7/28/2019 Cema Catalog
1/6
7/28/2019 Cema Catalog
2/6
CEMA B BALL BEARING SERIES
20 DEG TROUGHING IDLER BW-B34202 4 DIAMETER ROLL
20 DEG TROUGHING IDLER BW-B35202 5 DIAMETER ROLL
35 DEG TROUGHING IDLER BW-B34352 4 DIAMETER ROLL
35 DEG TROUGHING IDLER BW-B35352 5 DIAMETER ROLL
20 DEG. TROUGHING TRAINING IDLER BW-CSLB34TR200 4 DIAMETER ROLL
7/28/2019 Cema Catalog
3/6
CEMA B BALL BEARING SERIES
FLAT CARRYING IDLER BW-B142 & BW-B152 4 & 5 DIAMETER ROLL
RETURN IDLER BW-B142 & BW-B152 4 & 5 DIAMETER ROLL
48
Consult factory for rubber disc return idlers.
20 DEG. TROUGHING TRAINING IDLER BW-CSLB35TR200 5 DIAMETER ROLL
35 DEG. TROUGHING TRAINING IDLER BW-CSLB34TR350 4 DIAMETER ROLL
35 DEG. TROUGHING TRAINING IDLER BW-CSLB35TR350 5 DIAMETER ROLL
7/28/2019 Cema Catalog
4/6
CEMA B BALL BEARING SERIES
35 DEG. CHANNEL MOUNT IDLER BW-B34352CM & BW-B35352CM 4 & 5 DIAMETER ROLL
20 DEG. CHANNEL MOUNT IDLER BW-B34202CM & BW-B35202CM 4 & 5 DIAMETER ROLL
20 DEG. IMPACT CHANNEL MOUNT IDLER BW-CSLB35A200CM 5 DIAMETER ROLL
Dimensions in inches. Weight in pounds. All dimensions approximate. Obtain certified drawings for exact dimensions.For wide base troughing idlers, add W to the end of the part number.
35 DEG. IMPACT CHANNEL MOUNT IDLER BW-CSLB35A350CM 5 DIAMETER ROLL
RETURN TRAINING IDLER BW-CSLB140TR & BW-CSLB150TR 4 & 5 DIAMETER ROLL
7/28/2019 Cema Catalog
5/6
CEMA B Series Roll Design Features
The inner shield acts
flinger to divert contamin
away from the bearing ca
Two-piece shield fo
a horizontal, grease f
labyr inth and provi
a barrier to contamin
entering the bearing cav
The back seal is molded
into the head design and
provides added protection
for the bearing cavity.
Engineered polymer roll
end provides a lightweight roll
that reduces noise, corrosion
and material build-up.
The outer shield locks t
shaft to maintain horiz
labyrinth clearances.
A 17mm ball bearing
is double shielded and
permanently lubricated.
An interference press fit sec
the roll end to the shell.
StylesGoodman Conveyor manufactures its B Series idlers for belt widths from 18 through 48. Troughing idlers
offered in 20 and 35 trough angles (45 also available) in standard and wide base, as well as inside cha
mount designs.
4 and 5 Diameter RollsThe 4 and 5 diameter rolls are of one-piece construction with steel shells and an engineered polymer roll
The roll end is secured by an interference press fit and is locked to the shaft. The 17mm shaft provides stre
and the short moment arm minimizes shaft slope at the bearing which increases bearing life. Rolls are fitte
each end with a special 17mm deep groove, high capacity, precision ball bearing. These bearings are do
shielded and permanently lubricated.
Removable RollsRolls are secured in the frame assembly by special clips providing a rigid, one-piece unit, yet allowing easy
removal when necessary.
Rigid End and Center StandsEnd and center stands are die formed from steel plate, and end stands are channel formed for greater rig
Stands and foot plates are fixture-welded to the self-cleaning inverted base angle, assuring accurate
alignment.
17mm Solid Shaft
7/28/2019 Cema Catalog
6/6
Goodman products pictured, described, or listed in this publication are illustrative only.
Application and use of these products must be in accordance with applicable codes
and regulations and must be arranged and/or provided with covers or other guards
where necessary to assure safety of personnel.
GOODMAN CONVEYOR COMPANYP.O. Box 866 / 645 Floyd Wright Drive
Belton, South Carolina 29627
(864) 338-7793 / Fax (864) 338-8732
WEBSITE: www.goodmanconveyor.com
E-MAIL: [email protected]
Printed in U.S.A.
Ball Bearing 5/07