+ All Categories

Download - Broucher Ceiling

Transcript
Page 1: Broucher Ceiling

INTERARCH BUILDING PRODUCTS PVT. LTD.AN ISO 9001-2000 COMPANY

Central Marketing OfficeB-30, Sector 57, NOIDA - 201 301, INDIA

Tel.: 0120 - 4170200/2581300/2581029, Fax : +91-120-2581017E-mail: [email protected] | www.interarchbuildings.com

NNOVATE NITIATE NTEGRATE

CEILINGS

Page 2: Broucher Ceiling

Interarch UNIT 1, Greater NOIDA, UP, IndiaInterarch UNIT 1, Greater NOIDA, UP, India

Interarch Building Products Pvt. Ltd. commenced

operations in 1984, and pioneered the high-end metal

interior products market in India. Today, 25 years later,

Interarch is proud to be the largest Turnkey

Pre-Engineered Steel Construction Solution provider in

India with more than 40% market share in this segment.

Interarch has been a large and integrated manufacturer of

Pre-Engineered Building Systems with in-house Design,

Manufacture, Logistics, Supply and Project Execution

capabilities.

Introduction

NNOVATE NITIATE NTEGRATE

Page 3: Broucher Ceiling

®TRAC Ceilings

®INTERARCH introduced TRAC lineal metal ceilings in 1984. Today,

INTERARCH is the largest manufacturer of metal building systems in India,

and the product range includes pre-engineered steel buildings, metal

roofing and cladding systems, metal and gypsum suspended ceilings and

window covering products. All manufacturing facilities are ISO 9001

certified by Underwriters Laboratories Inc., USA.

® TRAC ceiling systems set the trend and command a very high market share ®in India. The TRAC range of metal and Glass Reinforced Gypsum ceilings

are specially designed for the Indian market, taking into account of building

design, construction practices and weather conditions.

150C Ceiling System

200F Ceiling System

Curved Panel 84R

Inside Curve

84R Curved Panel Ceiling

Ceiling: Functional Features

CONCEALING SERVICES

Ceilings are primarily installed to conceal services such as HVAC ducting and

lighting. The covering up of services necessitates access to the ceiling

plenum. Accessibility to the ceiling plenum for maintenance is the most

important factor while selecting a suspended ceiling system.

84C Ceiling System

GRG Open Cell Ceiling

Panel Splice

Carrier Splice

®All TRAC ceilings are designed to allow easy access. Panels or tiles may be

lifted out or clipped off for maintenance or installation of concealed services.

AESTHETICS

Ceilings are often provided to create attractive interiors. ceilings

offer several options to the designer to match aesthetics with function.

®TRAC

ACOUSTICS

Suspended acoustical ceilings serve to provide sound absorption on the

most useful surface in a room. They help in reducing reverberant sound ® intensity within a room. TRAC ceilings are the most efficient sound

absorbing ceilings available in the market today.

Human activity in offices and large public spaces generates noise resulting in

reduced work efficiency. Acoustical (sound absorbing) ceiling systems help in

reducing build-up of reverberant noise because of their excellent sound

absorbing properties. This leads to a better working environment and

reduced annoyance due to high noise levels.

Main Runner

Outside Curve

Hook & Butterfly Clip

GRG Open Cell Ceiling

Cross Tee

1 2NNOVATE NITIATE NTEGRATE

Page 4: Broucher Ceiling

ACOUSTICS

SOUND ABSORPTION

Noise is major concern when designing indoor spaces. Room sound

absorption is one of the most important factors in controlling built-up

reverberant noise and in reducing sound transmission between rooms.

When specifying the ceiling, the architect should ensure that the

specifications incorporate acoustic performance requirements.

The sound absorbing efficiency of material is designated by its sound

absorption coefficient (a). This is usually measured and reported in octave

bands over the frequency range of 125-4000 Hz, together with the Noise

Reduction Coefficient (NRC), which is the average of the sound absorption

coefficient at 250, 500, 1000 and 2000 Hz. Sound absorption coefficient ®data is given for all TRAC ceilings. This enables calculation of noise

reduction or reverberation time.

The increasing use of hard finishes and stone/tile finishes in offices requires ®the use of highly sound absorbent ceilings. TRAC ceilings offer NRC values

of 0.75 upto 1.05 for different ceiling types.

Traditionally, whenever sound absorption is required, perforated metal

ceiling panels are backed with a sound absorbing layer of mineral wool or

fiberglass. The use of a fibrous sound absorbing medium always has other

drawbacks. These include the difficulty in working with the fibrous materials

because of skin irritation and the problem of fibers letting loose into the air

stream in an air-conditioned environment.

® ® TRAC Acousti-Panel ceilings overcome these problems. This ceiling range

comprises perforated panels with an acoustic nonwoven factory applied to

the rear of the panels. Due to the controlled sound impedance of this ®perforated panel, and with a backing air space (ceiling plenum), the TRAC

®Acousti-Panel provides excellent sound absorption properties without the

use of any fibrous material behind the perforated panel. Please refer to

product data sheets for availability information.

SOUND TRANSMISSION LOSS

Sound transmission loss is a measurement of sound insulation between one

room and another. Some manufacturers provide sound transmission loss

(attenuation) values for ceiling tiles. This information is of doubtful utility

because ceiling tiles are supported on grids and have penetrations through

them to accommodate light fittings and air conditioning diffusers. The overall

sound transmission loss of such a composite ceiling will be 10-20 dB lower

than the transmission loss of the ceiling panel or tile alone.

When designing for sound insulation between rooms, the partition

separating the rooms is of major concern. To prevent flanking sound

transmission through the suspended ceiling, it is important that partitions do

not stop at the ceiling, but are extended right up to the roof slab above. The

suspended ceiling should not be relied upon to give sound insulation

between adjacent spaces.

FIRE RESISTANCE

All ceilings provide Class 1 Surface Spread of Flame in accordance with BS 476-part 7 (1987). The materials are incombustible as per BS 476-part 4

(1970) and satisfy Class O as per BS 476-part 6 (1989).

® TRAC

Sound Absorption Data Perforated Metal Tile

Perforated Tile with Non-Woven Acoustic

®TRAC - THE ENVIRONMENT FRIENDLY CEILING

All ceilings are manufactured from fully recyclable materials.

ceilings are pre-painted and fully pre-fabricated in the factory. The ceiling

systems are friendly to handle, and will not promote growth of bacteria or

fungi.

®TRAC ceilings exhibit excellent corrosion resistance. They can withstand

very high humidity (upto 100%) and are suitable for use in outdoor areas.

® ®TRAC TRAC

When selecting a suspended ceiling, the designer needs to weigh the costs ®and performance requirements. There is a TRAC ceiling for every need.

Ceilings systems are available in gypsum, coated steel and coated ® aluminium. TRAC ceilings are available in a variety of designs including lineal

ceilings, clip-in or lay-in tile and plank ceilings, and C-grid (band raster)

ceilings. Metal ceilings are manufactured in aluminium and steel with coil

coated or powder coated finishes. All metal ceilings are available in a

perforated version for sound absorption, and are designed to integrate with

standard lighting fixtures, air diffusers, and partitions.

Please refer to detailed product data sheets for specific applications.

GRG (Glass Reinforced Gypsum) Ceiling System

84R Lineal CeilingC-Grid (band raster) Ceiling

®TRAC The Right Ceiling for you

Frequency, Hz 125 250 500 1k 2k 4k NRC

84C Wool/200mm air space

perf/25mm Mineral 0.38 0.90 1.08 1.02 1.10 0.79 1.03

84R Wool/200mm air space

perf/25mm Mineral 0.22 0.69 0.96 0.91 0.96 0.86 0.88

150C Wool/200mm air space

perf/25mm Mineral0.30 0.74 0.88 0.58 0.71 0.70 0.73

Perf Wool/200mm air space

tile/25mm Mineral0.50 1.00 1.02 1.07 1.06 1.05 1.04

Perf Wool/200mm air space

tile/acoustic

0.48 0.93 0.62 0.69 0.80 0.75 0.76

Mineral Fiber Tile 0.13 0.29 0.47 0.58 0.57 0.54 0.48

0.09 0.10 0.10 0.12 0.25 0.35 0.14GRG T 206, no holes

GRG T 206, no holes/25MW 0.20 0.40 0.55 0.10 0.21 0.50 0.32

38 mm

24 mm

38 mm

3 4NNOVATE NITIATE NTEGRATE

Page 5: Broucher Ceiling

84 16

FLUSH PROFILE(OPTIONAL)

16

473

1

32

THE RIGHT CEILING FOR THE RIGHT APPLICATION

INTERARCH is a pioneer of coated metal architectural products in India and

has a consistent record of product innovation. Over the years, millions of

square metres of INTERARCH architectural building products have been

installed in India and abroad.

®TRAC ceilings are available in a wide range of panel types for decorative ®and functional applications. TRAC ceilings are suitable for use in interior and

exterior areas in offices, hospitals, schools, restaurants, shops, hotels, ®airports and other buildings. TRAC ceilings are also suitable for industrial

use and are specially suited to aggressive environments inside factory

buildings.

DESIGN AND ENGINEERING SUPPORT

The Interarch Architectural Projects and Service Group (ASG) provides

customers with complete design, engineering, and drafting support.

ASG can help you convert your most imaginative designs into reality. Shop

drawings and detailed bill of quantities are prepared for all projects to ensure

correct product supply and application.

84R Interior & Exterior Ceilings

84R INTERIOR

Material

Panels: 84mm wide x 16mm deep, made out of 0.50mm aluminium alloy

AA3005/ 5052 with stove enamelled coil coated finish / 0.45

galvanised steel with stove enamelled coil coated finish.

® (Colour according to TRAC colour chart and availability chart)

Panel length upto approx 5m

When perforated, hole diameters are 2mm on 5mm centres (standard) or

1mm on 2.5mm centres (microperforated), the holes representing15% of

the perforated area.

Panel Carriers: 32mm wide, 39mm deep, made out of 0.95mm

aluminium alloy AA 5052/0.6mm galvanised steel, with prongs to hold the

panels in a module of 90mm/100mm (gap 6/16mm, open). Optional gap

closures with recessed or flush join profiles for 16mm gap.

3105/

Flush join Profiles : Made of enamelled aluminium, for 100mmmodule

(16mm gap).

Suspension: By means of suspension rods and spring clips. One suspension

for every 1.5 to 2 sq.m.

Panel Span: 1.3m max. with insulation, 1.5m max. without insulation.

Carrier Span: 1.3m max. spacing of suspension rods.

Finish

Coil Coated: Panels will be finished on exposed side with 20 microns

polyester coil coating over primer and on rear side with a wash coat.

84R EXTERIOR

Material

Panels: 84mm wide x 16mm deep, made out of 0.60mm aluminium alloy

AA 3005 / 3105 / 5052 with stove enamelled coil coated finish.

®(Colour according to TRAC colour chart and availability chart)

Panel length upto approx 5m

Stringers: 34.5mm wide, 48mm deep, made out of 0.95mm aluminium

alloy 5052, with prongs to hold the panels in a module of 90mm / 100mm

(gap 6 / 16mm open). Optional gap closure with flush join profile for

16mm gap.

Suspension: By means of rigid suspension rods or on steel substructure.

Panel Span: 800mm max.

Stringer Span : 500mm max. spacing of suspension angles.

Finish

Coil Coated: Panels will be finished on exposed side with coil coated stove

enamelled PVF2 or polyurethane paint with a wash coat on the rear side.

32

39

16

84

5 5 À2

À12.5

2 5

®TRAC Ceilings

Sound Absorption Data

Frequency, Hz 125 250 500 1000 2000 4000 NRC

84R perf/25mm MineralWool/200mm air space 0.22 0.69 0.96 0.91 0.96 0.86 0.88

1.20

1.00

0.80

0.60

0.40

0.20

0.00

Absorption Coefficients

Frequency, HzFrequency, Hz

...84R perf/25mm MineralWool/200mm air space

125 250 500 1000 2000 4000 NRC

0.20 0.69 0.96 0.91 0.96 0.86 0.88

Abso

rpti

on C

oeff

icie

nt

5 6NNOVATE NITIATE NTEGRATE

Page 6: Broucher Ceiling

84 16

45

12.5

32

39

12.5

12.5

32

84

184

5 5À2

À12.5

2 5

EXTERIOR

Material

Panels: 150mm wide x 17mm deep, made out of 0.60mm aluminium alloy

AA 3105 / 5050 with stove enamelled coil coated finish / 0.50mm galvanised

steel with stove enamelled coil coated finish.

(Colour according to Trac colour chart and availability chart)

Panel length up to approx 5m

Stringers: 34.5mm wide, 48mm deep made out of 0.95mm aluminium

alloy AA 5052/0.60mm galvanised steel, with prongs to hold the panels in

module of 150mm.

Suspension: By means of rigid suspension or mounted on a steel

sub-structure.

Panel Span: 1000mm max.

Stringer Span: 500mm max. spacing of suspension angles.

Finish

Coil Coated: Panels will be finished on exposed side with coil coated stove

enamelled PVF2/ polyurethane/SMP paint with a wash coat on rear side.

angles Sound Absorption Data

Frequency, Hz 125 250 500 1k 2k 4k NRC

150C Wool/200mm air space

perf/25mm Mineral 0.30 0.74 0.88 0.58 0.71 0.70

Sound Absorption Data

Frequency, Hz 125 250 500 1k 2k 4k NRC

84C Wool/200mm air space

perf/25mm Mineral0.38 0.90 1.08 10.2 1.10 0.79 1.03

1.20

1.00

0.80

0.60

0.40

0.20

0.00

Absorption Coefficients

125 250 500 1000 2000 4000 NRC

0.38 0.90 1.08 1.02 1.10 0.79 1.03

Frequency, Hz

84C perf/25mm Mineral Wool/200mmair space

Abso

rpti

on C

oeff

icie

nt,

1.00

0.80

0.60

0.40

0.20

0.00

Absorp

tion C

oeff

icie

nt,

150 C perf./25mm Mineral Wool /200 mm air space

Absorption Coefficients

125 250 500 1000 2000 4000 NRC

0.30 0.74 0.88 0.58 0.71 0.70 0.73

Frequency,Hz

SUSPENSION ANGLEAT 500mm C/C

SUSPENSION CLIP

PANEL CARRIER

150-C PANEL

EDGE COVER PROFILE

39

32

15

150/75

84C Ceiling System

0.73

84C/184C INTERIOR

Material

Panels:

23.5mm, made out of 0.50mm aluminium alloy AA 3005/3105/5052 with

stove enamelled coil coated finish 0.45mm galvanised steel with stove

enamelled coil coated finish.

®(Colour according to TRAC colour chart and availability chart)

Panel lengths up to approx. 5m

Panel carriers: 32mm wide, 39mm deep, made out of 0.95mm aluminium

alloy AA 5052/0.6mm galvanised steel, with cutouts to hold the panels in a

module of 100mm (84C) or 200mm (184C), gap 16mm closed.

Suspension: By means of suspension rods and spring clips. One

suspension for every 1.5 to 2 sq.m.

Panel Span: 1.3m max. with insulation, 1.6m max. without insulation.

Carrier Span: 1.3m max. spacing of suspension rods.

Finish

Coil Coated: Panels will be finished on exposed side with 20 microns

polyester coil coating over primer and on the rear side with a wash coat.

84mm/184mm wide x 12.5mm deep, with a recessed flange of

84C EXTERIOR

Material

84C ceilings can also be used for exterior applications when suspended by

rigid suspension rods or mounted on a steel substructure. 84C exterior

ceiling is available in 0.50mm aluminium alloy AA 3005/ 5052 with

stove enamelled coil coated finish.

(Colour according to colour chart and availability chart)

Panel Span: 800mm max.

Carrier Span: 500mm max. spacing of suspension angles.

Finish

Coil Coated: Panels will be finished on exposed side with coil coated stove

enamelled PVF2 or polyurethane paint with a wash coat on the rear side.

3105/

®TRAC

84C/184C Interior & Exterior Ceilings 150F/200F Interior & Exterior Ceilings/75C & 150C Interior

150F INTERIOR / EXTERIOR

INTERIOR

Material

Panels: 150mm wide x 17mm deep, made out of 0.60mm aluminium alloy

AA 3105 with stove enamelled coil coated finish / 0.50mm

galvanised steel with stove enamelled coil coated finish.

®(Colour according to TRAC colour chart and availability chart)

Panel length upto approx 5m

Stringers: 34.5mm wide, 48mm deep made out of 0.95mm aluminium

alloy AA5052/0.60mm galvanised steel, with prongs to hold the panels in a

module of 75 /150mm.

Suspension: By means of suspension rods and spring clips.

Panel Span: 1.5m max. with insulation, 1.8m max. without insulation.

Stringer Span: 1.5m max. spacing of suspension rods.

Finish

Coil Coated: Panels will be finished on exposed side with 20 microns

polyester coil coating over primer and on the rear side with a wash coat.

/3105/5052

75C/150C INTERIOR

® TRAC

because of its smooth, closed appearance. The panels about each other

with a narrow V-groove. They are installed to carrier profiles and can be

simply demounted individually, by inserting a plain strip between the

profiles.

®As with all TRAC ceilings, the 75C/150C can be applied in all types of

buildings and because of their closed appearance they are particularly

suitable for domestic applications: living rooms, kitchens, corridors etc.

Panels: 75mm/150mm wide x 15mm deep with bevelled groove between

panels, made out of 0.50mm thick aluminium alloy AA 3005/3105/5052 or

0.5mm thick galvanised steel.

®(Colour according to TRAC colour chart and availability)

Panel lengths upto approx 5 m.

When perforated, hole diameters are 2mm on 5mm centres (standard) or

1mm on 2.5mm centres (micro-perforated), the holes representing 15% of

the perforated area (150C only).

Panel Carriers: 32mm wide, 39mm deep made out of 0.95mm aluminium

of 0.6mm galvanised steel, with prongs to hold panel in a module of 15mm.

Suspension: By means of G.I. rod hangers and suspension clips.

Panel Span: 1.3m max. with insulation, 1.5m max. without insulation.

Carrier Span: 1.3m max. spacing of suspension rods.

Finish

Coil Coated: Panels will be finished on exposed side with 20 microns

polyster coil coating over primer and on the rear with a wash coat.

ceiling type 75/150C distinguishes itself from the other types

150/200

17

48

7 8NNOVATE NITIATE NTEGRATE

Page 7: Broucher Ceiling

®TRAC tile and plank design ceiling system has been developed to meet

both practical and aesthetical requirements of modern ceilings. The major ®advantages of the TRAC tile/plank system are innovative suspension

systems, optional rigid grid system for suspension of exterior ceilings, choice

of tile material, extensive range of colours and finishes and a choice of

perforations and flexibility in design specially with the plank ceiling system.

The tile/plank ceiling systems are offered in stove enamelled coil coated

steel and aluminium and powder coated steel and aluminium finishes and

offer the advantage of easy cleaning, non-static properties and inert material.

Incandescent and halogen type spot lights can be easily incorporated in the

tile ceilings and fluorescent fittings within the plank ceilings.

Tiles

Tiles are manufactured out of coil coated galvanised steel/aluminium alloy

AA 3105 on advanced equipment, which includes several

levelling stages in the manufacturing process. For the clip-in tile, two sides of

each tile are raised and pipped and stopped to ensure positive engagement

into the spring tee yet allow demounting of individual tiles.

For the lay-in system, the tiles have a flange on each end which lays on the

exposed grid. All tiles have square/bevelled edges.

Planks

Planks are manufactured out of coil coated aluminium alloy

AA 3105/3005/5202 galvanised steel produced on advanced equipment

which includes several levelling stages.

Clip-in planks: The short sides of each plank are raised and pipped and

stopped to ensure positive engagement into the spring tee, yet allow

demounting of the individual planks

Lay-in and C-Grid planks: These planks have a flange on each end, which

lay on the exposed grid or C-grid. The planks can be laid and easily removed

without the aid of special tools. Planks over 1500mm in length have an

additional stiffening flange on the long side.

Suspension

Clip-in-system: Tiles/planks are suspended by means of a suspension

system comprising 0.5mm galvanised steel clip-in profiles installed at correct

spacing to support the tiles/planks. Suspension profiles are suspended from

roof structure by GI ceiling brackets. GI suspension angles and hold-on

clamps at max. 1200mm centre to centre along the clip in profile. This rigid

suspension is also suitable for exterior use.

Lay-in-System: Suspension system is standard 24mm table exposed metal

grid. Grid features 38mm high main runners and cross tees, roll formed

from galvanised steel to BS 2989 Z-18 zinc coating. The main runners

feature bayonet ends and the cross tees stab ends for quick and simple

coupling. The runners are pre-slotted to construct a variety of layouts. The

main and cross runners are provided with a coil coated steel capping on the

exposed table in off-white colour. The grid is suspended from the roof with

GI wire rod and quick adjustment suspension hangers along the runners.

The grid system is designed to satisfy ASTM C635 intermediate duty loading

and deflection criteria. This system is only suitable for interior use.

C-grid System: The suspension system consists of exposed C shaped

runners which are installed parallel to each other to form continuous main

/3005/5202

courses. Spacing between runners corresponds to the exposed length of

the plank. When a square grid is required, this is made by incorporating

shorter C-shaped cross members that are butt-jointed against the main

runner and tied with a special cross piece bracket. This system is only

suitable for interior use. The C runners are suspended from the roof slab

with special suspension shoes and GI suspension angles at a maximum

distance of 1200mm centre to centre.

Edge Cover Profile

Tiles/planks are trimmed along the wall perimeter by means of 19x19mm

roll formed steel or aluminium edge cover profile.

Paint Finish

Steel tiles/planks: Steel tiles/planks are finished on exposed side with 20

micron polyester coil coating over primer in approved shade and backing

coat on rear surface (nominal 5 microns), or with a 50 micron epoxy

polyester powder coating on exposed surface.

Aluminium tiles/planks: Aluminium tiles/planks are finished on exposed

side with 20 micron polyester coil coating over primer in approved shade

and backing coat on rear surface (nominal 5 microns), or with a 50 micron

epoxy polyester powder coating on exposed surface. Wall angles are

finished with 50 micron epoxy polyester powder coating paint in broken

white shade.

Perforations

®TRAC tiles and planks are also available with perforations for providing ® acoustic performance characteristics. TRAC tiles and planks are perforated

as a standard with 2.5mm dia. holes at 5.5mm centre to centre in a regular

pattern. Other special/non-standard perforations are also available. Tiles

and planks when backed with 25mm thick resin bonded mineral wool2(48 kg/m ) provide good sound absorption. Tiles and planks are also

available with a factory applied acoustic tissue to the back side, which

provides good sound absorption.

Sound Absorption Data

Frequency, Hz 125 250 500 1k 2k 4k NRC

Perf Tile/Acoustic tissue 0.93 0.62 0.69 0.80 0.75 0.76

Perf Tile/25mm Mineral Wool 1.041.051.061.071.021.000.50

0.48

1.20

1.00

0.80

0.60

0.40

0.20

0.00

Absorption Coefficients

Abso

rpti

on C

oeff

icie

nt,

Frequency, Hz

Perf tile/acoustic tissue

Perf tile/25mm Mineral Wool

125 250 500 1000 2000 4000 NRC

0.48 0.93 0.62 0.69 0.80 0.75 0.76

0.50 1.00 1.02 1.07 1.06 1.05 1.04

Tile & Plank Design CeilingsTiles and plank ceilings are available with clip-in, lay-in and C grid

suspension systems.

Clip-In System

The clip-in system consists of 0.5mm galvanised steel clip in profile which is

used as the primary suspension and if required, as a secondary suspension.

This system features:• a rigid grid system to ensure a level ceiling and

• a hidden suspension system for an uncluttered, monolithic ceiling appearance

Lay-In System

The lay-in system comprises the Trac 8011 exposed grid suspension. This

grid features stab-in coupling and is demountable.

This system features :

• easy access to the plenum

• a rigid fire rated grid to ensure a level ceiling and an exposed grid

suspension which accentuates the grid pattern

C-Grid Suspension System

The C-grid suspension system consists of exposed C-shaped runners which

are installed parallel to each other or in a square grid to form continuous

main courses. The planks are hooked onto these grids.

This system features:

• the advantage of the possibility to fix partition walls to the strong C-Grid

• an exposed wide suspension system which accentuates the grid pattern

and allows easy access to the plenum

Alternative Lay-Out

(TEGULAR)

WALL

HOOK AND BUTTERFLY CLIP

CROSS TEE

TRAC LAY- IN TILEEDGE COVER PROFILE TRAC L(SQUARE EDGE)

AY- IN TILE / PLANK

Lay-In System

0.7

METAL FASTENER

R.C.C. SLAB

CEILING BRACKET

SUSPENSION ANGLE

SUSPENSION SHOE

TRAC PLANKS

C-GRID C-GRID

WALL

C Grid Suspensions System

CEILING BRACKETAT 1200mm C/C

CUT EDGE OF PLANK(FOLDED UP) RESTINGON EDGE PROFILE

G.I. SUSPENSION ANGLEAT 1200 mm C/C

HOLD ON CLAMP’AT 1200MM C/C (Max.)

CLIP IN PROFILE

EDGE PROFILE

WALL

TRAC TILES/PLANKS

Clip-In System

D

X

e

f

g

d

Lay-In Plank

Straight Joints

Combined Tile Sizes

C-Grid Ceiling with Light Fittings

TRAC PLANKS

C-GRID

WALL

Code Size (mm) Material ThicknessWidth Length Aluminium Steel

TILES 600 600 0.7 0.5600 300 0.7 0.5

PLANKS 254 1264 0.7 0.6305 1264 0.7 0.6284 1247 0.7 0.6

Tiles and Plank Ceilings (Standard Available Sizes)

9 10NNOVATE NITIATE NTEGRATE

Page 8: Broucher Ceiling

GRG TILES

TILES

Composition

The GRG range of ceiling tiles are manufactured from glass

reinforced gypsum and comprise non-combustible gypsum casting

plaster reinforced with a glass fibre membrane resulting in a light weight,

strong and prestressed panel.

Surface Finish

The plaster has a silky smooth or textured moulded finish.

Colour

The tiles are normally supplied in their natural white finish and can be

pre-decorated to order.

Dimensions

All designer tiles are designed for installation on a standard 600x600mm

module 24mm table exposed metal grid and are precision made to within

plus or minus 0.25mm

Weight

For a guide, the tile weights are shown below but may vary depending

upon the gypsum source.

®TRAC

TRAC GRG Ceiling®

Fire Performance

Non-combustibility: GRG tiles are rated non-combustible as

defined in BS 476: Part-4, 1970.

Surface Spread of Flame: GRG tiles are rated Class 1 for surface

spread of flame to BS 476: Part-7, 1987.

Fire Propagation: Test results to BS 476: Par-6, 1989 indicate a Class O

surface.

Smoke and Toxic Fume Emission: The tiles are zero rated for smoke

emission. No toxic fumes are given off.

Humidity Resistance

®TRAC

®TRAC

The tiles have excellent moisture resistance and can be used in areas of high

humidity including covered external areas, kitchens and bathrooms. Tested

in an atmosphere of 95% R.H. at 12°C for 14 days, the tiles did not sag or

Tile

T206 Fine Texture Tiles

T506 Travertine

T826 Shallow Coffers

T906 Open Cell Tiles

T906C Closed Cell Tiles T906C

T906

T826 T206

distort and showed only a minimal increase in weight. Unlike most other

ceiling materials, this important attribute can often be used to speed up the

building program by installing the ceiling before the building is fully

weathertight.

T506

3.9

3.9

4.5

4.15.6

10.8

10.8

12.5

11.414.5

0.60

0.50

0.40

0.30

0.20

0.10

0.00

Absorption Coefficients

Abso

rpti

on C

oeff

icie

nt, a

Frequency, Hz

GRG T 206, no holes/25 MW

GRG T 206, no holes

125 250 500 1000 2000 4000 NRC

0.20 0.40 0.55 0.10 0.21 0.50 0.32

0.09 0.10 0.10 0.12 0.25 0.35 0.14

Biological

GRG tiles will not support the growth of bacteria or other micro-

organisms.

Lifespan

Under normal conditions GRG tiles will not deteriorate and can be

expected to last the lifetime of the building.

Suspension

Suspension system is standard 24mm table exposed metal grid.

exposed metal grid systems are designed for maximum strength. The grid

features main runners and cross tees roll formed from galvanised steel. The

main and cross runners are provided with stab-in coupling for quick

installation. The runners are pre coated to construct a variety of lay outs.

Main and cross runners are provided with a coil coated steel capping on the

exposed table in off-white colour. Grid system features main and cross tees

38mm high. The grid is suspended from the roof with GI wire rods and or

quick adjustment suspension hangers at maximum 1200mm along the main

runners. GRG tiles are designed for lay-in mounting from below into

standard grid.

Transport, Handling and Storage

GRG tiles are supplied and packed in cardboard cartons. Cartons

should be transported and stacked in the vertical position only, never flat; the

stack should be a maximum of three cartons high. Similarly, tiles should be

stacked vertically when awaiting fixing.

Installation

Main tees should normally be fixed at 1200mm centres with hangers every

® TRAC

®TRAC

®TRAC

®TRAC

®TRAC

TRAC® GRG CEILINGS

Sound Absorption Data

Frequency, Hz 125 250 500 1k 2k 4k NRC

GRG T 206, no holes/25 MW 0.20 0.40 0.55 0.10 0.21 0.50 0.32

GRG T 206, no holes 0.09 0.10 0.10 0.12 0.25 0.35 0.14

1200mm along the length of the tee. The tees would be in filled with

1200mm and 600mm cross tees. The grid manufacturers

recommendations should be followed at all times.

Note: All perimeter tiles may be supported on only 3 sides without risk of

sagging. Tiles can easily be cut by using a carpenters fine tooth saw; the

lines should be placed face down on a flat, clean surface for cutting.

Kg/tile 2Kg/m

Texture Tiles

11 12NNOVATE NITIATE NTEGRATE

Page 9: Broucher Ceiling

Accessories

LAY-IN SUSPENSION

HOOK AND BUTTERFLY CLIP110050

MAIN RUNNER850300

CROSS TEE (600MM)812300

CROSS TEE (1200MM)814300

WALL ANGLE144000

CEILING 150C

PANEL CARRIERST-432689.1863 (Black)AL-332689.1863 (Black)

CEILING 84C/184C/84R

PANEL CARRIERST-432686.1863AL-332686.1863

STRINGER V5 (84-R)AL-332185.1863

PANEL CARRIER(84-R 90mm MODULE)ST-432687.1863AL-332687.1863

CARRIER SPLICEAL-334173.1863

PANEL SPLICE (84-C)AL-334517.1863

CEILING 200F/CLIP IN TILE & PLANK

HOLD ON CLAMPST-440101.0000

HOLD ON CLAMP WITHADJUSTMENT CLIPST-440106.0000

CEILING BRACKETST-401144.0000

CLIP IN PROFILEST-440103.0000

SUSPENSION ANGLEST-401146.0000

CEILING 150F

PANEL SPLICEAL-334175.1863 (Black)AL-334175.0280 (Natural)

STRINGER V9ST-401850.1863AL-332186.1863

C-GRID SUSPENSION (AS PER C-GRID WIDTH)

SUSPENSION SHOEST-4021XX.0000

WALL CONNECTORST-4041XX.0000

C-GRIDST-4011XX.0000

CROSS CONNECTORST-4031XX.0000

CEILING 84R

FLUSH JOIN PROFILEAL-332104.0000

ROD HANGER1000MM ST-434878.0000500MM ST-434862.0000

SUSPENSION CLIPST-434795.0000

EDGE COVER PROFILE(W-SHAPED)ST-442414.1863

EDGE COVER PROFILE(L-SHAPED)ST-432408.0000AL-332406.0000

®List of major projects where TRAC ceiling system has been used

S.NO. NAME OF PROJECT LOCATION

1 National Thermal Power Corporation Faridabad

2 Power Grid Substation Satna / Raipur

3 Ansal Plaza Delhi

4 Indian Farmers Fertiliser Cooperative Limited Phulpur

5 GAIL (India) Limited Rajasthan / Gandhar

6 Rourkela Steel Plant Rourkela

7 Krishi Anusandhan Bhawan Pune

8 Mahindra & Mahindra Limited Mumbai

9 KFC Restaurant New Delhi

10 All India Institute of Medical Sciences New Delhi

11 CPWD New Delhi

12 Ericsson New Delhi

13 Defence Research and Development Organisation Srinagar

14 National Hydroelectric Power Corporation Ltd. Faridabad

15 Crompton Greaves West Bengal

16 Delhi Metro Rail Corporation Shastri Park

17 Punjab Institute of Medical Science Jalandhar

18 Control Room PGCIL All-India

Indian Oil Corporation Ltd. All-India

Bharat Petroleum Corporation Limited All-India

Reliance Petroleum Limited All-India

Mumbai Airport (International Terminal) Mumbai

Bangalore Airport (Public Lounge Area) Bangalore

Hyderabad Airport (Public Lounge Area) Hyderabad

Guwahati Airport Guwahati

Bhopal Airport Bhopal

Raipur Airport (Public Lounge Area) Raipur

Agartala Airport Agartala

Tezpur Airport Tezpur

R.R. Hospital New Delhi

Escorts Heart Institute New Delhi

Leelawati Hospital Mumbai

Indian Spinal Injuries Centre New Delhi

Apollo Hospital New Delhi

IGMH Hospital Maldives

PGI Hospital Chandigarh

19 PETROL PUMP CANOPIES

20 AIRPORTS

21 HOSPITALS

13 14NNOVATE NITIATE NTEGRATE

Page 10: Broucher Ceiling

Regional Offices and Manufacturing Units

Interarch Building Products offer turnkey operations with regional offices and project control

centres for marketing, sales and coordination at all locations across India.

M/s. Interarch Building Products Pvt. Ltd.

Plot No: D-1/1, SIPCOT Industrial Park, Mambakkam,

Sriperembudur - 602 105

Kancheepuram (Tamil Nadu)

Tel: 044 - 27190710

M/s. Interarch Building Products Pvt. Ltd.

Plot No: A, Khasra No: 276-A,

2 KM on Kichha - Rudrapur Road,

Kichha - 263 148

Distt: Udham Singh Nagar (Uttarakhand)

Mob: 09760690304

For faster processing of enquiries from - , Chandigarh,Hyderabad, Indore, Kolkata, Kochi, Mumbai, Nagpur, Pune, please contact:

Ahmedabad, Bangalore, Baroda, Bhopal, Chennai

M/s. Interarch Building Products

Plot No: 29, Udyog Vihar,

Greater Noida - 201 306

Tel: 0120 - 4502300, Fax: 0120 - 2560793

M/s. Interarch Building Products Pvt. Ltd.

Plot No: 14, Sector - 2,

Integrated Industrial Estate, Pantnagar

Rudrapur - 263 153 (Uttarakhand)

Mob: 09319268211

Pvt. Ltd.

Central Marketing Office

B-30, Sector-57, Noida - 201 301

Tel: 0120 - 4170200 / 2581029 / 2586300

Fax: 0120 - 2581017 / 4170200

E-mail: [email protected]

Website: www.interarchbuildings.com

Mumbai

Kolkata

ChennaiBangalore

Hyderabad

Pune

Ahmedabad

NOIDAGreater NOIDA

Pantnagar

Central Marketing Office

Regional Office

Manufacturing Unit

NNOVATE NITIATE NTEGRATE

Support Network, India

Bhopal

Indore

Chandigarh

NNOVATE NITIATE NTEGRATE

15 16


Top Related