TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - -1 5/20/13 EFF - ALL
FIRE PROTECTION ATA 26
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 0 5/20/13 EFF - ALL
THIS PAGE INTENTIANLLY LEFT BLANK
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 1 5/20/13 EFF - ALL
ATA 26 FIRE PROTECTION
TABLE OF CONTENTS......................................................................... 1
FIRE PROTECTION - INTRODUCTION ............................................... 2
FIRE PROTECTION - OPERATIONAL TEST ....................................... 4
FIRE DETECTION SYSTEM ................................................................. 6
ENGINE/FIRE OVERHEAT DETECTION TEST FIRE.......................... 8
ENGINE FIRE OVRHEAT DETECTION - INTRO ............................... 12
GENERAL DESCRIPTION.................................................................. 14
MAIN DECK CARGO SMOKE DETECTION SYSTEM - GEN DESC . 26
FREIGHTER LAV SMOKE DETECTION GENERAL DESC ............... 28
APU FIRE DETECTION - INTRODUCTION & LOCATION................. 36
GENERAL DESCRIPTION.................................................................. 38
APU FIRE DETECTION - INDICATIONS ............................................ 44
LWR CARGO COMP SMOKE DETECTION - INTRODUCTION......... 48
LWR CARGO COMP- SMOKE DET - FUNCTIONAL DESCRIPTION 56
AFOLTS CARD - FUNCTIONAL DESCRIPTION - DUAL LOOP ........ 62
WHEEL WELL FIRE DETECTION - INTRODUCTION ....................... 64
WING AND BODY DUCT LEAK DETECTION & INTRODUCTION .... 70
STRUT OVERHEAT DETECTORS - FUNCTIONAL DESCRIPTION . 76
ENGINE FIRE EXTINGUISHING - COMPONENT LOCATIONS ........ 80
APU FIRE EXTINGUISHING - INTRODUCTION ................................ 96
LOWER CARGO FIRE EXTINGUISHING - INTRODUCTION .......... 106
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 2 5/20/13 EFF - ALL
FIRE PROTECTION - INTRODUCTION
Purpose
The fire protection systems monitor the airplane for these conditions:
• Fire • Smoke • Engine overheat • Pneumatic duct leak • Strut leak detection
The fire protection systems also include fire extinguishers.
Fire/Overheat Detection
The airplane has these fire/overheat detection systems:
• Engine fire detection • Engine overheat detection • APU fire detection • Cargo compartment smoke detection • Wheel Well fire detection • Duct leak detection • Lavatory smoke detection • Electrical and electronic (E/E) cooling smoke detection
Extinguishing
• The airplane has these fire extinguishing systems: • Engine • APU • Cargo compartment • Lavatory • Portable fire extinguishers
Abbreviations and Acronyms
A/G - air ground systemAFOLTS - automatic fire overheat logic test system
APU - auxiliary power unitAPUC - auxiliary power unit controllerARINC - Aeronautical Radio, Inc.auto - automaticBIT - built-in-testBITE - built-in-test-equipmentbtl - bottlebtls - bottlescgo - cargoch - channeldisch - dischargeDLODS - duct leak and overheat detection systemECS - environmental control systemEDP - engine-driven pumpEEC - electronic engine controllerEICAS - engine indication and crew alerting systemENG - engineequip - equipmentext - extinguishingfwd - forwardind - indicatorkg - kilogramLED - light emitting diodeLRU - line replaceable unitMD&T - master dim and testMEC - main equipment centerovht - overheatovrd - overridepress - pressurePSEU - proximity switch electronics unitpwr - powerrmt - remotestby - standbyvlv - valveWEU - warning electronics unitWOW - weight-on-wheels
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 3 5/20/13 EFF - ALL
FIRE PROTECTION - INTRODUCTION
- FIRE/SMOKE - OVHT - FIRE
SYSTEMWHEEL WELL
- EXTINGUISHING
LAVATORY
- EXTINGUISHING
DUCT LEAKSYSTEM - FIRE
CARGO SYSTEMS
- EXTINGUISHING - FIREAPU SYSTEM
- EXTINGUISHING - OVHT - FIREENGINE SYSTEMS
PROTECTIONFIRE/OVHT
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 4 5/20/13 EFF - ALL
FIRE DETECTION SYSTEMEngine Fire
The left and right engine systems are identical. Each engine has a dual loop detector system. The engine fire loops are broken into three separate elements; the engine accessory area, the upper turbine area, and the lower turbine area. These detector loops send signals of a fire or fault condition to its interchangeable dedicated detector card. These detector cards are located in the P54 fire detection card file in the main equipment center. The detector cards discriminate between fire and fault conditions and send that message to the automatic fire/overheat logic/test system card (AFOLTS card) also located in the P54 file. If the programmed logic in AFOLTS is satisfied (AND logic when configured in dual loop), the AFOLTS card alerts the flight crew. Some of the flight compartment outputs are shown.
Engine Overheat
The overheat system is a very similar system to the engine fire system. The major differences are that only one segment is located on the engine, at the pneumatic ducting area, and that an overheat is a caution not a warning. AFOLTS card No. 1 is shared by left engine fire and left engine overheat, while the right engine uses AFOLTS card No. 2. All AFOLTS cards are interchangeable.
APU Fire
The APU dual detector loop system protects against APU compartment fires. There are two segments, one located above the APU on the air intake and one located below the APU on the clam shell door. The loops feed their detector cards (identical to the engine detector cards). The APU detector cards feed AFOLTS card No. 3. The flight compartment outputs are shown.
Wheel Well Fire and Duct Leak Detection
A single loop wheel well fire system is wired in series through both wheel wells into one detection segment. The Fenwal built system feeds the wheel well fire/duct leak detection card. This unique card is also in the P54 card file. Outputs from this card feed the wheel well fire indicators in the flight compartment. A wheel well fire is a warning alert. The three duct leak zones; left wing, right wing, and body, also feed the wheel well fire/duct leak detection card.
Cargo Smoke Detection System
The forward and aft cargo compartments contain two smoke detectors in each compartment. When a preset level of smoke is detected by both detectors(AND logic), the number six AFOLTS card outputs a cargo fire signal. The smoke detectors use a vacuum system to generate a blow through sample of compartment air for increased reliability.
Testing
The ENG/APU/CARGO test switch on the test panel sends an input to all AFOLTS cards to run a circuit check of the detector cards and a continuity check of the loops that feed them. If the cards and loops are working correctly, the AFOLTS cards will output fire and overheat signals to the flight compartment. If one loop fails, the test is still successful but the bad loop is annunciated on EICAS. If both loops fail, the test is unsuccessful and the test panel fail light illuminates. The wheel well test switch runs a continuity check of the wheel well detector loop. The duct leak continuity test is initiated at the P61 duct leak panel. If the duct leak lights illuminate, the system is continuous.
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 5 5/20/13 EFF - ALL
FIRE DETECTION SYSTEM
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 6 5/20/13 EFF - ALL
ENGINE FIRE OVERHEAT DETECTION - GENERAL DESCRIP-TION
General
Each engine has two fire detection loops. A fire detection card in the system card file monitors the loops for fires, overheat conditions, and faults. There is a fire detection card for each engine.
Overheat Detection
If the fire detection loops find an overheat condition, the fire detection card sends a signal to the AFOLTS card and to the warning electronics unit. The AFOLTS card sends a caution message and turns on the master caution light.
The warning electronics unit turns on the master caution light and overheat aural warning.
When the overheat condition goes away, the indications go away.
Fire Detection
If there is an engine fire, the detection loop sends a signal to the fire detection card. The detection card sends a signal to the AFOLTS card. The AFOLTS card sends signals to the warning electronics unit and to flight deck indications.
When the fire is out, the indications go away.
Continuous Fault Monitoring
The fire detection card monitors the two loops and the wiring for defects. In normal (dual loop) operation, both loops must have a fire or overheat to cause the flight deck indications.
If a failure occurs in a loop, the fire detection card sends the data to AFOLTS. A status message shows. The system changes to single loop operation with the FIRE/OVHT TEST switch on the P8 panel. In this mode, fire and overheat indications occur when one loop is defective and the other has a fire or overheat condition.
System Tests
Use the FIRE/OVERHEAT test switch on the P8 panel to do a test of the system. Test indications are the same as the actual fire and overheat warning indications.
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 7 5/20/13 EFF - ALL
ENGINE FIRE OVERHEAT DETECTION - GENERAL DESCRIPTION
FIRE LIGHT
FIRE
LEFT
1 2DISCH
1 2DISCH
THGIR
R ENGOVHT2 DISCH
ENG BTL1 DISCH
ENG BTLOVHTL ENG
ENGINE FIRE CONTROL PANEL
FIRE TEST PANEL
FAIL
ENG/APU
FIRE/OVHT TEST
CARGOWELLWHL SYS FAIL
P-RESET
CIRCUITSAND TESTINDICATIONSAND FAULTFIRE, OVHT
CARD 2AFOLTS
CARD LOOP 2R OVHT DET
P54 FIRE DET CARD FILE
CARD LOOP 1R OVHT DET
CARD LOOP 2R FIRE DET
CARD LOOP 1R FIRE DET
DET LOOP 2R NACELLE OVHT
DET LOOP 1R NACELLE OVHT
DET LOOP 2R ENGINE FIRE
DET LOOP 1R ENGINE FIRE
CARD 1AFOLTS
CARD LOOP 1L FIRE DET
CARD LOOP 2L FIRE DET
CARD LOOP 1L OVHT DET
CARD LOOP 2L OVHT DET
DET LOOP 1L ENGINE FIRE
DET LOOP 2L ENGINE FIRE
DET LOOP 1L NACELLE OVHT
DET LOOP 2L NACELLE OVHT
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 8 5/20/13 EFF - ALL
ENGINE FIRE OVERHEAT DETECTION - INTRODUCTION
Purpose
The engine fire/overheat detection system has these functions:
• Gives warnings in the flight compartment if there is a fire in an engine nacelle
• Gives caution indications in the flight compartment if an engine has an overheat condition
• Does tests on the system • Changes system operation in relation to pass/fail status of detector loops • Gives flight compartment messages for system condition
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 9 5/20/13 EFF - ALL
ENGINE FIRE OVERHEAT DETECTION - INTRODUCTION
DUAL LOOP ENGINE FIREAND OVERHEAT DETECTORS
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 10 5/20/13 EFF - ALL
FLIGHT DECK INDICATIONS - INTRODUCTIONS
Functional Description
A fire in the engine will display the following indications:
• Discrete warning display • Master warning light • Fuel control switch • Engine fire handle • Fire bell • EICAS warning message
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 11 5/20/13 EFF - ALL
FLIGHT DECK INDICATIONS - INTRODUCTIONS
LEFT
1 2DISCH
1 2DISCH
THG IR
R ENGOVHT2 DISCH
ENG BTL1 DISCH
ENG BTLOVHTL ENG
FIRE CONTROL PANEL (P8)
P7
CAUTION
WARNING
(WARNING & CAUTION)
DISCRETE WARNINGDISPLAY (P1-3)
CABIN
PULL UP DISCA/P
OVSPD
CONFIGFIRE
ALT
AURAL INDICATION SPEAKERS
L ENG FIRE LP 1L ENG FIRE LP 2
L ENG FIRE
FUEL CONTROL SWITCH MODULE (P10)
P7
CAUTION
WARNING
EICAS DISPLAY UNITS (P2)
FUEL CONTROL -RL-
CUT OFF
RUN
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 12 5/20/13 EFF - ALL
ENGINE FIRE DETECTION - FIRE DETECTORS
Purpose
The engine fire/overheat detection system monitors the engine for fire or overheat conditions.
Physical Description
The engine fire/overheat detection system has these components:
• Lower forward engine detector • Lower aft engine detector • Upper aft (firewall) detector • Forward upper overheat detector
Location
The lower forward detector is below the engine fan section. The lower aft detector is below the turbine section of the engine. The upper aft (firewall) detector is above the turbine section of the engine. The overheat detector is in the strut area of the engine.
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 13 5/20/13 EFF - ALL
ENGINE FIRE DETECTION - FIRE DETECTORS
ENGINE FIRE DETECTION SENSOR(TYPICAL)
ATTACHMENTSENSOR SUPPORT TUBEELEMENT LUG
UPPER AFT ENGINEFIREWALL FIRE DETECTOR
LOWER AFTENGINE FIRE
UPPER FWD ENGINEOVERHEAT DETECTOR
DETECTORLOWER FORWARDENGINE FIRE DETECTOR
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 14 5/20/13 EFF - ALL
ENGINE FIRE DETECTORS - FUNCTIONAL DESCRIPTION
Physical Description
Two sensing elements are parallel on either side of a contoured rigid support tube. These elements have an tube with thermistor material with two embedded electrical conductors. Both ends of the tube are electrical connectors attached to the conductors with one of the conductors grounded to the shell of the connector.
Functional Description
When the overheat sensor loop gets to the trip temperature, the thermistor material in the tubing decreases in resistance and sends an overheat signal to the fire detector card.
When the LOWER FORWARD, LOWER AFT, and UPPER AFT fire detection sensors get to the trip temperatures, the thermistor material has decreased its resistance to the trip point and sends a fire signal to the fire detector card.
The fire detector sensors and overheat sensors have a discrete trip temperature for localized hot spots. The sensors reset when the temperature cools sufficiently.
The environmental temperature is provided to help determine the operating temperature and a guide to the capability of resetting the sensor.
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 15 5/20/13 EFF - ALL
ENGINE FIRE DETECTORS - FUNCTIONAL DESCRIPTIONTOLERANCE ALLOWANCE IS 50F1
TEMPERATURETEMPERATURETRIP TEMPERATURES
LOCATION
ENVIRONMENTAL
LOWER AFT 750F 650F
TOTAL LENGTH
RESET
(AVERAGE) (MAXIMUM)
750F
1100F
ONE FOOT DISCRETE(MAXIMUM) (MINIMUM)
LOWER FORWARD
UPPER AFT 800F
1050F
1150F
400F
700F
250F
500F700F
UPPER FWD (OVERHEAT) 600F 950F 500F 485F
1
ENGINE FIRE DETECTION SENSOR(TYPICAL)
UPPER AFT ENGINEFIREWALL
LOWER AFTENGINE FIRE
UPPER FWD ENGINEOVERHEAT DETECTOR
DETECTORLOWER FORWARDENGINE FIREDETECTOR
FIRE DETECTOR
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 16 5/20/13 EFF - ALL
AFOLTS CARDS - FUNCTIONAL DESCRIPTION - DUAL LOOP
General
The automatic fire and overheat logic and test system (AFOLTS) cards give indications of fire or overheat conditions when the detector cards receive alarm or fault signals from the fire or overheat detection loops. Outputs from the AFOLTS card give indications and flight compartment messages. The cards can operate in dual loop mode (normal) or single loop mode. The dual loop mode shows here.
An AFOLTS card receives alarm and fault signals from four detector cards. The detector cards connect to two fire detection loops and to two overheat detection loops.
During dual loop mode operation, an alarm or fault signal is necessary from the two detector cards to make an alarm warning of a fire or overheat condition.
EICAS
A single loop output shows as a message on the status and maintenance pages. If the two loops have an output (alarm), the EICAS display changes to a warning, and the loop messages are disabled.
Test
When the card is in the dual loop mode, it monitors loop 1 and loop 2 detector cards. If the detector card finds a fault with one or two of its loops during a power-up self-test or a manual test from the P8 panel, a fault signal goes to the AFOLTS card and the AFOLTS sends status and maintenance messages to the flight deck to show which loop has a failure. If there is a failure of one loop, the AFOLTS card ignores that loop, and the system operates in the single loop mode with different logic. If the two loops have failures, a SYS FAIL light and FIRE/OVHT SYS advisory message shows in the flight compartment.
Detector, card, or related wiring failures cannot give a valid fault output at the moment of a failure. These defective loops can only be found during a system test.
Automatic 60 Minute Test
The AFOLTS card automatically gives a self test command to the detection zones when the detection loops, fire/overheat/smoke, in a zone are in disagreement for more than five seconds, or the zone is already in the single loop mode.
The AFOLTS card gives the self test command every 60 minutes if the initial condition does not change or stays in the single loop operation.
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 17 5/20/13 EFF - ALL
AFOLTS CARDS - FUNCTIONAL DESCRIPTION - DUAL LOOP
TAKEOFF<20 SEC AFTER
<400 FEETRADIO ALTM
NOT PUSHEDMASTER WARN
WARNING ELECTRONICS UNIT (P51)
1
LOOP MSG(S&M)
LOOP MSG(S&M)
R EICAS COMPUTER
FIRE/OVHT SYS
L EICAS COMPUTER
LOOP MSG(S&M)
LOOP MSG(S&M)
FIRE/OVHT SYS
AFOLTS (TYP) (P54)
NOTE STATUS LOOP MSGS ARE INHIBITEDMAINTENANCE LOOP
:DURING AN ALARM.MSGS ARE SHOWN DURING AN ALARM.
P54
P54
FAULTALARM
FAULT
FOUND BY A FAILED TESTCIRCUIT INOPERATIVE SIGNAL AS
EXTENSION ON TAKEOFFSTARTS BY NOSE STRUT
2. FIRE SW LOCK RELEASE (P8)3. FUEL CONT SW LIGHT (P8)
1. FIRE SW LIGHTS (P8)
1. FIRE DISCRETE ANN (P1-3)
ALARM 2
ALARM 1
EICAS LOOP 2
EICAS LOOP 1
ALARM
FAULT TEST
ALARM TEST
FAULT TESTALARM TEST
CARDDETECTORLOOP 2
FIRE/OVHT TEST PANEL (P8)SEQUENCERTEST
CARDDETECTORLOOP 1
TEST SWITCH ENG/APU/CARGO
SYS FAIL LIGHT
2 2
1
2
T
T
2. FIRE WARNING BELL
1. MASTER WARNING LIGHTS (P7)
ALARM OR FAULT + NOTHING FORMORE THAN 5 SEC = TEST EVERY60 MINUTES.
SOFTWAREALARM + ALARM = ALARMALARM + FAULT = ALARM
FAULT + ALARM = ALARMFAULT + FAULT = FAIL LIGHT
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 18 5/20/13 EFF - ALL
AFOLTS CARDS - FUNCTIONAL DESCRIPTION - SINGLE LOOP
GeneralThe automatic fire/overheat logic test system (AFOLTS) can operate in either a dual loop mode or a single loop mode. The single loop mode is shown here.
The AFOLTS card can deselect a faulty detection loop after that loop has failed a test. The test may be either a self-test started when power is applied to the battery bus (or when power is interrupted for more than two milliseconds) or a manual test from the P8 panel.
After an AFOLTS card deselects a faulty loop, the fire/overheat detection system only needs a single alarm or fault signal from the remaining good loop.
If a fire or overheat condition is detected in the single loop mode, flight deck warning and indications are the same as for the dual loop mode.
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 19 5/20/13 EFF - ALL
AFOLTS CARDS - FUNCTIONAL DESCRIPTION - SINGLE LOOP
FAULT FAULT -OR-FIRE
OVHTALARM ALARM
LOOP 2LOOP 1
MAINTENANCE
AFOLTSDESELECTED BY
MODESINGLE LOOP
AFOLTSDESELECTED BY
X
X
X
X
MESSAGES
STATUS AND
INDICATION
AFOLTS CONFIG
MESSAGE SHOWN ONFIRE/OVHT SYS ADVISORYSYS FAIL LIGHT AND
MESSAGES ARE SHOW.MAINTENANCE LOOP
ARE INHIBITED DURINGSTATUS LOOP MESSAGES
AFOLTS CARD - LOGIC TABLE FOR SINGLE LOOP CONFIGURATION
AN ALARM.
1 2
X
X
X 2
X 1
X 2
X 1
FLIGHT DECK.
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 20 5/20/13 EFF - ALL
ENGINE/FIRE OVERHEAT DETECTION - INDICATIONS
Fire Indication
If there is an engine fire, these are the indications in the flight compartment:
• Fire switch light • Fire switch lock releases • Fuel control switch light • EICAS warning message, L (R) ENGINE FIRE • Discrete fire warning light • Flight compartment fire bell • Master warning lights
Overheat Indication
If an engine has an overheat, these are the indications:
• Discrete overheat annunciator light • EICAS caution message, L (R) ENG OVHT • Caution aural • Master caution lights
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 21 5/20/13 EFF - ALL
ENGINE/FIRE OVERHEAT DETECTION - INDICATIONS
LEFT
1 2DISCH
1 2DISCH
THGIR
R ENGOVHT2 DISCH
ENG BTL1 DISCH
ENG BTLOVHTL ENG
FIRE CONTROL PANEL (P8)
P7
CAUTION
WARNING
(WARNING & CAUTION)
DISCRETE WARNINGDISPLAY (P1-3)
CABIN
PULL UP DISCA/P
OVSPD
CONFIGFIRE
ALT
AURAL WARNING SPEAKERS
FUEL CONTROL SWITCH MODULE (P10)
P7
CAUTION
WARNING
EICAS DISPLAY UNITS (P2)
FUEL CONTROL RL
CUT OFF
RUN
L ENG FIREL ENG OVHT
L ENG OVHT LP 1L ENG OVHT LP 2
L ENG FIRE LP 1L ENG FIRE LP 2
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 22 5/20/13 EFF - ALL
ENGINE/FIRE OVERHEAT DETECTION - TEST FIRE
General
The fire test switch (ENG/APU/CARGO) does a test of these systems:
• Engine fire/overheat detection • APU fire detection • Cargo smoke detection
Only the engine fire detection test is shown here.
Fire Test Indications
When you push the ENG/APU/CARGO test switch, these indications come on:
• Fire switch • Fuel control switch • Discrete fire warning light • Master warning lights • Flight compartment fire bell • Flight deck warning, status, and maintenance messages
Test Initiation
The test is started with the FIRE/OVHT TEST - ENG/APU/CARGO switch on the P8 panel. The complete test takes four seconds. During this time, all the engine fire detector loops show as flight deck messages.
Fire Test Pass
When you release the switch, all test indications go away. The systems may have faults which do not prevent flight. An example is a single loop fault in the engine fire detection system. A status message shows this fault. Refer to the Dispatch Deviation Guide to see if this fault will limit flight operations.
Fire Test Fail
When you release the switch, any faulty loops show on the EICAS status and maintenance pages. If one loop of the left engine fire detection system fails, for
example, that loop is deselected and the system changes to a single loop configuration using the input from the remaining good loop. If both left engine fire detection loops fail, the SYS FAIL light on the P8 test module comes on and the EICAS advisory message, FIRE/OVHT SYS shows. Push the fail light to turn off the light and remove the EICAS advisory message.
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 23 5/20/13 EFF - ALL
ENGINE/FIRE OVERHEAT DETECTION - TEST FIRE
TAT + 12CREV
+10c
1N
EGT
825
54.2 21.3
D-TOTAI
HOT
528
109.7
826
L ENG FIRE
FIRE/OVHT SYS
ECS/MAINT
L ENG FIRE LP 1L ENG FIRE LP 21
EICAS DISPLAY UNITS(P2)
LEFT
1 2DISCH
1 2DISCH
THGIR
R ENGOVHT2 DISCH
ENG BTL1 DISCH
ENG BTLOVHTL ENG
ENGINE FIRE CONTROL PANEL (P8)
FAIL
ENG/APU
FIRE/OVHT TEST
CARGOWELLWHL
SYS FAIL
P-RESET
LOOP 1 AND 2SIGNAL 1
ALARM WARNING
SHOWS WHILE TEST SWITCH IS PUSHED
LWR FWD ENG FIRE DETLWR AFT ENG FIRE DET
TESTMANUAL
(E8)COMPUTERSL(R) EICAS
SIGNALSALARM/FAULT
FAULT SIGNALDUAL LOOP
SYSTEM
SPEAKERWARNING
CENTER QUADRANT
ALARM WARN
AURAL
LOOP 2 DET SIGLOOP 1 DET SIG
FIRE DETENG FIREWALL
1FOR LOOP TEST, LIGHT GOES OUT WHEN SWITCH IS RELEASED IF THE LOOPTEST IS SUCCESSFUL
SIGNAL 2
FIRE DETECTIONCARD FILE (P54)
WARNING ELECTRONICSUNIT (P51)
FUEL CONTROL RL
CUT OFF
RUN
AFT CONTROLSTAND (P8)
P7
WARNING
CAUTION DISCRETE WARNINGDISPLAY (P1-3)
CABIN
PULL UP DISCA/P
OVSPD
CONFIGFIRE
ALT
(P10)
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 24 5/20/13 EFF - ALL
ENGINE FIRE/OVERHEAT DETECTION - TEST OVERHEAT
General
The fire test switch (ENG/APU/CARGO) does a test of these systems:
• Engine fire/overheat detection • APU fire detection • Cargo smoke detection
Only the engine overheat detection test is shown here.
Overheat Test Indications
When you push the ENG/APU/CARGO test switch, these indications come on:
• Master caution lights • Caution aural tone • Flight deck caution, status, and maintenance messages
Test Initiation
The test is started with the FIRE/OVHT TEST - ENG/APU/CARGO switch on the P8 panel. The test takes four seconds. During this time, all the engine overheat detector loops show as flight deck messages.
Overheat Test Pass
When you release the switch, all test indications go away. The systems may have faults which do not prevent flight. An example is a single loop fault in the engine overheat detection system. A status message shows this fault. Refer to the Dispatch Deviation Guide to see if this fault will limit flight operations.
Overheat Test Fail
When you release the switch, any faulty loops show on the EICAS status and maintenance pages. If one loop of the left engine overheat detection system fails, for example, that loop is deselected and the system changes to a single loop configuration using the input from the remaining good loop. If both left engine overheat detection loops fail, the SYS FAIL light on the P8 test module
comes on and the EICAS advisory message, FIRE/OVHT SYS shows. Push the fail light to turn off the light and remove the EICAS advisory message.
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 25 5/20/13 EFF - ALL
ENGINE FIRE/OVERHEAT DETECTION - TEST OVERHEAT
EICAS DISPLAY UNITS (P2)
ECS/MAINT
L ENG OVHT LP 1L ENG OVHT LP 21
(E8)
L (R) EICASCOMPUTERS
LEFT
1 2DISCH
1 2DISCH
THGIR
R ENGOVHT2 DISCH
ENG BTL1 DISCH
ENG BTLOVHTL ENG
ENGINE FIRE CONTROL PANEL (P8)FAIL
ENG/APU
FIRE/OVHT TEST
CARGOWELLWHL
SYS FAIL
P-RESET
AFT CONTROL
UPPER FWD ENGOVHT DET
LOOP 1 DETECTORLOOP 2 DETECTOR
FIRE DETECTIONCARD FILE (P54)
WARNINGELECTRONICS
P7
SYSTEM MANUALTEST
ALARM SIGNAL
AURAL WARNSPEAKERS(CAUTION)
LOOP 1 & 2ALARM/FAULTSIGNALS
1 SHOWS WHILE TEST SWITCH IS PUSHED DURINGLOOP TEST, REMOVED WHEN SWITCH IS RELEASEDIF THE LOOP TEST IS SUCCESSFUL
STAND (P8)
DUAL LOOP FAULT SIGNAL
UNIT (P51)
WARNING
CAUTION
TAT + 12CREV
+10c
1N
EGT
825
54.2 21.3
D-TOTAI
HOT
528
109.7
826
L ENG FIRE
FIRE/OVHT SYS
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 26 5/20/13 EFF - ALL
ENGINE FIRE EXTINGUISHING - INTRODUCTION
Purpose
The engine fire extinguishing system extinguishes fires in the engine nacelles.
General Description
The two fire extinguishing bottles contain halon fire extinguishing agent pressurized with nitrogen. You use the engine fire switches in the flight deck to release the halon. Halon from each bottle can go to the left or right engine. EICAS messages, status messages, and indicator lights show when the bottle pressure is low.
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 27 5/20/13 EFF - ALL
ENGINE FIRE EXTINGUISHING - INTRODUCTION
TUBEDISTRIBUTION
COMPARTMENTFWD CARGO
21
FIRE CONTROL PANEL (P8)
ENG BTL1 DISCHENG BTL
LEF
1 2DISCH
T
1 2DISCH
THGIR
2 DISCH
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 28 5/20/13 EFF - ALL
ENGINE FIRE EXTINGUISHING - COMPONENT LOCATIONS
Purpose
The engine fire extinguishing system extinguishes fires in the engine nacelles.
General Description
The two fire extinguishing bottles contain halon fire extinguishing agent pressurized with nitrogen. You use the engine fire switches in the flight deck to release the halon. Halon from each bottle can go to the left or right engine. EICAS messages, status messages, and indicator lights show when the bottle pressure is low.
Flight Deck Component Locations
The engine fire panel is in the flight deck on the P8 aisle stand.
Forward Cargo Compartment Component locations
The two engine fire extinguishing bottles are behind the right sidewall lining of the cargo door. Open the cargo compartment lining to get access to the bottles.
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 29 5/20/13 EFF - ALL
ENGINE FIRE EXTINGUISHING - COMPONENT LOCATIONS
SIDEWALLCARGO
2
BAY FLOORFWD CARGO
1
ENGINE FIRE BOTTLES
TUBEDISTRIBUTION
COMPARTMENTFWD CARGO
21FIRE CONTROL PANEL (P8)
ENG BTL1 DISCHENG BTL
LEF
1 2DISCH
T
1 2DISCH
THGIR
2 DISCH
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 30 5/20/13 EFF - ALL
ENGINE FIRE EXTINGUISHING - BOTTLES
Purpose
The engine fire extinguishing bottles contain the fire extinguishing agent.
Location
The engine fire extinguishing bottles are outboard of the right sidewall lining of the forward cargo compartment in the right rear corner.
Physical Description
The two engine fire extinguishing bottles are identical. Each bottle has these components:
• Safety relief and fill port • Low pressure switch • Two discharge assemblies • Switch test push button • Four mounting lugs
The engine fire extinguishing bottles are interchangeable with the APU fire extinguishing bottle.
Functional Description
The bottles contain 19 pounds of halon fire extinguishing agent pressurized to 825 psi with nitrogen. If the pressure in the bottle becomes too high, the safety relief and fill port opens so the bottle does not explode.
The discharge assembly has an explosive squib. An electric current from the fire extinguishing circuit fires the squib. This releases the halon through the discharge port.
The pressure switch gives flight deck indications when bottle pressure decreases. The switch monitors the pressure in the bottle and is normally open. When the pressure decreases because of a leak or because of bottle discharge, the switch closes and causes the EICAS message.
Training Information Point
When you replace bottles, handle them carefully to prevent damage. Compare the weight of the new bottle with the weight on the identification plate. This prevents installation of a bottle which is not full.
The discharge ports of the bottle for the left and right engines are different sizes and are also color coded. This prevents crossed connections.
WARNING: BE CAREFUL WHEN YOU MOVE THE FIRE EXTINGUISHING BOTTLE. THE FIRE EXTINGUISHING BOTTLE IS HIGHLY PRESSURIZED AND HAS AN EXPLOSIVE CARTRIDGE AS A COMPONENT. ACCIDENTAL DISCHARGE OF THE FIRE EXTINGUISHING BOTTLE CAN CAUSE INJURY TO PERSONS OR DAMAGE TO EQUIPMEMT.
WARNING: DO NOT TOUCH THE SQUIB BEFORE YOU DO THE PROCEDURES FOR DEVICES THAT ARE SENSITIVE TO ELECTROSTATIC DISCHARGE. ELECTROSTATIC DISCHARGE CAN CAUSE THE FIRE BOTTLE TO RELEASE ITS CONTENTS SUDDENLY AND CAUSE INJURY TO PERSONS AND DAMAGE TO EQUIPMENT.
WARNING: PUT A PROTECTIVE COVER ON THE SQUIB. IF YOU DO NOT PUT A PROTECTIVE COVER ON THE SQUIB, THE FIRE EXTINGUISHING BOTTLE CAN RELEASE ITS CONTENTS SUDDENLY AND CAUSE INJURY TO PERSONS.
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 31 5/20/13 EFF - ALL
ENGINE FIRE EXTINGUISHING - BOTTLES
LUG (4)MOUNTING
SAFETY RELIEFLOW PRESSURE
L SQUIB
RIGHT ENGINE
LEFT ENGINE
GROUND WIRE R SQUIB
DISCHARGE PORT(1-1/4 INCH)
DISCHARGE PORTPORT (1 INCH)
SWITCH TESTPUSH BUTTON
SW (375 PSI) AND FILLER PORT(1925 PSI)
ENGINE FIRE BOTTLE(TYPICAL)
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 32 5/20/13 EFF - ALL
ENGINE FIRE EXTINGUISHING - BOTTLE/SQUIBS
Purpose
The squib releases the halon from the engine fire extinguishing bottle.
Location
The squib is in the discharge assembly at the bottom of the fire bottle. Each fire bottle has two squibs, one for each engine.
Physical Description
The squib is an electrically operated explosive device. The squib is adjacent to a bottle diaphragm that can break. The diaphragm normally seals the pressurized bottle.
Functional Description
The squib fires when you put the fire switch to the DISCH 1 or DISCH 2 position. The explosion opens the diaphragm. Nitrogen pressure in the bottle pushes the halon through the discharge port.
Training Information Point
You use the SQUIB TEST PANEL (P61) to do a squib test. See the fire protection section for more information about the squib tests.
WARNING: MAKE SURE THERE IS NO VOLTAGE AT THE ELECTRICAL CONNECTOR. IF THERE IS A VOLTAGE AT THE ELECTRICAL CONNECTOR, THE SQUIB CAN ACCIDENTALLY FIRE AND CAUSE THE FIRE EXTINGUISHING BOTTLE TO RELEASE ITS CONTENTS. ACCIDENTAL DISCHARGE OF THE FIRE EXTINGUISHING BOTTLE CAN CAUSE INJURY TO PERSONS OR DAMAGE TO EQUIPMENT.
WARNING: PUT A PROTECTIVE COVER ON THE SQUIB. IF YOU DO NOT PUT A PROTECTIVE COVER ON THE SQUIB, THE FIRE EXTINGUISHING BOTTLE CAN RELEASE ITS
CONTENTS SUDDENLY AND CAUSE INJURY TO PERSONS.
CAUTION: DO NOT PUT A SHUNT PLUG ON THE SQUIB. THE SHUNT PLUG CAN CAUSE DAMAGE TO THE SQUIB PINS.
The electrical connectors and the discharge assembly interface threads are different sizes and colors for the left and right engine squibs. This prevents an incorrect connection.
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 33 5/20/13 EFF - ALL
ENGINE FIRE EXTINGUISHING - BOTTLE/SQUIBS
GLAND NUT
DISCHARGEPORT
SQUIB
GROUND LUG
DIAPHRAGM
DISCHARGEASSEMBLY
BOTTLE (REF)
ELECTRICALCONNECTOR
LEFT SQUIB RIGHT SQUIBSQUIB ASSEMBLY
(TYPICAL)
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 34 5/20/13 EFF - ALL
ENGINE FIRE EXTINGUISHING - ENGINE FIRE PANEL
Purpose
The engine fire switches and engine fire bottle discharge lights are on the engine fire panel in easy reach of the flight crew.
Location
The engine fire panel is in the flight deck on the P8 aisle stand.
Physical Description
The engine fire panel has a fire switch for each engine and a discharge light for each fire bottle.
Quick release fasteners attach the panel to the aisle stand structure. Electrical connectors connect the panel to the airplane wiring.
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 35 5/20/13 EFF - ALL
ENGINE FIRE EXTINGUISHING - ENGINE FIRE PANEL
ENGINE FIRE PANEL
ENGINE BOTTLEDISCHARGE
QUICK RELEASEFASTENER (4)
ELECTRICAL
ENGINE
ENGINE FIREWARN LIGHT
ENGINE FIREOVERRIDE SW
CONNECTOR
FIRE SW
LIGHTS
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 36 5/20/13 EFF - ALL
ENGINE FIRE EXTINGUISHING - ENGINE FIRE SWITCH
Purpose
The engine fire switch does these four things:
• Gives an indication of an engine fire • Stops the engine • Isolates the engine from the airplane systems • Controls the engine fire extinguishing system
Physical Description
The engine fire switch includes these parts:
• Engine fire warning light • Solenoid • Engine fire override button • Push-pull switch contacts (internal) • Rotary switch contacts (internal) • Electrical connector
Functional Description
The solenoid locks the fire switch, so you cannot pull it accidently. If an engine has a fire, the fire warning light comes on, and the solenoid energizes to release the switch.
The fire override button lets you pull the fire switch when the solenoid is not energized.
When you pull the fire switch, the push-pull switch contacts operate electrical circuits that stop the engine and isolate it from the airplane systems.
When you pull the switch, you can turn it left or right to a mechanical stop at the discharge position. The rotary switch contacts close and operate the fire extinguishing system.
When you release the switch, a spring moves the switch a small distance from the discharge position to open the switch contacts.
You must put the switch back to the center position before you can push the switch in.
Training Information Point
The left engine and right engine fire switches are interchangeable. When operating the fire switches in the discharge position, make sure that the fire bottle discharge light illuminates.
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 37 5/20/13 EFF - ALL
ENGINE FIRE EXTINGUISHING - ENGINE FIRE SWITCH
SWITCH RELEASEDSWITCH LOCKED
SOLENOIDENERGIZED
ENGINE FIREOVERRIDE BUTTONPUSHED
ENGINE FIRE
ELECTRICALCONNECTOR
SWITCH POSITIONS
CENTER
DISCHARGE 2DISCHARGE 1
SPRING RETURNSPRING RETURN
(SWITCH CLOSED)(SWITCH CLOSED)
(SWITCH OPEN)(SWITCH OPEN)
ENGINE FIRE SWITCH (P8)
WARNING LIGHT
LEFT
DISCH21
SWITCH PULLED
ENGINE FIREOVERRIDEBUTTON
PUSH-PULLCONTACTS (INTERNAL)
ROTARY CONTACTS(INTERNAL)
MANUALLYSWITCH RELEASED
ELECTRICALLY
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 38 5/20/13 EFF - ALL
ENGINE FIRE EXTINGUISHING - BOTTLE DISCHARGE
General
Each bottle has two discharge assemblies. The discharge assemblies connect the bottles to the discharge manifolds. One manifold goes to discharge nozzles in the left engine nacelle. The other manifold goes to discharge nozzles in the right engine nacelle.
Functional Description
Explosive squibs in the discharge assemblies connect to the engine fire handles in the flight deck. Squibs for the left engine connect to the left handle. Squibs for the right engine connect to the right handle. A squib for bottle 1 fires when you rotate the related fire handle to DISCH 1. A squib for bottle 2 fires when you rotate the related handle to DISCH 2. When a squib fires, the bottle releases the halon into the engine nacelle.
A pressure switch monitors the pressure in each bottle. The switch turns on the discharge indicator light when the bottle pressure decreases. The switch also causes advisory and status messages to show.
Training information Point
Rigid tubes, color coded yellow, connect both bottles to the left engine nacelle. Flexible braided hoses, with a strip of blue tape, connect both bottles to the right engine nacelle. This color code prevents incorrect connection.
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 39 5/20/13 EFF - ALL
ENGINE FIRE EXTINGUISHING - BOTTLE DISCHARGE
TUBEDISTRIBUTION
21
ENGINE FIRE BOTTLES
(1 EACH SIDE)NOZZLE ON ENGINE
NOZZLES
L ENGINE
R ENGINE
RIGHT ENGINE(LEFT SIMILAR)
ON STRUT
COMPARTMENTFWD CARGO
21
BAY FLOORFWD CARGOSIDEWALL
CARGO
LEFT
1 2DISCH
1 2DISCH
THGIR
R ENGOVHT2 DISCH
ENG BTL1 DISCH
ENG BTLOVHTL ENG
FIRE CONTROL PANEL (P8)
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 40 5/20/13 EFF - ALL
ENGINE FIRE EXTINGUISHING - ENGINE FIRE CIRCUIT SWITCH - OPERATION
General
The engine fire switch includes these components:
• Solenoid • Fire warning lights • Two sets of electrical contacts
One set of contacts controls engine functions. The other set of contacts controls the engine fire extinguishing system.
Solenoid and Warning Light Operation
The solenoid energizes if an engine has a fire. This releases the fire handle so you can pull it. The engine fire warning lights come on to show the correct handle to use.
The same condition normally occurs in both engine fire switches when you do a fire/overheat test.
You can override the solenoid with the engine fire override button.
Out Position
The operations that happen when you pull the fire handle are on the chart.
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 41 5/20/13 EFF - ALL
ENGINE FIRE EXTINGUISHING - ENGINE FIRE CIRCUIT SWITCH - OPERATION
CLOSES PRESSURE REGULATION AND SHUTOFF
FIRE SWITCH
SW UNLOCKSOLENOID
NORMAL
FIRE
FUNCTION WHEN PULLEDSYSTEM
CAUTION &
SHUTS OFF ENGINE FUEL CONDITIONING ACTUATOR
VALVE (PRSOV)
RESETS FIRE BELL AND SHOWS MESSAGE FOR ENGSHUTDOWN ON CAUTION ANNUNCIATOR
SWITCH IS PULLED AND THEN TURNEDDISCHARGES FIRE EXTINGUISH AGENT WHEN FIRE
FIRE SWITCH WHEN ENG FIRE IS DETECTEDUNLOCKS FIRE SWITCH SOLENOID AND TURNS ON
ENGINE T/R
FUEL CONDITIONCONTROL
PNEUMATICS
HYDRAULIC POWER
ENGINE FUELSHUTOFF VALVE
EXTINGUISHINGENGINE FIRE
FIRE DETECTION
GENERATOR
CLOSES REAR SPAR FUEL SHUTOFF VALVE
TRIPS ENG GENERATOR FIELD RELAY AND GCB
CLOSES ENG HYDRAULIC PUMP SUPPLY SHUTOFF VALVE
REMOVES POWER TO T/R ISOLATION VALVE
FIRE SWITCH(INTERNAL CONTACTS)
(TYPICAL)
R R R R
CONTROL
WARNING
FIRE HANDLE
FIRE HANDLE LIGHTS
LIGHTS
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 42 5/20/13 EFF - ALL
ENGINE FIRE EXTINGUISHING - CIRCUIT - FUNCTIONAL DESCRIPTION
Bottle Discharge
The engine fire switch sends power from the hot battery bus to the engine fire extinguishing bottle squibs. To discharge the bottle, pull out the handle and turn the handle clockwise or counterclockwise. The DISCH 1 position operates the squib for bottle 1. The DISCH 2 position operates the squib for bottle 2.
Discharge Indication
When pressure in the bottle decreases, the pressure switch closes and makes a ground for the discharge indicator light. The ground also causes EICAS to show advisory and status messages.
Training Information Point
You can do a check of the pressure switch circuit on the ground. Push and hold the test button to close the switch. The bottle discharge light in the flight deck should come on. Bottle discharge advisory and status messages should show.
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 43 5/20/13 EFF - ALL
ENGINE FIRE EXTINGUISHING - CIRCUIT - FUNCTIONAL DESCRIPTION
AA
AA
ENGINE FIRE
BOTTLE 2
DISCH 2
P
L ENG SQUIB
PRESSURE
ENGINE FIRE
BOTTLE 1
DISCH 1
LEFT ENGINE FIRE SW
ENG BTL 1 DISCH
ENG BTL 2 DISCH
MD&T
MD&T
28V DCHOT BATBUS
FIRE EXT
FIRE EXT
L ENG BTL 1
L ENG BTL 2
TESTBUTTON
P6-1 MN PWR DIST
EICAS COMPUTER
EXTINGUISHING
EXTINGUISHING
SWITCH
P
L ENG SQUIB
PRESSURE
TESTBUTTON
SWITCH28V DCHOT BATBUS
ENG BTL 1
ENG BTL 2
ADVISORY MSG
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 44 5/20/13 EFF - ALL
APU FIRE DETECTION - INTRODUCTION & LOCATION
Purpose
The APU fire detection system warns the flight or ground crew if there is an APU fire. The APU stops automatically if there is a fire. The APU has a fire extinguishing bottle forward of the APU firewall. You can stop the APU and discharge the extinguishing bottle from the P8 panel in the flight deck and the P40 panel on the nose gear.
Nose Landing Gear Component Location
The P40 service and APU shutdown panel is on the nose landing gear. The panel has an APU fire warning horn and an APU fire warning light.
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 45 5/20/13 EFF - ALL
APU FIRE DETECTION - INTRODUCTION & LOCATION
FIRE DETECTOR
P40 PANEL
FWD
APU BTLDISCH
DISCH APU
APU FIRE CONTROLPANEL (P8)
BOTTLEDISCHARGED
APUSHUTDOWN
APU BOTTLEDISCHARGE
FLIGHT DECKCALL
FLIGHTINPH
SERVICEINPH
EMER EXITLT TEST
WHEELWELLLIGHTS
OFF
APU FIREFIRE BOTTLE
ARMED
APU FIREWARNINGHORN
APU FIREWARNING HORN
APU FIREWARNING LIGHT
RS
LS
P40 SERVICE AND APU SHUTDOWN PANEL
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 46 5/20/13 EFF - ALL
GENERAL DESCRIPTION
General
The APU fire detection system has these components:
• APU fire detectors • Fire detection card • AFOLTS card
When a detector card for an APU fire detection loop senses a fire, it sends a signal to the automatic fire/overheat logic test system (AFOLTS) card.
The AFOLTS card uses AND logic, for example, both detector loops 1 and 2 must sense a fire for alarm signals to be sent.
When there is an APU fire, the AFOLTS card gives these indications:
• Warning light • Fire bell • APU fire handle light in red and unlocks • EICAS warning message, APU FIRE • APU remote shutdown panel warning light • APU warning horn when airplane is on ground
Also, when there is an APU fire, the APU shuts down.
To do a test of the system, push the ENG APU/CARGO test switch on the P8 test panel. This test gives flight compartment indications for engine fire and overheat. APU shutdown is prevented during the test.
The APU fire detection system has continuous and power-up tests. These tests do not send flight compartment verification, but failed APU loops show on the status and maintenance pages of EICAS.
When any test finds both loops defective, the system FAIL light comes on and the EICAS advisory message FIRE/OVHT SYS shows.
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 47 5/20/13 EFF - ALL
APU FIRE DETECTION - GENERAL DESCRIPTION
DISCH
APU BTLDISCH
APU
2DET
BOTTLEDISCHARGED
APUSHUTDOWN
APU BOTTLEDISCHARGE
FLIGHT DECK CALL
FLIGHT INPH
SERVICE INPH
EMER EXIT LT TEST
WHEELWELL LIGHTS
OFF
APU FIRE
FIRE BOTTLE ARMED
APU FIREWARNINGHORN
RS
LS
EICAS DISPLAY UNITS
DISCRETE WARNING DISPLAY
LOOP 1 AND LOOP 2ALARM/FAULT SIGNALS
ALARM WARNING SIGNAL 2
FIRE DETECTIONCARD FILE (P54)
LOOP 1 DETECTOR
LOOP 2 DETECTOR
INHIBITED DURING TEST
APU FIRE
SHUTDOWN PANELP40 APU REMOTE
WARNING ELEC
DUAL LOOP FAULT SIGNAL
UNIT (P51)
BELL/
AURAL &MASTERWARNINGMODULES
(P1-3)
AFOLTSCARD 3
(P2)
GND
STATUS/MAINT
FIRE/OVHT SYS (C)APU FIRE (A)
APU FIRE LP 1APU FIRE LP 2
ALARM WARNINGSIGNAL 1
1DET
(E8)COMPUTERSL (R) EICAS
APU SHUTDOWN
P7 (2)
CAUTION
WARNING AURALWARNING
1
CHIME
1
CONTROLPANEL (P8)
AFT CONTROLSTAND (P8)
APU TEST
CONFIG
OVSPD
A/PDISC
FIRE
CABINALT
PULL UP
SYS FAILWELLWHL
FIRE/OVHT TEST
ENG/APUCARGO
P-RESETFAIL
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 48 5/20/13 EFF - ALL
NOSE LANDING GEAR COMPONENT LOCATION
Nose Landing Gear Component Location
The P40 service and APU shutdown panel is on the nose landing gear. The panel has an APU fire warning horn and an APU fire warning light.
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 49 5/20/13 EFF - ALL
NOSE LANDING GEAR COMPONENT LOCATION
BOTTLEDISCHARGED
APUSHUTDOWN
APU BOTTLEDISCHARGE
FLIGHT DECKCALL
FLIGHTINPH
SERVICEINPH
EMER EXITLT TEST
WHEELWELLLIGHTS
OFF
APU FIREFIRE BOTTLE
ARMED
APU FIREWARNINGHORN
RS
LS
NOSE LANDING GEAR
P40 SERVICE AND APU SHUTDOWN PANEL
APU FIREWARNING HORN
APU FIREWARNING LIGHT
APU SHUTDOWNBUTTON BOTTLE DISCHARGE
BUTTON
BOTTLE ARMED
BOTTLE DISCHARGELIGHT
LIGHT
APU BTLDISCH
DISCH APU
APU FIRE CONTROLPANEL (P8)
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 50 5/20/13 EFF - ALL
APU FIRE DETECTORS
Purpose
The APU fire detectors detect fire or high temperatures in the APU compartment. The alarm signal shuts down the APU.
Physical Description
There are two fire detector assemblies. Each detector assembly has a loop 1 detector and a loop 2 detector attached to a support tube. The upper and lower fire detectors connect to make loop 1 and loop 2.
The fire detector assemblies have two sensing elements attached to a stainless steel support tube. The sensing element is used to find a fire or a temperature that is too hot. It consists of an Inconel tube with two electrical conductors in a thermistor material. The thermistor material in the Inconel tube decreases resistance when the material is heated.
Location
The upper detector assembly is attached to the airframe and the APU inlet plenum. The lower detector assembly is attached to the left APU access door.
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 51 5/20/13 EFF - ALL
APU FIRE DETECTORS
APU FIRE DETECTOR ASSEMBLY(TYPICAL)
ATTACHMENT LUGELEMENT SUPPORT TUBE
LOWER FIRE
UPPER FIREDETECTOR ASSEMBLY
DETECTOR ASSEMBLY(LEFT APU ACCESS DOOR)
APU COMPARTMENT(SIDE VIEW)
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 52 5/20/13 EFF - ALL
FIRE DETECTORS - FUNCTIONAL DESCRIPTION
Functional Description
The fire detector assemblies have two sensing elements attached to a stainless steel support tube. The sensing element is used to find a fire or a temperature that is too hot. It consists of an Inconel tube with two electrical conductors in a thermistor material. The thermistor material in the Inconel tube decreases resistance when the material is heated.
At normal ambient temperatures the sensing element resistance is high. The resistance decreases quickly as the element temperature increases. When the resistance decreases to a set point, an alarm signal goes to the AFOLTS card. If an electrical short occurs, the resistance decreases faster than when the high temperature causes the resistance change. The electrical short causes the logic in the detector card to send a fault signal to the AFOLTS card.
When the temperature decreases, the resistance increases above the reset value and the alarm signal stops.
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 53 5/20/13 EFF - ALL
FIRE DETECTORS - FUNCTIONAL DESCRIPTION
CONNECTION LOOP 1
QUICK RELEASECLAMP
SUPPORT TUBE
ELECTRICAL
ELECTRICAL
CONNECTION LOOP 2
HEAT SENSITIVEELECTRICALLYCONDUCTIVE MATERIAL
CENTRAL CONDUCTORS
1/16 INCH
APU FIRE DETECTOR
OUTER STEEL
(AS TEMPERATURE RISES,CONDUCTIVITY INCREASES)
(INPUT TO DETECTOR CARD)TUBE (GROUNDED)
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 54 5/20/13 EFF - ALL
AFOLTS CARD - FUNCTIONAL DESCRIPTION - SINGLE LOOP & DUAL LOOP
General - Dual Loop
The automatic fire and overheat logic and test system (AFOLTS) cards shows fire conditions when the detector cards receive alarm or fault signals from the fire detection loops 1 and 2. Outputs from the AFOLTS card give indications and flight compartment messages. The cards can operate in the dual loop mode (normal) or in a single loop mode.
An AFOLTS card receives alarm and fault signals from two detector cards. The detector cards connect to fire detection loops 1 and 2.
During dual loop mode operation an alarm or fault signal is necessary from the two detector cards to make an alarm warning of a fire condition.
General - Single Loop
The automatic fire/overheat logic test system (AFOLTS) can operate in a dual loop mode or a single loop mode.
The AFOLTS card selects a faulty detection loop off, after that loop fails a test. The test can be a self-test started when power connects to the battery bus or for a power interruption of more than two milliseconds, or the test can be a manual test from the P8 panel.
After an AFOLTS card finds a faulty loop in the fire detection system, only a single alarm or fault signal is necessary from the remaining good loop.
If a fire condition is found in the single loop mode, flight compartment warning and indications are the same as for the dual loop mode.
Test
When the card is in the dual loop mode, the card monitors loop 1 and loop 2 detector cards. If the detector card finds a fault with one or two of its loops during a power-up self-test or a manual test from the P8 panel, a fault signal goes to the AFOLTS card. AFOLTS sends status and maintenance messages to the flight compartment to show which loop has a failure. After a fault is found on one loop, the system does not use that loop and operates in the single loop
mode with different logic. If the two loops have failures, a SYS FAIL light shows on the P8 panel, and a FIRE/OVHT SYS advisory message shows on the flight compartment display.
Detector, card, or related wiring failures do not always give a valid fault output at the time of a failure. You must use the system test to find these loop failures.
Flight Compartment Messages
If the two loops have an output (alarm), the flight compartment warning message shows, and the loop status messages do not show.
Automatic 60-Minute Test
The AFOLTS card gives a self-test command to the detection zones when the detection loops, fire/overheat/smoke, in a zone are in disagreement for more than five seconds, or the zone is already in the single loop mode.The AFOLTS card gives the self-test command again each 60 minutes if the initial condition does not change or stays in the single loop operation.
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 55 5/20/13 EFF - ALL
AFOLTS CARD - FUNCTIONAL DESCRIPTION - SINGLE LOOP & DUAL LOOP
TAKEOFF<20 SEC AFTER
<400 FEETRADIO ALTM
NOT PUSHEDMASTER WARN
2 FIRE WARNING BELL
1 MASTER WARNING LIGHTS (P7)
WARNING ELECTRONICS UNIT (P51)
AFOLTS (TYP) (P54)
1
2 FIRE SW LOCK RELEASE (P8)3 FUEL CONT SW LIGHT (P8)
1 FIRE SW LIGHTS (P8)P54
P54
SOFTWAREFAULTALARM
ALARM + ALARM = ALARMALARM + FAULT = ALARM
FAULT FAULT + ALARM = ALARM
FOUND BY A FAILED TESTCIRCUIT NOT IN OPERATION SIGNAL
EXTENSION ON TAKEOFFSTARTS BY NOSE STRUT
LOOP MSG (S/M)
LOOP MSG (S/M)
FAULT + FAULT = FAIL LIGHT
1 FIRE DISCRETE ANNUN (P1-3)
ALARM 2
ALARM 1R EICAS COMPUTER
L EICAS COMPUTER
EICAS LOOP 2
EICAS LOOP 1
ALARM
FAULT TESTALARM TEST
FAULT TESTALARM TEST
CARDDETECTORLOOP 2
FIRE/OVHT TEST PANEL (P8)
SEQUENCERTEST
CARDDETECTORLOOP 1
TEST SWITCH ENG/APU/CARGO
SYS FAIL LIGHT
FIRE/OVHT SYS
2 2
LOOP MSG (S/M)
LOOP MSG (S/M)
FIRE/OVHT SYS
NOTE: STATUS LOOP MSGS INHIBITED
MAINTENANCE LOOP MSGS SHOW
T
(ADVISORY)
(ADVISORY)
DURING AN ALARM
DURING AN ALARM
2
1
ALARM OR FAULT + NOTHING FORMORE THAN 5 SEC = TEST EACH60 MINUTES
T
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 56 5/20/13 EFF - ALL
APU FIRE DETECTION - INDICATIONS
Purpose
The nose gear panel lets the ground crew stop operation of and extinguish the fire in the APU from the ground. The flight compartment also has a panel to stop operation of the APU and release the contents of the fire extinguishing bottle.
Physical Description
The flight compartment panel has a fire warning light and a T-handle to release the contents of the extinguishing bottle. The panel has a bottle discharge light.
The P40 panel has an APU fire warning horn and an APU FIRE warning light.
The panel has an APU SHUTDOWN button. The panel also has a FIRE BOTTLE ARMED light, APU BOTTLE DISCHARGE button, and BOTTLE DISCHARGED light.
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 57 5/20/13 EFF - ALL
APU FIRE DETECTION - INDICATIONS
BOTTLEDISCHARGED
APUSHUTDOWN
APU BOTTLEDISCHARGE
FLIGHT DECKCALL
FLIGHTINPH
SERVICEINPH
EMER EXITLT TEST
WHEELWELLLIGHTS
OFF
APU FIREFIRE BOTTLE
ARMED
APU FIREWARNINGHORN
RS
LS
NOSE LANDING GEAR
P40 SERVICE AND APU SHUTDOWN PANEL
APU FIREWARNING HORN
APU FIREWARNING LIGHT
APU SHUTDOWNBUTTON BOTTLE DISCHARGE
BUTTON
BOTTLE ARMED
BOTTLE DISCHARGELIGHT
LIGHT
APU BTLDISCH
DISCH APU
APU FIRE CONTROLPANEL (P8)
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 58 5/20/13 EFF - ALL
APU FIRE EXTINGUISHING - INTRODUCTION
Purpose
The APU fire extinguishing system extinguishes fires in the APU compartment.
General
If there is a fire, you can release the APU fire extinguisher bottle content manually from the P8 APU fire control panel or from the P40 APU remote control panel.
The APU fire extinguishing system has these components:
• APU fire extinguishing bottle • APU fire extinguishing bottle squib • Cargo fire/engine control module • APU fire switches • APU remote control panel (P40)
A bottle is forward of the APU fire wall on the lower right side. When you release the bottle content, a nozzle moves the extinguishing agent to the APU compartment.
The bottle releases its content by a squib. Control of the squib comes from the flight compartment or from the APU remote control panel on the nose landing gear. Flight compartment operation is with the APU fire handle on the P8 panel.
This handle locks down by a solenoid that releases for an APU fire. After you pull the fire handle, you can turn it in either direction to release the bottle contents. A bottle discharge light on the P8 panel and also on the P40 panel comes on when the bottle pressure decreases.
EICAS messages and indicator lights show when the bottle pressure is low.
Operation
The APU fire extinguishing bottle holds halon fire extinguishing agent pressurized with nitrogen. A discharge assembly connects the bottle to a discharge tube. The tube goes to a discharge nozzle in the APU compartment.
An explosive squib in the discharge assembly releases the halon from the bottle. The squib connects to the fire switches.
A pressure switch monitors the pressure in the bottle. After the bottle releases its content, the switch causes the discharge indicator lights to come on. The switch also causes EICAS advisory and status messages to show.
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 59 5/20/13 EFF - ALL
APU FIRE EXTINGUISHING - INTRODUCTION
APU BTLDISCH
DISCH APU
APU REMOTE CONTROLPANEL (P40)
(NOSE LANDING GEAR)
BOTTLEDISCHARGED
APU FIRESHUTDOWN
APU BOTTLEDISCHARGE
FLIGHT DECKCALL
FLIGHTINPH
SERVICEINPH
EMER EXITLT TEST
WHEELWELLLIGHTS
OFF
APU FIREFIRE BOTTLE
ARMED
APU FIREWARNINGHORN
RS
LS
APU
SERVICE
BOTTLEEXTINGUISHINGFIRE
APU FIRE CONTROLPANEL (P8)
ACCESS
2
1TEST
AFT
FWDTEST 2
TEST 12A21
CARGO
RL APUENGSQUIB TEST
TEST PANEL (P61)
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 60 5/20/13 EFF - ALL
APU FIRE EXTINGUISHING - GENERAL DESCRIPTION
General
The APU fire extinguishing system has these components:
• APU fire extinguishing bottle • APU fire extinguishing bottle squib • Cargo fire/engine control module • APU fire switches • APU remote control panel (P40).
A bottle is forward of the APU fire wall on the lower right side. When you release the bottle content, a nozzle moves the extinguishing agent to the APU compartment.
The bottle releases its content by a squib. Control of the squib comes from the flight compartment or from the APU remote control panel on the nose landing gear. Flight compartment operation is with the APU fire handle on the P8 panel.
This handle locks down by a solenoid that releases for an APU fire. After you pull the fire handle, you can turn it in either direction to release the bottle contents. A bottle discharge light on the P8 panel and also on the P40 panel comes on when the bottle pressure decreases.
EICAS messages and indicator lights show when the bottle pressure is low.
Operation
The APU fire extinguishing bottle holds halon fire extinguishing agent pressurized with nitrogen. A discharge assembly connects the bottle to a discharge tube. The tube goes to a discharge nozzle in the APU compartment.
An explosive squib in the discharge assembly releases the halon from the bottle. The squib connects to the fire switches.
A pressure switch monitors the pressure in the bottle. After the bottle releases its content, the switch causes the discharge indicator lights to come on. The switch also causes EICAS advisory and status messages to show.
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 61 5/20/13 EFF - ALL
APU FIRE EXTINGUISHING - GENERAL DESCRIPTION
APU BTLDISCH
DISCH APU
APU REMOTE CONTROLPANEL (P40)
BOTTLEDISCHARGED
APU FIRESHUTDOWN
APU BOTTLEDISCHARGE
FLIGHT DECKCALL
FLIGHTINPH
SERVICEINPH
EMER EXITLT TEST
WHEELWELLLIGHTS
OFF
APU FIREFIRE BOTTLE
ARMED
APU FIREWARNINGHORN
APU
SERVICE
BOTTLEEXTINGUISHINGFIRE
APU FIRE CONTROLPANEL (P8)
ACCESS
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 62 5/20/13 EFF - ALL
APU FIRE EXTINGUISHING - EXTINGUISHING BOTTLE
Purpose
The APU fire extinguishing bottle contains the Halon fire extinguishing agent.
Location
The fire extinguishing bottle is on the forward side of the APU fire wall, in the control bay.
Physical Description
The fire extinguishing bottle has these components:
• Safety relief and fill port • Pressure switch • Squib • Two discharge assemblies
The fire extinguishing bottle is interchangeable with the engine fire extinguishing bottles. Caps cover one squib and discharge port.
Functional Description
The bottle contains halon fire extinguishing agent pressurized with nitrogen. If the pressure in the bottle becomes too high, the safety relief port opens.
The discharge assembly has an explosive squib. An electric current from the fire extinguishing circuit fires the squib. This ruptures the frangible disk which releases the halon through the discharge port.
The pressure switch gives control panel indications when bottle pressure decreases. The switch monitors the pressure inside the bottle and is normally open. When the bottle pressure decreases because of a leak or bottle discharge, the switch closes and causes an EICAS message, APU BTL 1/2.
Training Information Point
To do a test of the switch circuits, push the manual override button on the pressure switch housing.
The squib can be removed and replaced without damage to the rupture disc. There is no squib installed on the unused discharge port. The unused port is capped off.
WARNING: INSTALL THE PROTECTIVE COVER ON THE SQUIB WHEN THE AIRPLANE WIRING IS DISCONNECTED FROM THE SQUIB. INCORRECT PROCEDURES OR EQUIPMENT COULD FIRE THE SQUIB AND CAUSE INJURY.
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 63 5/20/13 EFF - ALL
APU FIRE EXTINGUISHING - EXTINGUISHING BOTTLEDISCHARGE ASSEMBLY
PRESSURE SWITCHFRONT VIEW
LOOKING OUTBOARD TO THE RIGHT SIDE
CAP
BUTTONOVERRIDEMANUAL
CONNECTORELECTRICAL
FWD
SQUIB
SCREEN
DISKFRANGIBLE
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 64 5/20/13 EFF - ALL
APU FIRE CONTROL PANEL
Purpose
The cargo/APU fire control panel permits flight deck control of the APU and cargo fire extinguishing systems.
Location
The cargo/APU fire control panel is in the flight deck on the P8 aisle stand panel.
Physical Description
The cargo/APU fire control panel has a fire switch for the APU and a discharge light for the APU fire bottle.
Quick release fasteners attach the module to the aisle stand structure. Electrical connectors connect the airplane wires to the panel.
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 65 5/20/13 EFF - ALL
BTL DISCH
ARMEDARMED
DISCH
DISCH
FWD
FWD AFT
AFT
ARM
CARGO FIRE
APU BTLDISCH
APU
APU FIRE CONTROL PANEL (P8)
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 66 5/20/13 EFF - ALL
APU FIRE EXTINGUISHING - APU FIRE CONTROL PANEL & SWITCHES
Purpose
The cargo/APU fire control panel permits flight deck control of the APU and cargo fire extinguishing systems.
Location
The cargo/APU fire control panel is in the flight deck on the P8 aisle stand panel.
Physical Description
The cargo/APU fire control panel has a fire switch for the APU and a discharge light for the APU fire bottle.
Quick release fasteners attach the module to the aisle stand structure. Electrical connectors connect the airplane wires to the panel.
Purpose
The APU fire switch gives an indication of an APU fire and controls the APU fire extinguishing system.
Location
The APU fire switch is on the APU/cargo fire control panel.
Physical Description
The APU fire switch includes these parts:
• APU fire warning light • Solenoid • APU fire override button • Push-pull switch contacts (internal not shown) • Rotary switch contacts (internal not shown)
The fire warning light uses four lamps.
Functional Description
The solenoid locks the fire switch so you cannot pull it accidently. If the APU has a fire, the fire warning light comes on and the solenoid energizes to release the switch.
When you pull the fire switch, the push-pull switch contacts isolate the APU from the airplane systems.
When the switch is out, you can turn it left or right to a mechanical stop at the discharge position. The rotary switch contacts close and operate the fire extinguishing system.
When you release the switch, a spring moves the switch a small distance from the discharge position to open the rotary switch contacts.
The fire override button lets you pull the fire switch when the solenoid is not energized.
You must put the switch back to the center position before you can push the switch in.
Training Information Point
The engine and APU fire switches are not interchangeable. The fire warning light labels and the electrical connectors are different.
When operating the fire switches in the discharge position, make sure that the fire bottle discharge light illuminates.
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 67 5/20/13 EFF - ALL
APU FIRE EXTINGUISHING - APU FIRE CONTROL PANEL & SWITCHES
DISCH APUCENTER
SPRING RETURN(SWITCH OPEN)
DISCHARGE(SWITCH CLOSED)
SPRING RETURN(SWITCH OPEN)
DISCHARGE(SWITCH CLOSED)
APU/CARGO FIRE CONTROL PANEL (P8) SWITCH POSITIONS
SWITCH RELEASEDSWITCH LOCKED SWITCH PULLEDMANUALLY
SOLENOIDENERGIZED
APU FIREOVERRIDEBUTTONPUSHED
SWITCH RELEASEDELECTRICALLY
APU BTLDISCH
DISCH APUAPU FIRE WARNINGLIGHT
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 68 5/20/13 EFF - ALL
APU FIRE SWITCH - OPERATION
Warning Light and Solenoid Operation
The APU fire warning light comes on if there is an APU fire. The solenoid energizes and releases the fire switch so you can pull it.
This also occurs when you do a fire/overheat test.
Out Position
When you pull the fire switch, these functions occur:
• Generator field trips • APU fuel shutoff valve closes • APU shutoff valve closes • APU stops • EICAS messages which are not necessary do not show • Fire warnings at the P40 panel are canceled
Discharge Positions
The left or right DISCH position operates the APU fire extinguishing bottle squib.
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 69 5/20/13 EFF - ALL
APU FIRE SWITCH - OPERATION
SW UNLOCKSOLENOID
NORMAL
FIRE
FIRE SWITCH(INTERNAL CONTACTS)
R R R RFIRE HANDLE LIGHTS
CLOSES AIR SUPPLY APU VALVE
FUNCTION WHEN PULLEDSYSTEM
CAUTION AND
SHUTS DOWN APU WHEN FIRE HANDLE IS PULLED
RESETS FIRE BELL
SWITCH IS PULLED AND THEN TURNED LEFT OR RIGHTDISCHARGES FIRE EXTINGUISHING AGENT WHEN FIRE
SHUTS OFF APU FIRE HORN AIRPLANE ON GROUND
APU IGNITION AND
PNEUMATICS
ENGINE FUELSHUTOFF VALVE
EXTINGUISHINGENGINE FIRE
FIRE DETECTION
GENERATOR
CLOSES APU FUEL VALVE
TRIPS APU GENERATOR FIELD RELAY AND GCB
WARNING
APUAND REMOTE FIRE LIGHT AT NOSE GEAR
UNLOCKS FIRE SWITCH SOLENOID. TURNS ON FIRESWITCH WHEN APU FIRE DETECTED
STARTING
FIRE SWITCH(TYPICAL)
FIRE HANDLELIGHTS
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 70 5/20/13 EFF - ALL
FUNCTIONAL DESCRIPTION - CIRCUIT
General
Power for the APU fire handle on the P8 panel and the APU shutdown switch on the APU remote panel (P40) comes from the 28v dc hot battery. When you pull the fire handle or push the external shutdown switch, the APU fire extinguisher arms. The fire handle normally has a lock until there is a fire.
After you pull the fire handle or push the external shutdown switch, you turn the fire handle or push the APU bottle discharge switch on the P40 APU remote control panel to release the fire extinguisher content.
The APU access doors must be closed for the fire extinguisher to have the correct effect.
When the pressure in the bottle decreases, the pressure switch on the bottle closes and connects a ground to the APU bottle discharge lights.
Training Information Point
To do a test of the bottle discharge light circuit, you push the test button on the pressure switch assembly. This button connects the circuit and causes the two bottle discharge lights (P40 and P8) to come on. The message APU BTL also shows on the EICAS display.
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 71 5/20/13 EFF - ALL
FUNCTIONAL DESCRIPTION - CIRCUIT
PULL TO STOP APU, TURNTO RELEASE BOTTLE CONTENT
APU
APU
BOTTLE
EICAS COMPUTER
APU REMOTE CONTROL
FIREBOTTLE
DISCHARGEDBOTTLE
APU/CARGO FIRE
APU FIRE SWITCH
TEST 1
28V DCHOT BATBUS
APU 1FIRE EXT
(CW)
(CCW)
APU FIRE SW PUSHED P40
K421 EXTERNAL
APU BTL
(APU SHUTDOWN)
ADVISORY MSG
2
P11 CB PANEL
28V DCBAT BUS
FIRE INDAPU REMOTE
SHUTDOWN (P37)
CONTROL PANEL (P8)
ARMED
FIRE EXT
P6 CB PANEL
PANEL (P40)
G
1
A
A
SQUIB
PRESS
P
SWITCH
<400 PSI
DISCHARGE
MD&T
APUBOTTLE
2
1
SQUIB TESTPANEL (P61)
APU BTLDISCH
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 72 5/20/13 EFF - ALL
FREIGHTER LAVATORY - SMOKE DETECTION SYSTEM GEN-ERAL DESCRIPTION
General
The smoke detection system uses the JAMCO smoke detector. This smoke detector uses the ionization type system. The alarm is self contained in the unit along with a test button and a horn silencing button.
System Tests
The smoke detector is tested on the unit.
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 73 5/20/13 EFF - ALL
FREIGHTER LAVATORY - SMOKE DETECTION SYSTEM GENERAL DESCRIPTION
SMOKE DETECTOR
ALARM HORN
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 74 5/20/13 EFF - ALL
LOWER CARGO COMPARTMENT SMOKE DETECTION - INTRODUCTION
Purpose
The system gives a FWD or AFT CARGO FIRE WARNING indication in the flight compartment when smoke is detected in the air of the forward or aft cargo compartments.
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 75 5/20/13 EFF - ALL
LOWER CARGO COMPARTMENT SMOKE DETECTION - INTRODUCTION
AFT CARGOCOMPARTMENT
FWD CARGOCOMPARTMENT
SMOKEDETECTORS (2)
SMOKEDETECTORS (2)
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 76 5/20/13 EFF - ALL
LOWER CARGO COMPARTMENT SMOKE DETECTION - GEN-ERAL DESCRIPTION
Purpose
There are different smoke detection systems for each cargo compartment. The smoke detectors are connected to a venturi ejector system to move air through the sampling tubes past the light diodes.
General
The detectors operate when the pneumatic system is powered to move air through the sampling tubes.
During AND logic (normal) operation, the two detectors must sense smoke to cause fire signals 1 and 2 to go to the AFOLTS card. During OR logic (one detector failure) operation, only one detector is necessary to send a signal to the AFOLTS card.
System Tests
AFOLTS card 6 monitors and does a test of the smoke detectors (fwd/aft). The annunciator lights and EICAS messages show this data:
• Location of a fire • Smoke detector with a failure • Detector fan with a failure • System (fwd/aft) with a failure.
You can use the ENG/APU/CARGO FIRE test switch to start a manual test. This test is almost the same as the power-up test.
General Component Locations
The smoke detector assemblies for the forward cargo compartment are located with the main deck smoke detector assemblies for zones A, B, and C. The smoke detectors are located on the left side of the lower forward cargo compartment across from the forward cargo door. The smoke detector assemblies for the aft cargo compartment are located with the main deck smoke detectors for zones D, E, and F. The smoke detectors are located on the left side of the aft lower cargo compartment across from the aft cargo door.
AFOLTS card No. 6 is in the fire detection card file (P54). The cargo fire detectors are tested from the FIRE/OVHT test panel (P8) using the same test switch for engine and APU fire loops.
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 77 5/20/13 EFF - ALL
LOWER CARGO COMPARTMENT SMOKE DETECTION - GENERAL DESCRIPTION
A2
1
DISCH
FWD
MAIN
AFT DISCHDEPR/
ARM
ARM
CARGO FIRE
DISCH
DEPR
FWD
ARMED
ARMED
AFT
ARMED
MAIN
WARNINGELECTRONICS UNIT (P51)
BELL/CHIMEAURAL&MASTERWARNINGMODULES
FWD CARGOCOMPARTMENT
COMPARTMENTAFT CARGO
SMOKE DET ASSEMBLY
AFOLTSCARD 6
FIRE DETECTIONCARD FILE (P54)
FWD CARGODET 1
FWD CARGODET 2
SYSTEM MANUAL TEST
ALARM WARNING SIGNAL NO 2
ALARM WARNING SIGNAL NO 1
EICAS DISPLAYCOMPUTERSL(R) EICAS
FWD CARGO FIRE
FWD CARGO DET 1FWD CARGO DET 2
STATUS/MAINT
FIRE/OVHT SYS
DUAL LOOP FAULT SIGNAL
LOOP 1 AND LOOP 2 ALARM/FAULT SIGNALS
CABIN
PULL UP DISCA/P
OVSPD
CONFIGFIRE
ALT
WARNING
CAUTION
P7 (2)
FIRE BELL (2)
(E8)UNITS (P2)
FAIL
ENG/APUFIRE/OVHT TEST
CARGOWELLWHL SYS FAIL
P-RESET
FIRE/OVHT TEST PANEL (P8) CARGO FIRE CONTROL PANEL (P8)
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 78 5/20/13 EFF - ALL
FLIGHT DECK CONTROLS
Component Locations
These are the components in the flight deck that have an interface with the lower cargo compartment smoke detection system:
• Master warning and caution (P7) • FIRE/OVHT test panel (P8) • Fire bell (2) • Discrete warning display (P1-3)
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 79 5/20/13 EFF - ALL
FLIGHT DECK CONTROLSCARGO FIRE CONTROL PANEL (P8)FIRE TEST PANEL (P8)
FAIL
ENG/APU
FIRE/OVHT TEST
CARGOWELLWHL SYS FAIL
P-RESET
WARNING
CAUTION
P7 (2)
FIRE BELL (2)
A2
1
DISCH
FWD
MAIN
AFT DISCHDEPR/
ARM
ARM
CARGO FIRE
DISCH
DEPR
FWD
ARMED
ARMED
AFT
ARMED
MAIN
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 80 5/20/13 EFF - ALL
LOWER CARGO COMPARTMENT COMPONENT LOCATION
General Component Locations
The smoke detector assemblies for the forward cargo compartment are located with the main deck smoke detector assemblies for zones A, B, and C. The smoke detectors are located on the left side of the lower forward cargo compartment across from the forward cargo door. The smoke detector assemblies for the aft cargo compartment are located with the main deck smoke detectors for zones D, E, and F. The smoke detectors are located on the left side of the aft lower cargo compartment across from the aft cargo door.
AFOLTS card No. 6 is in the fire detection card file (P54). The cargo fire detectors are tested from the FIRE/OVHT test panel (P8) using the same test switch for engine and APU fire loops.
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 81 5/20/13 EFF - ALL
LOWER CARGO COMPARTMENT COMPONENT LOCATION
MAIN DECKSMOKE
FROMSAMPLINGPORTS
FROMSAMPLINGPORTS
SMOKESAMPLINGPORTS
SMOKE DETECTOR 2FWD CARGO
FWD CARGOSMOKE DETECTOR 1
TO VENTURIEJECTOR
TO VENTURIEJECTOR
AFT CARGOSMOKE
AFT CARGOSMOKE
AFT DETECTORS
FORWARD DETECTORS
DETECTOR DETECTOR 2
DETECTOR 1
MAIN DECKSMOKEDETECTOR
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 82 5/20/13 EFF - ALL
LOWER CARGO COMPARTMENT SMOKE DETECTION - SMOKE DETECTOR
Purpose
The smoke detectors monitor air in the cargo compartments for smoke. The venturi ejector provides the source of power to move the air from the cargo compartment into the smoke detector.
Physical Description
All cargo compartment smoke detectors are identical and interchangeable.
The detector consists of a photo diode and light emitting diode (LED) in a chamber. There are two printed wiring board assemblies in each chamber.
The detector has inlet and outlet tubes that protrude from the chamber to give airflow through the detector.
Functional Description
The smoke detector uses an optical principle to detect smoke. The detector consists of a photodiode and light emitting diode (LED) in a chamber. The detector has inlet and outlet tubes for air access. The beam of light from the light emitting diode shines into a light trap. The smoke particles reflect part of the beam of light onto the photodiode. The photodiode current increases with the amount of smoke that enters the detector. When the voltage is more than a preset level, a relay energizes to provide an alarm signal
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 83 5/20/13 EFF - ALL
LOWER CARGO COMPARTMENT SMOKE DETECTION - SMOKE DETECTOR
NON-REFLECTIVESURFACE
LEDPARTICLESSMOKE
PHOTO DIODE
INTENSITY
ALARMPHOTO
CONNECTOR
AIR IN
AIR OUT
SMOKE DETECTOR INTERNAL
DIODE
CONTROL
BEAMLIGHT
ELECTRICAL
FROMSAMPLINGPORTS
SMOKESAMPLINGPORTS
SMOKE DETECTOR 2FWD CARGO
FWD CARGOSMOKE DETECTOR 1
TO VENTURIEJECTOR
FORWARD DETECTORS
MAIN DECKSMOKEDETECTOR
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 84 5/20/13 EFF - ALL
LOWER CARGO COMPARTMENT SMOKE DETECTION - DETECTOR LOCATION
Component Location
The forward cargo smoke detector assemblies are on the left side of the forward cargo compartment next to the main deck detectors zones A, B, and C. The smoke detectors are opposite the cargo door in the forward compartment. The aft cargo smoke detectors are on the left side of the aft cargo compartment next to the main deck detectors zones D, E, and F. The smoke detectors are opposite the cargo door in the aft compartment.
AFOLTS card 6 is in the P54 fire detection card file. The cargo fire detector tests are done from the FIRE/OVHT test panel (P8) with the same test switch for engine and APU fire loops.
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 85 5/20/13 EFF - ALL
LOWER CARGO COMPARTMENT SMOKE DETECTION - DETECTOR LOCATION
FROMSAMPLINGPORTS
SMOKESAMPLINGPORTS
SMOKE DETECTOR 2FWD CARGO
FWD CARGOSMOKE DETECTOR 1
TO VENTURIEJECTOR
FORWARD DETECTORS
MAIN DECKSMOKEDETECTOR
SMOKEDETECTORS
JOINS VENTURI EJECTOR
SMOKE DETECTOR ASSEMBLY
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 86 5/20/13 EFF - ALL
LOWER CARGO COMPARTMENT SMOKE DETECTION - SMOKE DETECTOR - FUNCTIONAL DESCRIPTION
Functional Description
During normal operation, a beam of light from the light emitting diode shines into the light trap. Photo diode current comes from the light that reflects from the chamber surface.
As smoke enters the detector, a portion of the beam of light reflects from the smoke particles onto the photo diode. This causes the photo diode current to increase with the amount of smoke that enters the detector. Amplifiers raise this photo diode current to a detectable voltage level.
When the voltage is more than a preset level, a relay energizes to give an alarm signal.
A test of the smoke detector verifies that the LED light source is not burned out. The test also makes sure the smoke detector has a minimum guaranteed sensitivity.
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 87 5/20/13 EFF - ALL
LOWER CARGO COMPARTMENT SMOKE DETECTION - SMOKE DETECTOR - FUNCTIONAL DESCRIPTION
SMOKE DETECTOR
AIR IN
NON-REFLECTIVESURFACE
LEDPARTICLESSMOKE
PHOTO DIODE
INTENSITY
ALARMPHOTO
CONNECTOR
AIR IN
AIR OUT
SMOKE DETECTOR INTERNAL
DIODE
CONTROL
BEAMLIGHT
ELECTRICALELECTRICALCONNECTOR
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 88 5/20/13 EFF - ALL
INDICATIONS
Component Locations
These components in the flight compartment have an interface with the lower cargo compartment smoke detection system:
• Master warning and caution on P7 • FIRE/OVHT test panel on P8 • Discrete warning display on P1-3 • Fire bell (2)
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 89 5/20/13 EFF - ALL
INDICATIONS
ARMED
FWD
ARMED
AFT
ARMED
MAIN
SYS FAILWELLWHL
FIRE/OVHT TEST
ENG/APUCARGO
P-RESETFAIL
ENG/APUCARGO
FIRE/OVHT TEST PANEL (P8)CABIN
ALT
FIRE CONFIG
OVSPD
A/PDISCPULL UP
(P1-3)DISCRETE WARNING DISPLAY
DISCHDEPR/
CARGO FIREFWD
DEPR
MAIN
DISCH
A
AFT
RM
DISCHARM 1
CARGO FIRE CONTROL PANEL(P8)
P-5 PANEL
FIRE BELL (2)
WARNING
CAUTION
P7 (2)
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 90 5/20/13 EFF - ALL
AFOLTS CARD - FUNCTIONAL DESCRIPTION - DUAL LOOP
General
The automatic fire and overheat logic and test system (AFOLTS) card shows fire conditions when the detector cards receive an alarm from the smoke detectors. Outputs from the AFOLTS card give indications and flight compartment messages. The cards can operate in the dual loop mode (normal) or a single loop mode. The dual loop mode shows here.
An AFOLTS card receives alarm and fault signals from four smoke detectors, two in each of the cargo compartments. Each smoke detector is a loop.
During dual loop mode operation, an alarm or fault signal is necessary from the two detector cards to make an alarm warning of a fire condition.
EICAS
A single loop output shows as a message on the status and maintenance pages. If the two loops have an output (alarm), the EICAS display changes to a warning, and the loop messages do not show.
Test
When the AFOLTS card is in the dual loop mode, the card monitors loop 1 and loop 2 smoke detectors. If the AFOLTS card finds a fault with one or two smoke detectors for a cargo compartment during a power-up self-test or a manual test from the P8 panel, AFOLTS sends status and maintenance messages to the flight compartment to show which loop has a failure. If the card finds a fault with one loop, the system does not use that loop and operates in the single loop mode with different logic. If the two loops have failures, a SYS FAIL light and FIRE/OVHT SYS advisory message show in the flight compartment.
Smoke detectors or related wiring failures do not always give a valid fault output at the time of a failure. You must use a system test to find these loop failures.
Automatic 60-Minute Test
The AFOLTS card gives a self-test command to the detection zones when the detection loops, fire/overheat/smoke, in a zone are in disagreement for more than five seconds, or the zone is already in the single loop mode.
The AFOLTS card gives the self-test command again each 60 minutes if the initial condition does not change, or the system stays in the single loop operation.
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 91 5/20/13 EFF - ALL
AFOLTS CARD - FUNCTIONAL DESCRIPTION - DUAL LOOP
DETECTORSMOKESMOKE
LOOP 1DETECTORLOOP 2
ALARM OR FAULT + NOTHING FORMORE THAN 5 SEC = TEST EACH60 MINUTES
P54
P54
SOFTWAREFAULTALARM ALARM + ALARM = ALARM
ALARM + FAULT = ALARMFAULT FAULT + ALARM = ALARM 2 FIRE SW LOCK RELEASE (P8)
3 FUEL CONT SW LIGHT (P8)
1 FIRE SW LIGHTS (P8)
2 FIRE WARNING BELL
1 MASTER WARNING LIGHTS (P7)
FAULT + FAULT = FAIL LIGHT
1 FIRE DISCRETE ANN (P1-3)
ALARM 2
ALARM 1
EICAS LOOP 2
EICAS LOOP 1
ALARM
FAULT TEST
ALARM TEST
FAULT TESTALARM TEST
FIRE/OVHT TEST PANEL (P8)SEQUENCERTEST
AFOLTS (TYP) (P54)
TEST SWITCHENG/APU/CARGO
SYS FAIL LIGHT
2 2R EICAS COMPUTER
L EICAS COMPUTER
LOOP MSG (S&M)
LOOP MSG (S&M)
FIRE/OVHT SYS
TAKEOFF<20 SEC AFTER
<400 FEETRADIO ALTM
NOT PUSHEDMASTER WARN
WARNING ELECTRONICS UNIT (P51)
1
NOTE: STATUS LOOP MSGS INHIBIT DURING AN ALARM; MAINTENANCE LOOP MSGS SHOW DURING
FOUND BY A FAILED TESTCIRCUIT NO OPERATION SIGNAL ASEXTENSION ON TAKEOFFSTARTS BY NOSE STRUT1
2
AN ALARM
LOOP MSG (S&M)
LOOP MSG (S&M)
FIRE/OVHT SYS
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 92 5/20/13 EFF - ALL
MAIN DECK CARGO SMOKE DETECTION SYSTEM - GEN-ERAL DESCRIPTION
General
The smoke detection system for the main deck cargo compartment is divided into 6 zones (Zones A - F). The smoke detection system monitors the air in the cargo compartment and provides alerts for a smoke condition.
The main deck cargo compartment uses 12 smoke detectors arranged in 6 pairs making up two loops. Each main deck cargo compartment smoke detector connects to the test alarm interface module (TAIM). The TAIM transmits the status of loop one and loop two signals from the main deck smoke detectors in order to provide alarm signals to AFOLTS. The TAIM is located in the main equipment center by the E3 rack.
There is one AFOLTS card for main deck cargo compartment smoke detection. AFOLTS normally uses AND logic. If at least one smoke detector pair (loops 1 and 2) for the main deck sense smoke, you get the following indications:
• the red MAIN CARGO FIRE switch lights (on P8) • the red FIRE light (on P1-3) • the red master warning lights (on P7) • the fire bell sounds • MAIN CARGO FIRE warning message on EICAS
System Tests
The cargo smoke detectors are tested from the FIRE/OVHT test panel (on P8), using the same test switch for engine and APU. During a test, the TAIM sends the status of main deck cargo loops 1 and 2 to the AFOLTS card.
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 93 5/20/13 EFF - ALL
MAIN DECK CARGO SMOKE DETECTION SYSTEM - GENERAL DESCRIPTION
A2
1
DISCH
FWD
MAIN
AFT DISCHDEPR/
ARM
ARM
CARGO FIRE
DISCH
DEPR
FWD
ARMED
ARMED
AFT
ARMED
MAIN
DISCRETE WARNINGDISPLAY (P1-3)
CABIN
PULL UP DISCA/P
OVSPD
CONFIGFIRE
ALT
EICAS DISPLAY UNITS (P2)
(E8)COMPUTERSEICASL(R)
AFOLTSCARD 7
CARD FILE (P54)FIRE DETECTION
TEST/ALARMINTERFACEMODULE (M2039)
MAIN DECK LP 1SMOKE DETECTORS
SMOKE DETECTORSMAIN DECK LP 2
ELECTRONICSUNIT (P51)
WARNING
LOOP 1 AND LOOP 2
DUAL LOOP FAULT SIGNAL
ALARM WARNING SIGNAL NO. 2
SYSTEM MANUAL TEST
&
BELL/CHIMEAURAL
MASTERWARNINGMODULES
MN CARGO FIRE
MN CARGO LP 1MN CARGO LP 2
SIGNAL NO. 1ALARM WARNING
WARNING
CAUTION
P7 (2)
AURAL
SPEAKER (WARNING)INDICATION
STATUS/MAINT
FIRE/OVHT SYS
ALARM/FAULT SIGNALS
FIRE TEST PANEL (P8)
FAIL
ENG/APU
FIRE/OVHT TEST
CARGOWELLWHL SYS FAIL
P-RESET
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 94 5/20/13 EFF - ALL
SMOKE DETECTION SYSTEM - VENTURI EJECTOR AND PRESSURE SWITCH
Venturi Ejector
The venturi ejector uses bleed air to create a vacuum condition to pull sample air through the smoke detectors in the main deck and forward and aft lower cargo compartments. Sample air in each of the zones is drawn through the detectors via a duct distribution system. Smoke entering the light-proof chamber of the smoke detectors reflects the light from the pilot lamp onto the photocell.
The photocell gives a signal to an amplifier where the signal is processed and sent to a relay which provides an alarm output signal to the fire/overheat logic test card. The ejector is located aft of the mix manifold in the forward cargo compartment.
Pressure Switch
The pressure switch is installed on the ejector plenum in the aft end of the forward cargo compartment. When the gauge pressure falls below approximately seven inches of water, the pressure switch closes and causes an EICAS message. When the pressure is eleven inches of water or greater, the pressure switch will open and the EICAS message will disappear.
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 95 5/20/13 EFF - ALL
SMOKE DETECTION SYSTEM - VENTURI EJECTOR AND PRESSURE SWITCH
EJECTOR
SWITCHPRESSURE
MIX MANIFOLD
EJECTOR AND PRESSURE SWITCH
FWD
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 96 5/20/13 EFF - ALL
MAIN DECK SMOKE DETECTORS
Purpose
The main deck cargo compartment uses 12 smoke detectors to check for smoke in order to give flight deck indications when there is a fire.
Component Location
Smoke detectors are near the cargo doors in the forward and aft cargo compartments.
The smoke detectors for the forward main deck (zones A, B, and C) are located opposite the FWD cargo door in the lower cargo compartment. The smoke detectors for the aft main deck (zones D, E, and F) are located opposite the AFT cargo door in the lower cargo compartment.
Air sampling tubes in the ceiling of each zone connect to the detector pair for that zone.
Functional Description
The smoke detector uses an optical principle to detect smoke. The detector consists of a photodiode and light emitting diode (LED) in a chamber. The detector has inlet and outlet tubes for air access. The beam of light from the LED shines into a light trap. The smoke particles reflect part of the beam of light onto the photodiode. The photodiode current increases with the amount of smoke that enters the detector. When the voltage is more than a preset level, a relay energizes to provide an alarm signal.
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 97 5/20/13 EFF - ALL
MAIN DECK SMOKE DETECTORS
SMOKELOWER LOBE
LOWER LOBESMOKE DETECTORS
FROMSAMPLINGPORTS
FROMSAMPLINGPORTS
FROMSAMPLINGPORTS
SMOKESAMPLINGPORTS
LOOP 2LOOP 1
LOOP 2LOOP 1
FORWARD DETECTORS
LOOP 2LOOP 1
LOOP 2
TO VENTURIEJECTOR
LOOP 2LOOP 1
LOOP 2
LOOP 1
AFT DETECTORS
TO VENTURIEJECTOR
LOOP 1
ZONEA
ZONE B
ZONE C
ZONE D
ZONE E
ZONE F
ZONEA
ZONEB
ZONEC
ZONE F
ZONE E
ZONED
DETECTORS
INTAKE ORIFICE
CEILING
CARGOCOMPARTMENT
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 98 5/20/13 EFF - ALL
MAIN DECK CARGO COMPARTMENT SMOKE DETECTION - FUNCTIONAL DESCRIPTION
Purpose
The test/alarm interface module (TAIM) consolidates the signal inputs from the six pairs of main deck smoke detectors. Two separate and identical sections support a dual loop configuration.
Component Location
The TAIM is in the main equipment center attached to the inboard side of the E-3 rack.
Physical Description
The module has twelve indicator lamps (LEDs), a lamp test switch and two loop test switches.
Functional Description
The main deck smoke detectors operate the same way as the smoke detectors for the lower cargo compartment. A single AFOLTS card serves the main deck smoke detectors. The AFOLTS card logic remains unchanged.
Signals to and from the 12 main deck smoke detectors go through the test/alarm interface module (TAIM) The TAIM has two separate and identical sections to support dual loop configurations. Each half of the TAIM unit is seen by the AFOLTS card as one smoke detector.
The TAIM consolidates the 12 inputs (6 per loop) from the main deck smoke detectors into two inputs (1 per loop). This allows the AFOLTS card to look at signals from any main deck smoke detector as being from loop 1 or loop 2.
During normal operation, the TAIM operates in OR logic. Any one of the six detectors that comprises main deck loop 1 or loop 2 may send an alarm signal to AFOLTS. For example, when loop 1 detects smoke in Zone A, the TAIM outputs a loop 1 alarm signal. Therefore, when loop 2 Zone C senses smoke, a second alarm signal also goes to AFOLTS.
A system test is conducted by pressing the ENG/APU/CARGO fire test switch, or from the TAIM front panel test switches. As far as the TAIM is concerned, there is no difference in the source of the test input. The TAIM operates in AND logic during a test. During a system test, all detectors must signal an alarm before the alarm will be transmitted to the AFOLTS card.
If a faulty smoke detector is found during test, the TAIM unit does not output an alarm signal to AFOLTS for that loop, and AFOLTS gives a status/maintenance message to EICAS MAIN CARGO LOOP 1 (2). If two loops are inoperative, the FIRE/OVHT SYS message shows.
Anytime a detector fails a test, that detector loop annunciation on EICAS and AFOLTS configures to single loop operation. Failed individual smoke detectors can be found by doing a test of the TAIM.
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 99 5/20/13 EFF - ALL
MAIN DECK CARGO COMPARTMENT SMOKE DETECTION - FUNCTIONAL DESCRIPTION
ABCDETDETDET
FDET
DDETDET
E
REGULATION
LED
PHOTODIODE
M2027 MAIN DECK SMOKE DETECTORLOOP 1 ZONE A
TESTOUTPUTREGULATOR
LIGHT
A
B
FDETDET
C BMANUALTEST
ALARMLOOP 2
TESTLOOP 2
TESTMANUAL
M2039 TEST ALARM INTERFACE MODULE
DETDETDETE D
BUSBAT.28V DC
28V DCR BUS
LT RESET
CARGO TEST
MAIN CARGO FIREDETECTION ALTNPWR-MAIN CARGO
MAIN CARGO FIREDETECTION-1
MAIN CARGO FIREDETECTION-2
ENG/APU
SYS FAIL
FIRE
P11 PANEL
FIRE/OVHT SYSTEM "C"
MAIN CARGO FIRE "A"
MN CARGO LP 1 "S & M"
MN CARGO LP 2 "S & M"
SYS FAIL LT
MN CARGO LP 1
MN CARGO LP 2
MAIN CARGO FIRE 2
M10445 FIRE/OVHTTEST PANEL (P8)
MD&T
M10445 FIRE/OVHTTEST PANEL (P8)
LOGIC TEST CARDM2026 FIRE/OVERHEAT
MAIN CARGO FIRE 1
SYS FAIL LT RESETSYS TESTDET 1 FIRE
DET 1 TEST
LOOP 1 ALARM
LOOP 1 TEST
28V DC DET 128V DC DET 2DET 2 FIRE
DET 2 TEST
MD&T
A HALF
MD&T
DISCRETE WARNINGDISPLAY (P1)
(L/R) EICAS COMPUTERS
LOOP 2*INSTRUCTIONS*
1C 1B 1A
2C 2B 2A
1F 1E 1D
2F 2E 2D
LOOP 1
PRESSTO
TEST
1. PRESS LAMP TEST VERIFY ALL INDICATORS
2. PRESS AND HOLD TEST SWITCH FOR LOOP UNDER TEST.
ILLUMINATE.
3. VERIFY SIX INDICATORS ILLUMINATE, IF DETECTORIS FAILED, INDICATOR WILL NOT ILLUMINATE.
4. RELEASE LOOP TEST SWITCH.
MAIN CARGO COMPARTMENTSMOKE DETECTOR TEST FOR
PRESSTO TEST
LAMPS
A B
FAILRESET
MAIN
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 100 5/20/13 EFF - ALL
LOWER CARGO FIRE EXTINGUISHING - INTRODUCTION
Purpose
The lower cargo fire extinguishing system extinguishes fires in the forward or aft lower cargo compartments.
Physical Description
The lower cargo fire extinguishing system has these components:
• Fire extinguishing dump bottle 1 • Fire extinguishing metered bottles 2 and 2A • Three manifold pressure switches • Two regulators • Two filter/dryers • Six non-metered discharge nozzles • Five metered discharge nozzles
The fire extinguishing bottles contain halon 1301 fire extinguishing agent pressurized with nitrogen. Tubes connect the bottles to discharge nozzles in the cargo compartment ceiling and sidewall.
Operation
In the flight compartment, cargo fire arm switches set the discharge to the forward or aft compartment. The discharge switch starts the fire bottle discharge sequence. A line pressure switch puts on the DISCH indication to show the start of the discharge sequence.
The dump bottle releases its contents into the selected compartment when you push the discharge switch. The bottle releases its contents quickly to extinguish the fire.
After a time delay, the metered bottles release their contents slowly and at a controlled rate through the filter, dryer, and regulator units. Halon from the metered bottles replaces the extinguishing agent in the cargo compartment to keep the fire extinguished for 180 minutes.
The fire extinguisher bottles operate differently in flight than on the ground. If the airplane is on the ground when you push the discharge switch, bottle 1
releases its contents immediately, and bottles 2 and 2A start a metered release that continues until the bottles are empty.
If you push the discharge switch in flight, bottle 1 releases its contents immediately, and bottles 2 and 2A start to release their contents 30 minutes after bottle 1.
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 101 5/20/13 EFF - ALL
LOWER CARGO FIRE EXTINGUISHING - INTRODUCTION
COMPARTMENT (REF)FORWARD CARGO
BOTTLES
ENGINE FIREEXTINGUISHER
BOTTLESFIRE EXTINGUISHERCOMPARTMENTCARGO
APU FIRE
BOTTLESEXTINGUISHER
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 102 5/20/13 EFF - ALL
LOWER CARGO COMPARTMENT - GENERAL DESCRIPTION
Flight Compartment
The flight compartment has a control panel to arm and operate the cargo fire extinguishing bottles to release the bottle contents into the forward or aft cargo compartment.
Lower Forward Cargo Compartment
The lower cargo fire extinguishing system uses these components to extinguish fires in one or the other lower cargo compartment:
• Fire extinguishing bottles (3) • Filter/dryers (2) • Manifold pressure switches • Regulators (2)
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 103 5/20/13 EFF - ALL
LOWER CARGO COMPARTMENT - GENERAL DESCRIPTION
NOZZLEOUTLETMETERED
AFT COMPT DOORCARGO
DOORCARGO
2A
TEMP COMPENSATEDLOW PRESSURE SWITCHES2
BULK
UNMETEREDOUTLET NOZZLE
(REF)DOORCARGO
LOW
CIRCUITINDICATION
CARGO COMPT SIDEWALLS
FILTER/DRYERMETERING NOZZLESMETERING NOZZLES
REGULATOR
FWD COMPT
SWITCHESPRESSUREMANIFOLD
TO DISCH
1
TO FWD COMPT
TO FWD COMPTTO AFT COMPT
UNMETERED NOZZLESTO AFT COMPT
UNMETERED NOZZLES
SWITCH
A2
1
DISCH
FWD
MAIN
AFT DISCHDEPR/
ARM
ARM
CARGO FIRE
DISCH
DEPR
FWD
ARMED
ARMED
AFT
ARMED
MAIN
80 LB
80 LB
BOTTLE 2A
BOTTLE 2
HALON
HALON33 LB
BOTTLE 2 MANIFOLD
SQUIB
PRESSURE SWITCHES
PRESSURE SWITCH
DISCHARGE
BOTTLE 1
BOTTLE 1 MANIFOLD
TUBING
HALONPRESSURE
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 104 5/20/13 EFF - ALL
LOWER CARGO FIRE EXTINGUISHING - EXTINGUISHING BOTTLES
Location
The bottles are on the right side of the forward lower cargo compartment behind the cargo compartment lining. You release the velcro and lift the lining up for access.
Physical Description
The bottles contain Halon 1301 fire extinguishing agent pressurized with nitrogen. Bottle 1 (dump) has 80 pounds of Halon. Bottle 2 (metered) has 92 pounds of Halon. Bottle 2A (metered) has 33 pounds of Halon. Each bottle has a nitrogen charge at a pressure of 360 psi.
The fire extinguishing bottles have these components:
• Safety relief and fill port • Pressure switch • Discharge assemblies
Indications
Status messages, maintenance messages, and the DISCH light on the P61 panel show if the bottle pressure is low.
Functional Description
The discharge assembly has an explosive squib that releases the Halon through the discharge port.
The pressure switch monitors the pressure in the bottle and is normally open. When the bottle pressure decreases, the switch closes and sends a signal.
The safety relief and fill port is one fitting on the bottle. The safety relief opens to make sure the bottle does not break if internal pressure is too high.
Filter/Dryer and Regulator Assemblies
A filter/dryer assembly and a regulator assembly are in the metering systems of the forward and aft cargo compartments. The filter/dryer cleans and dries the extinguishing agent. You must replace the filter/dryers after their use. The regulator controls the rate of discharge for bottle 2 and 2A.
Training Information Point
You cannot fill an empty bottle on the airplane. You must replace the bottle. You can weigh the bottles to find the empty/full condition.
WARNING: BE CAREFUL WHEN DISCONNECTING THE HOSE ASSEMBLY FROM THE FIRE EXTINGUISHER BOTTLE. IF THE FIRE EXTINGUISHING BOTTLE IS DISCHARGED, THE TUBING MAY BE PRESSURIZED. RELEASING THE PRESSURE COULD CAUSE INJURY.
WARNING: DO NOT TOUCH THE SQUIB BEFORE DOING THE PROCEDURE FOR DEVICES THAT ARE SENSITIVE TO ELECTROSTATIC DISCHARGE. ELECTROSTATIC DISCHARGE CAN CAUSE THE FIRE BOTTLE TO RELEASE ITS CONTENTS SUDDENLY AND CAUSE INJURY TO PERSONS AND DAMAGE TO EQUIPMENT.
WARNING: BE CAREFUL WHEN YOU MOVE THE FIRE EXTINGUISHING BOTTLE. THE FIRE EXTINGUISHING BOTTLE IS HIGHLY PRESSURIZED AND HAS AN EXPLOSIVE CARTRIDGE AS A COMPONENT. ACCIDENTAL DISCHARGE OF THE FIRE EXTINGUISHING BOTTLE CAN CAUSE INJURY TO PERSONS OR DAMAGE TO EQUIPMENT.
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 105 5/20/13 EFF - ALL
LOWER CARGO FIRE EXTINGUISHING - EXTINGUISHING BOTTLES
122A
DISCHARGESQUIB
DISCHARGEPORT
DISCHARGE
PRESSURESWITCH
PORT
RELIEFVALVE
THERMAL
DISCHARGESQUIB
PRESSURESWITCH
DISCHARGEPORT
THERMALRELIEF VALVE
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 106 5/20/13 EFF - ALL
LOWER CARGO FIRE EXTINGUISHING - EXTINGUISHING BOTTLES (CONT)
Tests
You must remove the fire extinguishing bottle each five years for a hydrostatic test. The date of the last test is on the bottle.
You can do a check of the low pressure switch on the ground. One person must push the button on the low pressure switch housing while a second person monitors the DISCH light on the P8 control stand and the EICAS advisory message. If the DISCH light comes on, the low pressure switch operates correctly. The light goes off when you release the button.
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 107 5/20/13 EFF - ALL
LOWER CARGO FIRE EXTINGUISHING - EXTINGUISHING BOTTLES (CONT)
122A
DISCHARGESQUIB
DISCHARGEPORT
DISCHARGE
PRESSURESWITCH
PORT
RELIEFVALVE
THERMAL
PRESSURESWITCH
DISCHARGEPORT
THERMALRELIEF VALVE
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 108 5/20/13 EFF - ALL
FUNCTIONAL DESCRIPTION BOTTLE DISCHARGE
Cargo Fire Switches
When the FWD ARMED switch is pressed, the following occurs:
• FWD cargo compartment heat valves close. • Fire warning bell is silenced. • FWD Squib test function is disabled. • FWD Cargo Air Conditioning shuts down
When the AFT ARMED switch is pressed, the following occurs:
• Aft and bulk cargo compartment heat valves close. • Fire warning bell is silenced. • AFT squib test function disabled. • The air conditioning packs switch to high flow mode.
Cargo Fire Switches
The cargo fire switch-lights have these functions:
• Compartment fire indication • Enables cargo fire bottle squib operation circuit and gives a circuit ARMED
indication
Bottle Discharge Switch
The bottle discharge switch has two functions, bottle discharge indication and squib operation of the cargo bottles.
When a fire shows in one of the cargo compartments (the red annunciator light in the cargo fire switch is on), you push the cargo fire switch to ARM the discharge circuit. You then push the discharge switch to operate the squib on bottle 1. If the airplane is on the ground, metered bottles 2 and 2A immediately release their contents. If the airplane is in the air, metered bottles 2 and 2A release their contents after 30 minutes.
A bottle discharge indication shows by a pressure switch on the bottle or a pressure switch in the discharge line. You must manually do a reset of the pressure switches in the discharge line after the extinguishing system operates.
To do a test of the pressure switch on the bottle and the discharge indication circuit, you operate the test switch on the bottle pressure switch.
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 109 5/20/13 EFF - ALL
FUNCTIONAL DESCRIPTION BOTTLE DISCHARGE
EICAS COMPUTER
METERED DISCHLINE PRESS SW
FWD CARGO
BTL 1
HOT BAT28V DC
CARGO
LWR CARGOAPU/CARGO FIRE CONTROL (P8)
CARGO BTL 2CARGO BTL 1
P6 MN PWR
DISCH
R MISC ELEC EQUIP PNL (P37)
MD&TINSTR LTS2
1
A A
ARMED
W W
FWD
RR
FWD CARGO
2
PSI
FWD CARGOSQUIB
>300
P
PSI
FWD CARGOSQUIB
>300
P
COMPT BTL 2
LWR CARGO
PSI
FWD CARGOSQUIB
>300
P
COMPT BTL 1
PSI25
PSI25
FEXT DISCHLINE PRESS SW
FWD CARGO
ADVISORY MSG
FEXT
BUS
DISTR
BTL 2
HOT BAT28V DC
CARGOFEXT
BUS
A
A
FWD CARGOCOMPT SMOKEDETECTION
1
FIRE SW
1
B
B
34
MUST PUSHPUSH TO TEST
TO RESET
BTL DISCH SWK2
K1
4 4
3
4
3
LWR CARGOCOMPT BTL 2A
NOTE: FWD CARGO COMPARTMENT SHOWN, AFT IS SIMILAR
FWD COMPT30 MIN
LOCK-IN RLY
TD
AIR
SYS NO. 2AIR GND RLY
GND
BTL 2ADISCH RLY
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 110 5/20/13 EFF - ALL
BOTTLE 2 AND 2A DISCHARGE CIRCUIT - FUNCTIONAL DESCRIPTION
Bottle Discharge Circuit for Bottles 2 and 2A
After you push the discharge switch, the squib on bottle 1 operates, and the fwd compartment lock-in relay energizes. Bottle 1 releases its contents immediately.
Bottles 2 and 2A start a metered discharge immediately if the airplane is on the ground. If the airplane is in the air, the metered discharge starts after a 30-minute delay.
A bottle discharge indication shows by a pressure switch on the bottle or a pressure switch in the discharge line.
You must manually do a reset of the pressure switches in the discharge line after the extinguishing system operates. To do a test of the bottle pressure switches and the discharge indication circuit, you push the test buttons on the bottle pressure switches.
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 111 5/20/13 EFF - ALL
BOTTLE 2 AND 2A DISCHARGE CIRCUIT - FUNCTIONAL DESCRIPTION
FWD GALLEY CHILLER, AND FWD/MID GALLEY PWR
MD&TINSTR LT
321
INPUTS TO PUT OFF RECIRC FANS, CARGO HEAT,
EICAS COMPUTER
METERED DISCHLINE PRESS SW
FWD CARGO
BTL 1
C781
HOT BAT28V DC
CARGO
LWR CARGOAPU/CARGO FIRE CONT (P8)
FWD COMPT
CARGO BTL 2CARGO BTL 1
P6 MN PWR30 MIN
DISCH
R MISC ELEC EQUIP PNL (P37)A A
ARMED
W W
FWD
RR
LOCK-IN RLYFWD CARGO
3
2
PSI
FWD CARGOSQUIB
>300
P
PSI
FWD CARGOSQUIB
>300
P
COMPT BTL 2
LWR CARGO
PSI
FWD CARGOSQUIB
>300
P
COMPT BTL 1
PSI25
PSI25
FEXT DISCHLINE PRESS SW
FWD CARGOAIR
ADVISORY MSG
FEXT
BUS
DISTR
BTL 2
C773
HOT BAT28V DC
CARGOFEXT
BUS
A
A
B
B
FWD CARGOCOMPT SMOKEDETECTION
1
FIRE SW
1
C
C
SYS 2
GND
BTL 2ADISCH RLY
BTL DISCH SWK2
K1
TD
LWR CARGOCOMPT BTL 2A
AIR GND RLY
NOTE: FWD CARGO COMPARTMENT SHOWS, AFT IS SIMILAR
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 112 5/20/13 EFF - ALL
FIRE PROTECTION - OPERATIONAL TEST
General
The operational tests for the fire extinguishing system are cargo squibs and engine and APU squibs.
You can do a squib continuity test of all bottles from the squib test panel. The squib test panel is on the P61 panel.
Cargo Squibs
The cargo squib test supplies current to the squibs on the cargo compartment fire extinguisher bottles.
Squib test switches on P61 give an easy test of all six squibs, two on each bottle. Power is from the 28v dc hot battery bus. This test makes sure there are no open circuits in the cargo compartment fire extinguishing squibs and the related wiring. Green lights show squib circuit continuity.
The squib operates with 3.5 amps. The test current is 50 ma.
The voltage drop across the test lamp does not let enough current flow to fire the squib. You must make sure the replacement lamps are the correct type and value. Accidental squib operation and bottle content release can occur.
Engine Squibs
The engine squib test supplies current to the squibs for the two engine fire extinguishing bottles.
You push these two switches on the P61 panel to do a test of the squibs:
TEST 1 - does a test of the two squibs on bottle 1TEST 2 - does a test of the two squibs on bottle 2
A successful test shows when the ENG L and R green lights come on.
APU Squib.
To do a test of the squib on the APU fire extinguishing bottle, you push the TEST 1 squib test switch on the P61 panel.
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 113 5/20/13 EFF - ALL
FIRE PROTECTION - OPERATIONAL TEST
DISCH
APU BTLDISCH
APU
BOTTLEDISCHARGED
APUSHUTDOWN
APU BOTTLEDISCHARGE
FLIGHT DECKCALL
FLIGHTINPH
SERVICEINPH
EMER EXITLT TEST
WHEELWELLLIGHTS
OFF
APU FIREFIRE BOTTLE
ARMED
APU FIREWARNINGHORN
RS
LS
REMOTE APUCONTROL PANEL
(P40)
LEFT
1 2DISCH
1 2DISCH
THGIR
R ENGOVHT2 DISCH
ENG BTL1 DISCH
ENG BTLOVHTL ENG
ENG FIRE
BOTTLE
APU/CARGO FIRE CONTROL PANEL
APU BOTTLE
ENG 2
CARGOBOTTLE
CARGOBOTTLE 2
ALL MESSAGES AREADVISORIES
EICASCARGOBOTTLE 1
2A
AIR
GND30-MINDELAY
ENG BTL 1 (C)ENG BTL 2 (C)
CARGO BTL 1 (C)CARGO BTL 2 (C)
APU BTL (C)CONTROL PANEL (P8)
BOTTLEENG 1
SQUIB TEST PANEL (P61)
2 2A1
AFT
FWDTEST 1
TEST 2
CARGO2
APU
SQUIB TEST
LENG
1RTEST
FWD
MAIN
AFT DISCHDEPR/
ARM
ARM
CARGO FIRE
DISCH
DEPR
FWD
ARMED
ARMED
AFT
ARMED
MAIN
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 114 5/20/13 EFF - ALL
WHEEL WELL FIRE DETECTION - INTRODUCTION
Purpose
The wheel well is protected from an overheat condition caused by hot landing gear brakes or tire fires.
Physical Description
Each element has a nickel wire around it and insulating material contained in the steel tube. The insulating material is heat sensitive and becomes more conductive when the temperature increases.
Location
The detector is a single loop detector on the ceiling of the wheel well bay.
Two sensors in series are attached to the top of each main wheel well.
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 115 5/20/13 EFF - ALL
WHEEL WELL FIRE DETECTION - INTRODUCTION
WELL FIRE DETECTORSSINGLE LOOP WHEEL
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 116 5/20/13 EFF - ALL
WHEEL WELL FIRE DETECTION - GENERAL DESCRIPTION
General
Two sensor loops are in the top of each main wheel well.
The wheel well fire detector is a single Loop Fenwal detection system. A signal from any wheel well fire detector element goes to the duct leak and wheel well fire card in the P54 fire protection card file.
The card causes flight compartment indications of a wheel well fire.
You do a test of the wheel well fire detection system from a test switch on the fire/overheat test panel on P8.
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 117 5/20/13 EFF - ALL
WHEEL WELL FIRE DETECTION - GENERAL DESCRIPTION
FAIL
ENG/APUFIRE/OVHT TEST
CARGOWELLWHL SYS FAIL
P-RESET
P7
CAUTION
WARNING
DISCRETE WARNINGDISPLAY (P1-3)
CABIN
PULL UP DISCA/P
OVSPD
CONFIGFIRE
ALT
FIRE/OVERHEAT TEST PANEL (P8)
WHEEL WELL FIRE (A)
FIREWHL WELL
TEMPBRAKE
&
BELL/CHIMEAURAL
MASTERWARNINGMODULES
ELECTRONICSUNIT (P51)
WARNING
DET LOOPWHEEL WELL FIRE
TEST
L(R) EICASCOMPUTERS
CARD FILE (P54)FIRE DETECTION
DUCTLEAK &WHEELWELLFIRECARD
EICAS DISPLAY UNIT (P2)
AURALWARNINGSPEAKER
(WARNING)
(E8)
EDGETRAILING
EDGELEADING
OFF
270KRETRACTUP
TEMP SEL
1 2CLBTOGA
CON CRZ
TAIL SKID
RAEG
NOSESROOD
LEFT RIGHT
P3-1
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 118 5/20/13 EFF - ALL
WHEEL WELL FIRE DETECTION - FUNCTIONAL DESCRIP-TION
General
When there is a fire and the temperature along a detector gets to 400F (204C), the resistance between the nickel wire and the grounded steel tube decreases.
The duct leak and wheel well fire card in the P54 card file senses this decrease.The card gives the flight compartment indications of a wheel well fire.
Operation of the wheel well test switch makes a ground for each detector loop and does a check of the continuity of the detection circuit. If the circuit has continuity, wheel well indications show.
A fault (short circuit) gives the same indications as a wheel well fire.
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 119 5/20/13 EFF - ALL
WHEEL WELL FIRE DETECTION - FUNCTIONAL DESCRIPTION
DUCT LEAK AND WHEEL WELLFIRE CONTROL CARD (P54)
DETCKT
FIREWHEEL WELL
L/R EICAS
UNITELECTRONICSWARNING
P3
P1
MD&T
MD&T
WHEEL WELL
(P37)FIRE IND
ELEM SENSORELEM SENSOR
ELEM SENSOR
RIGHT WHEELWELL DET
LEFT WHEELWELL DET
ELEM SENSOR
RIGHT WHEEL
LEFT WHEEL
WELL DET
WELL DET
WHEEL WELLTEST (P8)
P11
28V DCBAT BUS
WW FIREIND/TEST
P11
DUCT LEAKWW FIRE
STBY BUS115V AC
COMPUTER (E8)
FIREWHL WELL
FIRE
HEAT SENSITIVEELECTRICALLYCONDUCTIVE MATERIAL
CENTRALCONDUCTOR
STEEL TUBEOUTER (GROUNDED)CONDUCTOR1/16 INCH
CONNECTOREACH END
DUCT LEAK DETECTION SENSOR(TYPICAL)
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 120 5/20/13 EFF - ALL
WING AND BODY DUCT LEAK DETECTION - INTRODUCTION
Purpose
The detector loop finds an increase in temperature around the pneumatic duct.
Physical Description
The duct leak detector is a Fenwal type detector with thermistor material in the tube. The detector has two conductors. The center conductor connects to the detector card, and the outer conductor (detector case) connects to airplane ground. The temperature sensitive thermistor material is between the two conductors. The wing duct leak detectors and body duct leak detectors are similar.
Location
The detector loop is parallel to the pneumatic ducts from the engine strut to wing joint to the left or right isolation valve and between the left and right isolation valves. The loop is also on the body pneumatic duct from the center isolation valve to the APU shutoff valve.
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 121 5/20/13 EFF - ALL
WING AND BODY DUCT LEAK DETECTION - INTRODUCTION
WING DUCT LEAKDETECTORS
WING DUCT LEAKDETECTORS
BODY DUCT LEAKDETECTORS
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 122 5/20/13 EFF - ALL
WING AND BODY DUCT LEAK DETECTION - DETECTORS
Purpose
Wing duct leak detectors monitor the pneumatic distribution ducts in the wing leading edges into the air conditioning compartments to the left and right isolation valves.
The body duct leak detectors extend from the center isolation valve to the APU fire wall.
Physical Description
The wing and body detection sensors (elements) are in a single loop circuit.Each element has a nickel wire and insulating material contained in a steel tube.
The insulating material is heat sensitive and becomes more conductive with a temperature increase.
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 123 5/20/13 EFF - ALL
WING AND BODY DUCT LEAK DETECTION - DETECTORS
HEAT SENSITIVEELECTRICALLYCONDUCTIVE MATERIAL
CENTRALCONDUCTOR
1/16 INCH
CONNECTOREACH END
DUCT LEAK DETECTION SENSOR(TYPICAL)
OUTER CONDUCTOR(GROUNDED)
OUTER CONDUCTOR(GROUNDED)
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 124 5/20/13 EFF - ALL
WING AND BODY DUCT LEAK DETECTOR - FUNCTIONAL DESCRIPTION
General
When a segment of a duct leak detector gets to the overheat temperature, an alarm signal goes to the detection circuit on the duct leak overheat and wheel well fire card in the P54 card file. The detection circuit receives the signal and makes an alarm signal to put on the DUCT LEAK light on the P5 panel and the caution messages on EICAS in the flight compartment. When the duct leak detector decreases to the reset temperature, the alarm signal stops.
Training Information Point
The duct leak test switch connects a ground for each detector loop and does a check of the continuity of the detection circuit. If the circuit has continuity, duct leak indications show.
A fault (short circuit to ground) gives the same indication as overheat condition.The test only operates on the ground.
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 125 5/20/13 EFF - ALL
WING AND BODY DUCT LEAK DETECTOR - FUNCTIONAL DESCRIPTION
BLEED AIR
DUCT LEAK AND
BODY DUCT LEAK
DUCT LEAK TEST
TEST PANEL (P61)(L WHEELWELL)
WING BLEED DUCT
WING BLEED DUCT
P11 PANELDUCT LEAKWW FIRE
L/R EICAS CMPTR
STBY BUS115V AC
R BLD DUCT LEAKL BLD DUCT LEAK
(L WING)(L WINGENG STRUT)
(AFTCARGO COMPT)
(ADP(FUSELAGETAIL)
GND
AIR
SYS 1 AIR/GND(P36)
(R WING) (R WINGENG STRUT)
CKTDET
DETECTORS - RIGHT
DETECTORS - LEFT
WHEEL WELL FIRE CARD(P54)
COMPT)
CKTDET
CKTDET
SUPPLY (P5)
MD&T
MD&T
MD&TOFF
DUCT LEAK
LEAKDUCT
LEAKDUCT
LEAKDUCT
40
60 80
20 0
DUCTPRESS
PSIRL
R ISLN
VALVE
C ISLN
UCT
D LEAK
F
OF
L ENG
L ISLN
VALVE
LEAKDUCT
BLEED
R ENGAPU
ADP
FFO
VA
EVL
OVHT
E
VALV
LEAKDUCT
BLEED
OVHT
DUCT LEAK
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 126 5/20/13 EFF - ALL
WING AND BODY DUCT LEAK DETECTION - STRUT OVER-HEAT DETECTORS
Purpose
The strut overheat thermal switches monitor the temperature in the engine strut. A leak in the pneumatic duct causes an overheat condition.
Physical Description
The strut overheat detectors are thermal switches that connect in a series configuration. The switch connects a ground when the temperature gets to a set level.
Location
There are two strut overheat thermal switches in each engine strut adjacent to the PRSOV.
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 127 5/20/13 EFF - ALL
WING AND BODY DUCT LEAK DETECTION - STRUT OVERHEAT DETECTORS
THERMALSWITCHMATERIAL
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 128 5/20/13 EFF - ALL
STRUT OVERHEAT DETECTORS - FUNCTIONAL DESCRIP-TION
Functional Description
When the temperature in the strut gets to a preset value, the strut thermal switch closes and gives an input to the bleed air control card. If the input signal is still there after a five-second time delay, the card latches and gives an output.
Output 1 shows the duct leak annunciator light on P5. Output 2 sends the EICAS message, L/R STRUT DUCT LEAK.
In the pneumatic system, the bleed air control card commands the high pressure shutoff valve and pressure regulating valve to close. This stops engine bleed air. If the pressure regulating valve or high pressure shutoff valve fails to close, the bleed annunciator light on the air supply panel comes on and the EICAS message of L/R ENG PRV or L/R ENG HPSOV shows.
To reset the system, cycle the engine bleed air supply switch.
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 129 5/20/13 EFF - ALL
STRUT OVERHEAT DETECTORS - FUNCTIONAL DESCRIPTION
LATCHRESET
BLEED AIRSUPPLY (P5)
MD&T
L WING ENGINE STRUT
L/R EICAS
R STRUT
L STRUT
ELECTRICAL SYSTEM CARD FILE (P50)
ON
AIR SPLY
OFF
L ENG BLDL BLEED AIR CONTROL PC
ALARM 2
ALARM 11
28V DCR BUS
P11 CB PANEL
R AIRSUPPLY ENG
ALARM 2
ALARM 11
FAILURE OF PRV OR HPSOV TO CLOSE SHOWS BY BLD LT AND RESPECTIVE ENG PRV FAIL OR ENG BLD VAL EICAS MESSAGESENDS CLOSE COMMAND TO HIGH PRESSURE SHUTOFF VLV AND PRESSURE REGULATING VLV. TO RESET, CYCLE BLEED SW1
DCT LEAK B
DCT LEAK B
CMPTR (E8)
BLEED CONT
28V DCR BUS
R AIRSUPPLY ENGBLEED CONT
SPLY PNL (P5)BLEED AIR
SPLY PNL (P5)BLEED AIR
R BLEED AIR CONTROL PC
RESET
LATCHRESET
PWR SPLY V
5 SEC
RESET
5 SEC
STRUT LEAK
FUEL QTYOFF
TEST PANEL (P61)
DUCT LEAKDET SNSR
K143 SYS 1AIR/GND (P36)
GND
R WING ENGINE STRUT
DUCT LEAKDET SNSR
DUCT LEAKDET SNSR
DUCT LEAKDET SNSR
MD&T
ON
AIR SPLY
OFF
R ENG BLD
PWR SPLY V
LEAKDUCT
LEAKDUCT
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 130 5/20/13 EFF - ALL
WING AND BODY DUCT LEAK DETECTION & INTRODUCTION
Purpose
The wing and body duct leak detection system monitors the pneumatic ducts from the APU to the center isolation valve and the engine ducts from the bleed valve to the left or right isolation valve for leaks.
The detection of a leak shows on the pneumatic panel and makes an EICAS CAUTION message.
Purpose
The detector loop finds an increase in temperature around the pneumatic duct.
TRAINING MANUALFOR TRAINING PURPOSES ONLY
B767-3S2F ATA 26-00 Page - 131 5/20/13 EFF - ALL
40
60 80
20 0
DUCTPRESS
PSIRL
R ISLN
VALVE
C ISLN
UCT
D LEAK
F
OF
L ENG
L ISLN
VALVE
LEAKDUCT
BLEED
R ENGAPU
ADP
FFO
VA
EVL
OVHT
E
VALV
LEAKDUCT
BLEED
OVHT
FIRE PROTECTION
AIR SUPPLY PANEL (P5)
ELECTRICAL SYSTEMCARD FILE (P50)CARD FILE (P54)
BODY DETECTIONSENSOR LOOP
WING DETECTORSENSOR LOOPS
L BLD DUCT LEAKR BLD DUCT LEAKBODY DUCT LEAKL STRUT DCT LEAKR STRUT DCT LEAK
EICAS DISPLAY(CAUTION LEVEL B)