CX600 (MS-1682) Assembly Guide
■ 1、LCD MODULE ASSY
■ 2、UPPER CASE ASSY
■ 3、LOWER CASE ASSY
■ 4、ASSEMBLE UPPER CASE AND LOWER CASE
■ 5、KEYBOARD
■ 6、THERMAL-KIT、CPU、DRAM AND WLAN MODULE
■ 7、ODD MODULE
■ 8、HDD MODULE
■ 9、BOTTOM DOOR ASSY
■ 10、BATTERY PACK
CX600(MS-1682)Assembly Guide
1、 LCD MODULE ASSY
1.1:Assemble the MIC Module as left picture show
Component P/N Qty
MIC Module S34-2100910-K03 1
1.2:Assemble the WIRELESS L-Antenna board to
the LCD cover fixed position as left picture shows.
Component P/N Qty
L-Antenna S79-1800K80-J51 1
1.3:Assemble the WIRELESS R-Antenna board to
the LCD cover fixed position as left picture shows.
Component P/N Qty
R-Antenna S79-1800K70-J51 1
LCD Cover 307-682A211-Y31 1
CX600(MS-1682)Assembly Guide
1、 LCD MODULE ASSY
1.4:Assemble the 8 screws (M2*3mm)
Attention: the screw driver torque is 1.5-2.0Kgf-cm
Component P/N Qty
Display Module S1J-A42G002-S02 1
LCD BRACKET-L E2M-6810211-A89 1
LCD BRACKET-R E2M-6810111-A89 1
Screw E43-1203003-H29 8
1.5 Connect the Coaxial Cable(Camera Cable)
in the direction of the arrow in the picture;
1.6:Assemble CMOS Camera Module follow the
instruction as left picture shows.
Attention:Don’t assemble the CMOS Camera
Module with too strong force avoid damage the
module.
CX600(MS-1682)Assembly Guide
1、 LCD MODULE ASSY
1.7:Connect LVDS Cable to Display Module and
fix the cable with black tape;
Component P/N Qty
LVDS Cable K19-3028001-H39 1
1.8:Assemble the display module to LCD cover;
1.9:Assemble the 2 screws (M2.5*5mm)
Attention: the screw driver torque is 2.0-2.5Kgf-cm
;
Component P/N Qty
Screw E43-1255007-H29 2
CX600(MS-1682)Assembly Guide
1、 LCD MODULE ASSY
1.10:Stick three magnet to the position as left
picture shows;
Component P/N Qty
LCD Cover Magnet E2Y-2210512-SF7 2
LCD Cover Magnet E2Y-6710411-SF7 1
1.11:Assemble INVERTER
Component P/N Qty
INVERTER S78-3300470-SG3 1
1.12:Assemble the two LCD hinges on two
sides;Assemble the 6 screws (M2.5*5mm);
Attention: the screw driver torque is 2.0-2.5Kgf-cm
Component P/N Qty
Screw E43-1255007-H29 6
Hinge R E2M-6810411-G60 1
Hinge L E2M-6810511-G60 1
CX600(MS-1682)Assembly Guide
1、 LCD MODULE ASSY
1.13:When assemble the LCD bezel, should begin
from the two sides, then the upside to downside
assemble the 4screws (M2.5*5mm).;
Attention: the screw driver torque is 2.0-2.5Kgf-cm
Component P/N Qty
Screw E43-1255007-H29 4
LCD Bezel 307-681B211-Y31 1
1.14:Assemble the 8 cover rubber
Component P/N Qty
UP Rubber E2Y-6810111-Y40 4
DOWN Rubber E2Y-6740611-Y40 4
CX600(MS-1682)Assembly Guide
2、UPPER CASE ASSY
2.1:Insert the T/P module FFC according
to direction of left pic shows; then close the
connector that stabilize the T/P cable,;
Component P/N Qty
FFC Cable (To MB) K1C-1012040-J36 1
2.2:Assemble the Touchpad Module to Upper
Case fixed position,
Component P/N Qty
Touchpad Module S78-3700360-SD2 1
Upper Case 307-682C111-TC7 1
CX600(MS-1682)Assembly Guide
3、LOWER CASE ASSY
3.1:Assemble the RJ11 to Lower case;
Component P/N Qty
RJ11 CABLE K10-3002131-V03 1
3.2:Assemble the Speaker module to lower case
then lock the 4 screws (M2*3mm),;
Attention: the screw driver torque is 1.5-2.0Kgf-cm
Component P/N Qty
Screw E43-1203003-H29 4
Speaker Module S33-A020310-F33 1
Lower Case 307-681D221-Y31 1
CX600(MS-1682)Assembly Guide
3、LOWER CASE ASSY
3.3:Assemble the B/T module;
Component P/N Qty
Bluetooth Module 605-6837D-160 1
Main Board 607-16821-01S 1
3.4:Assemble the main board to Lower case; then
Lock the 1screw (M2.5*5mm)
Attention: the screw driver torque is 2.0-2.5Kgf-cm
Component P/N Qty
Screw E43-1255007-H29 4
CX600(MS-1682)Assembly Guide
3、LOWER CASE ASSY
3.5:Assemble the USB board, then lock the
1screw (M2.5*5mm)
Attention: the screw driver torque is 2.0-2.5Kgf-cm
Component P/N Qty
USB board 607-1682A-01S 1
Screw E43-1255007-H29 1
3.6:Assemble the USB board cable as left pic
shows:
Component P/N Qty
USB board FPC K1C-1012039-J36 1
CX600(MS-1682)Assembly Guide
4、ASSEMBLE UPPER CASE AND LOWER CASE
4.1:Assemble the 4 screws (M2.5*5mm)
Attention: the screw driver torque is 2.0-2.5Kgf-cm
Component P/N Qty
Screw E43-1255007-H29 4
4.2:Assemble 8 screws(M2.5*5mm)
Attention: the screw driver torque is 2.0-2.5Kgf-cm
Component P/N Qty
Screw E43-1255007-H29 8
4.3:Assemble 5 screws(M2.5*5mm)
Attention: the screw driver torque is 2.0-2.5Kgf-cm
Component P/N Qty
Screw E43-1255007-H29 5
CX600(MS-1682)Assembly Guide
4、ASSEMBLE UPPER CASE AND LOWER CASE
4.4:Connect the LVDS cable as pic shows:
4.5:Connect the Touchpad cable.
4.6:Assemble the modem, then lock the 2
screws(M2*3mm)
Attention: the screw driver torque is 1.5-2.0Kgf-cm
Component P/N Qty
MODEM S52-2801180-C59 1
Screw E43-1203003-H29 2
CX600(MS-1682)Assembly Guide
4、ASSEMBLE UPPER CASE AND LOWER CASE
4.7 : Assemble the 4 screws(M2.5*5mm) that
stabilize the LCD hinge.
Attention: the screw driver torque is 3.0-3.5Kgf-cm
Component P/N Qty
Screw E43-1255007-H29 4
4.8 : Assemble the 2 screws(M2*3mm) that
stabilize the hinge Cap
Attention: the screw driver torque is 1.5-2.0Kgf-cm
Component P/N Qty
Screw E43-1203003-H29 2
CX600(MS-1682)Assembly Guide
4、ASSEMBLE UPPER CASE AND LOWER CASE
4.9:Assemble Launch board according to the
direction that pic shows;
4.10:Assemble the 2 screws(M2*3mm);
Attention: the screw driver torque is: 1.5-2.0Kgf-cm
Component P/N Qty
Launch board 607-1682B-01S 1
Screw E43-1203003-H29 2
CX600(MS-1682)Assembly Guide
5、KEYBOARD
5.1:Insert the cable; close connector according to
the direction as pic shows;
Component P/N Qty
Keyboard S1N-3UUS1B1-C54 1
5.2:Assemble the 5 screws(M2*3mm);
Attention: the screw driver torque is: 1.5-2.0Kgf-cm
Component P/N Qty
Screw E43-1203003-H29 5
5.3:Assemble the Hinge Cover;
Component P/N Qty
Hinge Cover 307-682E221-Y31 1
CX600(MS-1682)Assembly Guide
6、THERMAL-KIT、CPU、DRAM AND WLAN MODULE
6.1:Assemble the RAM module according the
direction as pic shows;
Component P/N Qty
RAM Module S7C-S357701-T10 1
6.2:Assemble the WLAN module according to the
direction of pic shows;
Component P/N Qty
WLAN Module S57-0800290-T46 1
6.3:Assemble one screw(M2*3mm);then assemble
the two side wireless card antenna as pic shows:
Attention: the screw driver torque is: 1.5-2.0Kgf-cm
Component P/N Qty
Screw E43-1203003-H29 1
CX600(MS-1682)Assembly Guide
6、THERMAL-KIT、CPU、DRAM AND WLAN MODULE
6.4:Assemble CPU Module as below, Close the CPU
Slot with Screw Driver.
.
Component P/N Qty
CPU A09-21201G6-I06 1
6.5: Assemble the Fansink and FAN cable, after
that lock the 6 screws (M2.5*5mm).
Attention:the screw driver torque is 2.0-2.2Kgf-cm
Component P/N Qty
Screw E43-1255007-H29 6
Fansink E32-0800220-F05 1
54 1
2
6
3
CX600(MS-1682)Assembly Guide
7、ODD MODULE
7.1:Assemble ODD Bezel as below.
Component P/N Qty
ODD Bezel E2P-681F211-Y31 1
7.2:Assemble ODD Bracket as below, then lock 2pcs
M2*3mm Screws
Component P/N Qty
Screw E43-1203003-H29 2
ODD Bracket E2M-6510211-Y28 1
ODD Module S7D-2270015-H44 1
CX600(MS-1682)Assembly Guide
7、ODD MODULE
7.3:Assemble the ODD Module according to the
direction as pic shows;
7.4:Assemble the 1 screw(M2.5*5mm);
Attention: the screw driver torque: 2.0-2.5Kgf-cm
Component P/N Qty
Screw E43-1255007-H29 1
CX600(MS-1682)Assembly Guide
8、HDD MODULE
8.1:Assemble the HDD bracket;
Component P/N Qty
HDD Bracket 307-6810111-A89 1
HDD Module S71-2425521-W36 1
8.2 : Assemble the 2 screws(M3*3.5mm) that
stabilize the bracket;
Attention: the screw driver torque is 2.0-2.5Kgf-cm
Component P/N Qty
Screw E43-1303501-H29 2
CX600(MS-1682)Assembly Guide
8、HDD MODULE
8.3:Assemble the HDD Module according to the
direction as pic shows;
8.4:Assemble the 2 screws(M2.5*5mm);
Attention: the screw driver torque: 2.0-2.5Kgf-cm
Component P/N Qty
Screw E43-1255007-H29 2
CX600(MS-1682)Assembly Guide
9、BOTTOM DOOR ASSY
9.1:Assemble the Bottom door, then lock the 4
screws (M2.5*5mm).
Attention: the screw driver touque is: 2.0-2.5Kgf-cm
Component P/N Qty
Bottom door 307-681J211-Y31 1
Screw E43-1255007-H29 4
CX600(MS-1682)Assembly Guide
10、BATTERY PACK
10.1:Release the “Release” button and assemble
Battery Pack in the direction of arrow in the left
picture.
Component P/N Qty
Battery Pack S9N-2062200-CE1 1
10.2:Shift Unlock button to lock Battery Pack.