DISTRIBUTED BY:3.09
NWORLD WELDING MACHINESWORLDWORLDsrl
BLUE SHARK 141 - 161 - 201 - 253 - 403The Blue Shark is an inverter generator designed mainly for welding with a cellulose electrode.Its principal characteristics are: high resistance and reliability, welding of all types of electrode (aluminium and cellulose), arc-force, TIG welding with lift start, remote control, designed and made in accordance with standard EN 60974/1 - EN 60974-10.
Specification
POWER ARC 303 - 403 - 503 - 603 - 803The Power Arc welding rectifiers have been designed to correspond to the maximumexpectations in strengthens, operative results and liability. The zinc-aluminium anticorrosivehousing, the copper winding transformer in H class and the rectifier (absolutely protected fromoverheating) are being chosen to resist hard risk environmental conditions. Its characteristic: • Arc-force device • Anti stick device• Hot start automatic to improve the trigger with difficults electrodes• Electronic welding current regulation• The EL-ARC can weld in TIG with slightly rubbing or by adding a TIG AID: the 606 and 806 version are excellent for digging. Allows to obtain quality results also with the most difficult cellulosic and basic electrodes.
1.6 - 8
Specification P-ARC 303 P-ARC 403 P-ARC 503 P-ARC 603 P-ARC 803
3 Phase Input (V 50/60 Hz)
Installed Power (Max. kVA)
Open Circuit Voltage (V)
Current Range (A)
Duty Cycle at (A 100%)
(A 60%)
(A 35%)
Electrodes
Standards
Protection Class
Insulation Class
Dimensions (mm)
Weight (kgs)
Order No.
18.4
70
5 - 300
177
230
300
1.6 - 6
142
2340910303
22.3
70
5 - 400
235
305
400
168
2340910403
32
60
5 - 500
294
383
500
198
2340910503
56.5
87
5 - 800
473
610
800
1.6 - 16
230
2340910803
38
75
5 - 600
387
500
600
203
2340910603
EN 60974-1 • EN609974-10
23
H
500 x 870 x 670
230/400
BS 141 BS 161 BS 201 BS 253 BS 403
1 Phase Input (V 50/60 Hz)
3 Phase Input (V 50/60 Hz)
Installed Power (Max. kVA)
Open Circuit Voltage (V)
Current Range (A)
Duty Cycle at (A 100%)
(A 60%)
(A 40%)
Standards
Protection Class
Insulation Class
Dimensions (mm)
Weight (kgs)
Order No.
-
5.1
56
5 - 140
100
-
140
132 x 290
x 203
5.5
2340911141
-
6.9
56
10 - 160
124
160
-
152 x 375
x 232
7.5
2340911161
-
8.9
56
10 - 200
155
200
-
152 x 375
x 232
8
2340911201
-
17.9
67
40 - 400
310
400
-
260 x 515
x 370
230
2340911403
-
10.3
54
20 - 250
190
250
-
204 x 480
x 303
203
2340911253
EN 60974-1 • EN609974-10
23 - S
F
230 ±15%
380 ±15%
BLUE TIG DC 273 - 403 - 503The thyristor controlled Blue TIG DC generators have the necessary features for professional welding in TIG DC (mild steel, stainless steel, bronze+copper) and MMA (with flux cored rutil andbasic electrodes). This equipment guarantees a minimum current of 5A in TIG welding and striking that is always ready thanks to its powerful high-frequency. Its characteristic : high frequency striking, current slope-up and slope-down, post-gas time, setting pulsed.
Specification
TIG WLX 161 DC - 201 DC - 263 DC - 323 DCThe Inverter technology of TIG WLX gives this welding machine professional calibre and weldingquality. Its principal characteristics are: compactness and reliability, functions selector (electrode,2T, 4T, pulse, resetting), remote control, slope up and slope down, pulse frequency adjustment,post-gas time adjustment, basic current adjustment, HF or LIFT enabling, digital Voltmeter andAmpèremeter, designed and made in accordance with standard EN 60974/1- EN 60974 -10.
Specification
BLUE TIG DC 273 BLUE TIG DC 403 BLUE TIG DC 503
3 Phase Input (V 50/60 Hz)
Installed Power (Max. kVA)
Open Circuit Voltage (V)
Current Range (A)
Duty Cycle at (A 100%)
(A 60%)
(A 35%)
Standards
Protection Class
Insulation Class
Dimensions (mm)
Weight (kgs)
Order No.
15.2 60
5 - 250148190250
530 x 780 x 83098
2340920273
22.370
5 - 400235305400
530 x 890 x 860163
2340920403
3270
5 - 500294383500
530 x 890 x 860193
2340920503
EN 60974-1 • EN609974-1023H
230/400
WLX 161DC WLX 201DC WLX 263DC WLX 323DC
1 Phase Input (V 50/60 Hz)3 Phase Input (V 50/60 Hz)Installed Power (Max. kVA)Open Circuit Voltage (V)Current Range (A)Duty Cycle at (A 100%) (A 70%) (A 60%) (A 40%)StandardsProtection ClassInsulation ClassDimensions (mm)Weight (kgs)Order No.
-3.5 100
5 - 160125
-160
-
8.82340921161
-4.185
5 - 200140
--
200
180 x 405 x 22510.25
2340921201
-
6.885
5 - 250210250
--
15.502340921263
-
15.285
5 - 320265320
--
180 x 405 x 38516.8
2340921323
EN 60974-1 • EN609974-1023-S
F
400230
DISTRIBUTED BY:3.10
NWORLD WELDING MACHINESWORLDWORLDsrl
Specification
Specification
LFX 201 AC/DC LFX 323 AC/DC1 Phase Input (V 50/60 Hz)3 Phase Input (V 50/60 Hz)Installed Power (Max. kVA)Open Circuit Voltage (V)Current Range (A)Duty Cycle at (A 100%) (A 70%) (A 40%)StandardsProtection/Insulation ClassDimensions / Weight (mm/kg)Order No.
230-
6.2 95
5 - 200140
-200
2340922201
-40015.595
5 - 320265320
-
234092323
EN 60974-1 • EN609974-1023-S/ F
235 x 425 x 385/ 20.5
BC 301 BC 303 BC 353 BC 403 BC 503
1 Phase Input (V 50/60 Hz)
3 Phase Input (V 50/60 Hz)
Installed Power (Max. kVA)
Fuse Delayed Action (A)
Open Circuit Voltage (V)
Adjustment Positions (N˚)
Current Range (A)
Duty Cycle at (A 100%)
(A 60%)
(A 40%)
(A 30%)
Wires (mm)
Standards
Protection/Insulation Class
Dimensions (mm)
Weight (kgs)
Order No.
-
11
17 - 34
14
155
200
-
300
0.8 - 1.6
75
2340930301
-
12.3
17 - 41
20
177
230
300
-
0.8 - 1.2
90
2340930303
-
15.3
16/10
17 - 43
30
40 - 350
207
267
350
-
100
2340930353
-
17.6
25/16
17 - 44
30
40 - 400
237
306
400
-
103
2340930403
-
26
35/20
17 - 51
30
50 - 500
296
400
500
-
0.8 - 2.4
110
2340930503
EN 60974-1 • EN609974-10
23/H
530 x 870 x 830
230/400230
0.8 - 2.0
63
40 - 300
TIG LFX201 AC/DC - 323 AC/DCThe NEW TIG GENERATION LFX AC/DC welding power sources developed by NWorld aninnovative microprocessor that present to the operator all the features and benefits required toperform very high quality welding, stainless/steels and alumunium and its alloys. The immediateresponse if the new powerful microprocessor allows for a perfect start to be achieved every time.Designed and made in accordance with standard EN 60974/1 - EN 60974 - 10
BLUE COMPACT 301 - 303 - 353 - 403 - 503The Blue Compact equipment are manufactured to meet the small-medium mill work needs.The Blue Compact is equipped with an incorporated wire feeding system. Speed regulation 2/4 times setting and spot welding.
DISTRIBUTED BY:3.11
NWORLD WELDING MACHINESWORLDWORLDsrl
BLUE STAR 400 - 500 - 600 - 700The thyristor Blue Star model are three phase machines with electronic current control. They aredesigned for MIG-MAG welding with solid or flux cored wires of steel, stainless steel, alumimiumand copper.
POWER MIG 260 - 330 - 430The thyristor POWER MIG model are three phase machines with electronic current control. Theyare designed for MIG-MAG welding with solid or flux cored wires of steel, stainless steel,aluminium and copper.
Specification
Specification
BS 400 BS 500 BS 600 BS 700
3 Phase Input (V 50/60 Hz)Installed Power (Max. kVA)Open Circuit Voltage (V)Current Range (A)Duty Cycle at (A 100%) (A 60%)Wires (mm)StandardsProtection ClassInsulation ClassDimensions (mm)Weight (kgs)Order No.
22.9
40 - 400310400
0.8 - 1.6
1402340933400
31.5
50 - 500387500
0.8 - 2.0
1662340933500
40.2
50 - 600465600
0.8 - 2.4
2022340933600
47.266
50 - 700542700
0.8 - 2.4
2202340933700
EN 60974-1 • EN609974-1023H
500 X 890 X 860
230/400
60
PMIG 260 PMIG 330 PMIG 430
3 Phase Input (V 50/60 Hz)Installed Power (Max. kVA)Open Circuit Voltage (V)Current Range (A)Duty Cycle at (A 100%) (A 60%) (A 35%)Wires (mm)StandardsProtection ClassInsulation ClassDimensions (mm)Weight (kgs)Order No.
10.3 42
40 - 260150191260
0.8 - 1.2
772340934260
15.744
40 - 330200260330
0.8 - 1.6
1032340934330
27.447
40 - 430255300430
0.8 - 2.0
1222340934430
EN 60974-1 • EN609974-1023H
530 x 870 x 830
230/400
DISTRIBUTED BY:3.12
NWORLD WELDING MACHINESWORLDWORLDsrl
DISTRIBUTED BY:3.13
NWORLD WELDING MACHINESWORLDWORLDsrl
Specification
Specification
POWER PULS 400 POWER PULS 500 POWER PULS 600
3 Phase Input (V)Frequency (Hz)Installed Power (Max. kVA)Open Circuit Voltage (V)Current Range (A)Duty Cycle at (A 100%) (A 60%)Wires (mm)StandardsProtection/Insulation ClassDimensions (mm)Weight (kgs)Order No.
22.9 60
40 - 400310400
0.8 - 1.6
1402340935400
31.560
50 - 500387500
0.8 - 2.0
1662340935500
40.260
50 - 600465600
0.8 - 2.4
2022340935600
EN 60974-1• EN609974-10 • EN 60974-7-S23/H
420 x 650 x 780
230/40050/60
BSW 503 P
3 Phase Input (V)Frequency (Hz)Installed Power (Max. kVA)Current Range (A)Duty Cycle at (A 100%) (A 60%)Wires (mm)Standards Protection/Insulation ClassDimension (mm)Weight (kg)Order No.
3 x 400 ±10%50/6025,4
20-500440500
0.6 - 1.6EN 60974-1 • EN 60974-10
23S/ H530 x 900 x 830
732340950503
POWER PULS 400 - 500 - 600The POWER PULS equipment are three phases generators with thyristor controlled welding tension, through an integrated impulses system selected between 50/100/150 Hz, continuously or switched, that consent to obtain all the benefits offered by the pulsed are: sprays absence, thin metal sheet welding of (1,5 mm thickness) aluminium and stainless steel with excellent finishing of the welding beads.Furthermore, these generators are equipped with an electronic device in order to compensate the variations of the tension in net of ±10%. These generators are indicated for semiautomatic welding for flux cored or tubular wire, steel, stainless steel, aluminium with MIG/MAG, Pulsed procedure and in MMA under request
BLUE SYNERGIC WORLD 503 PThe Blue Synergic World is composed of an Inverter Power Source with separate wire feeding device. Reliability, low weight and compact dimensions, together with absolute welding quality, make Blue Synergic World generators the peak machines in the NWorld range.
NWORLD WELDING MACHINESWORLDWORLDsrl
DISTRIBUTED BY:3.14
BLUE CUTBLUE CUT machines are three phases cutting equipment. Plasma Arc Cutting is a processwhich severs metal by melting a localized area with the heat of a constricted are removes the molten material within a high velocity jet of hot, ionized gas issuing from the orifice. In compari-son with the oxyacetylene cutting process is much quicker, besides, the thermal alterations ofthe metal along the cut edges are smoother. So it is used to cut aluminium and its alloys, stain-less steel, copper, brass. Besides, it is supplied with an exclusive device for cutting on grilled orperforate plate, keeping cutting continuous without having to reset the torch button.
HYPER CUT The three-phase HYPER CUT generator, developed on the lastest evolution of thyristor technology, guarantees reliability and safety in all job conditions. Thanks to the electronic con-trol of the cutting current it is always possible to set up the most correct parameters, so as toassume elevated characteristics of cut in the various applications. The Hyper Cut allows to usetorches of various power, changing automatically the current scale in order to adapt itself to theemployed torch. HF Ignition and automatic turning off when the cutting arc is stabilized. Up slo-pe adjustment, control panel with automatic indicator for the correct tip diameter to use in func-tion of the torch and the cut current pre-adjusted.
Specification
Specification
BC 53 BC 143 BC 163BC 103BC 73
3 Phase Input (V)
Frequency (Hz)
Installed Power (Max. kVA)
Adjustment Position (N˚)
Current Range (A)
Duty Cycle at (A 60%)
Max. Cutting
Thickness (mm)
Standards
Protection Class (mm)
Dimensions (mm)
Weight (kgs)
Order No.
8
25 - 50
50
8 -10
65
2340940053
12
40 - 70
70
18 - 20
360 x 560 x 780
100
2340940073
15
50 - 100
100
25 - 30
107
234090103
24
60 - 140
140
35 - 40
122
234090143
31
100 - 160
160
45 - 50
140
234090163
EN 60974-1 • EN609974-10 • EN 60974-7-S
23
230/400
50/60
420 x 560 x 780
2
HC 63E HC 83E HC 133E
3 Phase Input (V)Frequency (Hz)Installed Power (Max. kVA)Current Range (A)Duty Cycle at (A 50%)Max. CuttingThickness (mm)StandardsProtection Class (mm)Dimensions (mm)Weight (kgs)Order No.
14.125 - 60
608 -13
652340941063
18.625 - 80
8020 - 25
1002340941083
27.225 - 120
12035 - 40
122234094133
HC 163E
37.225 - 160
16050 - 55
140234094163
EN 60974-1 • EN609974-10 •EN 60974-7-S23
420 x 650 x 780
230/40050/60
DISTRIBUTED BY:3.15
W POWER 5 - 8This unit is particularly well suited to cool MIG/MAG and TIG torches; the unit is equipped with ahandle for easy transport, a cable for rapid connection to the 220V mains supply and can be mounted on any generator. On request, this unit can be equipped with a flow switch that controlthe flow of the cooling liquid when combined with an electronic card. A decrease of the cooling flow beyond a given limit pre-set in the factory causes the generator to shut-down and triggers asignal to indicate insufficient cooling liquid flow.
Specification
Specification
W POWER 8W POWER 5
Dimensions (mm)Weight (kgs)Order No.
385 x 370 x 62014
2340970005
250 x 250 x 63016
2340970008
5m Cable10m Cable20m Cable30m Cable40m Cable50m Cable
Order No.
234099910523409991102340999120234099913023409991402340999150
SPECIAL WIRE FEEDERTo be connected to any Electrode MMA - CC - CV Welding machine for solid and turbular wire gasshielded or glasses turbular wire 4 Rolls Wire Drive 0.8 - 1.6mm
Features :• ON/ OFF light • Switch ON/ OFF• Switch manual-automatic (2T-4T) • Switch for gas control• Potensiometer for wire speed • Burn-back• Microprocessor for control • Earth cable 4m• Aircooled or watercooled
Optional : • Gas flow meter • Digital V & A meter
Weight : 12,8 kgsDimension : 600 x 220 x 420 mm
REMOTE CONTROL
Order No. :2340939072
NWORLD WELDING MACHINESWORLDWORLDsrl