogram it either by return to Epic or by modem.
Epic products are intended as replacements for worn or damaged parts in OEM products. OEM Part numbers in (parenthesis) indicate either 1) Improved design 2) the part serves the same function as the OEM part, but may differ from the OEM design, or 3) it is a component of an assembly where no OEM reference number is available, or 4) it is a repair service for the referenced OEM part.
EE is an Epic trademark designating Epic parts © Epic Enterprises, March 2008
Epic Enterprises, Inc., P.O. Box 979, Southern Pines, NC 28388-0979 USATelephone Toll Free 800-648-7273 or 910-692-5441 Outside USA
Fax Toll Free 888-692-4147 or 910-692-4147 Outside USAWebsite: http://www.epicenterprises.com E-Mail: [email protected]
SI07Epic Enterprises, Inc.CBS4.TIF
EPIC/SIGNAL ENTRY HEAT ZONE ASSEMBLYASAMBLEA DE LA ZONA DEL CALOR DE LA ENTRADA DE EPIC/SIGNAL
Epic Enterprises, Inc., P.O. Box 979, Southern Pines, NC 28388-0979 USATelephone Toll Free 800-648-7273 or 910-692-5441 Outside USA
Fax Toll Free 888-692-4147 or 910-692-4147 Outside USAWebsite: http://www.epicenterprises.com E-Mail: [email protected]
BACK
SI07Epic Enterprises, Inc.Position OEM Ref. Nos. Epic No. Description UOM
SI07-01 CC-ET-01-EN Heatsetting Zone Assembly Complete, Entry, 3.0 Meters (Includes 4 EE102004 Stainless Steel Roller Assemblies)
Conjunto completo de Zona entrado para Fijacion Termica con Ensambles de 4 Rodillos de Acero Inoxidable
EA
SI07-01A EE102004S Roller Assembly, Stainless Steel, (Inlet/Outlet Chamber)
Conjunto de Rodillos de Acero Inoxidable para Camera Entrada y Salida
EA731-230-084720-992-452
SI07-01B EE102004-1S Roller Assembly, Stainless Steel, (Inlet/Outlet Chamber) (Hardened Roller)
Conjunto de Rodillos de Acero Inoxidable para Camera Entrada y Salida (Enduracido)
EA(731-230-084)(720-992-452)
SI07-02 CC-ET-01-10 Steam Line (Closed)
Tuba Cerrado de Vapur
EA
SI07-03 CC-RB-06 Distributor, Recirculation Belt (Belt Support) (231-03)
Sopurte/Distribuidor para Correa
EA
SI07-04 260-13 Tunnel Gasket
Guarnicion para Tunel
EA
SI07-05 CC-ET-01-13 Bolt, Handway
Tornillo para Puerta de Mano
EA
SI07-06 260-09 Pipe Flange Gasket 8"
Guarnicion, 8"
EA
SI07-07 CC-ET-01-05 Shield, Tunnel, (Hood Cap) for Superba
Proteccion para Tunel
EA231-01
SI07-08 CC-ET-01-09 Steam Line (Sparge)
Tubo para Rociadura de Vapor
EA
SI07-09 CC-ET-01-12 Nut, Tunnel
Tuerca para Tunel
EA
SI07-10 CC-ET-01-11 Bolt, Tunnel
Tornillo para Tunel
EA
SI07-11 CC-ET-01-14 Nut, Handway
Tuerca para Puerta de Mano
EA
SI07-12 CC-RB-13-02 Nozzle, Recirculation Inlet (231-05)
Lanza Entrada de Recirculacion
EA
Epic Enterprises, Inc., P.O. Box 979, Southern Pines, NC 28388-0979 USATelephone Toll Free 800-648-7273 or 910-692-5441 Outside USA
Fax Toll Free 888-692-4147 or 910-692-4147 Outside USAWebsite: http://www.epicenterprises.com E-Mail: [email protected]
SI07Epic Enterprises, Inc.SI07-13 CC-RB-06-06 Recirculation Transition Piece (231-04)
Pieza de Transicion Reirculatorio
EA
SI07-14 CC-ET-01-04 Cover, Coil
Cubierta para Rollo
EA
Superba is a trademark of Superba SA
Epic products are intended as replacements for worn or damaged parts in OEM products. OEM Part numbers in (parenthesis) indicate either 1) Improved design 2) the part serves the same function as the OEM part, but may differ from the OEM design, or 3) it is a component of an assembly where no OEM reference number is available, or 4) it is a repair service for the referenced OEM part.
EE is an Epic trademark designating Epic parts © Epic Enterprises, March 2008
Epic Enterprises, Inc., P.O. Box 979, Southern Pines, NC 28388-0979 USATelephone Toll Free 800-648-7273 or 910-692-5441 Outside USA
Fax Toll Free 888-692-4147 or 910-692-4147 Outside USAWebsite: http://www.epicenterprises.com E-Mail: [email protected]
SI07AEpic Enterprises, Inc.CBS3.TIF
EPIC/SIGNAL INTERMEDIATE HEAT ZONE ASSEMBLYASAMBLEA INTERMEDIA DE LA ZONA DEL CALOR DE EPIC/SIGNAL
Epic Enterprises, Inc., P.O. Box 979, Southern Pines, NC 28388-0979 USATelephone Toll Free 800-648-7273 or 910-692-5441 Outside USA
Fax Toll Free 888-692-4147 or 910-692-4147 Outside USAWebsite: http://www.epicenterprises.com E-Mail: [email protected]
BACK
SI07AEpic Enterprises, Inc.Position OEM Ref. Nos. Epic No. Description UOM
SI07A-01 CC-ET-01-IM Heatsetting Zone Assembly Complete, Intermediate, 3.0 Meters (Includes 4 EE102004 Stainless Steel Roller Assemblies)
Conjunto completo de Zona para Fijacion Termica Con Ensambles de 4 Rodillos De Acero Inoxidable
EA
SI07A-02 CC-ET-01-10 Steam Line (Closed)
Tuba Cerrado de Vapur
EA
SI07A-03 CC-ET-01-06 Support, Belt (without Epic Rollers)
Sopurte de Correa-no Rodillos
EA
SI07A-04 260-13 Tunnel Gasket
Guarnicion para Tunel
EA
SI07A-05 CC-ET-01-05 Shield, Tunnel, (Hood Cap) for Superba
Proteccion para Tunel
EA231-01
SI07A-06 CC-ET-01-09 Steam Line (Sparge)
Tubo para Rociadura de Vapor
EA
SI07A-07 CC-ET-01-12 Nut, Tunnel
Tuerca para Tunel
EA
SI07A-08 CC-ET-01-11 Bolt, Tunnel
Tornillo para Tunel
EA
SI07A-09 CC-ET-01-04 Cover, Coil
Cubierta para Rollo
EA
SI07A-10 EE102004S Roller Assembly, Stainless Steel, (Inlet/Outlet Chamber)
Conjunto de Rodillos de Acero Inoxidable para Camera Entrada y Salida
EA731-230-084720-992-452
SI07A-10A EE102004-1S Roller Assembly, Stainless Steel, (Inlet/Outlet Chamber) (Hardened Roller)
Conjunto de Rodillos de Acero Inoxidable para Camera Entrada y Salida (Enduracido)
EA(731-230-084)(720-992-452)
Superba is a trademark of Superba SA
Epic products are intended as replacements for worn or damaged parts in OEM products. OEM Part numbers in (parenthesis) indicate either 1) Improved design 2) the part serves the same function as the OEM part, but may differ from the OEM design, or 3) it is a component of an assembly where no OEM reference number is available, or 4) it is a repair service for the referenced OEM part.
EE is an Epic trademark designating Epic parts © Epic Enterprises, March 2008
Epic Enterprises, Inc., P.O. Box 979, Southern Pines, NC 28388-0979 USATelephone Toll Free 800-648-7273 or 910-692-5441 Outside USA
Fax Toll Free 888-692-4147 or 910-692-4147 Outside USAWebsite: http://www.epicenterprises.com E-Mail: [email protected]
SI07BEpic Enterprises, Inc.CBS5.TIF
EPIC/SIGNAL EXIT HEAT ZONE ASSEMBLYASAMBLEA DE LA ZONA DEL CALOR DE LA SALIDA DE EPIC/SIGNAL
Epic Enterprises, Inc., P.O. Box 979, Southern Pines, NC 28388-0979 USATelephone Toll Free 800-648-7273 or 910-692-5441 Outside USA
Fax Toll Free 888-692-4147 or 910-692-4147 Outside USAWebsite: http://www.epicenterprises.com E-Mail: [email protected]
BACK
SI07BEpic Enterprises, Inc.Position OEM Ref. Nos. Epic No. Description UOM
SI07B-01 CC-ET-01-EX Heatsetting Zone Assembly Complete, Exit, 3.0 Meters (Includes 4 EE102004 Stainless Steel Rollr Assemblies)
Conjunto Completo de Zona Solida para Fijacion Termica con Ensamble de 4 Rodillos de Acero Inoxidable
EA
SI07B-02 CC-ET-01-10 Steam Line (Closed)
Tuba Cerrado de Vapur
EA
SI07B-03 260-13 Tunnel Gasket
Guarnicion para Tunel
EA
SI07B-04 260-09 Pipe Flange Gasket 8"
Guarnicion, 8"
EA
SI07B-05 CC-ET-01-13 Bolt, Handway
Tornillo para Puerta de Mano
EA
SI07B-06 CC-RB-13-03 Nozzle, Exit Recirculation (231-06)
Lanza Salida de Recirculacion
EA
SI07B-07 CC-ET-01-05 Shield, Tunnel, (Hood Cap) for Superba
Proteccion para Tunel
EA231-01
SI07B-08 CC-ET-01-09 Steam Line (Sparge)
Tubo para Rociadura de Vapor
EA
SI07B-09 CC-ET-01-12 Nut, Tunnel
Tuerca para Tunel
EA
SI07B-10 CC-ET-01-11 Bolt, Tunnel
Tornillo para Tunel
EA
SI07B-11 CC-ET-01-14 Nut, Handway
Tuerca para Puerta de Mano
EA
SI07B-12 CC-ET-01-04 Cover, Coil
Cubierta para Rollo
EA
SI07B-13 EE102004S Roller Assembly, Stainless Steel, (Inlet/Outlet Chamber)
Conjunto de Rodillos de Acero Inoxidable para Camera Entrada y Salida
EA731-230-084720-992-452
SI07B-13A EE102004-1S Roller Assembly, Stainless Steel, (Inlet/Outlet Chamber) (Hardened Roller)
Conjunto de Rodillos de Acero Inoxidable para Camera Entrada y Salida (Enduracido)
EA(731-230-084)(720-992-452)
Epic Enterprises, Inc., P.O. Box 979, Southern Pines, NC 28388-0979 USATelephone Toll Free 800-648-7273 or 910-692-5441 Outside USA
Fax Toll Free 888-692-4147 or 910-692-4147 Outside USAWebsite: http://www.epicenterprises.com E-Mail: [email protected]
SI07BEpic Enterprises, Inc.
Superba is a trademark of Superba SA
Epic products are intended as replacements for worn or damaged parts in OEM products. OEM Part numbers in (parenthesis) indicate either 1) Improved design 2) the part serves the same function as the OEM part, but may differ from the OEM design, or 3) it is a component of an assembly where no OEM reference number is available, or 4) it is a repair service for the referenced OEM part.
EE is an Epic trademark designating Epic parts © Epic Enterprises, March 2008
Epic Enterprises, Inc., P.O. Box 979, Southern Pines, NC 28388-0979 USATelephone Toll Free 800-648-7273 or 910-692-5441 Outside USA
Fax Toll Free 888-692-4147 or 910-692-4147 Outside USAWebsite: http://www.epicenterprises.com E-Mail: [email protected]
SI08Epic Enterprises, Inc.CBS2.TIF
EPIC/SIGNAL RECIRCULATOR BLOWER ASSEMBLYFOR SUPERBA-TYPE HEATSET LINES
MONTAJE DEL VENTILADOR DEL RECIRCULATOR DE EPIC/SIGNAL
Epic Enterprises, Inc., P.O. Box 979, Southern Pines, NC 28388-0979 USATelephone Toll Free 800-648-7273 or 910-692-5441 Outside USA
Fax Toll Free 888-692-4147 or 910-692-4147 Outside USAWebsite: http://www.epicenterprises.com E-Mail: [email protected]
BACK
SI08Epic Enterprises, Inc.
Position OEM Ref. Nos. Epic No. Description UOM
CC-RB17-6 CBS Recirculating Blower Assembly Complete, 6 Meter, with 16" (406mm) Blower Fan
Conjunto completo de Ventilador CBS, 6 Mete, con 16" Ventilador
EA
CC-RB17-9 CBS Recirculating Blower Assembly Complete, 9 Meter, with 16" (406mm) Blower Fan
Conjunto Completo de ventilador CBS, 6 Meter, con 16" Ventilador
EA
SI08-01 217-01 Shaft, Turbine Drive
Eje para Turbina
EA30-042
SI08-02 217-02 Bearing Housing
Coja para Rodiamento de Bolas
EA30-043
SI08-03 217-06 Plug, Brass Vented, (3/8" NPT Parker #219P-6)
Tapon de Laton con Paso (3/8" NPT Parker #219P-6)
EA
SI08-04 217-07 Screw, Hex Head Cap, 3/8-16 X 1 3/4"
Tornillo Hexagonal, 3/8-16 X 1 3/4"
EA
SI08-05 218-01 Main Housing Assembly
Conjunto de Caja Primera
EA
SI08-06 218-02 Removable Housing Side Wall
Protectador Lado
EA
SI08-07 218-03 Airstream Profiler
Deflexidor de Aire
EA
SI08-08 218-04 Housing Gasket
Anillo de Guarnicion
EA
SI08-09 218-05 Housing Bolt (16 Required)
Tornillo para Caja (16 requeridos)
EA
SI08-10 218-06 Bolt (4 Required)
Tornillo
EA
SI08-11 218-07 Profiler Mounting Bolts
Tornillo para Deflexidor
EA213-02
SI08-12 219-01A Pulley, Motor
Polea para Motor
EA
Epic Enterprises, Inc., P.O. Box 979, Southern Pines, NC 28388-0979 USATelephone Toll Free 800-648-7273 or 910-692-5441 Outside USA
Fax Toll Free 888-692-4147 or 910-692-4147 Outside USAWebsite: http://www.epicenterprises.com E-Mail: [email protected]
SI08Epic Enterprises, Inc.SI08-13 219-01B Bushing, Motor
Buje para Motor
EA
SI08-14 219-02 Timing Belt
Cinta del Tiempo
EA
SI08-15 219-03A Turbine Shaft Pulley
Polea para Eje de Turbina
EA30-060
SI08-16 219-04 Motor for CBS Unit
Motor para CBS
EA
SI08-17 220-01 Main Base Assembly for CBS Unit CALL EPIC FOR PRICING
Conjunto de Caja para CBSEPOPEYA DE LA LLAMADA PARA TASAR
EA
SI08-18 220-02 Motor Mounting Pivot Shaft
Eje para Montage de Motor
EA
SI08-19 220-03 Motor Adj. Pivot Shaft
Eje de Ajuste
EA
SI08-20 220-04 Adjustment Pivot Shaft Set Collar (2 Required)
Collarin para Eje de Ajuste
EA
SI08-21 220-05 Motor Adjustment Pivot Shaft Set Collar (4 Required)
Collarin para Eje de Adjuste de Motor
EA
SI08-22 220-06 Motor Adjustment Bolt
Tornillo para Ajuste de Motor
EA
SI08-23 220-07 Motor Mounting Plate
Placa para Montage de Motor
EA
SI08-24 219-01C Key
Cuna
EA
CBS RECIRCULATING BLOWER SYSTEMS are offered for the original six meter heatset tunnel and the full nine meter heatset tunnel. These two systems are identical except in the length of the return exterior mounted hot air tube. Both fit Superba machines.
COMPLETE CBS RRECIRCULATING BLOWER ASSEMLIES ARE:
CC-RB17-6 COMPLETE 6 METER CBS WITH 16" BLOWER FANCC-RB17-9 COMPLETE 9 METER CBS WITH 16" BLOWER FAN
The fan drive motor is 220/440V. The system is supplied with installation and operating instructions. CBS entry and exit manifolds are included with the system. Manifolds must be installed in tunnels by a certified ASME shop. Epic/Signal can arrange installation of manifolds. Please call for details.
Epic Enterprises, Inc., P.O. Box 979, Southern Pines, NC 28388-0979 USATelephone Toll Free 800-648-7273 or 910-692-5441 Outside USA
Fax Toll Free 888-692-4147 or 910-692-4147 Outside USAWebsite: http://www.epicenterprises.com E-Mail: [email protected]
SI08Epic Enterprises, Inc.
Superba is a trademark of Superba SA
The system takes the hot air from the exit heatsetting zone, where air temperature would be the highest, via the 16" (406mm) fan and returns it to the entry heatsetting zone. As the hot air re-enters the entry heating zone, it is forced upward through a stainless air distribution tray and through the yarn being carried on the transport belt. The effect is that the yarn receives full and near uniform heatset temperature for the entire length of the heatset tunnel. The system allows the plant to run a greater yarn mass on the belt at higher speeds to increase productivity.
Epic products are intended as replacements for worn or damaged parts in OEM products. OEM Part numbers in (parenthesis) indicate either 1) Improved design 2) the part serves the same function as the OEM part, but may differ from the OEM design, or 3) it is a component of an assembly where no OEM reference number is available, or 4) it is a repair service for the referenced OEM part.
EE is an Epic trademark designating Epic parts © Epic Enterprises, March 2008
Epic Enterprises, Inc., P.O. Box 979, Southern Pines, NC 28388-0979 USATelephone Toll Free 800-648-7273 or 910-692-5441 Outside USA
Fax Toll Free 888-692-4147 or 910-692-4147 Outside USAWebsite: http://www.epicenterprises.com E-Mail: [email protected]
SI08AEpic Enterprises, Inc.CBS1.TIF
EXPLODED VIEW OF PARTS FOR 212-00 TURBINE FAN & SHAFT ASSEMBLYFOR CBS RECIRCULATED BLOWER ASSEMBLY
VISTA DETALLADA DE LAS PIEZAS PARA EL VENTILADOR DE LA TURBINA 212-00 Y LA
Epic Enterprises, Inc., P.O. Box 979, Southern Pines, NC 28388-0979 USATelephone Toll Free 800-648-7273 or 910-692-5441 Outside USA
Fax Toll Free 888-692-4147 or 910-692-4147 Outside USAWebsite: http://www.epicenterprises.com E-Mail: [email protected]
BACK
SI08AEpic Enterprises, Inc.
Position OEM Ref. Nos. Epic No. Description UOM
SI08A-02 212-01 Pin, Stainless Steel Cotter, 1/8" X 1 1/2" Long
Perno de Careta, Azero Inoxidable, 1/8" X 1 1/2" Largo
EA30-027
SI08A-03 212-02 Washer, Flat, 5/8"
Arandela Plana, 5/8"
EA30-028Not Applicable
SI08A-04 212-03 Nut, Brass Castle, 5/8"
Tuerca de Laton, 5/8"
EA30-029
SI08A-05 212-04 Bushing, Turbine
Buje para Turbina
EA30-030A
SI08A-06 212-05 Blade, Turbine, 16" (Note: Turbine Bushing is included with Blade)
16" Paleta de Turbina con Buje
EA30-030
SI08A-07 212-06 Key, Turbine Bushing, 3/16" X 3/16 " X 1"
Cuna, 3/16" X 3/16" X 1"
EA30-031
SI08A-08 212-07 Screw, Socket Head Cap, 10/32" X 3/4"
Tornillo Cilindrico, 10/32" X 3/4"
EA
SI08A-09 213-01 Box, Fluid Guide
Caja de Guia Fluida
EA
SI08A-10 213-02 Screw, Flat Head Cap, 1/4-20 X 1" Long
Tornillos para Montage, 1/4-20 X 1" Largo
EA
SI08A-11 214-01 Housing, Packing
Caja para Empoque dura
EA
SI08A-12 214-02 Bushing, Brass Housing
Buje de Laton para Caja de Empaquedura
EA30-036
SI08A-13 214-03C Packing Material, 5/16" Square X 25" Long, Graphite
Empaquerdura, 5/16" X 25" Largo
EA30-037
SI08A-14 214-04 Insert, Brass Housing
Insercion de Laton para Caja
EA30-038
SI08A-15 214-05 Bolt, Insert Mounting, 3/8-16 SS Stud X 2-1/8" with Nut
Perno y Tuerca para Montage, 3/8-16 SS Stud X 2-1/8"
EA
Epic Enterprises, Inc., P.O. Box 979, Southern Pines, NC 28388-0979 USATelephone Toll Free 800-648-7273 or 910-692-5441 Outside USA
Fax Toll Free 888-692-4147 or 910-692-4147 Outside USAWebsite: http://www.epicenterprises.com E-Mail: [email protected]
SI08AEpic Enterprises, Inc.SI08A-16 214-06 O-Ring, Housing, 242 Silicone 4-1/4" OD
X 4" ID
Anillo "O", 242 Silicone 4-1/4" OD X 4" ID
EA30-040
SI08A-17 214-07 Heat Deflector
Deflexidor de Calor
EA
SI08A-18 217-01 Shaft, Turbine Drive
Eje para Turbina
EA30-042
SI08A-19 217-02 Bearing Housing
Coja para Rodiamento de Bolas
EA30-043
SI08A-20 217-03 Bearing, Shaft, NTN#6206NSL
Rodamiento de Bolas, NTN#6206NSL
EA
SI08A-21 217-04 Ring, Inside Snap (#5000-237)
Retenador Internal (#5000-237)
EA
SI08A-22 217-05 Ring, Outside Snap (#5100-118)
Retenador External (#5100-118)
EA
SI08A-23 217-06 Plug, Brass Vented, (3/8" NPT Parker #219P-6)
Tapon de Laton con Paso (3/8" NPT Parker #219P-6)
EA
SI08A-24 217-07 Screw, Hex Head Cap, 3/8-16 X 1 3/4"
Tornillo Hexagonal, 3/8-16 X 1 3/4"
EA
SI08A-25 218-02 Removable Housing Side Wall
Protectador Lado
EA
SI08A-26 218-04 Housing Gasket
Anillo de Guarnicion
EA
SI08A-27 219-03A Turbine Shaft Pulley
Polea para Eje de Turbina
EA30-060
SI08A-28 219-03B Turbine Shaft Bushing
Buje para Eje de Turbina
EA
SI08A-29 219-03C Key
Cuna
EA
Superba is a trademark of Superba SA
Epic products are intended as replacements for worn or damaged parts in OEM products. OEM Part numbers in (parenthesis) indicate either 1) Improved design 2) the part serves the same function as the OEM part, but may differ from the OEM design, or 3) it is a component of an assembly where no OEM reference number is available, or 4) it is a repair service for the referenced OEM part.
EE is an Epic trademark designating Epic parts © Epic Enterprises, March 2008
Epic Enterprises, Inc., P.O. Box 979, Southern Pines, NC 28388-0979 USATelephone Toll Free 800-648-7273 or 910-692-5441 Outside USA
Fax Toll Free 888-692-4147 or 910-692-4147 Outside USAWebsite: http://www.epicenterprises.com E-Mail: [email protected]
SI11Epic Enterprises, Inc.SI11.TIF
SPARE PARTS FOR SIGNAL OPTIBULK & OPTIBULK EZPREBULKING SYSTEM FOR SUPERBA-TYPE HEATSET
PIEZAS DE REPUESTO PARA LA SEÑAL OPTIBULK Y OPTIBULK EZ
Epic Enterprises, Inc., P.O. Box 979, Southern Pines, NC 28388-0979 USATelephone Toll Free 800-648-7273 or 910-692-5441 Outside USA
Fax Toll Free 888-692-4147 or 910-692-4147 Outside USAWebsite: http://www.epicenterprises.com E-Mail: [email protected]
BACK
SI11Epic Enterprises, Inc.
Position OEM Ref. Nos. Epic No. Description UOM
SI11-01 YS-09-R2 Shaft, Fan 14-3/4" Long (New Optibulk)
Ejerde Ventilador para Optibulk (Nuevo)
EA
SI11-02 YS-09-R1 Shaft, Fan x 12-3/4" Long (Old Optibulk & EZ)
Eje de Ventilador para optibulky EZ (Viejo), 12-3/4" Long
EA
SI11-02A YS-09-R3 Shaft, Fan 13 1/2" (EZ Conversion)
Ejerde Ventilador, 13 1/2"
EA30-250
SI11-03 YS-06-S10 Support, Yarn Belt
Soporte de Correa para Hilo
EA
SI11-04 YS-03-07 Rubber, Silicone (1" x 3/8 Wide)
Empaqueta dura de Goma-Silicona
EA30-007
SI11-06 YS-03-05 Blade, Fan
Hoja para Ventilador
EA30-005
SI11-07 YS-03-04 Seal, Fan Shaft Steam
Anillo de selladura para Eje de Ventilador
EA30-004
SI11-08 YS-03-03 Bearing, Fan Shaft (2 per Cabinet)
rodamiento de Bolas para Eje de Ventilador
EA
SI11-09 YS-03-02 Coupling, Fan Shaft
Acopladura para Eje de Ventilador
EA30-002
SI11-10 YS-03-01 Motor, Fan
Motor para Ventilador
EA
SI11-11 YS-01-31 Probe, Temperature, 6 Inch
Tienta para Tempeatura, 6 Inch
EA
SI11-12 YS-01-21 Probe, Temperature, 12 Inch
Tienta para Temperatura, 12 inch
EA
SI11-13 OPT-E-251 Cylinder, Front
Cilindro Frente
EA
SI11-14 OPT-E-242 Cylinder, Side
Cilindro Lado
EA
SI11-15 ET-4 Motor & Fan Mount Cabinet
Gabinete para Motory Montage de Ventilador
EA
Signal originally produced the OptiBulk Prebulker and an upgrade of the Superba prebulker known as EX Top or EZ Conversion. Recent installations now use the more efficient Epic Prebulker (see section on Epic Prebulker).
Epic Enterprises, Inc., P.O. Box 979, Southern Pines, NC 28388-0979 USATelephone Toll Free 800-648-7273 or 910-692-5441 Outside USA
Fax Toll Free 888-692-4147 or 910-692-4147 Outside USAWebsite: http://www.epicenterprises.com E-Mail: [email protected]
SI11Epic Enterprises, Inc.
Superba is a trademark of Superba SA
Because many of the original Signal Prebulkers are in service, Epic offers the spare parts for Optibulk and EZ Top or EZ Conversion.
Epic products are intended as replacements for worn or damaged parts in OEM products. OEM Part numbers in (parenthesis) indicate either 1) Improved design 2) the part serves the same function as the OEM part, but may differ from the OEM design, or 3) it is a component of an assembly where no OEM reference number is available, or 4) it is a repair service for the referenced OEM part.
EE is an Epic trademark designating Epic parts © Epic Enterprises, March 2008
Epic Enterprises, Inc., P.O. Box 979, Southern Pines, NC 28388-0979 USATelephone Toll Free 800-648-7273 or 910-692-5441 Outside USA
Fax Toll Free 888-692-4147 or 910-692-4147 Outside USAWebsite: http://www.epicenterprises.com E-Mail: [email protected]