PartekPFA/PTFE ValvesCatalog 4182/USA
Parker Hannifi n CorporationPartek OperationTucson, AZ
Table of Contents
Technical Information ........................................................................................................................................ 3
Manual Valves
MV-1 PTFE Stop Cock Valve ................................................................................................................. 4
MV-6 PTFE Ball Valve ............................................................................................................................ 6
MV-8 PTFE Sampling Valve ................................................................................................................... 8
MV-10 1/4” PFA 2 Way Valve .................................................................................................................. 10
MV-10 1/4” PFA 3 Way Valve .................................................................................................................. 12
MV-11 1/2” PFA 2 Way Valve .................................................................................................................. 14
MV-11 1/2” PFA 3 Way Valve .................................................................................................................. 16
MV-11 1/2” PFA 2 Way Adjustable Valve ................................................................................................. 18
MV-12 1” PFA 2 Way Valve ..................................................................................................................... 20
MV-13 PFA Needle Valve......................................................................................................................... 22
MV-14 PFA Stop Cock Valve .................................................................................................................. 24
MV-16 3/4” PFA 2 Way Valve .................................................................................................................. 26
MV-16 3/4” PFA 3 Way Valve .................................................................................................................. 28
MV-16 3/4” PFA Sampling Valve ............................................................................................................. 30
MV-20 1/4” - 1” PTFE Distribution Valve .................................................................................................. 32
Pneumatic Valves
PV-1 Miniature Pneumatic PTFE Valve ................................................................................................. 34
PV-10 1/4” Pneumatic PFA 2 Way Valve ................................................................................................. 36
PV-10 1/4” Pneumatic PFA 3 Way Valve ................................................................................................. 38
PV-11 1/2” Pneumatic PFA 2 Way Valve ................................................................................................. 40
PV-11 1/2” Pneumatic PFA 3 Way Valve ................................................................................................. 42
PV-11 1/2” Pneumatic PFA 2 Way Adj. Bypass Valve ............................................................................. 44
PV-12 1” Pneumatic PFA 2 Way Valve .................................................................................................... 46
PV-16 3/4” Pneumatic PFA 2 Way Valve ................................................................................................. 48
PV-16 3/4” Pneumatic PFA 3 Way Valve ................................................................................................. 50
PV-16 3/4” Pneumatic PFA Sampling Valve ............................................................................................ 52
PV-20 1/4” - 1” PTFE Distribution Valves ................................................................................................ 54
Other Valves
CV-1 1/4” - 1” PTFE Check Valve ......................................................................................................... 56
RV 1/4” Relief Valve ........................................................................................................................... 58
SV-2 1/4” Solenoid Valve ...................................................................................................................... 60
Offer of Sale ........................................................................................................................................................ 62
Parker Hannifi n CorporationPartek OperationTucson, AZ
3
OverviewPartek produces products that are made from only the fi nest Fuoropolymers available. These Fluoropolymers are
resistant to numerous chemicals and solvents. This information provides only a brief technical overview . For more
comprehensive technical and chemical compatibility information, please ask for Technical Bulletin 0002-T1/USA.
Fluorinated PolymersChemical Properties Electrical Properties Mechanical Properties
• Resistivity to corrosive agents • Low dielectric constant • Flexibility at low temperatures
• Non-solubility • Low dissipation factor • Low coeffi cient of friction
• Long term weatherability • High arc resistance • Stability at high temperatures
• Non-adhesiveness • High surface resistance
• Nonfl ammability • High volume resistivity
PTFE is a fl uorocarbon resin that is isostatically compression molded into various shapes and confi gurations. It is
chemically resistant to all chemicals and solvents with the exception of some molten alkali metals, molten sodium
hydroxide, elemental fl uorine and certain fl uorinating agents. At Partek we use PTFE for machining the bodies and
components of various valves and manifolds. It offers chemical resistance and stability at high temperatures.
Modifi ed PTFE material is used primarily for diaphragms and bellows in our products. This material has the same
processing and chemically resistant characteristics as the standard product but offers superior cycle life and integrity
in diaphragm products.
PFA is a copolymer of tetrafl uoroethylene and perfl uoroalkyl vinyl ether. The resultant polymer contains the carbon-
fl uorine backbone chain typical of PTFE, but unlike PTFE, does not require special fabricating techniques. PFA pellets
have good melt fl ow characteristics that allow for processing via extrusion, compression, blow, transfer and injection
molding methods. It has outstanding chemical and solvent resistant characteristics over a temperature range even
greater than PTFE. PFA is offered in various grades of purity and cleanliness making it the material of choice for the
semiconductor market.
Cv and Kv Formulas
SGP
Q = Kv
Q = Cv
YP
P = Pressure Drop (PSIG)
SG = Specific Gravity
Q = Flow (GPM)
P = Pressure Drop (BAR)
Y = Specific Gravity (kg/cm3)
Q = Flow (LPM)
1 Kv = 14.26 Cv
“CV” fl ow factor is the number of gallons of fl uid that pass
through a given orifi ce area in one minute, at a pressure
drop of 1 PSIG.
“KV” fl ow factor is the number of liters of fl uid that pass
through a given orifi ce area in one minute, at a pressure
drop of 1 bar.
For operation at temperatures above ambient conditions,
please refer to the chart above for reduced pressure ratings.
PERCENT OF RATED PRESSURE VS. TEMPERATURE
204˚C14593+38-51 -18
100
90
80
40
60
70
50
30
20
0
PER
CEN
T O
F R
ATE
D O
PER
ATI
NG
PR
ESSU
RE
OPERATING TEMPERATURE
10
400˚F300200+100-60
Technical Information
Parker Hannifi n CorporationPartek OperationTucson, AZ
4
Product OverviewThe MV-1 PTFE Stop Cock Valve is designed for use in high
purity semiconductor fl uid applications, and is also ideally
suited for ultra-pure water and aggressive chemicals. A
precision-machined PTFE body with a straight through
fl owpath is combined with a PTFE full fl ow orifi ce stem
for maximum fl ow, minimum pressure drop and 1/4” turn
operation. The MV-1 is offered for inline and panel mounted
applications.
FeaturesFull fl ow orifi ce.
The precision machined
stem and body provide
tight shut off and 1/4
turn operation.
Parofl uor O-Ring stem
seals.
Benefi tsMaximum fl ow at the
desired size.
Minimum pressure drop.
High cycle life.
Positive body to stem
seal.
Specifi cationsMaterials of ConstructionWetted: PTFE, Parker Parofl uorTM
Non-wetted: HDPE, PFA, PVC, PVDF, Titanate
Pressure Ranges0 to 60 PSIG (4.1 bar)
Pressure ranges for operation at ambient temperatures. For use
at higher temperatures consult Pressure/Temperature chart on
page 3.
Temperature RangesAmbient: -60° - 212° F (-51° - 100° C)
Fluid: -60° - 400° F (-51° - 204° C)
MV-1 Manual Stop Cock Valve
Parker Hannifi n CorporationPartek OperationTucson, AZ
5
MV-1 Manual Stop Cock Valve
Parfl are model numbers are supplied with PVDF nuts. For PFA nuts add -T to model number.
BRACKETED DIMENSIONSARE IN mm.
PRESSURE DROP VS. FLOW RATEFLOW RATE (lpm)
FLOW RATE (gpm)
DE
LTA
-P (
psi
)
DE
LTA
-P (
bar
)
0 2
5
4
10
6
15
8
20
10
25
12
30
.34
.69
1.03
1.38
1.72
2.077.6 15.1 22.7 30.3 37.9 45.4
.125 Orifice
.188 Orifice
.250 Orifice
.313 Orifice
.375 Orifice
.438 Orifice
4141-1-VM 59.1 8.72 052. YAW2 TPNF"4/1 ]12.54[87.1 ]94.51[16. ]57.13[52.1 ]53.6[52. ]72.33[13.1 ]65.3[41.Ø ]04.52[00.1Ø ]07.21[05.4241-1-VM 59.1 8.72 052. LYAW3 TPNF"4/1 ]12.54[87.1 ]94.51[16. ]57.13[52.1 ]53.6[52. ]72.33[13.1 ]65.3[41.Ø ]04.52[00.1Ø ]07.21[05.4341-1-VM 59.1 8.72 052. TYAW3 TPNF"4/1 ]12.54[87.1 ]94.51[16. ]57.13[52.1 ]53.6[52. ]72.33[13.1 ]65.3[41.Ø ]04.52[00.1Ø ]07.21[05.4126-1-VM 63. 1.5 521. YAW2 eralfraP"4/1 ]12.54[87.1 ]94.51[16. ]57.13[52.1 ]53.6[52. ]72.33[13.1 ]65.3[41.Ø ]04.52[00.1Ø ]07.21[05.4226-1-VM 63. 1.5 521. LYAW3 eralfraP"4/1 ]12.54[87.1 ]94.51[16. ]57.13[52.1 ]53.6[52. ]72.33[13.1 ]65.3[41.Ø ]04.52[00.1Ø ]07.21[05.4326-1-VM 63. 1.5 521. TYAW3 eralfraP"4/1 ]12.54[87.1 ]94.51[16. ]57.13[52.1 ]53.6[52. ]72.33[13.1 ]65.3[41.Ø ]04.52[00.1Ø ]07.21[05.6161-1-VM 00.3 8.24 573. YAW2 TPNF"8/3 ]09.65[42.2 ]08.81[47. ]01.83[05.1 ]07.21[05. ]54.44[57.1 ]80.5[02.Ø ]85.63[44.1Ø ]42.51[06.6261-1-VM 00.3 8.24 573. LYAW3 TPNF"8/3 ]09.65[42.2 ]08.81[47. ]01.83[05.1 ]07.21[05. ]54.44[57.1 ]80.5[02.Ø ]85.63[44.1Ø ]42.51[06.6361-1-VM 00.3 8.24 573. TYAW3 TPNF"8/3 ]09.65[42.2 ]08.81[47. ]01.83[05.1 ]07.21[05. ]54.44[57.1 ]80.5[02.Ø ]85.63[44.1Ø ]42.51[06.6146-1-VM 59.1 8.72 052. YAW2 eralfraP"8/3 ]12.54[87.1 ]94.51[16. ]57.13[52.1 ]53.6[52. ]72.33[13.1 ]65.3[41.Ø ]04.52[00.1Ø ]07.21[05.6246-1-VM 59.1 8.72 052. LYAW3 eralfraP"8/3 ]09.65[42.2 ]08.81[47. ]01.83[05.1 ]07.21[05. ]54.44[57.1 ]80.5[02.Ø ]85.63[44.1Ø ]42.51[06.6346-1-VM 59.1 8.72 052. TYAW3 eralfraP"8/3 ]09.65[42.2 ]08.81[47. ]01.83[05.1 ]07.21[05. ]54.44[57.1 ]80.5[02.Ø ]85.63[44.1Ø ]42.51[06.8181-1-VM 55.6 4.39 834. YAW2 TPNF"2/1 ]09.65[42.2 ]08.81[47. ]01.83[05.1 ]07.21[05. ]54.44[57.1 ]80.5[02.Ø ]85.63[44.1Ø ]42.51[06.8281-1-VM 55.6 4.39 834. LYAW3 TPNF"2/1 ]09.65[42.2 ]08.81[47. ]01.83[05.1 ]07.21[05. ]54.44[57.1 ]80.5[02.Ø ]85.63[44.1Ø ]42.51[06.8381-1-VM 55.6 4.39 834. TYAW3 TPNF"2/1 ]09.65[42.2 ]08.81[47. ]01.83[05.1 ]07.21[05. ]54.44[57.1 ]80.5[02.Ø ]85.63[44.1Ø ]42.51[06.8166-1-VM 00.3 8.24 573. YAW2 eralfraP"2/1 ]09.65[42.2 ]08.81[47. ]01.83[05.1 ]07.21[05. ]54.44[57.1 ]80.5[02.Ø ]85.63[44.1Ø ]42.51[06.8266-1-VM 05.2 7.53 313. LYAW3 eralfraP"2/1 ]09.65[42.2 ]08.81[47. ]01.83[05.1 ]07.21[05. ]54.44[57.1 ]80.[02.Ø ]85.63[44.1Ø ]42.51[06.8366-1-VM 05.2 7.53 313. TYAW3 eralfraP"2/1 ]09.65[42.2 ]08.81[47. ]01.83[05.1 ]07.21[05. ]54.44[57.1 ]80.[02.Ø ]85.63[44.1Ø ]42.51[06.
1.15 [29.21]
1.23 [31.24]
3/8" PARFLARE
1/4" PARFLARE 1/4" FNPT
.50 [12.70]
3/8" FNPT
.50 [12.70]
1/2" FNPT
.63 [16.00]
E(HEX)
D (MAX.)
Ø 2.92 [74.17]
2X
3 WAY 3 WAY2 WAY
STEM TOP
A
B
C (SQ.)
PATTERN
GH
2X
PANEL MTG. HOLE
F2X
H
L T1/2" PARFLARE
1.35 [34.29]
ledoMrebmuN
vC vK ecifirOwolF
.gifnoCtroP
.gifnoC]mm[nisnoisnemiD
A B C D E F G H
Parker Hannifi n CorporationPartek OperationTucson, AZ
6
FeaturesFloating ball design
without o-rings ensures
bubble tight sealing at
high pressure.
Full port design; 1/4
turn operation with low
torque tee handle.
Panel mounting is an
option on all sizes.
Benefi tsBidirectional fl ow to 120
psi liquid or gas; High
cycle life.
Ideal for quick shut-off
in contamination-free
applications.
Ideal for process
instrumentation
applications.
Product OverviewThe MV-6 PTFE Ball Valves are designed for use in high
purity semiconductor applications, and are also ideally
suited for use in ultra-pure water and aggressive chemicals.
All sizes have wetted parts made entirely of PTFE. All valves
are designed full port for minimal fl ow restrictions and are
operated 1/4 turn with minimal torque.
Specifi cationsMaterials of ConstructionWetted: PTFE
Non-wetted: HDPE, PVDF and PVC
Pressure Ranges25” HG vacuum (846 mbar) to 120 PSIG (8.3 bar)
Pressure ranges for operation at ambient temperatures. For use
at higher temperatures consult Pressure/Temperature chart on
page 3.
Temperature RangesAmbient: 41° - 104° F (5° - 40° C)
Fluid: 41° - 104° F (5° - 40° C)
MV-6 Manual Ball Valve
Parker Hannifi n CorporationPartek OperationTucson, AZ
7
ØD
E
A
B
C
MV-6 Manual Ball Valve
PRESSURE DROP VS. FLOW RATEFLOW RATE (lpm)
FLOW RATE (gpm)
DE
LTA
-P (
psi
)
DE
LTA
-P (
bar
)
0 10
1
20
2
30
3
40
4
50
5
60
6
.07
.14
.21
.28
.35
.4138 76 113 151 189 227
1/4" FNPT1/2" FNPT 1" FNPT
BRACKETED DIMENSIONSARE IN mm.
rebmuNledoM vC vK .gifnoCwolF .gifnoCtroP]mm[nisnoisnemiD
A B C D E
0-4141-6-VM 88.1 18.62
FFO/NO
TPNF"4/1 ]49.34[37.1 ]67.61[66. ]19.37[19.2 ]92.05[89.1Ø ]72.33[13.1
0-8181-6-VM 95.6 79.39 TPNF"2/1 ]98.65[42.2 ]06.22[98. ]94.49[27.3 ]80.96[27.2Ø ]08.05[00.2
0-611611-6-VM 60.82 41.004 TPNF"1 ]77.08[81.3 ]03.53[93.1 ]00.721[00.5 ]67.111[04.4Ø ]62.46[35.2
Parker Hannifi n CorporationPartek OperationTucson, AZ
8
FeaturesOne piece precision
machined diaphragm
manufactured from the
latest technology
modifi ed PTFE, provides
over fi ve times the fl ex-
ural life as compared to
conventional PTFE.
Full fl ow through port.
Purge port option.
Benefi tsHigher cycle life result-
ing in less downtime
and lower replacement
costs.
Reduced pressure drop.
Allows system mainte-
nance downstream of
valve without disrupting
main fl ow.
Specifi cationsMaterials of ConstructionWetted: PTFE, Modifi ed PTFE
Non-wetted: PVDF
Pressure Ranges27” HG vacuum (913 mbar) to 120 PSIG (8.3 bar)
Pressure ranges for operation at ambient temperatures. For use
at higher temperatures consult Pressure/Temperature chart on
page 3.
Temperature RangesAmbient: 0° - 212° F (17° -100° C)
Fluid: 0° - 400° F (17° - 204° C)
Product OverviewThe MV-8 PTFE Sampling Valve is designed for use in high
purity semiconductor applications, and is also ideally suited
for ultra-pure water or aggressive chemicals. The design
utilizes a machined PTFE body with precision machined
seat and diaphragm sealing areas. A one piece machined
modifi ed PTFE diaphragm is also utilized for excellent fl ex-
ibility and life. The valve incorporates a full fl ow through port
with a low dead volume down leg. The purge port option
makes this the valve of choice for valve manifold boxes
and distribution systems.
MV-8 Manual Sampling Valve
Parker Hannifi n CorporationPartek OperationTucson, AZ
9
Parfl are model numbers are supplied with PVDF nuts. For PFA nuts add -T to model number.
MV-8 Manual Sampling Valve
STYLE 2
I
D
HF
A1
B
SE
B1C
BE
B1C1C1CE
I
D STYLE 1
P
SIZE)PURGE
N
STYLE 4
I
D
HF
A1
B
A
PO EN
B1C
BGE
B1C1
I
D
STYLE 3
F
A
A1
H
K K1
C1
GE
B1 J1
rebmuNledoMtroPhguorhT troPgnilpmaS troPegruP
troPhguorhT troPgnilpmaS troPegruPvC vK ecifirO vC vK ecifirO vC vK ecifirO
1-4866-8-VM 2.3 7.54 573. 2. 8.2 521. A/N A/N A/N eralfraP"2/1 eralfraP"4/1 A/N1-212166-8-VM 0.31 6.581 526. 6.4 7.56 526. A/N A/N A/N eralfraP"4/3 eralfraP"4/3 A/N
1-82166-8-VM 0.31 6.581 526. 3.2 8.23 573. A/N A/N A/N eralfraP"4/3 eralfraP"2/1 A/N1-46166-8-VM 3.73 6.235 578. 2. 8.2 521. A/N A/N A/N eralfraP"1 eralfraP"4/1 A/N1-616166-8-VM 3.73 6.235 578. 2.7 8.201 578. A/N A/N A/N eralfraP"1 eralfraP"1 A/N10-1-82166-8-VM 0.31 6.581 526. 3.2 8.23 573. 2. 8.2 521. eralfraP"4/3 eralfraP"2/1 eralfraP"4/150-1-82166-8-VM 0.31 6.581 526. 3.2 8.23 573. 1.1 7.51 573. eralfraP"4/3 eralfraP"2/1 eralfraP"2/110-1-212166-8-VM 0.31 6.581 526. 6.4 7.56 526. 2. 8.2 521. eralfraP"4/3 eralfraP"4/3 eralfraP"4/1
10-1-86166-8-VM 3.73 6.235 578. 3.2 8.23 573. 1.1 7.51 573. eralfraP"1 eralfraP"2/1 eralfraP"2/110-1-216166-8-VM 3.73 6.235 578. 6.4 7.56 526. 2. 8.2 521. eralfraP"1 eralfraP"4/3 eralfraP"4/110-1-616166-8-VM 3.73 6.235 578. 2.7 8.201 578. 2. 8.2 521. eralfraP"1 eralfraP"1 eralfraP"4/1
)ni(SNOISNEMID
ELYTS A 1A B 1B C 1C D E F G H I J 1J K 1K N P Q
-VM 1-4866-8 1 05.1 - "2/1 53.1 "4/1 51.1 65. 05.1 - - - 75.2
1-212166-8-VM 2 05.3 26.4 "4/3 64.1 "4/3 64.1 00.1 05.3 21.4 00.3 662.Ø 15.4
1-82166-8-VM 2 00.3 21.4 "4/3 64.1 "2/1 53.1 00.1 00.3 26.3 05.2 662.Ø 15.4
1-46166-8-VM 2 00.3 21.4 "1 08.1 "4/1 51.1 00.1 00.3 26.3 05.2 662.Ø 15.4
1-616166-8-VM 3 05.3 21.4 "1 08.1 "1 08.1 00.1 05.3 21.4 00.3 662.Ø 36.4
10-1-82166-8-VM 4 05.4 05.5 '2/1 53.1 "4/3 64.1 57. 05.2 31.5 00.2 662.Ø 05.4 "4/1 51.1 "4/3 64.1 57. "4/1 57.
50-1-82166-8-VM 4 36.4 57.5 '2/1 53.1 "4/3 64.1 57. 05.2 73.5 00.2 662.Ø 05.4 "2/1 53.1 "4/3 64.1 88. "2/1 29.
10-1-212166-8-VM 4 05.4 05.5 "4/3 64.1 "4/3 64.1 57. 05.2 31.5 00.2 662.Ø 05.4 "4/1 51.1 "4/3 64.1 57. "4/1 57.
10-1-86166-8-VM 4 36.4 57.5 "2/1 53.1 "1 08.1 57. 00.3 73.5 00.2 662.Ø 06.4 "2/1 53.1 "1 08.1 88. "2/1 29.
10-1-216166-8-VM 4 05.4 05.5 "4/3 64.1 "1 08.1 39. 00.3 31.5 40.2 662.Ø 06.4 "4/1 51.1 "1 08.1 57. "4/1 39.
10-1-616166-8-VM 4 05.4 05.5 "1 08.1 "1 08.1 39. 00.3 31.5 45.2 662.Ø 06.4 "4/1 51.1 "1 08.1 57. "4/1 39.
)mm(SNOISNEMID
ELYTS A 1A B 1B C 1C D E F G H I J 1J K 1K N P Q
-VM 1-4866-8 1 1.83 - "2/1 3.43 "4/1 2.92 2.41 1.83 - - - 3.56
1-212166-8-VM 2 9.88 3.711 "4/3 1.73 "4/3 1.73 4.52 9.88 6.401 2.67 67.6Ø 6.411
1-82166-8-VM 2 2.67 6.401 "4/3 1.73 "2/1 3.43 4.52 2.67 9.19 5.36 67.6Ø 6.411
1-46166-8-VM 2 2.67 6.401 "1 7.54 "4/1 2.92 4.52 2.67 9.19 5.36 67.6Ø 6.411
1-616166-8-VM 3 9.88 6.401 "1 7.54 "1 7.54 4.52 9.88 6.401 2.67 67.6Ø 6.711
10-1-82166-8-VM 4 3.411 7.931 '2/1 3.43 "4/3 1.73 1.91 5.36 3.031 8.05 67.6Ø 3.411 "4/1 2.92 "4/3 1.73 1.91 "4/1 1.91
50-1-82166-8-VM 4 6.711 0.641 '2/1 3.43 "4/3 1.73 1.91 5.36 4.631 8.05 67.6Ø 3.411 "2/1 3.43 "4/3 1.73 4.22 "2/1 4.32
10-1-212166-8-VM 4 3.411 7.931 "4/3 1.73 "4/3 1.73 1.91 5.36 3.031 8.05 67.6Ø 3.411 "4/1 2.92 "4/3 1.73 1.91 "4/1 1.91
10-1-86166-8-VM 4 6.711 0.641 "2/1 3.43 "1 7.54 1.91 2.67 4.631 8.05 67.6Ø 8.611 "2/1 3.43 "1 7.54 4.22 "2/1 1.91
10-1-216166-8-VM 4 3.411 7.931 "4/3 1.73 "1 7.54 6.32 2.67 3.031 8.15 67.6Ø 8.611 "4/1 2.92 "1 7.54 1.91 "4/1 6.32
10-1-616166-8-VM 4 3.411 7.931 "1 7.54 "1 7.54 6.32 2.67 3.031 5.46 67.6Ø 8.611 "4/1 2.92 "1 7.54 1.91 "4/1 6.32
Parker Hannifi n CorporationPartek OperationTucson, AZ
10
FeaturesOne piece precision
machined diaphragms
manufactured from
the latest technology
modifi ed PTFE. Provides
over fi ve times the
fl exural life as compared
to conventional PTFE.
Tongue and groove
seat and diaphragm for
positive through fl ow
shut off and diaphragm
to body seal.
PVDF coated stainless
steel spring.
Quarter turn operation
with removable handle
for tamper resistance.
Benefi tsHigh cycle life.
Lower replacement
costs.
Less downtime.
Reduces effects of
corrosive environments.
Eliminates need for
separate lockout device.
Specifi cationsMaterials of ConstructionWetted: PFA, Modifi ed PTFE
Non-wetted: PFA, PVDF, 18-8 SS, Viton seals, PTFE coated SS springs
Pressure RangesForward: 27” HG vacuum (913 mbar) to 80 PSIG (5.5 bar)
Backward: 27” HG vacuum (913 mbar) to 80 PSIG (5.5 bar)
Pressure ranges for operation at ambient temperatures. For use
at higher temperatures consult Pressure/Temperature chart on
page 3.
Temperature RangesAmbient: 0° - 150° F (17° - 66° C)
Fluid: 0° - 266° F (17° - 130° C)
Product OverviewThe MV-10 PFA 2 Way Diaphragm Valve is designed for
use in high purity semiconductor applications. It is also
ideally suited for ultra-pure water and aggressive chemical
or gas applications. The design utilizes a molded high purity
PFA body with precision machined sealing areas. A one
piece machined modifi ed PTFE diaphragm is also utilized
for excellent fl exibility and life. A full 1/4” orifi ce provides
maximum fl ow capability in a compact package.
MV-10 1/4” Manual 2 Way Valve
Parker Hannifi n CorporationPartek OperationTucson, AZ
11
PVDF SCREWCOVER
-10
1/4" PARFLARE1.23
[31.24]1.12
[28.45]
HEX NUTW/ STUD
3/8" PARFLARE3/8" PARGRIP1/4" PARGRIP
1.13 [28.70]
.40 [10.16]
[31.75]
-02
.40 [10.16]
.40 [10.16]
-01
.40 [10.16]
IN
OU
T
.88 [22.35]
APDV
F 1/4"1/4"
ALF
RE
P R
2.20 [55.82]
.13[3.30]MAX
PANELTHK.
1.25 [31.78]
1.15 [29.21]
-00
IN
.050 R[1.30]
.527[13.39] OUT
SCREW
Ø1.250BOLT CIRCLE
Ø1.00/1.02 [25.40/25.91] PANEL HOLE (NOTE: ORIENTATION OF LOCATING SLOT DEPENDENT UPON VALVE/MOUNTING CONFIGURATION.)
LOCATING TAB
POSITION
1/4" FNPT
.56 [14.22]
MOUNTINGCONFIGURATIONS(MV-10-XXXX-XX)
.31 [7.87]
Pargrip models are supplied with PFA nuts. Parfl are models are supplied with PVDF nuts. For PFA nuts add -T to model number.
MV-10 1/4” Manual 2 Way Valve
rebmuNledoM CV KV noitarugifnoCwolF noitarugifnoCtroPXX-noitarugifnoCgnitnuoM
)evobAdetcipeD(
BRACKETED DIMENSIONSARE IN mm.
XX-4401-01-VM 06. 6.8
FFO/NO
TPNF"4/1wercS=00
erauqS08.dutS/wercS=10elcriCtloB52.1ØdutS/wercS=20
srevoCwercSFDVP=01
XX-4302-01-VM 42. 4.3 pirgraP"4/1XX-6402-01-VM 26. 8.8 pirgraP"8/3XX-4206-01-VM 02. 8.2 eralfraP"4/1XX-6406-01-VM 26. 8.8 eralfraP""8/3
1.53 [38.86]
.76 [19.3]
2X .19 [4.83]2X .15 [3.81] 2X R.08 [2.03]
SLOT TYP.
1.25 [31.75] SQ.
.50 [12.7]
.20 [5.08]
seirosseccA noitpircseD
01-BS )yletarapesdloS(.ylnosledom01-XXXX-01-VMdna00-XXXX-01-VMhtiwesuroF.esaBgnitnuoMni-panSFDVP
DE
LTA
-P (
psi
)
0
25
5
20
15
10
DE
LTA
-P (
bar
)
1.72
1.38
1.03
.69
.34
FLOW RATE (lpm)PRESSURE DROP VS. FLOW RATE
1.9 3.8 5.7 7.6 11.39.5
FLOW RATE (gpm)0.5 1.0 1.5 2.0 3.02.5
1/4" Parflare1/4" Pargrip1/4" FNPT 3/8" Parflare & Pargrip
Parker Hannifi n CorporationPartek OperationTucson, AZ
12
FeaturesOne piece precision
machined diaphragms
manufactured from
the latest technology
modifi ed PTFE. Provides
over fi ve times the
fl exural life as compared
to conventional PTFE.
Tongue and groove
seat and diaphragm for
positive through fl ow
shut off and diaphragm
to body seal.
PVDF coated stainless
steel spring.
Quarter turn operation
with removable handle
for tamper resistance.
Benefi tsHigh cycle life.
Lower replacement
costs.
Less downtime.
Reduces effects of
corrosive environments.
Eliminates need for
separate lockout device.
Specifi cationsMaterials of ConstructionWetted: PFA, Modifi ed PTFE
Non-wetted: PFA, PVDF, 18-8 SS, Viton seals, PTFE coated SS springs
Pressure RangesForward: 27” HG vacuum (913 mbar) to 80 PSIG (5.5 bar)
Backward: 27” HG vacuum (913 mbar) to 80 PSIG (5.5 bar)
Pressure ranges for operation at ambient temperatures. For use
at higher temperatures consult Pressure/Temperature chart on
page 3.
Temperature RangesAmbient: 0° - 150° F (17° - 66° C)
Fluid: 0° - 266° F (17° - 130° C)
Product OverviewThe MV-10 PFA 3 Way Diaphragm Valve is designed for
use in high purity semiconductor applications. It is also
ideally suited for ultra-pure water and aggressive chemical
or gas applications. The design utilizes a molded high purity
PFA body with precision machined sealing areas. A one
piece machined modifi ed PTFE diaphragm is also utilized
for excellent fl exibility and life. A full 1/4” orifi ce provides
maximum fl ow capability in a compact package.
MV-10 1/4” Manual 3 Way Valve
Parker Hannifi n CorporationPartek OperationTucson, AZ
13
PVDF SCREWCOVER
-10
1.23 [31.24]
1.12 [28.45]
HEX NUTW/ STUD
3/8" PARFLARE3/8" PARGRIP1/4" PARGRIP
1.13 [28.70]
.40 [10.16]
[31.75]
-02
.40 [10.16]
.40 [10.16]
-01
.40 [10.16]
-00
IN
.050 R[1.30]
.527[13.39] OUT
SCREW
Ø1.250BOLT CIRCLE
Ø1.00/1.02 [25.40/25.91] PANEL HOLE (NOTE: ORIENTATION OF LOCATING SLOT DEPENDENT UPON VALVE/MOUNTING CONFIGURATION.)
1/4" FNPT
.56 [14.22]
MOUNTINGCONFIGURATIONS(MV-10-XXXX-XX)
2.20 [55.82]
COMNC NO
1.15 [29.21]
1.25 [31.78]
.88 [22.35]
LOCATING TAB
POSITION
.13[3.30]MAX
PANELTHK.
.63 [15.90]
AAFFLLAA
RRPPFF
VV
EERR
PPDD
1/4"1/4"
.31 [7.87]
1/4" PARFLARE
BRACKETED DIMENSIONSARE IN mm.
MV-10 1/4” Manual 3 Way Valve
Pargrip models are supplied with PFA nuts. Parfl are models are supplied with PVDF nuts. For PFA nuts add -T to model number.
DE
LTA
-P (
psi
)
0
25
5
20
15
10
DE
LTA
-P (
bar
)
1.72
1.38
1.03
.69
.34
FLOW RATE (lpm)PRESSURE DROP VS. FLOW RATE
1.9 3.8 5.7 7.6 11.39.5
FLOW RATE (gpm)0.5 1.0 1.5 2.0 3.02.5
1/4" Parflare1/4" Pargrip1/4" FNPT 3/8" Parflare & Pargrip
seirosseccA noitpircseD
01-BS )yletarapesdloS(.ylnosledom01-XXXX-01-VMdna00-XXXX-01-VMhtiwesuroF.esaBgnitnuoMni-panSFDVP
1.53 [38.86]
.76 [19.3]
2X .19 [4.83]2X .15 [3.81] 2X R.08 [2.03]
SLOT TYP.
1.25 [31.75] SQ.
.50 [12.7]
.20 [5.08]
rebmuNledoM CV KV noitarugifnoCwolF noitarugifnoCtroPXX-noitarugifnoCgnitnuoM
)evobAdetcipeD(
XX-4431-01-VM 06. 6.8
YAW3
TPNF"4/1wercS=00
erauqS08.dutS/wercS=10elcriCtloB52.1ØdutS/wercS=20
srevoCwercSFDVP=01
XX-4332-01-VM 42. 4.3 pirgraP"4/1XX-6432-01-VM 26. 8.8 pirgraP"8/3XX-4236-01-VM 02. 8.2 eralfraP"4/1XX-6436-01-VM 26. 8.8 eralfraP""8/3
Parker Hannifi n CorporationPartek OperationTucson, AZ
14
FeaturesOne piece precision
machined diaphragm
manufactured from
the latest technology
modifi ed PTFE. Provides
over fi ve times the
fl exural life as compared
to conventional PTFE.
Tongue and groove
seat and diaphragm for
positive through fl ow
shut off and diaphragm
to body seal.
PVDF coated stainless
steel spring.
Submergible option
isolates all valve
components from the
external environment.
Benefi tsHigh cycle life.
Lower replacement
costs.
Less downtime.
Reduces effects of
corrosive environments.
Valve remains functional
while operating in wet
or gaseous corrosive
environments.
Specifi cationsMaterials of ConstructionWetted: PFA, Modifi ed PTFE
Non-wetted: PFA, PVDF, Viton seals, PTFE coated SS springs
Pressure RangesForward: 27” HG vacuum (913 mbar) to 100 PSIG (7 bar)
Backward: 27” HG vacuum (913 mbar) to 100 PSIG (7 bar)
Pressure ranges for operation at ambient temperatures. For use
at higher temperatures consult Pressure/Temperature chart on
page 3.
Temperature RangesAmbient: 0° - 150° F (17° - 66° C)
Fluid: 0° - 266° F (17° - 130° C)
Product OverviewThe MV-11 PFA 2 Way Diaphragm Valve is designed for
use in high purity semiconductor applications. It is also
ideally suited for ultra-pure water and aggressive chemical
or gas applications. The design utilizes a molded high purity
PFA body with precision machined sealing areas. A one
piece machined modifi ed PTFE diaphragm is also utilized
for excellent fl exibility and life. A full 1/2” orifi ce provides
maximum fl ow capability in a compact package.
MV-11 1/2” Manual 2 Way Valve
Parker Hannifi n CorporationPartek OperationTucson, AZ
15
.375 [9.52]MAX. PANEL
WIDTH
4.98 [126.47]
2X .26 [6.60]
1.81 [46.05]
2.02 [51.33]
.55 [14.00]
Ø2.90[Ø73.66]
1/2" FNPT 3/4" PARFLARE
1/2" PARFLARE
OUT OUT
Ø1.437 [36.50]
PANEL HOLE DETAIL
PORTPORT
2X Ø.125[Ø3.18]
2.36 [59.94]
1.74 [44.17]
2.31 [58.75]
2.05 [52.10]
1/2" PARBOND 3/4" PARBOND
OUT
2.02 [51.33]
OUT
1.63 [41.35]
1.56 [39.65]
.75 [19.05]
IN
TEST PORT CONNECTION, 1/4-28 UNF
BRACKETED DIMENSIONSARE IN mm.
MV-11 1/2” Manual 2 Way Valve
Parfl are models are supplied with PVDF nuts. For PFA nuts add -T to model number.
100-11-VM 3.2 8.23
FFO/NO
eralfraP"2/1200-11-VM 7.3 8.25 eralfraP"4/3300-11-VM 7.3 8.25 dnobraP"2/1400-11-VM 7.3 8.25 dnobraP"4/3500-11-VM 7.3 8.25 TPNF"2/1
rebmuNledoM vC vK noitarugifnoCwolF noitarugifnoCtroP
PRESSURE DROP VS. FLOW RATEFLOW RATE (lpm)
FLOW RATE (gpm)
DE
LTA
-P (
psi
)
DE
LTA
-P (
bar
)
0 5
4
10
8
15
12
20
16
25
20
30
24
.28
.56
.84
1.12
1.40
1.6519 38 57 76 95 113
1/2" ParfareAll Other Configurations
Parker Hannifi n CorporationPartek OperationTucson, AZ
16
FeaturesOne piece precision
machined diaphragm
manufactured from
the latest technology
modifi ed PTFE. Provides
over fi ve times the
fl exural life as compared
to conventional PTFE.
Tongue and groove
seat and diaphragm for
positive through fl ow
shut off and diaphragm
to body seal.
PVDF coated stainless
steel spring.
Submergible option
isolates all valve
components from the
external environment.
Benefi tsHigh cycle life.
Lower replacement
costs.
Less downtime.
Reduces effects of
corrosive environments.
Valve remains functional
while operating in wet
or gaseous corrosive
environments.
Specifi cationsMaterials of ConstructionWetted: PFA, Modifi ed PTFE
Non-wetted: PFA, PVDF, Viton seals, PTFE coated SS springs
Pressure RangesCOM to NO: 27” HG vacuum (913 mbar) to 80 PSIG (5.5 bar)
COM to NC: 27” HG vacuum (913 mbar) to 25 PSIG (1.7 bar) minimum
NC to COM: 27” HG vacuum (913 mbar) to 80 PSIG (5.5 bar)
with 50 PSIG (3.4 bar) maximum back pressure
Pressure ranges for operation at ambient temperatures. For use
at higher temperatures consult Pressure/Temperature chart on
page 3.
Temperature RangesAmbient: 0° - 150° F (17° - 66° C)
Fluid: 0° - 266° F (17° - 130° C)
Product OverviewThe MV-11 PFA 3 Way Diaphragm Valve is designed for use
in high purity semiconductor applications. It is also ideally
suited for ultra-pure water and aggressive chemical or gas
applications. The design utilizes a molded high purity PFA
body with precision machined sealing areas. One piece
machined modifi ed PTFE diaphragms are also utilized
for excellent fl exibility and life. A full 1/2” orifi ce provides
maximum fl ow capability in a compact package.
MV-11 1/2” Manual 3 Way Valve
Parker Hannifi n CorporationPartek OperationTucson, AZ
17
1/2" FNPT
NO
3/4" PARFLARE
2.01 [50.93]
2.06 [52.25]
NO
1/2" PARBOND
2.06 [52.25]
NO
3/4" PARBOND
NO
.375 [9.52] MAX.PANEL WIDTH
NC
"1/2
APDVP
F
COM
REA
LF
R
1.82 [46.20]
5.87 MAX. [149.07]
Ø1.636 [41.55]
1.58 [40.18]
2.88 [73.03]
MOUNTING DETAIL
Ø1.44 [36.58]
2X .68 [17.32]
[1.65]2X R .065
PANEL HOLE DETAIL
.57 [14.40]
Ø2.93
2X Ø.26
3.23 [82.12]
2.60 [65.96]
1.30 [33.07]
[74.42]
[6.60]
1/2" PARFLARE
TEST PORT CONNECTIONS, 1/4-28 UNF
BRACKETED DIMENSIONSARE IN mm.
MV-11 1/2” Manual 3 Way Valve
Parfl are models are supplied with PVDF nuts. For PFA nuts add -T to model number.
rebmuNledoM vC vK noitarugifnoCwolF noitarugifnoCtroP
120-11-VM 9.1 1.72
YAW3
eralfraP"2/1220-11-VM 8.2 0.04 eralfraP"4/3320-11-VM 8.2 0.04 dnobraP"2/1420-11-VM 8.2 0.04 dnobraP"4/3520-11-VM 8.2 0.04 TPNF"2/1
PRESSURE DROP VS. FLOW RATEFLOW RATE (lpm)
FLOW RATE (gpm)
DE
LTA
-P (
psi
)
DE
LTA
-P (
bar
)
0 5
4
10
8
15
12
20
16
25
20
30
24
.28
.56
.84
1.12
1.40
1.6519 38 57 76 95 113
1/2" ParfareAll Other Configurations
Parker Hannifi n CorporationPartek OperationTucson, AZ
18
FeaturesOne piece precision
machined diaphragm
manufactured from
the latest technology
modifi ed PTFE. Provides
over fi ve times the
fl exural life as compared
to conventional PTFE.
Tongue and groove
diaphragm to body
seal assures leak free
operation.
PVDF coated stainless
steel spring.
Multi-turn operation.
Removable handle.
Benefi tsHigh cycle life.
Lower replacement
costs.
Less downtime.
Reduces effects of
corrosive environments.
Precise fl ow
adjustment.
Eliminates need for
separate lockout device.
Specifi cationsMaterials of ConstructionWetted: PFA, Modifi ed PTFE
Non-wetted: PFA, PVDF, Viton seals, PTFE coated SS springs
Pressure RangesForward: 27” HG vacuum (913 mbar) to 100 PSIG (7 bar)
Backward: 27” HG vacuum (913 mbar) to 100 PSIG (7 bar)
Pressure ranges for operation at ambient temperatures. For use
at higher temperatures consult Pressure/Temperature chart on
page 3.
Temperature RangesAmbient: 0° - 150° F (17° - 66° C)
Fluid: 0° - 266° F (17° - 130° C)
Product OverviewThe MV-11 PFA Adjustable Diaphragm Valve is designed
for use in high purity semiconductor applications. It is also
ideally suited for ultra-pure water and aggressive chemical
or gas applications. The design utilizes a molded high
purity PFA body with precision machined sealing areas.
A one piece machined modifi ed PTFE diaphragm is also
utilized for excellent fl exibility and life. Multi-turn capability
allows precise fl ow adjustment. A full 1/2” orifi ce provides
maximum fl ow capability in a compact package.
MV-11 1/2” Manual 2 Way Adjustable Valve
Parker Hannifi n CorporationPartek OperationTucson, AZ
19
.375 [9.52]MAX. PANEL
WIDTH
3/4" PARFLARE
OUTOUT
1/2" FNPT
Ø2.90[Ø73.66]
2X Ø1.25[Ø3.18]
1.81 [46.05]
2X .26 [6.60]
.55 [14.00]
2.02 [51.33]
4.96 [125.98]
PORT
Ø1.437 [36.50]
PORT
PANEL HOLE DETAIL
1/2" PARFLARE
2.36 [59.94]
1.74 [44.17]
2.31 [58.75]
1.63 [41.35]
1.56 [39.65]
.75 [19.05]
IN
OUT
2.05 [52.10]
1/2" PARBOND 3/4" PARBOND
2.02 [51.33]
OUT
TEST
TEST PORT CONNECTION, 1/4-28 UNF
BRACKETED DIMENSIONSARE IN mm.
MV-11 1/2” Manual 2 Way Adjustable Valve
Parfl are models are supplied with PVDF nuts. For PFA nuts add -T to model number.
rebmuNledoM vC vK noitarugifnoCwolF noitarugifnoCtroP
102-11-VM 3.2 8.23
.JDA
eralfraP"2/1202-11-VM 7.3 8.25 eralfraP"4/3302-11-VM 7.3 8.25 dnobraP"2/1402-11-VM 7.3 8.25 dnobraP"4/3502-11-VM 7.3 8.25 TPNF"2/1
PRESSURE DROP VS. FLOW RATEFLOW RATE (lpm)
FLOW RATE (gpm)
DE
LTA
-P (
psi
)
DE
LTA
-P (
bar
)
0 5
4
10
8
15
12
20
16
25
20
30
24
.28
.56
.84
1.12
1.40
1.6519 38 57 76 95 113
1/2" ParfareAll Other Configurations
Parker Hannifi n CorporationPartek OperationTucson, AZ
20
FeaturesOne piece precision
machined diaphragm
manufactured from
the latest technology
modifi ed PTFE. Provides
over fi ve times the
fl exural life as compared
to conventional PTFE.
Tongue and groove
seat and diaphragm for
positive through fl ow
shut off and diaphragm
to body seal.
PVDF coated stainless
steel spring.
Submergible option
isolates all valve
components from the
external environment.
Benefi tsHigh cycle life.
Lower replacement
costs.
Less downtime.
Reduces effects of
corrosive environments.
Valve remains functional
while operating in wet
or gaseous corrosive
environments.
Specifi cationsMaterials of ConstructionWetted: PFA, Modifi ed PTFE
Non-wetted: PFA, PVDF, Viton seals, PTFE coated SS springs
Pressure RangesForward: 27” HG vacuum (913 mbar) to 100 PSIG (7 bar)
Backward: 27” HG vacuum (913 mbar) to 100 PSIG (7 bar)
Pressure ranges for operation at ambient temperatures. For use
at higher temperatures consult Pressure/Temperature chart on
page 3.
Temperature RangesAmbient: 0° - 150° F (-17° - 66° C)
Fluid: 0° - 266° F (-17° - 130° C)
Product OverviewThe MV-12 PFA Diaphragm Valve is designed for use in
high purity semiconductor applications, and is also ideally
suited for ultra-pure water and aggressive chemical or gas
applications. The design utilizes a molded high purity PFA
body with precision machined seat and diaphragm sealing
areas. A one piece machined modifi ed PTFE diaphragm
is also utilized for excellent fl exibility and life. The valve
requires three full turns from the fully closed to fully open
position. A full 1” orifi ce provides maximum fl ow capability
in a compact package.
MV-12 1” Manual 2 Way Valve
Parker Hannifi n CorporationPartek OperationTucson, AZ
21
AIR AND TEST PORTCONNECTIONS, 1/8” FNPT
BRACKETED DIMENSIONSARE IN mm.
MV-12 1” Manual 2 Way Valve
Parfl are models are supplied with PVDF nuts. For PFA nuts add -T to model number.
7.037.03[178.56][178.56]
1.071.07 [27.23] [27.23]
4.004.00 [101.70] [101.70]
2.322.32 [58.85] [58.85]
PARBONDPARBOND 3/4" 3/4"
PARFLARE PARFLARE 3/4" 3/4"
2.282.28 [57.96] [57.96]
2.592.59 [65.86] [65.86]
PARFLARE PARFLARE 1" 1"
Ø4.22Ø4.22 [Ø107.19] [Ø107.19]
2X Ø.282X Ø.28 [Ø7.11] [Ø7.11]
3.753.75 [95.35] [95.35]
1.881.88 [47.68] [47.68]
1" PARBOND1" PARBOND
4.284.28 [108.81] [108.81]
2.562.56 [65.00] [65.00]
AIR
INOUT
TEST
.26.26[6.60][6.60]
Part Number Cv Kv Flow Confi guration Port Confi guration
MV-12-001 15.7 224.2
ON/OFF
1” Parbond
MV-12-002 13.3 189.9 1” Parfl are
MV-12-003 9.6 142.8 3/4” Parbond
MV-12-004 6.8 142.8 3/4” Parfl are
PRESSURE DROP VS. FLOW RATE
FLOW RATE (lpm)
FLOW RATE (gpm)
DE
LTA
-P (
psi
)
DE
LTA
-P (
bar
)
0 10
10
20
20
30
30
40
40
50
50
60
60
.7
1.4
2.1
2.8
3.5
4.238 76 113 151 189 227
3/4" Parflare
3/4" Parbond
1" Parflare
1" Parbond
Parker Hannifi n CorporationPartek OperationTucson, AZ
22
FeaturesOne piece PFA stem/
handle and bodies.
PFA stem stop.
Angle and straight
through confi gurations,
with numerous end
confi gurations including
Parfl are available.
Specifi cationsMaterials of ConstructionWetted: PFA, PTFE
Non-wetted: PFA, ETFE, PVDF
Pressure Ranges27” HG vacuum (913 mbar) to 100 PSIG (7 bar)
Pressure ranges for operation at ambient temperatures. For use
at higher temperatures consult Pressure/Temperature chart on
page 3.
Temperature RangesAmbient: 0° - 212° F (17° - 100° C)
Fluid: 0° - 266° F (17° - 130° C)
Benefi tsHigh strength and
corrosion resistance.
Safer operation.
Reduces connections,
mounting space, and
overall cost.
Product OverviewThe MV-13 PFA Needle Valve is designed for high purity
or aggressive chemical and gas applications. The design
utilizes a molded high purity PFA body and stem as the only
wetted components. The stem sealing area is precision
machined for smooth, consistent fl ow. A PTFE ferrule
assures a leak tight seal between stem and body. A PFA
stem stop prevents removal of stem from body during
operation. The MV-13 is available in straight through and
angle confi gurations, several orifi ce sizes, and numerous
end connections.
MV-13 Manual Needle Valve
Parker Hannifi n CorporationPartek OperationTucson, AZ
23
Ø .26[6.48]
Ø 1.50[38.1]
Ø .63 [16.00] .69 [17.53]
1.35 [34.29]
1.23 [31.24]
.56 [14.22]
.57 [14.35]
1.15 [29.21]
1.33 [33.76]
1/2" PARGRIP
1.12 [28.45]
3/8" PARGRIP
.38 [9.52]MAX. PANEL
WIDTH
1/4" PARGRIP
1/8" PARGRIP
.52 [13.28]
1.87 [47.57] (MAX.)
1.13 [28.70]
3/8" PARFLARE
1/4" PARFLARE
.75 [19.05]
1/2" PARFLARE
3.83 [97.35](MAX.)
1.05 [26.54]
5.06[128.52](MAX.)
3.31[84.07](MAX.)
.31 [7.92]
DETAILPANEL HOLE
.52 [13.26]
1/4" FNPT
1/8" FNPT
INLINE ANGLED
1/4" MNPT
.55 [13.97]
Parfl are and Pargrip model numbers are supplied with PFA nuts.
MV-13 Manual Needle Valve
rebmuNledoM eziSecifirO noitarugifnoCtroPteltuO/telnI noitarugifnoCwolF
001-31-VM 360. pirgraP"8/1XpirgraP"8/1
thgiartS
401-31-VM 360. eralfraP"4/1XeralfraP"4/1501-31-VM 360. eralfraP"4/1XTPNM"4/1021-31-VM 521. pirgraP"4/1XpirgraP"4/1421-31-VM 521. eralfraP"8/3XeralfraP"8/3521-31-VM 521. eralfraP"2/1XeralfraP"2/1621-31-VM 521. TPNF"8/1XTPNF"8/1361-31-VM 881. pirgraP"8/3XpirgraP"8/3661-31-VM 881. pirgraP"2/1XpirgraP"2/1071-31-VM 881. TPNF"4/1XTPNF"4/1222-31-VM 521. eralfraP"4/1XeralfraP"4/1
elgnA322-31-VM 521. TPNF"4/1XTPNF"4/1522-31-VM 521. eralfraP"8/3XeralfraP"8/3
Cv / Kv vs. TURNS
TURNS
Cv
Kv
0 1
0.1
2
0.2
3
0.3
4
0.4
5
0.5
6
0.6
1.43
2.86
4.28
5.71
7.14
8.57
.188 - All Configurations
.125 - All But 1/4" Pargrip
.125 - All Angle Configurations
.125 - 1/4" Pargrip
.063 - All But 1/8" Pargrip
.063 - 1/8" Pargrip
BRACKETED DIMENSIONSARE IN mm.
Parker Hannifi n CorporationPartek OperationTucson, AZ
24
Product OverviewThe MV-14 PFA 2 Way Stop Cock Valve is designed
for use in high purity semiconductor applications. The
design utilizes a molded high purity PFA body, and a
machined PTFE stem. The press-fi t stem assures a leak
tight seal between it and the body during operation. Valve
operates with a quick 90° turn operation and has a full
1/8” orifi ce.
MV-14 Manual 2 Way Stop Cock Valve
Specifi cationsMaterials of ConstructionWetted: PFA, PTFE
Non-wetted: PFA, PVDF
Pressure Ranges0 to 60 PSIG (4.1 bar)
Pressure ranges for operation at ambient temperatures. For use
at higher temperatures consult Pressure/Temperature chart on
page 3.
Temperature RangesAmbient: 0° - 150° F (17° - 66° C)
Fluid: 0° - 266° F (17° - 130° C)
FeaturesOne piece precision
machined stem and
molded high purity PFA
body.
All components made
of chemical resistant
materials.
Numerous end
confi gurations,
including Parfl are
available.
Benefi tsMaintains system purity.
Suitable for use in
corrosive environments.
Allows direct
installation, minimizing
additional connections,
reducing cost.
Parker Hannifi n CorporationPartek OperationTucson, AZ
25
1.05 [26.67]
.55 [13.97]
.95 [24.13]
1.63 [41.28]
1.33 [33.66]
[29.21]1.15
1.18 [29.97]
[13.97].55
1.13 [28.70]
.75 [19.05]
1/4" REDI-FLARE
1/8" MNPT
1/4" MNPT
1/8" PARGRIP
1/4" PARGRIP
1/4" PARFLARE
Pargrip models are supplied with PFA nuts. Parfl are models are supplied with PVDF nuts. For PFA nuts add -T to model number.
BRACKETED DIMENSIONSARE IN mm.
MV-14 Manual 2 Way Stop Cock Valve
rebmuNledoM CV KV noitarugifnoCwolF troPtelnI troPteltuO
300-41-VM 72. 58.3
FFO/NO
pirgraP"4/1 pirgraP"4/1400-41-VM 72. 58.3 pirgraP"4/1 TPNM"8/1500-41-VM 72. 58.3 pirgraP"4/1 TPNM"4/1600-41-VM 72. 58.3 TPNM"4/1 TPNM"4/1700-41-VM 72. 58.3 eralfraP"4/1 eralfraP"4/1510-41-VM 72. 58.3 eralfraP"4/1 TPNM"4/1610-41-VM 72. 58.3 eralfraP"4/1 eralf-ideR"4/1810-41-VM 72. 58.3 pirgraP"8/1 pirgraP"8/1
DE
LTA
-P (
psi
)
0
25
5
20
15
10
DE
LTA
-P (
bar
)
1.72
1.38
1.03
.69
.34
FLOW RATE (lpm)PRESSURE DROP VS. FLOW RATE
1.9 3.8 5.7 7.6 11.39.5
FLOW RATE (gpm)0.5 1.0 1.5 2.0 3.02.5
All Configurations
Parker Hannifi n CorporationPartek OperationTucson, AZ
26
Product OverviewThe MV-16 PFA diaphragm valve is designed for use in
high purity semiconductor applications, and is also ideally
suited for ultra-pure water and aggressive chemical or gas
applications. The design utilizes a molded high purity PFA
body with precision machined seat and diaphragm sealing
areas. A one piece machined modifi ed PTFE diaphragm
is also utilized for excellent fl exibility and life. The MV-16’s
multi-turn capability allows precise fl ow adjustment. A full
3/4” orifi ce provides maximum fl ow capability in a compact
package.
MV-16 3/4” Manual PFA 2 Way Valve
FeaturesOne piece precision
machined diaphragm
manufactured from
the latest technology
modifi ed PTFE. Provides
over fi ve times the
fl exural life as compared
to conventional PTFE.
Tongue and groove
seat and diaphragm for
positive through fl ow
shut off and diaphragm
to body seal.
Halar coated stainless
steel spring.
Benefi tsHigh cycle life.
Lower replacement
costs.
Less downtime.
Reduces effects of
corrosive environments.
Specifi cationsMaterials of ConstructionWetted: PFA, Modifi ed PTFE
Non-wetted: PVDF, Viton, PTFE coated SS spring
Pressure Ranges0 - 120 PSIG (8.3 bar) See Cracking Pressure Chart on next page.
Pressure ranges for operation at ambient temperatures. For use
at higher temperatures consult Pressure/Temperature chart on
page 3.
Temperature RangesAmbient: 0° - 150° F (-17° - 66° C)
Fluid: 0° - 266° F (-17° - 130° C)
Parker Hannifi n CorporationPartek OperationTucson, AZ
27
2.73 [69.3 mm]
3.43 [87.1 mm]
6.21 [157.8 mm]
A
1.70 [43.2 mm]
Ø4.38 [Ø111.3 mm]
4X .28[7.1 mm]
Ø3.75 [Ø95.3 mm]
4X 75˚EQUALLYSPACED
AIR PORT CONNECTION, 1/8” FNPTTEST PORT CONNECTION, 1/4-28 UNF
BRACKETED DIMENSIONSARE IN mm.
Parfl are models are supplied with PVDF nuts. For PFA nuts add -T to model number.
*Ends are fused on.
MV-16 3/4” Manual PFA 2 Way Valve
rebmuNledoM CV KV noitarugifnoCwolF noitarugifnoCtroP]mm[ninoisnemiD
A
2160-61-VM 8.5 7.28
FFO/NO
eralfraP"4/3 ]27.041[45.5
10-2160-61-VM 8.5 7.28 gnoLeralfraP"4/3 ]95.461[84.6
6160-61-VM 9.7 6.211 *eralfraP"1 ]56.132[21.9
2170-61-VM 9.7 6.211 dnobraP"4/3 ]68.941[09.5
CRACKING PRESSURE
PRESSURE TO INLET PORT (bar)
PRESSURE TO INLET PORT (psi)
PR
ES
SU
RE
TO
OU
TL
ET
PO
RT
(p
si)
PR
ES
SU
RE
TO
OU
TL
ET
PO
RT
(b
ar)
0 24
24
48
48
72
72
96
96
120
120
144
144
1.7
3.3
5.0
6.6
8.3
9.91.7 3.3 5.0 6.6 8.3 9.9
SPECIFIED SEALING AREA
PRESSURE DROP VS. FLOW RATE
FLOW RATE (lpm)
FLOW RATE (gpm)
DE
LTA
-P (
psi
)
DE
LTA
-P (
bar
)
0 10
10
20
20
30
30
40
40
50
50
60
60
.7
1.4
2.1
2.8
3.5
4.238 76 113 151 189 227
3/4" Parflare 3/4" Parbond, 1" Parflare
Parker Hannifi n CorporationPartek OperationTucson, AZ
28
Product OverviewThe MV-16 PFA diaphragm valve is designed for use in
high purity semiconductor applications, and is also ideally
suited for ultra-pure water and aggressive chemical or gas
applications. The design utilizes a molded high purity PFA
body with precision machined seat and diaphragm sealing
areas. A one piece machined modifi ed PTFE diaphragm
is also utilized for excellent fl exibility and life. The MV-16’s
multi-turn capability allows precise fl ow adjustment. A full
3/4” orifi ce provides maximum fl ow capability in a compact
package.
MV-16 3/4” Manual PFA 3 Way Valve
FeaturesOne piece precision
machined diaphragm
manufactured from
the latest technology
modifi ed PTFE. Provides
over fi ve times the
fl exural life as compared
to conventional PTFE.
Tongue and groove
seat and diaphragm for
positive through fl ow
shut off and diaphragm
to body seal.
Halar coated stainless
steel spring.
Benefi tsHigh cycle life.
Lower replacement
costs.
Less downtime.
Reduces effects of
corrosive environments.
Specifi cationsMaterials of ConstructionWetted: PFA, Modifi ed PTFE
Non-wetted: PVDF, Viton, PTFE coated SS spring
Pressure Ranges0 - 120 PSIG (8.3 bar) See Cracking Pressure Chart on next page.
Pressure ranges for operation at ambient temperatures. For use
at higher temperatures consult Pressure/Temperature chart on
page 3.
Temperature RangesAmbient: 0° - 150° F (-17° - 66° C)
Fluid: 0° - 266° F (-17° - 130° C)
Parker Hannifi n CorporationPartek OperationTucson, AZ
29
2.69 [68.4 mm]
3.39 [86.2 mm]
1.66 [42.2 mm]
6.44 [163.4 mm]
Ø4.38 [Ø111.3 mm]
4X .28[7.1 mm]
Ø3.75 [Ø95.3 mm]
4X 75˚EQUALLYSPACED
AB
Parfl are models are supplied with PVDF nuts. For PFA nuts add -T to model number.
*Ends are fused on.
MV-16 3/4” Manual PFA 3 Way ValveBRACKETED DIMENSIONS
ARE IN mm.
AIR PORT CONNECTION, 1/8” FNPTTEST PORT CONNECTION, 1/4-28 UNF
rebmuNledoM CV KV noitarugifnoCwolF noitarugifnoCtroP]mm[nisnoisnemiD
A B
2163-61-VM 4.5 0.77
YAW3
CNMOC
ON
eralfraP"4/3 ]27.041[45.5 ]73.17[18.2
10-2163-61-VM 4.5 0.77 gnoLeralfraP"4/3 ]95.461[84.6 ]73.17[18.2
6163-61-VM 3.7 1.401 *eralfraP"1 ]56.132[21.9 ]28.511[65.4
2173-61-VM 3.7 1.401 dnobraP"4/3 ]68.941[09.5 ]39.47[59.2
2164-61-VM 4.5 0.77
stroPdesreveRYAW3
ONMOC
CN
eralfraP"4/3 ]27.041[45.5 ]73.17[18.2
10-2164-61-VM 4.5 0.77 gnoLeralfraP"4/3 ]95.461[84.6 ]73.17[18.2
6164-61-VM 3.7 1.401 *eralfraP"1 ]56.132[21.9 ]28.511[65.4
2174-61-VM 3.7 1.401 dnobraP"4/3 ]68.941[09.5 ]39.47[59.2
CRACKING PRESSURE
PRESSURE TO INLET PORT (bar)
PRESSURE TO INLET PORT (psi)
PR
ES
SU
RE
TO
OU
TL
ET
PO
RT
(p
si)
PR
ES
SU
RE
TO
OU
TL
ET
PO
RT
(b
ar)
0 24
24
48
48
72
72
96
96
120
120
144
144
1.7
3.3
5.0
6.6
8.3
9.91.7 3.3 5.0 6.6 8.3 9.9
SPECIFIED SEALING AREA
PRESSURE DROP VS. FLOW RATE
FLOW RATE (lpm)
FLOW RATE (gpm)
DE
LTA
-P (
psi
)
DE
LTA
-P (
bar
)
0 10
10
20
20
30
30
40
40
50
50
60
60
.7
1.4
2.1
2.8
3.5
4.238 76 113 151 189 227
3/4" Parflare 3/4" Parbond, 1" Parflare
Parker Hannifi n CorporationPartek OperationTucson, AZ
30
Product OverviewThe MV-16 PFA sampling valve is designed for use in
high purity semiconductor applications, and is also ideally
suited for ultra-pure water and aggressive chemical or gas
applications. The design utilizes a molded high purity PFA
body with precision machined seat and diaphragm sealing
areas. A one piece machined modifi ed PTFE diaphragm
is also utilized for excellent fl exibility and life. The MV-16’s
multi-turn capability allows precise fl ow adjustment. The
valve incorporates a full fl ow through port with a low dead
volume down leg.
MV-16 3/4” Manual PFA Sampling Valve
FeaturesOne piece precision
machined diaphragm
manufactured from
the latest technology
modifi ed PTFE. Provides
over fi ve times the
fl exural life as compared
to conventional PTFE.
Halar coated stainless
steel spring.
Full fl ow through port.
Benefi tsHigh cycle life.
Lower replacement
costs.
Less downtime.
Reduces effects of
corrosive environments.
Reduced pressure drop.
Specifi cationsMaterials of ConstructionWetted: PFA, Modifi ed PTFE
Non-wetted: PVDF, Viton, PTFE coated SS spring
Pressure Ranges0 - 120 PSIG (8.3 bar) See Cracking Pressure Chart on next page.
Pressure ranges for operation at ambient temperatures. For use
at higher temperatures consult Pressure/Temperature chart on
page 3.
Temperature RangesAmbient: 0° - 150° F (-17° - 66° C)
Fluid: 0° - 266° F (-17° - 130° C)
Parker Hannifi n CorporationPartek OperationTucson, AZ
31
6.49 [164.7 mm]
2.69 [68.4 mm]
3.39 [86.2 mm]
Ø4.38 [Ø111.3 mm]
4X .28[7.1 mm]
Ø3.75 [Ø95.3 mm]
4X 75˚EQUALLYSPACED
1.66 [42.2 mm]
AB
Parfl are models are supplied with PVDF nuts. For PFA nuts add -T to model number.
MV-16 3/4” Manual PFA Sampling Valve
AIR PORT CONNECTION, 1/8” FNPTTEST PORT CONNECTION, 1/4-28 UNF
BRACKETED DIMENSIONSARE IN mm.
rebmuNledoMtroPhguorhT troPelpmaS
troPhguorhT troPelpmaS]mm[nisnoisnemiD
vC vK vC vK A B
806-2165-61-VM 0.31 4.581 3.2 8.23 eralfraP"4/3 eralfraP"2/1 ]27.041[45.5 ]38.86[17.2
216-2165-61-VM 0.31 4.581 6.4 6.56 eralfraP"4/3 eralfraP"4/3 ]27.041[45.5 ]73.17[18.2
217-2165-61-VM 0.31 4.581 9.6 7.89 eralfraP"4/3 dnobraP"4/3 ]27.041[45.5 ]39.47[59.2
806-2175-61-VM 2.52 29.953 3.2 8.23 dnobraP"4/3 eralfraP"2/1 ]68.941[09.5 ]38.86[17.2
216-2175-61-VM 2.52 29.953 6.4 6.56 dnobraP"4/3 eralfraP"4/3 ]68.941[09.5 ]73.17[18.2
217-2175-61-VM 2.52 29.953 9.6 7.89 dnobraP"4/3 dnobraP"4/3 68.941[09.5 ]39.47[59.2
CRACKING PRESSURE
PRESSURE TO THROUGH PORT (bar)
PRESSURE TO THROUGH PORT (psi)
PR
ES
SU
RE
TO
SA
MP
LE
PO
RT
(p
si)
PR
ES
SU
RE
TO
SA
MP
LE
PO
RT
(b
ar)
0 24
24
48
48
72
72
96
96
120
120
144
144
1.7
3.3
5.0
6.6
8.3
9.91.7 3.3 5.0 6.6 8.3 9.9
SPECIFIED SEALING AREA
Parker Hannifi n CorporationPartek OperationTucson, AZ
32
MV-20 1/4” - 1” Manual PTFE Slurry Valve
Product OverviewThe MV-20 slurry valve is designed for use slurry ap-
plications, and is also ideally suited for ultra-pure water
and aggressive chemical or gas applications. The design
utilizes a machined PTFE body with precision machined
seat and diaphragm sealing areas. The valve is offered in
3 orifi ce sizes (1/4”, 1/2” and 1”) and port sizes ranging
from 1/4” to 1 1/4”.
FeaturesFully swept open bowl
diaphragm seat area.
Self draining design.
High load point seat seal.
Angled and rounded internal
fl ow path.
One piece precision
machined diaphragm
manufactured from modifi ed
PTFE.
Evenly distributed seat
sealing forces.
Maximized diaphragm
thickness.
Benefi tsMinimizes fl uid shear and
smooth fl ow transition.
Minimizes area for
entrapment and stagnation
of media.
Improves sealing
mechanism for aggressive
chemicals, deionized water
and abrasive slurry media.
Minimizes particle
contribution of valve.
Provides faster purging and
cleaning of valve.
Less pressure drop
allows for lower pressure
requirements upstream.
Improves fl uid fl ow
dynamics.
Improves cycle life, less
shear than standard PTFE
material, lower replacement
costs, less downtime.
Minimized diaphragm and
valve seat strain.
Stabilizes valve back
pressure capability.
Minimizes potential
for permeation while
maximizing cycle life.
Specifi cationsMaterials of ConstructionWetted: PTFE, Modifi ed PTFE
Non-wetted: PVDF, Viton, PTFE coated SS spring
Pressure Ranges1/4” Orifi ce: 27” HG vacuum (913 mbar) - 80 PSIG (5.5 bar)
1/2” Orifi ce: 27” HG vacuum (913 mbar) - 100 PSIG (7 bar)
1” Orifi ce: 27” HG vacuum (913 mbar) - 100 PSIG (7 bar)
Pressure ranges for operation at ambient temperatures. For use
at higher temperatures consult Pressure/Temperature chart on
page 3.
Temperature RangesAmbient: 0° - 150° F (-17° - 66° C)
Fluid: 0° - 266° F (-17° - 130° C)
Parker Hannifi n CorporationPartek OperationTucson, AZ
33
MV-20 1/4” - 1” Manual PTFE Slurry Valve
Parfl are models are supplied with PVDF nuts. For PFA nuts add -T to model number. Contact factory for Pillar end connections.
Part Number Cv KvBody
SizeValve Type
Port
Confi guration
A B C D E F
inch mm inch mm inch mm inch mm inch mm inch mm
MV-20-04-0604 .20 2.8 1/4” 1/4 TURN
LOTO
1/4” Parfl are 3.80 96.52 1.50 38.10 1.15 29.21 2.91 73.91 1.25 31.75 0.50 12.70
MV-20-04-0606 .76 10.8 1/4” 3/8” Parfl are 3.96 100.58 1.50 38.10 1.15 29.21 2.91 73.91 1.25 31.75 0.50 12.70
MV-20-08-0608 2.4 34.2 1/2”
MULTI-TURN
1/2” Parfl are 5.20 132.08 2.50 63.50 1.80 45.72 5.04 128.02 2.00 50.80 0.78 19.81
MV-20-08-0612 3.9 55.8 1/2” 3/4” Parfl are 5.35 135.89 2.50 63.50 2.00 50.80 5.24 133.10 2.00 50.80 0.83 20.96
MV-20-16-0612 6.4 91.5 1” 3/4” Parfl are 6.22 157.99 3.38 85.85 2.88 73.15 7.05 179.07 3.00 76.20 1.00 25.40
MV-20-16-0616 10.9 155.4 1” 1” Parfl are 6.98 177.29 3.38 85.85 2.88 73.15 7.05 179.07 3.00 76.20 1.00 25.40
MV-20-16-0620 13.5 192.9 1” 1 1/4” Parfl are 8.07 204.98 3.75 95.25 3.25 82.55 7.43 188.72 3.00 76.20 1.25 31.75
BRACKETED DIMENSIONSARE IN mm.
A
F
E
1/4” ORIFICE: 2X Ø.17 THRU, C.B. Ø.28 X .401/2” ORIFICE: 2X Ø.19 THRU, C.B. Ø.31 X .50
1” ORIFICE: 2X Ø.28 THRU, C.B. Ø.44 X 1.00
1/4-28 UNF LEAK DETECTION PORT
D
C
B
1/2” & 1” ORIFICE HOUSING STYLEMULTI-TURN OPERATION
1/4” ORIFICE: 0.18 [4.57]1/2” ORIFICE: 0.25 [6.35] 1” ORIFICE: 0.28 [7.11]
1/4” ORIFICE (ALL PORT CONFIGURATIONS): 0.55 [13.97]1/2” ORIFICE (ALL PORT CONFIGURATIONS): 1.44 [36.58]1” ORIFICE (3/4” & 1” PARFLARE PORT CONFIGURATIONS): 1.50 [38.10]1” ORIFICE (1 1/4” PARFLARE PORT CONFIGURATION): 2.00 [50.80]
1/4” ORIFICE HOUSING STYLE1/4 TURN OPERATION W/ LOTO
PRESSURE DROP VS. FLOW RATEFLOW RATE (lpm)
FLOW RATE (gpm)
DEL
TA-P
(psi
)
DEL
TA-P
(bar
)
0 10
10
20
20
30
30
40
40
50
50
60
60
.7
1.4
2.1
2.8
3.5
4.238 76 113 151 189 227
MV-
20-0
8-06
08
MV-
20-0
8-06
12
MV-
20-1
6-06
12
MV-20-16-0616
MV-20-16-0620
FLOW RATE (lpm)
FLOW RATE (gpm)
DEL
TA-P
(psi
)
DEL
TA-P
(bar
)
0 1
5
2
10
3
15
4
20
5
25
6
30
.34
.69
1.0
1.4
1.7
2.13.8 7.6 11.3 15.1 18.9 22.7
MV-
20-0
4-06
04
MV-
20-0
4-06
06
Parker Hannifi n CorporationPartek OperationTucson, AZ
34
FeaturesPrecision machined
diaphragm
manufactured from
the latest technology
modifi ed PTFE. Provides
over fi ve times the
fl exural life as compared
to conventional PTFE.
Tongue and groove seal
for positive diaphragm
to body seal.
Compact design
actuator works on as
little as 20 psi.
Benefi tsHigh cycle life.
Lower replacement
costs.
Less downtime.
Isolates media from
actuator.
Ease of installation and
maintenance.
Specifi cationsMaterials of ConstructionWetted: PTFE, Modifi ed PTFE
Non-wetted: Anodized Aluminum, SS, Nitrile
Pressure RangesForward: 25” HG vacuum (846 mbar) to 20 PSIG (1.4 bar)
Back: 25” HG vacuum (846 mbar) to 20 PSIG (1.4 bar)
Actuator: 20 PSIG (1.4 bar) to 120 PSIG (8.3 bar)
Pressure ranges for operation at ambient temperatures. For use
at higher temperatures consult Pressure/Temperature chart on
page 3.
Temperature RangesAmbient: -60° - 212° F (-51° - 100° C)
Fluid: -60° - 400° F (-51° - 204° C)
Product OverviewThe PV-1 PTFE Miniature Diaphragm Valve is designed
for use in high purity semiconductor applications, and
is also ideally suited for ultra-pure water and aggressive
chemical systems. The design utilizes a machined modifi ed
PTFE body, seat and diaphragm ensuring excellent
fl exibility and long life. The valve is available in 2 and 3
way confi gurations. It is ideal for low fl ow and small dose
injection applications.
PV-1 Miniature Pneumatic Valve
Parker Hannifi n CorporationPartek OperationTucson, AZ
35
BRACKETED DIMENSIONSARE IN mm.
PV-1 Miniature Pneumatic Valve
/ 81
"RA
RG
P
PFA
PI
1/8" PARGRIP
10-32 UNF-2B
.38
.31 SQ.
Ø.50
B
.82
.23 SQ.
[ 7.94 ]
[ 5.72 ]
[ 9.53 ]
[ 12.64 ]
1/8" FNPT
.19[ 4.83 ]
[ 20.83 ]
rebmuNledoM CV KV noitarugifnoCwolF eziSecifirO noitarugifnoCtroPnoisnemiD
B
4311-1-VP 80. 1.1 CN 490. TPNF"8/1 ]56.9[83.
30-4331-1-VP 80. 1.1 YAW3 490. TPNF"8/1 ]56.9[83.
4312-1-VP 80. 1.1 CN 490. pirgraP"8/1 ]31.8[23.
30-4332-1-VP 80. 1.1 YAW3 490. pirgraP"8/1 ]31.8[23.
DE
LTA
-P (
psi
)
0
50
10
40
30
20
DE
LTA
-P (
bar
)
3.5
2.8
2.1
1.4
.70
FLOW RATE (lpm)PRESSURE DROP VS. FLOW RATE
.38 .76 1.1 1.5 2.31.9
FLOW RATE (gpm).10 .20 .30 .40 .60.50
All Configurations
Parker Hannifi n CorporationPartek OperationTucson, AZ
36
FeaturesOne piece precision
machined diaphragms
manufactured from
the latest technology
modifi ed PTFE. Provides
over fi ve times the
fl exural life as compared
to conventional PTFE.
Tongue and groove
seat and diaphragm for
positive through fl ow
shut off and diaphragm
to body seal.
PVDF coated stainless
steel spring.
Benefi tsHigh cycle life.
Lower replacement
costs.
Less downtime.
Reduces effects of
corrosive environments.
Specifi cationsMaterials of ConstructionWetted: PFA, Modifi ed PTFE
Non-wetted: PFA, PVDF, 18-8 SS, Viton seals, PTFE coated SS springs
Pressure RangesForward: 27” HG vacuum (913 mbar) to 80 PSIG (5.5 bar)
Back: 27” HG vacuum (913 mbar) to 80 PSIG (5.5 bar)
Actuator: 20 PSIG (1.4 bar) to 120 PSIG (8.3 bar)
Pressure ranges for operation at ambient temperatures. For use
at higher temperatures consult Pressure/Temperature chart on
page 3.
Temperature RangesAmbient: 0° - 150° F (-17° - 66° C)
Fluid: 0° - 266° F (-17° - 130° C)
Normally Closed shown
Product OverviewThe PV-10 PFA Diaphragm Valve is designed for use in
high purity semiconductor applications. It is also ideally
suited for ultra-pure water and aggressive chemical or gas
applications. The design utilizes a molded high purity PFA
body with precision machined areas. A one piece machined
modifi ed PTFE diaphragm is also utilized for excellent fl ex-
ibility and life. A full 1/4” orifi ce provides maximum fl ow
capability in a compact package.
PV-10 1/4” Pneumatic 2 Way Valve
Parker Hannifi n CorporationPartek OperationTucson, AZ
37
1/4" PARFLARE
Ø1.75 [44.45]
IN
OU
T
.88 [22.35]
APDV
F 1/4"1/4"
ALF
RE
P R
1.54 [39.12]
1.23 [31.24]
1.12 [28.45]
3/8" PARFLARE3/8" PARGRIP1/4" PARGRIP
1.13 [28.70]
1/4" FNPT
.56 [14.22]
PVDF SCREWCOVER
-10
HEX NUTW/ STUD
.40 [10.16]
[31.75]
-02
.40 [10.16]
.40 [10.16]
-01
.40 [10.16]
-00
IN OUT
SCREW
Ø1.250BOLT CIRCLE
MOUNTINGCONFIGURATIONS(PV-10-XXXX-XX)
1.25 [31.78]
1.15 [29.21]
.31 [7.87]
BRACKETED DIMENSIONSARE IN mm.
PV-10 1/4” Pneumatic 2 Way Valve
AIR PORT CONNECTION, 1/8” FNPT
rebmuNledoM CV KV noitarugifnoCwolF noitarugifnoCtroPXX-noitarugifnoCgnitnuoM
)evobAdetcipeD(
XX-4411-01-VP 06. 6.8 CN TPNF"4/1
wercS=00erauqS08.dutS/wercS=10
elcriCtloB52.1ØdutS/wercS=20srevoCwercSFDVP=01
XX-4421-01-VP 06. 6.8 ON TPNF"4/1XX-4312-01-VP 42. 4.3 CN pirgraP"4/1XX-4322-01-VP 42. 4.3 ON pirgraP"4/1XX-6412-01-VP 26. 8.8 CN pirgraP"8/3XX-6422-01-VP 26. 8.8 ON pirgraP"8/3XX-4216-01-VP 02. 8.2 CN eralfraP"4/1XX-4226-01-VP 02. 8.2 ON eralfraP"4/1XX-6416-01-VP 26. 8.8 CN eralfraP""8/3XX-6426-01-VP 26. 8.8 ON eralfraP""8/3
Pargrip models are supplied with PFA nuts. Parfl are models are supplied with PVDF nuts. For PFA nuts add -T to model number.
DE
LTA
-P (
psi
)
0
25
5
20
15
10
DE
LTA
-P (
bar
)
1.72
1.38
1.03
.69
.34
FLOW RATE (lpm)PRESSURE DROP VS. FLOW RATE
1.9 3.8 5.7 7.6 11.39.5
FLOW RATE (gpm)0.5 1.0 1.5 2.0 3.02.5
1/4" Parflare1/4" Pargrip1/4" FNPT 3/8" Parflare & Pargrip
1.53 [38.86]
.76 [19.3]
2X .19 [4.83]2X .15 [3.81] 2X R.08 [2.03]
SLOT TYP.
1.25 [31.75] SQ.
.50 [12.7]
.20 [5.08]
seirosseccA noitpircseD
01-BS )yletarapesdloS(.ylnosledom01-XXXX-01-VPdna00-XXXX-01-VPhtiwesuroF.esaBgnitnuoMni-panSFDVP
Parker Hannifi n CorporationPartek OperationTucson, AZ
38
FeaturesOne piece precision
machined diaphragms
manufactured from the
latest technology modifi ed
PTFE. Provides over fi ve
times the fl exural life as
compared to conventional
PTFE. Tongue and groove
seat and diaphragm for
positive through fl ow shut
off and diaphragm to body
seal.
PVDF coated stainless
steel springs.
Benefi tsHigh cycle life.
Lower replacement costs.
Less downtime.
Reduces effects of
corrosive environments.
Specifi cationsMaterials of ConstructionWetted: PFA, Modifi ed PTFE
Non-wetted: PFA, PVDF, 18-8 SS, Viton seals, PTFE coated SS springs
Pressure RangesForward: 27” HG vacuum (913 mbar) to 80 PSIG (5.5 bar)
Back: 27” HG vacuum (913 mbar) to 80 PSIG (5.5 bar)
Actuator: 20 PSIG (1.4 bar) to 120 PSIG (8.3 bar)
Pressure ranges for operation at ambient temperatures. For use
at higher temperatures consult Pressure/Temperature chart on
page 3.
Temperature RangesAmbient: 0° - 150° F (-17° - 66° C)
Fluid: 0° - 266° F (-17° - 130° C)
Product OverviewThe PV-10 PFA 3 Way Diaphragm Valve is designed for use
in high purity semiconductor applications. It is also ideally
suited for ultra-pure water and aggressive chemical or gas
applications. The design utilizes a molded high purity PFA
body with precision machined areas. One piece machined
modifi ed PTFE diaphragms are also utilized for excellent
fl exibility and life. A full 1/4” orifi ce provides maximum fl ow
capability in a compact package.
PV-10 1/4” Pneumatic 3 Way Valve
Parker Hannifi n CorporationPartek OperationTucson, AZ
39
1.23 [31.24]
1.12 [28.45]
3/8" PARFLARE3/8" PARGRIP1/4" PARGRIP
1.13 [28.70]
1/4" FNPT
.56 [14.22]
PVDF SCREWCOVER
-10
HEX NUTW/ STUD
.40 [10.16]
[31.75]
-02
.40 [10.16]
.40 [10.16]
-01
.40 [10.16]
-00
IN OUT
SCREW
Ø1.250BOLT CIRCLE
MOUNTINGCONFIGURATIONS(PV-10-XXXX-XX)
Ø1.75 [44.45]
.63 [15.90]
1.54 [39.12]
COMNC NO
.88 [22.35]
AAFFLLAA
RRPPFF
VV
EERR
PPDD
1/4"1/4"
1/4" PARFLARE
1.25 [31.78]
1.15 [29.21].31
[7.87]AIR PORT CONNECTION, 1/8” FNPT
BRACKETED DIMENSIONSARE IN mm.
PV-10 1/4” Pneumatic 3 Way Valve
rebmuNledoM CV KV noitarugifnoCwolF noitarugifnoCtroPXX-noitarugifnoCgnitnuoM
)evobAdetcipeD(
XX-4431-01-VP 06. 6.8
YAW3
TPNF"4/1wercS=00
erauqS08.dutS/wercS=10elcriCtloB52.1ØdutS/wercS=20
srevoCwercSFDVP=01
XX-4332-01-VP 42. 4.3 pirgraP"4/1XX-6432-01-VP 26. 8.8 pirgraP"8/3XX-4236-01-VP 02. 8.2 eralfraP"4/1XX-6436-01-VP 26. 8.8 eralfraP""8/3
Pargrip models are supplied with PFA nuts. Parfl are models are supplied with PVDF nuts. For PFA nuts add -T to model number.
DE
LTA
-P (
psi
)
0
25
5
20
15
10
DE
LTA
-P (
bar
)
1.72
1.38
1.03
.69
.34
FLOW RATE (lpm)PRESSURE DROP VS. FLOW RATE
1.9 3.8 5.7 7.6 11.39.5
FLOW RATE (gpm)0.5 1.0 1.5 2.0 3.02.5
1/4" Parflare1/4" Pargrip1/4" FNPT 3/8" Parflare & Pargrip
seirosseccA noitpircseD
01-BS )yletarapesdloS(.ylnosledom01-XXXX-01-VPdna00-XXXX-01-VPhtiwesuroF.esaBgnitnuoMni-panSFDVP
1.53 [38.86]
.76 [19.3]
2X .19 [4.83]2X .15 [3.81] 2X R.08 [2.03]
SLOT TYP.
1.25 [31.75] SQ.
.50 [12.7]
.20 [5.08]
Parker Hannifi n CorporationPartek OperationTucson, AZ
40
FeaturesOne piece precision
machined diaphragm
manufactured from
the latest technology
modifi ed PTFE. Provides
over fi ve times the
fl exural life as compared
to conventional PTFE.
Tongue and groove
seat and diaphragm for
positive through fl ow
shut off and diaphragm
to body seal.
PVDF coated stainless
steel spring.
Submergible option
isolates all valve
components from the
external environment.
Benefi tsHigh cycle life.
Lower replacement
costs.
Less downtime.
Reduces effects of
corrosive environments.
Valve remains functional
while operating in wet
or gaseous corrosive
environments.
Specifi cationsMaterials of ConstructionWetted: PFA, Modifi ed PTFE
Non-wetted: PFA, PVDF, Viton seals, PTFE coated SS springs
Pressure RangesForward: 27” HG vacuum (913 mbar) to 100 PSIG (7 bar)
Back: 80 PSIG (5.5 bar) with 80 PSIG (5.5 bar) inlet pressure
Actuator: 60 PSIG (4.2 bar) to 100 PSIG (7 bar)
Pressure ranges for operation at ambient temperatures. For use
at higher temperatures consult Pressure/Temperature chart on
page 3.
Temperature RangesAmbient: 0° - 150° F (-17° - 66° C)
Fluid: 0° - 266° F (-17° - 130° C)
Normally Closed Shown
Product OverviewThe PV-11 PFA Diaphragm Valve is designed for use in
high purity semiconductor applications. It is also ideally
suited for ultra-pure water and aggressive chemical or gas
applications. The design utilizes a molded high purity PFA
body with precision machined areas. A one piece machined
modifi ed PTFE diaphragm is also utilized for excellent fl ex-
ibility and life. A full 1/2” orifi ce provides maximum fl ow
capability in a compact package.
PV-11 1/2” Pneumatic 2 Way Valve
Parker Hannifi n CorporationPartek OperationTucson, AZ
41
AIR PORT CONNECTION, 1/8” FNPTTEST PORT CONNECTION, 1/4-28 UNF
BRACKETED DIMENSIONSARE IN mm.
PV-11 1/2” Pneumatic 2 Way Valve
110-11-VP 3.2 8.23
ON
eralfraP"2/1
210-11-VP 7.3 8.25 eralfraP"4/3
310-11-VP 7.3 8.25 dnobraP"2/1
410-11-VP 7.3 8.25 dnobraP"4/3
510-11-VP 7.3 8.25 TPNF"2/1
100-11-VP 3.2 8.23
CN
eralfraP"2/1
200-11-VP 7.3 8.25 eralfraP"4/3
300-11-VP 7.3 8.25 dnobraP"2/1
400-11-VP 7.3 8.25 dnobraP"4/3
500-11-VP 7.3 8.25 TPNF"2/1
rebmuNledoM CV KV .gifnoCwolF .gifnoCtroP rebmuNledoM CV KV .gifnoCwolF .gifnoCtroP
Parfl are models are supplied with PVDF nuts. For PFA nuts add -T to model number.
PRESSURE DROP VS. FLOW RATEFLOW RATE (lpm)
FLOW RATE (gpm)
DE
LTA
-P (
psi
)
DE
LTA
-P (
bar
)
0 5
4
10
8
15
12
20
16
25
20
30
24
.28
.56
.84
1.12
1.40
1.6519 38 57 76 95 113
1/2" ParfareAll Other Configurations
CRACKING PRESSURE
PRESSURE TO INLET PORT (bar)
PRESSURE TO INLET PORT (psi)
PR
ES
SU
RE
TO
OU
TL
ET
PO
RT
(p
si)
PR
ES
SU
RE
TO
OU
TL
ET
PO
RT
(b
ar)
0 25
45
50
90
75
135
100
180
125
225
150
270
3.1
6.2
9.3
12.4
15.5
18.61.7 3.4 5.2 6.9 8.6 10.3
SPECIFIED SEALING AREA
2X .26 [6.60]
1.81 [46.05]
2.02 [51.33]
.55 [14.00]
2.05 [52.10]
2.02 [51.33]
1.63 [41.35]
1.56 [39.65]
.75 [19.05]
2.36 [59.94]
1.74 [44.17]
2.31 [58.75]
3.74 [94.87]
Ø2.90[Ø73.66]
1/2" PARBOND 3/4" PARBOND
1/2" FNPT 3/4" PARFLARE
1/2" PARFLARE
OUT OUT
OUT OUT
IN
AIR
TEST
Parker Hannifi n CorporationPartek OperationTucson, AZ
42
FeaturesOne piece precision
machined diaphragms
manufactured from
the latest technology
modifi ed PTFE. Provides
over fi ve times the
fl exural life as compared
to conventional PTFE.
Tongue and groove
seat and diaphragm for
positive through fl ow
shut off and diaphragm
to body seal.
PVDF coated stainless
steel springs.
Submergible option
isolates all valve
components from the
external environment.
Multi-position mounting
base.
Benefi tsHigh cycle life.
Lower replacement
costs.
Less downtime.
Reduces effects of
corrosive environments.
Valve remains functional
while operating in wet
or gaseous corrosive
environments.
Allows for more
mounting fl exibility
and connector fi tting
reduction.
Specifi cationsMaterials of ConstructionWetted: PFA, Modifi ed PTFE
Non-wetted: PFA, PVDF, Viton seals, PTFE coated SS springs
Pressure RangesCOM to NO: 27” HG vacuum (913 mbar) to 80 PSIG (5.5 bar)
NO to COM: 27” HG vacuum (913 mbar) to 80 PSIG (5.5 bar)
COM to NC: 27” HG vaccum (913 mbar) to 80 PSIG (5.5 bar)
with 20 PSIG (1.4 bar) maximum back pressure
NC to COM: 27” HG vacuum (913 mbar) to 80 PSIG (5.5 bar)
with 50 PSIG (3.4 bar) maximum back pressure
Actuator: 60 PSIG (4.2 bar) to 100 PSIG (7 bar)
Pressure ranges for operation at ambient temperatures. For use
at higher temperatures consult Pressure/Temperature chart on
page 3.
Temperature RangesAmbient: 0° - 150° F (-17° - 66° C)
Fluid: 0° - 266° F (-17° - 130° C)
Product OverviewThe PV-11 PFA 3 Way Diaphragm Valve is designed for use
in high purity semiconductor applications. It is also ideally
suited for ultra-pure water and aggressive chemical or gas
applications. The design utilizes a molded high purity PFA
body with precision machined areas. One piece machined
modifi ed PTFE diaphragms are also utilized for excellent
fl exibility and life. A full 1/2” orifi ce provides maximum fl ow
capability in a compact package.
PV-11 1/2” Pneumatic 3 Way Valve
Parker Hannifi n CorporationPartek OperationTucson, AZ
43
.57 [14.40]
NO
2.01 [50.93]
3/4" PARFLARE
1/2" FNPT
NO
2.88 [73.03]
2.06 [52.25]
1/2" PARBOND
2.06 [52.25]
NO
3/4" PARBOND
NCNC NONO
2.56 [65.10]
3.18 [80.87]
Ø1.636 [41.55]
Ø 2.93[74.42]
4.54 [115.42]
[46.20]
1.28 [32.47]
1/2" PARFLARE
*MOUNTING RING
2X Ø .26[6.60]
1.58 [40.18]
AIR PORT CONNECTION, 1/8” FNPTTEST PORT CONNECTIONS, 1/4-28 UNF
BRACKETED DIMENSIONSARE IN mm.
PV-11 1/2” Pneumatic 3 Way Valve
rebmuNledoM vC vK noitarugifnoCwolF noitarugifnoCtroP
120-11-VP 9.1 1.72
YAW3
eralfraP"2/1220-11-VP 8.2 0.04 eralfraP"4/3320-11-VP 8.2 0.04 dnobraP"2/1420-11-VP 8.2 0.04 dnobraP"4/3520-11-VP 8.2 0.04 TPNF"2/1
Parfl are models are supplied with PVDF nuts. For PFA nuts add -T to model number.
*To order part without mounting ring add -01 to model number.
PRESSURE DROP VS. FLOW RATEFLOW RATE (lpm)
FLOW RATE (gpm)
DE
LTA
-P (
psi
)
DE
LTA
-P (
bar
)
0 5
4
10
8
15
12
20
16
25
20
30
24
.28
.56
.84
1.12
1.40
1.6519 38 57 76 95 113
1/2" ParfareAll Other Configurations
Parker Hannifi n CorporationPartek OperationTucson, AZ
44
FeaturesPrecision machined
diaphragm
manufactured from
the latest technology
modifi ed PTFE.
Provides over fi ve
times the fl exural
life as compared to
conventional PTFE.
Tongue and groove
seat and diaphragm for
positive through fl ow
shut off and diaphragm
to body seal.
PVDF coated stainless
steel spring.
Bypass integral to valve
body to prevent stagna-
tion of ultra-pure water.
Modifi ed fl ow
confi gurations
with numerous end
connections including
Parfl are available.
Benefi tsHigh cycle life.
Lower replacement
costs.
Less downtime.
Reduces effects of
corrosive environment.
Prevents contamination
of media.
Reduces connections,
mounting space, and
overall cost.
Specifi cationsMaterials of ConstructionWetted: PFA, Modifi ed PTFE
Non-wetted: PFA, PVDF, Viton seals, PTFE coated SS springs
Pressure RangesForward: 27” HG vaccum (913 mbar) to 80 PSIG (5.5 bar)
with 20 PSIG (1.4 bar) maximum back pressure
Backward: 27” HG vacuum (913 mbar) to 80 PSIG (5.5 bar)
with 50 PSIG (3.4 bar) maximum back pressure
Actuator: 60 PSIG (4.2 bar) to 100 PSIG (7 bar)
Pressure ranges for operation at ambient temperatures. For
use at higher temperatures consult Pressure/Temperature chart
on page 3.
Temperature RangesAmbient: 0° - 150° F (-17° - 66° C)
Fluid: 0° - 266° F (-17° - 130° C)
Product OverviewThe PV-11 Adjustable Bypass Valve is designed for use in
ultra-pure water applications. The design utilizes a molded
high purity PFA body with precision machined seats. A
machined modifi ed PTFE diaphragm is also utilized for
excellent fl exibility and life. The integral bypass valve
prevents the stagnation and deadheading of media in an
ultra-pure water system.
PV-11 1/2” Pneumatic Adjustable Bypass Valve
Parker Hannifi n CorporationPartek OperationTucson, AZ
45
.57 [14.40]
NO
2.01 [50.93]
1/2" FNPT
3/4" PARFLARE
1.65 MAX.[41.97]
OUTLET
NONC
1.58 [40.18]
Ø1.636 [41.55]
INLET
3.18 [80.87]
2.56 [65.10]
1/2" PARFLARE
MOUNTING DETAIL
DVP
/F
1
AR
LPA
RF
" 2
E
4.54 [115.42]
1.82 [46.20]
1.28 [32.47]
2.88 [73.03]
2X Ø .26[Ø 6.60]
Ø 2.93[Ø 74.42]
AIR PORT CONNECTION, 1/8” FNPTTEST PORT CONNECTIONS, 1/4-28 UNF
BRACKETED DIMENSIONSARE IN mm.
PV-11 1/2” Pneumatic Adustable Bypass Valve
rebmuNledoM vC vK noitarugifnoCwolF noitarugifnoCtroP
103-11-VP 9.1 1.72CN
eralfraP"2/1203-11-VP 8.2 0.04 eralfraP"4/3503-11-VP 8.2 0.04 TPNF"2/1
Parfl are models are supplied with PVDF nuts. For PFA nuts add -T to model number.
PRESSURE DROP VS. FLOW RATEFLOW RATE (lpm)
FLOW RATE (gpm)
DE
LTA
-P (
psi
)
DE
LTA
-P (
bar
)
0 5
4
10
8
15
12
20
16
25
20
30
24
.28
.56
.84
1.12
1.40
1.6519 38 57 76 95 113
1/2" ParfareAll Other Configurations
Cv / Kv vs. TURNS FOR BYPASS PORT
TURNS
Cv
Kv
0 0.6
.02
1.2
.04
1.8
.06
2.4
.08
3.0
.10
3.6
.12
.29
.57
.86
1.14
1.43
1.71
All Configurations
Parker Hannifi n CorporationPartek OperationTucson, AZ
46
FeaturesOne piece precision
machined diaphragm
manufactured from
the latest technology
modifi ed PTFE. Provides
over fi ve times the
fl exural life as compared
to conventional PTFE.
Tongue and groove
seat and diaphragm for
positive through fl ow
shut off and diaphragm
to body seal.
PVDF coated stainless
steel spring.
Submergible option
isolates all valve
components from the
external environment.
Benefi tsHigh cycle life.
Lower replacement
costs.
Less downtime.
Reduces effects of
corrosive environments.
Valve remains functional
while operating in wet
or gaseous corrosive
environments.
Specifi cationsMaterials of ConstructionWetted: PFA, Modifi ed PTFE
Non-wetted: PFA, PVDF, Viton seals, PTFE coated SS springs
Pressure RangesForward: 27” HG vaccum (913 mbar) to 100 PSIG (7 bar)
Backward: 80 PSIG (5.5 bar) with 100 PSIG (3.4 bar) inlet pressure
100 PSIG (7 bar) with 60 PSIG (4.2 bar) inlet pressure
Actuator: 60 PSIG (4.2 bar) to 100 PSIG (7 bar)
Pressure ranges for operation at ambient temperatures. For use
at higher temperatures consult Pressure/Temperature chart on
page 3.
Temperature RangesAmbient: 0° - 150° F (-17° - 66° C)
Fluid: 0° - 266° F (-17° - 130° C)
Normally Closed shown
Product OverviewThe PV-12 Diaphragm Valve is designed for use in high
purity semiconductor applications, and is also ideally suited
for ultra-pure water and aggressive chemical or gas appli-
cations. The design utilizes a molded high purity PFA body
with precision machined seat and diaphragm sealing areas.
A one piece machined modifi ed PTFE diaphragm is also
utilized for excellent fl exibility and life. A full 1” orifi ce pro-
vides maximum fl ow capability in a compact package.
PV-12 1” Pneumatic 2 Way Valve
Parker Hannifi n CorporationPartek OperationTucson, AZ
47
1.07[27.23]
4.00 [101.70]
2.59 [65.86]
PARFLARE 1"
Ø4.22 [Ø107.19]
2X Ø.28 [Ø7.11]
3.75 [95.35]
1.88 [47.68]
1" PARBOND
4.28 [108.81]
2.56 [65.00]
5.78 [146.81]
.323 [82.04]
(N.O. ONLY)
2.32 [58.85]
PARBOND 3/4"
AIR AND TEST PORTCONNECTIONS, 1/8” FNPT
BRACKETED DIMENSIONSARE IN mm.
PV-12 1” Pneumatic 2 Way Valve
rebmuNledoM CV KV .gifnoCwolF .gifnoCtroP
100-21-VP 7.51 2.422
CN
dnobraP"1
200-21-VP 3.31 9.981 eralfraP"1
300-21-VP 6.9 8.241 dnobraP"4/3
rebmuNledoM CV KV .gifnoCwolF .gifnoCtroP
500-21-VP 7.51 2.422
ON
dnobraP"1
600-21-VP 3.31 9.981 eralfraP"1
700-21-VP 6.9 8.241 dnobraP"4/3
Parfl are models are supplied with PVDF nuts. For PFA nuts add -T to model number.
PRESSURE DROP VS. FLOW RATEFLOW RATE (lpm)
FLOW RATE (gpm)
DE
LTA
-P (
psi
)
DE
LTA
-P (
bar
)
0 10
10
20
20
30
30
40
40
50
50
60
60
.7
1.4
2.1
2.8
3.5
4.238 76 113 151 189 227
3/4" Parbond 1" Parflare1" Parbond
Parker Hannifi n CorporationPartek OperationTucson, AZ
48
Product OverviewThe PV-16 PFA diaphragm valve is designed for use in
high purity semiconductor applications, and is also ideally
suited for ultra-pure water and aggressive chemical or gas
applications. The design utilizes a molded high purity PFA
body with precision machined seat and diaphragm sealing
areas. A one piece machined modifi ed PTFE diaphragm
is also utilized for excellent fl exibility and life. A full 3/4”
orifi ce provides maximum fl ow capability in a compact
package.
PV-16 3/4” Pneumatic PFA 2 Way Valve
FeaturesOne piece precision
machined diaphragm
manufactured from
the latest technology
modifi ed PTFE. Provides
over fi ve times the
fl exural life as compared
to conventional PTFE.
Tongue and groove
seat and diaphragm for
positive through fl ow
shut off and diaphragm
to body seal.
Halar coated stainless
steel spring.
Benefi tsHigh cycle life.
Lower replacement
costs.
Less downtime.
Reduces effects of
corrosive environments.
Specifi cationsMaterials of ConstructionWetted: PFA, Modifi ed PTFE
Non-wetted: PVDF, Viton, PTFE coated SS spring
Pressure Ranges0 - 120 PSIG (8.3 bar) See Cracking Pressure Chart on next page.
Actuation: 60 PSIG (4.1 bar) - 120 PSIG (8.3 bar)
Pressure ranges for operation at ambient temperatures. For
use at higher temperatures consult Pressure/Temperature chart
on page 3.
Temperature RangesAmbient: 0° - 150° F (-17° - 66° C)
Fluid: 0° - 266° F (-17° - 130° C)
Parker Hannifi n CorporationPartek OperationTucson, AZ
49
Ø4.38 [Ø111.3 mm]
4X .28[7.1 mm]
Ø3.75 [Ø95.3 mm]
4X 75˚EQUALLYSPACED
2.73 [69.3 mm]
3.43 [87.1 mm]
1.70 [43.2 mm]
5.28 [134.0 mm]
A
AIR PORT CONNECTION, 1/8” FNPTTEST PORT CONNECTION, 1/4-28 UNF
BRACKETED DIMENSIONSARE IN mm.
Parfl are model numbers are supplied with PVDF nuts. Also available with PFA (-T) nuts.
*Ends are fused on.
PV-16 3/4” Pneumatic PFA 2 Way Valve
rebmuNledoM CV KV X-noitarugifnoCwolF noitarugifnoCtroP]mm[ninoisnemiD
A
216X-61-VP 8.5 7.28
CN=1ON=2
eralfraP"4/3 ]27.041[45.5
10-216X-61-VP 8.5 7.28 gnoLeralfraP"4/3 ]95.461[84.6
616X-61-VP 9.7 6.211 *eralfraP"1 ]56.132[21.9
217X-61-VP 9.7 6.211 dnobraP"4/3 ]68.941[09.5
CRACKING PRESSURE
PRESSURE TO INLET PORT (bar)
PRESSURE TO INLET PORT (psi)
PR
ES
SU
RE
TO
OU
TL
ET
PO
RT
(p
si)
PR
ES
SU
RE
TO
OU
TL
ET
PO
RT
(b
ar)
0 24
24
48
48
72
72
96
96
120
120
144
144
1.7
3.3
5.0
6.6
8.3
9.91.7 3.3 5.0 6.6 8.3 9.9
SPECIFIED SEALING AREA
PRESSURE DROP VS. FLOW RATE
FLOW RATE (lpm)
FLOW RATE (gpm)
DE
LTA
-P (
psi
)
DE
LTA
-P (
bar
)
0 10
10
20
20
30
30
40
40
50
50
60
60
.7
1.4
2.1
2.8
3.5
4.238 76 113 151 189 227
3/4" Parflare 3/4" Parbond, 1" Parflare
Parker Hannifi n CorporationPartek OperationTucson, AZ
50
Product OverviewThe PV-16 PFA diaphragm valve is designed for use in
high purity semiconductor applications, and is also ideally
suited for ultra-pure water and aggressive chemical or gas
applications. The design utilizes a molded high purity PFA
body with precision machined seat and diaphragm sealing
areas. A one piece machined modifi ed PTFE diaphragm
is also utilized for excellent fl exibility and life. A full 3/4”
orifi ce provides maximum fl ow capability in a compact
package.
PV-16 3/4” Pneumatic PFA 3 Way Valve
FeaturesOne piece precision
machined diaphragm
manufactured from
the latest technology
modifi ed PTFE. Provides
over fi ve times the
fl exural life as compared
to conventional PTFE.
Tongue and groove
seat and diaphragm for
positive through fl ow
shut off and diaphragm
to body seal.
Halar coated stainless
steel spring.
Benefi tsHigh cycle life.
Lower replacement
costs.
Less downtime.
Reduces effects of
corrosive environments.
Specifi cationsMaterials of ConstructionWetted: PFA, Modifi ed PTFE
Non-wetted: PVDF, Viton, PTFE coated SS spring
Pressure Ranges0 - 120 PSIG (8.3 bar) See Cracking Pressure Chart on next page.
Actuation: 60 PSIG (4.1 bar) - 120 PSIG (8.3 bar)
Pressure ranges for operation at ambient temperatures. For
use at higher temperatures consult Pressure/Temperature chart
on page 3.
Temperature RangesAmbient: 0° - 150° F (-17° - 66° C)
Fluid: 0° - 266° F (-17° - 130° C)
Parker Hannifi n CorporationPartek OperationTucson, AZ
51
5.53 [140.6 mm]
Ø4.38 [Ø111.3 mm]
Ø3.75 [Ø95.3 mm]
4X .28[7.1 mm]
4X 75˚EQUALLYSPACED
3.39 [86.2 mm]2.69
[68.4 mm]1.66
[42.2 mm]
AB
AIR PORT CONNECTION, 1/8” FNPTTEST PORT CONNECTION, 1/4-28 UNF
BRACKETED DIMENSIONSARE IN mm.
Parfl are model numbers are supplied with PVDF nuts. Also available with PFA (-T) nuts.
*Ends are fused on.
PV-16 3/4” Pneumatic PFA 3 Way Valve
rebmuNledoM CV KV noitarugifnoCwolF noitarugifnoCtroP
snoisnemiD
A B
2163-61-VP 4.5 0.77
YAW3
CNMOC
ON
eralfraP"4/3 ]mm27.041["45.5 ]mm73.17["18.2
10-2163-61-VP 4.5 0.77 gnoLeralfraP"4/3 ]mm95.461["84.6 ]mm73.17["18.2
6163-61-VP 3.7 1.401 *eralfraP"1 ]mm56.132["21.9 ]mm28.511["65.4
2173-61-VP 3.7 1.401 dnobraP"4/3 ]mm68.941["09.5 ]mm39.47["59.2
2164-61-VP 4.5 0.77
stroPdesreveRYAW3
ONMOC
CN
eralfraP"4/3 ]mm27.041["45.5 ]mm73.17["18.2
10-2164-61-VP 4.5 0.77 gnoLeralfraP"4/3 ]mm95.461["84.6 ]mm73.17["18.2
6164-61-VP 3.7 1.401 *eralfraP"1 ]mm56.132["21.9 ]mm28.511["65.4
2174-61-VP 3.7 1.401 dnobraP"4/3 ]mm68.941["09.5 ]mm39.47["59.2
CRACKING PRESSURE
PRESSURE TO INLET PORT (bar)
PRESSURE TO INLET PORT (psi)
PR
ES
SU
RE
TO
OU
TL
ET
PO
RT
(p
si)
PR
ES
SU
RE
TO
OU
TL
ET
PO
RT
(b
ar)
0 24
24
48
48
72
72
96
96
120
120
144
144
1.7
3.3
5.0
6.6
8.3
9.91.7 3.3 5.0 6.6 8.3 9.9
SPECIFIED SEALING AREA
PRESSURE DROP VS. FLOW RATE
FLOW RATE (lpm)
FLOW RATE (gpm)
DE
LTA
-P (
psi
)
DE
LTA
-P (
bar
)
0 10
10
20
20
30
30
40
40
50
50
60
60
.7
1.4
2.1
2.8
3.5
4.238 76 113 151 189 227
3/4" Parflare 3/4" Parbond, 1" Parflare
Parker Hannifi n CorporationPartek OperationTucson, AZ
52
Product OverviewThe PV-16 PFA sampling valve is designed for use in high
purity semiconductor applications, and is also ideally
suited for ultra-pure water and aggressive chemical or
gas applications. The design utilizes a molded high purity
PFA body with precision machined seat and diaphragm
sealing areas. A one piece machined modifi ed PTFE dia-
phragm is also utilized for excellent fl exibility and life. The
valve incorporates a full fl ow through port with a low dead
volume down leg.
PV-16 3/4” Pneumatic PFA Sampling Valve
FeaturesOne piece precision
machined diaphragm
manufactured from
the latest technology
modifi ed PTFE. Provides
over fi ve times the
fl exural life as compared
to conventional PTFE.
Halar coated stainless
steel spring.
Full fl ow through port.
Benefi tsHigh cycle life.
Lower replacement
costs.
Less downtime.
Reduces effects of
corrosive environments.
Reduced pressure drop.
Specifi cationsMaterials of ConstructionWetted: PFA, Modifi ed PTFE
Non-wetted: PVDF, Viton, PTFE coated SS spring
Pressure Ranges0 - 120 PSIG (8.3 bar) See Cracking Pressure Chart on next page.
Actuation: 60 PSIG (4.1 bar) - 120 PSIG (8.3 bar)
Pressure ranges for operation at ambient temperatures. For
use at higher temperatures consult Pressure/Temperature chart
on page 3.
Temperature RangesAmbient: 0° - 150° F (-17° - 66° C)
Fluid: 0° - 266° F (-17° - 130° C)
Parker Hannifi n CorporationPartek OperationTucson, AZ
53
2.73 [69.3 mm]
3.43 [87.1 mm]
Ø4.38 [Ø111.3 mm]
1.70 [43.2 mm]
5.28 [134.0 mm]
4X 75˚EQUALLYSPACED
4X .28[7.1 mm]
Ø3.75 [Ø95.3 mm]
AB
AIR PORT CONNECTION, 1/8” FNPTTEST PORT CONNECTION, 1/4-28 UNF
BRACKETED DIMENSIONSARE IN mm.
Parfl are model numbers are supplied with PVDF nuts. Also available with PFA (-T) nuts.
PV-16 3/4” Pneumatic PFA Sampling Valve
rebmuNledoM
troPhguorhT troPelpmaS
troPhguorhT troPelpmaS
snoisnemiD
vC vK vC vK A B
806-2165-61-VP 0.31 4.581 3.2 8.23 eralfraP"4/3 eralfraP"2/1 ]mm27.041["45.5 ]mm38.86["17.2
216-2165-61-VP 0.31 4.581 6.4 6.56 eralfraP"4/3 eralfraP"4/3 ]mm27.041["45.5 ]mm73.17["18.2
217-2165-61-VP 0.31 4.581 9.6 7.89 eralfraP"4/3 dnobraP"4/3 ]mm27.041["45.5 ]mm39.47[59.2
806-2175-61-VP 2.52 29.953 3.2 8.23 dnobraP"4/3 eralfraP"2/1 ]mm68.941["09.5 ]mm38.86["17.2
216-2175-61-VP 2.52 29.953 6.4 6.56 dnobraP"4/3 eralfraP"4/3 ]mm68.941["09.5 ]mm73.17["18.2
217-2175-61-VP 2.52 29.953 9.6 7.89 dnobraP"4/3 dnobraP"4/3 ]mm68.941["09.5 ]mm39.47[59.2
CRACKING PRESSURE
PRESSURE TO INLET PORT (bar)
PRESSURE TO INLET PORT (psi)
PR
ES
SU
RE
TO
OU
TL
ET
PO
RT
(p
si)
PR
ES
SU
RE
TO
OU
TL
ET
PO
RT
(b
ar)
0 24
24
48
48
72
72
96
96
120
120
144
144
1.7
3.3
5.0
6.6
8.3
9.91.7 3.3 5.0 6.6 8.3 9.9
SPECIFIED SEALING AREA
Parker Hannifi n CorporationPartek OperationTucson, AZ
54
Product OverviewThe PV-20 distribution valve is designed for use in slurry
applications, and is also ideally suited for ultra-pure water
and aggressive chemical or gas applications. The design
utilizes a machined PTFE body with precision machined
seat and diaphragm sealing areas. The valve is offered in
3 orifi ce sizes (1/4”, 1/2” and 1”) and port sizes ranging
from 1/4” to 1 1/4”.
PV-20 1/4” - 1” Pneumatic PTFE Distribution Valve
FeaturesFully swept open bowl
diaphragm seat area.
Self draining design.
High load point seat seal.
Angled and rounded internal
fl ow path.
One piece precision
machined diaphragm
manufactured from modifi ed
PTFE.
Evenly distributed seat
sealing forces.
Maximized diaphragm
thickness.
Benefi tsMinimizes fl uid shear and
smooth fl ow transition.
Minimizes area for
entrapment and stagnation
of media.
Improves sealing
mechanism for aggressive
chemicals, deionized water
and abrasive slurry media.
Minimizes particle
contribution of valve.
Provides faster purging and
cleaning of valve.
Less pressure drop
allows for lower pressure
requirements upstream.
Improves fl uid fl ow
dynamics.
Improves cycle life, less
shear than standard PTFE
material, lower replacement
costs, less downtime.
Minimized diaphragm and
valve seat strain.
Stabilizes valve back
pressure capability.
Minimizes potential
for permeation while
maximizing cycle life.
Specifi cationsMaterials of ConstructionWetted: PTFE, Modifi ed PTFE
Non-wetted: PVDF, Viton, PTFE coated SS spring
Pressure Ranges1/4” Orifi ce: 27” HG vacuum (913 mbar) - 80 PSIG (5.5 bar)
1/2” Orifi ce: 27” HG vacuum (913 mbar) - 100 PSIG (7 bar)
1” Orifi ce: 27” HG vacuum (913 mbar) - 100 PSIG (7 bar)
Actuation: 60 PSIG (4.1 bar) - 80 PSIG (5.5 bar)
Pressure ranges for operation at ambient temperatures. For
use at higher temperatures consult Pressure/Temperature chart
on page 3.
Temperature RangesAmbient: 0° - 150° F (-17° - 66° C)
Fluid: 0° - 266° F (-17° - 130° C)
Parker Hannifi n CorporationPartek OperationTucson, AZ
55
Parfl are models are supplied with PVDF nuts. For PFA nuts add -T to model number. Contact factory for Pillar end connections.
PV-20 1/4” - 1” Pneumatic PTFE Distribution Valve
C
A
H
G
1/4” ORIFICE: 10-32 UNF-2B ACTUATION PORT1/2” ORIFICE: 1/8“ FNPT ACTUATION PORT 1” ORIFICE: 1/8“ FNPT ACTUATION PORT
1/4” ORIFICE: 2X Ø.17 THRU, C.B. Ø.28 X .401/2” ORIFICE: 2X Ø.19 THRU, C.B. Ø.31 X .50
1” ORIFICE: 2X Ø.28 THRU, C.B. Ø.44 X 1.00
B
1/4-28 UNF LEAK DETECTION PORT
F
E
D
PRESSURE DROP VS. FLOW RATE
FLOW RATE (lpm)
FLOW RATE (gpm)
DE
LTA
-P (
psi)
DE
LTA
-P (
ba
r)
0 10
10
20
20
30
30
40
40
50
50
60
60
.7
1.4
2.1
2.8
3.5
4.2
38 76 113 151 189 227
PV
-20-0
8-X
608-R
PV-2
0-0
8-X
612-R
PV-2
0-1
6-X
612
PV-20-1
6-X616
PV-20-16-X620
FLOW RATE (lpm)
FLOW RATE (gpm)
DE
LTA
-P (
psi)
DE
LTA
-P (
ba
r)
0 1
5
2
10
3
15
4
20
5
25
6
30
.34
.69
1.0
1.4
1.7
2.1
3.8 7.6 11.3 15.1 18.9 22.7
PV
-20-0
4-X
604
PV-2
0-0
4-X
606
Part Number Cv KvBody
Size
Valve
Type
Port
Confi guration
A B C D E F G H
inch mm inch mm inch mm inch mm inch mm inch mm inch mm inch mm
PV-20-04-1604 .20 2.8 1/4”
NC
1/4” Parfl are .18 4.57 .55 13.97 3.80 96.52 1.50 38.10 1.15 29.21 2.28 57.91 1.25 31.75 .50 12.70
PV-20-04-1606 .76 10.8 1/4” 3/8” Parfl are .18 4.57 .55 13.97 3.96 100.58 1.50 38.10 1.15 29.21 2.28 57.91 1.25 31.75 .50 12.70
PV-20-08-1608-R 2.4 34.2 1/2” 1/2” Parfl are .25 6.35 1.44 36.58 5.20 132.08 2.50 63.50 1.80 45.72 4.14 105.16 2.00 50.80 .78 19.81
PV-20-08-1612-R 3.9 55.8 1/2” 3/4” Parfl are .25 6.35 1.44 36.58 5.35 135.89 2.50 63.50 2.00 50.80 4.34 110.24 2.00 50.80 .83 20.96
PV-20-16-1612 6.4 91.5 1” 3/4” Parfl are .28 7.11 1.50 38.10 6.22 157.99 3.38 85.85 2.88 73.15 6.08 154.43 3.00 76.20 1.00 25.40
PV-20-16-1616 10.9 155.4 1” 1” Parfare .28 7.11 1.50 38.10 6.98 177.29 3.38 85.85 2.88 73.15 6.08 154.43 3.00 76.20 1.00 25.40
PV-20-16-1620 13.5 192.9 1” 1 1/4” Parfl are .28 7.11 1.50 38.10 8.07 204.98 3.75 95.25 3.25 82.55 6.45 163.83 3.00 76.20 1.25 31.75
PV-20-04-2604 .20 2.8 1/4”
NO
1/4” Parfl are .18 4.57 .55 13.97 3.80 96.52 1.50 38.10 1.15 29.21 2.28 57.91 1.25 31.75 .50 12.70
PV-20-04-2606 .76 10.8 1/4” 3/8” Parfl are .18 4.57 .55 13.97 3.96 100.58 1.50 38.10 1.15 29.21 2.28 57.91 1.25 31.75 .50 12.70
PV-20-08-2608-R 2.4 34.2 1/2” 1/2” Parfl are .25 6.35 1.44 36.58 5.20 132.08 2.50 63.50 1.80 45.72 4.14 105.16 2.00 50.80 .78 19.81
PV-20-08-2612-R 3.9 55.8 1/2” 3/4” Parfl are .25 6.35 1.44 36.58 5.35 135.89 2.50 63.50 2.00 50.80 4.34 110.24 2.00 50.80 .83 20.96
PV-20-16-2612 6.4 91.5 1” 3/4” Parfl are .28 7.11 1.50 38.10 6.22 157.99 3.38 85.85 2.88 73.15 6.08 154.43 3.00 76.20 1.00 25.40
PV-20-16-2616 10.9 155.4 1” 1” Parfare .28 7.11 1.50 38.10 6.98 177.29 3.38 85.85 2.88 73.15 6.08 154.43 3.00 76.20 1.00 25.40
PV-20-16-2620 13.5 192.9 1” 1 1/4” Parfl are .28 7.11 1.50 38.10 8.07 204.98 3.75 95.25 3.25 82.55 6.45 163.83 3.00 76.20 1.25 31.75
Parker Hannifi n CorporationPartek OperationTucson, AZ
56
FeaturesPolished sealing
surfaces.
Tongue and groove
external seal.
Machined PTFE spring.
Numerous end confi gura-
tions available including
Parflare. Available with
different confi gurations
on either end.
Benefi tsLong life and superior
sealing characteristics.
Eliminates o-rings and
compatibility problems.
Low cracking pressure.
Reduces connections,
mounting space, and
overall cost.
Specifi cationsMaterials of ConstructionWetted: PTFE
Non-wetted: PFA, PVDF, ETFE
Cracking Pressure0.25 PSIG (.017 bar) - 0.75 PSIG (.052 bar)
Back Check Sealing Pressure5.0 PSIG (.35 bar)
Pressure Range27” Hg vacuum (913 mbar) - 120 PSIG (8.3 bar)
Pressure ranges for operation at ambient temperatures. For
use at higher temperatures consult Pressure/Temperature chart
on page 3.
Temperature RangesStyle 1: 32° - 212° F (0° - 100° C) Ambient
32° - 266° F (0° - 130° C) Fluid
Style 2 & 3: 50° - 212° F (10° - 100° C) Ambient
50° - 266° F (10° - 130° C) Fluid
Style 4 & 5: 60° - 212° F (15° - 100° C) Ambient
60° - 266° F (15° - 130° C) Fluid
Product OverviewThe CV-1 PTFE Check Valve is designed for use in high
purity semiconductor applications, and is also ideally suited
for ultra-pure water and aggressive chemical or gas appli-
cations. The design utilizes machined PTFE components
to provide superior chemical resistance and purity without
requiring o-rings for sealing. The machined PTFE spring
allows for low cracking pressure operation and minimal
back pressure for resealing.
CV-1 Check Valve
Parker Hannifi n CorporationPartek OperationTucson, AZ
57
.75 [19.05]
.38 [9.65]
1/8" FNPT1/4" FNPT
1.13 [28.70]
1/4" PARGRIP 1/8" PARGRIP
3/8" FNPT
1.33 [33.76]
1/2" PARGRIP
.50 [12.70]
.50 [12.70]
1.15 [29.21]
STYLE 1
1.52 [38.61]
AR
PLFAR
1.23 [31.24]
3/8" PARFLARE
STYLE 2
1.43 [36.37]
1.35 [34.29]
PV
F/ 1
D
VP
D
LA
RF
ERP
"
A
1/2" PARFLARE
2
E
1/4" PARFLARE
F 1/4"
Ø1.48 [37.59]
Ø1.23 [31.24]
1.12 [28.45]
3/8" PARGRIP
Ø1.86 [47.24]
1/2" FNPT
STYLE 3
1.23 [31.24]
STYLE 4
2.16 [54.81]
Ø2.75 [69.85]
Ø3.25 [82.55]STYLE 5
3.27 [83.06]
3/4"
VP
DF
A
FL
RE
PR
A
3/4" PARFLARE
1.80 [45.72]
P
EAL
R
APR
1"F
FDV
1" PARFLARE
1" FNPT
.78 [19.81]
1.46 [37.08]
.63[16.00]
CV-1 Check Valve
Pargrip models are supplied with PFA nuts. Parfl are models are supplied with PVDF nuts. For PFA nuts add -T to model number.
BRACKETED DIMENSIONS ARE IN mm.
rebmuNledoM CV KV elytS noitarugifnoCtroP
2211-1-VC 16.0 87.8 1 TPNF"8/14411-1-VC 15.1 47.12 1 TPNF"4/16611-1-VC 34.2 00.53 2 TPNF"8/38811-1-VC 22.4 77.06 3 TPNF"2/1616111-1-VC 00.41 6.102 5 TPNF"1
2222-1-VC 20.0 92.0 1 pirgraP"8/14422-1-VC 43.0 09.4 1 pirgraP"4/16622-1-VC 89. 11.41 1 pirgraP"8/38822-1-VC 71.2 52.13 2 pirgraP"2/14466-1-VC 62. 47.3 1 eralfraP"4/16666-1-VC 11.1 48.51 1 eralfraP"8/38866-1-VC 30.2 32.92 2 eralfraP"2/1212166-1-VC 31.4 74.95 3 eralfraP"4/3616166-1-VC 58.11 6.071 4 eralfraP"1
Parker Hannifi n CorporationPartek OperationTucson, AZ
58
Benefi tsHigh cycle life.
Lower replacement
costs.
Less downtime.
Isolates media from
adjusting screw.
Prevent over
pressurization in critical
applications.
FeaturesOne piece precision
machined diaphragm
poppet manufactured
from the latest
technology modifi ed
PTFE.
Provides over fi ve
times the fl exural
life as compared to
conventional PTFE.
Tongue and groove seat
and diaphragm poppet
for positive through fl ow
shut off and diaphragm
to body seal.
Field adjustable relief
pressure.
Product OverviewThe RV Relief Valve is designed for use in high purity
semiconductor applications, and is also ideally suited for
ultra-pure water and aggressive chemicals. The design
utilizes a molded PFA body with precision-machined
PTFE seats and diaphragm poppet. When a fi eld set relief
pressure is reached, the valve opens and permits fl ow. The
valve resets when 25% of original setpoint is reached.
Specifi cationsMaterials of ConstructionWetted: PFA, Modifi ed PTFE
Non-wetted: PVDF, SS, Brass, ABS, HDPE
Pressure Ranges15 PSIG (1.03 bar) - 120 PSIG (8.3 bar)
Pressure ranges for operation at ambient temperatures. For
use at higher temperatures consult Pressure/Temperature chart
on page 3.
Temperature RangesAmbient: 0° - 150° F (-17° - 66° C)
Fluid: 0° - 266° F (-17° - 130° C)
RV Relief Valve
Note: The RV Series Relief Valves should only be used to protect
Article 3, Paragraph 3 category equipment as defi ned in Pressure
Equipment Directive 97/23/EC Dated 29, May 1997.
Parker Hannifi n CorporationPartek OperationTucson, AZ
59
BRACKETED DIMENSIONSARE IN mm.
RV Relief Valve
1.20 [30.36]
.92 [23.34]
1.15 [29.21]
.40 [10.16]
1/4" PARFLARE.40
[10.16]
.40 [10.16]
.40 [10.16] SCREW
1.23 [31.24]
3/8" PARFLARE 1/4" FNPT
.56 [14.22]
3.37 [85.60]
rebmuNledoM vC vK noitarugifnoCwolF noitarugifnoCtroP XX-egnaRerusserPgniveileR
XX-441-VR 87. 3.11
FFO/NO
TPNF"4/1GISP06ot51-10GISP021ot06-20XX-426-VR 42. 5.3 eralfraP"4/1
XX-646-VR 07. 2.01 eralfraP"8/3
Parfl are model numbers are supplied with PVDF nuts. Also available with PFA (-T) nuts.
Parker Hannifi n CorporationPartek OperationTucson, AZ
60
SV-2 1/4” Solenoid Valve
Product OverviewThe SV-2 Solenoid Valve is designed for use in high purity
semiconductor applications, and is also ideally suited for
ultra-pure water and aggressive chemicals. The design
utilizes a molded high purity PFA body with precision
machined areas. A one-piece machined modifi ed PTFE
diaphragm is also utilized for excellent fl exibility and long
life. The valve is offered in 2 and 3 way confi gurations, in
3 orifi ce sizes, and in 2 standard voltages.
FeaturesOne piece precision
machined diaphragm
manufactured from
the latest technology
modifi ed PTFE.
Provides over fi ve
times the fl exural
life as compared to
conventional PTFE.
Tongue and groove
seat and diaphragm for
positive through fl ow
shut off and diaphragm
to body seal.
Benefi tsHigh cycle life.
Lower replacement
costs.
Less downtime.
Isolates media from
solenoid.
Specifi cationsMaterials of ConstructionWetted: PFA, Modifi ed PTFE
Non-wetted: Coated Aluminum, Plated Steel, SS, PFA, PVDF, Titanate
Pressure RangesForward: 0 - 80 PSIG (5.5 bar)
Pressure ranges for operation at ambient temperatures. For
use at higher temperatures consult Pressure/Temperature chart
on page 3.
Temperature RangesAmbient: -60° - 212° F (-51° - 100° C)
Fluid: -60° - 400° F (-51° - 204° C)
Solenoid Ratings24 VDC, 115 VAC (Double Wire)
All models rated at 9 watts at 68°F (20°C)
Coil Duty Cycle: 100%, however, 100% continuous duty may
affect performance of valve, therefore 50% continuous duty is
recommended.
OrientationAll models must be mounted vertically as indicated by the label
on the product.
Parker Hannifi n CorporationPartek OperationTucson, AZ
61
SV-2 1/4” Solenoid ValveBRACKETED DIMENSIONS
ARE IN mm.
OU
TNIINO
COM
NC
.87 [22.14]
1.25 C/L
.40 [10.16]
.57 [14.35]
Ø1.65
SCREW
.40 [10.16]
.40 [10.16]
[31.75]Ø
1.24 [31.51]
3.97 [100.93]
.40 [10.16]
1/4" FNPT
3-WAY VALVE 2-WAY VALVE
rebmuNledoM CV KV noitarugifnoCwolF eziSecifirO noitarugifnoCtroP X-egatloVdioneloS
X-4411-2-VS 06. 6.8 CN 052. TPNF"4/1CDV42=2CAV511=7
X-4421-2-VS 06. 6.8 ON 052. TPNF"4/1X-4431-2-VS 06. 6.8 YAW3 052. TPNF"4/1
DE
LTA
-P (
psi
)
0
25
5
20
15
10
DE
LTA
-P (
bar
)
1.72
1.38
1.03
.69
.34
FLOW RATE (lpm)PRESSURE DROP VS. FLOW RATE
1.9 3.8 5.7 7.6 11.39.5
FLOW RATE (gpm)0.5 1.0 1.5 2.0 3.02.5
All Configurations
Parker Hannifi n CorporationPartek OperationTucson, AZ
62
1. Terms and Conditions of Sale: All descriptions, quotations, proposals, offers, acknowledgments, acceptances and sales of Seller’s products are subject to and shall be governed exclusively by the terms and condi-tions stated herein. Buyer’s acceptance of any offer to sell is limited to these terms and conditions. Any terms or conditions in addition to, or inconsistent with those stated herein, proposed by Buyer in any accep-tance of an offer by Seller, are hereby objected to. No such additional, different or inconsistent terms and conditions shall become part of the contract between Buyer and Seller unless expressly accepted in writ-ing by Seller. Seller’s acceptance of any offer to purchase by Buyer is expressly conditional upon Buyer’s assent to all the terms and conditions stated herein, including any terms in addition to, or inconsistent with those contained in Buyer’s offer, Acceptance of Seller’s products shall in all events constitute such assent.2. Payment: Payment shall be made by Buyer net 30 days from the date of delivery of the items purchased hereunder. Amounts not timely paid shall bear interest at the maximum rate permitted by law for each month or portion thereof that the Buyer is late in making payment. Any claims by Buyer for omissions or shortages in a shipment shall be waived un-less Seller receives notice thereof within 30 days after Buyer’s receipt of the shipment.3. Delivery: Unless otherwise provided on the face hereof, delivery shall be made F.O.B. Seller’s plant. Regardless of the method of delivery, however, risk of loss shall pass to Buyer upon Seller’s delivery to a carrier. Any delivery dates shown are approximate only and Seller shall have no liability for any delays in delivery.4. Warranty: Seller warrants that the items sold hereunder shall be free from defects in material or workmanship for a period of 18 months from date of shipment from Parker Hannifi n Corporation. THIS WARRANTY COMPRISES THE SOLE AND ENTIRE WARRANTY PERTAINING TO ITEMS PROVIDED HEREUNDER. SELLER MAKES NO OTHER WAR-RANTY, GUARANTEE, OR REPRESENTATION OF ANY KIND WHAT-SOEVER. ALL OTHER WARRANTIES, INCLUDING BUT NOT LIMITED TO, MERCHANTABILITY AND FITNESS FOR PURPOSE, WHETHER EXPRESS, IMPLIED, OR ARISING BY OPERATION OF LAW, TRADE USAGE, OR COURSE OF DEALING ARE HEREBY DISCLAIMED.NOTWITHSTANDING THE FOREGOING, THERE ARE NO WARRAN-TIES WHATSOEVER ON ITEMS BUILT OR ACQUIRED WHOLLY OR PARTIALLY, TO BUYER’S DESIGNS OR SPECIFICATIONS.5. Limitation Of Remedy: SELLER’S LIABILITY ARISING FROM OR IN ANY WAY CONNECTED WITH THE ITEMS SOLD OR THIS CONTRACT SHALL BE LIMITED EXCLUSIVELY TO REPAIR OR REPLACEMENT OF THE ITEMS SOLD OR REFUND OF THE PURCHASE PRICE PAID BY BUYER, AT SELLER’S SOLE OPTION. IN NO EVENT SHALL SELLER BE LIABLE FOR ANY INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES OF ANY KIND OR NATURE WHATSOEVER, INC.LUDING BUT NOT LIMITED TO LOST PROFITS ARISING FROM OR IN ANY WAY CONNECTED WITH THIS AGREEMENT OR ITEMS SOLD HEREUNDER, WHETHER ALLEGED TO ARISE FROM BREACH OF CONTRACT, EXPRESS OR IMPLIED WARRANTY, OR IN TORT, IN-CLUDING WITHOUT LIMITATION, NEGLIGENCE, FAILURE TO WARN OR STRICT LIABILITY.6. Changes, Reschedules and Cancellations: Buyer may request to modify the designs or specifi cations for the items sold hereunder as well as the quantities and delivery dates thereof, or may request to cancel all or part of this order, however, no such requested modifi cation or cancellation shall become part of the contract between Buyer and Seller unless accepted by Seller in a written amendment to this Agreement. Acceptance of any such requested modifi cation or cancellation shall be at Seller’s discretion, and shall be upon such terms and conditions as Seller may require.7. Special Tooling: A tooling charge may be imposed for any special tooling, including without limitation, dies, fi xtures, molds and patterns, acquired to manufacture items sold pursuant to this contract. Such special tooling shall be and remain Seller’s property notwithstanding payment of any charges by Buyer. In no event will Buyer acquire any interest in apparatus belonging to Seller which is utilized in the notwithstanding any charges paid by Buyer. Unless otherwise agreed, Seller shall have the right to alter, discard or otherwise dispose of any special tooling or other property in its sole discretion at any time.
8. Buyer’s Property: Any designs, tools, patterns, materials, drawings, confi dential information or equipment furnished by Buyer or any other items which become Buyer’s property, may be considered obsolete and may be destroyed by Seller after two (2) consecutive years have elapsed without Buyer placing an order for the items which are manufactured us-ing such property, Seller shall not be responsible for any loss or damage to such property while it is in Seller’s possession or control.9. Taxes: Unless otherwise indicated on the face hereof, all prices and charges are exclusive of excise, sales, use, property, occupational or like taxes which may be imposed by any taxing authority upon the manufacture, sale or delivery of the items sold hereunder. If any such taxes must be paid by Seller or if Seller is liable for the collection of such tax, the amount thereof shall be in addition to the amounts for the items sold. Buyer agrees to pay all such taxes or to reimburse Seller therefore upon receipt of its invoice. If Buyer claims exemption from any sales, use or other tax imposed by any taxing authority, Buyer shall save Seller harmless from and against any such tax, together with any interest or penalties thereon which may be assessed if the items are held to be taxable.10. Indemnity For Infringement of Intellectual Property Rights: Seller shall have no liability for infringement of any patents, trademarks, copyrights, trade dress, trade secrets or similar rights except as provided in this Part 10. Seller will defend and indemnify Buyer against allegations of infringement of U.S. Patents, U.S. Trademarks, copyrights, trade dress and trade secrets (hereinafter ‘Intellectual Property Rights’). Seller will defend at its expense and will pay the cost of any settlement or damages awarded in an action brought against Buyer based on an allegation that an item sold pursuant to this contract infringes the Intellectual Property Rights of a third party. Seller’s obligation to defend and indemnify Buyer is contingent on Buyer notifying Seller within ten (10) days after Buyer becomes aware of such allegations of infringement, and Seller having sole control over the defense of any allegations or actions including all negotiations for settlement or compromise. If an item sold hereunder is subject to a claim that it infringes the Intellectual Property Rights of a third party, Seller may, at its sole expense and option, procure for Buyer the right to continue using said item, replace or modify said item so as to make it noninfringing, or offer to accept return of said item and return the purchase price less a reasonable allowance for depreciation. Notwithstanding the foregoing, Seller shall have no liability for claims of infringement based on information provided by Buyer, or directed to items delivered hereunder for which the designs are specifi ed in whole or part by Buyer, or infringements resulting from the modifi cation, com-bination or use in a system of any item sold hereunder. The foregoing provisions of this Part 10 shall constitute Seller’s sole and exclusive liability and Buyer’s sole and exclusive remedy for infringement of Intel-lectual Property Rights.If a claim is based on information provided by Buyer or if the design for an item delivered hereunder is specifi ed in whole or in part by Buyer, Buyer shall defend and indemnify Seller for all costs, expenses or judgments resulting from any claim that such item infringes any patent, trademark, copyright, trade dress, trade secret or any similar right.11. Force Majeure: Seller does not assume the risk of and shall not be liable for delay or failure to perform any of Seller’s obligations by reason of circumstances beyond the reasonable control of Seller (hereinafter ‘Events of Force Majeure’). Events of Force Majeure shall include without limitation, accidents, acts of God, strikes or labor disputes, acts, laws, rules or regulations of any government or government agency, fi res, fl oods, delays or failures in delivery of carriers or suppliers, shortages of materials and any other cause beyond Seller’s control.12. Entire Agreement/Governing Law: The terms and conditions set forth herein, together with any amendments, modifi cations and any different terms or conditions expressly accepted by Seller in writing, shall constitute the entire Agreement concerning the items sold, and there are no oral or other representations or agreements which pertain thereto. This Agreement shall be governed in all respects by the law of the State of Ohio. No actions arising out of the sale of the items sold hereunder or this Agreement may be brought by either party more than two (2) years after the cause of action accrues. 9/91-P
The items described in this document and other documents or descriptions provided by Parker Hannifi n Corporation, its subsidiaries and its authorized distributors are hereby offered for sale at prices to be established by Parker Hannifi n Corporation, its subsidiaries and its authorized distributors. This offer and its acceptance by any customer (“Buyer”) shall be governed by all of the following Terms and Conditions. Buyer’s order for any such items, when communicated to Parker Hannifi n Corporation, its subsidiary or an authorized distributor (“Seller”) verbally or in writing, shall constitute acceptance of this offer.
Offer of Sale
Parker’s Charter
To be a leading worldwide manufacturer of compo-
nents and systems for the builders and users of durable
goods. More specifi cally, we will design, market and
manufacture products controlling motion, fl ow and pres-
sure. We will achieve profi table growth through premier
customer service.
Product Information
North American customers seeking product infor mation,
the location of a nearby distributor, or repair services will
receive prompt attention by calling the Parker Product
Information Center at our toll-free
number: 1-800-C-PARKER (1-800-272-7537). In
Europe, call 00800-C-PARKER-H (00800-2727-5374).
The Fluid Connectors Group designs, manu factures and mar-kets rigid and fl exible connec-tors, and associated products used in pneumatic and fl uid systems.
The Hydraulics Group designs, produces and markets a full spectrum of hy-raulic com ponents and systems to builders and users of industrial and mobile machinery and equipment.
The Automation Group is a leading supplier of pneu-matic and electro mechanical components and systems to automation customers world-wide.
The Seal Group designs, manu-factures and distributes indus-trial and commercial sealing devices and related products by providing superior quality and total customer satisfaction.
The Filtration Group designs, manufactures and markets quality fi ltration and clarifi cation products, providing customers with the best value, quality, technical support, and global availability.
The Instrumentation Group is a global leader in the design, manufacture and distribution of high-quality critical fl ow com-ponents for worldwide process instrumentation, ultra-high-purity, medical and analytical applications.
About Parker Hannifi n Corporation
Parker Hannifi n is a leading global motion-control
company dedicated to delivering premier customer
service. A Fortune 500 corporation listed on the New
York Stock Exchange (PH), our components and sys-
tems comprise over 1,400 product lines that control
motion in some 1,000 industrial and aerospace mar-kets.
Parker is the only manufacturer to offer its customers a
choice of hydraulic, pneumatic, and electro mechan ical
motion-control solutions. Our Company has the largest
distribution network in its fi eld, with over 7,500 distribu-
tors serving nearly 400,000 customers worldwide.
Parker Hannifi n Corporation6035 Parkland Blvd.Cleveland, Ohio 44124-4141Telephone: (216) 896-3000Fax: (216) 896-4000www.parker.com
Parker Hannifi n Corporation
The Aerospace Group is a leader in the development, de-sign, manufacture and servicing of control systems and compo-nents for aerospace and related high- technology markets, while achieving growth through pre-mier customer service.
The Climate & Industrial Con-trols Group designs, manufac-tures and markets system-con-trol and fl uid-handling components and sys-tems to refrigeration, air-condi-tioning and industrial customers worldwide.
Parker Hannifi n CorporationVerifl o Division
Partek Operation
7075 East Southpoint RoadTucson, AZ 85706phone 520 574 2600fax 520 574 2700www.parker.com
© 2008 Parker Hannifi n Corporation