Note: This manual is written in English. It is for use only by people that can read, speak and understand English. In addition, the operators of the attachment (compactor) must also read, speak and understandEnglish
IHC50 IHC75
COMPACTOR MANUAL
YOUR PARTNERS IN DEMOLITION
IHC150 IHC250
2Compactor Manual
3 WARRANTY4 PREFACE5 DECLARATION OF CONFORMITY 6 I SAFETY INFORMATION
Precautions 6-9
Safety Decals 10
Airbore Noise 11
12 II TECHNICAL SPECIFICATIONSIHC50 12
IHC75 13
IHC150 14
IHC250 15
16 III EXPLODED VIEW AND PARTS LISTIHC50 16-17
IHC75 18-19
IHC150 20-21
IHC250 22-23
24 IV VALVE & HOSE PARTS AND INSTALLATIONValve function and operation (IHC75, 150) 24
HVFK050F000 Manifold Assembly with Fittings 25-26
27 V COMPACTOR INSTALLATIONPreping the Carrier 27
Setting Up Compactor 28
Trouble Shooting 29
Compactor Installation Record 30
30 VI COMPACTOR OPERATION Initial & Normal Operation
31 VII COMPACTOR MAINTENANCE (Daily, Weekly, 500 Hours)
32 VIII COMPACTOR ECCENTRICAssembly Procedure 33
Cross Section 34
TABLE OF CONTENTS
37/9/2014
INDECO NA 135 Research Drive Milford, CT 06460
Standard New Compactor Limited Warranty
INDECO N.A. warrants New Indeco Compactors to be free of defects in materials or workmanship subject to the following terms and conditions.
1) Warranty period shall be 12 months from date of first installation.
2) This Warranty covers Labor as listed in the INDECO Flat Rate Schedule at 75% of the Distributorsshop labor rate.
3) This Warranty covers Compactors used in accordance with published INDECO maintenance andoperation procedures.
4) This warranty does not cover failures determined by INDECO to be due to lack oflubrication, improper installation, poor maintenance or improper operation.
5) This warranty does not cover the replacement of Wear Items.The following parts are considered to be Wear Items:
Shock Absorbers
6) This Warranty does not cover the replacement of service items during the course of normalmaintenance.The following parts are considered Service Items:
O-rings Seals
7) This warranty does not cover loss of operating time, loss of use or other consequential damageswhile the Compactor is out of service.
8) The repair or replacement of parts during the warranty period does not prolong this warranty.
9) This Warranty does not cover, or include, items sold with, or attached to, the Compactor.Examples: Grease Pumps, Hydraulic Kits and Hoses.
10) Use of Non INDECO OEM Spare parts will terminate this warranty.
11) Altering or modifying of the Compactor without the written approval by INDECO will terminate thiswarranty and any obligations under this warranty.
12) Warranty Registration: INDECO assumes no liability for warranty request submitted for productsfor which a New Product Warranty Registration form has not been completed and submittedto INDECO within 60 days from the time of first installation of the Compactor. Any warrantyrequest submitted for a product for which INDECO does not have a New Product WarrantyRegistration form on file will be denied.
INDECO does not authorize any other person or company to assume its liability in connection with the sale or use of its products. WAR-0010-CREV 01-01-10
3 WARRANTY4 PREFACE5 DECLARATION OF CONFORMITY 6 I SAFETY INFORMATION
Precautions 6-9
Safety Decals 10
Airbore Noise 11
12 II TECHNICAL SPECIFICATIONSIHC50 12
IHC75 13
IHC150 14
IHC250 15
16 III EXPLODED VIEW AND PARTS LISTIHC50 16-17
IHC75 18-19
IHC150 20-21
IHC250 22-23
24 IV VALVE & HOSE PARTS AND INSTALLATIONValve function and operation (IHC75, 150) 24
HVFK050F000 Manifold Assembly with Fittings 25-26
27 V COMPACTOR INSTALLATIONPreping the Carrier 27
Setting Up Compactor 28
Trouble Shooting 29
Compactor Installation Record 30
30 VI COMPACTOR OPERATION Initial & Normal Operation
31 VII COMPACTOR MAINTENANCE (Daily, Weekly, 500 Hours)
32 VIII COMPACTOR ECCENTRICAssembly Procedure 33
Cross Section 34
WARRANTY
4Compactor Manual
Manufacture and address:
Indeco North America 135 Research Drive Milford Connecticut, 06460 U.S.A.
We declare under our sole responsibility that the product described as:
Machine description: Hydraulic compactor
Make: Indeco
Type: IHC50, IHC75, IHC150 and IHC250
Serial number: /
Complies with the requirements of the following directive:
Machinery Directives 98/37
Standards considered:
EN 21200-1, EN 12100-2
Date January 1, 2010
Chief Executive Officer, Signature
DECLARATION OF CONFONFORMITY
57/9/2014
Congratulations on your purchase of this fine INDECO product. To best utilize the advanced technology engineered into our attachments, we recommend you take the time to famil-iarize yourself with this manual and the attachment. The information in this manual will ensure long life, high productivity and minimum downtime from this attachment. Because we want you to be pleased with your decision to purchase our products, compactor owners should strictly adhere to the information and technical specifications contained within this manual.
The INDECO Hydraulic Compactor is simply a machine, and like any other machine, is de-signed to perform within specified guidelines. The compactor takes the hydraulic energy created by the carrier pumps (excavator, tractor loader backhoe, etc.) and converts this energy into mechanical or kinetic energy. Therefore, the perfect match of hydraulic compac-tor to carrier is essential in order to produce maximum performance of the compactor. If the hydraulic energy (oil pressure, oil flow and return oil pressure between carrier and the com-pactor) is outside the INDECO specifications contained herein, then the compactor’s me-chanical energy will also be incorrect. Statistics show that 90% of all compactor problems can be traced back to incorrect mechanical or hydraulic installation to the carrier.
While every attempt has been made by INDECO to manufacture a superior product, we cannot install the compactor. It is up to the dealer to ensure that compactors are installed within the enclosed correct parameters for their particular carrier.
To further ensure maximum productivity and longevity of INDECO compactors,we recommend:
• Adherence to INDECO’s daily, weekly and annual compactor maintenance programs (enclosed)• Regular replacement of carrier hydraulic filters (especially in dusty conditions)• Always check compactor circuit flows and pressures when the carrier is changed• Annual checks of compactor circuit flows and pressures
If problems with the compactor do occur, we have made every attempt to include any even-tuality in this Owner’s Manual. Most problems can be easily remedied due to the cause-and-effect nature of these machines. We have also done our best to ensure correctness of the information within. However, the manufacturer reserves the right to update this manual subject to the technological development of the product and service.
PREFACE
6Compactor Manual
• The dealer must instruct user on proper and safe operation before delivery of this compactor.
• Wear safety glasses, hard hat and noise protection while operating compactor.
• Operate compactor only while inside of cab of machine.
• Keep all personnel well clear of machine and compactor while in operation.
• Install a safety protection device between operator and compactor.
• Use common sense when using this compactor. Flying stone chips can injure or even kill.
Safety Precautions
Before operating this INDECO Hydraulic Compactor, please read carefully the enclosed information. If you have any questions consult your INDECO dealer for more information.
I SAFETY INFORMATION
77/9/2014
Carefully read the following safety precautions. Make sure you fully under-stand them. Failure to follow a safety warning or recognize and rectify a safety hazard could result in injury of death to you or others around you. In general, always use common sense in your work habits and keep your tools and equipment in good operating condition.
Use trained personnel
Allow only trained personnel to operate or service this equipment. Read and understand all safety precautions listed in the Indeco manual and in the Carrier manual.
Flying objects or high-pressure fluid hazards
Do not operate Indeco equipment with personnel in the immediate proxim-ity of the equipment because of possible flying objects of high-pressure fluid hazards. The operator’s compartment should have the necessary protective guards to prevent entry of flying or falling objects.
Wear correct safety protection
Verify that all personal wear protective headgear, eye protection and steel toe boots. In dusty conditions, wear a respirator to protect against dust. Do not wear loose fitting clothing or jewelry while working on the machine.
Pay attention to your hands when mounting the compactor
Keep your fingers clear when inserting mounting pins. Do not use your fingers to “feel” pin alignment. Unexpected boom or equipment movement could result in injury and possible loss of your fingers. Instruct the operator to touch the controls only when instructed.
I SAFETY INFORMATION
8Compactor Manual
Relieve system pressure prior to working on equipment
Escaping fluid under pressure can penetrate the skin causing serious injury.
To avoid any risk, be sure to relieve the pressure before disconnecting hydraulic lines. Consult the operator’s manual of the carrier for the proper procedure for relieving pressure.
Important checkpoints before operation
√ Tighten all hydraulic fittings before applying pressure.
√ Keep hands and body away from pinholes and nozzles that eject fluid under high pressure.
√ Do not use your hands to search for leaks. Use a piece of paper.
Operation and maintenance precautions
Never activate the compactor unless the operator is in full control of the carrier and is seated in the operator’s seat.
Do not operate the compactor above 180°F (82 C) hydraulic oil temperature.
Do not make any alterations to the compactor without authorization from Indeco Product Support Department.
Make frequent visual inspections of fasteners, attaching pins, hoses and rubber isolators.
Use caution when torquing fasteners, do not over torque. Adhere to SAE torque specifications only. A previously overstress part may fail later.
I SAFETY INFORMATION Precautions
97/9/2014
Major compactor components are heavy. Always use an adequate lifting device. Never mount the compactor on a carrier that cannot adequately handle the compactor weight.
For nighttime operation, the carrier should offer adequate lighting for safe operation during compacting, repositioning of transporting (European harmonized standard EN-500-0 paragraph 5.1).
Never use the compactor as part of a lifting device, additional weight could cause the carrier to tip over or cause damage to the compactor components
Be cautious of flying metal particles when striking any hardened parts with a hand held tool.
Operate the compactor aware of the effects the vibrations may have on trench walls and never operate the compactor in a trench with personal working nearby in the trench at the same time.
Never service or work on the compactor in an open trench of other unsafe area.
Always clean up oil spills.
Do not over compact near buried utilities or foundations; serious damage to utilities or foundations could result.
Keep personnel clear of the full range of swing, reach, height, depth of carrier boom while operating or positioning the compactor. During standby periods, always lower carrier boom so the compactor rests firmly on the ground and turn off the carrier engine.
Make sure that a window of protective screen is in place on the carrier to fully protect the operator against flying objects.
I SAFETY INFORMATION Precautions
10Compactor Manual
Maintain safety decals
Always replace any safety or warning decals that become damaged of illegible. Replace all safety of warning decals when repainting the equiment. These decals are available from your Indeco dealer or from Indeco.
I SAFETY INFORMATION Safety Decals
117/9/2014
Statement of conformity with Directive 98/37/EC
Indeco North America, 135 Research Drive, Milford Connecticut, USA, as manufacturer and keeper of technical documentation, declares under its own responsibility that the Indeco Compactor, models IHC50, IHC75, IHC150 and IHC250 conforms with the essen-tial health and safety requirements of framework directives 98/37/EC and successive modifications, has the following measured sound levels;
SOUND POWER LEVEL (MEASURED)
Continuous A-weighted sound pressure level at workstationsExceeds 70 dB (A) at 38.1 meters (125 feet)
Sound power level emitted by machinery where the equivalent continuous A-weighted sound pressure level at workstations. Exceeds 85 dB (A) at 13.7 meters (45 feet)
1-18-2010 PTU, IHC150 compactor
I SAFETY INFORMATION Airbore Noise
12Compactor Manual
Carrier weight: 703-2,994 kg1,550-6,600 lbs
Operating weight 176 kg389 lbs
Height 559 mm 22 in
Width 457 mm18 in
Base Plate 457 mm x 762 mm x 25.5 in. thick18 in x 30 in x 1 in thick
Base Plate Thickness 25.5 mm1 in
Auxiliary, Bolt-on, Base Plate Standard with unit 305 mm x 762 mm x 13 mm thick12 in x 30 in x .05 in thick
Oil Supply Range 45-68 l/min12-18 GPM
Maximum Operating Pressure 240 bar3,500 psi
Maximum Back Pressure 7 bar100 psi
Force @ Maximum Frequency 2,542 kg5,604 lbs
Frequency 33.3-50 Hz2,000-3,000 vpm
Reservoir Capacity(85/90W Gear Oil)
1.0 l.0.34 gal.
NOTE: Dimensions are nominal and are for reference only
II TECHNICAL SPECIFICATIONSIHC50
137/9/2014
Carrier weight: 4,082 - 12,701 kg.9,000 – 28,000lbs
Operating weight 396 kg875 lbs
Height 600 mm 23.5 in
Width 635 mm.25.0 in
Base Plate 635 mm x 838 mm25.0 in x 33.0 in
Base Plate Thickness 32 mm1.25 in
Oil Supply 76 l/min20 GPM
Maximum Operating Pressure 200 bar3000 psi
Maximum Back Pressure 21 bar300 psi
Force @ Maximum Frequency 3,350 kg 7,386 lbs
Frequency 33 Hz2,000 vpm
Reservoir Capacity(85/90W Gear Oil)
4.7 l.1.23gal.
NOTE: Dimensions are nominal and are for reference only
II TECHNICAL SPECIFICATIONSIHC75
14Compactor Manual
Carrier weight: 7,711 – 21,773 kg.17,000 – 48,000 lbs
Operating weight 799 kg.1762 lbs.
Height 800.1 mm 31.50 in.
Width 710 mm.28.0 in.
Base Plate 710 mm x 1016 mm28.0 in x 47.0 in
Base Plate Thickness 38 mm1.50 in
Oil Supply 121 l/min32 GPM
Maximum Operating Pressure 200 bar3,000 psi
Maximum Back Pressure 21 bar300 psi
Force @ Maximum Frequency 7,388 kg16,287 lbs
Frequency 33 Hz2,000 vpm
Reservoir Capacity(85/90W Gear Oil)
4.8 l.1.27 gal.
NOTE: Dimensions are nominal and are for reference only
II TECHNICAL SPECIFICATIONSIHC150
157/9/2014
Carrier weight: 20,412-45,360 kg.45,000 – 100,000lbs
Operating weight 996 kg2,196 lbs
Height 785 mm 31.0 in
Width 889 mm.35.0 in
Base Plate 889 mm x 1207 mm35.0 in x 47.5 in
Base Plate Thickness 38 mm1.50 in
Oil Supply Range 189-265 l/min50-70 GPM
Maximum Operating Pressure 170 bar2,500 psi
Maximum Back Pressure 7 bar100 psi
Force @ Maximum Frequency 16,090 kg35,473 lbs
Frequency 30-37 Hz1,800-2,200 vpm
Reservoir Capacity(85/90W Gear Oil)
9 l.2.46 gal.
NOTE: Dimensions are nominal and are for reference only
II TECHNICAL SPECIFICATIONSIHC250
16Compactor Manual
Ref # Qty Description Part #1 1 Hydraulic Motor (12-18 GPM) Standard VC21308DSA
2 1 Bearing Carrier (Motor Side) CM-50-MSRP-C
3 1 Snap Ring 350011
4 2 Eccentric Bearing VC9201555
5 1 Eccentric VC9194550
6 1 Bearing Carrier (Opposite Motor) CM-50-BSRP-C
7 4 Isolator VC9085000
8a 1 Reservoir Plug HW14196
8b 1 Vent Plug HV1U577
9 1 Base Plate Assembly 18” Bolt On Base Plate CM-50-BASE
10 1 18” Bolt On Base Plate CM-50-18-BASE
11 1 Gear Oil - HD 80-90 LITER
12 1 Upper Mounting Frame CM-50-TB-ASM
13 2 Rubber Bumper VC-XX1528
14 1 Bulkhead Fitting - 90 Degree HF-2043-1212
15 1 Bulkhead Fitting - Straight HF-2040T-1212
16 2 Fitting - Motor HF-2062-1212
III EXPLODED VIEW AND PARTS LISTIHC50 SERIAL NUMBER C230106 AND AB0VE
27
12
13 20
14
15
19
18
7
21
25
1617
27
177/9/2014
III EXPLODED VIEW AND PARTS LISTIHC50 SERIAL NUMBER C230106 AND AB0VE
Ref # Qty Description Part #17 2 O-Ring 100173
18 1 Hose - Rear Motor Fitting to Left Bulkhead Fitting HH-50-14US
19 1 Hose - Front Motor Fitting to Right Bulkhead Fitting HH-50-16US
20 4 Lock Nut - 5/16” HW36602
21 32 Lock Nut - 3/8” HW-NSL102
22 6 Lock Nut - 1/2” HW39606
23 AS REQUIRED Flat Washer - 1/4” HW-39701
24 22 Lock Washer - 3/8” HW39605
25 40 Washer - 3/8” HW-FWL210
26 2 Washer - 1/2” HW39754
27 16 Bolt - Special - 3/8” x 1.0” - Outer Shock HW-IHC050-ISOL
28 2 Bolt - 1/4” x 28 x 3/4” HW-HC8602
29 8 Bolt - 3/8” x 7/8” - Bearing Carrier HW-HC8161
30 2 Bolt - 3/8” x 1.0” - Motor HWHC8163
31 16 Bolt - 3/8” x 1-1/4” - Inside Shock HW-HC5162
32 6 Bolt - 1/2” x 2.0” - Base Plate HW-HC8220
33 12 Flat Washer - 1/2” HW39754
9
5
4
2
3
1
6
7
24
8b
25
24
232233
10
2429
4
31
29
28
8a
30
18Compactor Manual
III EXPLODED VIEW AND PARTS LISTIHC75
Ref # Qty Description Part #1 1 Motor VC9081504-WS
2 32 Bolt - ¾” - 10 x 2-¼” HW8292
3a 2 Bolt - ½” - 13 x 7/8” HW8215
3b 14 Bolt - ½” - 13 x 1-½” HW30114
4a 20 Washer - ½” HW-39754
4b 64 Washer - ¾” HW-FW207
5 32 Lock Nut - ¾”-10 HW-NS107
6 2 Eccentric Bearing VC9201500
7 1 Eccentric CM-75-ECCA-C
8 1 Snap Ring VC9100065
9 1 Base Assembly CM-75-B-C
10 4 Isolator VC9082000
11 1 Bearing Carrier (opposite motor) CM-75-BSRC-C
12 1 Bearing Carrier (motor side) CM-75-MSRP-C
13 2 Reservoir Plug - ½”- 20 HW14196
1
3b
4a
9
8
6
7
12
13 6
11
3a
3b 4a
2 4b 5
10
2
3b
197/9/2014
III EXPLODED VIEW AND PARTS LISTIHC75
Ref # Qty Description Part #14 1 Manifold/Assembly See Page 22
15 2 Clamp Kit HW-FF593-16
16 1 Upper Mounting Frame CM-75-TB-ASM
17 2 Bulkhead Fitting HF2041-1212
18 4 Fitting (valve) HF202702-1212
19 1 Hose - Manifold “OUT” Port to Bulkhead HH-75-19US
20 1 Hose - Manifold “IN” Port to Bulkhead HH-75-23US
21 1 Hose - Manifold “B” Port to Front Motor Port HH-75-24US
22 1 Hose - Manifold “A” Port to Rear Motor Port HH-75-18US
23 2 Bolt HW8175
24 4 Washer HW-FW202
25 2 Lock Nut HW-NS102
15
1521
22
252423
16
17
19
20
14
20Compactor Manual
A
B
A
B
B1
A1
3
G OUT
D1
D3
G IN
B
A
G IN
4
1
2
IN
D2
OUT
Including Serial Numbers:
IV VALVE & HOSE PARTS LIST & INSTALLATIONHVFK032F000 Manifold Assembly with FittingsFitting and port identification (IHC75)
27
30
28
29
26
NOTE: Single character callouts identify ports and/or cavities
217/9/2014
Ref # Qty Description Part #26 1 Flow Valve Manifold HVFK032F32
27 1 Relief Valve - Port “3” HVRV1226A0
28 1 Flow Valve Cartridge- Port “2” HVFR1630F0-N-20
29 5 Plug HF-FF2138-06
30 1 Check Valve - Port #1 HVCV16200N5
On current production Indeco compactors, models IHC75 and IHC150, they are factory equipped with a flow control valve with an integral relief bypass circuit. The flow control valve limits the maximum flow that can be delivered to the motor on the compactor. 20 GPM for the IHC75, 32 GPM for the IHC150. The relief valve limits the maximum operating pressure of the system. The check valve allows hydraulic oil to bypass from the return side of the motor to the supply side of the motor. This is a safety feature to prevent premature failure of the motor if the compactor is shut-off abruptly at high speed (full flow).
The case drain only needs to be connected when the circuit-return pressure exceeds the maximum allowable pressure. Install a hose from the case drain port on the valve to the hydraulic tank on the carrier. Ports D1 and D2 are isolated spare ports to be used as a through connection passage for a case drain if needed.
Including Serial Numbers:
IV VALVE & HOSE PARTS LIST & INSTALLATIONHVFK032F000 Manifold Assembly with FittingsFitting and port identification (IHC75)
22Compactor Manual
III EXPLODED VIEW AND PARTS LISTIHC150
Ref # Qty Description Part #1 1 Motor VC9310001-WS
2 32 Bolt - ¾” - 10 x 2-¼” HW8292
3a 2 Bolt - ½” - 13 x 7/8” HW8215
3b 18 Bolt - ½” - 13 x 1-½” HW30114
4a 36 Washer - ½” HW-FW204
4b 64 Washer - ¾” HW-FW207
5 32 Lock Nut - ¾”-10 HW-NS107
6 2 Eccentric Bearing VC9325500
7 1 Eccentric CM-150-ECCA-C
8 1 Snap Ring VC9100130
9 1 Base Assembly CM-150-BASE
10 4 Isolator VC9338000
11 1 Bearing Carrier (opposite motor) VC9322560
12 1 Bearing Carrier (motor side) VC9322550
13 2 Reservoir Plug - ½”- 20 HW14196
1
3b
4a
9
8
6
7
12
13 6
11
3a
3b 4a
2 4b 5
10
2
3b
237/9/2014
III EXPLODED VIEW AND PARTS LISTIHC150
Ref # Qty Description Part #14 1 Manifold/Assembly See Page 22
15 2 Clamp Kit HW-FF593-16
16 1 Upper Mounting Frame CM-150-TB-ASM
17 2 Bulkhead Fitting HF2041-1616
18 4 Fitting (valve) HF202702-1616
19 1 Hose - Manifold “OUT” Port to Bulkhead HH-150-35US
20 1 Hose - Manifold “IN” Port to Bulkhead HH-150-38US
21 1 Hose - Manifold “B” Port to Front Motor Port HH-150-24US
22 1 Hose - Manifold “A” Port to Rear Motor Port HH-150-19US
23 2 Bolt HW8175
24 4 Washer HW-FW202
25 2 Lock Nut HW-NS102
15
1521
22
252423
16
17
19
20
14
24Compactor Manual
A
B
A
B
B1
A1
3
G OUT
D1
D3
G IN
B
A
G IN
4
1
2
IN
D2
OUT
Including Serial Numbers:
IV VALVE & HOSE PARTS LIST & INSTALLATIONHVFK032F000 Manifold Assembly with FittingsFitting and port identification (IHC150)
27
30
28
29
26
NOTE: Single character callouts identify ports and/or cavities
257/9/2014
Ref # Qty Description Part #26 1 Flow Valve Manifold HVFK032F32
27 1 Relief Valve - Port “3” HVRV1028AON-35
28 1 Flow Valve Cartridge- Port “2” HVF030F032C
29 5 Plug HF-FF2138-06
30 1 Check Valve - Port #1 HVCV16200N5
On current production Indeco compactors, models IHC75 and IHC150, they are factory equipped with a flow control valve with an integral relief bypass circuit. The flow control valve limits the maximum flow that can be delivered to the motor on the compactor. 20 GPM for the IHC75, 32 GPM for the IHC150. The relief valve limits the maximum operating pressure of the system. The check valve allows hydraulic oil to bypass from the return side of the motor to the supply side of the motor. This is a safety feature to prevent premature failure of the motor if the compactor is shut-off abruptly at high speed (full flow).
The case drain only needs to be connected when the circuit-return pressure exceeds the maximum allowable pressure. Install a hose from the case drain port on the valve to the hydraulic tank on the carrier. Ports D1 and D2 are isolated spare ports to be used as a through connection passage for a case drain if needed.
Including Serial Numbers:
IV VALVE & HOSE PARTS LIST & INSTALLATIONHVFK032F000 Manifold Assembly with FittingsFitting and port identification (IHC150)
26Compactor Manual
III EXPLODED VIEW AND PARTS LISTIHC250
1 1 Base Plate Assembly CM-250-B-C
2 1 Bearing Carrier (opposite motor) CM-250-BSBR-C
3 1 Eccentric CM-250-ECCA-C
4 1 Bearing Carrier (motor side) CM-250-MSBR-C
5 2 Eccentric Bearing VC9337000
6 1 Snap Ring VC9100200
7 1 Motor VC9306930
8 2 Bolt ½” - 13 x 1.25” HW-HC8217
9 36 Washer ½” HW-39754
10 18 Bolt ½” - 13 x 1.50” HW-30114
11 2 Bolt 5/8” - 11 x 1.50” HW-8264
12 2 Washer 5/8” SAE G8 HW-FWA206
13 2 Reservoir Plug HW14196
7
1211
4
53
1 5
13
2
98
910
6
10 9
277/9/2014
III EXPLODED VIEW AND PARTS LISTIHC250
16
17
18
18
15
14
19
20
22
23
21
14 1 Bracket Top CM-250-TB-ASM
1 Hose Kit IHC-250 Hose Kit Long-R
15 2 Bulkhead Fitting HF2041-1616
16 1 Hose Lower Motor Port to Left Front Bulkhead Fitting HH-250-38US
17 1 Hose Front Motor Port to Right Front Bulkhead Fitting HH-250-27US
18 2 Clamp Kit HW-FF593-16
19 4 Isolator VC9338000
1 Bolt Kit, Isolator HWIHC-250-ISO
20 16 Shock Absorber Bolt - ¾” - 10 x 2.5 HW-8293
21 76 Washer - ¾” FLAT SAE G HW-FW-207
22 32 Lock Nut - ¾” - 10 SAE G8 HW-NS-107
23 16 Shock Absorber Bolt ¾” - 10 x 2.25d HW8292
28Compactor Manual
IV HYDRAULIC MOTORRelief and Check Valve Operation
Release/Check Valve
Optional Case Drain Port
297/9/2014
The IHC250 hydraulic motor is equipped with a relief valve that limits the maximum operating pressure of the system. The check valve allows hydraulic oil to bypass from the return side of the motor to the supply side of the motor. This is a safety feature to prevent premature failure of the motor if the compactor is shut-off abruptly at high speed (full flow).
The case drain only needs to be connected when the circuit-return pressure exceeds the maximum allowable pressure. Install a hose from the case drain port on the motor to the hydraulic tank on the carrier.
NOTE: The Motor Relief Valve is preset at the factory. For any service issues with the valve, contact the Indeco North America Service Department.
IV HYDRAULIC MOTORRelief and Check Valve Operation
30Compactor Manual
V COMPACTOR INSTALLATIONInstallation Procedures for INDECO Hydraulic Compactors
Prepping the Carrier. Step one: Installing the Flow meter Install a Hydraulic Flow-meter into the Auxiliary Circuit that will be used to run the Compator. The Flow meter should be installed in place of the Compactor and not in line with the Compactor. Also tee a pressure gauge into the return line if your Flow meter does not have a gauge port on its Outlet.
Step two: With the Restrictor-valve on the Flow-meter turned to the fully open position, (fully closed on machines with closed center Hydraulics.) Start the machine and run at ½ to ¾ throttle.
Step three: Heating the Hydraulic oil. Engage the auxiliary circuit and turn the Flow-meter Restrictor-valve until the Flow-meter pressure gauge reaches approximately 1500 psi. Continue to run the machine until the hydraulic oil reaches an operating temperature of at least 150 degrees Farenhiet or 66 degrees Celsius. * Write this temperature on line F1 of the Compactor Installation Record on page 4.
The following steps should be done with engine rpm’s set at full throttle.
Step four: Setting the Circuit relief. When the Hydraulic oil has reached operating temperature, turn the Flow-meter Restrictor-valve in until the pressure no longer rises on the Flow-meter pressure gauge. This is the current setting of the relief valve for this auxiliary circuit. Using the pressure gauge on the Flow meter reset the circuit relief valve to between 500 and 800 psi above the operating pressure of the Compactor you are installing. * Write this pressure on line F2 of the Compactor Installation Record on page 4.
Compactor Circuit Relief SettingsIHC50 – IHC250 2500 psi
Step five: Setting the operating pressure. Using the Flow-meter Restrictor-valve reset the pressure on the Flow meter gauge to the operating pressure of the Compactor to be installed. * Write this on line F3 of the Compactor Installation Record on page 4.
Compactor Operating PressuresIHC50 – IHC250 2500 psi
317/9/2014
Step six: Checking the Flow With the Flow meter pressure gauge set at the operating pressure of the Compactor, read the Oil flow on the Flow-meter flow gauge. This must be with in the range of the Compactor you are installing.
Compactor Flow Specifications IHC50 15-42 gpmIHC75 20 gpmIHC150 32 gpmIHC250 50-70 gpm
Step seven: Setting the flow. If the Flow is not within the specified range for the Compactor being installed, it must be ad justed to within spec. Depending on the Auxiliary circuit being used, flow may be adjusted several different ways. Consult the carrier manufacturer or auxiliary kit manufacturer for the proper procedure for adjusting the flow. * After setting the flow, write it on line F4 of the Compactor Installation Record on page 4.
Step eight: Checking the Backpressure. With the flow properly adjusted and the Flow-meter pressure gauge still set to the operating pressure of the Compactor being installed, read the gauge, which is teed into the return line. This is the Backpressure reading for the circuit. * Write this pressure on line F5 of the Compactor Installation Record on page 4.
Compactor *Maximum* Back pressuresIHC50 100 psiIHC75 300 psiIHC150 300 psiIHC250 100 psi
If the Backpressure reading is too high, there is too much restriction in the return circuit. A case drain must be installed to prevent damage to the motor. Doing the following can decrease Return circuit pressure. 1) Increase the size of the Return hoses and tubes. 2) Make sure the return line runs directly back to tank and not back through the valve. 3) Make sure any return filters are clean. 4) Remove elbows and/or tight bends from the return circuit. 5) Make sure there are no kinks in the return tubes or hoses.
V COMPACTOR INSTALLATIONInstallation Procedures for INDECO Hydraulic Compactors
32Compactor Manual
Setting up the Compactor
Step nine: Check oil level in reservoir To check oil level, remove 3/8” NPT plug from the side of the oil reservoir on the base plate assembly. The operating oil level should be flush with the bottom of the plughole.. Step ten: Hooking up the hydraulic whip hoses. On all INDECO Compactors the Inlet on the Compactor is the Supply (pressure) and the Out let Port is the Return (tank). Make sure when hooking the hoses to the machine that they are installed in this fashion.
Step eleven: Running and checking the Compactor. Start the compactor slowly and check for operation. Check compactor and hydraulic connections for leaks.
Trouble shooting
Operating pressure too low. Recheck the flow and back pressure. Possibly insufficient oil flow Operating pressure too high. Recheck the flow and back pressure. Possibly excess oil flow to compactor and/or excessive restriction in return line.
Compactor does not cycle. Check to make sure Compactor whip hoses are connected correctly. (Left –Return, Right - Pressure)
Compactor runs too fast/slow. Recheck inlet flow with Flow meter.
V COMPACTOR INSTALLATIONInstallation Procedures for INDECO Hydraulic Compactors
337/9/2014
Use this information when filling out the Warranty Registration form (WAR-0001) you received with the Compactor.
Dealer Name & Address: ______________________________________
______________________________________
______________________________________
Compactor Model: ____________________ Serial #: __________________
Mounted on:
Machine Make: _______________ Model: __________ Serial # ___________
Flow meter readings: F1) Temperature of Hydraulic Oil (150°F min.) ____________________
F2) Circuit Relief Valve setting: ____________________
F3) Flow meter set to operating pressure of: ____________________
F4) Flow of auxiliary circuit set to: ____________________
F5) Backpressure of return circuit: ____________________
Technician completing Installation: ______________________ Date: _____________
The installation of the Compactor is now complete. These procedures should be followed whenever this Compactor is installed onto a machine to guaranty the best performance. Make a copy of this page for your records and then,
Mail, Fax or E-mail this page to: INDECO N.A. ATTN: Product Support Department 135 Research Drive Milford, CT 06460 Fax (203) 713-1040 E-mail [email protected]
Questions about this installation can be directed to the INDECO Service Department at: 1-800-5HAMMER (1-800-542-6637)
V COMPACTOR INSTALLATIONCompactor Installation Record
34Compactor Manual
VI COMPACTOR OPERATION
INITIAL OPERATION 1) Start Machine and run at low idle.
2) All bystanders must be clear of machine and compactor.
3) Raise the compactor off the ground with the carrier. Rotate the compactor with the bucket control to assure that the hydraulic hoses will not be pinched or restricted. Swing the backhoe, stretch and curl the boom and stick to check for hose problems.
4) Return compactor to horizontal position and place compactor firmly on the ground.
5) Activate control valve on machine for compactor circuit.
6) Test run compactor at low RPM to purge air from the hydraulic system, gradually increase the machine RPM until compactor is fully powered
7) Observe Compactor performance and inspect for any oil leaks.
8) When temperature is below freezing (32°F), the compactor should be operated at an idle until the hydraulic oil comes up to temperature.
NOTE: THE COMPACTOR ROTATES IN TWO DIRECTIONS. THE COMPACTOR MUST BE BROUGHT TO A FULL STOP BEFORE REVERSING DIRECTION. IF THE DIRECTION IS REVERSED BEFORE IT COMES TO A FULL STOP, DAMAGE CAN BE CAUSED TO THE INTERNAL COMPONENTS.
NORMAL OPERATION
1) Normal compaction technique is to turn the compactor on and place it on the material to be compacted. Apply boom down pressure deflecting the rubber isolators about half way. The compactor is then slowly passed over the material to be compacted while continuing to apply down pressure.
2) The compactor is very effective in compacting granular materials It will produce excellent results depending on the makeup of the material being compacted and the moisture content of the material. Lifts will vary dependent on these factors.
3) It is necessary to turn the compactor off when it is sitting idle and being transported.
357/9/2014
VI COMPACTOR MAINTENANCE
DAILY
Check mounting bracket for loose, cracked or missing bolts. Examine hydraulic hoses for leaking of chaffing. Visually inspect compactor for housing damage. Check hydraulic hose quick couplers for full engagement. Check return line connection. If it becomes restricted, (pinched), motor failure could result.
Weekly
Check fasteners for tightness. Replacement fasteners should be the same type and grade as originals. Inspect rubber isolators for condition. Check oil level within compactor reservoir. To check oil level, remove 3/8” NPT plug from the side of the oil reservoir on the base plate assembly. Operating oil level should be flush with the bottom of the plug hole.
500 Hours of operation
Verify carrier hydraulic flow and pressure.
36Compactor Manual
VII COMPACTOR ECCENTRIC ASSEMBLY PROCEDURE
1) Install Snap-ring side of Eccentric (A) into motor-side Bearing (D).
2) Install Snap-ring (F) onto Eccentric shaft (A).
3) Install motor-side Bearing (D) into motor-side Bearing retainer (B).
4) Install Eccentric (A), Bearing (D) and Retainer (B) into motor-side of Housing (J).
5) Install Adjustment-side Bearing (E) onto Eccentric shaft (A).
6) Install Adjustment-side Bearing retainer (C) onto Adjustment-side Bearing (E) and into Housing (J).
7) Install two adjustment bolts (G) without washers into Adjustment-side Bearing retainer (C) and tighten until bolts stop turning and there is no longer a gap at point (I). Do not use an air gun!
8) At this point measure the distance (K) between the head of the Adjustment bolts (G) and the Adjustment-side Bearing retainer (C).
9) Remove Adjustment bolts (G) and install Washers (H) onto bolts so that the thickness of the Washers is slightly greater than the measured gap in step 8.
10) Install motor.
377/9/2014
VIII COMPACTOR ECCENTRICCROSS SECTION