Package-3
Item Description Unit Quantity Rate (Rs.) Amount (Rs.)
101 Clearing & Grubbing SM 2,500.00
104 Compaction of Natural Ground SM 2,500.00
106a Excavation of Unsuitable Common Material CM 50.00
108aFormation of Embankment from road way
Excavation in common materialCM 142.00
108cFormation of Embankment from Borrow
Excavation in common materialCM 300.00
109a Sub-grade preparation in earth cut SM 3,300.00
Bill No-01: EARTH WORKS
TOTAL (Rs.)
CONSTRUCTION OF TOLL PLAZA ON SEHWAN - RATODERO ROAD (N-55)
AT KM-252BILL OF QUANTITIES
Package-3
Item Description Unit Quantity RATE (Rs.) Amount
(Rs.)
201 Grainular Sub base CM 1,785.00
202 Aggregate Base Course CM 1,161.00
203a Asphaltic Base course Class-A CM 700.00
209a Breaking of existing Road pavement CM 1,770.00
TOTAL (Rs.)
CONSTRUCTION OF TOLL PLAZA ON SEHWAN - RATODERO ROAD (N-55)
AT KM-252
BILL OF QUANTITIES
Bill No-02: SUB BASE & BASE COURSE
Package-3
Item Description Unit Quantity Rate (Rs.) Amount (Rs.)
302aCut-Back Asphaltic for Bituminious
Prime coatSM 3,615.00
303aCut-Back Asphaltic for Bituminious Tack
coatSM 3,500.00
304 b Double SurfaceTreatmentin Shoulder SM 1,733.00
305bAsphaltic Concrete Wearing Course
Class-BCM 173.00
TOTAL (Rs.)
CONSTRUCTION OF TOLL PLAZA ON SEHWAN - RATODERO ROAD (N-55)
AT KM-252
BILL OF QUANTITIES
Bill No .03: SURFACE COURSE & PAVEMENT
Package-3
Item Description Unit Quantity RATE (Rs.) Amount (Rs.)
107a Structural Excavation CM 50.00
107d Grainular Back fill CM 70.00
107e Common Back fill CM 150.00
401a1iiConcrete class-A1 (on ground) for rigid
pavement and barrier.CM 1,320.00
401bConcrete Class-B for drain & protection
workCM 6.00
401f Lean Concrete CM 625.00
404aReinforcement as per AASHTO M-31 Grade-
40Ton 2.00
404bReinforcement as per AASHTO M-31 Grade-
60Ton 14.00
410 Brickwork for manhole crash barrier etc CM 33.00
TOTAL (Rs.)
CONSTRUCTION OF TOLL PLAZA ON SEHWAN - RATODERO ROAD (N-55)
AT KM-252
BILL OF QUANTITIES
Bill No .04: RIGID PAVEMENT & DRAIN
Package-3
Item Description Unit Quantity RATE (Rs.) Amount (Rs.)
601diPrecast Reinforce Concrete Kerb new jersey
barrier for median (double face)M 100.00
SP-601diPrecast Reinforce Concrete Kerb new jersey
barrier for median (one face)M 107.00
601diiPrecast Kerb in Concrete Class-A1 of size
450x150mm including concrete bedding &
hauching.
M 967.00
604a Metal Guard Rail M 145.00
604d Steel Post of Metal Guard Rail M 55.00
607a Traffic Road Sign Category 1 Each 4.00
607b Traffic Road Sign Category 2 Each 4.00
607c Traffic Road Sign Category 3(a) Each 4.00
607e Traffic Road Sign Category 3(c) sm 10.00
608h1Pavement Marking in reflectorized CR Paint
150mmM 1,250.00
609cReflecting Pavement studs raised profile type
single sidedEach 900.00
NSI-1Providing and placing of RCC pipe 228mm dia
for drainage complete with all respect as per
drawings.
M 240.00
NSI-2Apply 03 coats plastic emulsion paint as
specified.SM 2,700.00
NSI-3Providing and placing plastic Drums with
sand in position as per drawings.Each 465.00
NSI-4Providing and placing soft wooden blocks
(0.3x0.3x0.3m) in position.Each 151.00
NSI-5Providing and placing polythene sheet under
rigid pavement.SM 4,183.00
NSI-6Providing and placing 60mm thick tuff tiles
paving or equal for foothpath and parking
area near building.
SM 500.00
NSI-7
providing all the material as per Drawings &
specifications and making of expension joints
as instruction of engineer in-charge.
M 320.00
NSI-8
providing all the material as per Drawings &
specifications and making of construction
joints all as instruction of engineer in-
charge.
M 300.00
TOTAL (Rs.)
CONSTRUCTION OF TOLL PLAZA ON SEHWAN - RATODERO ROAD (N-55)
AT KM-252
BILL OF QUANTITIES
Bill No .05: ANICILLARY WORKS
Package-3
Item # Description Unit Quantity RATE (Rs.) Amount (Rs.)
Excavation 1n foundation, including dressing, leveling, 95%
compaction (AASHTO Modififed) and disposal of
unuitable/Surplus Material
i) In Common Material consisting of aeolion, alluvial. residual
material consisting of gravel, shale volcanic ashes, loam,
sand, clay or any combination of these material, altered or
weather material and boulders less than one quarter (1/4)
cubic meter in volume, embedded in other material.
Cu m 487.50
ii) In Hard Rock which includes firm and rigid igneous,
metamorphic and sedimentary rock. Hard rock constitute firm
and continuous bed rock requiring blasting for excaation. This
will include boulders larger than one quarter (1/4) cubic meter in
volume, provided these are firm and Stable lying in the
continuous bed and constitute more than 50% by volume
compared to other type of material.
Cu m 48.75
iii) In Medium Rock which includes firm and rigid igneous,
metamorphic and sedimentary rock. Medium rock, which can be
removed by Ripper attached to a Bulldozer (200 HP) and chiseling.Cu m 48.75
iv) In Soft Rock which includes firm and rigid igneous,
metamorphic and sedimentary rock, Soft rock, which can be
removed by manual Chiseling.
Cu m 24.38
v) Earth filling, backfilling in plinth, Columns footings, wall footings
and any other foundations.
v(a). With selected excavated material where available with 95%
(AASHTO) compaction (modified proctor) including moistening to
optimum moisture content with mechanical means in 6" layers
from the natural ground level/excavated level to bottom of Stone
Soling (provided separately).
Cu m 100.00
v(b).With selected quarry/Borrow Common (A-4) material
obtained from outside source with 95% (AASHTO) compaction
(modified proctor) including moistening to optimum moisture
content with mechanical means in 6" layers from the natural
ground level/excavated level upto 6" below Stone Soling
(provided for separately).
Cu m 35.00
v(c)With selected quarry/Borrow Granular (A-3) material obtained
from outside source with 95% (AASHTO) compaction (modified
proctor) including moistening to optimum moisture content with
mechanical means in 1 layer of 6" under stone soling (provided
for separately).
Cu m 35.40
v(d) With selected quarry/Borrow Structural fill material obtained
from outside source with 95% (AASHTO) compaction (modified
proctor) including moistening to optitnum moisture Content
with methanical means in 6" layers from the natural ground
level / Ecavated level upto 6" below Stone Soling (provided for
separately).
Cu m 431.00
2
Providing, applying Termite Control Treatment .(Fipronil (Agenda
25EC)} under foundations and floors as per the requirements of
specifications and furnish guarantee that the buildings shall be
free from termites, wood bores and other pests, which cause
damage to wood and other organic material, for a period of 10
years from the date of completion of buildings.
Sq m 177.00
Bill No. 06A - CIVIL WORKS
CONSTRUCTION OF TOLL PLAZA ON SEHWAN - RATODERO ROAD (N-55)
AT KM-252
BILL OF QUANTITIES
1
3
Lean Concrete (1:4:8) Class 'E' Cyllndrical Compressive
Strength f'c=1400 psi
i. Under FootingCu m 217.74
Concrete (1:2:4) Class 'C' Cylindrical Compressive Strength f'c=
3000 psi excluding steel and its bending but including shuttering
centering and its binding as per drawing and specifications and
as directed by Project Manager.
i. Footing Cu m 73.12
ii. Column Cu m 45.41
v. Coping Concrete 3" thick over Parapet Wall as shown in
drawing.Cu m 20.47
vi: RCC Roof Beams Cu m 33.97
vii: RCC Roof Slab Cu m 63.20
viii. RCC Iintel/Sill beam, Jamb column in doors /windows, Pea
rock Concrete Grout (f'c= 3000 psi) in external walls of the
building
Cu m 67.94
ix. RCC stairs Cu m 9.23
Providing Reinforcement Steel (Grade-60) including cutting,
bending.
Placing and binding wire.
i. Footing
ii. Column
iii. Plinth beam
iv. Brick Masonry
vi. Roof Beam
viii. Roof Slab
ix. Mumty Slab
x. RCC lintel/Sill beam/Jamb columns
ix. RCC Stairs
6a
Bitumen coating 2 coats of Bitumen 0.41b/ft2 (0.21b/ft2 per coat
of 40/60 grade) all build surface of foundations, Plinth beam sides
exposed to earth, top suface of Plinth beam and Column exposed
to earth fill in approved manner and as directed by Project
Manager.
Sq m 450.00
6b
Providing and lying 1-1/2" Class C cast in Situ using Find sand
mixed with any approved water proofing agent Sq m 100.00
Stone Soling
Providing, Laying, compacting and blocking 4" thick 'Stone soling
With 2" down gauge graded Stone Blast with Stone dust filling and
fine sand aggregates Over prelaid and precompacted fill, backfill
as per specification. (provided for separately).
i. Under Floors Cu m 45.87
8
i) Vapour Barrier
Providing and Laying of Polythene Sheet 500 gauge (0.005")
thick prime quality laid over stone soling for Flooring Plinth
Protection and ramp as per Specification and as Approved by the
Engineer.
Sq m 483.87
First Class burnt brick masonry Work with cement sand mortar i/c
curlng etc comp1ete in aII respect
i) 9" thick Wall with 1:4 cement sand mortar with deep stuck
Pointing (Ironed Joint by using 10mm round bar to create half
grout neck) both horizontally and vertically only on outer wall
surface of the building as per drawing and as approvd by the
Project Manager
Cu m 128.56
ii). 9" thick Wall with 1:4 cement sand mortar in ordinary finishCu m 13.50
iii). 4.5" thick Wall with 1;4 cement sand mortar in ordinary
finish.Cu m 15.43
4
7
9
5
Tons 28.20
Plaster, 1/2 inch thick on Walls Columns Ceiling inclluidig floating
coat unde plaster.
i. On internal and External walls/columns with 1:4 cement sand
morterSq m 527.43
ii. On Ceiling/Column with 1:3 cement sand mortar Sq m 463.21
iii. Providing applying Aluminium Wire Mesh under Plaster
including
Corner Beads.
Sq m 55.00
Painting:
i) Internal (plastic emulsion paint) 3 coats from reputed
manufacturer as per spcification in approved mannerSq m 527.43
ii) Internal (Enamel paint) 3 coats from reputed manufacturer as
per spcification in approved mannerSq m 79.50
iii) External (eeather shield paint) 3 coats from reputed
manufacturer as per spcification in approved mannerSq m 272.88
Celling Work
i. P/F Plaster of Paris concrete/gola (4"x5") as per specifications
including nailing/screwing as aproved by the Engineer. Mtr 27.72
Floor Ffriishing
i. Providlng and laying of prime quality 8-9mm thick 16 "x 16'' full
body Porcelien Tiles for flooring over 3/4' thick i:2 .Cement
sand morter bed with approved Porcelain Bonding materiaI and
floating coat of cement and as per speifications and approved
by the Project Manager.
a . 16" x.16' Pre- Polished
Sq m 401.71
ii. Providing and laying of prime quality, local, make, 5mm thick or
more glazed ceramic tiles for Bathroom Flooring as per
speifications and as approved by the Engineer.Sq m 35.00
iii. Providing and fixing of prime quality pakistani,3/4"thick pre-
polished Travera/Botesena or equivalent Marble Slab 24" Wide x
4' long over bed of 3/4" thick 1:2 Cement sand mortar with
floatirig coat of cement including making ground edge (bull nose)
to marble, grinding, polishing, filling the joint complete in all
respect as shown in drawing and as approved by the Engineer.
Sq m 4.50
Skirting
i. Porcelain tiles for skirtirig:
Providing and layig 8-9mm thick Pre polished 5"-6" wide"x 16"
long Porcelain tile for skirting as shawn in drawing with
approved quality tile bonding material as per specifications and
as approved by the Project Manager.
Sq m 26.37
ii. Marble tiles for skirting:
Providing and laying of prime quality 1/2" thick 6"x12" Pre
Polished Marble tile (Pakistan parlino or equvalent) for skirting
with 1:2 cement sand mortar as shown in drawings in
approved manner as per specifications i/c finishing etc.
complete in all respects and as approved by the Engineer.
Sq m 1.65
15
Ceramic tile for dado(bathroom walls):
Approved prime quality, local make, 5mm thick or higher ceramic
tiles for
dado or skirting as shown in drawing as per specifications and
as approved by the Engineer.
Sq m 47.50
12
13
14
10
11
16
Roofing
P / L roofing comprising of single layer of tiles 9"x4 1/2"x1 1/2"
(225 x113x40 mm) grouted in 1:3 cement sand mortar with water
proofing agent laid over 1"mud plaster without Bhoosa, over 3" to
2" earth, over polythyne ,over 1" high density thermopore (Poly
Urethene) sheet (tongue and grove),over polythyene over 2
coats of hot bitumen priming coat over RCC Slab complete in all
respect as shown in drawing and as approved by the Project
Manager.
Sq m 453.08
17
Doors Frame:
Vi) Providing and fixing of 1-1/2" thick single leaf Wooden
solid pannaled/patrened door having Deodar wooden framing
1 1/8" thick with 6" Wide top rail, 6" wide middle rail and 9" wide
bottom rail with 5mm thick pressed teak ply With
impression/design on both side i/c 1-1/2 x 3/8" deodar wood
lipping all around the shutter ,with 9" botom rail ,8 " wide lock rail
& 6" Wide top rail i/c brass hinges (4 Nos.), all fitting. french
polish 3 coats and door handles, imported handle lock and
tower bolt etc. complete in all respect as shown in dawing as
approved by the Project Manager.
Sq m 72.00
Windows
Providing and fixing of glazed AIuminum Windows of anodised
bronze (15 micron) colour partly fixed and partly sliding using
deluxe sections having frame size of 100mm x20mm (4"x3/4") and
leaf frame sections of 50mm x 20mm (2"x3/4"), all of 16mm
thickness including 5mm thick imported reflected glass with
rubber gasket using approved standard latches, . hardware, etc as
shown in drawing and as Approved by the Engineer
ii. 2Panel Mercury glass with matel insect screen with aluminium
frame.Sq m 33.26
19
Ventilators Providing and fixing
Aliminium Ventilator of top huged anodized (15 micron) bronze
having frame size 100mm wide x 20mm high x 1.6mm thick
sections including 5mm thick imported solar reflective tinted glass
with rubber gasket using approved standard latches, hardware etc
as shown in drawing and as Approved by the Engineer.
Sq m 9.00
20
Security Grill Providing and fixing of Security Grillin window
including 1/2"x1" steel tube frame having 1/8" wall thickness
anchored to walls with 1/4" dia concrete anchors 1/2"x1/2"steel
bars vertical and horizental weided to steel tube frame as shown
on drawing i/c painting 3 coats complete in all respect and as
approved by the Project Manager.
Sq m 33.26
Carpentry in Kitchen Provinding and fixing in position Kitchen
Wooden Cabinets Consisting of 1-1/2"x1-1/2"thick Deodar wood
frame with 3/4" thick both sides laminated Vinboard boxing
selves,shutters with best quality fittings, all
hardware,nails,handles, hinges, complete in all respects as per
design and drawing and as approved by the Engineer
i- Wall Mount Cabinets Sq m 15.92
ii- Under Counter Cabinets Sq m 6.89
iii(c)- Providing and laying of 1" thick Marble slab on Kitchen
Counter as Shown in DrawingSq m 5.00
18
21
i) Providing and fixing of Collapsible Security Gate (Scissor Type)
made of 2"x3/8" steel bar at top vertical steel channal
3/4"x1/2"x1/2"x1/8" at 4" c/c (approximately) steel flat crosses
5/8" with best quality roller at top of 1-1/2" diameter run on top
steel bar and 1-1/2"x1-1/2"x3/16"angle at each side anchored to
substrate including three hold fast per side steel pins and spacers
,12"long handle,locking arrangment inside and out side, 3 coats of
painting of black japan cnemeled, complete in all respects as
shown in drawing and approved by Project Manager.
Sq m 19.20
ii) Providing and fixing of Hinged Security Gate Consist of1-1/2"x1-
1/2"1/8" steel bar at top, middle and bottom, vertical steel flat 1-
1/2"x1/4" at 3" c/c (approximately) steel flat crosses 1-
1/2"x1/4"including three hold fast per side 12' long handle,
locking arrangement inside and out side, 3 coats of painting of
black japan cnemeled, complete in all respects as shown in
drawing and approved by Project Manager.
Sq m 39.35
TOTAL (Rs.)
22
Package-3
Item # Description Unit Quantity RATE (Rs.) Amount (Rs.)
1
Water Closet , English, prime quality, in vitreous china clay,
Large size with Porcelain P-trap, plastic body low level 12,
liters flushing cistern, Ball type non corrosive siphon valve,
flush handle , PVC drain pipe all in prime quality local make
as approved by the Project Manager
Nos 3.00
2
Water Closet , Pakistan Orissa, prime quality, in
vitreous china clay, Large size with Porcelain P-trap,
plastic body low level 12, liters flushing clstern, Ball
type non corrosive siphon valve, flush handle , PVC
drain pipe all in prime quality local make as approved
by the Project Manager
Nos 6.00
UPVC Pipe for waste and sewage Internal drainage
including Vents with cap, properly laid jointed
Including branches bends, Ys, tees, fitting, clamps,
specials, cutting in floors, walls and making good,
extra painting ion pipe to match the color of the
building testing, complete in all respect.
110mm Pipe Mtr 95.00
73 mm Pipe Mtr 20.00
Provideing, laying, cutting, jointing, testing and
dislnfecting PPRC pipeline in trenches/walls, with
socket joints, all pipe specials using PPRC Pipe of DIN
8077 & 8078 rating PN 20 complete in all respects,
with specials and valves
50mm pipe Mtr 25.00
40mm Pipe Mtr 80.00
25mm Pipe Mtr 90.00
Providing, laying, cutting, jointing, testing and
disinfecting PPRC pipeline in trenches, with socket
joints, using G.l. Pipe of B.S.S. 1387-1967 complete
in all respects, with specials and valves (Medium
Quality)
25mm Pipe Mtr 35.00
5
Gully trap with RCC cover, Cement Concrete chamber
size 6''x 8''x6'' deep in smooth finish Inside & outside,
with 3’’ cast Icon P trapNos 4.00
Providing and Fixing Wash hand basin with pedestal in
approve color prime quality including angle iron bracket set
waste pipe, waste coupling complete in all respects as
Approved by the Engineer Accessories for Wash Hand Basin
are:
Nos 10.00
i. Water Mixer of Faucet for basin/sink complete in all
respectNos 11.00
ii. Connecting Pipe Nos 22.00
7
Providing and fixing of best, quality imported Looking Glass
5mm thick including cost of fitting as Approved by the
Engineer
Sq m 6.75
CONSTRUCTION OF TOLL PLAZA ON SEHWAN - RATODERO ROAD (N-55)
AT KM-252
Bill No. 06B - PLUMBING WORKS
BILL OF QUANTITIES
3
4
6
Providing and Fixing of Approved prime Quality plastic body
Bath Room Accessories Including cast of fitting as
Approved by the Engineer including follow:
i. Towel Rail Nos 5.00
ii. Soap Dish Nos 5.00
iii. Tissue Paper Holder Nos 9.00
9
Providing and Fixing PVT floor trap 4''x3'' with concrete
chamber all around and 4'' PVT grating complete in all
respects as Approved by the Project ManagerNos 17.00
Providing and Fixing brass valves with wheel/handle,
threaded ends all in premium quality local make in internal
as follows:
50mm dia Nos 2.00
40mm dia Nos 2.00
25mm dia Nos 2.00
Providing and fixing of good quality non return valve with
male and female ends
50mm dia Nos 2.00
12
Providing and fixing of plastic body prime quality Muslim
Shower including PVT flexible pipe and CP/Powder coated
Double Bib Cock as Approved by the EngineerNos 9.00
13
Providing and fixing of good quality CP/Powder Coated 1/2''
Double Bib Cock as Approved prime quality as Approved by
the Engineer
Nos 9.00
14Providing and fixing 1/2'' dia CP/Powder Coated prime
quality as Approved by the EngineerNos 22.00
15
Providing and fixing of steel body prime quality showers
Roes including detachable lid pipe as Approved by the
Engineer
Nos 3.00
16
Providing and Fixing approved quality stainless steel sink
33'' x 18'' Pak made complete with angle iron brackets fix
into walls ,1/2'' chromium plated sink faucet , 1-1/4''
chromium plated brass waste coupling, unions and PVT
drain pipe, complete in all respect and Approved by the
Engineer
Nos 1.00
17
Providing and Fixing of prime quality Gas Burn with Triple
Burner stainless steel body with all fixture, PVC gas piping
work upto specified location in kitchen, complete in all
respect and as Approved by the Engineer
Nos 1.00
18
Providing and Fixing of 110mm Dia PVC Class-D Rain Water
Down pipe with shoe , bends in Ducts including clamps, hold
fast as required with the provision of clean out, complete in
all respect and Approved by the Engineer
Mtr 30.00
19
Providing and fixing of foot drain including making gutter
and perforated drain covet as shown on drawing Nos 6.00
8
10
11
TOTAL (Rs.)
Package-3
Item # Description Unit Quantity RATE (Rs.) Amount (Rs.)
16030t Supply and wiring for light & fand with 3x1.5mm sq single core, PVC
insulated stranded copper conductor wire in 20mm (3/4") dia PVC
conduit recessed in the wall of column, roof etcirequired complete in
all respects as approved by the Engineer (Beta Polo Conduit /
Pakistan, New Age, Fast Cable)
Point 67.00
16030s Supply and wiring for circuit with 2x2.5mm sq, PVC insulated
300/500 voltage grade single core stranded copper conductor wire
directly from DB in 20mm (3/4") dia PVC donduit including 1x1.5mm
sq cable as ECC recessed in the wall column and roof atc as required
complete all in respects as Approved by the Engineer, (Beta Polo
Conduit / Pakistan, New Age, Fast Cable)
Point 14.00
16030x Supply and wiring for light sockets with 2x2.5mm sq + 1x1.5mm sq
PVC, insulated 300/500 voltage grade single core stranded copper
conductor wire directly from DB in 25mm (1") dia PVC donduit
recessed in the wall column and roof atc as required complete all in
respects (Beta Polo Conduit / Pakistan, New Age, Fast Cable)
Point 16.00
16030y Supply and wiring for power sockets with 2x4mm sq + 1x2.5mm sq
PVC, insulated 300/500 voltage grade single core copper conductor
wire directly from DB in 25mm (1") dia PVC donduit recessed in the
wall column and roof atc as required complete all in respects (Beta
Polo Conduit / Pakistan, New Age, Fast Cable)
Point 14.00
16030x Supply and wiring for switch sockets to sockets with 2x2.5mm sq +
1x1.5mm sq PVC, insulated 300/500 voltage grade single core
stranded copper conductor wire directly from DB in 20mm (3/4") dia
PVC donduit recessed in the wall column and roof atc as required
complete all in respects.
Point 26.00
16030z Supply and wiring for Ari conditioning power soecket of 1x2.5mm sq
PVC, insulated 300/500 voltage grade single core stranded copper
conductor wire directly from DB in 25mm (1") dia PVC donduit
recessed in the wall column and roof atc as required complete all in
respects as approved by Engineer. (Beta Polo Conduit / Pakistan,
New Age, Fast Cable).
Point 8.00
Supply and wiring of 4 core PVC / PVC / CU, calbe of 600/1000 V
graded in all kinds of existing or given prelaid, pvc conduit in
approved manner as shown in drawing complete in all respects, as
approved by the Engineer.
i) 4 Core 120mm² PVC / PVC / CU cable Mtr 53.34
ii) 4 Core 35mm² PVC / PVC / CU cable Mtr 71.62
Iii) 4 Core 25mm² PVC / PVC / CU cable Mtr 114.29
iv) 4 Core 16mm² PVC / PVC / CU cable Mtr 109.11
v) 4 Core 10mm² PVC / PVC / CU cable Mtr 45.11
Supply and wiring of single core PVC cable 450/750 Volts grade in
prelaid pvc conduit as ECC with power calbe in approved manner as
shown in drawing complete in all respects, as approved by the
Engineer. (Pakistan, New Age, Fast)
i) 1x6mm sq Mtr 137.15
ii) 1x4mm sq Mtr 106.37
CONSTRUCTION OF TOLL PLAZA ON SEHWAN - RATODERO ROAD (N-55)
Bill No. 06 C - ELECTRICAL WORKS
AT KM-252
BILL OF QUANTITIES
The rate for all BOQ item shall include providing, construting, fabricating, fixing, executing, applying, as applicable and additionally as otherwise stated against the
specific items shall include all materials, labor, efforts, plant and equipment, complete in all respects, as per drawings, approved shop drawings, specifications, as
per NEC, NFPA 70 & NEMA, various applicable stipulations, miscellaneous details, as per instruction and as directed by the Engineer. All sampels shall be procured
and provided by the contractor at his own cost for approval by the Engineer.
16030d
16030d
iii) 1x2.5mm sq Mtr 109.11
Providing and laying PVC conduit conforming to BS-6099 and BS-
3506 including excuation back filling, pull boxes, spection boxes,
tees, bends, crosses, using accessoties for proper sealing joints, in
roof slabs, walls and under floors for power calbes including cutting
in wall and floors as required, back filling and making good the cut
cavities with cement sand mortar all in approved manner as shown
or drawings, complete in all respect as approved by the Engineer
(Beta Polo)
i) 100mm dia Mtr 45.72
ii) 50mm dia Mtr 104.24
iii) 40mm dia Mtr 257.54
iv) 25mm dia Mtr 99.06
Supply, installation and connecting of gang, switches one or two way
with plastic back box including wall cutting, fixing etc, and making
good complete in all respect as approved by the Engineer (Clipsal,
Legrand)
ii) 2 gang 1 way light controll switch Each 6.00
iii) 3 gang 1 way light controll switch Each 5.00
iv) 4 gang 1 way light controll switch Each 8.00
v) 5 gang 1 way light controll switch Each 4.00
vi) 6 gang 1 way light controll switch Each 14.00
16020h Supply, installation, connecting and testing prime quality fan dimmer
with switch with plastic /pvc back box complete in all respects as
approved by the engineer (Clipsal, Legrand) Nos 21.00
16020c Supply, installation and fixing 13, Amps provcarbonate flame
retardant 3 pin, Mulitpurpose swithch, socket unit with fancy gang
plate fixed on die fabricated power coated metal board recessed in
wall or comumn including connectinos as required (Vivace intl socket
Clipsal make), complete in all respects
Nos 43.00
16020c Supply, installation and fixing 15, Amps provcarbonate flame
retardant 3 pin, swithch, socket unit with fancy gang plate fixed on
die fabricated power coated metal board recessed in wall or comumn
including connectinos as required (Vivace intl socket Clipsal make),
complete in all respects
Nos 21.00
16050c Supply, installation, connecting and testing of fluorescent tube light
fitting fixture, 4' length with frame diffuser, electronic ballast ande
28 watts fluorescent TLS tube rod cool day light lamp as Phlips TMS
215 Slimline complete in all respects as Approvec by the Engineer,
(Philips pierlite, Osram)
Nos 16.00
16050c Supply, installation, connecting and testing of fluorescent tube light
fitting fixture, 4' length, complete with frame diffuser, electronic
ballast ande 2x8 watts fluorescent TLS tube rod cool day light lamp as
Phlips TMS 225 Slimline complete in all respects as Approvec by the
Engineer, (Philips pierlite, Osram)
Nos 6.00
16050c Supply, installation, connecting and testing of 2'x2' fluorescent tube
light fitting fixture, complete with electronic ballast ande 4x18 watts
fluorescent TLS tube rod cool day light complete in all respects as
Approvec by the Engineer.
Nos 8.00
16050e Supply, installation, connecting and testing of 1x23 W recessed typy
Energy Saver Down Light with Bakelite lamp holder reflector
(Imported) fitting complete with 1x23 watts CFL lamp as per Philips
Cat, No. FBH 145/1x18 W PLC, complete in all respects as required as
Approvec by the Engineer.
Nos 44.00
16050d Supply, installation, connecting and testing of 1x23 W head lamp
holder, reflector (Imported) fitting complete with 1x23 watts CFL
lamp complete in all respects as required as Approvec by the
Engineer. (Philips, Plerite, Osram)
Nos 12.00
16040b
16020b
16030d
16050d Supply, installation, connecting and testing of water proof light IP54
complete with electronic ballast, splash profcasing and 1x36 watts
flurescent tube rod complete in all respects as required as Approvec
by the Engineer. (Philips, Plerite, Osram)
Nos 9.00
16060e Supply, installation, connecting and testing of 56' sweep ceiling fand
with ceiling rose ceiling hook, fan box, matching GI pipe for suitable
hight wiring upto termination point complete in all respects as
Approvec by the Engineer. (GFC, Climax, Royal)
Nos 13.00
Supply, installation, connecting and testing of electric exhaust fan
including metal, louvers, ON / OFF swithc, calbe, complete in all
respects as Approvec by the Engineer. (GFC, Climax, Royal)
iii) 12" Metal Body Nos 9.00
iv) 18" Metal Body Nos 1.00
16060d Supply, installation, connecting and testing of 450m (18") sweep wall
bracket fan with blades, housing regualtor & pulling cord switch
fitted on wall or column with GI clip ncluding connection as required
complete in all respect as approved by the Engineer.
Nos 9.00
16110 Tubewell
Providing and construction of Tube Wll with dia boring installed with
S" dia SM 14 guage blind pipe, steel strainer. The space between
boring wall and MS pipe sahll be filled with coarse sand 1/8" min and
3/8" max in size. The tube well shall be installed with 4" dia 1.5 K.W
submercible pump 1" dia GI / HDPE pipe (PE.63) suction pipe as pe
rrequirement with respect to ground water, table Electricl Fanel
including Circuit breaker, U/OVT relay and plugs PF improvement
panel, Soecket RCC pump shade / cover complete in all respect and
as per the approval of the Engineer. The length of stainer will
depend upon the ground water table and water bearing starta with a
minmum 50 ft length. Submercible pump is suppored by 8mm steel
insulated wire power cable shall be wraped water proof tape as
shown in drawing SB GOLDEN PUMPS)
Mtr 38.10
16110 Providing , fixing, connecting and testing of (as per manufacturer
recommendations) AC single phase pumping set 2HP rating 220
volts, 50 cycles electric motor with centrifugal pump compatible with
motor suction and discharge 1" x 1" coupled on a comport base plat.
Foundaton bolts 1" dia GI piping connections and required bends,
sockets tees, unions etc, gate valve, check valve non-return valve
foot valve and strainer at UGT sump level a per drawing, Electrical
Panel including Ciruit bradker, U / OVT relay and plulgs, sockets PF
improvement panel RCC pump shade / cover, complete in all respect
and as approved by the Engineer (KSB, GOLDEN PUMPS)
Job 1.00
Distrubution Boards
16060d
16070 Supply, installation, connecting and testing of Main, panel board
consisting of 14 SWG M.S powder coated indoor floor mounted and
suitable foundation compelte with all internal wiring, tags,
identification labels, TPN&E copper, bus bards, gransparent plastic
sheet armoured glands lockable covers, cable brass glands where
reqired consisting as follows additinally conforming / complying with
details as shown on drawings complete in all respect as approved by
the engineer (ABB, MG GE or Eqv)Incoming
01 No. 200 Amps T.P 35 KVA MCCB ADJUSTABLE circuit breaker (ABB
or equivalent)
03 Nos - Indication Lamp
01 No - Voltage Selector Switch
01 No - Volt meter (Digital) 7 Point
01 No - Current Selector Switch
01 No - Current Meter (Digital ) 5 Point
06 Nos - 2 Amps Fuses
Out Going
01 No. 100 Amps TP RC25KA MCCB
01 No. 16 Amps DP RC 15 KA MCB
01 No - 25 Amps TP RC255KA MCB
01 No - 63 Amps TP RC25KA MCCB
02 No - 30 Amps TP RC25KA MCCB
Suitable Common Copper Bus Bar
Natural and Earth Bus Bars
Nos 1.00
16070 Supply, installation, connecting and testing of distribution board
(Building DB) consisting of 16 SWG M.S Powder coated indoor
recessed tyupe mounting front door access complete with all interval
wiring tags indentification lables, TPN&E copper bus bards
transparent plastic sheet, lockable, covers, cable brass glands where
required consisting as follows additionally conforming / complying
with details as shown on drawings, complete in all respect as
approved by the Engineer (ABB, MG, GE or Fqv)complete in all
respect as approved by the engineer (ABB, MG GE or Eqv)
Incoming
01 No - 100 Amps T.P MCCB 25 K circuit breaker
03 Nos - Indicatio Lamp
01 No - Volt Meter (Digital) 7 Points
01 No - Volt Selector switch
03 Nos - Vuses
Out Going
Nos and ratng S.P of MCB circut breaker
09 Nos - 06 Amps SP MCB RC10KA
07 Nos - 10 Amps SP MCB RC10KA
09 Nos - 16 Amps SP MCB RC10 KA
03 Nos - 20 Amps SP MCB RC10KA
Suitalbe Common Copper Bus Bar
Natureal and Earth connector
Nos 1.00
16070 Supply, installation, connecting and testing of distribution board
(Genset Room) consisting of 16 SWG M.S Powder coated indoor
recessed type mounting front door access complete with all interval
wiring tags indentificatino lables, lockable covers, ccalbe brass glands
where required TPN&E copper bus bards transparent plastic sheet,
consisting as follows additionally conforming / complying with
details as shown on drawings, complete in all respect as approved by
the Engineer (ABB, MG, GE or Fqv)
Incoming
01 No - 20Amps DP MCB 15Ka ciruit breaker
03 Nos - Indication Lamp
01 No - Volt Meter (Digital) 5 Points
01 No - Volt Selector swithc
03 Nos - fuses
Out Going
Nos and ating S.P of MCB circuit breaker
01 Nos - 06 Amps SP MCB RC10 KA
01 No. - 10 Amps SP MCB RC10KA
01 Nos - 16 Amps SP MCB RC10KA
Suitable Common Copper Bus Bar
Natural and Earth connector
Nos 1.00
16070 Supply, installation, connecting and testing of distribution board
(INTERCHANGE FLOOD LIGHT) consisting of 14 SWG M.S Powder
coated indoor recessed type mounted and suitable foundation,
weather proof IP54 including front door access complete with all
internal wiring tags indentification lables, Photo censor and
mounting bracket of Photo sensor for Auto Switching of lights,
nagnetic contracors, Fuses, TPN&E copper bus bards transparent
plastic sheet, lockable covers, cable brass galnds where required
consisting as follows additionally conforming / complying with
details as shown on drawings, complete in all respect as approved by
the Engineer (ABB, MG, GE or Fqv)
Incoming
01 No - 20Amps Three POLE MCCB 15Ka ciruit breaker
03 Nos - Indication Lamp
01 No - Volt Meter (Digital) 7 Points
01 No - Volt Selector switch
03 Nos - fuses
01 No - Photo light sensor for auto light swithces
Out Going
Nos and ating S.P of MCB circuit breaker
01 Nos - Magnetic Contractor 25A
01 No. -
01 Nos - 06 Amps SP MCB RC10KA
Suitable Common Copper Bus Bar
Natural and Earth connector
Nos 1.00
16070 Supply, installation, connecting and testing of distribution board (DB
ROAD LIGHT) consisting of 14 SWG M.S Powder coated indoor
recessed type mounted and suitable foundation, weather proof IP54
including front door access complete with all internal wiring tags
indentification lables, Photo censor and mounting bracket of Photo
sensor for Auto Switching of lights, nagnetic contracors, Fuses,
TPN&E copper bus bards transparent plastic sheet, lockable covers,
cable brass galnds where required consisting as follows additionally
conforming / complying with details as shown on drawings, complete
in all respect as approved by the Engineer (ABB, MG, GE or Fqv)
Incoming
01 No - 30Amps Three POLE MCCB 25Ka ciruit breaker
03 Nos - Indication Lamp
01 No - Volt Meter (Digital) 7 Points
01 No - Volt Selector switch
03 Nos - fuses
01 No - Photo light sensor for auto light swithces
Out Going
Nos and ating S.P of MCB circuit breaker
01 Nos - Magnetic Contractor 25A
Suitable Common Copper Bus Bar
Natural and Earth connector
Nos 1.00
16070 Supply, installation, connecting and testing of distribution board
(CANOPY LIGHTS) consisting of 14 SWG M.S Powder coated indoor
recessed type mounted and suitable foundation, weather proof IP54
including front door access complete with all internal wiring tags
indentification lables, Photo censor and mounting bracket of Photo
sensor for Auto Switching of lights, nagnetic contracors, Fuses,
TPN&E copper bus bards transparent plastic sheet, lockable covers,
cable brass galnds where required consisting as follows additionally
conforming / complying with details as shown on drawings, complete
in all respect as approved by the Engineer (ABB, MG, GE or Fqv)
Incoming
01 No - 50Amps Three POLE MCCB 15Ka ciruit breaker
03 Nos - Indication Lamp
01 No - Volt Meter (Digital) 7 Points
01 No - Volt Selector switch
03 Nos - fuses
01 No - Photo light sensor for auto light swithces
Out Going
Nos and ating S.P of MCB circuit breaker
01 Nos - Magnetic Contractor 50A
05 No
01 Nos. 16 Amps SP MCB RC10KA
0 Nos. 20 Amps SP MCB RC10KA
Suitable Common Copper Bus Bar
Natural and Earth connector
Nos 1.00
16070 Supply, installation, connecting and testing of distribution board
(TOLL BOTH DB) consisting of 14 SWG M.S Powder coated indoor
recessed type mounted and suitable foundation, weather proof IP54
including front door access complete with all internal wiring tags
indentification lables, Photo censor and mounting bracket of Photo
sensor for Auto Switching of lights, nagnetic contracors, Fuses,
TPN&E copper bus bards transparent plastic sheet, lockable covers,
cable brass galnds where required consisting as follows additionally
conforming / complying with details as shown on drawings, complete
in all respect as approved by the Engineer (ABB, MG, GE or Fqv)
Incoming
01 No - 30Amps Three POLE MCCB 15Ka ciruit breaker
03 Nos - Indication Lamp
01 No - Volt Meter (Digital) 7 Points
01 No - Volt Selector switch
03 Nos - fuses
Out Going
Nos and ating S.P of MCB circuit breaker
01 Nos - Magnetic Contractor 50A
05 No
01 Nos. 60 Amps SP MCB RC10KA
02 Nos. 16 Amps SP MCB RC10KA
01 Nos - 20 Amps SP CMB RC10KA
Suitable Common Copper Bus Bar
Natural and Earth connector
Nos 4.00
Grounding Work
16090 Supply, installation connection, boring / excavation and testing to
less than 1 ohm of earthing set with 20mm dia 3 meter long copper
rod encased in 3" dia pvc pipe lowerede and burreed in ground in 4"
dia boring in all type of soil to water table at required depth, plated
connected with 1x70 mm sq HDBC bare cu-conductor from
grounding rod to earth lest copper bar as earth connecting point, the
remaining cavity around the copper rod shall be filled with gournding
enhancement compound packed hard all around the copper rod for
MDB grounding pole light gounding and lighting protection gounding
complee in all respect as approved byt the engineer.
Job 3.00
16090 Supply, installation 12" long 2", wide 1/2" thick (12"x2"x1/2") copper
bus bar as earth connecting point (ECP). The (E.P) shall be complete
with insulator, washers, nuts, bolts, mounting installation and
operational accessories as per technical specificaiton and as per site
requirement complete in all resepct as approved by the engineer.
Job 3.00
16090 Supply, installation and wiring of single core 1x70mm sq PVC copper
wire 600/1000 volts grade in prelaid pvc conduit from ECP to MDB as
ECC conductor in approved manner as shown in drawing complete in
all resepct as approved by the engineer (Pakistan, New Age, Fast
Cable).
Mtr 21.33
16090 Supply and construction of 2ftx2ft and 2ft deep brick Masonry hand
hole to cover earthing GI pipe tee i/c comented door, inside 1:4
plaster and 1ftx1ft RCC cover flush on floor complete in all respect as
Approved by Engineer.
Job 3.00
16090 Supply and installation of 1 1/2" x 1/3" copper strip from top of
building (lighting spike) to ECP earthing point inclading brass saddle
at 1 ft interval, brass screw etc complete complete in all respect as
Approved by Engineer.
Mtr 15.24
16090 Supply and installation on top of building 1" dia meter 3ft long
lighting copper rod with ball and five spikes fix on head complete in
all respect as Approved by Engineer.
Job 1.00
Road pole lighting
16050g Supply and installation of mild steel tubular swaged / welded siliver
enmeled painted road light single arm pole of over all length 10 Mtrs
having 3 steps and dimension of 150x100x75mm & tube thickness
6.5.4mm respectively for fixing road light complete with M.S
baseplate having 20mm thickness and 300sqmm long corved bracket
with 800mm radius for mounting light fixture with all required civil
works (including PCC foundaions wherever required as pe relevant
standards and as per instructions) with suitable precautions for
ensuring prevention of watering ressand proper water proof
termination of calbes and wires complee naneatand satifactory
manner complete in all respect as Approved by the Engineer.
Job 8.00
16050g Supply and installation of mild steel tubular swaged / welded siliver
enmeled painted road light double single arm pole of over all length
10 Mtrs having 3 steps and dimension of 150x100x75mm & tube
thickness 6.5.4mm respectively for fixing road light complete with
M.S baseplate having 20mm thickness and 300sqmm long corved
bracket with 800mm radius for mounting light fixture with all
required civil works (including PCC foundaions wherever required as
pe relevant standards and as per instructions) with suitable
precautions for ensuring prevention of watering ressand proper
water proof termination of calbes and wires complee naneatand
satifactory manner complete in all respect as Approved by the
Engineer.
Job 6.00
16050d Supply, fixing and installation of Road lighting luminaire suitalbe on
pole for use with High Presure Sodium Vapour Philips SGP 338 SON-T
250W lamp including housng cum reflector of deep drawin
aluminum powder coated in grey colour outside and all electricla
accessories such as energy efficient copper ballast electronic ingitor
power factor improvement copacitor etc are pre-wired upto to
terminal block and mounted on a specially desinged detachalbe gear
plate. Conformance to IP 54 protection complete in all respect as
Approved by the Engineer.
Job 20.00
16070 Supply and fixing of function box concelead in foundaton with
lockable cover, dust and wheathe proof gasket
250mmx200mmx150mm deep junction box nominal size of 16 SWG
thick MS sheet cable looping box with the existing pole with MS
clamp made out of 25mmx3mm thick at iron with suitable nuts and
bolts complete with hinged cover and locking screws earth studs
neoperene gasket suitalbe for pole mounted including supply and
fixing one no 6 Amp MCB carrier with base and 4 way + grounding 60
Amp terminal block suitable to receive PVC armoured cable fixed on
suitable size bakelite sheet base complete with connection painting
as required complete in all respect as Approved by the Engineer.
Job 20.00
16040 Supply and fixing of PVC pipe sleeve 40mm dia Nominal 2.5 mtr
length along the pole or protection of underground cable as required
(vertical length) as required, complete in all respect as Approved by
the Engineer. (Polo Beta)
Job 20.00
16030d Supply, laying, installation, glanding and termination of 3 core 2.5
Sqmm PVC insulated copper flexible cable 13meters in length in
tubular pole glands, nuts bolts, required accesssries for providing
supply to the street lights as required as approved by the Engineer
(Pakistan, New Age, Fast Cable)
Job 10.00
16030d Supply, laying , glanding, termination, testing and commissoning of
the flowing sizes of 600/1000V grade PVT insulated and PVT
sheathed armoured copper stranded condulor 4core 16mm.sq power
cable and 6mm.sq coppperd cable as ECC connected to grounding pit
/ ECP in prelaid 40mm cnduit ,complete as required as per specifions
as approved by the Engineer (Pakistan, New Age, Fast Cable)
Mtr 284.97
Toll plaza Canopy & Flood Lighting
16050h Supply & installation of type mild steel tubular swaged/welded Road
lihgt pole of over all length 9M having 3 sreps and dimension of
150x100x175mm & tube thickness 6-5-4mm respectively for fixing
road light complete with MS baseplate having 20mm thickness and
300sqmm long curved bracket with 800mm fadius for mounting
light fixture with all required civil works (Including PCC foundations
wherever required as per relevat standards and as per Instructions)
with suiablw precaution for ensuring prevention of watering ressand
proper water proof-termination of cables and wires completed in all
stalsfactory manner as approved by the Engineer.
Job 6.00
16050d Supply. Fixing and installation of Road lighting luminare suitable
onpole for use with High Pressure Sodlum Vapour Philips Tango 3 T
250W lapm including housing cum reflector of deep drawn
aluminlum, powder coated in grey colour ballas electronic lgnitor,
power factor improvement capacitor etc, are apre wired upto a
terminal block and mounted on a specially designed detachable gear
plate Conformance to P 54 protection complete in all respect as
Approved by the Engineer
Job 10.00
16050d Supply fixing and Installation of toll plaza canopy luminaire
rececessed type Philips MPF-932 400wa-ts HPIT Muli, Ballast & lam
including housing cum reflector and all electrical accessories such as
energy efficient multi ballast, electronic ignitor, power factor
improvement capacitor etc, are p e-wired upto a terminal block and
mounted on a specially designed detachable gear plate Conformance
to IP 54 protection complete in all respect as Approved by The
Engineer
Job 8.00
16050h Supply and fixing of GI Bbraket silver enameled on top the pople for
the installation of the integral flood light luminaire at 9.5 mtr long
pole as rewuired for flood/road lights as required Job 6.00
16070 Supply and fixing of junction box concelaed in foundation with
lockable cover ,dust and wheather proof gasket
250mmx200mmx150mm deep junction box nominal size with SWG
thick MS Sheet cable looping box with the existing pole with MS
clamp made out of 25mmx3mm thick flat iron with suitable nuts and
bolts complete with hinged cover and locking screws earth studs
neoprene gasket suitable to receive PVC armoured cable fixed on
suitable size Baketillte sheet base complete with connection painting
as required, complete in all respect as Approved by The Engineer.
Job 10.00
16040 Supply and fixing of pvc pipe sleeve 40 mm dia Nominal 2.5 mtr
length along the pole or protection of underground cable as
required, Complete in all respect as approved by The Engineer (Polo
,Beta)
Job 10.00
Supply, laying , installation , glanding and termination of 3core2.5
sqmm PVC insulated copper flexible cable 10.5mtres in length in
tubular pole glands, nuts, bolts, required accessories for providing
supply to the street lights as required as approved by the Engineer
(Pakistan, New Age, Fast Cable)
Job 10.00
Supply and wiring of single core PVC cable 450/750 Colts grade in
prelaid40mm pvc conduit for flood lights and canopy recessed light
in approved manner as shown in drawing complete in all respects as
Approved by the Engineer (Pakistan, New Age, Fast)
16030d
i) 1 x 6mm sq Mtr 571.47
ii) 1 x 4mm sq Mtr 197.20
Tranformer
16010 Design, fabrication, manufactering, supply, installation testing and
commissioning of 200KVA , 11KV/415V outdoor power transformer
including all external radiating tubes, oil filling and drainage vales
lifting lugs etc with all installation and operation accessories and
making oil pit and protection relays ,temperature alarm & devices
and separate two grounding systems for neutral and body ground
with 3mtr copper 'Road' CC foundation as per required design must
tomply all the WAPADA standards and required as per site as per
tender specification and as desired by The Engineer
Job 1.00
16100 Design, fabrication, manufactering, supply, installation testing and
commissioning of prime Diesel Generator 100KVA (primary) at 0.8
PF,400voptls, the three phase, 4wire, 50hz at 1500RPM including
AVR along with Electronic Panel and switches, tool Kit, Day fuel tank
500ltrs and essential piping systems and transportation at site and
separate two grounding systems for neutral and body grounding
with 3mtr copper road as Approved by The Engineer of the following
brands (SDMO france, PERKINS , GUMMINS UK, MITSUBISHI Japan,
CAT UK/USA, F.G. WILLSON UK)
Job 1.00
16100 Design, fabrication, manufactering, supply, installation testing and
commissioning of Autoransfer switch panel for Diesel Generator
100KVA Including 75A FOUR POLE MCCB Breaker ,timer relays,
U/OVT relay, Phase failure relay Auto start ,Auto Shutdown system
and transportation at site ,as approved by The Engineer
ABB/MG/SCHCNIDER
Job 1.00
16100 Design, fabrication, manufactering, supply, installation testing and
commissioning of Weather Proof and soundproof Canopy (85dB at
1m) Suitable for the above diesel generator set as approved by The
Engineer
Job 1.00
16100 Construction of RCC foundation with Anti-vibration pad for
replacement of DG set complete in all respect as approved by The
Engineer
Job 1.00
TOTAL (Rs.)
16030d
Package-3
Item # Description Unit Quantity RATE (Rs.) Amount (Rs.) 1 Excavation 1n foundation, for external works
including underground wter tank,manhole,septic
tank,pit,etc disposal of unsuitable/surplus
Material in Common Material consisting of
aelion,residual material consisting of gravel,shale
volcanic ashes,loam,sand,clay or any combination
of these material,altered or weather material and
boulders less than one quarter (1/4) cubic meter
volume emended in other material.
Cu m 120.00
2 v) Earth filling, backfilling with selected
excavated material where available with 95%
(AASHTO) COMPACTION (modified proctor)
includind moistening to optimum moister content
with mechanical means in 6" layers from the
natural ground level/excavated level.in plinth,
Columns footings, wall footings and any other
foundations.
v(a). With selected excavated material where
available with 95% (AASHTO) compaction
(modified proctor) including moistening to
optimum moisture content with mechanical
means in 6" layers from the natural ground
level/excavated level.
Cu m 45.00
3 Lean Concrete (1:4:8) Class 'E' Cyllndrical
Compressive Strength f'c=1500 psi. Cu m 3.00
4 Concrete (1:2:4) Class 'C' Cylindrical Compressive
Strength f'c= 3000 psi excluding steel and its
bending but including shuttering centering and
its binding as per drawing and specifications
and as directed by Project Manager.
Cu m 12.00
5 Concrete (1:1-1/2:3) Class "B" Cylindrical
Compressive Strenth fc=4000 psi(for U/G Water
Tank) excluding steel and its bending but
including shuttering centring and its binding as
per drawing and specifications and as directed by
Project Manager.
Cu m 8.00
6 Concrete (1:1:2) Class "A" Cylindrical Compressive
Strenth fc=4500 psi(for rain water disposal line)
excluding steel and its bending but including
shuttering centring and its binding as per drawing
and specifications and as directed by Project
Manager.
Cu m 60.00
7 Providing Reinforcement Steel (Grade-60)
including cutting bending placing and binding
wire.
Ton 2.00
AT KM-252
BILL OF QUANTITIES
CONSTRUCTION OF TOLL PLAZA ON SEHWAN - RATODERO ROAD (N-55)
Bill No. 06D - EXTERNAL WORKS
8 First Class burnt Brick Masonary work with 1:4
Cement Sand Mortar i/c curing etc complete in all
respect.
Cu m 3.00
9 Fixing and laying of 60mm thick Concrete pavers
including 2" sand bedding over prepared base as
per drawings and specificatoins and as per
Approved by the Engineer.
Sq m 150.00
10 Plaster, 1/2 inch thick 1:3 Cement Sand Plaster on
R.C.C Walls / Ceiling / Slab inclluidig floating coat
unde plaster.
Sq m 50.00
11 Plaster and Sealant Water proofing on inside and
out side of Underground Water Tank by Acrylic
Polymer modified cementitious coating brush
applied trowel finished, three coats,including
10mm white aggregate protection cover layer on
inside and covering slurry plaster outside 2-3mm
of minimum thickness,complete in all respect as
per manufactur's instruction and approved by the
Project Manager.
Sq m 25.00
12 CI Cover for U/G & Over Head Water Tank
Providing and fixing Alass C-250BS EN:124 (70Kg)
CI Cover 18"x18" with T-shape CI frame with fish
tail anchors embedded in slab and locking
arrangment as shown in drawing complete in all
respect as approved by the Engineer.
Nos 2.00
13 R.C.C. Cover for Manhole Providing and fixing
3"(75mm) thick RCC manhole cover ,22" (550mm)
dia, with tee shaped CI frame of 20"(500mm)
clear i/d (frame weighing 40kg) and fish tail
anchors embedded in slab, complete in all respect
as Approved by the Engineer.
Nos 14.00
14 Testing of under ground water storage tank as
per specifications and as directed by Project
Manager.
Nos 1.00
15 Stone Soling
Providing, Laying, compacting and blocking 4"
thick 'Stone soling With 2" down gauge graded
Stone Blast with Stone dust filling and fine sand
aggregates Over prelaid and precompacted fill,
backfill as per specification. (provided for
separately).
Cu m 15.00
Providing and laying R.C.C. pipe, moulded with
cement concrete 1:1-1/2:3 with apigot socket or
collar joint etc including cost of reinforcement
conforming to B.S.S911 Part I:981,Class
"L" including carriage of pipe from factory to site
of work lowering in trenchs to correct alignment
and grade,jointing,cutting pipes where necessary
finshing and testing, etc,complete in all respect as
Approved by the Engineer.
12" dia Pipe Mtr 170.00
16
17 Over-burnt Brick GRAVEL Filling in Soakage pit
Providing,Filling Over burnt brick Gravel Filling in
Soakage pit 3" down gauge graded brick gravel as
per specification complete in all respect as
Approved by the Engineer.
Cu m 14.00
18 Providing and fixing of 3/8"x6" deep continues
ribbed water stopper in UGWT construction joint
as per drawing and specification.Mtr 12.50
TOTAL (Rs.)
Package-3
Item # Description Unit Quantity RATE (Rs.) Amount (Rs.)
7.1 P/F & Steel H Column, 14"x14"(57 Kg/ft) M.S.Ton 2.47
7.3 P/F & I Purlins "C" Section 150mm x 55mm
channels & runners.Ton 0.41
7.4 P/F & I 1/2 dia M.S bar 2"x2"x1/4" M.S angle
plate 3x40mm 3/16" M.S.cleat plate Ton 51.08
7.5 P/F & I M.S base plate 20mm thick (650mm x
650mm size)Ton 3.96
7.6 P & G Master flow 524 (non shrinkage material) &
Gasset plate having 650x650mm foundation. No 1.75
7.7 S & C 20guage C.G.I Sheet including 50mm long
Screws with J Bolts.Sq m 582.75
7.11 S&I Cannopy fascia white acrylic sheet Sq m 99.50
7.14 ii. P/F 2'X2' Matel false celling consisting of
gypsum board panels 10-12 mm with Alumunium
lamination / fail on back side and design on the
front i/c cost of framework of tees angles and
4mm hanging G.I wire, including all wastage and
leveling etc, complete in all respect as approved
by the Project Manager.
LM 582.75
7.15 P & F 24 guage M.S sheet welded with top 16
guage MS Sheet of fascia box.LM 16.97
AT KM-252
BILL OF QUANTITIES
TOTAL (Rs.)
CONSTRUCTION OF TOLL PLAZA ON SEHWAN - RATODERO ROAD (N-55)
Bill No. 06 E - STRUCTURE STEEL CANOPY & RELATED WORKS
Package-3
Item # Description Unit Quantity RATE (Rs.) Amount (Rs.)
NSI-1P/F of Aluminum Composite Panel on outer side of
boothSM 24.00
NSI-2 P/F of 2 ply Fiber glass on inner side of toll booth. SM 25.00
NSI-3P/F of Insulation Thermo pore 25 kg / cum in
between ms sheet and fiber glass in toll booth.SM 22.00
NSI-4 P/F of False Ceiling 0.6x0.6 side of toll booth. SM 4.00
NSI-5P/F of Computer and cash table with Lassani
(16mm) 3/4" thickSM 1.00
NSI-6P/F of Ventilator of Aluminum Sliding shutter with
grill in Toll BoothSM 0.23
NSI-7 P/F of 50mm Sqr. 16 swg Frame Pipe for toll booth M 93.00
NSI-8P/F of 100 mm with 8.0 mm wall thickness steel
pipe frame for Toll Booth Protection.M 50.00
NSI-9 P/F of Tempered Glass 5mm thick in toll booth SM 7.00
NSI-10P/F of 10" dia Exhaust fan along with closers and fly
netting.Each 1.00
NSI-11
P/F of Anchor bolts and nuts 16 mm dia 500 mm
long in concrete foundation for booth protection
pipe.
No 16.00
NSI-12P/F of Rawlplug 12.5 mm th. 150 mm long for booth
protection pipe.No 16.00
NSI-13P/F of steel base plate 250 mm dia 16 mm th. for
booth protection pipe.No 4.00
NSI-14P/F of steel base plate 250x250 mm, 16 mm th. for
booth protection pipe.No 4.00
NSI-15Application of 3 coats Golden yellow, green & brown
colors as per drawing.SM 43.00
NSI-16
P/F of Crest brand LED Slim Panel Lights in False
ceiling (12 Watts of Toll Booth as per approved
drawing.
No 2.00
NSI-17P/F of Door lock of Toll Booth as per approved
drawing.No 1.00
NSI-18
P/F of Complete Wiring with PVC conduit in Booth
for Exhaust fan, two LED Slim lights, and two
sockets, A/C 1.0 ton etc. as per approved drawing.
No 1.00
NSI-19P/F of Circuit breaker as per requirement. as per
approved drawing.No 3.00
CONSTRUCTION OF TOLL PLAZA ON SEHWAN - RATODERO ROAD (N-55)
AT KM-252
BILL OF QUANTITIES
BILL.NO: 6F :STANDARD TOLL BOOTHS
NSI-20
P/F of one three pin socket outlet 15/20 amps point
controlled by one switch wiring complete with pvc
single core cable 4 sq. mm in concealed pvc
conduit including earth wire.Circuit breaker as per
requirement. as per approved drawing.
No 3.00
NSI-21 P/F of Power plug along with accessories. No 1.00
NSI-22
P/I of A/C 1.0 ton ACSON / Mitsubishi or Equal of
MS pipe grill fixed for out door unit complete fitting
with all safety measures and necessary welding
bolts and nuts as required, rubber packing and
other materials. Power plug along with accessories.
No 1.00
NSI-23
P/I circuit wiring from DB to Switch board, wiring
with PVC single core cable 2.5 sq. mm +1.5 mm as
ECC in PVC conduit concealed as per site
requirement. of als.Power plug along with
accessories.
M 25.00
NSI-24Providing of Revolving Chair as per Requirement or
as Directed by the engineerNo 1.00
TOTAL (Rs.)