1
www.fontaineintermodal.comFor service call 205-385-0451
To order parts call: 866-382-7278
Fontaine Evolution® Intermodal Flat Deck
Owner’s Guide• Important Information• Operator Instructions• Troubleshooting• Maintenance• Replacement Parts
2
www.fontaineintermodal.comFor service call 205-385-0451
To order parts call: 866-382-7278
Contents
Section 1 - Important InformationImportant Information .............................................................................................. 3Operating Limits and Restrictions ............................................................................ 4 Required Decals ...................................................................................................... 5Load Securement .................................................................................................... 8
Section 2 - Arm Operation InstructionsIntroduction ........................................................................................................... 11Getting Started ...................................................................................................... 12 Moving Arms Flat to Upright .................................................................................. 14 Positioning Arms for Loading ................................................................................. 15 Positioning Arms Flat for empty transit ................................................................... 16 Stacking three-high or four-high for repositioning ................................................... 17
Section 3 - TroubleshootingArm Alignment ....................................................................................................... 18
Section 4 - MaintenancePreventive Maintenance ......................................................................................... 20
Section 5 - Replacement PartsReplacement Parts ...........................................................................................24-45
Appendix AEvolution Axle/Hub Bolt Installation/Tightening/Maintenance ............................46-54
Read this manual carefully and completely before operating or performing maintenance on your Fontaine Evolution flat deck. If you have any questions regarding your Fontaine Evolution please contact Fontaine Intermodal 205-385-0451.
3
www.fontaineintermodal.comFor service call 205-385-0451
To order parts call: 866-382-7278
Preventive Maintenance. It is important that every owner and/or operator have an organized Preventive Maintenance program (PMP). The United States Department of Transportation requires by law that maintenance records be kept on every commercial highway vehicle. It is to your advantage to be able to show that regularly scheduled inspection checks have been made on every piece of equipment operated.
A regular maintenance program will not only assure that you will get the most usage from your equipment, but it will also assist in demonstrating that your equipment has been properly maintained.
You can get help setting up and operating a preventive maintenance program by sending for a “Maintenance Manual for Trailers and Containers”. Contact the Truck Trailer Manufacturers Association, 1020 Princess Street, Alexandria, Virginia 22314.
This manual has been prepared to assist you in the safe operation and maintenance of your Fontaine Evolution intermodal flat deck. It contains important information on proper use.
Operator instructions are provided for assistance in the proper operation of your Evolution. Specific component operating instructions and your company’s procedures should be consulted. These may include DOT and employer training programs or instructions. This manual includes safety checks and procedures the operator must perform. As with all heavy equipment, it is very important to follow all customary safety processes and procedures.
Important Information
Section 1 - Important Information
WARNINGTHIS SYMBOL IS USED THROUGHOUT THIS MANUAL TO CALL ATTENTION TO THE PROCEDURES YOU MUST FOLLOW EXACTLY. CARELESSNESS OR FAILURE TO FOLLOW INSTRUCTIONS MAY LEAD TO DEATH OR SERIOUS INJURY.
CAUTIONTHIS SYMBOL INDICATES A PROCEDURE YOU MUST FOLLOW EXACTLY OR DAMAGE TO COMPONENTS OR EQUIPMENT MAY OCCUR. SERIOUS PERSONAL INJURY MAY ALSO RESULT FROM FAILURE TO FOLLOW THIS PROCEDURE.
NOTETHIS SYMBOL IS USED THROUGHOUT THIS MANUAL TO CALL ATTENTION TO OPERATIONS, PROCEDURES AND INSTRUCTIONS THAT ARE IMPORTANT FOR PROPER SERVICE. IT MAY ALSO INDICATE INFORMATION THAT CAN MAKE SERVICE QUICKER OR EASIER.
IMPORTANTRead this manual carefully. Should you have any questions, contact a FONTAINE factory
representative immediately.
1-205-385-0451
For Warranty and Parts call1-866-382-7278
This manual should be kept with the trailer in digital or printed form at all times and should
remain with the trailer when it is sold. A digital file is available at
www.fontaineintermodal.com/manual
4
www.fontaineintermodal.comFor service call 205-385-0451
To order parts call: 866-382-7278
Concentrated load capacity: 48,000 lbs in 4 ft
Distributed load capacity: 80,000 lbs in 53 ft
Stacking height: 162"
CAUTIONDURING EMPTY REPOSITIONING, IT IS THE DRIVER’S RESPONSIBILITY TO MAKE SURE THAT THE HEIGHT OF CHASSIS PLUS DECK AT ITS HIGHEST POINT IS LESS THAN 162" (13' 6").
Overall deck height: 27.5" (with arms down)
Width: The overall width of the deck and arms is 102". All intermodal loads should not exceed this width or have excess hanging from either side of the deck (this includes timbers).
Length: The overall length of the deck is 53 ft. All intermodal loads should not exceed this length or have excess hanging from either end of the deck.
CAUTIONTIMBERS OR DUNNAGE LONGER THAN 96" (OR SHORTER DUNNAGE WITHIN THE PATH OF THE ARMS) WILL INTERFERE WITH THE UP AND DOWN OPERATION OF THE ARMS.
Operating Limits And Restrictions
Section 1 - Important Information (continued)
5
www.fontaineintermodal.comFor service call 205-385-0451
To order parts call: 866-382-7278
WARNINGWhen securing cargo, follow DOTguidelines 49 CFR section 393.100 to393.136 - Protection Against shifting andfalling cargo
90010916
WARNINGWhen securing cargo, follow DOTguidelines 49 CFR section 393.100 to393.136 - Protection Against shifting andfalling cargo
90010916
WARNINGWhen securing cargo, follow DOTguidelines 49 CFR section 393.100 to393.136 - Protection Against shifting andfalling cargo
90010916
WARNINGWhen securing cargo, follow DOTguidelines 49 CFR section 393.100 to393.136 - Protection Against shifting andfalling cargo
90010916
CAUTION
90010913 90010913
90010912
9001
0903
9001
0903
Remove any externalchain tie downs orchocks from the floorand stowin a securelocationwhen notin use.
CAUTION
90010917
Remove any externalchain tie downs orchocks from the floorand stowin a securelocationwhen notin use.
CAUTION
90010917
ONLY POCKETS, PIPE SPOOLS, LASHINGRINGS, AND CHAIN TIE-DOWNS (IF SO
EQUIPPED) ARE ACCEPTABLE ANCHORPOINTS PER CMVSS 905 90010911
ONLY POCKETS, PIPE SPOOLS, LASHINGRINGS, AND CHAIN TIE-DOWNS (IF SO
EQUIPPED) ARE ACCEPTABLE ANCHORPOINTS PER CMVSS 905 90010911
ONLY POCKETS, PIPE SPOOLS, LASHINGRINGS, AND CHAIN TIE-DOWNS (IF SO
EQUIPPED) ARE ACCEPTABLE ANCHORPOINTS PER CMVSS 905 90010911
ONLY POCKETS, PIPE SPOOLS, LASHINGRINGS, AND CHAIN TIE-DOWNS (IF SO
EQUIPPED) ARE ACCEPTABLE ANCHORPOINTS PER CMVSS 905 90010911
POST / BRACELOCKING PIN MUST
BE ENGAGED:YELLOW TIP OF PINMUST BE VISIBLE.
DANGER
90010910
POST / BRACELOCKING PIN MUST
BE ENGAGED:YELLOW TIP OF PINMUST BE VISIBLE.
DANGER
90010910
POST / BRACELOCKING PIN MUST
BE ENGAGED:YELLOW TIP OF PINMUST BE VISIBLE.
DANGER
90010910
POST / BRACELOCKING PIN MUST
BE ENGAGED:YELLOW TIP OF PINMUST BE VISIBLE.
DANGER
90010910
90010908
90010908
90010908
90010908
90010908
90010907
90010907
CAUTIONPOST OR BRACE NOT TO BE
USED FOR ANCHORING LOADRESTRAINTS.
90010906
CAUTIONPOST OR BRACE NOT TO BE
USED FOR ANCHORING LOADRESTRAINTS.
90010906
CAUTIONPOST OR BRACE NOT TO BE
USED FOR ANCHORING LOADRESTRAINTS.
90010906
CAUTIONPOST OR BRACE NOT TO BE
USED FOR ANCHORING LOADRESTRAINTS.
90010906
KEEP HANDSCLEAR
90010905
CAUTIONKEEP HANDS
CLEAR90010905
CAUTIONKEEP HANDS
CLEAR90010905
CAUTIONKEEP HANDS
CLEAR90010905
90010904
90010904 90010904 90010904
3515 Industrial WayJasper, AL 355011-205-385-0451
www.fontainetrailer.com90010915
91”(inside loading height) 96 3/8”
(inside loading width)
91”(inside loading height) 96 3/8”
(inside loading width)
91”(inside loading height) 96 3/8”
(inside loading width)
91”(inside loading height) 96 3/8”
(inside loading width)
WARNING:DO NOT BUMP
ARMS WITH FORKS.
WARNING:DO NOT BUMP
ARMS WITH FORKS.
WARNING:DO NOT BUMP
ARMS WITH FORKS.
WARNING:DO NOT BUMP
ARMS WITH FORKS.
PATE
NT
PEN
DIN
G50
5074
40
WARNINGWhen securing cargo, follow DOTguidelines 49 CFR section 393.100 to393.136 - Protection Against shifting andfalling cargo
90010916
WARNINGWhen securing cargo, follow DOTguidelines 49 CFR section 393.100 to393.136 - Protection Against shifting andfalling cargo
90010916
WARNINGWhen securing cargo, follow DOTguidelines 49 CFR section 393.100 to393.136 - Protection Against shifting andfalling cargo
90010916
WARNINGWhen securing cargo, follow DOTguidelines 49 CFR section 393.100 to393.136 - Protection Against shifting andfalling cargo
90010916
CAUTION
90010913 90010913
90010912
9001
0903
9001
0903
Remove any externalchain tie downs orchocks from the floorand stowin a securelocationwhen notin use.
CAUTION
90010917
Remove any externalchain tie downs orchocks from the floorand stowin a securelocationwhen notin use.
CAUTION
90010917
ONLY POCKETS, PIPE SPOOLS, LASHINGRINGS, AND CHAIN TIE-DOWNS (IF SO
EQUIPPED) ARE ACCEPTABLE ANCHORPOINTS PER CMVSS 905 90010911
ONLY POCKETS, PIPE SPOOLS, LASHINGRINGS, AND CHAIN TIE-DOWNS (IF SO
EQUIPPED) ARE ACCEPTABLE ANCHORPOINTS PER CMVSS 905 90010911
ONLY POCKETS, PIPE SPOOLS, LASHINGRINGS, AND CHAIN TIE-DOWNS (IF SO
EQUIPPED) ARE ACCEPTABLE ANCHORPOINTS PER CMVSS 905 90010911
ONLY POCKETS, PIPE SPOOLS, LASHINGRINGS, AND CHAIN TIE-DOWNS (IF SO
EQUIPPED) ARE ACCEPTABLE ANCHORPOINTS PER CMVSS 905 90010911
POST / BRACELOCKING PIN MUST
BE ENGAGED:YELLOW TIP OF PINMUST BE VISIBLE.
DANGER
90010910
POST / BRACELOCKING PIN MUST
BE ENGAGED:YELLOW TIP OF PINMUST BE VISIBLE.
DANGER
90010910
POST / BRACELOCKING PIN MUST
BE ENGAGED:YELLOW TIP OF PINMUST BE VISIBLE.
DANGER
90010910
POST / BRACELOCKING PIN MUST
BE ENGAGED:YELLOW TIP OF PINMUST BE VISIBLE.
DANGER
90010910
90010908
90010908
90010908
90010908
90010908
90010907
90010907
CAUTIONPOST OR BRACE NOT TO BE
USED FOR ANCHORING LOADRESTRAINTS.
90010906
CAUTIONPOST OR BRACE NOT TO BE
USED FOR ANCHORING LOADRESTRAINTS.
90010906
CAUTIONPOST OR BRACE NOT TO BE
USED FOR ANCHORING LOADRESTRAINTS.
90010906
CAUTIONPOST OR BRACE NOT TO BE
USED FOR ANCHORING LOADRESTRAINTS.
90010906
KEEP HANDSCLEAR
90010905
CAUTIONKEEP HANDS
CLEAR90010905
CAUTIONKEEP HANDS
CLEAR90010905
CAUTIONKEEP HANDS
CLEAR90010905
90010904
90010904 90010904 90010904
3515 Industrial WayJasper, AL 355011-205-385-0451
www.fontainetrailer.com90010915
91”(inside loading height) 96 3/8”
(inside loading width)
91”(inside loading height) 96 3/8”
(inside loading width)
91”(inside loading height) 96 3/8”
(inside loading width)
91”(inside loading height) 96 3/8”
(inside loading width)
WARNING:DO NOT BUMP
ARMS WITH FORKS.
WARNING:DO NOT BUMP
ARMS WITH FORKS.
WARNING:DO NOT BUMP
ARMS WITH FORKS.
WARNING:DO NOT BUMP
ARMS WITH FORKS.
PATE
NT
PEN
DIN
G50
5074
40
“Front” Decals (3) – These decals designate which end of the unit is the front of the deck. This is important for multiple reasons. Most importantly, the concentrated load center is not directly in the center of the deck; it is slightly forward. Once the deck is loaded so that the weight is properly distributed on the truck and axles, it needs to be placed in that same orientation when it is positioned on another chassis. Therefore “Front” always needs to be “Front”. In addition, toolboxes are toward the front for easy availability, and the arm operation handles are located on the road side (driver’s side) when the deck is oriented properly.
Placement: Top of the Front Arm Assembly crosspost and on each front Support Arm Brace.
WARNINGWhen securing cargo, follow DOTguidelines 49 CFR section 393.100 to393.136 - Protection Against shifting andfalling cargo
90010916
WARNINGWhen securing cargo, follow DOTguidelines 49 CFR section 393.100 to393.136 - Protection Against shifting andfalling cargo
90010916
WARNINGWhen securing cargo, follow DOTguidelines 49 CFR section 393.100 to393.136 - Protection Against shifting andfalling cargo
90010916
WARNINGWhen securing cargo, follow DOTguidelines 49 CFR section 393.100 to393.136 - Protection Against shifting andfalling cargo
90010916
CAUTION
90010913 90010913
90010912
9001
0903
9001
0903
Remove any externalchain tie downs orchocks from the floorand stowin a securelocationwhen notin use.
CAUTION
90010917
Remove any externalchain tie downs orchocks from the floorand stowin a securelocationwhen notin use.
CAUTION
90010917
ONLY POCKETS, PIPE SPOOLS, LASHINGRINGS, AND CHAIN TIE-DOWNS (IF SO
EQUIPPED) ARE ACCEPTABLE ANCHORPOINTS PER CMVSS 905 90010911
ONLY POCKETS, PIPE SPOOLS, LASHINGRINGS, AND CHAIN TIE-DOWNS (IF SO
EQUIPPED) ARE ACCEPTABLE ANCHORPOINTS PER CMVSS 905 90010911
ONLY POCKETS, PIPE SPOOLS, LASHINGRINGS, AND CHAIN TIE-DOWNS (IF SO
EQUIPPED) ARE ACCEPTABLE ANCHORPOINTS PER CMVSS 905 90010911
ONLY POCKETS, PIPE SPOOLS, LASHINGRINGS, AND CHAIN TIE-DOWNS (IF SO
EQUIPPED) ARE ACCEPTABLE ANCHORPOINTS PER CMVSS 905 90010911
POST / BRACELOCKING PIN MUST
BE ENGAGED:YELLOW TIP OF PINMUST BE VISIBLE.
DANGER
90010910
POST / BRACELOCKING PIN MUST
BE ENGAGED:YELLOW TIP OF PINMUST BE VISIBLE.
DANGER
90010910
POST / BRACELOCKING PIN MUST
BE ENGAGED:YELLOW TIP OF PINMUST BE VISIBLE.
DANGER
90010910
POST / BRACELOCKING PIN MUST
BE ENGAGED:YELLOW TIP OF PINMUST BE VISIBLE.
DANGER
90010910
90010908
90010908
90010908
90010908
90010908
90010907
90010907
CAUTIONPOST OR BRACE NOT TO BE
USED FOR ANCHORING LOADRESTRAINTS.
90010906
CAUTIONPOST OR BRACE NOT TO BE
USED FOR ANCHORING LOADRESTRAINTS.
90010906
CAUTIONPOST OR BRACE NOT TO BE
USED FOR ANCHORING LOADRESTRAINTS.
90010906
CAUTIONPOST OR BRACE NOT TO BE
USED FOR ANCHORING LOADRESTRAINTS.
90010906
KEEP HANDSCLEAR
90010905
CAUTIONKEEP HANDS
CLEAR90010905
CAUTIONKEEP HANDS
CLEAR90010905
CAUTIONKEEP HANDS
CLEAR90010905
90010904
90010904 90010904 90010904
3515 Industrial WayJasper, AL 355011-205-385-0451
www.fontainetrailer.com90010915
91”(inside loading height) 96 3/8”
(inside loading width)
91”(inside loading height) 96 3/8”
(inside loading width)
91”(inside loading height) 96 3/8”
(inside loading width)
91”(inside loading height) 96 3/8”
(inside loading width)
WARNING:DO NOT BUMP
ARMS WITH FORKS.
WARNING:DO NOT BUMP
ARMS WITH FORKS.
WARNING:DO NOT BUMP
ARMS WITH FORKS.
WARNING:DO NOT BUMP
ARMS WITH FORKS.
PATE
NT
PEN
DIN
G50
5074
40
“For Empty Only” (2) – These decals denote that the deck should ONLY be lifted by a forklift when the deck is EMPTY and completely unloaded. Double check for loose items on the deck (winch bars, straps, etc…) before lifting with a forklift because items will slide off the deck as it moves.
Placement: Under the front forklift cutout on each side of the deck.
Required Decals
Section 1 - Important Information (continued)
WARNINGWhen securing cargo, follow DOTguidelines 49 CFR section 393.100 to393.136 - Protection Against shifting andfalling cargo
90010916
WARNINGWhen securing cargo, follow DOTguidelines 49 CFR section 393.100 to393.136 - Protection Against shifting andfalling cargo
90010916
WARNINGWhen securing cargo, follow DOTguidelines 49 CFR section 393.100 to393.136 - Protection Against shifting andfalling cargo
90010916
WARNINGWhen securing cargo, follow DOTguidelines 49 CFR section 393.100 to393.136 - Protection Against shifting andfalling cargo
90010916
CAUTION
90010913 90010913
90010912
9001
0903
9001
0903
Remove any externalchain tie downs orchocks from the floorand stowin a securelocationwhen notin use.
CAUTION
90010917
Remove any externalchain tie downs orchocks from the floorand stowin a securelocationwhen notin use.
CAUTION
90010917
ONLY POCKETS, PIPE SPOOLS, LASHINGRINGS, AND CHAIN TIE-DOWNS (IF SO
EQUIPPED) ARE ACCEPTABLE ANCHORPOINTS PER CMVSS 905 90010911
ONLY POCKETS, PIPE SPOOLS, LASHINGRINGS, AND CHAIN TIE-DOWNS (IF SO
EQUIPPED) ARE ACCEPTABLE ANCHORPOINTS PER CMVSS 905 90010911
ONLY POCKETS, PIPE SPOOLS, LASHINGRINGS, AND CHAIN TIE-DOWNS (IF SO
EQUIPPED) ARE ACCEPTABLE ANCHORPOINTS PER CMVSS 905 90010911
ONLY POCKETS, PIPE SPOOLS, LASHINGRINGS, AND CHAIN TIE-DOWNS (IF SO
EQUIPPED) ARE ACCEPTABLE ANCHORPOINTS PER CMVSS 905 90010911
POST / BRACELOCKING PIN MUST
BE ENGAGED:YELLOW TIP OF PINMUST BE VISIBLE.
DANGER
90010910
POST / BRACELOCKING PIN MUST
BE ENGAGED:YELLOW TIP OF PINMUST BE VISIBLE.
DANGER
90010910
POST / BRACELOCKING PIN MUST
BE ENGAGED:YELLOW TIP OF PINMUST BE VISIBLE.
DANGER
90010910
POST / BRACELOCKING PIN MUST
BE ENGAGED:YELLOW TIP OF PINMUST BE VISIBLE.
DANGER
90010910
90010908
90010908
90010908
90010908
90010908
90010907
90010907
CAUTIONPOST OR BRACE NOT TO BE
USED FOR ANCHORING LOADRESTRAINTS.
90010906
CAUTIONPOST OR BRACE NOT TO BE
USED FOR ANCHORING LOADRESTRAINTS.
90010906
CAUTIONPOST OR BRACE NOT TO BE
USED FOR ANCHORING LOADRESTRAINTS.
90010906
CAUTIONPOST OR BRACE NOT TO BE
USED FOR ANCHORING LOADRESTRAINTS.
90010906
KEEP HANDSCLEAR
90010905
CAUTIONKEEP HANDS
CLEAR90010905
CAUTIONKEEP HANDS
CLEAR90010905
CAUTIONKEEP HANDS
CLEAR90010905
90010904
90010904 90010904 90010904
3515 Industrial WayJasper, AL 355011-205-385-0451
www.fontainetrailer.com90010915
91”(inside loading height) 96 3/8”
(inside loading width)
91”(inside loading height) 96 3/8”
(inside loading width)
91”(inside loading height) 96 3/8”
(inside loading width)
91”(inside loading height) 96 3/8”
(inside loading width)
WARNING:DO NOT BUMP
ARMS WITH FORKS.
WARNING:DO NOT BUMP
ARMS WITH FORKS.
WARNING:DO NOT BUMP
ARMS WITH FORKS.
WARNING:DO NOT BUMP
ARMS WITH FORKS.
PATE
NT
PEN
DIN
G50
5074
40
“Fontaine Intermodal” (1) – This decal provides contact information for Fontaine Intermodal: address, phone number and website.
Location: Roadside front, next to the Unit Number Plate.
WARNINGWhen securing cargo, follow DOTguidelines 49 CFR section 393.100 to393.136 - Protection Against shifting andfalling cargo
90010916
WARNINGWhen securing cargo, follow DOTguidelines 49 CFR section 393.100 to393.136 - Protection Against shifting andfalling cargo
90010916
WARNINGWhen securing cargo, follow DOTguidelines 49 CFR section 393.100 to393.136 - Protection Against shifting andfalling cargo
90010916
WARNINGWhen securing cargo, follow DOTguidelines 49 CFR section 393.100 to393.136 - Protection Against shifting andfalling cargo
90010916
CAUTION
90010913 90010913
90010912
9001
0903
9001
0903
Remove any externalchain tie downs orchocks from the floorand stowin a securelocationwhen notin use.
CAUTION
90010917
Remove any externalchain tie downs orchocks from the floorand stowin a securelocationwhen notin use.
CAUTION
90010917
ONLY POCKETS, PIPE SPOOLS, LASHINGRINGS, AND CHAIN TIE-DOWNS (IF SO
EQUIPPED) ARE ACCEPTABLE ANCHORPOINTS PER CMVSS 905 90010911
ONLY POCKETS, PIPE SPOOLS, LASHINGRINGS, AND CHAIN TIE-DOWNS (IF SO
EQUIPPED) ARE ACCEPTABLE ANCHORPOINTS PER CMVSS 905 90010911
ONLY POCKETS, PIPE SPOOLS, LASHINGRINGS, AND CHAIN TIE-DOWNS (IF SO
EQUIPPED) ARE ACCEPTABLE ANCHORPOINTS PER CMVSS 905 90010911
ONLY POCKETS, PIPE SPOOLS, LASHINGRINGS, AND CHAIN TIE-DOWNS (IF SO
EQUIPPED) ARE ACCEPTABLE ANCHORPOINTS PER CMVSS 905 90010911
POST / BRACELOCKING PIN MUST
BE ENGAGED:YELLOW TIP OF PINMUST BE VISIBLE.
DANGER
90010910
POST / BRACELOCKING PIN MUST
BE ENGAGED:YELLOW TIP OF PINMUST BE VISIBLE.
DANGER
90010910
POST / BRACELOCKING PIN MUST
BE ENGAGED:YELLOW TIP OF PINMUST BE VISIBLE.
DANGER
90010910
POST / BRACELOCKING PIN MUST
BE ENGAGED:YELLOW TIP OF PINMUST BE VISIBLE.
DANGER
90010910
90010908
90010908
90010908
90010908
90010908
90010907
90010907
CAUTIONPOST OR BRACE NOT TO BE
USED FOR ANCHORING LOADRESTRAINTS.
90010906
CAUTIONPOST OR BRACE NOT TO BE
USED FOR ANCHORING LOADRESTRAINTS.
90010906
CAUTIONPOST OR BRACE NOT TO BE
USED FOR ANCHORING LOADRESTRAINTS.
90010906
CAUTIONPOST OR BRACE NOT TO BE
USED FOR ANCHORING LOADRESTRAINTS.
90010906
KEEP HANDSCLEAR
90010905
CAUTIONKEEP HANDS
CLEAR90010905
CAUTIONKEEP HANDS
CLEAR90010905
CAUTIONKEEP HANDS
CLEAR90010905
90010904
90010904 90010904 90010904
3515 Industrial WayJasper, AL 355011-205-385-0451
www.fontainetrailer.com90010915
91”(inside loading height) 96 3/8”
(inside loading width)
91”(inside loading height) 96 3/8”
(inside loading width)
91”(inside loading height) 96 3/8”
(inside loading width)
91”(inside loading height) 96 3/8”
(inside loading width)
WARNING:DO NOT BUMP
ARMS WITH FORKS.
WARNING:DO NOT BUMP
ARMS WITH FORKS.
WARNING:DO NOT BUMP
ARMS WITH FORKS.
WARNING:DO NOT BUMP
ARMS WITH FORKS.
PATE
NT
PEN
DIN
G50
5074
40
“Warning. When securing cargo follow DOT guidelines...” (4) – This decal denotes DOT guidelines for securing cargo. Because the Evolution is an intermodal product, AAR and other load securement regulations must be followed.
Location: Outside of the forklift cutouts on both sides of the deck.
6
www.fontaineintermodal.comFor service call 205-385-0451
To order parts call: 866-382-7278
Required Decals (Continued)
Section 1 - Important Information (continued)
WARNINGWhen securing cargo, follow DOTguidelines 49 CFR section 393.100 to393.136 - Protection Against shifting andfalling cargo
90010916
WARNINGWhen securing cargo, follow DOTguidelines 49 CFR section 393.100 to393.136 - Protection Against shifting andfalling cargo
90010916
WARNINGWhen securing cargo, follow DOTguidelines 49 CFR section 393.100 to393.136 - Protection Against shifting andfalling cargo
90010916
WARNINGWhen securing cargo, follow DOTguidelines 49 CFR section 393.100 to393.136 - Protection Against shifting andfalling cargo
90010916
CAUTION
90010913 90010913
90010912
9001
0903
9001
0903
Remove any externalchain tie downs orchocks from the floorand stowin a securelocationwhen notin use.
CAUTION
90010917
Remove any externalchain tie downs orchocks from the floorand stowin a securelocationwhen notin use.
CAUTION
90010917
ONLY POCKETS, PIPE SPOOLS, LASHINGRINGS, AND CHAIN TIE-DOWNS (IF SO
EQUIPPED) ARE ACCEPTABLE ANCHORPOINTS PER CMVSS 905 90010911
ONLY POCKETS, PIPE SPOOLS, LASHINGRINGS, AND CHAIN TIE-DOWNS (IF SO
EQUIPPED) ARE ACCEPTABLE ANCHORPOINTS PER CMVSS 905 90010911
ONLY POCKETS, PIPE SPOOLS, LASHINGRINGS, AND CHAIN TIE-DOWNS (IF SO
EQUIPPED) ARE ACCEPTABLE ANCHORPOINTS PER CMVSS 905 90010911
ONLY POCKETS, PIPE SPOOLS, LASHINGRINGS, AND CHAIN TIE-DOWNS (IF SO
EQUIPPED) ARE ACCEPTABLE ANCHORPOINTS PER CMVSS 905 90010911
POST / BRACELOCKING PIN MUST
BE ENGAGED:YELLOW TIP OF PINMUST BE VISIBLE.
DANGER
90010910
POST / BRACELOCKING PIN MUST
BE ENGAGED:YELLOW TIP OF PINMUST BE VISIBLE.
DANGER
90010910
POST / BRACELOCKING PIN MUST
BE ENGAGED:YELLOW TIP OF PINMUST BE VISIBLE.
DANGER
90010910
POST / BRACELOCKING PIN MUST
BE ENGAGED:YELLOW TIP OF PINMUST BE VISIBLE.
DANGER
90010910
90010908
90010908
90010908
90010908
90010908
90010907
90010907
CAUTIONPOST OR BRACE NOT TO BE
USED FOR ANCHORING LOADRESTRAINTS.
90010906
CAUTIONPOST OR BRACE NOT TO BE
USED FOR ANCHORING LOADRESTRAINTS.
90010906
CAUTIONPOST OR BRACE NOT TO BE
USED FOR ANCHORING LOADRESTRAINTS.
90010906
CAUTIONPOST OR BRACE NOT TO BE
USED FOR ANCHORING LOADRESTRAINTS.
90010906
KEEP HANDSCLEAR
90010905
CAUTIONKEEP HANDS
CLEAR90010905
CAUTIONKEEP HANDS
CLEAR90010905
CAUTIONKEEP HANDS
CLEAR90010905
90010904
90010904 90010904 90010904
3515 Industrial WayJasper, AL 355011-205-385-0451
www.fontainetrailer.com90010915
91”(inside loading height) 96 3/8”
(inside loading width)
91”(inside loading height) 96 3/8”
(inside loading width)
91”(inside loading height) 96 3/8”
(inside loading width)
91”(inside loading height) 96 3/8”
(inside loading width)
WARNING:DO NOT BUMP
ARMS WITH FORKS.
WARNING:DO NOT BUMP
ARMS WITH FORKS.
WARNING:DO NOT BUMP
ARMS WITH FORKS.
WARNING:DO NOT BUMP
ARMS WITH FORKS.
PATE
NT
PEN
DIN
G50
5074
40
“Caution. Keep hands clear” (4) – The purpose of this decal is to clarify that there are moving parts that create potential pinch points. There are multiple pinch points associated with the operation of the arms. Please make everyone aware of this before operating the arms.
Location: Main web, directly to the inside of each Lock Box Assembly on both sides of deck.
WARNINGWhen securing cargo, follow DOTguidelines 49 CFR section 393.100 to393.136 - Protection Against shifting andfalling cargo
90010916
WARNINGWhen securing cargo, follow DOTguidelines 49 CFR section 393.100 to393.136 - Protection Against shifting andfalling cargo
90010916
WARNINGWhen securing cargo, follow DOTguidelines 49 CFR section 393.100 to393.136 - Protection Against shifting andfalling cargo
90010916
WARNINGWhen securing cargo, follow DOTguidelines 49 CFR section 393.100 to393.136 - Protection Against shifting andfalling cargo
90010916
CAUTION
90010913 90010913
90010912
9001
0903
9001
0903
Remove any externalchain tie downs orchocks from the floorand stowin a securelocationwhen notin use.
CAUTION
90010917
Remove any externalchain tie downs orchocks from the floorand stowin a securelocationwhen notin use.
CAUTION
90010917
ONLY POCKETS, PIPE SPOOLS, LASHINGRINGS, AND CHAIN TIE-DOWNS (IF SO
EQUIPPED) ARE ACCEPTABLE ANCHORPOINTS PER CMVSS 905 90010911
ONLY POCKETS, PIPE SPOOLS, LASHINGRINGS, AND CHAIN TIE-DOWNS (IF SO
EQUIPPED) ARE ACCEPTABLE ANCHORPOINTS PER CMVSS 905 90010911
ONLY POCKETS, PIPE SPOOLS, LASHINGRINGS, AND CHAIN TIE-DOWNS (IF SO
EQUIPPED) ARE ACCEPTABLE ANCHORPOINTS PER CMVSS 905 90010911
ONLY POCKETS, PIPE SPOOLS, LASHINGRINGS, AND CHAIN TIE-DOWNS (IF SO
EQUIPPED) ARE ACCEPTABLE ANCHORPOINTS PER CMVSS 905 90010911
POST / BRACELOCKING PIN MUST
BE ENGAGED:YELLOW TIP OF PINMUST BE VISIBLE.
DANGER
90010910
POST / BRACELOCKING PIN MUST
BE ENGAGED:YELLOW TIP OF PINMUST BE VISIBLE.
DANGER
90010910
POST / BRACELOCKING PIN MUST
BE ENGAGED:YELLOW TIP OF PINMUST BE VISIBLE.
DANGER
90010910
POST / BRACELOCKING PIN MUST
BE ENGAGED:YELLOW TIP OF PINMUST BE VISIBLE.
DANGER
90010910
90010908
90010908
90010908
90010908
90010908
90010907
90010907
CAUTIONPOST OR BRACE NOT TO BE
USED FOR ANCHORING LOADRESTRAINTS.
90010906
CAUTIONPOST OR BRACE NOT TO BE
USED FOR ANCHORING LOADRESTRAINTS.
90010906
CAUTIONPOST OR BRACE NOT TO BE
USED FOR ANCHORING LOADRESTRAINTS.
90010906
CAUTIONPOST OR BRACE NOT TO BE
USED FOR ANCHORING LOADRESTRAINTS.
90010906
KEEP HANDSCLEAR
90010905
CAUTIONKEEP HANDS
CLEAR90010905
CAUTIONKEEP HANDS
CLEAR90010905
CAUTIONKEEP HANDS
CLEAR90010905
90010904
90010904 90010904 90010904
3515 Industrial WayJasper, AL 355011-205-385-0451
www.fontainetrailer.com90010915
91”(inside loading height) 96 3/8”
(inside loading width)
91”(inside loading height) 96 3/8”
(inside loading width)
91”(inside loading height) 96 3/8”
(inside loading width)
91”(inside loading height) 96 3/8”
(inside loading width)
WARNING:DO NOT BUMP
ARMS WITH FORKS.
WARNING:DO NOT BUMP
ARMS WITH FORKS.
WARNING:DO NOT BUMP
ARMS WITH FORKS.
WARNING:DO NOT BUMP
ARMS WITH FORKS.
PATE
NT
PEN
DIN
G50
5074
40
“Dimension” (4) – This decal shows the loading dimensions WHEN THE ARMS ARE IN THE LOCKED POSITION.
Location: Outside on all four Arm Assembly uprights.
WARNINGWhen securing cargo, follow DOTguidelines 49 CFR section 393.100 to393.136 - Protection Against shifting andfalling cargo
90010916
WARNINGWhen securing cargo, follow DOTguidelines 49 CFR section 393.100 to393.136 - Protection Against shifting andfalling cargo
90010916
WARNINGWhen securing cargo, follow DOTguidelines 49 CFR section 393.100 to393.136 - Protection Against shifting andfalling cargo
90010916
WARNINGWhen securing cargo, follow DOTguidelines 49 CFR section 393.100 to393.136 - Protection Against shifting andfalling cargo
90010916
CAUTION
90010913 90010913
90010912
9001
0903
9001
0903
Remove any externalchain tie downs orchocks from the floorand stowin a securelocationwhen notin use.
CAUTION
90010917
Remove any externalchain tie downs orchocks from the floorand stowin a securelocationwhen notin use.
CAUTION
90010917
ONLY POCKETS, PIPE SPOOLS, LASHINGRINGS, AND CHAIN TIE-DOWNS (IF SO
EQUIPPED) ARE ACCEPTABLE ANCHORPOINTS PER CMVSS 905 90010911
ONLY POCKETS, PIPE SPOOLS, LASHINGRINGS, AND CHAIN TIE-DOWNS (IF SO
EQUIPPED) ARE ACCEPTABLE ANCHORPOINTS PER CMVSS 905 90010911
ONLY POCKETS, PIPE SPOOLS, LASHINGRINGS, AND CHAIN TIE-DOWNS (IF SO
EQUIPPED) ARE ACCEPTABLE ANCHORPOINTS PER CMVSS 905 90010911
ONLY POCKETS, PIPE SPOOLS, LASHINGRINGS, AND CHAIN TIE-DOWNS (IF SO
EQUIPPED) ARE ACCEPTABLE ANCHORPOINTS PER CMVSS 905 90010911
POST / BRACELOCKING PIN MUST
BE ENGAGED:YELLOW TIP OF PINMUST BE VISIBLE.
DANGER
90010910
POST / BRACELOCKING PIN MUST
BE ENGAGED:YELLOW TIP OF PINMUST BE VISIBLE.
DANGER
90010910
POST / BRACELOCKING PIN MUST
BE ENGAGED:YELLOW TIP OF PINMUST BE VISIBLE.
DANGER
90010910
POST / BRACELOCKING PIN MUST
BE ENGAGED:YELLOW TIP OF PINMUST BE VISIBLE.
DANGER
90010910
90010908
90010908
90010908
90010908
90010908
90010907
90010907
CAUTIONPOST OR BRACE NOT TO BE
USED FOR ANCHORING LOADRESTRAINTS.
90010906
CAUTIONPOST OR BRACE NOT TO BE
USED FOR ANCHORING LOADRESTRAINTS.
90010906
CAUTIONPOST OR BRACE NOT TO BE
USED FOR ANCHORING LOADRESTRAINTS.
90010906
CAUTIONPOST OR BRACE NOT TO BE
USED FOR ANCHORING LOADRESTRAINTS.
90010906
KEEP HANDSCLEAR
90010905
CAUTIONKEEP HANDS
CLEAR90010905
CAUTIONKEEP HANDS
CLEAR90010905
CAUTIONKEEP HANDS
CLEAR90010905
90010904
90010904 90010904 90010904
3515 Industrial WayJasper, AL 355011-205-385-0451
www.fontainetrailer.com90010915
91”(inside loading height) 96 3/8”
(inside loading width)
91”(inside loading height) 96 3/8”
(inside loading width)
91”(inside loading height) 96 3/8”
(inside loading width)
91”(inside loading height) 96 3/8”
(inside loading width)
WARNING:DO NOT BUMP
ARMS WITH FORKS.
WARNING:DO NOT BUMP
ARMS WITH FORKS.
WARNING:DO NOT BUMP
ARMS WITH FORKS.
WARNING:DO NOT BUMP
ARMS WITH FORKS.
PATE
NT
PEN
DIN
G50
5074
40
“Place single coil here” (2) – This decal marks the location to place a single coil on the deck. This is important because the floor and the deck have added strength in this area and loads have been tested in this area.
Location: Main web next to the front fork lift cutout, both sides of deck.
WARNINGWhen securing cargo, follow DOTguidelines 49 CFR section 393.100 to393.136 - Protection Against shifting andfalling cargo
90010916
WARNINGWhen securing cargo, follow DOTguidelines 49 CFR section 393.100 to393.136 - Protection Against shifting andfalling cargo
90010916
WARNINGWhen securing cargo, follow DOTguidelines 49 CFR section 393.100 to393.136 - Protection Against shifting andfalling cargo
90010916
WARNINGWhen securing cargo, follow DOTguidelines 49 CFR section 393.100 to393.136 - Protection Against shifting andfalling cargo
90010916
CAUTION
90010913 90010913
90010912
9001
0903
9001
0903
Remove any externalchain tie downs orchocks from the floorand stowin a securelocationwhen notin use.
CAUTION
90010917
Remove any externalchain tie downs orchocks from the floorand stowin a securelocationwhen notin use.
CAUTION
90010917
ONLY POCKETS, PIPE SPOOLS, LASHINGRINGS, AND CHAIN TIE-DOWNS (IF SO
EQUIPPED) ARE ACCEPTABLE ANCHORPOINTS PER CMVSS 905 90010911
ONLY POCKETS, PIPE SPOOLS, LASHINGRINGS, AND CHAIN TIE-DOWNS (IF SO
EQUIPPED) ARE ACCEPTABLE ANCHORPOINTS PER CMVSS 905 90010911
ONLY POCKETS, PIPE SPOOLS, LASHINGRINGS, AND CHAIN TIE-DOWNS (IF SO
EQUIPPED) ARE ACCEPTABLE ANCHORPOINTS PER CMVSS 905 90010911
ONLY POCKETS, PIPE SPOOLS, LASHINGRINGS, AND CHAIN TIE-DOWNS (IF SO
EQUIPPED) ARE ACCEPTABLE ANCHORPOINTS PER CMVSS 905 90010911
POST / BRACELOCKING PIN MUST
BE ENGAGED:YELLOW TIP OF PINMUST BE VISIBLE.
DANGER
90010910
POST / BRACELOCKING PIN MUST
BE ENGAGED:YELLOW TIP OF PINMUST BE VISIBLE.
DANGER
90010910
POST / BRACELOCKING PIN MUST
BE ENGAGED:YELLOW TIP OF PINMUST BE VISIBLE.
DANGER
90010910
POST / BRACELOCKING PIN MUST
BE ENGAGED:YELLOW TIP OF PINMUST BE VISIBLE.
DANGER
90010910
90010908
90010908
90010908
90010908
90010908
90010907
90010907
CAUTIONPOST OR BRACE NOT TO BE
USED FOR ANCHORING LOADRESTRAINTS.
90010906
CAUTIONPOST OR BRACE NOT TO BE
USED FOR ANCHORING LOADRESTRAINTS.
90010906
CAUTIONPOST OR BRACE NOT TO BE
USED FOR ANCHORING LOADRESTRAINTS.
90010906
CAUTIONPOST OR BRACE NOT TO BE
USED FOR ANCHORING LOADRESTRAINTS.
90010906
KEEP HANDSCLEAR
90010905
CAUTIONKEEP HANDS
CLEAR90010905
CAUTIONKEEP HANDS
CLEAR90010905
CAUTIONKEEP HANDS
CLEAR90010905
90010904
90010904 90010904 90010904
3515 Industrial WayJasper, AL 355011-205-385-0451
www.fontainetrailer.com90010915
91”(inside loading height) 96 3/8”
(inside loading width)
91”(inside loading height) 96 3/8”
(inside loading width)
91”(inside loading height) 96 3/8”
(inside loading width)
91”(inside loading height) 96 3/8”
(inside loading width)
WARNING:DO NOT BUMP
ARMS WITH FORKS.
WARNING:DO NOT BUMP
ARMS WITH FORKS.
WARNING:DO NOT BUMP
ARMS WITH FORKS.
WARNING:DO NOT BUMP
ARMS WITH FORKS.
PATE
NT
PEN
DIN
G50
5074
40
“Only pockets, pipe spools, lashing rings and chain tie downs...” (4) – This decal denotes what can be used as an anchor point on this deck. The rubrail/wheel track is never to be used to secure a load or a tarp. Straps should travel through the siderail and never over the rubrail.
Location: Outside of forklift cutouts, both sides of deck.
WARNINGWhen securing cargo, follow DOTguidelines 49 CFR section 393.100 to393.136 - Protection Against shifting andfalling cargo
90010916
WARNINGWhen securing cargo, follow DOTguidelines 49 CFR section 393.100 to393.136 - Protection Against shifting andfalling cargo
90010916
WARNINGWhen securing cargo, follow DOTguidelines 49 CFR section 393.100 to393.136 - Protection Against shifting andfalling cargo
90010916
WARNINGWhen securing cargo, follow DOTguidelines 49 CFR section 393.100 to393.136 - Protection Against shifting andfalling cargo
90010916
CAUTION
90010913 90010913
90010912
9001
0903
9001
0903
Remove any externalchain tie downs orchocks from the floorand stowin a securelocationwhen notin use.
CAUTION
90010917
Remove any externalchain tie downs orchocks from the floorand stowin a securelocationwhen notin use.
CAUTION
90010917
ONLY POCKETS, PIPE SPOOLS, LASHINGRINGS, AND CHAIN TIE-DOWNS (IF SO
EQUIPPED) ARE ACCEPTABLE ANCHORPOINTS PER CMVSS 905 90010911
ONLY POCKETS, PIPE SPOOLS, LASHINGRINGS, AND CHAIN TIE-DOWNS (IF SO
EQUIPPED) ARE ACCEPTABLE ANCHORPOINTS PER CMVSS 905 90010911
ONLY POCKETS, PIPE SPOOLS, LASHINGRINGS, AND CHAIN TIE-DOWNS (IF SO
EQUIPPED) ARE ACCEPTABLE ANCHORPOINTS PER CMVSS 905 90010911
ONLY POCKETS, PIPE SPOOLS, LASHINGRINGS, AND CHAIN TIE-DOWNS (IF SO
EQUIPPED) ARE ACCEPTABLE ANCHORPOINTS PER CMVSS 905 90010911
POST / BRACELOCKING PIN MUST
BE ENGAGED:YELLOW TIP OF PINMUST BE VISIBLE.
DANGER
90010910
POST / BRACELOCKING PIN MUST
BE ENGAGED:YELLOW TIP OF PINMUST BE VISIBLE.
DANGER
90010910
POST / BRACELOCKING PIN MUST
BE ENGAGED:YELLOW TIP OF PINMUST BE VISIBLE.
DANGER
90010910
POST / BRACELOCKING PIN MUST
BE ENGAGED:YELLOW TIP OF PINMUST BE VISIBLE.
DANGER
90010910
90010908
90010908
90010908
90010908
90010908
90010907
90010907
CAUTIONPOST OR BRACE NOT TO BE
USED FOR ANCHORING LOADRESTRAINTS.
90010906
CAUTIONPOST OR BRACE NOT TO BE
USED FOR ANCHORING LOADRESTRAINTS.
90010906
CAUTIONPOST OR BRACE NOT TO BE
USED FOR ANCHORING LOADRESTRAINTS.
90010906
CAUTIONPOST OR BRACE NOT TO BE
USED FOR ANCHORING LOADRESTRAINTS.
90010906
KEEP HANDSCLEAR
90010905
CAUTIONKEEP HANDS
CLEAR90010905
CAUTIONKEEP HANDS
CLEAR90010905
CAUTIONKEEP HANDS
CLEAR90010905
90010904
90010904 90010904 90010904
3515 Industrial WayJasper, AL 355011-205-385-0451
www.fontainetrailer.com90010915
91”(inside loading height) 96 3/8”
(inside loading width)
91”(inside loading height) 96 3/8”
(inside loading width)
91”(inside loading height) 96 3/8”
(inside loading width)
91”(inside loading height) 96 3/8”
(inside loading width)
WARNING:DO NOT BUMP
ARMS WITH FORKS.
WARNING:DO NOT BUMP
ARMS WITH FORKS.
WARNING:DO NOT BUMP
ARMS WITH FORKS.
WARNING:DO NOT BUMP
ARMS WITH FORKS.
PATE
NT
PEN
DIN
G50
5074
40
“Caution. Post or Brace not to be used for anchoring load restraints" (4) – This decal denotes that the Arm Assemblies and Arm Support Braces on the deck are not to be used for load securement. Never attach straps, chains or any load securement device to the Arm Assemblies and Arm Support Braces.
Location: Main web next to the front fork lift cutout on both sides of the deck.
7
www.fontaineintermodal.comFor service call 205-385-0451
To order parts call: 866-382-7278
Required Decals (Continued)
Section 1 - Important Information (continued)
WARNINGWhen securing cargo, follow DOTguidelines 49 CFR section 393.100 to393.136 - Protection Against shifting andfalling cargo
90010916
WARNINGWhen securing cargo, follow DOTguidelines 49 CFR section 393.100 to393.136 - Protection Against shifting andfalling cargo
90010916
WARNINGWhen securing cargo, follow DOTguidelines 49 CFR section 393.100 to393.136 - Protection Against shifting andfalling cargo
90010916
WARNINGWhen securing cargo, follow DOTguidelines 49 CFR section 393.100 to393.136 - Protection Against shifting andfalling cargo
90010916
CAUTION
90010913 90010913
90010912
9001
0903
9001
0903
Remove any externalchain tie downs orchocks from the floorand stowin a securelocationwhen notin use.
CAUTION
90010917
Remove any externalchain tie downs orchocks from the floorand stowin a securelocationwhen notin use.
CAUTION
90010917
ONLY POCKETS, PIPE SPOOLS, LASHINGRINGS, AND CHAIN TIE-DOWNS (IF SO
EQUIPPED) ARE ACCEPTABLE ANCHORPOINTS PER CMVSS 905 90010911
ONLY POCKETS, PIPE SPOOLS, LASHINGRINGS, AND CHAIN TIE-DOWNS (IF SO
EQUIPPED) ARE ACCEPTABLE ANCHORPOINTS PER CMVSS 905 90010911
ONLY POCKETS, PIPE SPOOLS, LASHINGRINGS, AND CHAIN TIE-DOWNS (IF SO
EQUIPPED) ARE ACCEPTABLE ANCHORPOINTS PER CMVSS 905 90010911
ONLY POCKETS, PIPE SPOOLS, LASHINGRINGS, AND CHAIN TIE-DOWNS (IF SO
EQUIPPED) ARE ACCEPTABLE ANCHORPOINTS PER CMVSS 905 90010911
POST / BRACELOCKING PIN MUST
BE ENGAGED:YELLOW TIP OF PINMUST BE VISIBLE.
DANGER
90010910
POST / BRACELOCKING PIN MUST
BE ENGAGED:YELLOW TIP OF PINMUST BE VISIBLE.
DANGER
90010910
POST / BRACELOCKING PIN MUST
BE ENGAGED:YELLOW TIP OF PINMUST BE VISIBLE.
DANGER
90010910
POST / BRACELOCKING PIN MUST
BE ENGAGED:YELLOW TIP OF PINMUST BE VISIBLE.
DANGER
90010910
90010908
90010908
90010908
90010908
90010908
90010907
90010907
CAUTIONPOST OR BRACE NOT TO BE
USED FOR ANCHORING LOADRESTRAINTS.
90010906
CAUTIONPOST OR BRACE NOT TO BE
USED FOR ANCHORING LOADRESTRAINTS.
90010906
CAUTIONPOST OR BRACE NOT TO BE
USED FOR ANCHORING LOADRESTRAINTS.
90010906
CAUTIONPOST OR BRACE NOT TO BE
USED FOR ANCHORING LOADRESTRAINTS.
90010906
KEEP HANDSCLEAR
90010905
CAUTIONKEEP HANDS
CLEAR90010905
CAUTIONKEEP HANDS
CLEAR90010905
CAUTIONKEEP HANDS
CLEAR90010905
90010904
90010904 90010904 90010904
3515 Industrial WayJasper, AL 355011-205-385-0451
www.fontainetrailer.com90010915
91”(inside loading height) 96 3/8”
(inside loading width)
91”(inside loading height) 96 3/8”
(inside loading width)
91”(inside loading height) 96 3/8”
(inside loading width)
91”(inside loading height) 96 3/8”
(inside loading width)
WARNING:DO NOT BUMP
ARMS WITH FORKS.
WARNING:DO NOT BUMP
ARMS WITH FORKS.
WARNING:DO NOT BUMP
ARMS WITH FORKS.
WARNING:DO NOT BUMP
ARMS WITH FORKS.
PATE
NT
PEN
DIN
G50
5074
40
“WTP” (8) – WTP ( Wide Top Pick) denotes the spacing for the crane to lift the deck at intermodal yards.
Location: Outside top of each Arm Assembly upright and on each side of the Arm Assembly crosstubes.
WARNINGWhen securing cargo, follow DOTguidelines 49 CFR section 393.100 to393.136 - Protection Against shifting andfalling cargo
90010916
WARNINGWhen securing cargo, follow DOTguidelines 49 CFR section 393.100 to393.136 - Protection Against shifting andfalling cargo
90010916
WARNINGWhen securing cargo, follow DOTguidelines 49 CFR section 393.100 to393.136 - Protection Against shifting andfalling cargo
90010916
WARNINGWhen securing cargo, follow DOTguidelines 49 CFR section 393.100 to393.136 - Protection Against shifting andfalling cargo
90010916
CAUTION
90010913 90010913
90010912
9001
0903
9001
0903
Remove any externalchain tie downs orchocks from the floorand stowin a securelocationwhen notin use.
CAUTION
90010917
Remove any externalchain tie downs orchocks from the floorand stowin a securelocationwhen notin use.
CAUTION
90010917
ONLY POCKETS, PIPE SPOOLS, LASHINGRINGS, AND CHAIN TIE-DOWNS (IF SO
EQUIPPED) ARE ACCEPTABLE ANCHORPOINTS PER CMVSS 905 90010911
ONLY POCKETS, PIPE SPOOLS, LASHINGRINGS, AND CHAIN TIE-DOWNS (IF SO
EQUIPPED) ARE ACCEPTABLE ANCHORPOINTS PER CMVSS 905 90010911
ONLY POCKETS, PIPE SPOOLS, LASHINGRINGS, AND CHAIN TIE-DOWNS (IF SO
EQUIPPED) ARE ACCEPTABLE ANCHORPOINTS PER CMVSS 905 90010911
ONLY POCKETS, PIPE SPOOLS, LASHINGRINGS, AND CHAIN TIE-DOWNS (IF SO
EQUIPPED) ARE ACCEPTABLE ANCHORPOINTS PER CMVSS 905 90010911
POST / BRACELOCKING PIN MUST
BE ENGAGED:YELLOW TIP OF PINMUST BE VISIBLE.
DANGER
90010910
POST / BRACELOCKING PIN MUST
BE ENGAGED:YELLOW TIP OF PINMUST BE VISIBLE.
DANGER
90010910
POST / BRACELOCKING PIN MUST
BE ENGAGED:YELLOW TIP OF PINMUST BE VISIBLE.
DANGER
90010910
POST / BRACELOCKING PIN MUST
BE ENGAGED:YELLOW TIP OF PINMUST BE VISIBLE.
DANGER
90010910
90010908
90010908
90010908
90010908
90010908
90010907
90010907
CAUTIONPOST OR BRACE NOT TO BE
USED FOR ANCHORING LOADRESTRAINTS.
90010906
CAUTIONPOST OR BRACE NOT TO BE
USED FOR ANCHORING LOADRESTRAINTS.
90010906
CAUTIONPOST OR BRACE NOT TO BE
USED FOR ANCHORING LOADRESTRAINTS.
90010906
CAUTIONPOST OR BRACE NOT TO BE
USED FOR ANCHORING LOADRESTRAINTS.
90010906
KEEP HANDSCLEAR
90010905
CAUTIONKEEP HANDS
CLEAR90010905
CAUTIONKEEP HANDS
CLEAR90010905
CAUTIONKEEP HANDS
CLEAR90010905
90010904
90010904 90010904 90010904
3515 Industrial WayJasper, AL 355011-205-385-0451
www.fontainetrailer.com90010915
91”(inside loading height) 96 3/8”
(inside loading width)
91”(inside loading height) 96 3/8”
(inside loading width)
91”(inside loading height) 96 3/8”
(inside loading width)
91”(inside loading height) 96 3/8”
(inside loading width)
WARNING:DO NOT BUMP
ARMS WITH FORKS.
WARNING:DO NOT BUMP
ARMS WITH FORKS.
WARNING:DO NOT BUMP
ARMS WITH FORKS.
WARNING:DO NOT BUMP
ARMS WITH FORKS.
PATE
NT
PEN
DIN
G50
5074
40
“Danger. Post/brace Locking-Pin must be engaged… (4) – This decal tells the operator that the arm is not in the locked position unless the yellow tip of the Lock Box Pin is pulled out and visible.
Location: Front surface of each Lock Box.
WARNINGWhen securing cargo, follow DOTguidelines 49 CFR section 393.100 to393.136 - Protection Against shifting andfalling cargo
90010916
WARNINGWhen securing cargo, follow DOTguidelines 49 CFR section 393.100 to393.136 - Protection Against shifting andfalling cargo
90010916
WARNINGWhen securing cargo, follow DOTguidelines 49 CFR section 393.100 to393.136 - Protection Against shifting andfalling cargo
90010916
WARNINGWhen securing cargo, follow DOTguidelines 49 CFR section 393.100 to393.136 - Protection Against shifting andfalling cargo
90010916
CAUTION
90010913 90010913
90010912
9001
0903
9001
0903
Remove any externalchain tie downs orchocks from the floorand stowin a securelocationwhen notin use.
CAUTION
90010917
Remove any externalchain tie downs orchocks from the floorand stowin a securelocationwhen notin use.
CAUTION
90010917
ONLY POCKETS, PIPE SPOOLS, LASHINGRINGS, AND CHAIN TIE-DOWNS (IF SO
EQUIPPED) ARE ACCEPTABLE ANCHORPOINTS PER CMVSS 905 90010911
ONLY POCKETS, PIPE SPOOLS, LASHINGRINGS, AND CHAIN TIE-DOWNS (IF SO
EQUIPPED) ARE ACCEPTABLE ANCHORPOINTS PER CMVSS 905 90010911
ONLY POCKETS, PIPE SPOOLS, LASHINGRINGS, AND CHAIN TIE-DOWNS (IF SO
EQUIPPED) ARE ACCEPTABLE ANCHORPOINTS PER CMVSS 905 90010911
ONLY POCKETS, PIPE SPOOLS, LASHINGRINGS, AND CHAIN TIE-DOWNS (IF SO
EQUIPPED) ARE ACCEPTABLE ANCHORPOINTS PER CMVSS 905 90010911
POST / BRACELOCKING PIN MUST
BE ENGAGED:YELLOW TIP OF PINMUST BE VISIBLE.
DANGER
90010910
POST / BRACELOCKING PIN MUST
BE ENGAGED:YELLOW TIP OF PINMUST BE VISIBLE.
DANGER
90010910
POST / BRACELOCKING PIN MUST
BE ENGAGED:YELLOW TIP OF PINMUST BE VISIBLE.
DANGER
90010910
POST / BRACELOCKING PIN MUST
BE ENGAGED:YELLOW TIP OF PINMUST BE VISIBLE.
DANGER
90010910
90010908
90010908
90010908
90010908
90010908
90010907
90010907
CAUTIONPOST OR BRACE NOT TO BE
USED FOR ANCHORING LOADRESTRAINTS.
90010906
CAUTIONPOST OR BRACE NOT TO BE
USED FOR ANCHORING LOADRESTRAINTS.
90010906
CAUTIONPOST OR BRACE NOT TO BE
USED FOR ANCHORING LOADRESTRAINTS.
90010906
CAUTIONPOST OR BRACE NOT TO BE
USED FOR ANCHORING LOADRESTRAINTS.
90010906
KEEP HANDSCLEAR
90010905
CAUTIONKEEP HANDS
CLEAR90010905
CAUTIONKEEP HANDS
CLEAR90010905
CAUTIONKEEP HANDS
CLEAR90010905
90010904
90010904 90010904 90010904
3515 Industrial WayJasper, AL 355011-205-385-0451
www.fontainetrailer.com90010915
91”(inside loading height) 96 3/8”
(inside loading width)
91”(inside loading height) 96 3/8”
(inside loading width)
91”(inside loading height) 96 3/8”
(inside loading width)
91”(inside loading height) 96 3/8”
(inside loading width)
WARNING:DO NOT BUMP
ARMS WITH FORKS.
WARNING:DO NOT BUMP
ARMS WITH FORKS.
WARNING:DO NOT BUMP
ARMS WITH FORKS.
WARNING:DO NOT BUMP
ARMS WITH FORKS.
PATE
NT
PEN
DIN
G50
5074
40
“Caution. Remove any external chain tie downs…" (2) – This decal is a reminder to remove any load securement devices from the deck that are not being used before transit.
Location: Main web next to the front fork lift cutout, both sides of deck.
WARNINGWhen securing cargo, follow DOTguidelines 49 CFR section 393.100 to393.136 - Protection Against shifting andfalling cargo
90010916
WARNINGWhen securing cargo, follow DOTguidelines 49 CFR section 393.100 to393.136 - Protection Against shifting andfalling cargo
90010916
WARNINGWhen securing cargo, follow DOTguidelines 49 CFR section 393.100 to393.136 - Protection Against shifting andfalling cargo
90010916
WARNINGWhen securing cargo, follow DOTguidelines 49 CFR section 393.100 to393.136 - Protection Against shifting andfalling cargo
90010916
CAUTION
90010913 90010913
90010912
9001
0903
9001
0903
Remove any externalchain tie downs orchocks from the floorand stowin a securelocationwhen notin use.
CAUTION
90010917
Remove any externalchain tie downs orchocks from the floorand stowin a securelocationwhen notin use.
CAUTION
90010917
ONLY POCKETS, PIPE SPOOLS, LASHINGRINGS, AND CHAIN TIE-DOWNS (IF SO
EQUIPPED) ARE ACCEPTABLE ANCHORPOINTS PER CMVSS 905 90010911
ONLY POCKETS, PIPE SPOOLS, LASHINGRINGS, AND CHAIN TIE-DOWNS (IF SO
EQUIPPED) ARE ACCEPTABLE ANCHORPOINTS PER CMVSS 905 90010911
ONLY POCKETS, PIPE SPOOLS, LASHINGRINGS, AND CHAIN TIE-DOWNS (IF SO
EQUIPPED) ARE ACCEPTABLE ANCHORPOINTS PER CMVSS 905 90010911
ONLY POCKETS, PIPE SPOOLS, LASHINGRINGS, AND CHAIN TIE-DOWNS (IF SO
EQUIPPED) ARE ACCEPTABLE ANCHORPOINTS PER CMVSS 905 90010911
POST / BRACELOCKING PIN MUST
BE ENGAGED:YELLOW TIP OF PINMUST BE VISIBLE.
DANGER
90010910
POST / BRACELOCKING PIN MUST
BE ENGAGED:YELLOW TIP OF PINMUST BE VISIBLE.
DANGER
90010910
POST / BRACELOCKING PIN MUST
BE ENGAGED:YELLOW TIP OF PINMUST BE VISIBLE.
DANGER
90010910
POST / BRACELOCKING PIN MUST
BE ENGAGED:YELLOW TIP OF PINMUST BE VISIBLE.
DANGER
90010910
90010908
90010908
90010908
90010908
90010908
90010907
90010907
CAUTIONPOST OR BRACE NOT TO BE
USED FOR ANCHORING LOADRESTRAINTS.
90010906
CAUTIONPOST OR BRACE NOT TO BE
USED FOR ANCHORING LOADRESTRAINTS.
90010906
CAUTIONPOST OR BRACE NOT TO BE
USED FOR ANCHORING LOADRESTRAINTS.
90010906
CAUTIONPOST OR BRACE NOT TO BE
USED FOR ANCHORING LOADRESTRAINTS.
90010906
KEEP HANDSCLEAR
90010905
CAUTIONKEEP HANDS
CLEAR90010905
CAUTIONKEEP HANDS
CLEAR90010905
CAUTIONKEEP HANDS
CLEAR90010905
90010904
90010904 90010904 90010904
3515 Industrial WayJasper, AL 355011-205-385-0451
www.fontainetrailer.com90010915
91”(inside loading height) 96 3/8”
(inside loading width)
91”(inside loading height) 96 3/8”
(inside loading width)
91”(inside loading height) 96 3/8”
(inside loading width)
91”(inside loading height) 96 3/8”
(inside loading width)
WARNING:DO NOT BUMP
ARMS WITH FORKS.
WARNING:DO NOT BUMP
ARMS WITH FORKS.
WARNING:DO NOT BUMP
ARMS WITH FORKS.
WARNING:DO NOT BUMP
ARMS WITH FORKS.
PATE
NT
PEN
DIN
G50
5074
40
“9'6" High” (4) – 9'6" is the overall height of the unit from its lowest point to its highest point with the arms in the upright position.
Location: Outside of Arm Assembly uprights toward the top.
"Unit Numbers” (2) –These decals denote the owner and their unit number.
Location: Outside of Arm Assembly uprights.
"Do not bump” (4) – Located on each arm.
"Load in 20 ft Capable Wells Only” (2) –Located on both sides.
8
www.fontaineintermodal.comFor service call 205-385-0451
To order parts call: 866-382-7278
NOTEALL WORKING LOAD LIMITS (WLL) PERTAIN TO STANDARD TEST RESULTS PERFORMED BY FONTAINE TRAILER COMPANY OR A QUALIFIED TESTING FACILITY.
Anchor Points describe points that are considered part of the trailer and NOT the securing device (chains, cables, straps). Securing devices must be of sufficient design to not cut into or deform the anchor point and must be rated equal to or greater than the Working Load Limit (WLL) of the anchor point to obtain maximum anchor point rating.
CAUTIONALL ANCHOR POINTS MUST HAVE A VISUAL INSPECTION PRIOR TO USE. IF AN ANCHOR POINT IS VISIBLY DAMAGED (DEFORMED, BENT, TORN, RIPPED, CRACKED (OR ANY OTHER STRUCTURAL DEFECT), DO NOT USE THE ANCHOR.
WARNINGDO NOT EXCEED THE WORKING LOAD LIMITS OF ANY ANCHOR POINT.
ANCHOR POINTS:
Chain tie downs – Maximum Load Limit- 5,400 lbs per tie down ( 22 per siderail, 44 per unit).
Turtle – Maximum Load Limit- 5,400 lbs per turtle.
WARNINGTHE LOAD LIMIT IS 5,400 LBS AT EVERY LOAD SECUREMENT LOCATION ON THE EVOLUTION WHERE THERE IS A CHAIN TIE DOWN; OR WHERE THERE IS A TURTLE PROPERLY PLACED, INSERTED INTO THE DECK GROOVES.
Load Securement
Section 1 - Important Information (continued)
9
www.fontaineintermodal.comFor service call 205-385-0451
To order parts call: 866-382-7278
FONTAINE PROVIDED WINCH AND WINCH STRAPS:
Ancra Sliding Double L style winch with AAR approved “Ancra Xtreme” strap (Maximum Load Limit is 5,400 lbs per strap).
Load Securement
The table below corresponds with the Association of American Railroads (AAR) Top Loading Rules, Section 1, Table 20.02 Current as of January 29, 2014
WARNINGWARNING: NOT ALL STRAPS ARE AAR (ASSOCIATION OF AMERICAN RAILROAD) APPROVED. SEE THE CHART BELOW FOR A LISTING. THE CURRENT LIST CAN BE FOUND ON THE AMERICAN ASSOCIATION OF RAILROADS WEBSITE: WWW.AAR.COM
FOR ALL REPLACEMENT WINCHES AND STRAPS, VERIFY THE WORKING LOAD LIMIT.
Section 1 - Important Information (continued)
10
www.fontaineintermodal.comFor service call 205-385-0451
To order parts call: 866-382-7278
Support Arm uprights, Arm Support Braces and stacking blocks are never to be used as an anchor point!
WARNINGLOAD SECUREMENT IS THE DRIVER’S RESPONSIBILITY. FOR ALL INTERMODAL LOADS, DOT REGULATIONS AND RAILROAD REGULATIONS MUST BE MET. IT IS UP TO EACH CUSTOMER TO RECEIVE PRIOR APPROVAL FOR NEW TYPES OF LOADS FROM THE RAILROADS.
WARNINGWHEN LOADING AN EVOLUTION, KEEP IN MIND THAT THE LOAD WILL TRAVEL ACROSS COUNTRY WITH NO OPPORTUNITY TO ADJUST LOAD SECUREMENT. THUS, THE LOAD MUST BE SECURED CORRECTLY THE FIRST TIME. THERE IS NO SECOND CHANCE!
SOME EXAMPLES OF IMPROPER SECUREMENT:
Rubrail/wheel track is not considered an anchor point. Do not hook straps or chains!
The bumper area and forklift lift areas are not to be used as anchor points.
The flange of the main beam is not an anchor point.
Load Securement
Section 1 - Important Information (continued)
11
www.fontaineintermodal.comFor service call 205-385-0451
To order parts call: 866-382-7278
The Fontaine Evolution features manually operated Support Arms for ease of use, convenience and unmatched reliability. While the Evolution Support Arms are designed to be very simple and user friendly, there are a few simple procedures and information you need to know prior to operation:
There are three basic Evolution arm positions:
1. Collapsed position - Single unit or stacked for repositioning. When repositioning a single Evolution deck in the empty position, the arms can be rotated down onto the deck surface, or “collapsed.”
2. Loading position - Arms rotated outward for maximum access to deck surface for easier loading.
3. Loaded transport position – Locked into position for transporting loaded units either as a single unit for the road or double-stacked for intermodal rail.
Introduction
Section 2 - Arm Operation
When repositioning multiple Evolution decks in the empty position, the arms can be rotated down onto the deck surface, or “collapsed” and stacked three-high or four-high for rail transport.
12
www.fontaineintermodal.comFor service call 205-385-0451
To order parts call: 866-382-7278
Section 2 - Arm Operation (continued)
To operate the Evolution arms, the Crank Shaft must be pulled out from inside the Support Arm. Using a Fontaine winch bar crank handle, insert the end into the center hole of the yellow painted Crank-Shaft, hook the lip of the handle behind the crank shaft and pull outward.
Getting Started
Once the crank shaft is exposed, insert the opposite end of the winch bar crank handle through the holes on either side and secure with the snap pin.
Crank Shaft
Winch bar Crank Handle
Use this end of the Crank Handle to pull
out yellow Crank Shaft.
Use this end of the Crank Handle to connect to the yellow shaft in order to turn the crank.
Winch bar Crank Handle
13
www.fontaineintermodal.comFor service call 205-385-0451
To order parts call: 866-382-7278
Section 2 - Arm Operation (continued)
During operation if the arms provide excessive resistance or no resistance, cease operating and call Fontaine for assistance: 205-385-0451.
WARNING FORCING THE ARM UP OR DOWN USING A CHEATER PIPE OR HANGING ON THE CRANK HANDLE COULD RESULT IN PERSONAL INJURY TO THE OPERATOR OR SOMEONE IN THE AREA AND MORE DAMAGE TO THE EQUIPMENT.
Fontaine offers a power unit to raise and lower the support arms. This device replaces the manual crank providing greater convenience and ease of operation. Call 866-382-7278 for more information.
Getting Started (continued)
Support Arm Power Unit
14
www.fontaineintermodal.comFor service call 205-385-0451
To order parts call: 866-382-7278
Section 2 - Arm Operation (continued)
The Evolution has a double-pin locking system. Each Support Arm has a “Locating-Pin” and a “Locking-Pin” on both sides of the deck. For identification purposes, the Locating-Pin is always the pin closest to the end of the deck and the Locking-Pin is always the pin closest to the center of the deck.
NOTETHE LOCATING-PIN IS ALWAYS THE PIN CLOSEST TO THE END OF THE DECK AND THE LOCKING-PIN IS ALWAYS THE PIN CLOSEST TO THE CENTER OF THE DECK.
To move the Support Arms from flat to upright:
1. Make sure that the Locating-Pin is engaged and that the Locking-Pin is NOT engaged.
2. Crank the handle in the desired direction of travel until the hook on the arm fully seats on the Locating-Pin and will turn no further.
3. Engage all pins and Lockout Tabs.
CAUTIONWHEN THE HOOK ON THE ARM FULLY SEATS ON THE LOCATING-PIN DO NOT USE EXCESSIVE FORCE TO TURN FURTHER AND NEVER USE A CHEATER BAR TO EXTEND THE HANDLE.
WARNINGFOR LOADED TRANSPORT ALL 4 LOCKING-PINS AND ALL 4 LOCATING-PINS SHOULD BE ENGAGED WITH THE POSITIVE LOCKOUT TABS FLIPPED DOWN.
Moving Arms from Flat to Upright
Locking-Pin engaged with positive Lockout Tab flipped down.
Locating-Pin and Locking-Pin in the engaged position.
Lockout Tab
Locking-Pin
Locking-PinLocating-Pin
Engage the Locking-Pins on both sides of the deck so that the yellow tips are visible and the positive Lockout Tabs are flipped down to lock the pins in position.
15
www.fontaineintermodal.comFor service call 205-385-0451
To order parts call: 866-382-7278
Section 2 - Arm Operation (continued)
For loading freight the arms can be set in the outward or "Loading" position.
1. Make sure the Locking-Pins are disengaged.
2. Turn the crank in the desired direction of travel and roll the arms downward until both Locating-Pins are free.
3. Disengage the Locating-Pins and flip down the positive Lockout Tab.
4. Turn crank backwards until the arm bottoms out on the 40 ft stacking block.
Locking-Pins are not engaged during loading.
Reverse this procedure to put arms back in the upright or loaded position.
NOTETHE LOCATING-PIN IS ALWAYS THE PIN CLOSEST TO THE END OF THE DECK AND THE LOCKING-PIN IS ALWAYS THE PIN CLOSEST TO THE CENTER OF THE DECK.
Positioning Arms for LoadingTo move arm
To move arm
Rotate handle
Rotate handle
Locating-Pin and Locking-Pin in the engaged position.
Locking-PinLocating-Pin
16
www.fontaineintermodal.comFor service call 205-385-0451
To order parts call: 866-382-7278
Section 2 - Arm Operation (continued)
1. Disengage all Locking-Pins.
2. Turn Crank Handle in desired direction of arm travel until the top stacking blocks rest on the deck.
3. Remove Crank Handle from crank shaft and push crank shaft in to arm.
4. Ensure that all 8 positive Lockout Tabs are in the down position.
Support Arms are designed to remain in the collapsed position without additional load securement ( straps, etc.) Consult AAR loading standards for additional requirements.
Positioning Arms for Empty Transit
Locating-Pin and Locking-Pin in the engaged position.
Locking-PinLocating-Pin
NOTETHE LOCATING-PIN IS ALWAYS THE PIN CLOSEST TO THE END OF THE DECK AND THE LOCKING-PIN IS ALWAYS THE PIN CLOSEST TO THE CENTER OF THE DECK.
Locking-Pin engaged with positive Lockout Tab flipped down.
Lockout Tab
Locking-Pin
When repositioning multiple Evolution decks in the empty position, the arms can be rotated down onto the deck surface, or “collapsed” and stacked three-high or four-high for rail transport.
17
www.fontaineintermodal.comFor service call 205-385-0451
To order parts call: 866-382-7278
Section 2 - Arm Operation (continued)
1. Make sure arms are in the down position.
2. Move the Intermodal Box Connectors (IBCs/twistlocks) from the disengaged position on the side of the arm and insert them into the stacking block casting to engage the locks. Note: Evolution flat decks can be stacked three-high or four-high to reposition. On the top flat deck of the stack, the twist locks should be in the disengaged position so that the crane can load/unload the stack
3. Check ground surface before stacking units to ensure safety.
Note: Evolution flat decks can be stacked three-high or four-high to reposition. On the top flat deck of the stack, the twist locks should be in the disengaged position so that the crane can load/unload the stack.
Stacking
NOTEFOR YARD STORAGE DECKS CAN BE STACKED AS HIGH AS 8 UNITS, BUT ONLY 1 CAN BE LIFTED AT A TIME WITH A FORKLIFT, OR FOUR AT A TIME WITH AN INTERMODAL OVERHEAD CRANE.
NOTEFOR REPOSITIONING PURPOSES, EVOLUTION DECKS CAN BE STACKED FOUR HIGH FOR ROAD AND RAIL TRANSPORT.
Engaged IBC
Stacking block
Twistlock
Insert twistlock into stacking block and engage.
Disengaged IBC
18
www.fontaineintermodal.comFor service call 205-385-0451
To order parts call: 866-382-7278
Section 3- Troubleshooting
Problem: Arm Support Brace hits the sides of the Lock Box when moving in or out.
Solution: Adjust the axle position in the Arm Support Brace in or out to achieve desired clearance. Use 3/4” SAE washers as spacers to position the arm so it clears the lock box as it moves in and out. Make sure to tighten lock nut after making the adjustment.
Problem: Locking-Pin will locate on curb side but not on road side.
Solution: Check lock box for damage. If there is no sign of damage, lock the curb side and crank the handle one or two more clicks. This will help to line up the Locking-Pin.
If it still will not locate properly, check the axle and wheel assembly in the Arm Support Brace for damage. If the axle is bent or damaged it could possibly not allow for the arm to locate. The in field/short term solution is to use the handle to pry the arm into position and pull the pin through. This is not a long term solution and could damage the deck over a period of time. The problem should be reported immediately and repaired as soon as possible.
Arm Alignment
The Locating-Pin is always the pin closest to the end of the deck and the Locking-Pin is always the
pin closest to the center of the deck.
19
www.fontaineintermodal.comFor service call 205-385-0451
To order parts call: 866-382-7278
Section 3- Troubleshooting (continued)
Problem: Locking-Pin is stuck or hard to slide.
Solution: First, try holding the pin handle in the "open thumb" position as this allows the force on the pin to be more in line with the hole location. Next, try to push on the yellow face of the Locking-Pin with the end of the crank handle.
WARNINGNEVER PUSH DIRECTLY ON A LOCKING-PIN OR A LOCATING-PIN WITH YOUR FINGER. USE THE END OF THE CRANK HANDLE TO PUSH DIRECTLY ON A LOCKING OR LOCATING-PIN.
Next, try to crank the arms up one or two clicks. If the pressure is off of the Locating-Pin, it will bind up the Locking-Pin. Do not over-torque the gearbox. If it will not turn without using excessive force then this is not the problem. (Never use a cheater bar!)
If these solutions do not work, lightly tap on the handle as close to the lock box as possible.
Worst case scenario, lightly tap on yellow tip of pin with a blunt object until the pin is recessed.
If it takes any if the last three to move the pin, check the face of the lockbox for visible damage.
NOTETIP: REGULAR APPLICATION OF GREASE TO THE EXPOSED SURFACE OF THE PIN WILL DECREASE FRICTION WHEN SLIDING PINS IN AND OUT (SEE SECTION 4-MAINTENANCE).
Problem: The handle is missing/broken from the Locking/Locating-Pin.
Solution: Short term solution, use a screwdriver or other slim tool to slide the pin in or out of position. Report problem immediately; pin will have to be replaced. Caution: never use a finger to push a pin.
WARNINGNEVER PUSH DIRECTLY ON A LOCKING-PIN OR A LOCATING-PIN WITH YOUR FINGER. USE THE END OF THE CRANK HANDLE TO PUSH DIRECTLY ON A LOCKING OR LOCATING-PIN.
Problem: The Arm Support Brace is hanging free and the axle/wheel assembly is broken.
Solution: Short term solution is to manually guide the arm into the locking position while cranking the arms into position. Then lock the pin normally. If "down" is the desired position, manually guide the Support Arm down while cranking and secure the arm to the deck using a winch strap. Report problem immediately.
Long term solution: Remove the broken piece from the arm using an adjustable wrench. Replace with a new assembly.
Arm Alignment (continued)
20
www.fontaineintermodal.comFor service call 205-385-0451
To order parts call: 866-382-7278
Section 4 - Maintenance
Following is a list of Preventative Maintenance items to be performed as needed (at least every 6 months). Most of these procedures are accomplished in a matter of minutes, and more frequent ongoing inspection is recommended.
The grease fittings in the connection between the main arm and the small arms should be greased.
Check for areas missing conspicuity tape, and check for major areas of rust or missing paint and for overall visible damage ( full length sides and rear).
Preventive Maintenance
Remove grease zerk access plug to lubricate the arm axle grease zerk with Red XP Grease (Extreme Pressure).
Zerk access plug
Lubricate axle zerk
21
www.fontaineintermodal.comFor service call 205-385-0451
To order parts call: 866-382-7278
Section 4 - Maintenance
Check Fontaine Crank Handle and polymer bushing.
The pin fastening the Arm Support Brace to the Arm Assembly is held in place by a washer welded on the inside. Visually inspect this area for cracks, damage or wear.
The Locking Pins and Locating Pins should be checked for visible damage and greased as needed.
All bolts should be checked for tightness. Hand tight is sufficient for test.
Check all toolbox doors to insure they are anchored properly to the deck and check for keys.
Preventive Maintenance (continued)
Crank Handle
Polymer Bushing
See Appendix A:Evolution Axle/Hub Bolt Installation/
Tightening/Maintenance
22
www.fontaineintermodal.comFor service call 205-385-0451
To order parts call: 866-382-7278
Section 4 - Maintenance (continued)
Check Rubber Bumper for visible damage.
Check floor area for visible damage.
Check forklift insert points for visible damage.
Check underneath crossmembers for visible damage.
Check the Arm Support Brace axle and wheel assemblies for damage.
Preventive Maintenance (continued)
23
www.fontaineintermodal.comFor service call 205-385-0451
To order parts call: 866-382-7278
Section 4 - Maintenance (continued)
Check for presence and security of all twistlocks.
Check for damaged decals/ unit numbers.
Check all winch stops are still in place.
Preventive Maintenance (continued)
IBC in disengaged
position
IBC in engaged position
24
www.fontaineintermodal.comFor service call 205-385-0451
To order parts call: 866-382-7278
Replacement Parts
©2013 • Fontaine Intermodal
Multiple locations on trailer
Steel end cap assembly(Page 42)
Tool box doors(Page 44)
Brake assembly(Page 32)
Crank handle(Page 34)
Brace wheel assembly(Page 31)
Bumper assembly(Page 33)
Curb side axle cap(Page 35)
Aluminum piece parts(Page 27)
Steel part pieces(Page 43)
Steel crossmember brackets(Page 41)
Decals(Page 36)
Huck and collar(Page 38)
Winches(Page 45)
Arm assembly(Page 28)
Gearbox assembly (Page 37)
Brace pin assembly(Page 30)
Lock box assembly(Page 40)
Aluminum deck piece parts(Page 26)
Arm axleassembly(Page 29)
IntermodalBox Connector
(IBC) (Page 39)
25
www.fontaineintermodal.comFor service call 205-385-0451
To order parts call: 866-382-7278
Aluminum deck piece parts ..............26Aluminum piece parts .......................27Arm assembly ..................................28Arm axle assembly ...........................29Brace pin assembly ..........................30Brace wheel assembly ......................31Brake assembly ................................32Bumper assembly ............................33Crank handle ....................................34Curb side axle cap ...........................35Decals ..............................................36Gearbox assembly ...........................37Huck and collar ................................38IBC (Intermodal Box Connectors) .....39Lock box assembly...........................40Steel crossmember brackets ............41Steel end cap assembly ...................42Steel part pieces ..............................43Tool box doors .................................44Winches ...........................................45
Contents
26
www.fontaineintermodal.comFor service call 205-385-0451
To order parts call: 866-382-7278
Aluminum deck piece parts
Floor end platePart #: 90012010
Corner capPart #: 90012002
27
www.fontaineintermodal.comFor service call 205-385-0451
To order parts call: 866-382-7278
Aluminum piece parts
Routed lock box Part #: 90010070
Routed arm cross beam Part #: 90010010
Coil package cross beamPart #: 90010020
Storage box floorPart #: 90010037
Front tool box weldmentPart #: 90010700 Forklift tube top
plate extrusionPart #: 90010038
Fork lift tube top supportPart #: 90010030
Storage box I-beam Part #: 90010035
Spacer I-beamPart #: 90010036
Aluminum pieces are at multiple locations
28
www.fontaineintermodal.comFor service call 205-385-0451
To order parts call: 866-382-7278
Arm assembly
Front arm assembly Part #: 90013000F
Arm support brace Part #: 90014000
Rear arm assembly Part #: 90013000R
Arm axle bushing Part #: 90010004
29
www.fontaineintermodal.comFor service call 205-385-0451
To order parts call: 866-382-7278
Arm axlePart #: 90010060
5/8”x 2” SHCS bolt UNCPart #: 90017007
Arm axle assembly
30
www.fontaineintermodal.comFor service call 205-385-0451
To order parts call: 866-382-7278
Brace pin weldmentPart #: 90010050
Brace pin washerPart #: 90010053
NOTE: Brace pin washer is welded to the pin on the inside to retain pin in place.
Brace pin assembly
31
www.fontaineintermodal.comFor service call 205-385-0451
To order parts call: 866-382-7278
Brace wheel assemblyPart #: 90010040
SAE Washers (4)Part #: 90017037
Bushing (1)Part #: 90017038
Lock nut ¾” UNC Nylon InsertPart #: 90017006
Brace wheel assembly
32
www.fontaineintermodal.comFor service call 205-385-0451
To order parts call: 866-382-7278
Brake axle assembly(right hand)
Part #: 90010502
Arm drive bushingPart #: 90010007
Arm drive flange gasketPart #: 90010009
Brake assembly keyPart #: 90010526
½"x 1¼" SHCS bolt UNCPart #: 90017004
M12x 25mm SHCWS boltPart #: 90017005
Serrated flat washer- 1/2”Part #: 90017001
Brake axle assembly(left hand)
Part #: 90010501
Brake assembly
See Appendix A:Evolution Axle/Hub Bolt Installation/
Tightening/Maintenance
33
www.fontaineintermodal.comFor service call 205-385-0451
To order parts call: 866-382-7278
Bumper bracketPart #: 90011300
Carriage bolt 3/8"x 1 ¾" UNC grade 5Part #: 90017008
3/8" USS flat washerPart #: 90017009
3/8" lock nut UNC nylon insertPart #: 90017010Support bumper
Part #: 90010008
Bumper assembly
Brace Arm RetainerPart #: 90011390
34
www.fontaineintermodal.comFor service call 205-385-0451
To order parts call: 866-382-7278
Fontaine crank handlePart #: 90017028
Crank handle
35
www.fontaineintermodal.comFor service call 205-385-0451
To order parts call: 866-382-7278
Curb side axle cap
Arm drive end flange–curb sidePart #: 90010005
Located under trailer on both ends
½"x 1¼" SHCS bolt UNCPart #: 90017004
Serrated flat washer- 1-2”Part #: 90017001
36
www.fontaineintermodal.comFor service call 205-385-0451
To order parts call: 866-382-7278
Decals
“Front” decal Quantity (2)
Part #: 90010903
Note: page 5-7 shows many decal locations
Arrow decal Quantity (2)
Part #: 90010909
DOT 49 CFR decal Quantity (4)
Part #: 90010916
Caution decal Quantity (2)
Part #: 90010917
Fontaine plaque Quantity (2)
Part #: 90010950
Conspicuity decal Part #: 90010951
Unit NumbersQuantity (2)
Part #: 90010918
Dimension decalQuantity (4)
Part #: 90010914
Height decalQuantity (4)
Part #: 90010904
Reflector decal
Website decal
Caution decal
WWW.FONTAINE INTERMODAL.COM
WARNING:DO NOT BUMP ARMS WITH FORKS
Black/Yellow decalPart #: 90010952
Danger decal Quantity (4)
Part #: 90010910
CMVSS 905 decal Quantity (4)
Part #: 90010911
“Front” decal Quantity (1)
Part #: 90010912
Caution decal Quantity (4)
Part #: 90010905
Caution decal Quantity (2)
Part #: 90010906
“For empty only” decal Quantity (2)
Part #: 90010907
“WTP” white reflectiveQuantity (6)
Part #: 90010908
Contact decalQuantity (1)
Part #: 90010915
PLACE SINGLE COIL HERE
37
www.fontaineintermodal.comFor service call 205-385-0451
To order parts call: 866-382-7278
GearboxPart #: 90015000 ½"x 4 ½" SHCS bolt
UNCPart #: 90017002
½" lock washerPart #: 90017007
½" nut UNCPart #: 90017003
Gearbox assembly
38
www.fontaineintermodal.comFor service call 205-385-0451
To order parts call: 866-382-7278
Huck and Collar
25/64” Huck PinPart #: 90015001
25/64” Huck CollarPart #: 90015002
Multiple locations on trailer
39
www.fontaineintermodal.comFor service call 205-385-0451
To order parts call: 866-382-7278
IBC (Intermodal Box Connectors)
IBC (Intermodal Box Connectors)Road side front and curb side rear
Part #: 90013430
IBC (Intermodal Box Connectors)Curb side front and road side rear
Part #: 90013440
40
www.fontaineintermodal.comFor service call 205-385-0451
To order parts call: 866-382-7278
Lock box assemblyPart #: 90011600
Lock box stiffenerPart #: 90011622 ½"x 1½" NC Hex
head boltPart #: 90017025
¾" lock washerPart #: 90017024
½" Lock nut with nylon insert NCPart #: 90017026
Lock box handlePart #: 90010002
Lock box pinPart #: 90010001
Yellow rubber handle gripPart #: 90010003
Lock box assembly
41
www.fontaineintermodal.comFor service call 205-385-0451
To order parts call: 866-382-7278
Steel crossmember brackets
Lock box X-beam right rear mount bracketPart #: 90011633
Lock box X-beam left rear mount bracket
Part #: 90011632
Lock box X-beam front mount bracket
Part #: 90011631
X-brace right bracketPart #: 90011041
MTR mount X-brace left bracketPart #: 90011044
X-brace left bracketPart #: 90011042
MTR mount X-brace right bracket
Part #: 90011043
Steel pieces are at multiple locations
42
www.fontaineintermodal.comFor service call 205-385-0451
To order parts call: 866-382-7278
Steel end cap assembly
Front and rear skirtPart #: 90011200
Front and rear skirt cover platePart #: 90011211
Frame end cap gussetPart #: 90011212
43
www.fontaineintermodal.comFor service call 205-385-0451
To order parts call: 866-382-7278
Steel part pieces
Steel cross brace Part #: 90011010
Arm brace box top gusset 9-1/4" long
Part #: 90011008
Gear reducer bracket brace11-15/16" x 1-5/8"Part #: 90011007
Gear reducer mount platePart #: 90011006
Forklift tube reinforcement tab12-15/16" x 2-5/8"Part #: 90011002
Coil PX X-Brace mount tab8" x 3"
Part #: 90011001
Steel pieces are at multiple locations
44
www.fontaineintermodal.comFor service call 205-385-0451
To order parts call: 866-382-7278
Tool box doors
Bottom hinge toolbox door (rear)Part #: 90010093
Side Hinge toolbox door (front)Part #: 90010090
45
www.fontaineintermodal.comFor service call 205-385-0451
To order parts call: 866-382-7278
Ancra Double L winchNote: strap not included
Part #: 90017012
Winches slide for multiple positions
4"x 30' Xtreme orange winch strap AncraPart #: 90017013
Winch strap hook holder
Part #: 90017014
Winches
46
www.fontaineintermodal.comFor service call 205-385-0451
To order parts call: 866-382-7278
2014 Business Plan Overview
Appendix AEvolution Axle/Hub Bolt Installation/Tightening/Maintenance
47
www.fontaineintermodal.comFor service call 205-385-0451
To order parts call: 866-382-7278
Evolution Axle/Hub BoltInstallation/Tightening/Maintenance
Appendix AEvolution Axle/Hub Bolt Installation/Tightening/Maintenance
48
www.fontaineintermodal.comFor service call 205-385-0451
To order parts call: 866-382-7278
Step 1: Clamp Arm
Appendix AEvolution Axle/Hub Bolt Installation/Tightening/Maintenance
49
www.fontaineintermodal.comFor service call 205-385-0451
To order parts call: 866-382-7278
Clamping Arm• Place clamp through siderail pocket and
outside of arm nearest the axle• Tighten clamp until arm is secure against the
axle tube (as shown in previous slide)
Note: Arm must be clamped to completely tighten bolts. Otherwise a false torque will result in loosening of the bolts after first cycle of arm.
Appendix AEvolution Axle/Hub Bolt Installation/Tightening/Maintenance
50
www.fontaineintermodal.comFor service call 205-385-0451
To order parts call: 866-382-7278
Step 2: Hardware/Prep
Appendix AEvolution Axle/Hub Bolt Installation/Tightening/Maintenance
51
www.fontaineintermodal.comFor service call 205-385-0451
To order parts call: 866-382-7278
Preparing for Bolt install• Place serrated washer on bolt• Apply Loctite 2760 to threads of bolt
Note: Proper application of threadlocker when using a plated bolt requires a primer be used. Loctite 2760 is primerless and eliminates this step.
Appendix AEvolution Axle/Hub Bolt Installation/Tightening/Maintenance
52
www.fontaineintermodal.comFor service call 205-385-0451
To order parts call: 866-382-7278
Step 3: Install Bolts• With Bolts prepped, begin threading bolts
through the brake/cam assembly into axle• Once all 8 bolts are in, begin tightening
the bolts• Using a alternating pattern, tighten all bolts
Appendix AEvolution Axle/Hub Bolt Installation/Tightening/Maintenance
53
www.fontaineintermodal.comFor service call 205-385-0451
To order parts call: 866-382-7278
Step 4: Final Check• After all bolt have been tightened,
remove clamp • Cycle arm one time• Recheck bolts for tightness• Process is now complete
Appendix AEvolution Axle/Hub Bolt Installation/Tightening/Maintenance
54
www.fontaineintermodal.comFor service call 205-385-0451
To order parts call: 866-382-7278
Preventative Maintenance• Periodically Steps 1 & 3 should be repeated to
check for any possible loosening
Appendix AEvolution Axle/Hub Bolt Installation/Tightening/Maintenance
55
www.fontaineintermodal.comFor service call 205-385-0451
To order parts call: 866-382-7278
Fontaine Intermodal3515 Industrial Way
Jasper, Alabama 35501
www.fontaineintermodal.com
205-385-0451
The Evolution intermodal flat deck is the perfect solution for converting
flatbed freight from road to rail, allowing forward thinking freight companies to take
full advantage of the highly efficient and cost effective North American
intermodal rail network.
©2017 • Fontaine Intermodal • R14