7/29/2019 Exploration Network Chapter 10 (Rev 1.0)
1/25
2007 Cisco Systems, Inc. All rights reserved. Cisco Public
ITE PC v4.0
Chapter 1 1
Planning and Cabling
Networks
Network Fundamentals Chapter 10
7/29/2019 Exploration Network Chapter 10 (Rev 1.0)
2/25
ITE PC v4.0
Chapter 1 2 2007 Cisco Systems, Inc. All rights reserved. Cisco Public
Choosing the Appropriate LAN Device Given a network requirement, determine the optimum
number of sub networks in the larger internetwork.
7/29/2019 Exploration Network Chapter 10 (Rev 1.0)
3/25
ITE PC v4.0
Chapter 1 3 2007 Cisco Systems, Inc. All rights reserved. Cisco Public
Choosing the Appropriate LAN Device
7/29/2019 Exploration Network Chapter 10 (Rev 1.0)
4/25
ITE PC v4.0
Chapter 1 4 2007 Cisco Systems, Inc. All rights reserved. Cisco Public
Device Selection Factors
7/29/2019 Exploration Network Chapter 10 (Rev 1.0)
5/25
ITE PC v4.0
Chapter 1 5 2007 Cisco Systems, Inc. All rights reserved. Cisco Public
Factors to Consider in Choosing a Switch
The cost of a switch is determined by its capacity andfeatures.
The apparent cost savings of using a single switch maybe offset by the expense from the longer cable lengths
required to connect every device on the LAN to oneswitch.
Another cost consideration is how much to invest inredundancy.
Redundancy allows the physical network to continue itsoperation even if one device fails.
7/29/2019 Exploration Network Chapter 10 (Rev 1.0)
6/25
ITE PC v4.0
Chapter 1 6 2007 Cisco Systems, Inc. All rights reserved. Cisco Public
Factors Determining LAN Switch Selection
7/29/2019 Exploration Network Chapter 10 (Rev 1.0)
7/25ITE PC v4.0
Chapter 1 7 2007 Cisco Systems, Inc. All rights reserved. Cisco Public
Factors to Consider in Router Selection
7/29/2019 Exploration Network Chapter 10 (Rev 1.0)
8/25ITE PC v4.0
Chapter 1 8 2007 Cisco Systems, Inc. All rights reserved. Cisco Public
LAN Cabling Areas
.
7/29/2019 Exploration Network Chapter 10 (Rev 1.0)
9/25ITE PC v4.0
Chapter 1 9 2007 Cisco Systems, Inc. All rights reserved. Cisco Public
LAN Cabling AreasAreas are limited to a maximum distance of 100 meters
per channel.
UTP patch cords used to connect devices to the walljacks have a maximum length of 10 meters.
The telecommunications room is where connections tointermediary devices take place and sometimes housesnetwork servers.
The maximum length for a cable from a terminationpoint in the telecommunication room to the terminationat the work area outlet must not exceed 90 meters.
Backbones typically require high bandwidth media suchas fiber-optic cabling.
7/29/2019 Exploration Network Chapter 10 (Rev 1.0)
10/25ITE PC v4.0
Chapter 1 10 2007 Cisco Systems, Inc. All rights reserved. Cisco Public
Cable LengthAttenuation - reduction of the strength of a signal
as it moves down a media. The longer the media,the more attenuation will affect the signal.
Cabling distance is a significant factor in data
signal performance. Signal attenuation andexposure to possible interference increase withcable length.
7/29/2019 Exploration Network Chapter 10 (Rev 1.0)
11/25ITE PC v4.0
Chapter 1 11 2007 Cisco Systems, Inc. All rights reserved. Cisco Public
Ease of Installation
7/29/2019 Exploration Network Chapter 10 (Rev 1.0)
12/25ITE PC v4.0
Chapter 1 12 2007 Cisco Systems, Inc. All rights reserved. Cisco Public
RJ-45 T568A and T568B Termination
Tx: Pins 1 and 2; Rx: Pins 3 and 6
7/29/2019 Exploration Network Chapter 10 (Rev 1.0)
13/25
ITE PC v4.0
Chapter 1 13 2007 Cisco Systems, Inc. All rights reserved. Cisco Public
Straight-through Cables Use straight-through cables for these connections:
Switch to a router Ethernet port, Computer to switch,Computer to hub
7/29/2019 Exploration Network Chapter 10 (Rev 1.0)
14/25
ITE PC v4.0
Chapter 1 14 2007 Cisco Systems, Inc. All rights reserved. Cisco Public
Crossover UTP Cables
Use crossover cables for these connections: Switch/Hub toSwitch/Hub, Router to router Ethernet port connection, Computerto computer, Computer to a router Ethernet port
7/29/2019 Exploration Network Chapter 10 (Rev 1.0)
15/25
ITE PC v4.0
Chapter 1 15 2007 Cisco Systems, Inc. All rights reserved. Cisco Public
Types of WAN Connections
7/29/2019 Exploration Network Chapter 10 (Rev 1.0)
16/25
ITE PC v4.0
Chapter 1 16 2007 Cisco Systems, Inc. All rights reserved. Cisco Public
WAN Connections - Serial
7/29/2019 Exploration Network Chapter 10 (Rev 1.0)
17/25
ITE PC v4.0
Chapter 1 17 2007 Cisco Systems, Inc. All rights reserved. Cisco Public
Serial DTE and DCE WAN Connections In our labs, when the local router is required to provide
the clock rate, a DCE cable will be used.
By assigning a clock rate to the router, a router adjuststhe speed of its communication operations, thereby
synchronizing with the devices connected to it.
7/29/2019 Exploration Network Chapter 10 (Rev 1.0)
18/25
ITE PC v4.0
Chapter 1 18 2007 Cisco Systems, Inc. All rights reserved. Cisco Public
Lab Approach
7/29/2019 Exploration Network Chapter 10 (Rev 1.0)
19/25
ITE PC v4.0
Chapter 1 19 2007 Cisco Systems, Inc. All rights reserved. Cisco Public
Determining the Number of Hosts To develop an addressing scheme for a network,
determine the total number of hosts. Consider everydevice that will require an IP address, now and in thefuture.
End devices require an IP address: Computers,Servers, Printers, IP phones, and IP cameras
Network devices requiring an IP address: Router LANand WAN (serial) interfaces
Network devices requiring an IP address formanagement : Switches and Wireless Access Points
Recall that the number of hosts on one network orsubnet: 2^n 2, n = number of host bits
7/29/2019 Exploration Network Chapter 10 (Rev 1.0)
20/25
ITE PC v4.0
Chapter 1 20 2007 Cisco Systems, Inc. All rights reserved. Cisco Public
Reasons for Dividing a Network into Subnets
Manage Broadcast Traffic
Different Network Requirements
Security
Each subnet, as a physical network segment, requiresa router interface as the gateway for that subnet. Eachconnection between routers is a separate subnet.
Counting number of subnets: 2^n; n = number ofsubnet bits (stolen host bits)
7/29/2019 Exploration Network Chapter 10 (Rev 1.0)
21/25
ITE PC v4.0
Chapter 1 21 2007 Cisco Systems, Inc. All rights reserved. Cisco Public
Designing the Address Standard forInternetwork
When allocating an IP address to a router interface thatis the gateway for a LAN, it is common practice to usethe first (lowest) or last (highest) address within thesubnet range.
When assigning addresses to devices that manageother devices, using a consistent pattern within asubnet makes these addresses easily recognizable.
Remember to document your IP addressing scheme on
paper.
7/29/2019 Exploration Network Chapter 10 (Rev 1.0)
22/25
ITE PC v4.0
Chapter 1 22 2007 Cisco Systems, Inc. All rights reserved. Cisco Public
IP Address Allocation Methods Variable Length Subnet Masking (VLSM), - one assigns
the prefix and host bits to each network based on thenumber of hosts in that network.
Non-VLSM approach, where all subnets use the same
prefix length and the same number of host bits. Students are encouraged to comprehend the
Calculating Address Cases on this chapter.
7/29/2019 Exploration Network Chapter 10 (Rev 1.0)
23/25
ITE PC v4.0
Chapter 1 23 2007 Cisco Systems, Inc. All rights reserved. Cisco Public
Device Interfaces
7/29/2019 Exploration Network Chapter 10 (Rev 1.0)
24/25
ITE PC v4.0
Chapter 1 24 2007 Cisco Systems, Inc. All rights reserved. Cisco Public
Device Management Connection
7/29/2019 Exploration Network Chapter 10 (Rev 1.0)
25/25
ITE PC 4 0