FE8113 ”High Speed Data Converters”
Part 2: Digital background calibration
J.Keane et.al: “Background Interstage Gain Calibration Technique for Pipelined ADCs”, IEEE Transactions on Circuits and Systems-I: Regular Papers, Vol. 52,No. 1, January 2005, pp 32-43
J.Li, U-K.Moon: “Background Calibration Techniques for Multistage Pipelined ADCs With Digital Redundancy”, IEEE Transactions on Circuits and Systems-II: Analog and Digital Signal Processing, Vol. 50, No. 9, September 2003, pp 531-538
Papers 5 and 6
J.Keane et.al: “Background Interstage Gain Calibration Technique for Pipelined ADCs”
Outline: A background self-calibration technique is proposed that can correct both linear and nonlinear errors in the inter-stage amplifiers of pipeline and algorithmic ADCs. Simulations show that the proposed algorithm yields a 72dB SNDR and a 112dB SFDR for a 12-bit pipeline. The calibration tracking time constant is approximately 8*105
samples
J.Keane et.al: “Background Interstage Gain Calibration Technique for Pipelined ADCs”
Ideal N-bit ADC with input range (-Vref, Vref)
Assuming an ideal stage DASC, and an interstage gain of G1, the ADC output is calculated by:
The interstage gain G1 and the M ADSC levels must satisfy the condition M≥G1 to prevent the backend from overloading. Typically, M>G1, introducing redundancy with digital correction. The primary remaining error sources are errors in the interstage amplifier and nonmlinearity in the DASC. In a switch-cap stage, DASC nonlinearity results primarily from capacitor mismatch and can be measured and corrected for separately, as presented by Galton. The remaining error source is the interstage amplifier, and the paper describes how gain error and nonlinearity in these can be measured an corrected for.
J.Keane et.al: “Background Interstage Gain Calibration Technique for Pipelined ADCs”
Correction of gain errors, two approaches:
I:
II:
J.Keane et.al: “Background Interstage Gain Calibration Technique for Pipelined ADCs”
With DASC output VDASC=K1D1Vref,where K1 1 is the DASC gain, theInput of a pipeline stage is
a)
b)
c)
J.Keane et.al: “Background Interstage Gain Calibration Technique for Pipelined ADCs”
Equivalent model of pipeline stage
Output word:
where
J.Keane et.al: “Background Interstage Gain Calibration Technique for Pipelined ADCs”
Interstage gain estimation
Allow at least two D1 levels for a given input
The output is then
J.Keane et.al: “Background Interstage Gain Calibration Technique for Pipelined ADCs”
Define:
Then:
Multiply z by R:
If R is a pseudorandom sequence with zero mean, then RI(y0) will have zero mean. ThenE[Rz]=e, which is proportional to
Rz can be considered a noisy estimate of the error coefficient and used to adjust this:
J.Keane et.al: “Background Interstage Gain Calibration Technique for Pipelined ADCs”
Equivalent model of pipeline stage including amplifier nonlinearity
(Weakly nonlinear)
Modified correction algorithm
Assuming ideal backend
Rewriting and simplifying
Assume
Adding test sequence
where
J.Keane et.al: “Background Interstage Gain Calibration Technique for Pipelined ADCs”
Z written in general form
where
Multiplying by R
Comparing samples where Is small to those where
is large gives an estimate of b1 independent of m1
However, this is depentent on backend behaviour. This means that tracking speed issignal dependent
J.Keane et.al: “Background Interstage Gain Calibration Technique for Pipelined ADCs”
Another technique that does nor rely on specific backend codes is presented.By calculating covariance betrween Rz and
where
J.Keane et.al: “Background Interstage Gain Calibration Technique for Pipelined ADCs”
Update equation
Integrating over a large number of samples
J.Keane et.al: “Background Interstage Gain Calibration Technique for Pipelined ADCs”
J.Keane et.al: “Background Interstage Gain Calibration Technique for Pipelined ADCs”
Correction of backend errors
J.Keane et.al: “Background Interstage Gain Calibration Technique for Pipelined ADCs”
Example implementation
J.Keane et.al: “Background Interstage Gain Calibration Technique for Pipelined ADCs”
J.Keane et.al: “Background Interstage Gain Calibration Technique for Pipelined ADCs”
J.Keane et.al: “Background Interstage Gain Calibration Technique for Pipelined ADCs”
J.Keane et.al: “Background Interstage Gain Calibration Technique for Pipelined ADCs”
J.Keane et.al: “Background Interstage Gain Calibration Technique for Pipelined ADCs”
J.Li, U-K.Moon: “Background Calibration Techniques for Multistage Pipelined ADCs With Digital Redundancy
”
Outline: The proposed digital background calibration scheme, applicable to multistage ADCs, corrects the linearity errors resulting from capacitor mismatches and finite opamp gain. The calibration is achieved by recalculating the digital output based on each stage’s equivalent radix. The equivalent radices are extracted in the background by using a digital correlation method. The calibration technique takes advantage of the digital redundancy architecture inherent to most pipelined ADCs. The SNR is not degraded from the pseudorandom noise sequence injected into the system
J.Li, U-K.Moon: “Background Calibration Techniques for Multistage Pipelined ADCs With Digital Redundancy
”
Introduction- Correlation-based background digital calibration scheme in the context of a 1.5b-per-stage pipelined or cyclic ADC- The input signal need not be reduced to allow the injection of
pseudorandom calibration signal- Minimal addition of analog hardware for calibration
J.Li, U-K.Moon: “Background Calibration Techniques for Multistage Pipelined ADCs With Digital Redundancy
”Capacitor flip-over MDAC
J.Li, U-K.Moon: “Background Calibration Techniques for Multistage Pipelined ADCs With Digital Redundancy
”
For cyclic:
Error sources
J.Li, U-K.Moon: “Background Calibration Techniques for Multistage Pipelined ADCs With Digital Redundancy
””Non-capacitor-flip-over” MDAC
J.Li, U-K.Moon: “Background Calibration Techniques for Multistage Pipelined ADCs With Digital Redundancy
”
Rearranging error terms forcapacitor flip-over MDAC
J.Li, U-K.Moon: “Background Calibration Techniques for Multistage Pipelined ADCs With Digital Redundancy
”Test signal injection
J.Li, U-K.Moon: “Background Calibration Techniques for Multistage Pipelined ADCs With Digital Redundancy”
Suggested implementaion of test signal injection
J.Li, U-K.Moon: “Background Calibration Techniques for Multistage Pipelined ADCs With Digital Redundancy”
Interference Cancelling
J.Li, U-K.Moon: “Background Calibration Techniques for Multistage Pipelined ADCs With Digital Redundancy”
Interference Cancelling
J.Li, U-K.Moon: “Background Calibration Techniques for Multistage Pipelined ADCs With Digital Redundancy”
Interference Cancelling
J.Li, U-K.Moon: “Background Calibration Techniques for Multistage Pipelined ADCs With Digital Redundancy”
Interference Cancelling
J.Li, U-K.Moon: “Background Calibration Techniques for Multistage Pipelined ADCs With Digital Redundancy”
Simulation results