DRILLING SERVICES Directional Drilling Technologies
Navi-Drill™ Ultra™ SeriesDirectional drilling motors
Applicationsyy Shale gas, onshore, and conventional/unconventionalyy Vertical and directional drillingyy Performance drillingyy Underbalanced drillingyy Re-entry and slim hole drillingyy Hard/abrasive formations and
high-temperature environments
Featuresyy Titanium flex shaft improves reliability compared to
universal jointyy Optimized connections increase motor reliabilityyy High-temperature elastomeryy Extended length of the power section (Ultra XL)yy Adjustable kickoff sub (AKO)
Tool size 23⁄8-in. to 12¾-in. (60 mm to 313 mm)
Hole size 2¾-in. to 44-in. (70 mm to 1,118 mm)
Navi-Drill™ Ultra-HP™ SeriesHigh-performance drilling motors
Applicationsyy Shale gas, onshore, and conventional/unconventionalyy Vertical and directional drillingyy Performance drillingyy OBM environmentsyy Underbalanced drillingyy Re-entry and slim hole drillingyy Hard/abrasive formations
Featuresyy DuraMax high-performance elastomer technologyyy Titanium flex shaft improves reliability compared
to universal jointyy Optimized connections increase motor reliabilityyy Adjustable kickoff sub (AKO)
Tool size 23⁄8-in. to 9½-in. (60 mm to 241 mm)
Hole size 2¾-in. to 28-in. (70 mm to 711 mm)
AutoTrak™ X-tremeMotor-powered rotary steerable system
Applicationsyy Horizontal extended-reach and tight wellbore
spacing wellsyy Complex 3D directional profilesyy Conventional, unconventional, onshore, offshore and
deep water
Featuresyy Pre-contoured X-treme or Ultra HP and wired motoryy Fully modular system, integrated BHA with
short-spaced advanced MWD/LWD sensorsyy Automated 3D continuous proportional
steering methodyy Real-time near-bit inclination and
bidirectional communicationyy Steering mechanism independent of hydraulic
parameters such as flow rate, bit pressure drop, and mud properties
yy Optional near-bit gamma (ZoneTrak G)
Tool size4¾-in. (121 mm)6¾-in. (171 mm)9½-in. (241 mm)
Hole size 5¾-in. to 28-in. (146 mm to 711 mm)
Navi-Drill™ Ultra™ X-treme SeriesDirectional drilling motors
Applicationsyy Shale gas, deep water, geothermal, onshore/offshore,
and conventional/unconventionalyy Vertical and directional drillingyy Performance drillingyy Re-entry and slim hole drillingyy Hard/abrasive formations and
high-temperature environments
Featuresyy X-treme pre-contoured power sectionyy Titanium flex shaftyy Optimized connections increase motor reliabilityyy High-temperature elastomeryy High weight on bit (WOB) bearing assemblyyy Adjustable kickoff sub (AKO)
Tool size 23⁄8-in. to 12¾-in. (60 mm to 313 mm)
Hole size 2¾-in. to 44-in. (70 mm to 1,118 mm)
Navi-Drill™ X-treme SeriesHigh-performance drilling motors
Applicationsyy Shale gas, deep water, geothermal, onshore/offshore,
and conventional/unconventionalyy Vertical and directional drillingyy Performance drillingyy Re-entry and slim hole drillingyy Hard/abrasive formations and high-temperature
environments
Featuresyy X-treme pre-contoured power sectionyy Titanium flex shaftyy Optimized connections increase motor reliabilityyy High-temperature elastomeryy High weight on bit (WOB) bearing assemblyyy Adjustable kickoff sub (AKO)
Tool size 23⁄8-in. to 12¾-in. (60 mm to 313 mm)
Hole size 2¾-in. to 44-in. (70 mm to 1,118 mm)
Navi-Drill™ Ultra™ Curve SeriesHigh BUR directional drilling motors
Applicationsyy Shale gas, onshore, and conventional/unconventionalyy Vertical, directional and horizontal drillingyy Performance drillingyy High-Temperature and OBM environments yy Underbalanced drillingyy Hard/abrasive formations
Featuresyy Reduced bit-to-bend lengthyy DuraMax high-performance elastomeryy Extended-length power sectionsyy Titanium flex shaftyy Optimized connections and high make-up torque yy High temperature elastomeryy Adjustable kickoff sub (AKO)
Tool size 6¾-in. (171 mm)
Hole size 8½-in. to 8¾-in. (216 mm to 222 mm)
© 2017 Baker Hughes, a GE company, LLC – All rights reserved.
Baker Hughes, a GE company, LLC and its affiliates (“BHGE”) provides this information on an “as is” basis for general information purposes and believes it to be accurate as of the date of publication. BHGE does not make any representation as to the accuracy or completeness of the information and makes no warranties of any kind, specific, implied or oral, to the fullest extent permissible by law, including those of merchantability and fitness for a particular purpose or use. BHGE hereby disclaims any and all liability for any direct, indirect, consequential or special damages, claims for lost profits, or third party claims arising from the use of the information, whether a claim is asserted in contract, tort, or otherwise. The BHGE logo is a trademark of Baker Hughes, a GE company, LLC. GE and the GE monogram are trademarks of General Electric Company used under trademark license.
67259
bhge.com
AutoTrak™ VVertical seeking rotary steerable system
Applicationsyy Areas with high formation dips and
deviation tendenciesyy No directional MWD requirementsyy Conventional, unconventional, onshore
and offshore
Featuresyy Simple deployment with minimal surface setupyy Automated 3D continuous proportional
steering methodyy Real-time near-bit inclination and
bidirectional communicationyy Steering mechanism independent of hydraulic
parameters such as flow rate, bit pressure drop, and mud properties
yy Optional downhole motor
Tool size4¾-in. (121 mm)6¾-in. (171 mm) 9½-in. (241 mm)
Hole size 5¾-in. to 28-in. (146 mm to 711 mm)
AutoTrak™ eXpressBasic rotary steerable system
Applicationsyy Field development, probe based directional
MWD serviceyy Conventional, unconventional and onshore
Featuresyy Simple deployment with minimal surface setupyy Automated 3D continuous proportional
steering methodyy Real-time near-bit inclination and
bidirectional communicationyy Steering mechanism independent of hydraulic
parameters such as flow rate, bit pressure drop, and mud properties
yy Optional downhole motoryy Optional gamma ray
Tool size4¾-in. (121 mm) 6¾-in. (171 mm)9½-in. (241 mm)
Hole size 5¾-in. to 28-in. (146 mm to 464 mm)
AutoTrak™ CurveHigh-build rate rotary steerable system
Applicationsyy Vertical, 3D directional, high-build curve and
horizontal drillingyy Probe based directional MWD serviceyy Conventional, unconventional and onshoreyy Pad, high-volume and tight wellbore spacing
drilling environments
Featuresyy Reaches high buildup rates, up to 15°/100ftyy Real-time near-bit gamma and high
frequency vibrationsyy Optimized single piece BHA with higher LCM toleranceyy Automated 3D continuous proportional
steering methodyy Real-time near-bit inclination and
bidirectional communicationyy Steering mechanism independent of hydraulic
parameters such as flow rate, bit pressure drop, and mud properties
yy Includes BHGE Drill Bitsyy Optional downhole motor
Tool size 6¾-in. (171 mm)
Hole size 83⁄8-in. to 105⁄8-in. (213 mm to 270 mm)
AutoTrak™ eXactAdvanced high-build rate rotary steerable system
Applicationsyy Real-time reservoir navigation, integrating multiple
MWD/LWD measurementsyy Multilateral, complex 3D designer,
extended-reach and tight wellbore spacing wellsyy Conventional, unconventional, onshore
and offshore
Featuresyy Reaches high buildup rates, up to 10°/100ftyy Real-time near-bit high frequency vibrationsyy Fully modular system, integrated BHA with
short-spaced advanced MWD/LWD sensorsyy Automated 3D continuous proportional
steering methodyy Real-time near-bit inclination and
bidirectional communicationyy Steering mechanism independent of hydraulic
parameters such as flow rate, bit pressure drop, and mud properties
yy Optional downhole motoryy Optional near-bit gamma (ZoneTrak G)
Tool size 4¾-in. (121 mm)6¾-in. (171 mm)
Hole size 5¾-in. to 105⁄8-in. (146 mm to 270 mm)
AutoTrak™ G3Advanced rotary steerable system
Applicationsyy Real-time reservoir navigation, integrating multiple
MWD/LWD measurementsyy Multilateral, complex 3D designer,
extended-reach and tight wellbore spacing wellsyy Conventional, unconventional, onshore, offshore
and deep water
Featuresyy Fully modular system, integrated BHA with
short-spaced advanced MWD/LWD sensorsyy Automated 3D continuous proportional
steering methodyy Real-time near-bit inclination and
bidirectional communicationyy Steering mechanism independent of hydraulic
parameters such as flow rate, bit pressure drop, and mud properties
yy Optional downhole motor (AutoTrak X-treme)yy Optional near-bit gamma (ZoneTrak G)
Tool size
4¾-in. (121 mm)6¾-in. (171 mm)8¼-in. (210 mm)9½-in. (241 mm)
Hole size 5¾-in. to 28-in. (146 mm to 711 mm)
NaviTrak™
Directional and gamma MWD service
TeleTrak™
Directional and gamma MWD service
GyroTrak™
Gyroscopic MWD service
Applicationsyy Unconventional shale playsyy Onshore development drillingyy Factory drilling
Featuresyy Real-time directional information yy Downlink capability yy Real-time gamma ray logsyy Optional flow-off logging
Applicationsyy High-LCM environmentsyy Unconventional shale playsyy Onshore development drilling yy Factory drilling
Featuresyy Proven tolerance to high solids and LCM concentrationyy Real-time directional information, including hole
inclination, azimuth, and toolface orientationyy Downlink capability improves telemetry ratesyy Single turbine/restrictor configurationyy Real-time gamma ray logs
Applicationsyy Nearby well casing interferenceyy Kickoff below a casing shoeyy Whipstock orientation and millingyy Relief-well drilling
FeaturesRobust gyroscopic measurements
Tool size
31⁄8-in. (79.4 mm)4¾-in. (120.7 mm)6¾-in. (171.5 mm) 8¼-in. (209.6 mm) 9½-in. (241.3 mm)
Probe diameter 1¾-in. (45 mm)
Hole size 37⁄8-in. to 17½-in. (98 mm to 445 mm)
Tool size4¾-in. (121 mm)6½-in. (165 mm)6¾-in. (172 mm)
Hole size 57⁄8-in. to 97⁄8-in. (149 mm to 250 mm)
Tool size
OnTrak:6¾-in. (172 mm)8¼-in. (210 mm) 9½-in. (241 mm)
NaviTrak:
4¾-in. (152 mm) 6¾-in. (172 mm) 8¼-in. (210 mm) 9½-in. (241 mm)
CoilTrak: 23⁄8-in. (60 mm)3-in (76.2 mm)
Hole size
OnTrak: 83⁄8-in. to 26-in. (214 mm to 660 mm)
NaviTrak: 37⁄8-in. to 17½-in. (128 mm to 312 mm)
CoilTrak: 2¾-in. to 4¾-in. (89 mm to 121 mm)
OnTrak™
Integrated MWD and LWD service
AziTrak™
Deep azimuthal resistivity LWD tool
Applicationsyy Offshore exploration and development yy Complex directional targetsyy Geosteering
Featuresyy Azimuthal gamma ray with imaging capabilityyy High-frequency phase resistivityyy Low-frequency attenuation resistivityyy Fast two-way communication between the surface
and downhole
Applicationsyy Conventional oil and gas reservoirsyy Deep water drillingyy High-angle and horizontal wellsyy Brownfield production enhancementyy Field development through infill drilling
Featuresyy Compact, fully integrated sub featuring
close-to-the-bit measurementsyy Close-to-the-bit, deep-reading azimuthal resistivity
allows early detection of remote conductive boundaries yy Intuitive, dynamic, real-time display of
reservoir boundaries
Tool size
4¾-in. (121 mm)6¾-in. (172 mm)8¼-in. (210 mm)9½-in. (241 mm)
Hole size 5¾-in. to 26-in. (146 mm to 669 mm)
Tool size 4¾-in. (121 mm)6¾-in. (172 mm)
Hole size 5¾-in. to 105⁄8-in. (146 mm to 270 mm)
ZoneTrak™ RAt-bit resistivity LWD service
Applicationsyy Casing and coring point selectionyy Salt exit detectionyy Real-time pressure managementyy Geo-stoppingyy All drilling environmentsyy High-resistivity contrast formations
Featuresyy Identifies top and bottom of reservoiryy Detects formation changes faster to adjust drilling
fluid parametersyy Includes forward response modelingyy Real-time data transmitted through BHGE
WellLink™ service
Tool size 6¾-in. (172 mm)9½-in. (241 mm)
Hole size 83⁄8-in. to 18¼-in. (213 mm to 464 mm), dependent upon mud type
ZoneTrak™ GNear-bit gamma service
Applicationsyy Casing and coring point selectionyy Geo-stopping yy Reservoir navigation yy All drilling environments
Featuresyy True azimuthal gamma ray measures 6 feet above
the bityy Imaging capabilitiesyy Two gamma sensors yy Real-time gamma data can be displayed through BHGE
WellLink™ service
Tool size4¾-in. (121 mm)6¾-in. (172 mm)9½-in. (241 mm)
Hole size 5¾-in. to 18¼-in. (146 mm to 464 mm)
aXcelerate™ PLUSHigh-speed mud-pulse telemetry service
Applicationsyy Critical wellsyy Geosteering and optimized wellbore placementyy Extended-reach and complex 3D wellsyy Performance drillingyy Required for extended formation
evaluation BHA’s
Featuresyy Downhole adjustable pulser setup via downlinkyy Real-time formation evaluation data for
reservoir navigationyy High-resolution downhole drilling dynamics data yy Bandwidth up to 40 bits per second physical and up to
256 bits per second compressed
Tool size 4¾-in. (121 mm)6¾-in. (172 mm)
Hole size 5¾-in. to 105⁄8-in. (146 mm to 270 mm)
Wired-Pipe TelemetryApplicationsyy Extended-reach wellsyy Underbalanced drillingyy Geosteeringyy Performance drillingyy Required for extended formation evaluation BHA’syy Enabling technology for delivering measurements
along the string
Featuresyy Real-time formation evaluation memory quality data
for reservoir navigationyy Bandwidth up to 57,600 bits per secondyy High-resolution downhole drilling dynamics data of the
BHA and optional along the stringyy Drilling in environments where data transmission was
not possible with mud pulse telemetry
Tool size
4¾-in. (121 mm)6¾-in. (171 mm)8¼-in. (210 mm)9½-in. (241 mm)
Hole size 5¾-in. to 26-in. (146 mm to 660 mm)
SureTrak™
Steerable drilling liner service
GaugePro™ XPR/XPSConcentric expandable hole enlargement
GaugePro™ EchoOn Command Digital Downhole Reamer
Applicationsyy Onshore or offshore environments yy Interbedded formationsyy Wellbore instability issues, including swelling shale
and weak sedimentsyy Lost circulationyy Depleted formations
Featuresyy Changeable pilot bottomhole assembly (BHA)
eliminates the need for liner retrieval yy BHA design tailored to wellsite requirementsyy Uses AutoTrak™ system with modular
MWD/LWD servicesyy Incorporates X-treme motor technologyyy Liner shoe with decoupled reamer bit separates BHA
drilling dynamics from the liner
Applicationsyy Rotary steerable and rotary operations yy Deepwater projectsyy Wellbore enlargementyy Unconsolidated formationsyy Salt drilling
Featuresyy StaySharp™ premium polished cutter technology with
improved diamond material and interfaceyy StayTough™ hardfacingyy Active blade retraction yy Application-specific cutter blades yy Blade operation, protecting the casing
Applicationsyy Deep water & on-shore projectsyy Selective under reamingyy ECD managementyy Rat-Hole eliminationyy Hole cleaning
Featuresyy On-Demand unlimited activationsyy 5 minute activation/deactivationyy Real-time communicationyy Downlink via Mud Pulse or wired drill pipeyy Confirms real-time cutter blade actuation and
OD positionyy Real-time VSS and tool diagnosticsyy No pressure drop dependencies, no shoulder testsyy Up to 3 reamers in one BHAyy Independent of mud flowyy Memory for post analysis
Tool size 4¾-in. with 7-in. liner 6¾-in. with 95⁄8-in. liner
Hole size 8½-in. to 12¼-in. (216 mm to 311 mm)
Series 6 6-in. x 7-in.
Series 6.5 6½-in. 7½-in.
Series 8 8½-in. x 97⁄8-in.
Series 9 9½-in. x 11¾-in.
Series 10 105⁄8-in. x 12¼-in.
Series 12 12¼-in. x 14¾-in.
Series 13 13½-in. x 16-in.
Series 14 14½-in. x 17½-in.
Series 16 16½-in. x 20-in.
Series 18 181⁄8-in. x 22-in.
BHA Body Pass-Thru Maximum Hole Size
Series 6 4¾-in. 6-in. 8¾-in.
Series 8 6¾-in. 8½-in. 97⁄8-in.
Series 10 8¼-in. 105⁄8-in. 12¼-in.
Series 12 9½-in. 12¼-in. 14¾-in.
Series 14 9½-in. 14½-in. 17¾-in.
Series 16 9½-in. 16½-in. 22-in.
SIGNALS™ SurveillanceOperations Monitoring Services
SIGNALS™ ServicesWellsite and remote operations monitoring
ApplicationsAll Drilling Environments
Featuresyy Collection and interpretation of real-time
operational datayy Detailed record of drilling parametersyy Provides integrated data visualization yy Structured workflow and proactive
communication protocols
SIGNALS™ DefenseWellbore Integrity Services
SIGNALS™ OptimeDrilling Optimization Services
Applicationsyy Exploration Wellsyy Offshore drilling environmentsyy Narrow pressure windows yy Complex and problematic formations
Featuresyy Early kick detection with automated smart alarmsyy Identification of wellbore instability issuesyy Pore pressure trend analysisyy Hole cleaning analysis
ApplicationsAll Drilling Environments
Featuresyy Focused, real-time, offsite 24-hour monitoring and
analysis of datayy Integrated drilling advice through wellsite, operator,
and remote support teamsyy Structured workflow and proactive
communication protocolsyy Pre-well and Post-well service analysis
CoPilot™
Real-time drilling performance service
Applicationsyy Deep wateryy Extended reach drillingyy Challenging interbedded or complex well formationsyy Conventional/unconventional oil and gasyy Salt drillingyy Shale gas drilling
Featuresyy Real-time data transmission and expert interpretationyy Bending moment and bending orientationyy Accurate downhole weight and torqueyy Downhole dynamics measurements including whirl
Tool size
4¾-in. (121 mm)6¾-in. (171 mm) 8¼-in. (210 mm) 9½-in. (241 mm)
Hole size 5¾-in. to 26-in. (146 mm to 660 mm)
DRILLING SERVICES Formation Evaluation Technologies
OnTrak™
Integrated MWD service
MagTrak™
Magnetic resonance service
AziTrak™
Deep azimuthal resistivity tool
Applicationsyy Offshore exploration and development yy Complex directional targetsyy Geosteering
Featuresyy Azimuthal gamma ray with imaging capabilityyy High-frequency phase resistivityyy Low-frequency attenuation resistivityyy Fast two-way communication between the surface
and downhole
Applicationsyy Deep water drillingyy Extended-reach drilling yy Reservoirs with complex or mixed lithologyyy Low resistivity contrast reservoirs
Featuresyy Accurate T2 magnetic resonance logsyy Minimizes motion effects on measurements induced
by drilling vibrationyy Sourceless porosityyy Real-time T2 spectrum transmitted to surface
Applicationsyy Conventional oil and gas reservoirsyy Deep water drillingyy High-angle and horizontal wellsyy Brownfield production enhancementyy Field development through infill drilling
Featuresyy Compact, fully integrated sub featuring
close-to-the-bit measurementsyy Close-to-the-bit, deep-reading azimuthal resistivity
allows early detection of remote conductive boundaries yy Intuitive, dynamic, real-time display of
reservoir boundaries
Tool size
4¾-in. (121 mm)6¾-in. (172 mm)8¼-in. (210 mm)9½-in. (241 mm)
Hole size* 5¾-in. to 26-in. (146 mm to 669 mm)
Tool size4¾-in. (121 mm)6¾-in. (172 mm)8¼-in. (211 mm)
Hole size 5¾-in. to 12¼-in. (146 mm to 314 mm)
Tool size 4¾-in. (121 mm)6¾-in. (172 mm)
Hole size 5¾-in. to 105⁄8-in. (146 mm to 270 mm)
LithoTrak™
Density and porosity service
Applicationsyy Formation and reservoir evaluation in all well profilesyy Reservoir navigationyy Wellbore stability monitoring
Featuresyy Acquires data using straight hole rotary, steerable
motors, or rotary steerable drilling systems yy Measurements are collected by a standoff binning
process to provide accurate, compensated density and Pe values
yy Real-time borehole density images and caliper measurements in all mud types
yy Accurate identification of fluid contacts and hydrocarbon typing
yy Azimuthal borehole caliper and real-time, short-spaced borehole images
Tool size4¾-in. (121 mm)6¾-in. (171 mm)8¼-in. (241 mm)
Hole size* 57⁄8-in. to 12¼-in. (149 mm to 311 mm)
© 2017 Baker Hughes, a GE company, LLC – All rights reserved.
Baker Hughes, a GE company, LLC and its affiliates (“BHGE”) provides this information on an “as is” basis for general information purposes and believes it to be accurate as of the date of publication. BHGE does not make any representation as to the accuracy or completeness of the information and makes no warranties of any kind, specific, implied or oral, to the fullest extent permissible by law, including those of merchantability and fitness for a particular purpose or use. BHGE hereby disclaims any and all liability for any direct, indirect, consequential or special damages, claims for lost profits, or third party claims arising from the use of the information, whether a claim is asserted in contract, tort, or otherwise. The BHGE logo is a trademark of Baker Hughes, a GE company, LLC. GE and the GE monogram are trademarks of General Electric Company used under trademark license.
67259
bhge.com
VisiTrak™
Geospatial Navigation and Analysis Service
Applicationsyy Onshore / Offshore yy Deepwateryy Conventional Oil & Gasyy SAGDyy Pilot hole mitigationyy Highly deviated, horizontal and extended reach wellsyy Reservoir Navigation / Geosteering and reservoir
mapping
Featuresyy Low frequency measurements for extra deep
resistivity measurements yy Cross component antenna technology allowing
azimuthal sensitivityyy Early reservoir detection from overburden yy Multiple boundary / fluid contact detection yy Real-time - reservoir architecture mapping to
seismic scale
Tool size 6¾-in. (172 mm)9½-in. (241 mm)
Hole size 8½-in. to 12¼-in. (216 mm to 311 mm)
ZoneTrak™ RAt-bit resistivity service
Applicationsyy Casing and coring point selectionyy Salt exit detectionyy Real-time pressure managementyy Geo-stoppingyy All drilling environmentsyy High-resistivity contrast formations
Featuresyy Identifies top and bottom of reservoiryy Detects formation changes faster to adjust drilling
fluid parametersyy Includes forward response modelingyy Real-time data transmitted through BHGE
WellLink™ service
Tool size 6¾-in. (172 mm)9½-in. (241 mm)
Hole size 83⁄8-in. to 18¼-in. (213 mm to 464 mm), dependent upon mud type
ZoneTrak™ GNear-bit gamma service
Applicationsyy Casing and coring point selectionyy Geo-stopping yy Reservoir navigation yy All drilling environments
Featuresyy True azimuthal gamma ray measures 6 feet above
the bityy Imaging capabilitiesyy Two gamma sensors yy Real-time gamma data can be displayed through BHGE
WellLink™ service
Tool size4¾-in. (121 mm)6¾-in. (172 mm)9½-in. (241 mm)
Hole size 5¾-in. to 18¼-in. (146 mm to 464 mm)
StarTrak™
Electrical imaging service
Applicationsyy Complex or thin-bedded reservoirsyy Shale gas playsyy Geosteeringyy Wellbore stability
Featuresyy Acquires high-resolution images at penetration rates
up to 150 ft/hryy Very tolerant of moderate levels of stick/slip yy Real-time images displayed through BHGE
WellLink™ serviceyy Detailed fracture analysis
Tool size 4¾-in. (121 mm)6¾-in. (172 mm)
Hole size 5¾-in. to 9½-in. (146 mm to 241 mm)
SoundTrak™ Acoustic service
SeismicTrak™
Seismic-while-drilling service
Applicationsyy Pore-pressure predictionyy Acoustic slowness in large holes and slow formationsyy Seismic time-depth tieyy Acoustic porosity evaluationyy Early detection of shallow gasyy Acoustic light hydrocarbon indicator
Featuresyy Proprietary quadrupole transmitter technology yy Multi-frequency sourceyy Measures compressional and shear slownessyy Salinity-independent measurements for real-time
pore-pressure prediction yy Real-time geomechanical rock properties measured for
wellbore stabilityyy High attenuation, band-reject isolatoryy Sourceless porosity
Applicationsyy Deep water drillingyy Vertical, Highly deviated, horizontal, or
extended-reach wellsyy Determining casing and coring pointsyy Reducing seismic uncertaintyyy Identify over-pressured zones below the bit
Featuresyy Measurements acquired during natural breaks in
the drilling processyy Reduces overall cost of logging programyy Employs precise clock mechanisms for highly accurateyy Precise clock mechanisms for highly accurate
check-shot time-depth pairsyy Immediate data-capture feedback during
drilling processyy Rugged design with redundant sensors and
large memory
Tool size6¾-in. (172 mm)8¼-in. (210 mm)9½-in. (241 mm)
Hole size 57⁄8-in. to 26-in. (150 mm to 660 mm)
TesTrak™
Formation pressure while-drilling service
FASTrak™
Fluid analysis, sampling and testing service
Applicationsyy Onshore and offshore drilling: all well types and
formation typesyy Drilling hazard mitigationyy Reservoir characterization
Featuresyy SmarTest™ intelligent testingyy SmartPad™ closed-loop sealingyy Real-time pore pressure measurements yy Real-time gradient analysis to identify fluids
and contacts yy Real-time formation mobility
Applicationsyy Single-phase fluid sampling and
formation-pressure testingyy Reservoir knowledge enhancement, drilling efficiency
and operational safetyyy Onshore / Offshoreyy Deepwateryy Highly deviated, extended reach and
horizontal wells
Featuresyy SmarTest™ intelligent testingyy SmartPad™ closed-loop sealingyy Multiple drawdowns per test station yy Real Time Fluid Analysisyy Direct measurement of Density, Viscosity, Refractive
Index and Soundspeedyy Sampling and Pressure Testing while circulatingyy High Accuracy Pump Controlyy Compressibility and Drawdown Mobilityyy Capture of up to 16 Single Phase Samplesyy Multiple samples per pressure stationyy Chemical Resistant metallurgyyy Single Phase Sample Tank Technology
Tool size 6¾-in. (171 mm)9½-in. (241 mm)
Hole size 83⁄8-in. to 26-in. (213 mm to 660 mm)
Nominal hole size
8½-in. to 12¼-in. (216 mm to 311.2 mm)
Tool size4¾-in. (121 mm)6¾-in. (171 mm)8¼-in. (210 mm)
Hole size 5¾-in. to 17½-in. (146 mm to 445 mm)
Tool size 6¾-in. (172 mm)
Hole size 8½-in. to 11¾- in. (216 mm to 298 mm)
aXcelerate™ PLUSHigh-speed mud-pulse telemetry service
Wired-Pipe Telemetry
Applicationsyy Critical wellsyy Geosteering and optimized wellbore placementyy Extended-reach and complex 3D wellsyy Performance drillingyy Required for extended formation evaluation BHA’s
Featuresyy Downhole adjustable pulser setup via downlinkyy Real-time formation evaluation data for
reservoir navigationyy High-resolution downhole drilling dynamics data yy Bandwidth up to 40 bits per second physical and up to
256 bits per second compressed
Applicationsyy Extended-reach wellsyy Underbalanced drillingyy Geosteeringyy Performance drillingyy Required for extended formation evaluation BHA’syy Enabling technology for delivering
measurements along the string
Featuresyy Real-time formation evaluation memory quality data for
reservoir navigationyy Bandwidth up to 57,600 bits per secondyy High-resolution downhole drilling dynamics data of the
BHA and optional along the stringyy Drilling in environments where data transmission was
not possible with mud pulse telemetry
Tool size 4¾-in. (121 mm)6¾-in. (172 mm)
Hole size 5¾-in. to 105⁄8-in. (146 mm to 270 mm)
Tool size
4¾-in. (121 mm)6¾-in. (171 mm)8¼-in. (210 mm)9½-in. (241 mm)
Hole size 5¾-in. to 26-in. (146 mm to 660 mm)
Conventional Coring
JamBuster™
Jam mitigation coring system
HydroLift™
Full closure catcher coring system
LaserCut™ Quick access coring system
Applicationsyy Onshore / Offshore drillingyy Conventional and Unconventional formationsyy High Pressure / High Temperature formationsyy Shale Gas, Deep Water & Geothermal Drillingyy Horizontal and deviated Drillingyy Consolidated and Unconsolidated formations
Featuresyy HT-Series (Heavy Duty, High Torque) Core Barrelsyy BHGE Core Bits yy CoreGard™ Low Invasion Technology yy Disposable, vented Inner Barrels yy Non Rotating Inner Tube Stabilizers
Applicationsyy Onshore / Offshore drillingyy Conventional and Unconventional formationsyy High Pressure / High Temperature formationsyy Shale Gas, Deep Water & Geothermal Drillingyy Horizontal and deviated Drillingyy Consolidated and fractured formations
Featuresyy Telescoping Sleeves allow continuous coring after
jamming inside Inner Barrelyy Modular Coring System
Applicationsyy Recovery of unconsolidated formation materialyy HydroLift is available for the HT30 and HT60 core
barrels, cutting 4 and 5¼-inch diameter core samples, respectively
yy The System also includes a slick entry feature that prevents fractured core from catching or jamming into the catcher
Featuresyy Full closure catcher completely seals the inner barrelyy Slick, unobstructed core entry yy Back-up conventional core catcher
Applicationsyy Onshore / Offshore drillingyy Conventional and Unconventional formationsyy Shale Gas, Deep Water & Geothermal Drillingyy Horizontal and deviated Drilling
Featuresyy Integral, one piece liners with LaserCut along its lengthyy Rapid access on surfaceyy Utilizes conventional equipment
Tool Description Core Size
Tool Size
HT10: 4¾-in. (120.6 mm)HT12: 51⁄8-in. (130.2 mm)250P: 5½-in. (139.7 mm)250P: 6¼-in. (158.7 mm)HT30: 6¾-in. (171.4 mm)
HT30 Max: 7¼-in. (184.2 mm)HT40: 8-in. (203.2 mm)
HT60: 9½-in. (241.3 mm)Large Core HT60
25⁄8-in. (66.7mm)3-in. (76.2mm)
3½-in. (76.2mm)4-in. (101.6mm)4-in. (101.6mm)
4½-in. (114.3mm)4¾-in. (120.6mm)5¼-in. (133.4mm)6-in. (152.4mm)
Hole Size 5¾-in. to 17½-in. + (146.0 - 444.5 mm +)
Tool Description Core Size
Tool Size
HT10: 4¾-in. (120.6mm)HT12: 51⁄8-in. (130.2 mm)HT30: 6¾-in. (171.0 mm)
HT30 Max: 7¼-in. (184.2 mm)HT40: 8-in. (203.2 mm)
HT60: 9½-in. (241.3 mm)
21⁄8-in. (54.0mm)2½-in. (63.5mm)3½-in. (88.9mm)4-in. (101.6mm)
4¾-in. (120.6mm)5¼-in. (133.4mm)
Hole Size 5¾-in. to 17½-in. + (146.0 mm to 444.5 mm +)
Tool Description Core Size
Tool Size
HT30: 6¾-in. (171.0 mm)HT60: 9½-in. (241.3 mm)
4-in. (101.6mm)5¼-in. (133.4mm)
Hole Size 8½-in. to 17½-in. + (146.0 - 444.5 mm) +
Tool Description Core Size
Tool Size
HT12: 51⁄8-in. (130.2 mm)HT30: 6¾-in. (171.0 mm)
HT30 Max: 7¼-in. (184.2 mm)
2½-in. (63.5 mm)3½-in. (88.9.6 mm)
4-in. (101.6 mm)
Hole Size 61⁄8-in. to 17½-in. + (155.6 mm to 444.5 mm +)
CoreGel™
Downhole core encapsulation system
Applicationsyy Onshore / Offshore yy Conventional and Unconventional formationsyy Horizontal and deviated Drilling
Featuresyy Encapsulates cores in a viscous, noninvasive,
protective gelyy Increases core integrity during cuttingyy Helps prevent jammingyy Reduces drilling fluid contamination
Tool Description Core Size
Tool Size
HT30: 6¾-in. (171.0mm)HT60: 9½-in. (241.3mm)
4-in. (101.6mm)5¼-in. (133.4mm)
Hole Size 8½-in to 17½-in. (215.9 to 444.5mm)
SOr™
Sponge liner coring system
Applicationsyy Specialized Coring operationsyy All Drilling Environmentsyy Enhanced oil recovery projectsyy Consolidated formations
Featuresyy Molded, oil-absorptive sponge lineryy Foam reinforced webbingyy LaserCut aluminum liner system yy Proprietary pressure-compensating piston design
Tool Description Core Size
Tool Size HT30: 6¾-in. (171.0mm) 3½-in (76.2mm)
Hole Size 8½-in. (215.9mm)
Core BitsApplicationsyy Onshore / Offshore drillingyy Conventional and Unconventional formationsyy Extremely hard and abrasive formationsyy Unconsolidated formationsyy Highly fractured formationsyy Shale Gas, Deep Water and Geothermal Drillingyy Horizontal and deviated Drillingyy Enhanced Oil Recovery Projects, specialized SOr Sponge
Precision Core Bits
Featuresyy Talon Series PDC Core Bitsyy IRev Impregnated Core Bitsyy Natural Diamond Core Bits
Tool size 4¾-in. to 9½-in. (120.6 mm to 241.3 mm)
Hole size 5¾-in. to 17½-in. + (146.0 mm to 444.5 mm +)
Oriented Coring Services*
Tool Description Core Size
Tool Size
HT10: 4 ¾-in. (120.6mm)HT12: 5 1
8-in. (130.2mm)HT30: 6 ¾-in. (171.0mm)
HT30 Max: 7 ¼-in. (184.2mm)HT40: 8-in. (203.2mm)
HT60: 9 ½-in. (241.3mm)
2 5⁄8-in (66.7mm) 3 -in (76.2mm)4 -in (101.6mm)
4 ½-in (114.3mm)4 ¾-in (120.6mm)5 ¼-in (133.4mm)
Hole Size 5 ¾-in to 17 ½-in. + (146.0 - 444.5mm +)
* BHGE will only provide the needed interface to the survey tools
Applicationsyy Onshore / Offshore yy Conventional and Unconventional formationsyy Consolidated formations
Featuresyy Knives in shoe assembly continuously scribe the coreyy Oriented tools in the core barrel and survey tool
rotationally coupledyy Identifies the core’s in situ orientation
FE-Vision™
Cuttings and Gas Evaluation Services
Vision ServicesWellsite and remote formation evaluation
HC-Vision™
Reservoir Characterization Services
CI-Vision™
Carbon Isotope Analysis
TRU-Vision™
Quantitative Gas Extraction and Analysis
STRATA-Vision™
Advanced Cuttings Evaluation
ApplicationsAll Drilling Environments
Featuresyy Gas sample collection and analysis of
Methane- Pentane gassesyy Cuttings sample collection and lithology analysisyy Provides integrated data visualization yy Identification of potential hydrocarbon presence
ApplicationsAll Drilling Environments
Featuresyy Provides visual reservoir interpretation logsyy Provides indications of hydrocarbon porosity,
permeability, volumetrics, saturations, geohazards and fluid compartmentalization
yy Processes data from current drilling projects and legacy projects independent of SLS provider
yy Integrates with other formation evaluation services
ApplicationsAll Drilling Environments
Featuresyy Continuous C1-C3 and CO2 Carbon Isotope ratio analysisyy Provides insight of source rock, maturity, transition
zones and connectivityyy Indicators to biogenic, thermogenic or mixed gas
and their originyy Purpose built, rack mounted lab quality equipment
ApplicationsAll Drilling Environments
Featuresyy Quantitative analysis of C1-C8 organic hydrocarbons and
key inorganic gassesyy Heated quantitative gas extraction yy Constant flow and constant temperatureyy Continuous quantification and visualization of
mud density yy Automated and continuous gas extraction efficiency
Applicationsyy Unconventional wellsyy Extended-reach and horizontal wellsyy Slimhole drilling yy HPHT zones
Featuresyy Formation evaluation log correlation with other
FE datasetsyy Identification of productive zones yy Chemostratigraphic profile and surface
spectral - gammayy Near real-time formation and kerogen
geochemical analysis