Okamura CorporationInternational Sales and Marketing DivisionAddress: 2-14-27 Akasaka, Minato-ku, Tokyo 107-0052 Japan
Phone : +81-3-5561-4085Fax : +81-3-5561-4086Website: http://www.okamura.co.jp/
Assembly Final Drawing (Name of each part)
Two persons should assemble this
product.
A cross slot screwdriver is required for
assembly. Please have one available.* Do not use an electric screwdriver
because it may damage the product.
Assembly Instruction ManualSpecial Edition
Desk
Thank you very much for purchasing the OKAMURA Study DESK. Before using this product, carefully read this Assembly Instruction Manual in order to fully under-stand and correctly assemble the product.
Movable shelf plate Movable divider
Fixed shelf plate
Movable shelf plate
Notch for mountingillumination
Lower shelf plate
Swing hook
Desktop
Drawer
■ Parallel placement example of desk and bookshelf
2 3
Locations of Caution Seals
(Attached to the desktop back side and fixed shelf plate back side)
(Attached to the shelf plate back face.)
(Do not remove the warning labels)
To Use SafelyThis indicates that improper handling due to disregard of this warning may result in injury or damage to property.
Fully read the instruction manual before assembly, securely tighten the bolts with a screwdriver, and use all of the assembly parts without leaving any parts unused to assemble correctly.
When assembling, do not use an electric screwdriver. When any force more than necessary is applied, the product may be broken or the bolt may not be removed.
After assembling, fully tighten the product on a flat surface, and make sure that each part is securely installed.
This product uses natural wood.Each product will have a slightly different appear-ance and may differ in wood grain and color from the catalog and sample products.
There may be some parts and members which are not used depending on the assembling pattern. Store them in a safe place as these parts will always be necessary when re-combining. Purchase parts again when they are lost.
Immediately after purchase, this product may emit adhesive or paint odors. In such a case, sufficiently ventilate and aerate. Periodically allow for ventilation.
When installing and moving this product, make sure two persons carry the product without dragging it.(Dragging the product may result in damage to floors.)
When the product is installed in a high humidity location, mold, etc., may grow. Periodically allow for ventilation.
CAUTIONCAUTION
CAUTIONCautions for assembly
Do not handle this product roughly or use for any other purpose than speci-fied. Never apply body weight to any point on the product, or ride on it. It may result in turnover or breakage, and is extremely dangerous.
Cautions for handling
Select a horizontal and stable location for installation. Use in a location where the floor is inclined or unstable may result in turnover or an accident, and is dangerous.
Avoid using this product in a location subject to direct sunlight, high temperatures or high humidity or in a location subject to direct heat and wind from a heating stove or air conditioner. It may result in alteration, deformation or discoloration.
Do not place any hot object directly on the product.It may result in alteration, deformation or discoloration.
Do not rub the product with hard material, and do not write with a writing instrument such as a ball-point pen with a hard tip without using a desk mat.It may result in deformation or flaws.
Periodically inspect for looseness of the bolts and connecting parts of the members, and securely re-tighten them when there is any looseness.Use while there is looseness may result in risks of deformation, breakage and turnover.
Do not allow the product to become wet and remain wet and do not leave a wet cloth on the product. It may result in deformation, cracks, swelling, stains or corrosion of the surface material. When the surface becomes wet, immediately wipe so that no moisture is left.
Do not attach any seals or cellophane tape, etc., to the product.It may result in removal of the surface material.
Cautions for installation
To ensure long-term use
Make sure to wipe with a dry and soft cloth along the wood grain. Use with a wet cloth may result in cracks and swelling. When the product is very dirty, moisten a soft cloth with a diluted neutral agent (dishwashing soap), and tightly squeeze it to wipe away dirt completely. And then, wipe with a soft dry cloth so that no soapy residue remains. When a large amount of moisture remains, deformation and discoloration may result.
Natural wood is natural material, therefore, the material will have its own unique grain and color. In other words, each product may differ slightly in color due to the characteristics of natural wood. In addition, natural wood is a material which breathes. Therefore, warpage or distortion may occur depending on use environment. These features give natural wood its attractive quality. The longer the product is used, the greater these features will be enhanced.* Natural wood means solid wood, back piece, laminated wood and sliced veneer, etc.
Do not use a lcohol-based or th inner-based solvent/chemical waste cloth or commercial cleaner since it will damage the surface. It may result in discoloration, etc.
About care
Characteristics of natural woods
Make sure to only place an object on the product within the maximum loading mass. Placing an object on the product heavier than the maximum loading mass may result in turnover or breakage, and is extremely dangerous.Desktop maximum loading mass = 40kg (Uniformly distributed mass)* Uniformly distributed mass means placing a mass uniformly on the desktop and shelf plate.
Diluted solvent Al
coho
l-bas
ed
solv
ent
Neutral agent(dishw
ashing soap)
MemoSeal
Assembly
Instruction
Manual
Check before assembling
Desktop Height, Chair Height/DepthOKAMURA Study DESK series complies with JIS Standard No. 2 (body height 120cm) through No. 6 (body height 180cm). The desktop height is five-stage adjustable.The following diagram shows bolt installation positions at the time of assembly according to each JIS No. In addition, height and depth of a chair sold separately is five-stage adjustable.Use at a proper height suitable for body height of your child.
<JIS standard No. and installation screw positions of desk (desktop) and chair (backrest/seating face)><Backrest>
No.6No.5No.4No.3No.2
No.6No.5No.4No.3No.2
No.6No.5No.4No.3No.2
<Seating face>
* This table shows standard reference dimensions. Make certain to determine the height and the depth of the desk and the chair according to the body height and the body size of your child.
Check before assembling Draw a circle around the No. applicable
to the body height of your child to determine the height of the desktop.
<JIS standard No. and reference of desk and chair height and depth>JIS standard No.
Standard body height (cm)
Desk
Chair
Desktop height (cm)
Seating face height (cm)
Seating face depth (cm)
No. 2 No. 3 No. 4 No. 5 No. 6
<JIS standard No. and body height reference> No. 6No. 5
No. 4No. 3
No. 2
Quality labeling seal
(Attached to the desktop back side)
Warning label
注意
Upper sideAssembled on rear face
2 3
Locations of Caution Seals
(Attached to the desktop back side and fixed shelf plate back side)
(Attached to the shelf plate back face.)
(Do not remove the warning labels)
To Use SafelyThis indicates that improper handling due to disregard of this warning may result in injury or damage to property.
Fully read the instruction manual before assembly, securely tighten the bolts with a screwdriver, and use all of the assembly parts without leaving any parts unused to assemble correctly.
When assembling, do not use an electric screwdriver. When any force more than necessary is applied, the product may be broken or the bolt may not be removed.
After assembling, fully tighten the product on a flat surface, and make sure that each part is securely installed.
This product uses natural wood.Each product will have a slightly different appear-ance and may differ in wood grain and color from the catalog and sample products.
There may be some parts and members which are not used depending on the assembling pattern. Store them in a safe place as these parts will always be necessary when re-combining. Purchase parts again when they are lost.
Immediately after purchase, this product may emit adhesive or paint odors. In such a case, sufficiently ventilate and aerate. Periodically allow for ventilation.
When installing and moving this product, make sure two persons carry the product without dragging it.(Dragging the product may result in damage to floors.)
When the product is installed in a high humidity location, mold, etc., may grow. Periodically allow for ventilation.
CAUTIONCAUTION
CAUTIONCautions for assembly
Do not handle this product roughly or use for any other purpose than speci-fied. Never apply body weight to any point on the product, or ride on it. It may result in turnover or breakage, and is extremely dangerous.
Cautions for handling
Select a horizontal and stable location for installation. Use in a location where the floor is inclined or unstable may result in turnover or an accident, and is dangerous.
Avoid using this product in a location subject to direct sunlight, high temperatures or high humidity or in a location subject to direct heat and wind from a heating stove or air conditioner. It may result in alteration, deformation or discoloration.
Do not place any hot object directly on the product.It may result in alteration, deformation or discoloration.
Do not rub the product with hard material, and do not write with a writing instrument such as a ball-point pen with a hard tip without using a desk mat.It may result in deformation or flaws.
Periodically inspect for looseness of the bolts and connecting parts of the members, and securely re-tighten them when there is any looseness.Use while there is looseness may result in risks of deformation, breakage and turnover.
Do not allow the product to become wet and remain wet and do not leave a wet cloth on the product. It may result in deformation, cracks, swelling, stains or corrosion of the surface material. When the surface becomes wet, immediately wipe so that no moisture is left.
Do not attach any seals or cellophane tape, etc., to the product.It may result in removal of the surface material.
Cautions for installation
To ensure long-term use
Make sure to wipe with a dry and soft cloth along the wood grain. Use with a wet cloth may result in cracks and swelling. When the product is very dirty, moisten a soft cloth with a diluted neutral agent (dishwashing soap), and tightly squeeze it to wipe away dirt completely. And then, wipe with a soft dry cloth so that no soapy residue remains. When a large amount of moisture remains, deformation and discoloration may result.
Natural wood is natural material, therefore, the material will have its own unique grain and color. In other words, each product may differ slightly in color due to the characteristics of natural wood. In addition, natural wood is a material which breathes. Therefore, warpage or distortion may occur depending on use environment. These features give natural wood its attractive quality. The longer the product is used, the greater these features will be enhanced.* Natural wood means solid wood, back piece, laminated wood and sliced veneer, etc.
Do not use a lcohol-based or th inner-based solvent/chemical waste cloth or commercial cleaner since it will damage the surface. It may result in discoloration, etc.
About care
Characteristics of natural woods
Make sure to only place an object on the product within the maximum loading mass. Placing an object on the product heavier than the maximum loading mass may result in turnover or breakage, and is extremely dangerous.Desktop maximum loading mass = 40kg (Uniformly distributed mass)* Uniformly distributed mass means placing a mass uniformly on the desktop and shelf plate.
Diluted solvent Al
coho
l-bas
ed
solv
ent
Neutral agent(dishw
ashing soap)
MemoSeal
Assembly
Instruction
Manual
Check before assembling
Desktop Height, Chair Height/DepthOKAMURA Study DESK series complies with JIS Standard No. 2 (body height 120cm) through No. 6 (body height 180cm). The desktop height is five-stage adjustable.The following diagram shows bolt installation positions at the time of assembly according to each JIS No. In addition, height and depth of a chair sold separately is five-stage adjustable.Use at a proper height suitable for body height of your child.
<JIS standard No. and installation screw positions of desk (desktop) and chair (backrest/seating face)><Backrest>
No.6No.5No.4No.3No.2
No.6No.5No.4No.3No.2
No.6No.5No.4No.3No.2
<Seating face>
* This table shows standard reference dimensions. Make certain to determine the height and the depth of the desk and the chair according to the body height and the body size of your child.
Check before assembling Draw a circle around the No. applicable
to the body height of your child to determine the height of the desktop.
<JIS standard No. and reference of desk and chair height and depth>JIS standard No.
Standard body height (cm)
Desk
Chair
Desktop height (cm)
Seating face height (cm)
Seating face depth (cm)
No. 2 No. 3 No. 4 No. 5 No. 6
<JIS standard No. and body height reference> No. 6No. 5
No. 4No. 3
No. 2
Quality labeling seal
(Attached to the desktop back side)
Warning label
注意
Upper sideAssembled on rear face
4 5
×2
×1
×5
×5
×2
×2
×8
×12
×4
×4
×4
Desk Details of Parts (make sure to check before assembly)
Key Organizer tray
Ring Desktop receiving dowel
Cap for insert nut Swing hook
Level adjustment felt
Single-endconnection bolt (24mm)
Actual sizeConnecting bolt (M6 × 45mm)
Connecting bolt (M6 × 35mm)
j k
a b
g hPlug cap(8mm)f
c d
e
i
Side panel (right and left) ×1
Side panel
Rear panel(lower)
This face is the under side
Rear panel (upper) ×1
Rear panel(lower) ×1
Lower shelf plate ×1
Desktop ×1
Desk
Installation of connecting bolts to side panel and rear panel (lower)Install five single-end connection bolts of c to the right and left side panels, and two locations of the rear panel (lower).
Turn c clockwise to screw in.
Desk
Desk Desk
Installation of rear panel (lower) and lower shelf plate
Installation of side panel and rear panel (upper)
Installation of desktop
Install the lower shelf plate to the rear panel (lower) and securely tighten the screw-type connector.
* Assemble the face to which a seal of the lower shelf plate is attached to the lower side.
Lower shelf plate
* Desktop height is five-stage adjustable.See page 3 to refer to the height.
Seal of “This face is lower”
Lower side
Securely tighten
Rear face plate (lower)
Screw-type connector
Install parts of 2 and rear panel (upper) to the right side panel, and then install the left side panel and securely tighten the screw-type connector.
When storing the two-stage wagon at desktop heights of JIS No. 2/3, it is necessary to separate the upper drawer unit (upper drawer) of the wagon. Please refer to page 11 for installation method.* When not installing the upper unit of the two-stage
wagon under the desktop, install the caps for nut of e at positions shown in the diagram.
Insert the desktop receiving dowels of d (4 locations) into the desktop receiving dowel holes provided on the side panel, and temporarily place the desktop.
* Make sure to install all of the desktop receiving dowels at the same height.
Desktop
Securely tighten
d
d
de
e
e
e
d
Actual size
Use a cross slot screwdriver for assembly.* An electric screwdriver or electric tool may damage the product, therefore, use a manual screwdriver.
[About screw-type connector]
Screw-type connector
The screw-type connector is tightened by turning clockwise.The screw-type connector is loosened by turning counterclockwise.
Screw-typeconnector
Single-end connection bolt
(Embedded into the members)
When the arrow is set to the single-end connection bolt, the connecting bolt is inserted (removed).
Arrow
Upper sideAssembled on rear face
Upper sideAssembled on rear face
[About connection bolt]
Single-end connection bolt
When screwing the connection bolts into the insert nuts, make sure not to tighten excessively.The insert nut may be removed, or the head of the connection bolt may be broken.
4 5
×2
×1
×5
×5
×2
×2
×8
×12
×4
×4
×4
Desk Details of Parts (make sure to check before assembly)
Key Organizer tray
Ring Desktop receiving dowel
Cap for insert nut Swing hook
Level adjustment felt
Single-endconnection bolt (24mm)
Actual sizeConnecting bolt (M6 × 45mm)
Connecting bolt (M6 × 35mm)
j k
a b
g hPlug cap(8mm)f
c d
e
i
Side panel (right and left) ×1
Side panel
Rear panel(lower)
This face is the under side
Rear panel (upper) ×1
Rear panel(lower) ×1
Lower shelf plate ×1
Desktop ×1
Desk
Installation of connecting bolts to side panel and rear panel (lower)Install five single-end connection bolts of c to the right and left side panels, and two locations of the rear panel (lower).
Turn c clockwise to screw in.
Desk
Desk Desk
Installation of rear panel (lower) and lower shelf plate
Installation of side panel and rear panel (upper)
Installation of desktop
Install the lower shelf plate to the rear panel (lower) and securely tighten the screw-type connector.
* Assemble the face to which a seal of the lower shelf plate is attached to the lower side.
Lower shelf plate
* Desktop height is five-stage adjustable.See page 3 to refer to the height.
Seal of “This face is lower”
Lower side
Securely tighten
Rear face plate (lower)
Screw-type connector
Install parts of 2 and rear panel (upper) to the right side panel, and then install the left side panel and securely tighten the screw-type connector.
When storing the two-stage wagon at desktop heights of JIS No. 2/3, it is necessary to separate the upper drawer unit (upper drawer) of the wagon. Please refer to page 11 for installation method.* When not installing the upper unit of the two-stage
wagon under the desktop, install the caps for nut of e at positions shown in the diagram.
Insert the desktop receiving dowels of d (4 locations) into the desktop receiving dowel holes provided on the side panel, and temporarily place the desktop.
* Make sure to install all of the desktop receiving dowels at the same height.
Desktop
Securely tighten
d
d
de
e
e
e
d
Actual size
Use a cross slot screwdriver for assembly.* An electric screwdriver or electric tool may damage the product, therefore, use a manual screwdriver.
[About screw-type connector]
Screw-type connector
The screw-type connector is tightened by turning clockwise.The screw-type connector is loosened by turning counterclockwise.
Screw-typeconnector
Single-end connection bolt
(Embedded into the members)
When the arrow is set to the single-end connection bolt, the connecting bolt is inserted (removed).
Arrow
Upper sideAssembled on rear face
Upper sideAssembled on rear face
[About connection bolt]
Single-end connection bolt
When screwing the connection bolts into the insert nuts, make sure not to tighten excessively.The insert nut may be removed, or the head of the connection bolt may be broken.
6 7
×8
×8
×8
×2
×3
×4
×16
Desk
Fixation of desktop, installation of hook
Desk 5 Fixation of desktop, installation of hookAfter temporarily placing the desktop on the desktop receiving dowels, insert the rings of b into the holes on outside of the side panel, and tighten with the connecting bolts of a.Install the swing hooks of g on the right and left sides at the positions shown in the diagram.When only using the desk, install the plug caps of f to the upper part of the side panel to complete installation.
The movable divider attached to the bookshelf can also be used for the desktop.Insert the movable divider into the notch part of the desktop and slide laterally to install.
Desktop
Swinghook
Swing hook
* Proceed to the bookshelf assembly in a state that the desktop is installed.
When using the product in connection with the bookshelf, proceed to the bookshelf assembly on page 7.
ab
b
b
b
g
a
a
aa
f f
ff
ab
When using the desk and bookshelf separatelyDesk
Installation of movable divider(at desktop height No. 2 through No. 6)
Movable divider
Notch part
Bookshelf Details of Parts (make sure to check before assembly)Cap for insert nut
Shelf receiving fitting pin (M6)
Actual sizeConnecting bolt(M6 × 45mm)
l Plug cap(11mm)
Plug cap(8mm)e
m
f o
n Single-end connectionbolt (24mm/40mm)
c Single-end connection bolt(24mm)
Fixed shelf plate ×1
Rear panel(upper) ×1
Rear panel(middle) ×1
Movable divider ×4
Right side panel
Turn c clockwise to screw.
Right side panel Left side panel
Rear panel (lower) ×1(Wider plate)
Movable shelf plate ×2
Bookshelf
IInstallation of connecting bolt to side panelInstall eight single-end connection bolts of c on the right and left side panels.
Use a cross slot screwdriver for assembly.* An electric screwdriver or electric tool may damage the product, therefore, use a manual screwdriver.
Left side panel
[About screw-type connector]
Screw-type connector
The screw-type connector is tightened by turning clockwise.The screw-type connector is loosened by turning counterclockwise.
Screw-typeconnector
Single-end connection bolt
(Embedded into the members)
When the arrow is set to the single-end connection bolt, the connecting bolt is inserted (removed).
Arrow
Upper sideAssembled on rear face
[About connection bolt]
Single-end connection bolt
When screwing the connection bolts into the insert nuts, make sure not to tighten excessively.The insert nut may be removed, or the head of the connection bolt may be broken.
6 7
×8
×8
×8
×2
×3
×4
×16
Desk
Fixation of desktop, installation of hook
Desk 5 Fixation of desktop, installation of hookAfter temporarily placing the desktop on the desktop receiving dowels, insert the rings of b into the holes on outside of the side panel, and tighten with the connecting bolts of a.Install the swing hooks of g on the right and left sides at the positions shown in the diagram.When only using the desk, install the plug caps of f to the upper part of the side panel to complete installation.
The movable divider attached to the bookshelf can also be used for the desktop.Insert the movable divider into the notch part of the desktop and slide laterally to install.
Desktop
Swinghook
Swing hook
* Proceed to the bookshelf assembly in a state that the desktop is installed.
When using the product in connection with the bookshelf, proceed to the bookshelf assembly on page 7.
ab
b
b
b
g
a
a
aa
f f
ff
ab
When using the desk and bookshelf separatelyDesk
Installation of movable divider(at desktop height No. 2 through No. 6)
Movable divider
Notch part
Bookshelf Details of Parts (make sure to check before assembly)Cap for insert nut
Shelf receiving fitting pin (M6)
Actual sizeConnecting bolt(M6 × 45mm)
l Plug cap(11mm)
Plug cap(8mm)e
m
f o
n Single-end connectionbolt (24mm/40mm)
c Single-end connection bolt(24mm)
Fixed shelf plate ×1
Rear panel(upper) ×1
Rear panel(middle) ×1
Movable divider ×4
Right side panel
Turn c clockwise to screw.
Right side panel Left side panel
Rear panel (lower) ×1(Wider plate)
Movable shelf plate ×2
Bookshelf
IInstallation of connecting bolt to side panelInstall eight single-end connection bolts of c on the right and left side panels.
Use a cross slot screwdriver for assembly.* An electric screwdriver or electric tool may damage the product, therefore, use a manual screwdriver.
Left side panel
[About screw-type connector]
Screw-type connector
The screw-type connector is tightened by turning clockwise.The screw-type connector is loosened by turning counterclockwise.
Screw-typeconnector
Single-end connection bolt
(Embedded into the members)
When the arrow is set to the single-end connection bolt, the connecting bolt is inserted (removed).
Arrow
Upper sideAssembled on rear face
[About connection bolt]
Single-end connection bolt
When screwing the connection bolts into the insert nuts, make sure not to tighten excessively.The insert nut may be removed, or the head of the connection bolt may be broken.
8 9
o
l
l
l
l
l
l
l
l
o
o
Securely tighten
Bookshelf Installation of rear panel (middle) and fixed shelf plate
Install the rear panel (middle) to the fixed shelf plate with the connecting bolt of o, and securely tighten.Assemble so that the seal is at the upper side rear face.
Fixed shelf plate
Right side panel
Rear panel (upper)
Rear panel (lower)
Left side panel
Rear panel
Bookshelf Installation of side panel and rear panel
Install the parts of 2 and the rear panels (upper and lower) to the left side panel, and then install the right side panel, and securely tighten the screw-type connec-tor.
Assemble so that the seal is at the upper side rear face.
A. When only using the bookshelf, proceed to A-4. B. When using in connection with the desk, proceed to B-4.
Bookshelf Installation of movable shelf plate with drawer and movable shelf plate
For installation of the movable shelf plate, after installing the shelf receiving fitting pin of l, install the movable shelf plate and tighten with the connecting bolt of o from the rear of the rear panel.
Movable shelf plate
Movable shelf plate
Bookshelf
Tightening of fitting, installation of movable dividerSecurely tighten the fitting on the movable shelf plate with a screwdriver from above.
■ How to install and remove movable divider
Insert the movable divider into the notch on the desk, and slide it to install.When removing, s l ide the movable divider to the notch part to remove.
Securely tighten
Each screw-type connector
Notch part
Tighten counterclockwise.Tighten counterclockwise.
When tightening from above
Tighten
Completion
Loosen
* When tightening the bolt from above the shelf plate, turn counterclock-wise.
Page11 Proceed to “Two-stage drawer unit and illumination”
Installation of both-side connecting bolt to desk
Desk + bookshelf
Insert the both-side connecting bolt of n into the hole on the upper part of the desk side panel, install the bookshelf and securely tighten the screw-type con-nector.
Securely tighten
Long
Short
nn
nn
Connection of desk completed on Page 6 and bookshelf
Upper sideAssembled on rear face
Upper sideAssembled on rear face
8 9
o
l
l
l
l
l
l
l
l
o
o
Securely tighten
Bookshelf Installation of rear panel (middle) and fixed shelf plate
Install the rear panel (middle) to the fixed shelf plate with the connecting bolt of o, and securely tighten.Assemble so that the seal is at the upper side rear face.
Fixed shelf plate
Right side panel
Rear panel (upper)
Rear panel (lower)
Left side panel
Rear panel
Bookshelf Installation of side panel and rear panel
Install the parts of 2 and the rear panels (upper and lower) to the left side panel, and then install the right side panel, and securely tighten the screw-type connec-tor.
Assemble so that the seal is at the upper side rear face.
A. When only using the bookshelf, proceed to A-4. B. When using in connection with the desk, proceed to B-4.
Bookshelf Installation of movable shelf plate with drawer and movable shelf plate
For installation of the movable shelf plate, after installing the shelf receiving fitting pin of l, install the movable shelf plate and tighten with the connecting bolt of o from the rear of the rear panel.
Movable shelf plate
Movable shelf plate
Bookshelf
Tightening of fitting, installation of movable dividerSecurely tighten the fitting on the movable shelf plate with a screwdriver from above.
■ How to install and remove movable divider
Insert the movable divider into the notch on the desk, and slide it to install.When removing, s l ide the movable divider to the notch part to remove.
Securely tighten
Each screw-type connector
Notch part
Tighten counterclockwise.Tighten counterclockwise.
When tightening from above
Tighten
Completion
Loosen
* When tightening the bolt from above the shelf plate, turn counterclock-wise.
Page11 Proceed to “Two-stage drawer unit and illumination”
Installation of both-side connecting bolt to desk
Desk + bookshelf
Insert the both-side connecting bolt of n into the hole on the upper part of the desk side panel, install the bookshelf and securely tighten the screw-type con-nector.
Securely tighten
Long
Short
nn
nn
Connection of desk completed on Page 6 and bookshelf
Upper sideAssembled on rear face
Upper sideAssembled on rear face
10 11
Desktop (install later)
Installation of movable shelf plateDesk + bookshelf
For installation of the movable shelf plate, after installing the shelf receiving fitting pin of l, install the movable shelf plate, and tighten with the connecting bolts of h from the rear of the rear panel.
Installing position of the shelf plate is two-location selectable.
h
h
l
l
l
l
Tightening of boltsDesk + bookshelf
The bolts for the movable shelf plate with drawer and the movable shelf plate can be tightened from both of above and below, however, tighten clockwise from below and tighten counterclockwise from above.
When tightening from below
When tightening from above
When tighteningfrom below
Tighten
* When tightening the bolt from below the shelf plate, turn clockwise.
LoosenTighten clockwise.
Tighten counterclockwise.Tighten counterclockwise.
When tightening from above
Tighten
* When tightening the bolt from above the shelf plate, turn counterclockwise.
Loosen
Installation of movable dividerDesk + bookshelf
The movable divider can be installed to the desired notch part shown in the diagram.Insert the plate from the notch parts on the right and left sides of the bookshelf and desk, and slide laterally to install.
Completion
Two-stage wagon drawer unit and lighting
How to store drawer unit
Securely tighten.
Screw-type connector
Drawer unit
Clamp withreceptacle outlet
Lighting can be installed to the notch parts on the right and left sides of the desk with a clamp.* Refer to the “Instruction manual” attached to the illumination.
Lighting installing position
When you purchased the dedicated two-stage wagon, it is necessary to separate the drawer unit (upper drawer) when the desktop height is JIS No. 2 and No.3.The separated unit can be stored in the fixed lower shelf plate as shown in the diagram.① Separate the wagon, and remove the drawer unit and the single-end connection bolts from
the wagon body.② Screw the removed connecting bolts into the locations shown in
the diagram.* The installing location is only the right side toward the main body.
③ Install the drawer unit such that the drawer front panel is directed upward, and turn the screw-type connectors two positions to the left in the clockwise direction to tighten.
(So that the front panel is directed upward)
10 11
Desktop (install later)
Installation of movable shelf plateDesk + bookshelf
For installation of the movable shelf plate, after installing the shelf receiving fitting pin of l, install the movable shelf plate, and tighten with the connecting bolts of h from the rear of the rear panel.
Installing position of the shelf plate is two-location selectable.
h
h
l
l
l
l
Tightening of boltsDesk + bookshelf
The bolts for the movable shelf plate with drawer and the movable shelf plate can be tightened from both of above and below, however, tighten clockwise from below and tighten counterclockwise from above.
When tightening from below
When tightening from above
When tighteningfrom below
Tighten
* When tightening the bolt from below the shelf plate, turn clockwise.
LoosenTighten clockwise.
Tighten counterclockwise.Tighten counterclockwise.
When tightening from above
Tighten
* When tightening the bolt from above the shelf plate, turn counterclockwise.
Loosen
Installation of movable dividerDesk + bookshelf
The movable divider can be installed to the desired notch part shown in the diagram.Insert the plate from the notch parts on the right and left sides of the bookshelf and desk, and slide laterally to install.
Completion
Two-stage wagon drawer unit and lighting
How to store drawer unit
Securely tighten.
Screw-type connector
Drawer unit
Clamp withreceptacle outlet
Lighting can be installed to the notch parts on the right and left sides of the desk with a clamp.* Refer to the “Instruction manual” attached to the illumination.
Lighting installing position
When you purchased the dedicated two-stage wagon, it is necessary to separate the drawer unit (upper drawer) when the desktop height is JIS No. 2 and No.3.The separated unit can be stored in the fixed lower shelf plate as shown in the diagram.① Separate the wagon, and remove the drawer unit and the single-end connection bolts from
the wagon body.② Screw the removed connecting bolts into the locations shown in
the diagram.* The installing location is only the right side toward the main body.
③ Install the drawer unit such that the drawer front panel is directed upward, and turn the screw-type connectors two positions to the left in the clockwise direction to tighten.
(So that the front panel is directed upward)
Okamura CorporationInternational Sales and Marketing DivisionAddress: 2-14-27 Akasaka, Minato-ku, Tokyo 107-0052 Japan
Phone : +81-3-5561-4085Fax : +81-3-5561-4086Website: http://www.okamura.co.jp/
Assembly Final Drawing (Name of each part)
Two persons should assemble this
product.
A cross slot screwdriver is required for
assembly. Please have one available.* Do not use an electric screwdriver
because it may damage the product.
Assembly Instruction ManualSpecial Edition
Desk
Thank you very much for purchasing the OKAMURA Study DESK. Before using this product, carefully read this Assembly Instruction Manual in order to fully under-stand and correctly assemble the product.
Movable shelf plate Movable divider
Fixed shelf plate
Movable shelf plate
Notch for mountingillumination
Lower shelf plate
Swing hook
Desktop
Drawer
■ Parallel placement example of desk and bookshelf