Clipping Lines
Lecture 7Wed, Sep 10, 2003
The Graphics Pipeline
From time to time we will discuss the graphics pipeline.The graphics pipeline is the sequence of operations that are performed on primitives to render them on the screen as collections of colored pixels.We have discussed the framebuffer.Now we will discuss 2-dimensional clipping of lines.
Clipping
Any object that is not entirely within the viewport must be clipped.That is, the part that is outside the viewport must be eliminated before the object is drawn.The graphics pipeline, does this “automatically.”Why is it necessary to clip?
Clipping Lines
If a line is partially in the viewport, then we need to recalculate its endpoints.In general, there are four possible cases. The line is entirely within the viewport. The line is entirely outside the viewport. One endpoint is in and the other is out. Both endpoints are out, but the middle
part is in.
Clipping Lines
Before clipping
F
A
B
C
D
E
G
H
Clipping Lines
After clipping
F
A
B
E
G
H
F'
G'
H'
C
D
The Cohen-Sutherland Clipping Algorithm
Let the x-coordinates of the window boundaries be xmin and xmax and let the y-coordinates be ymin and ymax.
xmin xmax
ymin
ymax
The Cohen-Sutherland Clipping Algorithm
For each endpoint p of a line segment we will define a codeword c3c2c1c0 consisting of 4 true/false values. c3 = true, if p is left of the window. c2 = true, if p is above the window. c1 = true, if p is right of the window. c0 = true, if p is below the window.
How many different values are possible for a codeword?
The Cohen-Sutherland Clipping Algorithm
How many different combinations of values are possible for the codewords of the two endpoints of a segment?How do we compute a codeword?
The Cohen-Sutherland Clipping Algorithm
Consider the vertical edge x = xmin. (You can do the other edges.)Compare the x-coordinate of p to xmin.If it is less, then “set” bit 3 of the codeword.if (p.x < xmin)
c = 1 << 3;
The Cohen-Sutherland Clipping Algorithm
After the codewords for both endpoints are computed, we divide the possibilities into three cases: Trivial accept – both codewords are
FFFF. Trivial reject – both codewords have T
in the same position. Indeterminate so far – Investigate
further.
The Cohen-Sutherland Clipping Algorithm
What is the quickest way to separate the cases? Use bitwise “and” and “or.”
If ((codeword1 | codeword2) == 0) then we trivially accept. Why?
If ((codeword1 & codeword2) != 0) then we trivially reject. Why?
The Cohen-Sutherland Clipping Algorithm
What about the third case?We clip against each edge of the window, in sequence, as necessary.After clipping against an edge, we may test again for trivial acceptance or trivial rejection before moving on to the next edge.
The Cohen-Sutherland Clipping Algorithm
The Cohen-Sutherland Clipping Algorithm
clip
The Cohen-Sutherland Clipping Algorithm
clip
The Cohen-Sutherland Clipping Algorithm
clip
The Cohen-Sutherland Clipping Algorithm
clip
The Cohen-Sutherland Clipping Algorithm
The Cohen-Sutherland Clipping Algorithm
This raises some questions? What is the worst case? What is the best case? How do we decide whether to clip
against a particular edge? If we do clip, how to we determine the
new endpoint?
The Cohen-Sutherland Clipping Algorithm
Consider again the vertical edge x = xmin. (You can do the other edges.)Compute codeword1 ^ codeword2.This shows where they disagree. Why?
“And” this with (1 << 3). If result = 1, then clip. Else do not clip.
The Cohen-Sutherland Clipping Algorithm
If we clip, then the new point will be on the line x = xmin.So its x-coordinate will be xmin.We must calculate its y-coordinate.
The Cohen-Sutherland Clipping Algorithm
p
q
r
x = xmin
The Cohen-Sutherland Clipping Algorithm
p
r
x = xminq
The Cohen-Sutherland Clipping Algorithm
p
r
xmin – p.x q.x – p.x
q.y – p.y
r.y – p.y
x = xminq
The Cohen-Sutherland Clipping Algorithm
Then(r.y – p.y)/(xmin – p.x) = (q.y – p.y)/(q.x –
p.x)
Sor.y = p.y + (xmin – p.x)(q.y – p.y)/(q.x –
p.x)
The Cohen-Sutherland Clipping Algorithm
This used to be done in software.Now it is done in hardware, in the graphics pipeline.Should it be done before or after the line is rasterized?We will discuss clipping polygons and clipping in 3D later.
Example: Clip a Line
LineClipper.cpp