+ All Categories
Transcript

Project Type

DESCRIPTION

Brite Energy Solutions - Tom Knoblock - 1-844-533-2897 Toll Free - www.Brite-LED-Solutions.com

| | | | |

DATASHEET 11.20.2014Specifications and dimensions subject to change without notice

PUC UNV1- (120-277 VAC) 4100 (Non-Dimmable)

PUC UNV1 - (120-277 VAC) 4100DM (Dimmable)**

PUC UNV2 - (347/480 VAC) 4100DM (Dimmable)***

Canopy LED LuminaireStandard Flux

112 W / 12,600 Lumens

ENERGY DATA

347-480

110

12600

114.5

5000

80 min

>200,000

150,000

-40 to 45

The Canopy Star canopy LED luminaire from US LED is a perfect solution for parking structures, shopping area walkways, petrol stations and exterior canopies. The Canopy Star LED canopy is surface mounted for easy adaptation with a typical mounting height of 10 to 25 feet. Designed to illuminate area features with sharp, accurate color to increase security and visibility, the Canopy Star is cost effective to install and will replace conventional fluorescent, HPS and metal halide lighting.

POWER SUPPLY INFORMATION

FEATURES

Class 2 compliant design (low voltage, limited power)

L70 lifetime of >200,000 hours*

Luminaire is IP66 compliant

Protective coating added to resist corrosion

5-year warranty

l

l

l

l

l

SPECIFICATIONS

Dimensions (in)

Units/carton

Net weight

Environmental Rating

18.62 x 18.62 x 2.75

1

9 lbs

Wet

CERTIFICATIONl

l

l

Input Voltage (VAC)

System Level Power (W)

Delivered Lumens (Lm)

System Efficacy (Lm/W)

Color Temperature (K)

Color Rendering Index

L70 Calculated Life (Hrs)*

L85 Calculated Life (Hrs)*

Operating Temp (ºC)

120 - 277

112

12600

112.5

5000

80 min

>200,000

150,000

-40 to 45

Series Drive CurrentType

Example: PUC-UNV1-4100

UL 1598 certified by Intertek (ETL 4006735)

DesignLights Consortium qualified

LM-79 available

FIXTURE ORDERING INFORMATIONExample: CNP3-50-2

CNP3 50 2

Series

CNP3

Color Temp (K)

50 5000K

* US LED product ‘Lifetimes’ refer only to the LED light engine, not the power source, and are based on the Illuminating Engineering Society’s TM21 methodology based on 25°C/77°F ambient temperature. The lifetimes are solely meant to be a guide for expected LED degradation and not a warranty or predictive of their actual life, which can be affected by ambient temperatures and other factors.

Fixture Color

2 White

** PUC-UNV1-4100DM is not DesignLights Consortium qualified. Special order only.*** Special order only.

Project

Catalog #

Type

DESCRIPTION

US LED | 6807 PORTWEST DR | HOUSTON, TX 77024 | T 866 972 9191 | F 713 972 9393 | [email protected] | www.usled.com

PRELIMINARY DATA SUBJECT TO CHANGEDATASHEET 11.20.2014Specifications and dimensions subject to change without notice

PUC UNV1- (120-277 VAC) 8200 (Non-Dimmable)

PUC UNV1 - (120-277 VAC) 8200DM (Dimmable)**

PUC UNV2 - (347/480 VAC) 8200DM (Dimmable)**

Canopy LED LuminaireHigh Flux

190 W / 19,700 Lumens

ENERGY DATA

347-480

189

19,800

105

5000

70 min

>200,000

150,000

-40 to 45

The Canopy Star canopy LED luminaire from US LED is a perfect solution for parking structures, shopping area walkways, petrol stations and exterior canopies. The Canopy Star LED canopy is surface mounted for easy adaptation with a typical mounting height of 10 to 25 feet. Designed to illuminate area features with sharp, accurate color to increase security and visibility, the Canopy Star is cost effective to install and will replace conventional fluorescent, HPS and metal halide lighting.

POWER SUPPLY INFORMATION

FEATURES

Class 2 compliant design (low voltage, limited power)

L70 lifetime of >200,000 hours*

Luminaire is IP66 compliant

Protective coating added to resist corrosion

5-year warranty

l

l

l

l

l

SPECIFICATIONS

Dimensions (in)

Units/carton

Net weight

Environmental Rating

18.62 x 18.62 x 2.75

1

9 lbs

Wet

CERTIFICATION

Input Voltage (VAC)

System Level Power (W)

Delivered Lumens (Lm)

System Efficacy (Lm/W)

Color Temperature (K)

Color Rendering Index

L70 Calculated Life (Hrs)*

L85 Calculated Life (Hrs)*

Operating Temp (ºC)

120 - 277

190

19,700

104

5000

70 min

>200,000

150,000

-40 to 45

Series Drive CurrentType

Example: PUC-UNV1-8200

FIXTURE ORDERING INFORMATIONExample: CNP4-50-2

CNP4 50

Series

CNP4

Color Temp (K)

50 5000K

* US LED product ‘Lifetimes’ refer only to the LED light engine, not the power source, and are based on the Illuminating Engineering Society’s TM21 methodology based on 25°C/77°F ambient temperature. The lifetimes are solely meant to be a guide for expected LED degradation and not a warranty or predictive of their actual life, which can be affected by ambient temperatures and other factors.

Fixture Color

1 Bronze**

2 White

** Special order only.

l

l

l

UL 1598 certified by Intertek (ETL 4006735)

DesignLights Consortium qualified

LM-79 available

INSTALLATION GUIDECNPx-50

Page 1

Updated 09.26.13

#44-000017

The installation must only be performed by a licensed electrician.

To prevent death, injury or damage to property, this product must be installed in accordance to National Electrical Code (NFPA70) in the US or Canadian Electrical Code (CSA22.1) in Canada.

Disconnect power before installing the product or servicing it.

Wait until fixture has cooled down before installing or servicing the fixture.

MIN. 90°C SUPPLY CONDUCTORS

WARNINGl

l

l

l

l

MODEL NUMBERSThis installation instructions covers the following products:

Power Supplies1. 50W Power Unit: PUC-UNV1-2100 or PUC-UNV2-21002. 75W Power Unit: PUC-UNV1-3000 or PUC-UNV2-30003. 96W Power Unit: PUC-UNV1-3570 or PUC-UNV2-35704. 192W Power Unit: PUC-UNV1-7140 or PUC-UNV2-7140

Luminaires1. CNP1-50 Series Luminaires2. CNP2-50 Series Luminaires

BOX CONTENTS

Mounting Plate Assembly

Wire Harness/Cover Assembly

CanopyStar Fixture

LED Driver withMounting Bracket

Tools Needed1. 4” Hole Saw2. #2 Phillips Screw Driver3. ¼” Hex Driver

Page 2

Updated 09.26.13

CNPx-50INSTALLATION GUIDE

#44-000017

1. Using4”holesaw,cutholeincanopywherefixtureistobemounted.Holelocationneedstobecenteredbe-tweencanopyribstoallowwireharness/coverassemblytofit.

2. Install mounting plate assembly by folding mounting tabs in, insert mounting plate into 4” hole and secure by tightening mounting tab screws using #2 Phillips screw driver. See Figures 1 and 2.

INSTALLATION INSTRUCTIONS

4” hole

Mounting tabs

FIG 1 FIG 2

Mounting tabscrews

FIG 3 FIG 4

3. Hang Canopy Fixture on mounting plate assembly by hooking hinge on mounting plate hook. Secure by sliding locking plate forward into slot and tightening #6-32 locknut. See Figures 3 and 4.

Locking plate

Locknut

INSTALLATION GUIDECNPx-50

Page 3

US LED

Updated 09.26.13

#44-000017

4. Route wires through center of mounting plate assembly. See Figure 5.

5. Take wire harness assembly and make power connections using approved electrical connector. See wire diagrams.

INSTALLATION INSTRUCTIONS

FIG 5 FIG 6

FIG 7 FIG 8

6. Pack excess wire in center of mounting plate assembly and mount cover using #10 sealing weather resistant screws supplied. See Figure 7.

7. Completeinstallationbyswingingfixtureintoplaceandsecuringwithmountingscrewsusing#2Phillipsdriver.See Figure 8.

Page 4

US LED

Updated 09.26.13

CNPx-50INSTALLATION GUIDE

#44-000017

1. Turn off main power.

2. Secure driver box assembly to mounting bracket by tightening mounting screws using ¼” hex driver. See Figure 9.

3. Secure mounting bracket to any vertical wall using #10 sheet metal screws supplied. Insure location allows wire harness to reach low voltage side of power supply box. See Figure 10.

4. Make internal primary side (high voltage) power connections by connecting wires, Black to Load, White to Neu-tral and Green to Ground using approved electrical connector. See wire diagrams.

5. Make secondary (low voltage) connections by using approved electrical connector. See wire diagrams.

6. Secure driver box top using #8 sealing machine screws supplied.

7. Turn on power.

INSTALLATION INSTRUCTIONS - DRIVER BOX

FIG 9 FIG 10

Mounting screws

INSTALLATION GUIDECNPx-50

Page 5

US LED

Updated 09.26.13

#44-000017

WIRING DIAGRAMS

WITH TRANSFORMER

WITHOUT TRANSFORMER

FOR CNP1-50 LUMINAIRES

Page 6

US LED

Updated 09.26.13

CNPx-50INSTALLATION GUIDE

#44-000017

WITHOUT TRANSFORMER, 2 DRIVERS

WIRING DIAGRAMS

WITH TRANSFORMER, 2 DRIVERS

FOR CNP2-50 LUMINAIRES

SURFACE MOUNT KIT INSTALLATION GUIDECNPx-50

Page 1

Updated 03.28.14

The installation must only be performed by a licensed electrician.

To prevent death, injury or damage to property, this product must be installed in accordance to National Electrical Code (NFPA70) in the US or Canadian Electrical Code (CSA22.1) in Canada.

Disconnect power before installing the product or servicing it.

Wait until fixture has cooled down before installing or servicing the fixture.

MIN. 90°C SUPPLY CONDUCTORS

WARNINGl

l

l

l

l

1. Mount the Hinge, Latch, Driver Bracket, and Driver Assembly to the Plate using Hex Locknut with nylon SS 8-32 (Fig 1).

2. Install mounting plate assembly by folding mounting tabs in, insert mounting plate into 4” hole and secure by tightening mounting tab screws using #2 Phillips screw (Fig 2).

FIG 1 FIG 2

FIG 3

3. Hang Canopy Fixture on mounting plate assembly by hooking hinge on mounting plate hook. Secure by sliding locking plate forward into slot and tightening #6-32 locknut. Swing fixture into place and securing with mount-ing screws using #2 Phillips driver (Fig 3).

Page 2

Updated 03.28.14

CNPx-50SURFACE MOUNT KIT INSTALLATION GUIDE

4. Route wires through center of mounting plate assembly. Take wire harness assembly and make power connections using approved electrical connector. Pack excess wire in center of mounting plate assembly and mount cover using #10 sealing weather resistant screws supplied (Fig 4).

5. Mount the Base of the Canopy Star Surface Mount Kit using Hex Washer HD Sheet Metal Screws, STL #10, 1” (Fig 5).

6. Mount the CanopyStar Surface Mount Plate Assembly to the Base using #10, .500, Zinc-Plated Steel Screw (Fig 6).

FIG 4 FIG 5

FIG 6


Top Related